| /* |
| * Davicom DM9601 USB 1.1 10/100Mbps ethernet devices |
| * |
| * Peter Korsgaard <jacmet@sunsite.dk> |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| //#define DEBUG |
| |
| #include <linux/module.h> |
| #include <linux/sched.h> |
| #include <linux/stddef.h> |
| #include <linux/init.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/ethtool.h> |
| #include <linux/mii.h> |
| #include <linux/usb.h> |
| #include <linux/crc32.h> |
| #include <linux/usb/usbnet.h> |
| #include <linux/slab.h> |
| |
| /* datasheet: |
| http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf |
| */ |
| |
| /* control requests */ |
| #define DM_READ_REGS 0x00 |
| #define DM_WRITE_REGS 0x01 |
| #define DM_READ_MEMS 0x02 |
| #define DM_WRITE_REG 0x03 |
| #define DM_WRITE_MEMS 0x05 |
| #define DM_WRITE_MEM 0x07 |
| |
| /* registers */ |
| #define DM_NET_CTRL 0x00 |
| #define DM_RX_CTRL 0x05 |
| #define DM_SHARED_CTRL 0x0b |
| #define DM_SHARED_ADDR 0x0c |
| #define DM_SHARED_DATA 0x0d /* low + high */ |
| #define DM_PHY_ADDR 0x10 /* 6 bytes */ |
| #define DM_MCAST_ADDR 0x16 /* 8 bytes */ |
| #define DM_GPR_CTRL 0x1e |
| #define DM_GPR_DATA 0x1f |
| |
| #define DM_MAX_MCAST 64 |
| #define DM_MCAST_SIZE 8 |
| #define DM_EEPROM_LEN 256 |
| #define DM_TX_OVERHEAD 2 /* 2 byte header */ |
| #define DM_RX_OVERHEAD 7 /* 3 byte header + 4 byte crc tail */ |
| #define DM_TIMEOUT 1000 |
| |
| |
| static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data) |
| { |
| void *buf; |
| int err = -ENOMEM; |
| |
| netdev_dbg(dev->net, "dm_read() reg=0x%02x length=%d\n", reg, length); |
| |
| buf = kmalloc(length, GFP_KERNEL); |
| if (!buf) |
| goto out; |
| |
| err = usb_control_msg(dev->udev, |
| usb_rcvctrlpipe(dev->udev, 0), |
| DM_READ_REGS, |
| USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, |
| 0, reg, buf, length, USB_CTRL_SET_TIMEOUT); |
| if (err == length) |
| memcpy(data, buf, length); |
| else if (err >= 0) |
| err = -EINVAL; |
| kfree(buf); |
| |
| out: |
| return err; |
| } |
| |
| static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value) |
| { |
| return dm_read(dev, reg, 1, value); |
| } |
| |
| static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data) |
| { |
| void *buf = NULL; |
| int err = -ENOMEM; |
| |
| netdev_dbg(dev->net, "dm_write() reg=0x%02x, length=%d\n", reg, length); |
| |
| if (data) { |
| buf = kmemdup(data, length, GFP_KERNEL); |
| if (!buf) |
| goto out; |
| } |
| |
| err = usb_control_msg(dev->udev, |
| usb_sndctrlpipe(dev->udev, 0), |
| DM_WRITE_REGS, |
| USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE, |
| 0, reg, buf, length, USB_CTRL_SET_TIMEOUT); |
| kfree(buf); |
| if (err >= 0 && err < length) |
| err = -EINVAL; |
| out: |
| return err; |
| } |
| |
| static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value) |
| { |
| netdev_dbg(dev->net, "dm_write_reg() reg=0x%02x, value=0x%02x\n", |
| reg, value); |
| return usb_control_msg(dev->udev, |
| usb_sndctrlpipe(dev->udev, 0), |
| DM_WRITE_REG, |
| USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE, |
| value, reg, NULL, 0, USB_CTRL_SET_TIMEOUT); |
| } |
| |
| static void dm_write_async_callback(struct urb *urb) |
| { |
| struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context; |
| int status = urb->status; |
| |
| if (status < 0) |
| printk(KERN_DEBUG "dm_write_async_callback() failed with %d\n", |
| status); |
| |
| kfree(req); |
| usb_free_urb(urb); |
| } |
| |
| static void dm_write_async_helper(struct usbnet *dev, u8 reg, u8 value, |
