| /* |
| * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| |
| #ifndef UFS_QCOM_PHY_QMP_14NM_H_ |
| #define UFS_QCOM_PHY_QMP_14NM_H_ |
| |
| #include "phy-qcom-ufs-i.h" |
| |
| /* QCOM UFS PHY control registers */ |
| #define COM_OFF(x) (0x000 + x) |
| #define PHY_OFF(x) (0xC00 + x) |
| #define TX_OFF(n, x) (0x400 + (0x400 * n) + x) |
| #define RX_OFF(n, x) (0x600 + (0x400 * n) + x) |
| |
| /* UFS PHY QSERDES COM registers */ |
| #define QSERDES_COM_BG_TIMER COM_OFF(0x0C) |
| #define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x34) |
| #define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x3C) |
| #define QSERDES_COM_PLL_IVCO COM_OFF(0x48) |
| #define QSERDES_COM_LOCK_CMP1_MODE0 COM_OFF(0x4C) |
| #define QSERDES_COM_LOCK_CMP2_MODE0 COM_OFF(0x50) |
| #define QSERDES_COM_LOCK_CMP3_MODE0 COM_OFF(0x54) |
| #define QSERDES_COM_LOCK_CMP1_MODE1 COM_OFF(0x58) |
| #define QSERDES_COM_LOCK_CMP2_MODE1 COM_OFF(0x5C) |
| #define QSERDES_COM_LOCK_CMP3_MODE1 COM_OFF(0x60) |
| #define QSERDES_COM_BG_TRIM COM_OFF(0x70) |
| #define QSERDES_COM_CP_CTRL_MODE0 COM_OFF(0x78) |
| #define QSERDES_COM_CP_CTRL_MODE1 COM_OFF(0x7C) |
| #define QSERDES_COM_PLL_RCTRL_MODE0 COM_OFF(0x84) |
| #define QSERDES_COM_PLL_RCTRL_MODE1 COM_OFF(0x88) |
| #define QSERDES_COM_PLL_CCTRL_MODE0 COM_OFF(0x90) |
| #define QSERDES_COM_PLL_CCTRL_MODE1 COM_OFF(0x94) |
| #define QSERDES_COM_SYSCLK_EN_SEL COM_OFF(0xAC) |
| #define QSERDES_COM_RESETSM_CNTRL COM_OFF(0xB4) |
| #define QSERDES_COM_RESCODE_DIV_NUM COM_OFF(0xC4) |
| #define QSERDES_COM_LOCK_CMP_EN COM_OFF(0xC8) |
| #define QSERDES_COM_LOCK_CMP_CFG COM_OFF(0xCC) |
| #define QSERDES_COM_DEC_START_MODE0 COM_OFF(0xD0) |
| #define QSERDES_COM_DEC_START_MODE1 COM_OFF(0xD4) |
| #define QSERDES_COM_DIV_FRAC_START1_MODE0 COM_OFF(0xDC) |
| #define QSERDES_COM_DIV_FRAC_START2_MODE0 COM_OFF(0xE0) |
| #define QSERDES_COM_DIV_FRAC_START3_MODE0 COM_OFF(0xE4) |
| #define QSERDES_COM_DIV_FRAC_START1_MODE1 COM_OFF(0xE8) |
| #define QSERDES_COM_DIV_FRAC_START2_MODE1 COM_OFF(0xEC) |
| #define QSERDES_COM_DIV_FRAC_START3_MODE1 COM_OFF(0xF0) |
| #define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 COM_OFF(0x108) |
| #define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 COM_OFF(0x10C) |
| #define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 COM_OFF(0x110) |
| #define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 COM_OFF(0x114) |
| #define QSERDES_COM_VCO_TUNE_CTRL COM_OFF(0x124) |
| #define QSERDES_COM_VCO_TUNE_MAP COM_OFF(0x128) |
| #define QSERDES_COM_VCO_TUNE1_MODE0 COM_OFF(0x12C) |
| #define QSERDES_COM_VCO_TUNE2_MODE0 COM_OFF(0x130) |
| #define QSERDES_COM_VCO_TUNE1_MODE1 COM_OFF(0x134) |
| #define QSERDES_COM_VCO_TUNE2_MODE1 COM_OFF(0x138) |
| #define QSERDES_COM_VCO_TUNE_INITVAL1 COM_OFF(0x13C) |
| #define QSERDES_COM_VCO_TUNE_INITVAL2 COM_OFF(0x140) |
| #define QSERDES_COM_VCO_TUNE_TIMER1 COM_OFF(0x144) |
| #define QSERDES_COM_VCO_TUNE_TIMER2 COM_OFF(0x148) |
| #define QSERDES_COM_CLK_SELECT COM_OFF(0x174) |
| #define QSERDES_COM_HSCLK_SEL COM_OFF(0x178) |
| #define QSERDES_COM_CORECLK_DIV COM_OFF(0x184) |
| #define QSERDES_COM_SW_RESET COM_OFF(0x188) |
| #define QSERDES_COM_CORE_CLK_EN COM_OFF(0x18C) |
| #define QSERDES_COM_CMN_CONFIG COM_OFF(0x194) |
| #define QSERDES_COM_SVS_MODE_CLK_SEL COM_OFF(0x19C) |
| #define QSERDES_COM_DEBUG_BUS0 COM_OFF(0x1A0) |
| #define QSERDES_COM_DEBUG_BUS1 COM_OFF(0x1A4) |
| #define QSERDES_COM_DEBUG_BUS2 COM_OFF(0x1A8) |
| #define QSERDES_COM_DEBUG_BUS3 COM_OFF(0x1AC) |
| #define QSERDES_COM_DEBUG_BUS_SEL COM_OFF(0x1B0) |
| #define QSERDES_COM_CMN_MISC2 COM_OFF(0x1B8) |
| #define QSERDES_COM_CORECLK_DIV_MODE1 COM_OFF(0x1BC) |
| |
| /* UFS PHY registers */ |
| #define UFS_PHY_PHY_START PHY_OFF(0x00) |
| #define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x04) |
| #define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x34) |
| #define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x3C) |
| #define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAP PHY_OFF(0xCC) |
| #define UFS_PHY_LINECFG_DISABLE PHY_OFF(0x138) |
| #define UFS_PHY_RX_SYM_RESYNC_CTRL PHY_OFF(0x13C) |
| #define UFS_PHY_RX_SIGDET_CTRL2 PHY_OFF(0x148) |
| #define UFS_PHY_RX_PWM_GEAR_BAND PHY_OFF(0x154) |
| #define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x168) |
| |
| /* UFS PHY TX registers */ |
| #define QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN TX_OFF(0, 0x68) |
| #define QSERDES_TX_LANE_MODE TX_OFF(0, 0x94) |
| |
| /* UFS PHY RX registers */ |
| #define QSERDES_RX_UCDR_SVS_SO_GAIN_HALF RX_OFF(0, 0x30) |
| #define QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER RX_OFF(0, 0x34) |
| #define QSERDES_RX_UCDR_SVS_SO_GAIN_EIGHTH RX_OFF(0, 0x38) |
| #define QSERDES_RX_UCDR_SVS_SO_GAIN RX_OFF(0, 0x3C) |
| #define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN RX_OFF(0, 0x40) |
| #define QSERDES_RX_UCDR_SO_SATURATION_ENABLE RX_OFF(0, 0x48) |
| #define QSERDES_RX_RX_TERM_BW RX_OFF(0, 0x90) |
| #define QSERDES_RX_RX_EQ_GAIN1_LSB RX_OFF(0, 0xC4) |
| #define QSERDES_RX_RX_EQ_GAIN1_MSB RX_OFF(0, 0xC8) |
