i2c: Bus drivers return -Errno not -1
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
diff --git a/drivers/i2c/algos/i2c-algo-bit.c b/drivers/i2c/algos/i2c-algo-bit.c
index 3581282..eb8f72c 100644
--- a/drivers/i2c/algos/i2c-algo-bit.c
+++ b/drivers/i2c/algos/i2c-algo-bit.c
@@ -320,7 +320,7 @@
unsigned char addr, int retries)
{
struct i2c_algo_bit_data *adap = i2c_adap->algo_data;
- int i, ret = -1;
+ int i, ret = 0;
for (i = 0; i <= retries; i++) {
ret = i2c_outb(i2c_adap, addr);
@@ -508,7 +508,7 @@
addr ^= 1;
ret = try_address(i2c_adap, addr, retries);
if ((ret != 1) && !nak_ok)
- return -EREMOTEIO;
+ return -ENXIO;
}
return 0;
diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c
index f14372a..c21e4d9 100644
--- a/drivers/i2c/busses/i2c-ali1535.c
+++ b/drivers/i2c/busses/i2c-ali1535.c
@@ -259,7 +259,7 @@
dev_err(&adap->dev,
"SMBus reset failed! (0x%02x) - controller or "
"device on bus is probably hung\n", temp);
- return -1;
+ return -EBUSY;
}
} else {
/* check and clear done bit */
@@ -281,12 +281,12 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "SMBus Timeout!\n");
}
if (temp & ALI1535_STS_FAIL) {
- result = -1;
+ result = -EIO;
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
}
@@ -295,7 +295,7 @@
* do a printk. This means that bus collisions go unreported.
*/
if (temp & ALI1535_STS_BUSERR) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&adap->dev,
"Error: no response or bus collision ADD=%02x\n",
inb_p(SMBHSTADD));
@@ -303,13 +303,13 @@
/* haven't ever seen this */
if (temp & ALI1535_STS_DEV) {
- result = -1;
+ result = -EIO;
dev_err(&adap->dev, "Error: device error\n");
}
/* check to see if the "command complete" indication is set */
if (!(temp & ALI1535_STS_DONE)) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "Error: command never completed\n");
}
@@ -332,7 +332,7 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 ali1535_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data *data)
@@ -359,7 +359,7 @@
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
- result = -1;
+ result = -EOPNOTSUPP;
goto EXIT;
case I2C_SMBUS_QUICK:
outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
@@ -420,11 +420,9 @@
break;
}
- if (ali1535_transaction(adap)) {
- /* Error in transaction */
- result = -1;
+ result = ali1535_transaction(adap);
+ if (result)
goto EXIT;
- }
if ((read_write == I2C_SMBUS_WRITE) || (size == ALI1535_QUICK)) {
result = 0;
diff --git a/drivers/i2c/busses/i2c-ali1563.c b/drivers/i2c/busses/i2c-ali1563.c
index 6b68074..30bd3ee 100644
--- a/drivers/i2c/busses/i2c-ali1563.c
+++ b/drivers/i2c/busses/i2c-ali1563.c
@@ -67,6 +67,7 @@
{
u32 data;
int timeout;
+ int status = -EIO;
dev_dbg(&a->dev, "Transaction (pre): STS=%02x, CNTL1=%02x, "
"CNTL2=%02x, CMD=%02x, ADD=%02x, DAT0=%02x, DAT1=%02x\n",
@@ -103,13 +104,15 @@
/* Issue 'kill' to host controller */
outb_p(HST_CNTL2_KILL,SMB_HST_CNTL2);
data = inb_p(SMB_HST_STS);
+ status = -ETIMEDOUT;
}
/* device error - no response, ignore the autodetection case */
- if ((data & HST_STS_DEVERR) && (size != HST_CNTL2_QUICK)) {
- dev_err(&a->dev, "Device error!\n");
+ if (data & HST_STS_DEVERR) {
+ if (size != HST_CNTL2_QUICK)
+ dev_err(&a->dev, "Device error!\n");
+ status = -ENXIO;
}
-
/* bus collision */
if (data & HST_STS_BUSERR) {
dev_err(&a->dev, "Bus collision!\n");
@@ -122,13 +125,14 @@
outb_p(0x0,SMB_HST_CNTL2);
