drivers/media/radio/Kconfig - kernel/msm-4.9 - Gitiles

 #
 # Multimedia Video device configuration
 #

 menu "Radio Adapters"
 	depends on VIDEO_DEV!=n

 config RADIO_CADET
 	tristate "ADS Cadet AM/FM Tuner"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these AM/FM radio cards, and then
 	  fill in the port address below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  Further documentation on this driver can be found on the WWW at
 	  <http://linux.blackhawke.net/cadet/>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-cadet.

 config RADIO_RTRACK
 	tristate "AIMSlab RadioTrack (aka RadioReveal) support"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards, and then fill
 	  in the port address below.

 	  Note that newer AIMSlab RadioTrack cards have a different chipset
 	  and are not supported by this driver.  For these cards, use the
 	  RadioTrack II driver below.

 	  If you have a GemTeks combined (PnP) sound- and radio card you must
 	  use this driver as a module and setup the card with isapnptools.
 	  You must also pass the module a suitable io parameter, 0x248 has
 	  been reported to be used by these cards.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>. More information is
 	  contained in the file
 	  <file:Documentation/video4linux/radiotrack.txt>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-aimslab.

 config RADIO_RTRACK_PORT
 	hex "RadioTrack i/o port (0x20f or 0x30f)"
 	depends on RADIO_RTRACK=y
 	default "20f"
 	help
 	  Enter either 0x30f or 0x20f here.  The card default is 0x30f, if you
 	  haven't changed the jumper setting on the card.

 config RADIO_RTRACK2
 	tristate "AIMSlab RadioTrack II support"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have this FM radio card, and then fill in the
 	  port address below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-rtrack2.

 config RADIO_RTRACK2_PORT
 	hex "RadioTrack II i/o port (0x20c or 0x30c)"
 	depends on RADIO_RTRACK2=y
 	default "30c"
 	help
 	  Enter either 0x30c or 0x20c here.  The card default is 0x30c, if you
 	  haven't changed the jumper setting on the card.

 config RADIO_AZTECH
 	tristate "Aztech/Packard Bell Radio"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards, and then fill
 	  in the port address below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-aztech.

 config RADIO_AZTECH_PORT
 	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
 	depends on RADIO_AZTECH=y
 	default "350"
 	help
 	  Enter either 0x350 or 0x358 here.  The card default is 0x350, if you
 	  haven't changed the setting of jumper JP3 on the card.  Removing the
 	  jumper sets the card to 0x358.

 config RADIO_GEMTEK
 	tristate "GemTek Radio Card support"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have this FM radio card, and then fill in the
 	  port address below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-gemtek.

 config RADIO_GEMTEK_PORT
 	hex "GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)"
 	depends on RADIO_GEMTEK=y
 	default "34c"
 	help
 	  Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
 	  0x34c, if you haven't changed the jumper setting on the card. On
 	  Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
 	  port is 0x28c.

 config RADIO_GEMTEK_PCI
 	tristate "GemTek PCI Radio Card support"
 	depends on VIDEO_V4L2 && PCI
 	---help---
 	  Choose Y here if you have this PCI FM radio card.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video for Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-gemtek-pci.

 config RADIO_MAXIRADIO
 	tristate "Guillemot MAXI Radio FM 2000 radio"
 	depends on VIDEO_V4L2 && PCI
 	---help---
 	  Choose Y here if you have this radio card.  This card may also be
 	  found as Gemtek PCI FM.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-maxiradio.

 config RADIO_MAESTRO
 	tristate "Maestro on board radio"
 	depends on VIDEO_V4L2 && PCI
 	---help---
 	  Say Y here to directly support the on-board radio tuner on the
 	  Maestro 2 or 2E sound card.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-maestro.

 config RADIO_MIROPCM20
 	tristate "miroSOUND PCM20 radio"
 	depends on ISA && VIDEO_V4L1 && SOUND_ACI_MIXER
 	---help---
 	  Choose Y here if you have this FM radio card. You also need to say Y
 	  to "ACI mixer (miroSOUND PCM1-pro/PCM12/PCM20 radio)" (in "Sound")
 	  for this to work.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called miropcm20.

 config RADIO_MIROPCM20_RDS
 	tristate "miroSOUND PCM20 radio RDS user interface (EXPERIMENTAL)"
 	depends on RADIO_MIROPCM20 && EXPERIMENTAL
 	---help---
 	  Choose Y here if you want to see RDS/RBDS information like
 	  RadioText, Programme Service name, Clock Time and date, Programme
 	  Type and Traffic Announcement/Programme identification.

