| /* |
| * Copyright 2007-2008 Analog Devices Inc. |
| * |
| * Licensed under the ADI BSD license or the GPL-2 (or later) |
| */ |
| |
| #ifndef _DEF_BF525_H |
| #define _DEF_BF525_H |
| |
| /* Include all Core registers and bit definitions */ |
| #include <asm/def_LPBlackfin.h> |
| |
| /* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF525 */ |
| |
| /* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */ |
| #include "defBF52x_base.h" |
| |
| /* The following are the #defines needed by ADSP-BF525 that are not in the common header */ |
| |
| /* USB Control Registers */ |
| |
| #define USB_FADDR 0xffc03800 /* Function address register */ |
| #define USB_POWER 0xffc03804 /* Power management register */ |
| #define USB_INTRTX 0xffc03808 /* Interrupt register for endpoint 0 and Tx endpoint 1 to 7 */ |
| #define USB_INTRRX 0xffc0380c /* Interrupt register for Rx endpoints 1 to 7 */ |
| #define USB_INTRTXE 0xffc03810 /* Interrupt enable register for IntrTx */ |
| #define USB_INTRRXE 0xffc03814 /* Interrupt enable register for IntrRx */ |
| #define USB_INTRUSB 0xffc03818 /* Interrupt register for common USB interrupts */ |
| #define USB_INTRUSBE 0xffc0381c /* Interrupt enable register for IntrUSB */ |
| #define USB_FRAME 0xffc03820 /* USB frame number */ |
| #define USB_INDEX 0xffc03824 /* Index register for selecting the indexed endpoint registers */ |
| #define USB_TESTMODE 0xffc03828 /* Enabled USB 20 test modes */ |
| #define USB_GLOBINTR 0xffc0382c /* Global Interrupt Mask register and Wakeup Exception Interrupt */ |
| #define USB_GLOBAL_CTL 0xffc03830 /* Global Clock Control for the core */ |
| |
| /* USB Packet Control Registers */ |
| |
| #define USB_TX_MAX_PACKET 0xffc03840 /* Maximum packet size for Host Tx endpoint */ |
| #define USB_CSR0 0xffc03844 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */ |
| #define USB_TXCSR 0xffc03844 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */ |
| #define USB_RX_MAX_PACKET 0xffc03848 /* Maximum packet size for Host Rx endpoint */ |
| #define USB_RXCSR 0xffc0384c /* Control Status register for Host Rx endpoint */ |
| #define USB_COUNT0 0xffc03850 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */ |
| #define USB_RXCOUNT 0xffc03850 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */ |
| #define USB_TXTYPE 0xffc03854 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint */ |
| #define USB_NAKLIMIT0 0xffc03858 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */ |
| #define USB_TXINTERVAL 0xffc03858 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */ |
| #define USB_RXTYPE 0xffc0385c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint */ |
| #define USB_RXINTERVAL 0xffc03860 /* Sets the polling interval for Interrupt and Isochronous transfers or the NAK response timeout on Bulk transfers */ |
| #define USB_TXCOUNT 0xffc03868 /* Number of bytes to be written to the selected endpoint Tx FIFO */ |
| |
| /* USB Endpoint FIFO Registers */ |
| |
| #define USB_EP0_FIFO 0xffc03880 /* Endpoint 0 FIFO */ |
| #define USB_EP1_FIFO 0xffc03888 /* Endpoint 1 FIFO */ |
| #define USB_EP2_FIFO 0xffc03890 /* Endpoint 2 FIFO */ |
| #define USB_EP3_FIFO 0xffc03898 /* Endpoint 3 FIFO */ |
| #define USB_EP4_FIFO 0xffc038a0 /* Endpoint 4 FIFO */ |
| #define USB_EP5_FIFO 0xffc038a8 /* Endpoint 5 FIFO */ |
| #define USB_EP6_FIFO 0xffc038b0 /* Endpoint 6 FIFO */ |
| #define USB_EP7_FIFO 0xffc038b8 /* Endpoint 7 FIFO */ |
| |
| /* USB OTG Control Registers */ |
| |
| #define USB_OTG_DEV_CTL 0xffc03900 /* OTG Device Control Register */ |
| #define USB_OTG_VBUS_IRQ 0xffc03904 /* OTG VBUS Control Interrupts */ |
| #define USB_OTG_VBUS_MASK 0xffc03908 /* VBUS Control Interrupt Enable */ |
| |
| /* USB Phy Control Registers */ |
| |
| #define USB_LINKINFO 0xffc03948 /* Enables programming of some PHY-side delays */ |
| #define USB_VPLEN 0xffc0394c /* Determines duration of VBUS pulse for VBUS charging */ |
| #define USB_HS_EOF1 0xffc03950 /* Time buffer for High-Speed transactions */ |
| #define USB_FS_EOF1 0xffc03954 /* Time buffer for Full-Speed transactions */ |
| #define USB_LS_EOF1 0xffc03958 /* Time buffer for Low-Speed transactions */ |
| |
| /* (APHY_CNTRL is for ADI usage only) */ |
| |
| #define USB_APHY_CNTRL 0xffc039e0 /* Register that increases visibility of Analog PHY */ |
