| /* |
| * Copyright (c) 2016-2017, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #define pr_fmt(fmt) "dsi-phy-hw:" fmt |
| #include <linux/math64.h> |
| #include <linux/delay.h> |
| #include <linux/iopoll.h> |
| #include "dsi_hw.h" |
| #include "dsi_phy_hw.h" |
| |
| #define DSIPHY_CMN_CLK_CFG0 0x010 |
| #define DSIPHY_CMN_CLK_CFG1 0x014 |
| #define DSIPHY_CMN_GLBL_CTRL 0x018 |
| #define DSIPHY_CMN_RBUF_CTRL 0x01C |
| #define DSIPHY_CMN_VREG_CTRL 0x020 |
| #define DSIPHY_CMN_CTRL_0 0x024 |
| #define DSIPHY_CMN_CTRL_1 0x028 |
| #define DSIPHY_CMN_CTRL_2 0x02C |
| #define DSIPHY_CMN_LANE_CFG0 0x030 |
| #define DSIPHY_CMN_LANE_CFG1 0x034 |
| #define DSIPHY_CMN_PLL_CNTRL 0x038 |
| #define DSIPHY_CMN_LANE_CTRL0 0x098 |
| #define DSIPHY_CMN_LANE_CTRL1 0x09C |
| #define DSIPHY_CMN_LANE_CTRL2 0x0A0 |
| #define DSIPHY_CMN_LANE_CTRL3 0x0A4 |
| #define DSIPHY_CMN_LANE_CTRL4 0x0A8 |
| #define DSIPHY_CMN_TIMING_CTRL_0 0x0AC |
| #define DSIPHY_CMN_TIMING_CTRL_1 0x0B0 |
| #define DSIPHY_CMN_TIMING_CTRL_2 0x0B4 |
| #define DSIPHY_CMN_TIMING_CTRL_3 0x0B8 |
| #define DSIPHY_CMN_TIMING_CTRL_4 0x0BC |
| #define DSIPHY_CMN_TIMING_CTRL_5 0x0C0 |
| #define DSIPHY_CMN_TIMING_CTRL_6 0x0C4 |
| #define DSIPHY_CMN_TIMING_CTRL_7 0x0C8 |
| #define DSIPHY_CMN_TIMING_CTRL_8 0x0CC |
| #define DSIPHY_CMN_TIMING_CTRL_9 0x0D0 |
| #define DSIPHY_CMN_TIMING_CTRL_10 0x0D4 |
| #define DSIPHY_CMN_TIMING_CTRL_11 0x0D8 |
| #define DSIPHY_CMN_PHY_STATUS 0x0EC |
| #define DSIPHY_CMN_LANE_STATUS0 0x0F4 |
| #define DSIPHY_CMN_LANE_STATUS1 0x0F8 |
| |
| |
| /* n = 0..3 for data lanes and n = 4 for clock lane */ |
| #define DSIPHY_LNX_CFG0(n) (0x200 + (0x80 * (n))) |
| #define DSIPHY_LNX_CFG1(n) (0x204 + (0x80 * (n))) |
| #define DSIPHY_LNX_CFG2(n) (0x208 + (0x80 * (n))) |
| #define DSIPHY_LNX_CFG3(n) (0x20C + (0x80 * (n))) |
| #define DSIPHY_LNX_TEST_DATAPATH(n) (0x210 + (0x80 * (n))) |
| #define DSIPHY_LNX_PIN_SWAP(n) (0x214 + (0x80 * (n))) |
| #define DSIPHY_LNX_HSTX_STR_CTRL(n) (0x218 + (0x80 * (n))) |
| #define DSIPHY_LNX_OFFSET_TOP_CTRL(n) (0x21C + (0x80 * (n))) |
| #define DSIPHY_LNX_OFFSET_BOT_CTRL(n) (0x220 + (0x80 * (n))) |
| #define DSIPHY_LNX_LPTX_STR_CTRL(n) (0x224 + (0x80 * (n))) |
| #define DSIPHY_LNX_LPRX_CTRL(n) (0x228 + (0x80 * (n))) |
| #define DSIPHY_LNX_TX_DCTRL(n) (0x22C + (0x80 * (n))) |
| |
| static inline int dsi_conv_phy_to_logical_lane( |
| struct dsi_lane_map *lane_map, enum dsi_phy_data_lanes phy_lane) |
| { |
| int i = 0; |
| |
| if (phy_lane > DSI_PHYSICAL_LANE_3) |
| return -EINVAL; |
| |
| for (i = DSI_LOGICAL_LANE_0; i < (DSI_LANE_MAX - 1); i++) { |
| if (lane_map->lane_map_v2[i] == phy_lane) |
| break; |
| } |
| return i; |
| } |
| |
| static inline int dsi_conv_logical_to_phy_lane( |
| struct dsi_lane_map *lane_map, enum dsi_logical_lane lane) |