 	  It's not possible to read the raw RDS packets from the device, so
 	  the driver cant provide an V4L interface for this.  But the
 	  availability of RDS is reported over V4L by the basic driver
 	  already.  Here RDS can be read from files in /dev/v4l/rds.

 	  To compile this driver as a module, choose M here: the
 	  module will be called miropcm20-rds.

 config RADIO_SF16FMI
 	tristate "SF16FMI Radio"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards.  If you
 	  compile the driver into the kernel and your card is not PnP one, you
 	  have to add "sf16fm=<io>" to the kernel command line (I/O address is
 	  0x284 or 0x384).

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-sf16fmi.

 config RADIO_SF16FMR2
 	tristate "SF16FMR2 Radio"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found on the WWW at
 	  <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-sf16fmr2.

 config RADIO_TERRATEC
 	tristate "TerraTec ActiveRadio ISA Standalone"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have this FM radio card, and then fill in the
 	  port address below. (TODO)

 	  Note: This driver is in its early stages.  Right now volume and
 	  frequency control and muting works at least for me, but
 	  unfortunately I have not found anybody who wants to use this card
 	  with Linux.  So if it is this what YOU are trying to do right now,
 	  PLEASE DROP ME A NOTE!!  Rolf Offermanns <rolf@offermanns.de>.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-terratec.

 config RADIO_TERRATEC_PORT
 	hex "Terratec i/o port (normally 0x590)"
 	depends on RADIO_TERRATEC=y
 	default "590"
 	help
 	  Fill in the I/O port of your TerraTec FM radio card. If unsure, go
 	  with the default.

 config RADIO_TRUST
 	tristate "Trust FM radio card"
 	depends on ISA && VIDEO_V4L2
 	help
 	  This is a driver for the Trust FM radio cards. Say Y if you have
 	  such a card and want to use it under Linux.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-trust.

 config RADIO_TRUST_PORT
 	hex "Trust i/o port (usually 0x350 or 0x358)"
 	depends on RADIO_TRUST=y
 	default "350"
 	help
 	  Enter the I/O port of your Trust FM radio card. If unsure, try the
 	  values "0x350" or "0x358".

 config RADIO_TYPHOON
 	tristate "Typhoon Radio (a.k.a. EcoRadio)"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards, and then fill
 	  in the port address and the frequency used for muting below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-typhoon.

 config RADIO_TYPHOON_PROC_FS
 	bool "Support for /proc/radio-typhoon"
 	depends on PROC_FS && RADIO_TYPHOON
 	help
 	  Say Y here if you want the typhoon radio card driver to write
 	  status information (frequency, volume, muted, mute frequency,
 	  base address) to /proc/radio-typhoon. The file can be viewed with
 	  your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
 	  /proc/radio-typhoon" or simply "cat /proc/radio-typhoon").

 config RADIO_TYPHOON_PORT
 	hex "Typhoon I/O port (0x316 or 0x336)"
 	depends on RADIO_TYPHOON=y
 	default "316"
 	help
 	  Enter the I/O port of your Typhoon or EcoRadio radio card.

 config RADIO_TYPHOON_MUTEFREQ
 	int "Typhoon frequency set when muting the device (kHz)"
 	depends on RADIO_TYPHOON=y
 	default "87500"
 	help
 	  Enter the frequency used for muting the radio. The device is never
 	  completely silent. If the volume is just turned down, you can still
 	  hear silent voices and music. For that reason, the frequency of the
 	  radio device is set to the frequency you can enter here whenever
 	  the device is muted. There should be no local radio station at that
 	  frequency.

 config RADIO_ZOLTRIX
 	tristate "Zoltrix Radio"
 	depends on ISA && VIDEO_V4L2
 	---help---
 	  Choose Y here if you have one of these FM radio cards, and then fill
 	  in the port address below.

 	  In order to control your radio card, you will need to use programs
 	  that are compatible with the Video For Linux API.  Information on
 	  this API and pointers to "v4l" programs may be found at
 	  <file:Documentation/video4linux/API.html>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called radio-zoltrix.

 config RADIO_ZOLTRIX_PORT
 	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
 	depends on RADIO_ZOLTRIX=y
 	default "20c"
 	help
 	  Enter the I/O port of your Zoltrix radio card.

 config USB_DSBR
 	tristate "D-Link USB FM radio support (EXPERIMENTAL)"
 	depends on USB && VIDEO_V4L2 && EXPERIMENTAL
 	---help---
 	  Say Y here if you want to connect this type of radio to your
 	  computer's USB port. Note that the audio is not digital, and
 	  you must connect the line out connector to a sound card or a
 	  set of speakers.