| u16 length, void *data) |
| { |
| struct usb_ctrlrequest *req; |
| struct urb *urb; |
| int status; |
| |
| urb = usb_alloc_urb(0, GFP_ATOMIC); |
| if (!urb) { |
| netdev_err(dev->net, "Error allocating URB in dm_write_async_helper!\n"); |
| return; |
| } |
| |
| req = kmalloc(sizeof(struct usb_ctrlrequest), GFP_ATOMIC); |
| if (!req) { |
| netdev_err(dev->net, "Failed to allocate memory for control request\n"); |
| usb_free_urb(urb); |
| return; |
| } |
| |
| req->bRequestType = USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE; |
| req->bRequest = length ? DM_WRITE_REGS : DM_WRITE_REG; |
| req->wValue = cpu_to_le16(value); |
| req->wIndex = cpu_to_le16(reg); |
| req->wLength = cpu_to_le16(length); |
| |
| usb_fill_control_urb(urb, dev->udev, |
| usb_sndctrlpipe(dev->udev, 0), |
| (void *)req, data, length, |
| dm_write_async_callback, req); |
| |
| status = usb_submit_urb(urb, GFP_ATOMIC); |
| if (status < 0) { |
| netdev_err(dev->net, "Error submitting the control message: status=%d\n", |
| status); |
| kfree(req); |
| usb_free_urb(urb); |
| } |
| } |
| |
| static void dm_write_async(struct usbnet *dev, u8 reg, u16 length, void *data) |
| { |
| netdev_dbg(dev->net, "dm_write_async() reg=0x%02x length=%d\n", reg, length); |
| |
| dm_write_async_helper(dev, reg, 0, length, data); |
| } |
| |
| static void dm_write_reg_async(struct usbnet *dev, u8 reg, u8 value) |
| { |
| netdev_dbg(dev->net, "dm_write_reg_async() reg=0x%02x value=0x%02x\n", |
| reg, value); |
| |
| dm_write_async_helper(dev, reg, value, 0, NULL); |
| } |
| |
| static int dm_read_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 *value) |
| { |
| int ret, i; |
| |
| mutex_lock(&dev->phy_mutex); |
| |
| dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); |
| dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0xc : 0x4); |
| |
| for (i = 0; i < DM_TIMEOUT; i++) { |
| u8 tmp; |
| |
| udelay(1); |
| ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); |
| if (ret < 0) |
| goto out; |
| |
| /* ready */ |
| if ((tmp & 1) == 0) |
| break; |
| } |
| |
| if (i == DM_TIMEOUT) { |
| netdev_err(dev->net, "%s read timed out!\n", phy ? "phy" : "eeprom"); |
| ret = -EIO; |
| goto out; |
| } |
| |
| dm_write_reg(dev, DM_SHARED_CTRL, 0x0); |
| ret = dm_read(dev, DM_SHARED_DATA, 2, value); |
| |
| netdev_dbg(dev->net, "read shared %d 0x%02x returned 0x%04x, %d\n", |
| phy, reg, *value, ret); |
| |
| out: |
| mutex_unlock(&dev->phy_mutex); |
| return ret; |
| } |
| |
| static int dm_write_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 value) |
| { |
| int ret, i; |
| |
| mutex_lock(&dev->phy_mutex); |
| |
| ret = dm_write(dev, DM_SHARED_DATA, 2, &value); |
| if (ret < 0) |
| goto out; |
| |
| dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); |
| dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0x1a : 0x12); |
| |
| for (i = 0; i < DM_TIMEOUT; i++) { |
| u8 tmp; |
| |
| udelay(1); |
| ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); |
| if (ret < 0) |
| goto out; |
| |
| /* ready */ |
| if ((tmp & 1) == 0) |
| break; |
| } |
| |
| if (i == DM_TIMEOUT) { |
| netdev_err(dev->net, "%s write timed out!\n", phy ? "phy" : "eeprom"); |
| ret = -EIO; |
| goto out; |
| } |
| |
| dm_write_reg(dev, DM_SHARED_CTRL, 0x0); |
| |
| out: |
| mutex_unlock(&dev->phy_mutex); |
| return ret; |
| } |
| |
| static int dm_read_eeprom_word(struct usbnet *dev, u8 offset, void *value) |
| { |
| return dm_read_shared_word(dev, 0, offset, value); |
| } |
| |
| |
| |