| #define QSERDES_RX_RX_EQ_GAIN2_LSB RX_OFF(0, 0xCC) |
| #define QSERDES_RX_RX_EQ_GAIN2_MSB RX_OFF(0, 0xD0) |
| #define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 RX_OFF(0, 0xD8) |
| #define QSERDES_RX_SIGDET_CNTRL RX_OFF(0, 0x114) |
| #define QSERDES_RX_SIGDET_LVL RX_OFF(0, 0x118) |
| #define QSERDES_RX_SIGDET_DEGLITCH_CNTRL RX_OFF(0, 0x11C) |
| #define QSERDES_RX_RX_INTERFACE_MODE RX_OFF(0, 0x12C) |
| |
| #define UFS_PHY_RX_LINECFG_DISABLE_BIT BIT(1) |
| |
| /* |
| * This structure represents the 14nm specific phy. |
| * common_cfg MUST remain the first field in this structure |
| * in case extra fields are added. This way, when calling |
| * get_ufs_qcom_phy() of generic phy, we can extract the |
| * common phy structure (struct ufs_qcom_phy) out of it |
| * regardless of the relevant specific phy. |
| */ |
| struct ufs_qcom_phy_qmp_14nm { |
| struct ufs_qcom_phy common_cfg; |
| }; |
| |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_2_0_0[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_CONFIG, 0x0e), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x17), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CLK_SELECT, 0x30), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TIMER, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_HSCLK_SEL, 0x05), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_EN, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_CTRL, 0x1C), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x20), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_EN, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_CFG, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x14), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE0, 0x82), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE0, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE0, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE0, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE0, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE1, 0x98), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE1, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE1, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE1, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE1, 0x32), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE1, 0x00), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN, 0x45), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE, 0x06), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_LVL, 0x24), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x1E), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_BW, 0x5B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0D), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IVCO, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TRIM, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESCODE_DIV_NUM, 0x15), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MISC2, 0x1F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_HALF, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_SATURATION_ENABLE, 0x4B), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL2, 0x6c), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x12), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x06), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAP, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYM_RESYNC_CTRL, 0x03), |
| |
| /* |
| * UFS_PHY_RX_PWM_GEAR_BAND configuration is changed after the power up |
| * sequence so make sure that this register gets set to power on reset |
| * value. This is required in case power up sequence is initiated after |
| * this register value got changed to value other than power on reset |
| * value. |
| */ |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWM_GEAR_BAND, 0x55), |
| }; |
| |
| /* |
| * For 2.1.0 revision, SVS mode configuration can be part of PHY power |
| * up sequence itself. |
| */ |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_2_1_0[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_CONFIG, 0x0e), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x14), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CLK_SELECT, 0x30), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TIMER, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_HSCLK_SEL, 0x05), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_EN, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_CTRL, 0x10), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x20), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_EN, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_CFG, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x14), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE0, 0x82), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE0, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE0, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE0, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE0, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE1, 