}
- return -1;
+ return status;
}
static int ali1563_block_start(struct i2c_adapter * a)
{
u32 data;
int timeout;
+ int status = -EIO;
dev_dbg(&a->dev, "Block (pre): STS=%02x, CNTL1=%02x, "
"CNTL2=%02x, CMD=%02x, ADD=%02x, DAT0=%02x, DAT1=%02x\n",
@@ -164,13 +168,20 @@
if (timeout && !(data & HST_STS_BAD))
return 0;
+
+ if (timeout == 0)
+ status = -ETIMEDOUT;
+
+ if (data & HST_STS_DEVERR)
+ status = -ENXIO;
+
dev_err(&a->dev, "SMBus Error: %s%s%s%s%s\n",
- timeout ? "Timeout " : "",
+ timeout ? "" : "Timeout ",
data & HST_STS_FAIL ? "Transaction Failed " : "",
data & HST_STS_BUSERR ? "No response or Bus Collision " : "",
data & HST_STS_DEVERR ? "Device Error " : "",
!(data & HST_STS_DONE) ? "Transaction Never Finished " : "");
- return -1;
+ return status;
}
static int ali1563_block(struct i2c_adapter * a, union i2c_smbus_data * data, u8 rw)
diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c
index 93bf87d..3d75256 100644
--- a/drivers/i2c/busses/i2c-ali15x3.c
+++ b/drivers/i2c/busses/i2c-ali15x3.c
@@ -282,7 +282,7 @@
dev_err(&adap->dev, "SMBus reset failed! (0x%02x) - "
"controller or device on bus is probably hung\n",
temp);
- return -1;
+ return -EBUSY;
}
} else {
/* check and clear done bit */
@@ -304,12 +304,12 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "SMBus Timeout!\n");
}
if (temp & ALI15X3_STS_TERM) {
- result = -1;
+ result = -EIO;
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
}
@@ -320,7 +320,7 @@
This means that bus collisions go unreported.
*/
if (temp & ALI15X3_STS_COLL) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&adap->dev,
"Error: no response or bus collision ADD=%02x\n",
inb_p(SMBHSTADD));
@@ -328,7 +328,7 @@
/* haven't ever seen this */
if (temp & ALI15X3_STS_DEV) {
- result = -1;
+ result = -EIO;
dev_err(&adap->dev, "Error: device error\n");
}
dev_dbg(&adap->dev, "Transaction (post): STS=%02x, CNT=%02x, CMD=%02x, "
@@ -338,7 +338,7 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data * data)
@@ -364,7 +364,7 @@
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
- return -1;
+ return -EOPNOTSUPP;
case I2C_SMBUS_QUICK:
outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
SMBHSTADD);
@@ -421,8 +421,9 @@
outb_p(size, SMBHSTCNT); /* output command */
- if (ali15x3_transaction(adap)) /* Error in transaction */
- return -1;
+ temp = ali15x3_transaction(adap);
+ if (temp)
+ return temp;
if ((read_write == I2C_SMBUS_WRITE) || (size == ALI15X3_QUICK))
return 0;
diff --git a/drivers/i2c/busses/i2c-amd756-s4882.c b/drivers/i2c/busses/i2c-amd756-s4882.c
index c38a0a1..2f150e3 100644
--- a/drivers/i2c/busses/i2c-amd756-s4882.c
+++ b/drivers/i2c/busses/i2c-amd756-s4882.c
@@ -58,7 +58,7 @@
/* We exclude the multiplexed addresses */
if (addr == 0x4c || (addr & 0xfc) == 0x50 || (addr & 0xfc) == 0x30
|| addr == 0x18)
- return -1;
+ return -ENXIO;
mutex_lock(&amd756_lock);
@@ -86,7 +86,7 @@
/* We exclude the non-multiplexed addresses */
if (addr != 0x4c && (addr & 0xfc) != 0x50 && (addr & 0xfc) != 0x30)
- return -1;
+ return -ENXIO;
mutex_lock(&amd756_lock);
diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c
index 43508d6..3d5bcb6 100644
--- a/drivers/i2c/busses/i2c-amd756.c
+++ b/drivers/i2c/busses/i2c-amd756.c
@@ -151,17 +151,17 @@
}
if (temp & GS_PRERR_STS) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&adap->dev, "SMBus Protocol error (no response)!\n");