| |
| /* (APHY_CALIB is for ADI usage only) */ |
| |
| #define USB_APHY_CALIB 0xffc039e4 /* Register used to set some calibration values */ |
| |
| #define USB_APHY_CNTRL2 0xffc039e8 /* Register used to prevent re-enumeration once Moab goes into hibernate mode */ |
| |
| /* (PHY_TEST is for ADI usage only) */ |
| |
| #define USB_PHY_TEST 0xffc039ec /* Used for reducing simulation time and simplifies FIFO testability */ |
| |
| #define USB_PLLOSC_CTRL 0xffc039f0 /* Used to program different parameters for USB PLL and Oscillator */ |
| #define USB_SRP_CLKDIV 0xffc039f4 /* Used to program clock divide value for the clock fed to the SRP detection logic */ |
| |
| /* USB Endpoint 0 Control Registers */ |
| |
| #define USB_EP_NI0_TXMAXP 0xffc03a00 /* Maximum packet size for Host Tx endpoint0 */ |
| #define USB_EP_NI0_TXCSR 0xffc03a04 /* Control Status register for endpoint 0 */ |
| #define USB_EP_NI0_RXMAXP 0xffc03a08 /* Maximum packet size for Host Rx endpoint0 */ |
| #define USB_EP_NI0_RXCSR 0xffc03a0c /* Control Status register for Host Rx endpoint0 */ |
| #define USB_EP_NI0_RXCOUNT 0xffc03a10 /* Number of bytes received in endpoint 0 FIFO */ |
| #define USB_EP_NI0_TXTYPE 0xffc03a14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint0 */ |
| #define USB_EP_NI0_TXINTERVAL 0xffc03a18 /* Sets the NAK response timeout on Endpoint 0 */ |
| #define USB_EP_NI0_RXTYPE 0xffc03a1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */ |
| #define USB_EP_NI0_RXINTERVAL 0xffc03a20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */ |
| #define USB_EP_NI0_TXCOUNT 0xffc03a28 /* Number of bytes to be written to the endpoint0 Tx FIFO */ |
| |
| /* USB Endpoint 1 Control Registers */ |
| |
| #define USB_EP_NI1_TXMAXP 0xffc03a40 /* Maximum packet size for Host Tx endpoint1 */ |
| #define USB_EP_NI1_TXCSR 0xffc03a44 /* Control Status register for endpoint1 */ |
| #define USB_EP_NI1_RXMAXP 0xffc03a48 /* Maximum packet size for Host Rx endpoint1 */ |
| #define USB_EP_NI1_RXCSR 0xffc03a4c /* Control Status register for Host Rx endpoint1 */ |
| #define USB_EP_NI1_RXCOUNT 0xffc03a50 /* Number of bytes received in endpoint1 FIFO */ |
| #define USB_EP_NI1_TXTYPE 0xffc03a54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint1 */ |
| #define USB_EP_NI1_TXINTERVAL 0xffc03a58 /* Sets the NAK response timeout on Endpoint1 */ |
| #define USB_EP_NI1_RXTYPE 0xffc03a5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */ |
| #define USB_EP_NI1_RXINTERVAL 0xffc03a60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */ |
| #define USB_EP_NI1_TXCOUNT 0xffc03a68 /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */ |
| |
| /* USB Endpoint 2 Control Registers */ |
| |
| #define USB_EP_NI2_TXMAXP 0xffc03a80 /* Maximum packet size for Host Tx endpoint2 */ |
| #define USB_EP_NI2_TXCSR 0xffc03a84 /* Control Status register for endpoint2 */ |
| #define USB_EP_NI2_RXMAXP 0xffc03a88 /* Maximum packet size for Host Rx endpoint2 */ |
| #define USB_EP_NI2_RXCSR 0xffc03a8c /* Control Status register for Host Rx endpoint2 */ |
| #define USB_EP_NI2_RXCOUNT 0xffc03a90 /* Number of bytes received in endpoint2 FIFO */ |
| #define USB_EP_NI2_TXTYPE 0xffc03a94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint2 */ |
| #define USB_EP_NI2_TXINTERVAL 0xffc03a98 /* Sets the NAK response timeout on Endpoint2 */ |
| #define USB_EP_NI2_RXTYPE 0xffc03a9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */ |
| #define USB_EP_NI2_RXINTERVAL 0xffc03aa0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */ |
| #define USB_EP_NI2_TXCOUNT 0xffc03aa8 /* Number of bytes to be written to the endpoint2 Tx FIFO */ |
| |
| /* USB Endpoint 3 Control Registers */ |
| |
| #define USB_EP_NI3_TXMAXP 0xffc03ac0 /* Maximum packet size for Host Tx endpoint3 */ |
| #define USB_EP_NI3_TXCSR 0xffc03ac4 /* Control Status register for endpoint3 */ |
| #define USB_EP_NI3_RXMAXP 0xffc03ac8 /* Maximum packet size for Host Rx endpoint3 */ |
| #define USB_EP_NI3_RXCSR 0xffc03acc /* Control Status register for Host Rx endpoint3 */ |
| #define USB_EP_NI3_RXCOUNT 0xffc03ad0 /* Number of bytes received in endpoint3 FIFO */ |
| #define USB_EP_NI3_TXTYPE 0xffc03ad4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint3 */ |
| #define USB_EP_NI3_TXINTERVAL 0xffc03ad8 /* Sets the NAK response timeout on Endpoint3 */ |
