| /**************************************************************************** |
| * Driver for Solarflare Solarstorm network controllers and boards |
| * Copyright 2009-2011 Solarflare Communications Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License version 2 as published |
| * by the Free Software Foundation, incorporated herein by reference. |
| */ |
| |
| |
| #ifndef MCDI_PCOL_H |
| #define MCDI_PCOL_H |
| |
| /* Values to be written into FMCR_CZ_RESET_STATE_REG to control boot. */ |
| /* Power-on reset state */ |
| #define MC_FW_STATE_POR (1) |
| /* If this is set in MC_RESET_STATE_REG then it should be |
| * possible to jump into IMEM without loading code from flash. */ |
| #define MC_FW_WARM_BOOT_OK (2) |
| /* The MC main image has started to boot. */ |
| #define MC_FW_STATE_BOOTING (4) |
| /* The Scheduler has started. */ |
| #define MC_FW_STATE_SCHED (8) |
| |
| /* Values to be written to the per-port status dword in shared |
| * memory on reboot and assert */ |
| #define MC_STATUS_DWORD_REBOOT (0xb007b007) |
| #define MC_STATUS_DWORD_ASSERT (0xdeaddead) |
| |
| /* The current version of the MCDI protocol. |
| * |
| * Note that the ROM burnt into the card only talks V0, so at the very |
| * least every driver must support version 0 and MCDI_PCOL_VERSION |
| */ |
| #define MCDI_PCOL_VERSION 1 |
| |
| /** |
| * MCDI version 1 |
| * |
| * Each MCDI request starts with an MCDI_HEADER, which is a 32byte |
| * structure, filled in by the client. |
| * |
| * 0 7 8 16 20 22 23 24 31 |
| * | CODE | R | LEN | SEQ | Rsvd | E | R | XFLAGS | |
| * | | | |
| * | | \--- Response |
| * | \------- Error |
| * \------------------------------ Resync (always set) |
| * |
| * The client writes it's request into MC shared memory, and rings the |
| * doorbell. Each request is completed by either by the MC writting |
| * back into shared memory, or by writting out an event. |
| * |
| * All MCDI commands support completion by shared memory response. Each |
| * request may also contain additional data (accounted for by HEADER.LEN), |
| * and some response's may also contain additional data (again, accounted |
| * for by HEADER.LEN). |
| * |
| * Some MCDI commands support completion by event, in which any associated |
| * response data is included in the event. |
| * |
| * The protocol requires one response to be delivered for every request, a |
| * request should not be sent unless the response for the previous request |
| * has been received (either by polling shared memory, or by receiving |
| * an event). |
| */ |
| |
| /** Request/Response structure */ |
| #define MCDI_HEADER_OFST 0 |
| #define MCDI_HEADER_CODE_LBN 0 |
| #define MCDI_HEADER_CODE_WIDTH 7 |
| #define MCDI_HEADER_RESYNC_LBN 7 |
| #define MCDI_HEADER_RESYNC_WIDTH 1 |
| #define MCDI_HEADER_DATALEN_LBN 8 |
| #define MCDI_HEADER_DATALEN_WIDTH 8 |
| #define MCDI_HEADER_SEQ_LBN 16 |
| #define MCDI_HEADER_RSVD_LBN 20 |
| #define MCDI_HEADER_RSVD_WIDTH 2 |