 	  To compile this driver as a module, choose M here: the
 	  module will be called dsbr100.
 endmenu
	#
	# Multimedia Video device configuration
	#

	menu "Radio Adapters"
	depends on VIDEO_DEV!=n

	config RADIO_CADET
	tristate "ADS Cadet AM/FM Tuner"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these AM/FM radio cards, and then
	fill in the port address below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	Further documentation on this driver can be found on the WWW at
	<http://linux.blackhawke.net/cadet/>.

	To compile this driver as a module, choose M here: the
	module will be called radio-cadet.

	config RADIO_RTRACK
	tristate "AIMSlab RadioTrack (aka RadioReveal) support"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards, and then fill
	in the port address below.

	Note that newer AIMSlab RadioTrack cards have a different chipset
	and are not supported by this driver. For these cards, use the
	RadioTrack II driver below.

	If you have a GemTeks combined (PnP) sound- and radio card you must
	use this driver as a module and setup the card with isapnptools.
	You must also pass the module a suitable io parameter, 0x248 has
	been reported to be used by these cards.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>. More information is
	contained in the file
	<file:Documentation/video4linux/radiotrack.txt>.

	To compile this driver as a module, choose M here: the
	module will be called radio-aimslab.

	config RADIO_RTRACK_PORT
	hex "RadioTrack i/o port (0x20f or 0x30f)"
	depends on RADIO_RTRACK=y
	default "20f"
	help
	Enter either 0x30f or 0x20f here. The card default is 0x30f, if you
	haven't changed the jumper setting on the card.

	config RADIO_RTRACK2
	tristate "AIMSlab RadioTrack II support"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have this FM radio card, and then fill in the
	port address below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-rtrack2.

	config RADIO_RTRACK2_PORT
	hex "RadioTrack II i/o port (0x20c or 0x30c)"
	depends on RADIO_RTRACK2=y
	default "30c"
	help
	Enter either 0x30c or 0x20c here. The card default is 0x30c, if you
	haven't changed the jumper setting on the card.

	config RADIO_AZTECH
	tristate "Aztech/Packard Bell Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards, and then fill
	in the port address below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-aztech.

	config RADIO_AZTECH_PORT
	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
	depends on RADIO_AZTECH=y
	default "350"
	help
	Enter either 0x350 or 0x358 here. The card default is 0x350, if you
	haven't changed the setting of jumper JP3 on the card. Removing the
	jumper sets the card to 0x358.

	config RADIO_GEMTEK
	tristate "GemTek Radio Card support"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have this FM radio card, and then fill in the
	port address below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-gemtek.

	config RADIO_GEMTEK_PORT
	hex "GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)"
	depends on RADIO_GEMTEK=y
	default "34c"
	help
	Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
	0x34c, if you haven't changed the jumper setting on the card. On
	Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
	port is 0x28c.

	config RADIO_GEMTEK_PCI
	tristate "GemTek PCI Radio Card support"
	depends on VIDEO_V4L2 && PCI
	---help---
	Choose Y here if you have this PCI FM radio card.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video for Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-gemtek-pci.

	config RADIO_MAXIRADIO
	tristate "Guillemot MAXI Radio FM 2000 radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	Choose Y here if you have this radio card. This card may also be
	found as Gemtek PCI FM.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-maxiradio.

	config RADIO_MAESTRO
	tristate "Maestro on board radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	Say Y here to directly support the on-board radio tuner on the
	Maestro 2 or 2E sound card.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-maestro.

	config RADIO_MIROPCM20
	tristate "miroSOUND PCM20 radio"
	depends on ISA && VIDEO_V4L1 && SOUND_ACI_MIXER
	---help---
	Choose Y here if you have this FM radio card. You also need to say Y
	to "ACI mixer (miroSOUND PCM1-pro/PCM12/PCM20 radio)" (in "Sound")
	for this to work.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called miropcm20.

	config RADIO_MIROPCM20_RDS
	tristate "miroSOUND PCM20 radio RDS user interface (EXPERIMENTAL)"
	depends on RADIO_MIROPCM20 && EXPERIMENTAL
	---help---
	Choose Y here if you want to see RDS/RBDS information like
	RadioText, Programme Service name, Clock Time and date, Programme
	Type and Traffic Announcement/Programme identification.