| #define USB_EP_NI3_RXTYPE 0xffc03adc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */ |
| #define USB_EP_NI3_RXINTERVAL 0xffc03ae0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */ |
| #define USB_EP_NI3_TXCOUNT 0xffc03ae8 /* Number of bytes to be written to the H124endpoint3 Tx FIFO */ |
| |
| /* USB Endpoint 4 Control Registers */ |
| |
| #define USB_EP_NI4_TXMAXP 0xffc03b00 /* Maximum packet size for Host Tx endpoint4 */ |
| #define USB_EP_NI4_TXCSR 0xffc03b04 /* Control Status register for endpoint4 */ |
| #define USB_EP_NI4_RXMAXP 0xffc03b08 /* Maximum packet size for Host Rx endpoint4 */ |
| #define USB_EP_NI4_RXCSR 0xffc03b0c /* Control Status register for Host Rx endpoint4 */ |
| #define USB_EP_NI4_RXCOUNT 0xffc03b10 /* Number of bytes received in endpoint4 FIFO */ |
| #define USB_EP_NI4_TXTYPE 0xffc03b14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint4 */ |
| #define USB_EP_NI4_TXINTERVAL 0xffc03b18 /* Sets the NAK response timeout on Endpoint4 */ |
| #define USB_EP_NI4_RXTYPE 0xffc03b1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */ |
| #define USB_EP_NI4_RXINTERVAL 0xffc03b20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */ |
| #define USB_EP_NI4_TXCOUNT 0xffc03b28 /* Number of bytes to be written to the endpoint4 Tx FIFO */ |
| |
| /* USB Endpoint 5 Control Registers */ |
| |
| #define USB_EP_NI5_TXMAXP 0xffc03b40 /* Maximum packet size for Host Tx endpoint5 */ |
| #define USB_EP_NI5_TXCSR 0xffc03b44 /* Control Status register for endpoint5 */ |
| #define USB_EP_NI5_RXMAXP 0xffc03b48 /* Maximum packet size for Host Rx endpoint5 */ |
| #define USB_EP_NI5_RXCSR 0xffc03b4c /* Control Status register for Host Rx endpoint5 */ |
| #define USB_EP_NI5_RXCOUNT 0xffc03b50 /* Number of bytes received in endpoint5 FIFO */ |
| #define USB_EP_NI5_TXTYPE 0xffc03b54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint5 */ |
| #define USB_EP_NI5_TXINTERVAL 0xffc03b58 /* Sets the NAK response timeout on Endpoint5 */ |
| #define USB_EP_NI5_RXTYPE 0xffc03b5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */ |
| #define USB_EP_NI5_RXINTERVAL 0xffc03b60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */ |
| #define USB_EP_NI5_TXCOUNT 0xffc03b68 /* Number of bytes to be written to the endpoint5 Tx FIFO */ |
| |
| /* USB Endpoint 6 Control Registers */ |
| |
| #define USB_EP_NI6_TXMAXP 0xffc03b80 /* Maximum packet size for Host Tx endpoint6 */ |
| #define USB_EP_NI6_TXCSR 0xffc03b84 /* Control Status register for endpoint6 */ |
| #define USB_EP_NI6_RXMAXP 0xffc03b88 /* Maximum packet size for Host Rx endpoint6 */ |
| #define USB_EP_NI6_RXCSR 0xffc03b8c /* Control Status register for Host Rx endpoint6 */ |
| #define USB_EP_NI6_RXCOUNT 0xffc03b90 /* Number of bytes received in endpoint6 FIFO */ |
| #define USB_EP_NI6_TXTYPE 0xffc03b94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint6 */ |
| #define USB_EP_NI6_TXINTERVAL 0xffc03b98 /* Sets the NAK response timeout on Endpoint6 */ |
| #define USB_EP_NI6_RXTYPE 0xffc03b9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */ |
| #define USB_EP_NI6_RXINTERVAL 0xffc03ba0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */ |
| #define USB_EP_NI6_TXCOUNT 0xffc03ba8 /* Number of bytes to be written to the endpoint6 Tx FIFO */ |
| |
| /* USB Endpoint 7 Control Registers */ |
| |
| #define USB_EP_NI7_TXMAXP 0xffc03bc0 /* Maximum packet size for Host Tx endpoint7 */ |
| #define USB_EP_NI7_TXCSR 0xffc03bc4 /* Control Status register for endpoint7 */ |
| #define USB_EP_NI7_RXMAXP 0xffc03bc8 /* Maximum packet size for Host Rx endpoint7 */ |
| #define USB_EP_NI7_RXCSR 0xffc03bcc /* Control Status register for Host Rx endpoint7 */ |
| #define USB_EP_NI7_RXCOUNT 0xffc03bd0 /* Number of bytes received in endpoint7 FIFO */ |
| #define USB_EP_NI7_TXTYPE 0xffc03bd4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */ |
| #define USB_EP_NI7_TXINTERVAL 0xffc03bd8 /* Sets the NAK response timeout on Endpoint7 */ |
| #define USB_EP_NI7_RXTYPE 0xffc03bdc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */ |
| #define USB_EP_NI7_RXINTERVAL 0xffc03bf0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */ |
| #define USB_EP_NI7_TXCOUNT 0xffc03bf8 /* Number of bytes to be written to the endpoint7 Tx FIFO */ |
| |