| #define MCDI_HEADER_SEQ_WIDTH 4 |
| #define MCDI_HEADER_ERROR_LBN 22 |
| #define MCDI_HEADER_ERROR_WIDTH 1 |
| #define MCDI_HEADER_RESPONSE_LBN 23 |
| #define MCDI_HEADER_RESPONSE_WIDTH 1 |
| #define MCDI_HEADER_XFLAGS_LBN 24 |
| #define MCDI_HEADER_XFLAGS_WIDTH 8 |
| /* Request response using event */ |
| #define MCDI_HEADER_XFLAGS_EVREQ 0x01 |
| |
| /* Maximum number of payload bytes */ |
| #define MCDI_CTL_SDU_LEN_MAX 0xfc |
| |
| /* The MC can generate events for two reasons: |
| * - To complete a shared memory request if XFLAGS_EVREQ was set |
| * - As a notification (link state, i2c event), controlled |
| * via MC_CMD_LOG_CTRL |
| * |
| * Both events share a common structure: |
| * |
| * 0 32 33 36 44 52 60 |
| * | Data | Cont | Level | Src | Code | Rsvd | |
| * | |
| * \ There is another event pending in this notification |
| * |
| * If Code==CMDDONE, then the fields are further interpreted as: |
| * |
| * - LEVEL==INFO Command succeded |
| * - LEVEL==ERR Command failed |
| * |
| * 0 8 16 24 32 |
| * | Seq | Datalen | Errno | Rsvd | |
| * |
| * These fields are taken directly out of the standard MCDI header, i.e., |
| * LEVEL==ERR, Datalen == 0 => Reboot |
| * |
| * Events can be squirted out of the UART (using LOG_CTRL) without a |
| * MCDI header. An event can be distinguished from a MCDI response by |
| * examining the first byte which is 0xc0. This corresponds to the |
| * non-existent MCDI command MC_CMD_DEBUG_LOG. |
| * |
| * 0 7 8 |
| * | command | Resync | = 0xc0 |
| * |
| * Since the event is written in big-endian byte order, this works |
| * providing bits 56-63 of the event are 0xc0. |
| * |
| * 56 60 63 |
| * | Rsvd | Code | = 0xc0 |
| * |
| * Which means for convenience the event code is 0xc for all MC |
| * generated events. |
| */ |
| #define FSE_AZ_EV_CODE_MCDI_EVRESPONSE 0xc |
| |
| #define MCDI_EVENT_DATA_LBN 0 |
| #define MCDI_EVENT_DATA_WIDTH 32 |
| #define MCDI_EVENT_CONT_LBN 32 |
| #define MCDI_EVENT_CONT_WIDTH 1 |
| #define MCDI_EVENT_LEVEL_LBN 33 |
| #define MCDI_EVENT_LEVEL_WIDTH 3 |
| #define MCDI_EVENT_LEVEL_INFO (0) |
| #define MCDI_EVENT_LEVEL_WARN (1) |
| #define MCDI_EVENT_LEVEL_ERR (2) |
| #define MCDI_EVENT_LEVEL_FATAL (3) |
| #define MCDI_EVENT_SRC_LBN 36 |
| #define MCDI_EVENT_SRC_WIDTH 8 |
| #define MCDI_EVENT_CODE_LBN 44 |
| #define MCDI_EVENT_CODE_WIDTH 8 |
| #define MCDI_EVENT_CODE_BADSSERT (1) |
| #define MCDI_EVENT_CODE_PMNOTICE (2) |
| #define MCDI_EVENT_CODE_CMDDONE (3) |
| #define MCDI_EVENT_CMDDONE_SEQ_LBN 0 |
| #define MCDI_EVENT_CMDDONE_SEQ_WIDTH 8 |
| #define MCDI_EVENT_CMDDONE_DATALEN_LBN 8 |
| #define MCDI_EVENT_CMDDONE_DATALEN_WIDTH 8 |
| #define MCDI_EVENT_CMDDONE_ERRNO_LBN 16 |
| #define MCDI_EVENT_CMDDONE_ERRNO_WIDTH 8 |
| #define MCDI_EVENT_CODE_LINKCHANGE (4) |
| #define MCDI_EVENT_LINKCHANGE_LP_CAP_LBN 0 |
| #define MCDI_EVENT_LINKCHANGE_LP_CAP_WIDTH 16 |
| #define MCDI_EVENT_LINKCHANGE_SPEED_LBN 16 |