	It's not possible to read the raw RDS packets from the device, so
	the driver cant provide an V4L interface for this. But the
	availability of RDS is reported over V4L by the basic driver
	already. Here RDS can be read from files in /dev/v4l/rds.

	To compile this driver as a module, choose M here: the
	module will be called miropcm20-rds.

	config RADIO_SF16FMI
	tristate "SF16FMI Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards. If you
	compile the driver into the kernel and your card is not PnP one, you
	have to add "sf16fm=<io>" to the kernel command line (I/O address is
	0x284 or 0x384).

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-sf16fmi.

	config RADIO_SF16FMR2
	tristate "SF16FMR2 Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found on the WWW at
	<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.

	To compile this driver as a module, choose M here: the
	module will be called radio-sf16fmr2.

	config RADIO_TERRATEC
	tristate "TerraTec ActiveRadio ISA Standalone"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have this FM radio card, and then fill in the
	port address below. (TODO)

	Note: This driver is in its early stages. Right now volume and
	frequency control and muting works at least for me, but
	unfortunately I have not found anybody who wants to use this card
	with Linux. So if it is this what YOU are trying to do right now,
	PLEASE DROP ME A NOTE!! Rolf Offermanns <rolf@offermanns.de>.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-terratec.

	config RADIO_TERRATEC_PORT
	hex "Terratec i/o port (normally 0x590)"
	depends on RADIO_TERRATEC=y
	default "590"
	help
	Fill in the I/O port of your TerraTec FM radio card. If unsure, go
	with the default.

	config RADIO_TRUST
	tristate "Trust FM radio card"
	depends on ISA && VIDEO_V4L2
	help
	This is a driver for the Trust FM radio cards. Say Y if you have
	such a card and want to use it under Linux.

	To compile this driver as a module, choose M here: the
	module will be called radio-trust.

	config RADIO_TRUST_PORT
	hex "Trust i/o port (usually 0x350 or 0x358)"
	depends on RADIO_TRUST=y
	default "350"
	help
	Enter the I/O port of your Trust FM radio card. If unsure, try the
	values "0x350" or "0x358".

	config RADIO_TYPHOON
	tristate "Typhoon Radio (a.k.a. EcoRadio)"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards, and then fill
	in the port address and the frequency used for muting below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-typhoon.

	config RADIO_TYPHOON_PROC_FS
	bool "Support for /proc/radio-typhoon"
	depends on PROC_FS && RADIO_TYPHOON
	help
	Say Y here if you want the typhoon radio card driver to write
	status information (frequency, volume, muted, mute frequency,
	base address) to /proc/radio-typhoon. The file can be viewed with
	your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
	/proc/radio-typhoon" or simply "cat /proc/radio-typhoon").

	config RADIO_TYPHOON_PORT
	hex "Typhoon I/O port (0x316 or 0x336)"
	depends on RADIO_TYPHOON=y
	default "316"
	help
	Enter the I/O port of your Typhoon or EcoRadio radio card.

	config RADIO_TYPHOON_MUTEFREQ
	int "Typhoon frequency set when muting the device (kHz)"
	depends on RADIO_TYPHOON=y
	default "87500"
	help
	Enter the frequency used for muting the radio. The device is never
	completely silent. If the volume is just turned down, you can still
	hear silent voices and music. For that reason, the frequency of the
	radio device is set to the frequency you can enter here whenever
	the device is muted. There should be no local radio station at that
	frequency.

	config RADIO_ZOLTRIX
	tristate "Zoltrix Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	Choose Y here if you have one of these FM radio cards, and then fill
	in the port address below.

	In order to control your radio card, you will need to use programs
	that are compatible with the Video For Linux API. Information on
	this API and pointers to "v4l" programs may be found at
	<file:Documentation/video4linux/API.html>.

	To compile this driver as a module, choose M here: the
	module will be called radio-zoltrix.

	config RADIO_ZOLTRIX_PORT
	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
	depends on RADIO_ZOLTRIX=y
	default "20c"
	help
	Enter the I/O port of your Zoltrix radio card.

	config USB_DSBR
	tristate "D-Link USB FM radio support (EXPERIMENTAL)"
	depends on USB && VIDEO_V4L2 && EXPERIMENTAL
	---help---
	Say Y here if you want to connect this type of radio to your
	computer's USB port. Note that the audio is not digital, and
	you must connect the line out connector to a sound card or a
	set of speakers.

	To compile this driver as a module, choose M here: the
	module will be called dsbr100.
	endmenu