| #define USB_DMA_INTERRUPT 0xffc03c00 /* Indicates pending interrupts for the DMA channels */ |
| |
| /* USB Channel 0 Config Registers */ |
| |
| #define USB_DMA0CONTROL 0xffc03c04 /* DMA master channel 0 configuration */ |
| #define USB_DMA0ADDRLOW 0xffc03c08 /* Lower 16-bits of memory source/destination address for DMA master channel 0 */ |
| #define USB_DMA0ADDRHIGH 0xffc03c0c /* Upper 16-bits of memory source/destination address for DMA master channel 0 */ |
| #define USB_DMA0COUNTLOW 0xffc03c10 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 0 */ |
| #define USB_DMA0COUNTHIGH 0xffc03c14 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 0 */ |
| |
| /* USB Channel 1 Config Registers */ |
| |
| #define USB_DMA1CONTROL 0xffc03c24 /* DMA master channel 1 configuration */ |
| #define USB_DMA1ADDRLOW 0xffc03c28 /* Lower 16-bits of memory source/destination address for DMA master channel 1 */ |
| #define USB_DMA1ADDRHIGH 0xffc03c2c /* Upper 16-bits of memory source/destination address for DMA master channel 1 */ |
| #define USB_DMA1COUNTLOW 0xffc03c30 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 1 */ |
| #define USB_DMA1COUNTHIGH 0xffc03c34 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 1 */ |
| |
| /* USB Channel 2 Config Registers */ |
| |
| #define USB_DMA2CONTROL 0xffc03c44 /* DMA master channel 2 configuration */ |
| #define USB_DMA2ADDRLOW 0xffc03c48 /* Lower 16-bits of memory source/destination address for DMA master channel 2 */ |
| #define USB_DMA2ADDRHIGH 0xffc03c4c /* Upper 16-bits of memory source/destination address for DMA master channel 2 */ |
| #define USB_DMA2COUNTLOW 0xffc03c50 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 2 */ |
| #define USB_DMA2COUNTHIGH 0xffc03c54 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 2 */ |
| |
| /* USB Channel 3 Config Registers */ |
| |
| #define USB_DMA3CONTROL 0xffc03c64 /* DMA master channel 3 configuration */ |
| #define USB_DMA3ADDRLOW 0xffc03c68 /* Lower 16-bits of memory source/destination address for DMA master channel 3 */ |
| #define USB_DMA3ADDRHIGH 0xffc03c6c /* Upper 16-bits of memory source/destination address for DMA master channel 3 */ |
| #define USB_DMA3COUNTLOW 0xffc03c70 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 3 */ |
| #define USB_DMA3COUNTHIGH 0xffc03c74 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 3 */ |
| |
| /* USB Channel 4 Config Registers */ |
| |
| #define USB_DMA4CONTROL 0xffc03c84 /* DMA master channel 4 configuration */ |
| #define USB_DMA4ADDRLOW 0xffc03c88 /* Lower 16-bits of memory source/destination address for DMA master channel 4 */ |
| #define USB_DMA4ADDRHIGH 0xffc03c8c /* Upper 16-bits of memory source/destination address for DMA master channel 4 */ |
| #define USB_DMA4COUNTLOW 0xffc03c90 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 4 */ |
| #define USB_DMA4COUNTHIGH 0xffc03c94 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 4 */ |
| |
| /* USB Channel 5 Config Registers */ |
| |
| #define USB_DMA5CONTROL 0xffc03ca4 /* DMA master channel 5 configuration */ |
| #define USB_DMA5ADDRLOW 0xffc03ca8 /* Lower 16-bits of memory source/destination address for DMA master channel 5 */ |
| #define USB_DMA5ADDRHIGH 0xffc03cac /* Upper 16-bits of memory source/destination address for DMA master channel 5 */ |
| #define USB_DMA5COUNTLOW 0xffc03cb0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 5 */ |
| #define USB_DMA5COUNTHIGH 0xffc03cb4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 5 */ |
| |
| /* USB Channel 6 Config Registers */ |
| |
| #define USB_DMA6CONTROL 0xffc03cc4 /* DMA master channel 6 configuration */ |
| #define USB_DMA6ADDRLOW 0xffc03cc8 /* Lower 16-bits of memory source/destination address for DMA master channel 6 */ |
| #define USB_DMA6ADDRHIGH 0xffc03ccc /* Upper 16-bits of memory source/destination address for DMA master channel 6 */ |
| #define USB_DMA6COUNTLOW 0xffc03cd0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 6 */ |
| #define USB_DMA6COUNTHIGH 0xffc03cd4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 6 */ |
| |
| /* USB Channel 7 Config Registers */ |
| |
| #define USB_DMA7CONTROL 0xffc03ce4 /* DMA master channel 7 configuration */ |
| #define USB_DMA7ADDRLOW 0xffc03ce8 /* Lower 16-bits of memory source/destination address for DMA master channel 7 */ |