| #define MCDI_EVENT_LINKCHANGE_SPEED_WIDTH 4 |
| #define MCDI_EVENT_LINKCHANGE_SPEED_100M 1 |
| #define MCDI_EVENT_LINKCHANGE_SPEED_1G 2 |
| #define MCDI_EVENT_LINKCHANGE_SPEED_10G 3 |
| #define MCDI_EVENT_LINKCHANGE_FCNTL_LBN 20 |
| #define MCDI_EVENT_LINKCHANGE_FCNTL_WIDTH 4 |
| #define MCDI_EVENT_LINKCHANGE_LINK_FLAGS_LBN 24 |
| #define MCDI_EVENT_LINKCHANGE_LINK_FLAGS_WIDTH 8 |
| #define MCDI_EVENT_CODE_SENSOREVT (5) |
| #define MCDI_EVENT_SENSOREVT_MONITOR_LBN 0 |
| #define MCDI_EVENT_SENSOREVT_MONITOR_WIDTH 8 |
| #define MCDI_EVENT_SENSOREVT_STATE_LBN 8 |
| #define MCDI_EVENT_SENSOREVT_STATE_WIDTH 8 |
| #define MCDI_EVENT_SENSOREVT_VALUE_LBN 16 |
| #define MCDI_EVENT_SENSOREVT_VALUE_WIDTH 16 |
| #define MCDI_EVENT_CODE_SCHEDERR (6) |
| #define MCDI_EVENT_CODE_REBOOT (7) |
| #define MCDI_EVENT_CODE_MAC_STATS_DMA (8) |
| #define MCDI_EVENT_MAC_STATS_DMA_GENERATION_LBN 0 |
| #define MCDI_EVENT_MAC_STATS_DMA_GENERATION_WIDTH 32 |
| |
| /* Non-existent command target */ |
| #define MC_CMD_ERR_ENOENT 2 |
| /* assert() has killed the MC */ |
| #define MC_CMD_ERR_EINTR 4 |
| /* Caller does not hold required locks */ |
| #define MC_CMD_ERR_EACCES 13 |
| /* Resource is currently unavailable (e.g. lock contention) */ |
| #define MC_CMD_ERR_EBUSY 16 |
| /* Invalid argument to target */ |
| #define MC_CMD_ERR_EINVAL 22 |
| /* Non-recursive resource is already acquired */ |
| #define MC_CMD_ERR_EDEADLK 35 |
| /* Operation not implemented */ |
| #define MC_CMD_ERR_ENOSYS 38 |
| /* Operation timed out */ |
| #define MC_CMD_ERR_ETIME 62 |
| |
| #define MC_CMD_ERR_CODE_OFST 0 |
| |
| |
| /* MC_CMD_READ32: (debug, variadic out) |
| * Read multiple 32byte words from MC memory |
| */ |
| #define MC_CMD_READ32 0x01 |
| #define MC_CMD_READ32_IN_LEN 8 |
| #define MC_CMD_READ32_IN_ADDR_OFST 0 |
| #define MC_CMD_READ32_IN_NUMWORDS_OFST 4 |
| #define MC_CMD_READ32_OUT_LEN(_numwords) \ |
| (4 * (_numwords)) |
| #define MC_CMD_READ32_OUT_BUFFER_OFST 0 |
| |
| /* MC_CMD_WRITE32: (debug, variadic in) |
| * Write multiple 32byte words to MC memory |
| */ |
| #define MC_CMD_WRITE32 0x02 |
| #define MC_CMD_WRITE32_IN_LEN(_numwords) (((_numwords) * 4) + 4) |
| #define MC_CMD_WRITE32_IN_ADDR_OFST 0 |
| #define MC_CMD_WRITE32_IN_BUFFER_OFST 4 |
| #define MC_CMD_WRITE32_OUT_LEN 0 |
| |
| /* MC_CMD_COPYCODE: (debug) |
| * Copy MC code between two locations and jump |
| */ |
| #define MC_CMD_COPYCODE 0x03 |
| #define MC_CMD_COPYCODE_IN_LEN 16 |
| #define MC_CMD_COPYCODE_IN_SRC_ADDR_OFST 0 |
| #define MC_CMD_COPYCODE_IN_DEST_ADDR_OFST 4 |
| #define MC_CMD_COPYCODE_IN_NUMWORDS_OFST 8 |
| #define MC_CMD_COPYCODE_IN_JUMP_OFST 12 |
| /* Control should return to the caller rather than jumping */ |
| #define MC_CMD_COPYCODE_JUMP_NONE 1 |
| #define MC_CMD_COPYCODE_OUT_LEN 0 |
| |
| /* MC_CMD_SET_FUNC: (debug) |
| * Select function for function-specific commands. |
| */ |
| #define MC_CMD_SET_FUNC 0x04 |
| #define MC_CMD_SET_FUNC_IN_LEN 4 |
