| /* |
| * Trantor T128/T128F/T228 defines |
| * Note : architecturally, the T100 and T128 are different and won't work |
| * |
| * Copyright 1993, Drew Eckhardt |
| * Visionary Computing |
| * (Unix and Linux consulting and custom programming) |
| * drew@colorado.edu |
| * +1 (303) 440-4894 |
| * |
| * DISTRIBUTION RELEASE 3. |
| * |
| * For more information, please consult |
| * |
| * Trantor Systems, Ltd. |
| * T128/T128F/T228 SCSI Host Adapter |
| * Hardware Specifications |
| * |
| * Trantor Systems, Ltd. |
| * 5415 Randall Place |
| * Fremont, CA 94538 |
| * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 |
| * |
| * and |
| * |
| * NCR 5380 Family |
| * SCSI Protocol Controller |
| * Databook |
| * |
| * NCR Microelectronics |
| * 1635 Aeroplaza Drive |
| * Colorado Springs, CO 80916 |
| * 1+ (719) 578-3400 |
| * 1+ (800) 334-5454 |
| */ |
| |
| /* |
| * $Log: t128.h,v $ |
| */ |
| |
| #ifndef T128_H |
| #define T128_H |
| |
| #define T128_PUBLIC_RELEASE 3 |
| |
| #define TDEBUG 0 |
| #define TDEBUG_INIT 0x1 |
| #define TDEBUG_TRANSFER 0x2 |
| |
| /* |
| * The trantor boards are memory mapped. They use an NCR5380 or |
| * equivalent (my sample board had part second sourced from ZILOG). |
| * NCR's recommended "Pseudo-DMA" architecture is used, where |
| * a PAL drives the DMA signals on the 5380 allowing fast, blind |
| * transfers with proper handshaking. |
| */ |
| |
| /* |
| * Note : a boot switch is provided for the purpose of informing the |
| * firmware to boot or not boot from attached SCSI devices. So, I imagine |
| * there are fewer people who've yanked the ROM like they do on the Seagate |
| * to make bootup faster, and I'll probably use this for autodetection. |
| */ |
| #define T_ROM_OFFSET 0 |
| |
| /* |
| * Note : my sample board *WAS NOT* populated with the SRAM, so this |
| * can't be used for autodetection without a ROM present. |
| */ |
| #define T_RAM_OFFSET 0x1800 |
| |
| /* |
| * All of the registers are allocated 32 bytes of address space, except |
| * for the data register (read/write to/from the 5380 in pseudo-DMA mode) |
| */ |
| #define T_CONTROL_REG_OFFSET 0x1c00 /* rw */ |
| #define T_CR_INT 0x10 /* Enable interrupts */ |
| #define T_CR_CT 0x02 /* Reset watchdog timer */ |
| |
| #define T_STATUS_REG_OFFSET 0x1c20 /* ro */ |
| #define T_ST_BOOT 0x80 /* Boot switch */ |
| #define T_ST_S3 0x40 /* User settable switches, */ |
| #define T_ST_S2 0x20 /* read 0 when switch is on, 1 off */ |
| #define T_ST_S1 0x10 |
| #define T_ST_PS2 0x08 /* Set for Microchannel 228 */ |
| #define T_ST_RDY 0x04 /* 5380 DRQ */ |
| #define T_ST_TIM 0x02 /* indicates 40us watchdog timer fired */ |
| #define T_ST_ZERO 0x01 /* Always zero */ |
| |
| #define T_5380_OFFSET 0x1d00 /* 8 registers here, see NCR5380.h */ |
| |
| #define T_DATA_REG_OFFSET 0x1e00 /* rw 512 bytes long */ |
| |
| #ifndef ASM |
| static int t128_abort(struct scsi_cmnd *); |
| static int t128_biosparam(struct scsi_device *, struct block_device *, |
| sector_t, int*); |
| static int t128_detect(struct scsi_host_template *); |
| static int t128_queue_command(struct scsi_cmnd *, |
| void (*done)(struct scsi_cmnd *)); |
| static int t128_bus_reset(struct scsi_cmnd *); |
| |
| #ifndef CMD_PER_LUN |
| #define CMD_PER_LUN 2 |
| #endif |
| |
| #ifndef CAN_QUEUE |
| #define CAN_QUEUE 32 |
| #endif |
| |
| #ifndef HOSTS_C |
| |
| #define NCR5380_implementation_fields \ |
| void __iomem *base |
| |
| #define NCR5380_local_declare() \ |
| void __iomem *base |
| |
| #define NCR5380_setup(instance) \ |
| base = ((struct NCR5380_hostdata *)(instance->hostdata))->base |
| |
| #define T128_address(reg) (base + T_5380_OFFSET + ((reg) * 0x20)) |
| |
| #if !(TDEBUG & TDEBUG_TRANSFER) |
| #define NCR5380_read(reg) readb(T128_address(reg)) |
| #define NCR5380_write(reg, value) writeb((value),(T128_address(reg))) |
| #else |
| #define NCR5380_read(reg) \ |
| (((unsigned char) printk("scsi%d : read register %d at address %08x\n"\ |
| , instance->hostno, (reg), T128_address(reg))), readb(T128_address(reg))) |
| |
| #define NCR5380_write(reg, value) { \ |
| printk("scsi%d : write %02x to register %d at address %08x\n", \ |
| instance->hostno, (value), (reg), T128_address(reg)); \ |
| writeb((value), (T128_address(reg))); \ |
| } |
| #endif |
| |
| #define NCR5380_intr t128_intr |
| #define do_NCR5380_intr do_t128_intr |
| #define NCR5380_queue_command t128_queue_command |
| #define NCR5380_abort t128_abort |
| #define NCR5380_bus_reset t128_bus_reset |
| #define NCR5380_proc_info t128_proc_info |
| |
| /* 15 14 12 10 7 5 3 |
| 1101 0100 1010 1000 */ |
| |
| #define T128_IRQS 0xc4a8 |
| |
| #endif /* else def HOSTS_C */ |
| #endif /* ndef ASM */ |
| #endif /* T128_H */ |