| #define USB_DMA7ADDRHIGH 0xffc03cec /* Upper 16-bits of memory source/destination address for DMA master channel 7 */ |
| #define USB_DMA7COUNTLOW 0xffc03cf0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 7 */ |
| #define USB_DMA7COUNTHIGH 0xffc03cf4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 7 */ |
| |
| /* Bit masks for USB_FADDR */ |
| |
| #define FUNCTION_ADDRESS 0x7f /* Function address */ |
| |
| /* Bit masks for USB_POWER */ |
| |
| #define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */ |
| #define nENABLE_SUSPENDM 0x0 |
| #define SUSPEND_MODE 0x2 /* Suspend Mode indicator */ |
| #define nSUSPEND_MODE 0x0 |
| #define RESUME_MODE 0x4 /* DMA Mode */ |
| #define nRESUME_MODE 0x0 |
| #define RESET 0x8 /* Reset indicator */ |
| #define nRESET 0x0 |
| #define HS_MODE 0x10 /* High Speed mode indicator */ |
| #define nHS_MODE 0x0 |
| #define HS_ENABLE 0x20 /* high Speed Enable */ |
| #define nHS_ENABLE 0x0 |
| #define SOFT_CONN 0x40 /* Soft connect */ |
| #define nSOFT_CONN 0x0 |
| #define ISO_UPDATE 0x80 /* Isochronous update */ |
| #define nISO_UPDATE 0x0 |
| |
| /* Bit masks for USB_INTRTX */ |
| |
| #define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */ |
| #define nEP0_TX 0x0 |
| #define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */ |
| #define nEP1_TX 0x0 |
| #define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */ |
| #define nEP2_TX 0x0 |
| #define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */ |
| #define nEP3_TX 0x0 |
| #define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */ |
| #define nEP4_TX 0x0 |
| #define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */ |
| #define nEP5_TX 0x0 |
| #define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */ |
| #define nEP6_TX 0x0 |
| #define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */ |
| #define nEP7_TX 0x0 |
| |
| /* Bit masks for USB_INTRRX */ |
| |
| #define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */ |
| #define nEP1_RX 0x0 |
| #define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */ |
| #define nEP2_RX 0x0 |
| #define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */ |
| #define nEP3_RX 0x0 |
| #define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */ |
| #define nEP4_RX 0x0 |
| #define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */ |
| #define nEP5_RX 0x0 |
| #define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */ |
| #define nEP6_RX 0x0 |
| #define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */ |
| #define nEP7_RX 0x0 |
| |
| /* Bit masks for USB_INTRTXE */ |
| |
| #define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */ |
| #define nEP0_TX_E 0x0 |
| #define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt Enable */ |
| #define nEP1_TX_E 0x0 |
| #define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt Enable */ |
| #define nEP2_TX_E 0x0 |
| #define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt Enable */ |
| #define nEP3_TX_E 0x0 |
| #define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt Enable */ |
| #define nEP4_TX_E 0x0 |
| #define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt Enable */ |
| #define nEP5_TX_E 0x0 |
| #define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt Enable */ |
| #define nEP6_TX_E 0x0 |
| #define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt Enable */ |
| #define nEP7_TX_E 0x0 |
| |
| /* Bit masks for USB_INTRRXE */ |
| |
| #define EP1_RX_E 0x2 /* Rx Endpoint 1 interrupt Enable */ |
| #define nEP1_RX_E 0x0 |
| #define EP2_RX_E 0x4 /* Rx Endpoint 2 interrupt Enable */ |
| #define nEP2_RX_E 0x0 |
| #define EP3_RX_E 0x8 /* Rx Endpoint 3 interrupt Enable */ |
| #define nEP3_RX_E 0x0 |
| #define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt Enable */ |
| #define nEP4_RX_E 0x0 |
| #define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt Enable */ |
| #define nEP5_RX_E 0x0 |
| #define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt Enable */ |
| #define nEP6_RX_E 0x0 |
| #define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt Enable */ |
| #define nEP7_RX_E 0x0 |
| |
| /* Bit masks for USB_INTRUSB */ |
| |
| #define SUSPEND_B 0x1 /* Suspend indicator */ |
| #define nSUSPEND_B 0x0 |
| #define RESUME_B 0x2 /* Resume indicator */ |