| #define MC_CMD_SET_FUNC_IN_FUNC_OFST 0 |
| #define MC_CMD_SET_FUNC_OUT_LEN 0 |
| |
| /* MC_CMD_GET_BOOT_STATUS: |
| * Get the instruction address from which the MC booted. |
| */ |
| #define MC_CMD_GET_BOOT_STATUS 0x05 |
| #define MC_CMD_GET_BOOT_STATUS_IN_LEN 0 |
| #define MC_CMD_GET_BOOT_STATUS_OUT_LEN 8 |
| #define MC_CMD_GET_BOOT_STATUS_OUT_BOOT_OFFSET_OFST 0 |
| #define MC_CMD_GET_BOOT_STATUS_OUT_FLAGS_OFST 4 |
| /* Reboot caused by watchdog */ |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_LBN (0) |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_WATCHDOG_WIDTH (1) |
| /* MC booted from primary flash partition */ |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_LBN (1) |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_PRIMARY_WIDTH (1) |
| /* MC booted from backup flash partition */ |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_LBN (2) |
| #define MC_CMD_GET_BOOT_STATUS_FLAGS_BACKUP_WIDTH (1) |
| |
| /* MC_CMD_GET_ASSERTS: (debug, variadic out) |
| * Get (and optionally clear) the current assertion status. |
| * |
| * Only OUT.GLOBAL_FLAGS is guaranteed to exist in the completion |
| * payload. The other fields will only be present if |
| * OUT.GLOBAL_FLAGS != NO_FAILS |
| */ |
| #define MC_CMD_GET_ASSERTS 0x06 |
| #define MC_CMD_GET_ASSERTS_IN_LEN 4 |
| #define MC_CMD_GET_ASSERTS_IN_CLEAR_OFST 0 |
| #define MC_CMD_GET_ASSERTS_OUT_LEN 140 |
| /* Assertion status flag */ |
| #define MC_CMD_GET_ASSERTS_OUT_GLOBAL_FLAGS_OFST 0 |
| /*! No assertions have failed. */ |
| #define MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS 1 |
| /*! A system-level assertion has failed. */ |
| #define MC_CMD_GET_ASSERTS_FLAGS_SYS_FAIL 2 |
| /*! A thread-level assertion has failed. */ |
| #define MC_CMD_GET_ASSERTS_FLAGS_THR_FAIL 3 |
| /*! The system was reset by the watchdog. */ |
| #define MC_CMD_GET_ASSERTS_FLAGS_WDOG_FIRED 4 |
| /* Failing PC value */ |
| #define MC_CMD_GET_ASSERTS_OUT_SAVED_PC_OFFS_OFST 4 |
| /* Saved GP regs */ |
| #define MC_CMD_GET_ASSERTS_OUT_GP_REGS_OFFS_OFST 8 |
| #define MC_CMD_GET_ASSERTS_OUT_GP_REGS_LEN 124 |
| /* Failing thread address */ |
| #define MC_CMD_GET_ASSERTS_OUT_THREAD_OFFS_OFST 132 |
| |
| /* MC_CMD_LOG_CTRL: |
| * Determine the output stream for various events and messages |
| */ |
| #define MC_CMD_LOG_CTRL 0x07 |
| #define MC_CMD_LOG_CTRL_IN_LEN 8 |
| #define MC_CMD_LOG_CTRL_IN_LOG_DEST_OFST 0 |
| #define MC_CMD_LOG_CTRL_IN_LOG_DEST_UART (1) |
| #define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ (2) |
| #define MC_CMD_LOG_CTRL_IN_LOG_DEST_EVQ_OFST 4 |
| #define MC_CMD_LOG_CTRL_OUT_LEN 0 |
| |
| /* MC_CMD_GET_VERSION: |
| * Get version information about the MC firmware |
| */ |
| #define MC_CMD_GET_VERSION 0x08 |
| #define MC_CMD_GET_VERSION_IN_LEN 0 |
| #define MC_CMD_GET_VERSION_V0_OUT_LEN 4 |
| #define MC_CMD_GET_VERSION_V1_OUT_LEN 32 |
| #define MC_CMD_GET_VERSION_OUT_FIRMWARE_OFST 0 |