0x98), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE1, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE1, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE1, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE1, 0x32), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE1, 0x00), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN, 0x45), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE, 0x06), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_LVL, 0x24), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x40), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x1E), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_BW, 0x5B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0D), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IVCO, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TRIM, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWM_GEAR_BAND, 0x15), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESCODE_DIV_NUM, 0x15), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MISC2, 0x1F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_HALF, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_SATURATION_ENABLE, 0x4B), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL2, 0x6c), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x12), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x06), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAP, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYM_RESYNC_CTRL, 0x03), |
| }; |
| |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_2_2_0[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_CONFIG, 0x0e), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x14), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CLK_SELECT, 0x30), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TIMER, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_HSCLK_SEL, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_EN, 0x01), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_CTRL, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x20), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_EN, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_CFG, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER1, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE0, 0x82), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE0, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE0, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE0, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE0, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE0, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE0, 0xff), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE0, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE1, 0x98), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE1, 0x0b), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE1, 0x16), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE1, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE1, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE1, 0x32), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE1, 0x00), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN, 0x45), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE, 0x06), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_LVL, 0x24), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x40), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x1E), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_BW, 0x5B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x3F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0D), |
| |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IVCO, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TRIM, 0x0F), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWM_GEAR_BAND, 0x15), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESCODE_DIV_NUM, 0x40), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MISC2, 0x63), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_HALF, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SVS_SO_GAIN, 0x04), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_SATURATION_ENABLE, 0x4B), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_INITVAL1, 0xFF), |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_INITVAL2, 0x00), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL2, 0x6c), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x0A), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x02), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAP, 0x28), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYM_RESYNC_CTRL, 0x03), |
| }; |
| |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x54), |
| }; |
| |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_B_2_2_0[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x44), |
| }; |
| |
| /* |
| * For 2.0.0 revision, apply this SVS mode configuration after PHY power |
| * up sequence is completed. |
| */ |
| static struct ufs_qcom_phy_calibration phy_svs_mode_config_2_0_0[] = { |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x40), |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWM_GEAR_BAND, 0x15), |
| }; |
| |
| #endif |