| static int dm9601_get_eeprom_len(struct net_device *dev) |
| { |
| return DM_EEPROM_LEN; |
| } |
| |
| static int dm9601_get_eeprom(struct net_device *net, |
| struct ethtool_eeprom *eeprom, u8 * data) |
| { |
| struct usbnet *dev = netdev_priv(net); |
| __le16 *ebuf = (__le16 *) data; |
| int i; |
| |
| /* access is 16bit */ |
| if ((eeprom->offset % 2) || (eeprom->len % 2)) |
| return -EINVAL; |
| |
| for (i = 0; i < eeprom->len / 2; i++) { |
| if (dm_read_eeprom_word(dev, eeprom->offset / 2 + i, |
| &ebuf[i]) < 0) |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static int dm9601_mdio_read(struct net_device *netdev, int phy_id, int loc) |
| { |
| struct usbnet *dev = netdev_priv(netdev); |
| |
| __le16 res; |
| |
| if (phy_id) { |
| netdev_dbg(dev->net, "Only internal phy supported\n"); |
| return 0; |
| } |
| |
| dm_read_shared_word(dev, 1, loc, &res); |
| |
| netdev_dbg(dev->net, |
| "dm9601_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n", |
| phy_id, loc, le16_to_cpu(res)); |
| |
| return le16_to_cpu(res); |
| } |
| |
| static void dm9601_mdio_write(struct net_device *netdev, int phy_id, int loc, |
| int val) |
| { |
| struct usbnet *dev = netdev_priv(netdev); |
| __le16 res = cpu_to_le16(val); |
| |
| if (phy_id) { |
| netdev_dbg(dev->net, "Only internal phy supported\n"); |
| return; |
| } |
| |
| netdev_dbg(dev->net, "dm9601_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n", |
| phy_id, loc, val); |
| |
| dm_write_shared_word(dev, 1, loc, res); |
| } |
| |
| static void dm9601_get_drvinfo(struct net_device *net, |
| struct ethtool_drvinfo *info) |
| { |
| /* Inherit standard device info */ |
| usbnet_get_drvinfo(net, info); |
| info->eedump_len = DM_EEPROM_LEN; |
| } |
| |
| static u32 dm9601_get_link(struct net_device *net) |
| { |
| struct usbnet *dev = netdev_priv(net); |
| |
| return mii_link_ok(&dev->mii); |
| } |
| |
| static int dm9601_ioctl(struct net_device *net, struct ifreq *rq, int cmd) |
| { |
| struct usbnet *dev = netdev_priv(net); |
| |
| return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL); |
| } |
| |
| static const struct ethtool_ops dm9601_ethtool_ops = { |
| .get_drvinfo = dm9601_get_drvinfo, |
| .get_link = dm9601_get_link, |
| .get_msglevel = usbnet_get_msglevel, |
| .set_msglevel = usbnet_set_msglevel, |
| .get_eeprom_len = dm9601_get_eeprom_len, |
| .get_eeprom = dm9601_get_eeprom, |
| .get_settings = usbnet_get_settings, |
| .set_settings = usbnet_set_settings, |
| .nway_reset = usbnet_nway_reset, |
| }; |
| |
| static void dm9601_set_multicast(struct net_device *net) |
| { |
| struct usbnet *dev = netdev_priv(net); |
| /* We use the 20 byte dev->data for our 8 byte filter buffer |
| * to avoid allocating memory that is tricky to free later */ |
| u8 *hashes = (u8 *) & dev->data; |
| u8 rx_ctl = 0x31; |
| |
| memset(hashes, 0x00, DM_MCAST_SIZE); |
| hashes[DM_MCAST_SIZE - 1] |= 0x80; /* broadcast address */ |
| |
| if (net->flags & IFF_PROMISC) { |
| rx_ctl |= 0x02; |
| } else if (net->flags & IFF_ALLMULTI || |
| netdev_mc_count(net) > DM_MAX_MCAST) { |
| rx_ctl |= 0x04; |
| } else if (!netdev_mc_empty(net)) { |
| struct netdev_hw_addr *ha; |
| |
| netdev_for_each_mc_addr(ha, net) { |
| u32 crc = ether_crc(ETH_ALEN, ha->addr) >> 26; |
| hashes[crc >> 3] |= 1 << (crc & 0x7); |
| } |
| } |
| |
| dm_write_async(dev, DM_MCAST_ADDR, DM_MCAST_SIZE, hashes); |
| dm_write_reg_async(dev, DM_RX_CTRL, rx_ctl); |
| } |
| |
| static void __dm9601_set_mac_address(struct usbnet *dev) |
| { |
