| QPNP OLEDB (AMOLED AVDD Bias) Regulator |
| |
| QPNP OLEDB module provides AVDD voltage bias to the AMOLED display panel. |
| The supported voltage range is 5V to 8.1V. |
| |
| This document describes the bindings for QPNP OLEDB module. |
| |
| ======================= |
| Required Node Structure |
| ======================= |
| |
| - compatible |
| Usage: required |
| Value type: <string> |
| Definition: should be "qcom,qpnp-oledb-regulator". |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: Base address of the OLEDB SPMI peripheral. |
| |
| - label |
| Usage: required |
| Value type: <string> |
| Definition: A string used to describe the bias type(oledb). |
| |
| - regulator-name |
| Usage: required |
| Value type: <string> |
| Definition: A string used to describe the regulator. |
| |
| - regulator-min-microvolt |
| Usage: required |
| Value type: <u32> |
| Definition: Minimum voltage (in uV) supported by the bias (5000000uV). |
| |
| - regulator-max-microvolt |
| Usage: required |
| Value type: <u32> |
| Definition: Maximum voltage (in uV) supported by the bias (8100000uV). |
| |
| - qcom,swire-control |
| Usage: optional |
| Value type: <bool> |
| Definition: Enables the voltage programming through SWIRE signal. |
| |
| qcom,ext-pin-control |
| Usage: optional |
| Value type: <bool> |
| Definition: Configures the OLED module to be enabled by a external pin. |
| |
| qcom,dynamic-ext-pinctl-config |
| Usage: optional |
| Value type: <bool> |
| Definition: Used to dynamically enable/disable the OLEDB module |
| using external pin to avoid the glitches on the voltage |
| rail. This property is applicable only if qcom,ext-pin-ctl |
| property is specified and it is specific to PM660A. |
| |
| qcom,pbs-control |
| Usage: optional |
| Value type: <bool> |
| Definition: PMIC PBS logic directly configures the output voltage update |
| and pull down control. |
| |
| qcom,oledb-init-voltage-mv |
| Usage: optional |
| Value type: <u32> |
| Definition: Sets the AVDD bias voltage (in mV) when the module is |
| already enabled. Applicable only if the qcom,swire-control |
| property is not specified. Supported values are from 5.0V |
| to 8.1V with a step of 100mV. |
| |
| qcom,oledb-default-voltage-mv |
| Usage: optional |
| Value type: <u32> |
| Definition: Sets the default AVDD bias voltage (in mV) before module |
| enable. Supported values are from 5.0V to 8.1V with the |
| step of 100mV. |
| |
| qcom,bias-gen-warmup-delay-ns |
| Usage: optional |
| Value type: <u32> |
| Definition: Bias generator warm-up time (ns). Supported values are |
| 6700, 13300, 267000, 534000. |
| |
| qcom,peak-curr-limit-ma |
| Usage: optional |
| Value type: <u32> |
| Definition: Peak current limit (in mA). Supported values are 115, 265, |
| 415, 570, 720, 870, 1020, 1170. |
| |
| qcom,pull-down-enable |
| Usage: optional |
| Value type: <u32> |
| Definition: Pull down configuration of OLEDB. |
| 1 - Enable pull-down |
| 0 - Disable pull-down |
| |
| qcom,negative-curr-limit-enable |
| Usage: optional |
| Value type: <u32> |
| Definition: negative current limit enable/disable. |
| 1 = enable negative current limit |
| 0 = disable negative current limit |
| |
| qcom,negative-curr-limit-ma |
| Usage: optional |
| Value type: <u32> |
| Definition: Negative current limit (in mA). Supported values are |
| 170, 300, 420, 550. |
| |
| qcom,enable-short-circuit |
| Usage: optional |
| Value type: <u32> |
| Definition: Short circuit protection enable/disable. |
| 1 = enable short circuit protection |
| 0 = disable short circuit protection |
| |
| qcom,short-circuit-dbnc-time |
| usage: optional |
| Value type: <u32> |
| Definitioan: Short circuit debounce time (in Fsw). Supported |
| values are 2, 4, 8, 16. |
| |
| Fast precharge properties: |
| ------------------------- |
| |
| qcom,fast-precharge-ppulse-enable |
| usage: optional |
| Value type: <u32> |
| Definitioan: Fast precharge pfet pulsing enable/disable. |
| 1 = enable fast precharge pfet pulsing |
| 0 = disable fast precharge pfet pulsing |
| |
| qcom,precharge-debounce-time-ms |
| usage: optional |
| Value type: <u32> |
| Definitioan: Fast precharge debounce time (in ms). Supported |
| values are 1, 2, 4, 8. |
| |
| qcom,precharge-pulse-period-us |
| usage: optional |
| Value type: <u32> |
| Definitioan: Fast precharge pulse period (in us). Supported |
| values are 3, 6, 9, 12. |
| |
| qcom,precharge-pulse-on-time-us |
| usage: optional |
| Value type: <u32> |
| Definitioan: Fast precharge pulse on time (in ns). Supported |
| values are 1200, 1800, 2400, 3000. |
| |
| Pulse Skip Modulation (PSM) properties: |
| -------------------------------------- |
| |
| qcom,psm-enable |
| Usage: optional |
| Value type: <u32> |
| Definition: Pulse Skip Modulation mode. |
| 1 - Enable PSM mode |
| 0 - Disable PSM mode |
| |
| qcom,psm-hys-mv |
| Usage: optional |
| Value type: <u32> |
| Definition: PSM hysterysis voltage (in mV). |
| Supported values are 13mV and 26mV. |
| |
| qcom,psm-vref-mv |
| Usage: optional |
| Value type: <u32> |
| Definition: Reference voltage(in mV) control for PSM comparator. |
| Supported values are 440, 510, 580, 650, 715, 780, 850, |
| and 920. |
| |
| Pulse Frequency Modulation (PFM) properties: |
| ------------------------------------------- |
| |
| qcom,pfm-enable |
| Usage: optional |
| Value type: <u32> |
| Definition: Pulse Frequency Modulation mode. |
| 1 - Enable PFM mode |
| 0 - Disable PFM mode |
| |
| qcom,pfm-hys-mv |
| Usage: optional |
| Value type: <u32> |
| Definition: PFM hysterysis voltage (in mV). |
| Supported values are 13mV and 26mV. |
| |
| qcom,pfm-curr-limit-ma |
| Usage: optional |
| Value type: <u32> |
| Definition: PFM current limit (in mA). |
| Supported values are 130, 200, 270, 340. |
| |
| qcom,pfm-off-time-ns |
| Usage: optional |
| Value type: <u32> |
| Definition: NFET off time at PFM (in ns). |
| Supported values are 110, 240, 350, 480. |
| |
| ======= |
| Example |
| ======= |
| |
| pm660a_oledb: qpnp-oledb@e000 { |
| compatible = "qcom,qpnp-oledb-regulator"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0xe000 0x100>; |
| |
| label = "oledb"; |
| regulator-name = "regulator-oledb"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <8100000>; |
| |
| qcom,swire-control; |
| qcom,ext-pin-control; |
| |
| qcom,oledb-default-voltage-mv = <5000>; |
| qcom,bias-gen-warmup-delay-ns = <6700>; |
| qcom,pull-down-enable = <1>; |
| qcom,peak-curr-limit-ma = <570>; |
| |
| qcom, enable-psm = <1>; |
| qcom,psm-hys-mv = <13>; |
| }; |