}
if (temp & GS_COL_STS) {
- result = -1;
+ result = -EIO;
dev_warn(&adap->dev, "SMBus collision!\n");
}
if (temp & GS_TO_STS) {
- result = -1;
+ result = -ETIMEDOUT;
dev_dbg(&adap->dev, "SMBus protocol timeout!\n");
}
@@ -189,22 +189,23 @@
outw_p(inw(SMB_GLOBAL_ENABLE) | GE_ABORT, SMB_GLOBAL_ENABLE);
msleep(100);
outw_p(GS_CLEAR_STS, SMB_GLOBAL_STATUS);
- return -1;
+ return -EIO;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 amd756_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data * data)
{
int i, len;
+ int status;
/** TODO: Should I supporte the 10-bit transfers? */
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_dbg(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
/* TODO: Well... It is supported, I'm just not sure what to do here... */
- return -1;
+ return -EOPNOTSUPP;
case I2C_SMBUS_QUICK:
outw_p(((addr & 0x7f) << 1) | (read_write & 0x01),
SMB_HOST_ADDRESS);
@@ -256,8 +257,9 @@
/* How about enabling interrupts... */
outw_p(size & GE_CYC_TYPE_MASK, SMB_GLOBAL_ENABLE);
- if (amd756_transaction(adap)) /* Error in transaction */
- return -1;
+ status = amd756_transaction(adap);
+ if (status)
+ return status;
if ((read_write == I2C_SMBUS_WRITE) || (size == AMD756_QUICK))
return 0;
diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c
index 5d1a27e..a4f6879 100644
--- a/drivers/i2c/busses/i2c-amd8111.c
+++ b/drivers/i2c/busses/i2c-amd8111.c
@@ -77,7 +77,7 @@
if (!timeout) {
dev_warn(&smbus->dev->dev,
"Timeout while waiting for IBF to clear\n");
- return -1;
+ return -ETIMEDOUT;
}
return 0;
@@ -93,7 +93,7 @@
if (!timeout) {
dev_warn(&smbus->dev->dev,
"Timeout while waiting for OBF to set\n");
- return -1;
+ return -ETIMEDOUT;
}
return 0;
@@ -102,16 +102,21 @@
static unsigned int amd_ec_read(struct amd_smbus *smbus, unsigned char address,
unsigned char *data)
{
- if (amd_ec_wait_write(smbus))
- return -1;
+ int status;
+
+ status = amd_ec_wait_write(smbus);
+ if (status)
+ return status;
outb(AMD_EC_CMD_RD, smbus->base + AMD_EC_CMD);
- if (amd_ec_wait_write(smbus))
- return -1;
+ status = amd_ec_wait_write(smbus);
+ if (status)
+ return status;
outb(address, smbus->base + AMD_EC_DATA);
- if (amd_ec_wait_read(smbus))
- return -1;
+ status = amd_ec_wait_read(smbus);
+ if (status)
+ return status;
*data = inb(smbus->base + AMD_EC_DATA);
return 0;
@@ -120,16 +125,21 @@
static unsigned int amd_ec_write(struct amd_smbus *smbus, unsigned char address,
unsigned char data)
{
- if (amd_ec_wait_write(smbus))
- return -1;
+ int status;
+
+ status = amd_ec_wait_write(smbus);
+ if (status)
+ return status;
outb(AMD_EC_CMD_WR, smbus->base + AMD_EC_CMD);
- if (amd_ec_wait_write(smbus))
- return -1;
+ status = amd_ec_wait_write(smbus);
+ if (status)
+ return status;
outb(address, smbus->base + AMD_EC_DATA);
- if (amd_ec_wait_write(smbus))
- return -1;
+ status = amd_ec_wait_write(smbus);
+ if (status)
+ return status;
outb(data, smbus->base + AMD_EC_DATA);
return 0;
@@ -267,12 +277,17 @@
default:
dev_warn(&adap->dev, "Unsupported transaction %d\n", size);
- return -1;
+ return -EOPNOTSUPP;
}
amd_ec_write(smbus, AMD_SMB_ADDR, addr << 1);
amd_ec_write(smbus, AMD_SMB_PRTCL, protocol);
+ /* FIXME this discards status from ec_read(); so temp[0] will
+ * hold stack garbage ... the rest of this routine will act
+ * nonsensically. Ignored ec_write() status might explain
+ * some such failures...