| dm_write_async(dev, DM_PHY_ADDR, ETH_ALEN, dev->net->dev_addr); |
| } |
| |
| static int dm9601_set_mac_address(struct net_device *net, void *p) |
| { |
| struct sockaddr *addr = p; |
| struct usbnet *dev = netdev_priv(net); |
| |
| if (!is_valid_ether_addr(addr->sa_data)) { |
| dev_err(&net->dev, "not setting invalid mac address %pM\n", |
| addr->sa_data); |
| return -EINVAL; |
| } |
| |
| memcpy(net->dev_addr, addr->sa_data, net->addr_len); |
| __dm9601_set_mac_address(dev); |
| |
| return 0; |
| } |
| |
| static const struct net_device_ops dm9601_netdev_ops = { |
| .ndo_open = usbnet_open, |
| .ndo_stop = usbnet_stop, |
| .ndo_start_xmit = usbnet_start_xmit, |
| .ndo_tx_timeout = usbnet_tx_timeout, |
| .ndo_change_mtu = usbnet_change_mtu, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_do_ioctl = dm9601_ioctl, |
| .ndo_set_rx_mode = dm9601_set_multicast, |
| .ndo_set_mac_address = dm9601_set_mac_address, |
| }; |
| |
| static int dm9601_bind(struct usbnet *dev, struct usb_interface *intf) |
| { |
| int ret; |
| u8 mac[ETH_ALEN]; |
| |
| ret = usbnet_get_endpoints(dev, intf); |
| if (ret) |
| goto out; |
| |
| dev->net->netdev_ops = &dm9601_netdev_ops; |
| dev->net->ethtool_ops = &dm9601_ethtool_ops; |
| dev->net->hard_header_len += DM_TX_OVERHEAD; |
| dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; |
| dev->rx_urb_size = dev->net->mtu + ETH_HLEN + DM_RX_OVERHEAD; |
| |
| dev->mii.dev = dev->net; |
| dev->mii.mdio_read = dm9601_mdio_read; |
| dev->mii.mdio_write = dm9601_mdio_write; |
| dev->mii.phy_id_mask = 0x1f; |
| dev->mii.reg_num_mask = 0x1f; |
| |
| /* reset */ |
| dm_write_reg(dev, DM_NET_CTRL, 1); |
| udelay(20); |
| |
| /* read MAC */ |
| if (dm_read(dev, DM_PHY_ADDR, ETH_ALEN, mac) < 0) { |
| printk(KERN_ERR "Error reading MAC address\n"); |
| ret = -ENODEV; |
| goto out; |
| } |
| |
| /* |
| * Overwrite the auto-generated address only with good ones. |
| */ |
| if (is_valid_ether_addr(mac)) |
| memcpy(dev->net->dev_addr, mac, ETH_ALEN); |
| else { |
| printk(KERN_WARNING |
| "dm9601: No valid MAC address in EEPROM, using %pM\n", |
| dev->net->dev_addr); |
| __dm9601_set_mac_address(dev); |
| } |
| |
| /* power up phy */ |
| dm_write_reg(dev, DM_GPR_CTRL, 1); |
| dm_write_reg(dev, DM_GPR_DATA, 0); |
| |
| /* receive broadcast packets */ |
| dm9601_set_multicast(dev->net); |
| |
| dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET); |
| dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, |
| ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); |
| mii_nway_restart(&dev->mii); |
| |
| out: |
| return ret; |
| } |
| |
| static int dm9601_rx_fixup(struct usbnet *dev, struct sk_buff *skb) |
| { |
| u8 status; |
| int len; |
| |
| /* format: |
| b1: rx status |
| b2: packet length (incl crc) low |
| b3: packet length (incl crc) high |
| b4..n-4: packet data |
| bn-3..bn: ethernet crc |
| */ |
| |
| if (unlikely(skb->len < DM_RX_OVERHEAD)) { |
| dev_err(&dev->udev->dev, "unexpected tiny rx frame\n"); |
| return 0; |
| } |
| |
| status = skb->data[0]; |
| len = (skb->data[1] | (skb->data[2] << 8)) - 4; |
| |
| if (unlikely(status & 0xbf)) { |
| if (status & 0x01) dev->net->stats.rx_fifo_errors++; |
| if (status & 0x02) dev->net->stats.rx_crc_errors++; |
| if (status & 0x04) dev->net->stats.rx_frame_errors++; |
| if (status & 0x20) dev->net->stats.rx_missed_errors++; |
| if (status & 0x90) dev->net->stats.rx_length_errors++; |
| return 0; |
| } |
| |
| skb_pull(skb, 3); |
| skb_trim(skb, len); |
| |
| return 1; |
| } |
| |