| { |
| int i = 0; |
| |
| if (lane > (DSI_LANE_MAX - 1)) |
| return -EINVAL; |
| |
| for (i = DSI_LOGICAL_LANE_0; i < (DSI_LANE_MAX - 1); i++) { |
| if (BIT(i) == lane_map->lane_map_v2[lane]) |
| break; |
| } |
| return i; |
| } |
| |
| /** |
| * regulator_enable() - enable regulators for DSI PHY |
| * @phy: Pointer to DSI PHY hardware object. |
| * @reg_cfg: Regulator configuration for all DSI lanes. |
| */ |
| void dsi_phy_hw_v3_0_regulator_enable(struct dsi_phy_hw *phy, |
| struct dsi_phy_per_lane_cfgs *reg_cfg) |
| { |
| pr_debug("[DSI_%d] Phy regulators enabled\n", phy->index); |
| /* Nothing to be done for DSI PHY regulator enable */ |
| } |
| |
| /** |
| * regulator_disable() - disable regulators |
| * @phy: Pointer to DSI PHY hardware object. |
| */ |
| void dsi_phy_hw_v3_0_regulator_disable(struct dsi_phy_hw *phy) |
| { |
| pr_debug("[DSI_%d] Phy regulators disabled\n", phy->index); |
| /* Nothing to be done for DSI PHY regulator disable */ |
| } |
| |
| |
| static int dsi_phy_hw_v3_0_is_pll_on(struct dsi_phy_hw *phy) |
| { |
| u32 data = 0; |
| |
| data = DSI_R32(phy, DSIPHY_CMN_PLL_CNTRL); |
| mb(); /*make sure read happened */ |
| return (data & BIT(0)); |
| } |
| |
| static void dsi_phy_hw_v3_0_config_lpcdrx(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg, bool enable) |
| { |
| int phy_lane_0 = dsi_conv_logical_to_phy_lane(&cfg->lane_map, |
| DSI_LOGICAL_LANE_0); |
| /* |
| * LPRX and CDRX need to enabled only for physical data lane |
| * corresponding to the logical data lane 0 |
| */ |
| |
| if (enable) |
| DSI_W32(phy, DSIPHY_LNX_LPRX_CTRL(phy_lane_0), |
| cfg->strength.lane[phy_lane_0][1]); |
| else |
| DSI_W32(phy, DSIPHY_LNX_LPRX_CTRL(phy_lane_0), 0); |
| } |
| |
| static void dsi_phy_hw_v3_0_lane_swap_config(struct dsi_phy_hw *phy, |
| struct dsi_lane_map *lane_map) |
| { |
| DSI_W32(phy, DSIPHY_CMN_LANE_CFG0, |
| (lane_map->lane_map_v2[DSI_LOGICAL_LANE_0] | |
| (lane_map->lane_map_v2[DSI_LOGICAL_LANE_1] << 4))); |
| DSI_W32(phy, DSIPHY_CMN_LANE_CFG1, |
| (lane_map->lane_map_v2[DSI_LOGICAL_LANE_2] | |
| (lane_map->lane_map_v2[DSI_LOGICAL_LANE_3] << 4))); |
| } |
| |
| static void dsi_phy_hw_v3_0_lane_settings(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg) |
| { |
| int i; |
| u8 tx_dctrl[] = {0x00, 0x00, 0x00, 0x04, 0x01}; |
| |
| /* Strength ctrl settings */ |
| for (i = DSI_LOGICAL_LANE_0; i < DSI_LANE_MAX; i++) { |
| DSI_W32(phy, DSIPHY_LNX_LPTX_STR_CTRL(i), |
| cfg->strength.lane[i][0]); |
| /* |
| * Disable LPRX and CDRX for all lanes. And later on, it will |
| * be only enabled for the physical data lane corresponding |
| * to the logical data lane 0 |
| */ |
| DSI_W32(phy, DSIPHY_LNX_LPRX_CTRL(i), 0); |
| DSI_W32(phy, DSIPHY_LNX_PIN_SWAP(i), 0x0); |