+ */
amd_ec_read(smbus, AMD_SMB_STS, temp + 0);
if (~temp[0] & AMD_SMB_STS_DONE) {
@@ -286,7 +301,7 @@
}
if ((~temp[0] & AMD_SMB_STS_DONE) || (temp[0] & AMD_SMB_STS_STATUS))
- return -1;
+ return -EIO;
if (read_write == I2C_SMBUS_WRITE)
return 0;
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index b0f771f..7d6d9df 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -151,7 +151,7 @@
outb_p(temp, SMBHSTSTS);
if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) {
dev_dbg(&I801_dev->dev, "Failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&I801_dev->dev, "Successful!\n");
}
@@ -170,7 +170,7 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_dbg(&I801_dev->dev, "SMBus Timeout!\n");
- result = -1;
+ result = -ETIMEDOUT;
/* try to stop the current command */
dev_dbg(&I801_dev->dev, "Terminating the current operation\n");
outb_p(inb_p(SMBHSTCNT) | SMBHSTCNT_KILL, SMBHSTCNT);
@@ -179,19 +179,19 @@
}
if (temp & SMBHSTSTS_FAILED) {
- result = -1;
+ result = -EIO;
dev_dbg(&I801_dev->dev, "Error: Failed bus transaction\n");
}
if (temp & SMBHSTSTS_BUS_ERR) {
- result = -1;
+ result = -EIO;
dev_err(&I801_dev->dev, "Bus collision! SMBus may be locked "
"until next hard reset. (sorry!)\n");
/* Clock stops and slave is stuck in mid-transmission */
}
if (temp & SMBHSTSTS_DEV_ERR) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&I801_dev->dev, "Error: no response!\n");
}
@@ -231,6 +231,7 @@
char read_write, int hwpec)
{
int i, len;
+ int status;
inb_p(SMBHSTCNT); /* reset the data buffer index */
@@ -242,14 +243,15 @@
outb_p(data->block[i+1], SMBBLKDAT);
}
- if (i801_transaction(I801_BLOCK_DATA | ENABLE_INT9 |
- I801_PEC_EN * hwpec))
- return -1;
+ status = i801_transaction(I801_BLOCK_DATA | ENABLE_INT9 |
+ I801_PEC_EN * hwpec);
+ if (status)
+ return status;
if (read_write == I2C_SMBUS_READ) {
len = inb_p(SMBHSTDAT0);
if (len < 1 || len > I2C_SMBUS_BLOCK_MAX)
- return -1;
+ return -EPROTO;
data->block[0] = len;
for (i = 0; i < len; i++)
@@ -314,11 +316,11 @@
if (((temp = inb_p(SMBHSTSTS)) & errmask) != 0x00) {
dev_err(&I801_dev->dev,
"Reset failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
}
if (i != 1)
/* if die in middle of block transaction, fail */
- return -1;
+ return -EIO;
}
if (i == 1)
@@ -342,19 +344,19 @@
msleep(1);
outb_p(inb_p(SMBHSTCNT) & (~SMBHSTCNT_KILL),
SMBHSTCNT);
- result = -1;
+ result = -ETIMEDOUT;
dev_dbg(&I801_dev->dev, "SMBus Timeout!\n");
}
if (temp & SMBHSTSTS_FAILED) {
- result = -1;
+ result = -EIO;
dev_dbg(&I801_dev->dev,
"Error: Failed bus transaction\n");
} else if (temp & SMBHSTSTS_BUS_ERR) {
- result = -1;
+ result = -EIO;
dev_err(&I801_dev->dev, "Bus collision!\n");
} else if (temp & SMBHSTSTS_DEV_ERR) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&I801_dev->dev, "Error: no response!\n");
}
@@ -362,7 +364,7 @@
&& command != I2C_SMBUS_I2C_BLOCK_DATA) {
len = inb_p(SMBHSTDAT0);
if (len < 1 || len > I2C_SMBUS_BLOCK_MAX)
- return -1;
+ return -EPROTO;
data->block[0] = len;
}
@@ -394,7 +396,7 @@
{
outb_p(inb_p(SMBAUXCTL) | SMBAUXCTL_E32B, SMBAUXCTL);
if ((inb_p(SMBAUXCTL) & SMBAUXCTL_E32B) == 0)
- return -1;
+ return -EIO;
return 0;
}
@@ -414,7 +416,7 @@
} else if (!(i801_features & FEATURE_I2C_BLOCK_READ)) {
dev_err(&I801_dev->dev,
"I2C block read is unsupported!\n");
- return -1;
+ return -EOPNOTSUPP;
}
}
@@ -449,7 +451,7 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 i801_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data * data)