| /* Reserved version number to indicate "any" version. */ |
| #define MC_CMD_GET_VERSION_OUT_FIRMWARE_ANY 0xffffffff |
| /* The version response of a boot ROM awaiting rescue */ |
| #define MC_CMD_GET_VERSION_OUT_FIRMWARE_BOOTROM 0xb0070000 |
| #define MC_CMD_GET_VERSION_V1_OUT_PCOL_OFST 4 |
| /* 128bit mask of functions supported by the current firmware */ |
| #define MC_CMD_GET_VERSION_V1_OUT_SUPPORTED_FUNCS_OFST 8 |
| /* The command set exported by the boot ROM (MCDI v0) */ |
| #define MC_CMD_GET_VERSION_V0_SUPPORTED_FUNCS { \ |
| (1 << MC_CMD_READ32) | \ |
| (1 << MC_CMD_WRITE32) | \ |
| (1 << MC_CMD_COPYCODE) | \ |
| (1 << MC_CMD_GET_VERSION), \ |
| 0, 0, 0 } |
| #define MC_CMD_GET_VERSION_OUT_VERSION_OFST 24 |
| |
| /* Vectors in the boot ROM */ |
| /* Point to the copycode entry point. */ |
| #define MC_BOOTROM_COPYCODE_VEC (0x7f4) |
| /* Points to the recovery mode entry point. */ |
| #define MC_BOOTROM_NOFLASH_VEC (0x7f8) |
| |
| /* Test execution limits */ |
| #define MC_TESTEXEC_VARIANT_COUNT 16 |
| #define MC_TESTEXEC_RESULT_COUNT 7 |
| |
| /* MC_CMD_SET_TESTVARS: (debug, variadic in) |
| * Write variant words for test. |
| * |
| * The user supplies a bitmap of the variants they wish to set. |
| * They must ensure that IN.LEN >= 4 + 4 * ffs(BITMAP) |
| */ |
| #define MC_CMD_SET_TESTVARS 0x09 |
| #define MC_CMD_SET_TESTVARS_IN_LEN(_numwords) \ |
| (4 + 4*(_numwords)) |
| #define MC_CMD_SET_TESTVARS_IN_ARGS_BITMAP_OFST 0 |
| /* Up to MC_TESTEXEC_VARIANT_COUNT of 32byte words start here */ |
| #define MC_CMD_SET_TESTVARS_IN_ARGS_BUFFER_OFST 4 |
| #define MC_CMD_SET_TESTVARS_OUT_LEN 0 |
| |
| /* MC_CMD_GET_TESTRCS: (debug, variadic out) |
| * Return result words from test. |
| */ |
| #define MC_CMD_GET_TESTRCS 0x0a |
| #define MC_CMD_GET_TESTRCS_IN_LEN 4 |
| #define MC_CMD_GET_TESTRCS_IN_NUMWORDS_OFST 0 |
| #define MC_CMD_GET_TESTRCS_OUT_LEN(_numwords) \ |
| (4 * (_numwords)) |
| #define MC_CMD_GET_TESTRCS_OUT_BUFFER_OFST 0 |
| |
| /* MC_CMD_RUN_TEST: (debug) |
| * Run the test exported by this firmware image |
| */ |
| #define MC_CMD_RUN_TEST 0x0b |
| #define MC_CMD_RUN_TEST_IN_LEN 0 |
| #define MC_CMD_RUN_TEST_OUT_LEN 0 |
| |
| /* MC_CMD_CSR_READ32: (debug, variadic out) |
| * Read 32bit words from the indirect memory map |
| */ |
| #define MC_CMD_CSR_READ32 0x0c |
| #define MC_CMD_CSR_READ32_IN_LEN 12 |
| #define MC_CMD_CSR_READ32_IN_ADDR_OFST 0 |
| #define MC_CMD_CSR_READ32_IN_STEP_OFST 4 |
| #define MC_CMD_CSR_READ32_IN_NUMWORDS_OFST 8 |
| #define MC_CMD_CSR_READ32_OUT_LEN(_numwords) \ |
| (((_numwords) * 4) + 4) |
| /* IN.NUMWORDS of 32bit words start here */ |
| #define MC_CMD_CSR_READ32_OUT_BUFFER_OFST 0 |
| #define MC_CMD_CSR_READ32_OUT_IREG_STATUS_OFST(_numwords) \ |
| ((_numwords) * 4) |
| |
| /* MC_CMD_CSR_WRITE32: (debug, variadic in) |
| * Write 32bit dwords to the indirect memory map |
| */ |
| #define MC_CMD_CSR_WRITE32 0x0d |
| #define MC_CMD_CSR_WRITE32_IN_LEN(_numwords) \ |
| (((_numwords) * 4) + 8) |