| #define nRESUME_B 0x0 |
| #define RESET_OR_BABLE_B 0x4 /* Reset/babble indicator */ |
| #define nRESET_OR_BABLE_B 0x0 |
| #define SOF_B 0x8 /* Start of frame */ |
| #define nSOF_B 0x0 |
| #define CONN_B 0x10 /* Connection indicator */ |
| #define nCONN_B 0x0 |
| #define DISCON_B 0x20 /* Disconnect indicator */ |
| #define nDISCON_B 0x0 |
| #define SESSION_REQ_B 0x40 /* Session Request */ |
| #define nSESSION_REQ_B 0x0 |
| #define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */ |
| #define nVBUS_ERROR_B 0x0 |
| |
| /* Bit masks for USB_INTRUSBE */ |
| |
| #define SUSPEND_BE 0x1 /* Suspend indicator int enable */ |
| #define nSUSPEND_BE 0x0 |
| #define RESUME_BE 0x2 /* Resume indicator int enable */ |
| #define nRESUME_BE 0x0 |
| #define RESET_OR_BABLE_BE 0x4 /* Reset/babble indicator int enable */ |
| #define nRESET_OR_BABLE_BE 0x0 |
| #define SOF_BE 0x8 /* Start of frame int enable */ |
| #define nSOF_BE 0x0 |
| #define CONN_BE 0x10 /* Connection indicator int enable */ |
| #define nCONN_BE 0x0 |
| #define DISCON_BE 0x20 /* Disconnect indicator int enable */ |
| #define nDISCON_BE 0x0 |
| #define SESSION_REQ_BE 0x40 /* Session Request int enable */ |
| #define nSESSION_REQ_BE 0x0 |
| #define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */ |
| #define nVBUS_ERROR_BE 0x0 |
| |
| /* Bit masks for USB_FRAME */ |
| |
| #define FRAME_NUMBER 0x7ff /* Frame number */ |
| |
| /* Bit masks for USB_INDEX */ |
| |
| #define SELECTED_ENDPOINT 0xf /* selected endpoint */ |
| |
| /* Bit masks for USB_GLOBAL_CTL */ |
| |
| #define GLOBAL_ENA 0x1 /* enables USB module */ |
| #define nGLOBAL_ENA 0x0 |
| #define EP1_TX_ENA 0x2 /* Transmit endpoint 1 enable */ |
| #define nEP1_TX_ENA 0x0 |
| #define EP2_TX_ENA 0x4 /* Transmit endpoint 2 enable */ |
| #define nEP2_TX_ENA 0x0 |
| #define EP3_TX_ENA 0x8 /* Transmit endpoint 3 enable */ |
| #define nEP3_TX_ENA 0x0 |
| #define EP4_TX_ENA 0x10 /* Transmit endpoint 4 enable */ |
| #define nEP4_TX_ENA 0x0 |
| #define EP5_TX_ENA 0x20 /* Transmit endpoint 5 enable */ |
| #define nEP5_TX_ENA 0x0 |
| #define EP6_TX_ENA 0x40 /* Transmit endpoint 6 enable */ |
| #define nEP6_TX_ENA 0x0 |
| #define EP7_TX_ENA 0x80 /* Transmit endpoint 7 enable */ |
| #define nEP7_TX_ENA 0x0 |
| #define EP1_RX_ENA 0x100 /* Receive endpoint 1 enable */ |
| #define nEP1_RX_ENA 0x0 |
| #define EP2_RX_ENA 0x200 /* Receive endpoint 2 enable */ |
| #define nEP2_RX_ENA 0x0 |
| #define EP3_RX_ENA 0x400 /* Receive endpoint 3 enable */ |
| #define nEP3_RX_ENA 0x0 |
| #define EP4_RX_ENA 0x800 /* Receive endpoint 4 enable */ |
| #define nEP4_RX_ENA 0x0 |
| #define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */ |
| #define nEP5_RX_ENA 0x0 |
| #define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */ |
| #define nEP6_RX_ENA 0x0 |
| #define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */ |
| #define nEP7_RX_ENA 0x0 |
| |
| /* Bit masks for USB_OTG_DEV_CTL */ |
| |
| #define SESSION 0x1 /* session indicator */ |
| #define nSESSION 0x0 |
| #define HOST_REQ 0x2 /* Host negotiation request */ |
| #define nHOST_REQ 0x0 |
| #define HOST_MODE 0x4 /* indicates USBDRC is a host */ |
| #define nHOST_MODE 0x0 |
| #define VBUS0 0x8 /* Vbus level indicator[0] */ |
| #define nVBUS0 0x0 |
| #define VBUS1 0x10 /* Vbus level indicator[1] */ |
| #define nVBUS1 0x0 |
| #define LSDEV 0x20 /* Low-speed indicator */ |
| #define nLSDEV 0x0 |
| #define FSDEV 0x40 /* Full or High-speed indicator */ |
| #define nFSDEV 0x0 |
| #define B_DEVICE 0x80 /* A' or 'B' device indicator */ |
| #define nB_DEVICE 0x0 |
| |
| /* Bit masks for USB_OTG_VBUS_IRQ */ |
| |
| #define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */ |
| #define nDRIVE_VBUS_ON 0x0 |
| #define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */ |
| #define nDRIVE_VBUS_OFF 0x0 |
| #define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */ |
| #define nCHRG_VBUS_START 0x0 |
| #define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */ |
| #define nCHRG_VBUS_END 0x0 |
| #define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */ |
| #define nDISCHRG_VBUS_START 0x0 |
| #define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */ |
| #define nDISCHRG_VBUS_END 0x0 |
| |
| /* Bit masks for USB_OTG_VBUS_MASK */ |
| |