@@ -514,7 +516,7 @@
case I2C_SMBUS_PROC_CALL:
default:
dev_err(&I801_dev->dev, "Unsupported transaction %d\n", size);
- return -1;
+ return -EOPNOTSUPP;
}
if (hwpec) /* enable/disable hardware PEC */
@@ -537,7 +539,7 @@
if(block)
return ret;
if(ret)
- return -1;
+ return ret;
if ((read_write == I2C_SMBUS_WRITE) || (xact == I801_QUICK))
return 0;
diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c
index f95efff..081fdf3 100644
--- a/drivers/i2c/busses/i2c-nforce2.c
+++ b/drivers/i2c/busses/i2c-nforce2.c
@@ -172,16 +172,16 @@
dev_dbg(&adap->dev, "SMBus Timeout!\n");
if (smbus->can_abort)
nforce2_abort(adap);
- return -1;
+ return -ETIMEDOUT;
}
if (!(temp & NVIDIA_SMB_STS_DONE) || (temp & NVIDIA_SMB_STS_STATUS)) {
dev_dbg(&adap->dev, "Transaction failed (0x%02x)!\n", temp);
- return -1;
+ return -EIO;
}
return 0;
}
-/* Return -1 on error */
+/* Return negative errno on error */
static s32 nforce2_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data * data)
@@ -189,7 +189,7 @@
struct nforce2_smbus *smbus = adap->algo_data;
unsigned char protocol, pec;
u8 len;
- int i;
+ int i, status;
protocol = (read_write == I2C_SMBUS_READ) ? NVIDIA_SMB_PRTCL_READ :
NVIDIA_SMB_PRTCL_WRITE;
@@ -233,7 +233,7 @@
"Transaction failed "
"(requested block size: %d)\n",
len);
- return -1;
+ return -EINVAL;
}
outb_p(len, NVIDIA_SMB_BCNT);
for (i = 0; i < I2C_SMBUS_BLOCK_MAX; i++)
@@ -245,14 +245,15 @@
default:
dev_err(&adap->dev, "Unsupported transaction %d\n", size);
- return -1;
+ return -EOPNOTSUPP;
}
outb_p((addr & 0x7f) << 1, NVIDIA_SMB_ADDR);
outb_p(protocol, NVIDIA_SMB_PRTCL);
- if (nforce2_check_status(adap))
- return -1;
+ status = nforce2_check_status(adap);
+ if (status)
+ return status;
if (read_write == I2C_SMBUS_WRITE)
return 0;
@@ -274,7 +275,7 @@
dev_err(&adap->dev, "Transaction failed "
"(received block size: 0x%02x)\n",
len);
- return -1;
+ return -EPROTO;
}
for (i = 0; i < len; i++)
data->block[i+1] = inb_p(NVIDIA_SMB_DATA + i);
@@ -335,7 +336,7 @@
!= PCIBIOS_SUCCESSFUL) {
dev_err(&dev->dev, "Error reading PCI config for %s\n",
name);
- return -1;
+ return -EIO;
}
smbus->base = iobase & PCI_BASE_ADDRESS_IO_MASK;
@@ -345,7 +346,7 @@
if (!request_region(smbus->base, smbus->size, nforce2_driver.name)) {
dev_err(&smbus->adapter.dev, "Error requesting region %02x .. %02X for %s\n",
smbus->base, smbus->base+smbus->size-1, name);
- return -1;
+ return -EBUSY;
}
smbus->adapter.owner = THIS_MODULE;
smbus->adapter.id = I2C_HW_SMBUS_NFORCE2;
@@ -360,7 +361,7 @@
if (error) {
dev_err(&smbus->adapter.dev, "Failed to register adapter.\n");
release_region(smbus->base, smbus->size);
- return -1;
+ return error;
}
dev_info(&smbus->adapter.dev, "nForce2 SMBus adapter at %#x\n", smbus->base);
return 0;
diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c
index ac91659..dc76c0e 100644
--- a/drivers/i2c/busses/i2c-piix4.c
+++ b/drivers/i2c/busses/i2c-piix4.c
@@ -253,7 +253,7 @@
outb_p(temp, SMBHSTSTS);
if ((temp = inb_p(SMBHSTSTS)) != 0x00) {
dev_err(&piix4_adapter.dev, "Failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&piix4_adapter.dev, "Successful!\n");
}
@@ -275,23 +275,23 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_err(&piix4_adapter.dev, "SMBus Timeout!\n");
- result = -1;
+ result = -ETIMEDOUT;
}
if (temp & 0x10) {
- result = -1;
+ result = -EIO;