| DSI_W32(phy, DSIPHY_LNX_HSTX_STR_CTRL(i), 0x88); |
| } |
| dsi_phy_hw_v3_0_config_lpcdrx(phy, cfg, true); |
| |
| /* other settings */ |
| for (i = DSI_LOGICAL_LANE_0; i < DSI_LANE_MAX; i++) { |
| DSI_W32(phy, DSIPHY_LNX_CFG0(i), cfg->lanecfg.lane[i][0]); |
| DSI_W32(phy, DSIPHY_LNX_CFG1(i), cfg->lanecfg.lane[i][1]); |
| DSI_W32(phy, DSIPHY_LNX_CFG2(i), cfg->lanecfg.lane[i][2]); |
| DSI_W32(phy, DSIPHY_LNX_CFG3(i), cfg->lanecfg.lane[i][3]); |
| DSI_W32(phy, DSIPHY_LNX_OFFSET_TOP_CTRL(i), 0x0); |
| DSI_W32(phy, DSIPHY_LNX_OFFSET_BOT_CTRL(i), 0x0); |
| DSI_W32(phy, DSIPHY_LNX_TX_DCTRL(i), tx_dctrl[i]); |
| } |
| |
| /* Toggle BIT 0 to release freeze I/0 */ |
| DSI_W32(phy, DSIPHY_LNX_TX_DCTRL(3), 0x05); |
| DSI_W32(phy, DSIPHY_LNX_TX_DCTRL(3), 0x04); |
| } |
| |
| /** |
| * enable() - Enable PHY hardware |
| * @phy: Pointer to DSI PHY hardware object. |
| * @cfg: Per lane configurations for timing, strength and lane |
| * configurations. |
| */ |
| void dsi_phy_hw_v3_0_enable(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg) |
| { |
| int rc = 0; |
| u32 status; |
| u32 const delay_us = 5; |
| u32 const timeout_us = 1000; |
| struct dsi_phy_per_lane_cfgs *timing = &cfg->timing; |
| u32 data; |
| |
| if (dsi_phy_hw_v3_0_is_pll_on(phy)) |
| pr_warn("PLL turned on before configuring PHY\n"); |
| |
| /* wait for REFGEN READY */ |
| rc = readl_poll_timeout_atomic(phy->base + DSIPHY_CMN_PHY_STATUS, |
| status, (status & BIT(0)), delay_us, timeout_us); |
| if (rc) { |
| pr_err("Ref gen not ready. Aborting\n"); |
| return; |
| } |
| |
| /* de-assert digital and pll power down */ |
| data = BIT(6) | BIT(5); |
| DSI_W32(phy, DSIPHY_CMN_CTRL_0, data); |
| |
| /* Assert PLL core reset */ |
| DSI_W32(phy, DSIPHY_CMN_PLL_CNTRL, 0x00); |
| |
| /* turn off resync FIFO */ |
| DSI_W32(phy, DSIPHY_CMN_RBUF_CTRL, 0x00); |
| |
| /* Select MS1 byte-clk */ |
| DSI_W32(phy, DSIPHY_CMN_GLBL_CTRL, 0x10); |
| |
| /* Enable LDO */ |
| DSI_W32(phy, DSIPHY_CMN_VREG_CTRL, 0x59); |
| |
| /* Configure PHY lane swap */ |
| dsi_phy_hw_v3_0_lane_swap_config(phy, &cfg->lane_map); |
| |
| /* DSI PHY timings */ |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_0, timing->lane_v3[0]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_1, timing->lane_v3[1]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_2, timing->lane_v3[2]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_3, timing->lane_v3[3]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_4, timing->lane_v3[4]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_5, timing->lane_v3[5]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_6, timing->lane_v3[6]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_7, timing->lane_v3[7]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_8, timing->lane_v3[8]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_9, timing->lane_v3[9]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_10, timing->lane_v3[10]); |