| static struct sk_buff *dm9601_tx_fixup(struct usbnet *dev, struct sk_buff *skb, |
| gfp_t flags) |
| { |
| int len; |
| |
| /* format: |
| b1: packet length low |
| b2: packet length high |
| b3..n: packet data |
| */ |
| |
| len = skb->len; |
| |
| if (skb_headroom(skb) < DM_TX_OVERHEAD) { |
| struct sk_buff *skb2; |
| |
| skb2 = skb_copy_expand(skb, DM_TX_OVERHEAD, 0, flags); |
| dev_kfree_skb_any(skb); |
| skb = skb2; |
| if (!skb) |
| return NULL; |
| } |
| |
| __skb_push(skb, DM_TX_OVERHEAD); |
| |
| /* usbnet adds padding if length is a multiple of packet size |
| if so, adjust length value in header */ |
| if ((skb->len % dev->maxpacket) == 0) |
| len++; |
| |
| skb->data[0] = len; |
| skb->data[1] = len >> 8; |
| |
| return skb; |
| } |
| |
| static void dm9601_status(struct usbnet *dev, struct urb *urb) |
| { |
| int link; |
| u8 *buf; |
| |
| /* format: |
| b0: net status |
| b1: tx status 1 |
| b2: tx status 2 |
| b3: rx status |
| b4: rx overflow |
| b5: rx count |
| b6: tx count |
| b7: gpr |
| */ |
| |
| if (urb->actual_length < 8) |
| return; |
| |
| buf = urb->transfer_buffer; |
| |
| link = !!(buf[0] & 0x40); |
| if (netif_carrier_ok(dev->net) != link) { |
| if (link) { |
| netif_carrier_on(dev->net); |
| usbnet_defer_kevent (dev, EVENT_LINK_RESET); |
| } |
| else |
| netif_carrier_off(dev->net); |
| netdev_dbg(dev->net, "Link Status is: %d\n", link); |
| } |
| } |
| |
| static int dm9601_link_reset(struct usbnet *dev) |
| { |
| struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; |
| |
| mii_check_media(&dev->mii, 1, 1); |
| mii_ethtool_gset(&dev->mii, &ecmd); |
| |
| netdev_dbg(dev->net, "link_reset() speed: %u duplex: %d\n", |
| ethtool_cmd_speed(&ecmd), ecmd.duplex); |
| |
| return 0; |
| } |
| |
| static const struct driver_info dm9601_info = { |
| .description = "Davicom DM9601 USB Ethernet", |
| .flags = FLAG_ETHER | FLAG_LINK_INTR, |
| .bind = dm9601_bind, |
| .rx_fixup = dm9601_rx_fixup, |
| .tx_fixup = dm9601_tx_fixup, |
| .status = dm9601_status, |
| .link_reset = dm9601_link_reset, |
| .reset = dm9601_link_reset, |
| }; |
| |
| static const struct usb_device_id products[] = { |
| { |
| USB_DEVICE(0x07aa, 0x9601), /* Corega FEther USB-TXC */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a46, 0x9601), /* Davicom USB-100 */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a46, 0x6688), /* ZT6688 USB NIC */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a46, 0x0268), /* ShanTou ST268 USB NIC */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a46, 0x8515), /* ADMtek ADM8515 USB NIC */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a47, 0x9601), /* Hirose USB-100 */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0fe6, 0x8101), /* DM9601 USB to Fast Ethernet Adapter */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0fe6, 0x9700), /* DM9601 USB to Fast Ethernet Adapter */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| { |
| USB_DEVICE(0x0a46, 0x9000), /* DM9000E */ |
| .driver_info = (unsigned long)&dm9601_info, |
| }, |
| {}, // END |
| }; |
| |
| MODULE_DEVICE_TABLE(usb, products); |
| |
| static struct usb_driver dm9601_driver = { |
| .name = "dm9601", |
| .id_table = products, |
| .probe = usbnet_probe, |
| .disconnect = usbnet_disconnect, |
| .suspend = usbnet_suspend, |
| .resume = usbnet_resume, |
| }; |
| |
| module_usb_driver(dm9601_driver); |
| |
| MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>"); |
| MODULE_DESCRIPTION("Davicom DM9601 USB 1.1 ethernet devices"); |
| MODULE_LICENSE("GPL"); |