dev_err(&piix4_adapter.dev, "Error: Failed bus transaction\n");
}
if (temp & 0x08) {
- result = -1;
+ result = -EIO;
dev_dbg(&piix4_adapter.dev, "Bus collision! SMBus may be "
"locked until next hard reset. (sorry!)\n");
/* Clock stops and slave is stuck in mid-transmission */
}
if (temp & 0x04) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&piix4_adapter.dev, "Error: no response!\n");
}
@@ -309,17 +309,18 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 piix4_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data * data)
{
int i, len;
+ int status;
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
- return -1;
+ return -EOPNOTSUPP;
case I2C_SMBUS_QUICK:
outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
SMBHSTADD);
@@ -371,8 +372,9 @@
outb_p((size & 0x1C) + (ENABLE_INT9 & 1), SMBHSTCNT);
- if (piix4_transaction()) /* Error in transaction */
- return -1;
+ status = piix4_transaction();
+ if (status)
+ return status;
if ((read_write == I2C_SMBUS_WRITE) || (size == PIIX4_QUICK))
return 0;
diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c
index 9ca8f91..328441b 100644
--- a/drivers/i2c/busses/i2c-sis5595.c
+++ b/drivers/i2c/busses/i2c-sis5595.c
@@ -236,7 +236,7 @@
sis5595_write(SMB_STS_HI, temp >> 8);
if ((temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8)) != 0x00) {
dev_dbg(&adap->dev, "Failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&adap->dev, "Successful!\n");
}
@@ -254,19 +254,19 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_dbg(&adap->dev, "SMBus Timeout!\n");
- result = -1;
+ result = -ETIMEDOUT;
}
if (temp & 0x10) {
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
- result = -1;
+ result = -ENXIO;
}
if (temp & 0x20) {
dev_err(&adap->dev, "Bus collision! SMBus may be locked until "
"next hard reset (or not...)\n");
/* Clock stops and slave is stuck in mid-transmission */
- result = -1;
+ result = -EIO;
}
temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8);
@@ -282,11 +282,13 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 sis5595_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data *data)
{
+ int status;
+
switch (size) {
case I2C_SMBUS_QUICK:
sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01));
@@ -318,13 +320,14 @@
break;
default:
dev_warn(&adap->dev, "Unsupported transaction %d\n", size);
- return -1;
+ return -EOPNOTSUPP;
}
sis5595_write(SMB_CTL_LO, ((size & 0x0E)));
- if (sis5595_transaction(adap))
- return -1;
+ status = sis5595_transaction(adap);
+ if (status)
+ return status;
if ((size != SIS5595_PROC_CALL) &&
((read_write == I2C_SMBUS_WRITE) || (size == SIS5595_QUICK)))
diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c
index 3765dd7..c4cc5ed 100644
--- a/drivers/i2c/busses/i2c-sis630.c
+++ b/drivers/i2c/busses/i2c-sis630.c
@@ -134,7 +134,7 @@
if ((temp = sis630_read(SMB_CNT) & 0x03) != 0x00) {
dev_dbg(&adap->dev, "Failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&adap->dev, "Successful!\n");
}
@@ -177,17 +177,17 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_dbg(&adap->dev, "SMBus Timeout!\n");
- result = -1;
+ result = -ETIMEDOUT;
}
if (temp & 0x02) {
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
- result = -1;
+ result = -ENXIO;
}
if (temp & 0x04) {
dev_err(&adap->dev, "Bus collision!\n");
- result = -1;
+ result = -EIO;
/*
TBD: Datasheet say:
the software should clear this bit and restart SMBUS operation.