| DSI_W32(phy, DSIPHY_CMN_TIMING_CTRL_11, timing->lane_v3[11]); |
| |
| /* Remove power down from all blocks */ |
| DSI_W32(phy, DSIPHY_CMN_CTRL_0, 0x7f); |
| |
| /*power up lanes */ |
| data = DSI_R32(phy, DSIPHY_CMN_CTRL_0); |
| /* TODO: only power up lanes that are used */ |
| data |= 0x1F; |
| DSI_W32(phy, DSIPHY_CMN_CTRL_0, data); |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL0, 0x1F); |
| |
| /* Select full-rate mode */ |
| DSI_W32(phy, DSIPHY_CMN_CTRL_2, 0x40); |
| |
| switch (cfg->pll_source) { |
| case DSI_PLL_SOURCE_STANDALONE: |
| case DSI_PLL_SOURCE_NATIVE: |
| data = 0x0; /* internal PLL */ |
| break; |
| case DSI_PLL_SOURCE_NON_NATIVE: |
| data = 0x1; /* external PLL */ |
| break; |
| default: |
| break; |
| } |
| DSI_W32(phy, DSIPHY_CMN_CLK_CFG1, (data << 2)); /* set PLL src */ |
| |
| /* DSI lane settings */ |
| dsi_phy_hw_v3_0_lane_settings(phy, cfg); |
| |
| pr_debug("[DSI_%d]Phy enabled ", phy->index); |
| } |
| |
| /** |
| * disable() - Disable PHY hardware |
| * @phy: Pointer to DSI PHY hardware object. |
| */ |
| void dsi_phy_hw_v3_0_disable(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg) |
| { |
| u32 data = 0; |
| |
| if (dsi_phy_hw_v3_0_is_pll_on(phy)) |
| pr_warn("Turning OFF PHY while PLL is on\n"); |
| |
| dsi_phy_hw_v3_0_config_lpcdrx(phy, cfg, false); |
| |
| data = DSI_R32(phy, DSIPHY_CMN_CTRL_0); |
| /* disable all lanes */ |
| data &= ~0x1F; |
| DSI_W32(phy, DSIPHY_CMN_CTRL_0, data); |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL0, 0); |
| |
| /* Turn off all PHY blocks */ |
| DSI_W32(phy, DSIPHY_CMN_CTRL_0, 0x00); |
| /* make sure phy is turned off */ |
| wmb(); |
| pr_debug("[DSI_%d]Phy disabled ", phy->index); |
| } |
| |
| int dsi_phy_hw_v3_0_wait_for_lane_idle( |
| struct dsi_phy_hw *phy, u32 lanes) |
| { |
| int rc = 0, val = 0; |
| u32 stop_state_mask = 0; |
| u32 const sleep_us = 10; |
| u32 const timeout_us = 100; |
| |
| stop_state_mask = BIT(4); /* clock lane */ |
| if (lanes & DSI_DATA_LANE_0) |
| stop_state_mask |= BIT(0); |
| if (lanes & DSI_DATA_LANE_1) |
| stop_state_mask |= BIT(1); |
| if (lanes & DSI_DATA_LANE_2) |
| stop_state_mask |= BIT(2); |
| if (lanes & DSI_DATA_LANE_3) |
| stop_state_mask |= BIT(3); |
| |
| pr_debug("%s: polling for lanes to be in stop state, mask=0x%08x\n", |
| __func__, stop_state_mask); |
| rc = readl_poll_timeout(phy->base + DSIPHY_CMN_LANE_STATUS1, val, |
| (val == stop_state_mask), sleep_us, timeout_us); |
| if (rc) { |
| pr_err("%s: lanes not in stop state, LANE_STATUS=0x%08x\n", |