| #define DRIVE_VBUS_ON_ENA 0x1 /* enable DRIVE_VBUS_ON interrupt */ |
| #define nDRIVE_VBUS_ON_ENA 0x0 |
| #define DRIVE_VBUS_OFF_ENA 0x2 /* enable DRIVE_VBUS_OFF interrupt */ |
| #define nDRIVE_VBUS_OFF_ENA 0x0 |
| #define CHRG_VBUS_START_ENA 0x4 /* enable CHRG_VBUS_START interrupt */ |
| #define nCHRG_VBUS_START_ENA 0x0 |
| #define CHRG_VBUS_END_ENA 0x8 /* enable CHRG_VBUS_END interrupt */ |
| #define nCHRG_VBUS_END_ENA 0x0 |
| #define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */ |
| #define nDISCHRG_VBUS_START_ENA 0x0 |
| #define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */ |
| #define nDISCHRG_VBUS_END_ENA 0x0 |
| |
| /* Bit masks for USB_CSR0 */ |
| |
| #define RXPKTRDY 0x1 /* data packet receive indicator */ |
| #define nRXPKTRDY 0x0 |
| #define TXPKTRDY 0x2 /* data packet in FIFO indicator */ |
| #define nTXPKTRDY 0x0 |
| #define STALL_SENT 0x4 /* STALL handshake sent */ |
| #define nSTALL_SENT 0x0 |
| #define DATAEND 0x8 /* Data end indicator */ |
| #define nDATAEND 0x0 |
| #define SETUPEND 0x10 /* Setup end */ |
| #define nSETUPEND 0x0 |
| #define SENDSTALL 0x20 /* Send STALL handshake */ |
| #define nSENDSTALL 0x0 |
| #define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */ |
| #define nSERVICED_RXPKTRDY 0x0 |
| #define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */ |
| #define nSERVICED_SETUPEND 0x0 |
| #define FLUSHFIFO 0x100 /* flush endpoint FIFO */ |
| #define nFLUSHFIFO 0x0 |
| #define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */ |
| #define nSTALL_RECEIVED_H 0x0 |
| #define SETUPPKT_H 0x8 /* send Setup token host mode */ |
| #define nSETUPPKT_H 0x0 |
| #define ERROR_H 0x10 /* timeout error indicator host mode */ |
| #define nERROR_H 0x0 |
| #define REQPKT_H 0x20 /* Request an IN transaction host mode */ |
| #define nREQPKT_H 0x0 |
| #define STATUSPKT_H 0x40 /* Status stage transaction host mode */ |
| #define nSTATUSPKT_H 0x0 |
| #define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */ |
| #define nNAK_TIMEOUT_H 0x0 |
| |
| /* Bit masks for USB_COUNT0 */ |
| |
| #define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */ |
| |
| /* Bit masks for USB_NAKLIMIT0 */ |
| |
| #define EP0_NAK_LIMIT 0x1f /* number of frames/micro frames after which EP0 timeouts */ |
| |
| /* Bit masks for USB_TX_MAX_PACKET */ |
| |
| #define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */ |
| |
| /* Bit masks for USB_RX_MAX_PACKET */ |
| |
| #define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */ |
| |
| /* Bit masks for USB_TXCSR */ |
| |
| #define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */ |
| #define nTXPKTRDY_T 0x0 |
| #define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */ |
| #define nFIFO_NOT_EMPTY_T 0x0 |
| #define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */ |
| #define nUNDERRUN_T 0x0 |
| #define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */ |
| #define nFLUSHFIFO_T 0x0 |
| #define STALL_SEND_T 0x10 /* issue a Stall handshake */ |
| #define nSTALL_SEND_T 0x0 |
| #define STALL_SENT_T 0x20 /* Stall handshake transmitted */ |
| #define nSTALL_SENT_T 0x0 |
| #define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */ |
| #define nCLEAR_DATATOGGLE_T 0x0 |
| #define INCOMPTX_T 0x80 /* indicates that a large packet is split */ |
| #define nINCOMPTX_T 0x0 |
| #define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */ |
| #define nDMAREQMODE_T 0x0 |
| #define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */ |
| #define nFORCE_DATATOGGLE_T 0x0 |
| #define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */ |
| #define nDMAREQ_ENA_T 0x0 |
| #define ISO_T 0x4000 /* enable Isochronous transfers */ |
| #define nISO_T 0x0 |
| #define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */ |
| #define nAUTOSET_T 0x0 |
| #define ERROR_TH 0x4 /* error condition host mode */ |
| #define nERROR_TH 0x0 |
| #define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */ |
| #define nSTALL_RECEIVED_TH 0x0 |
| #define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */ |
| #define nNAK_TIMEOUT_TH 0x0 |
| |
| /* Bit masks for USB_TXCOUNT */ |
| |
| #define TX_COUNT 0x1fff /* Number of bytes to be written to the selected endpoint Tx FIFO */ |
| |
| /* Bit masks for USB_RXCSR */ |
| |
| #define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */ |
| #define nRXPKTRDY_R 0x0 |
| #define FIFO_FULL_R 0x2 /* FIFO not empty */ |
| #define nFIFO_FULL_R 0x0 |
| #define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */ |
| #define nOVERRUN_R 0x0 |
| #define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */ |
| #define nDATAERROR_R 0x0 |
| #define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */ |
| #define nFLUSHFIFO_R 0x0 |
| #define STALL_SEND_R 0x20 /* issue a Stall handshake */ |
| #define nSTALL_SEND_R 0x0 |
| #define STALL_SENT_R 0x40 /* Stall handshake transmitted */ |
| #define nSTALL_SENT_R 0x0 |
| #define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */ |
| #define nCLEAR_DATATOGGLE_R 0x0 |
| #define INCOMPRX_R 0x100 /* indicates that a large packet is split */ |
| #define nINCOMPRX_R 0x0 |
| #define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */ |
| #define nDMAREQMODE_R 0x0 |
| #define DISNYET_R 0x1000 /* disable Nyet handshakes */ |
| #define nDISNYET_R 0x0 |
| #define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */ |
| #define nDMAREQ_ENA_R 0x0 |
| #define ISO_R 0x4000 /* enable Isochronous transfers */ |
| #define nISO_R 0x0 |
| #define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */ |
| #define nAUTOCLEAR_R 0x0 |
| #define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */ |
| #define nERROR_RH 0x0 |
| #define REQPKT_RH 0x20 /* request an IN transaction host mode */ |
| #define nREQPKT_RH 0x0 |
| #define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */ |
| #define nSTALL_RECEIVED_RH 0x0 |
| #define INCOMPRX_RH 0x100 /* indicates that a large packet is split host mode */ |
| #define nINCOMPRX_RH 0x0 |
| #define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */ |
| #define nDMAREQMODE_RH 0x0 |
| #define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */ |
| #define nAUTOREQ_RH 0x0 |
| |
| /* Bit masks for USB_RXCOUNT */ |
| |
| #define RX_COUNT 0x1fff /* Number of received bytes in the packet in the Rx FIFO */ |
| |
| /* Bit masks for USB_TXTYPE */ |
| |
| #define TARGET_EP_NO_T 0xf /* EP number */ |
| #define PROTOCOL_T 0xc /* transfer type */ |
| |
| /* Bit masks for USB_TXINTERVAL */ |
| |
| #define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */ |
| |
| /* Bit masks for USB_RXTYPE */ |
| |
| #define TARGET_EP_NO_R 0xf /* EP number */ |
| #define PROTOCOL_R 0xc /* transfer type */ |
| |
| /* Bit masks for USB_RXINTERVAL */ |
| |
| #define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */ |
| |
| /* Bit masks for USB_DMA_INTERRUPT */ |
| |
| #define DMA0_INT 0x1 /* DMA0 pending interrupt */ |
| #define nDMA0_INT 0x0 |
| #define DMA1_INT 0x2 /* DMA1 pending interrupt */ |
| #define nDMA1_INT 0x0 |
| #define DMA2_INT 0x4 /* DMA2 pending interrupt */ |
| #define nDMA2_INT 0x0 |
| #define DMA3_INT 0x8 /* DMA3 pending interrupt */ |
| #define nDMA3_INT 0x0 |
| #define DMA4_INT 0x10 /* DMA4 pending interrupt */ |
| #define nDMA4_INT 0x0 |
| #define DMA5_INT 0x20 /* DMA5 pending interrupt */ |
| #define nDMA5_INT 0x0 |
| #define DMA6_INT 0x40 /* DMA6 pending interrupt */ |
| #define nDMA6_INT 0x0 |
| #define DMA7_INT 0x80 /* DMA7 pending interrupt */ |
| #define nDMA7_INT 0x0 |
| |
| /* Bit masks for USB_DMAxCONTROL */ |
| |
| #define DMA_ENA 0x1 /* DMA enable */ |
| #define nDMA_ENA 0x0 |
| #define DIRECTION 0x2 /* direction of DMA transfer */ |
| #define nDIRECTION 0x0 |
| #define MODE 0x4 /* DMA Bus error */ |
| #define nMODE 0x0 |
| #define INT_ENA 0x8 /* Interrupt enable */ |
| #define nINT_ENA 0x0 |
| #define EPNUM 0xf0 /* EP number */ |
| #define BUSERROR 0x100 /* DMA Bus error */ |
| #define nBUSERROR 0x0 |
| |
| /* Bit masks for USB_DMAxADDRHIGH */ |
| |
| #define DMA_ADDR_HIGH 0xffff /* Upper 16-bits of memory source/destination address for the DMA master channel */ |
| |
| /* Bit masks for USB_DMAxADDRLOW */ |
| |
| #define DMA_ADDR_LOW 0xffff /* Lower 16-bits of memory source/destination address for the DMA master channel */ |
| |
| /* Bit masks for USB_DMAxCOUNTHIGH */ |
| |
| #define DMA_COUNT_HIGH 0xffff /* Upper 16-bits of byte count of DMA transfer for DMA master channel */ |
| |
| /* Bit masks for USB_DMAxCOUNTLOW */ |
| |
| #define DMA_COUNT_LOW 0xffff /* Lower 16-bits of byte count of DMA transfer for DMA master channel */ |
| |
| #endif /* _DEF_BF525_H */ |