@@ -250,8 +250,10 @@
if (i==8 || (len<8 && i==len)) {
dev_dbg(&adap->dev, "start trans len=%d i=%d\n",len ,i);
/* first transaction */
- if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock))
- return -1;
+ rc = sis630_transaction_start(adap,
+ SIS630_BLOCK_DATA, &oldclock);
+ if (rc)
+ return rc;
}
else if ((i-1)%8 == 7 || i==len) {
dev_dbg(&adap->dev, "trans_wait len=%d i=%d\n",len,i);
@@ -264,9 +266,10 @@
*/
sis630_write(SMB_STS,0x10);
}
- if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) {
+ rc = sis630_transaction_wait(adap,
+ SIS630_BLOCK_DATA);
+ if (rc) {
dev_dbg(&adap->dev, "trans_wait failed\n");
- rc = -1;
break;
}
}
@@ -275,13 +278,14 @@
else {
/* read request */
data->block[0] = len = 0;
- if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock)) {
- return -1;
- }
+ rc = sis630_transaction_start(adap,
+ SIS630_BLOCK_DATA, &oldclock);
+ if (rc)
+ return rc;
do {
- if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) {
+ rc = sis630_transaction_wait(adap, SIS630_BLOCK_DATA);
+ if (rc) {
dev_dbg(&adap->dev, "trans_wait failed\n");
- rc = -1;
break;
}
/* if this first transaction then read byte count */
@@ -311,11 +315,13 @@
return rc;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 sis630_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data *data)
{
+ int status;
+
switch (size) {
case I2C_SMBUS_QUICK:
sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01));
@@ -350,13 +356,13 @@
size = SIS630_BLOCK_DATA;
return sis630_block_data(adap, data, read_write);
default:
- printk("Unsupported I2C size\n");
- return -1;
- break;
+ printk("Unsupported SMBus operation\n");
+ return -EOPNOTSUPP;
}
- if (sis630_transaction(adap, size))
- return -1;
+ status = sis630_transaction(adap, size);
+ if (status)
+ return status;
if ((size != SIS630_PCALL) &&
((read_write == I2C_SMBUS_WRITE) || (size == SIS630_QUICK))) {
@@ -373,8 +379,7 @@
data->word = sis630_read(SMB_BYTE) + (sis630_read(SMB_BYTE + 1) << 8);
break;
default:
- return -1;
- break;
+ return -EOPNOTSUPP;
}
return 0;
diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c
index dc235bb..29757b2 100644
--- a/drivers/i2c/busses/i2c-sis96x.c
+++ b/drivers/i2c/busses/i2c-sis96x.c
@@ -111,7 +111,7 @@
/* check it again */
if (((temp = sis96x_read(SMB_CNT)) & 0x03) != 0x00) {
dev_dbg(&sis96x_adapter.dev, "Failed (0x%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&sis96x_adapter.dev, "Successful\n");
}
@@ -136,19 +136,19 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_dbg(&sis96x_adapter.dev, "SMBus Timeout! (0x%02x)\n", temp);
- result = -1;
+ result = -ETIMEDOUT;
}
/* device error - probably missing ACK */
if (temp & 0x02) {
dev_dbg(&sis96x_adapter.dev, "Failed bus transaction!\n");
- result = -1;
+ result = -ENXIO;
}
/* bus collision */
if (temp & 0x04) {
dev_dbg(&sis96x_adapter.dev, "Bus collision!\n");
- result = -1;
+ result = -EIO;
}
/* Finish up by resetting the bus */