| __func__, val); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| void dsi_phy_hw_v3_0_ulps_request(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg, u32 lanes) |
| { |
| u32 reg = 0; |
| |
| if (lanes & DSI_CLOCK_LANE) |
| reg = BIT(4); |
| if (lanes & DSI_DATA_LANE_0) |
| reg |= BIT(0); |
| if (lanes & DSI_DATA_LANE_1) |
| reg |= BIT(1); |
| if (lanes & DSI_DATA_LANE_2) |
| reg |= BIT(2); |
| if (lanes & DSI_DATA_LANE_3) |
| reg |= BIT(3); |
| |
| /* |
| * ULPS entry request. Wait for short time to make sure |
| * that the lanes enter ULPS. Recommended as per HPG. |
| */ |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL1, reg); |
| usleep_range(100, 110); |
| |
| /* disable LPRX and CDRX */ |
| dsi_phy_hw_v3_0_config_lpcdrx(phy, cfg, false); |
| /* disable lane LDOs */ |
| DSI_W32(phy, DSIPHY_CMN_VREG_CTRL, 0x19); |
| pr_debug("[DSI_PHY%d] ULPS requested for lanes 0x%x\n", phy->index, |
| lanes); |
| } |
| |
| void dsi_phy_hw_v3_0_ulps_exit(struct dsi_phy_hw *phy, |
| struct dsi_phy_cfg *cfg, u32 lanes) |
| { |
| u32 reg = 0; |
| |
| if (lanes & DSI_CLOCK_LANE) |
| reg = BIT(4); |
| if (lanes & DSI_DATA_LANE_0) |
| reg |= BIT(0); |
| if (lanes & DSI_DATA_LANE_1) |
| reg |= BIT(1); |
| if (lanes & DSI_DATA_LANE_2) |
| reg |= BIT(2); |
| if (lanes & DSI_DATA_LANE_3) |
| reg |= BIT(3); |
| |
| /* enable lane LDOs */ |
| DSI_W32(phy, DSIPHY_CMN_VREG_CTRL, 0x59); |
| /* enable LPRX and CDRX */ |
| dsi_phy_hw_v3_0_config_lpcdrx(phy, cfg, true); |
| |
| /* ULPS exit request */ |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL2, reg); |
| usleep_range(1000, 1010); |
| |
| /* Clear ULPS request flags on all lanes */ |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL1, 0); |
| /* Clear ULPS exit flags on all lanes */ |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL2, 0); |
| |
| /* |
| * Sometimes when exiting ULPS, it is possible that some DSI |
| * lanes are not in the stop state which could lead to DSI |
| * commands not going through. To avoid this, force the lanes |
| * to be in stop state. |
| */ |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL3, reg); |
| DSI_W32(phy, DSIPHY_CMN_LANE_CTRL3, 0); |
| usleep_range(100, 110); |
| } |
| |
| u32 dsi_phy_hw_v3_0_get_lanes_in_ulps(struct dsi_phy_hw *phy) |
| { |
| u32 lanes = 0; |
| |
| lanes = DSI_R32(phy, DSIPHY_CMN_LANE_STATUS0); |
| pr_debug("[DSI_PHY%d] lanes in ulps = 0x%x\n", phy->index, lanes); |
| return lanes; |
| } |
| |
| int dsi_phy_hw_timing_val_v3_0(struct dsi_phy_per_lane_cfgs *timing_cfg, |
| u32 *timing_val, u32 size) |
| { |
| int i = 0; |
| |
| if (size != DSI_PHY_TIMING_V3_SIZE) { |
| pr_err("Unexpected timing array size %d\n", size); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < size; i++) |
| timing_cfg->lane_v3[i] = timing_val[i]; |
| return 0; |
| } |