@@ -161,11 +161,12 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 sis96x_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data * data)
{
+ int status;
switch (size) {
case I2C_SMBUS_QUICK:
@@ -203,17 +204,17 @@
case I2C_SMBUS_BLOCK_DATA:
/* TO DO: */
dev_info(&adap->dev, "SMBus block not implemented!\n");
- return -1;
+ return -EOPNOTSUPP;
break;
default:
- dev_info(&adap->dev, "Unsupported I2C size\n");
- return -1;
- break;
+ dev_info(&adap->dev, "Unsupported SMBus operation\n");
+ return -EOPNOTSUPP;
}
- if (sis96x_transaction(size))
- return -1;
+ status = sis96x_transaction(size);
+ if (status)
+ return status;
if ((size != SIS96x_PROC_CALL) &&
((read_write == I2C_SMBUS_WRITE) || (size == SIS96x_QUICK)))
diff --git a/drivers/i2c/busses/i2c-stub.c b/drivers/i2c/busses/i2c-stub.c
index d08eeec..e37ccd8 100644
--- a/drivers/i2c/busses/i2c-stub.c
+++ b/drivers/i2c/busses/i2c-stub.c
@@ -43,7 +43,7 @@
static struct stub_chip *stub_chips;
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags,
char read_write, u8 command, int size, union i2c_smbus_data * data)
{
@@ -120,7 +120,7 @@
default:
dev_dbg(&adap->dev, "Unsupported I2C/SMBus command\n");
- ret = -1;
+ ret = -EOPNOTSUPP;
break;
} /* switch (size) */
diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c
index 77b13d0..7628fe8 100644
--- a/drivers/i2c/busses/i2c-viapro.c
+++ b/drivers/i2c/busses/i2c-viapro.c
@@ -152,7 +152,7 @@
if ((temp = inb_p(SMBHSTSTS)) & 0x1F) {
dev_err(&vt596_adapter.dev, "SMBus reset failed! "
"(0x%02x)\n", temp);
- return -1;
+ return -EBUSY;
}
}
@@ -167,24 +167,24 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&vt596_adapter.dev, "SMBus timeout!\n");
}
if (temp & 0x10) {
- result = -1;
+ result = -EIO;
dev_err(&vt596_adapter.dev, "Transaction failed (0x%02x)\n",
size);
}
if (temp & 0x08) {
- result = -1;
+ result = -EIO;
dev_err(&vt596_adapter.dev, "SMBus collision!\n");
}
if (temp & 0x04) {
int read = inb_p(SMBHSTADD) & 0x01;
- result = -1;
+ result = -ENXIO;
/* The quick and receive byte commands are used to probe
for chips, so errors are expected, and we don't want
to frighten the user. */
@@ -202,12 +202,13 @@
return result;
}
-/* Return -1 on error, 0 on success */
+/* Return negative errno on error, 0 on success */
static s32 vt596_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data *data)
{
int i;
+ int status;
switch (size) {
case I2C_SMBUS_QUICK:
@@ -258,8 +259,9 @@
outb_p(((addr & 0x7f) << 1) | read_write, SMBHSTADD);
- if (vt596_transaction(size)) /* Error in transaction */
- return -1;
+ status = vt596_transaction(size);
+ if (status)
+ return status;
if ((read_write == I2C_SMBUS_WRITE) || (size == VT596_QUICK))
return 0;
@@ -287,7 +289,7 @@
exit_unsupported:
dev_warn(&vt596_adapter.dev, "Unsupported command invoked! (0x%02x)\n",
size);
- return -1;
+ return -EOPNOTSUPP;
}
static u32 vt596_func(struct i2c_adapter *adapter)