| #define MC_CMD_CSR_WRITE32_IN_ADDR_OFST 0 |
| #define MC_CMD_CSR_WRITE32_IN_STEP_OFST 4 |
| /* Multiple 32bit words of data to write start here */ |
| #define MC_CMD_CSR_WRITE32_IN_BUFFER_OFST 8 |
| #define MC_CMD_CSR_WRITE32_OUT_LEN 4 |
| #define MC_CMD_CSR_WRITE32_OUT_STATUS_OFST 0 |
| |
| /* MC_CMD_JTAG_WORK: (debug, fpga only) |
| * Process JTAG work buffer for RBF acceleration. |
| * |
| * Host: bit count, (up to) 32 words of data to clock out to JTAG |
| * (bits 1,0=TMS,TDO for first bit; bits 3,2=TMS,TDO for second bit, etc.) |
| * MC: bit count, (up to) 32 words of data clocked in from JTAG |
| * (bit 0=TDI for first bit, bit 1=TDI for second bit, etc.; [31:16] unused) |
| */ |
| #define MC_CMD_JTAG_WORK 0x0e |
| |
| /* MC_CMD_STACKINFO: (debug, variadic out) |
| * Get stack information |
| * |
| * Host: nothing |
| * MC: (thread ptr, stack size, free space) for each thread in system |
| */ |
| #define MC_CMD_STACKINFO 0x0f |
| |
| /* MC_CMD_MDIO_READ: |
| * MDIO register read |
| */ |
| #define MC_CMD_MDIO_READ 0x10 |
| #define MC_CMD_MDIO_READ_IN_LEN 16 |
| #define MC_CMD_MDIO_READ_IN_BUS_OFST 0 |
| #define MC_CMD_MDIO_READ_IN_PRTAD_OFST 4 |
| #define MC_CMD_MDIO_READ_IN_DEVAD_OFST 8 |
| #define MC_CMD_MDIO_READ_IN_ADDR_OFST 12 |
| #define MC_CMD_MDIO_READ_OUT_LEN 8 |
| #define MC_CMD_MDIO_READ_OUT_VALUE_OFST 0 |
| #define MC_CMD_MDIO_READ_OUT_STATUS_OFST 4 |
| |
| /* MC_CMD_MDIO_WRITE: |
| * MDIO register write |
| */ |
| #define MC_CMD_MDIO_WRITE 0x11 |
| #define MC_CMD_MDIO_WRITE_IN_LEN 20 |
| #define MC_CMD_MDIO_WRITE_IN_BUS_OFST 0 |
| #define MC_CMD_MDIO_WRITE_IN_PRTAD_OFST 4 |
| #define MC_CMD_MDIO_WRITE_IN_DEVAD_OFST 8 |
| #define MC_CMD_MDIO_WRITE_IN_ADDR_OFST 12 |
| #define MC_CMD_MDIO_WRITE_IN_VALUE_OFST 16 |
| #define MC_CMD_MDIO_WRITE_OUT_LEN 4 |
| #define MC_CMD_MDIO_WRITE_OUT_STATUS_OFST 0 |
| |
| /* By default all the MCDI MDIO operations perform clause45 mode. |
| * If you want to use clause22 then set DEVAD = MC_CMD_MDIO_CLAUSE22. |
| */ |
| #define MC_CMD_MDIO_CLAUSE22 32 |
| |
| /* There are two MDIO buses: one for the internal PHY, and one for external |
| * devices. |
| */ |
| #define MC_CMD_MDIO_BUS_INTERNAL 0 |
| #define MC_CMD_MDIO_BUS_EXTERNAL 1 |
| |
| /* The MDIO commands return the raw status bits from the MDIO block. A "good" |
| * transaction should have the DONE bit set and all other bits clear. |
| */ |
| #define MC_CMD_MDIO_STATUS_GOOD 0x08 |
| |
| |
| /* MC_CMD_DBI_WRITE: (debug) |
| * Write DBI register(s) |
| * |
| * Host: address, byte-enables (and VF selection, and cs2 flag), |
| * value [,address ...] |
| * MC: nothing |
| */ |
| #define MC_CMD_DBI_WRITE 0x12 |
| #define MC_CMD_DBI_WRITE_IN_LEN(_numwords) \ |
| (12 * (_numwords)) |
| #define MC_CMD_DBI_WRITE_IN_ADDRESS_OFST(_word) \ |
| (((_word) * 12) + 0) |
| #define MC_CMD_DBI_WRITE_IN_BYTE_MASK_OFST(_word) \ |
| (((_word) * 12) + 4) |
| #define MC_CMD_DBI_WRITE_IN_VALUE_OFST(_word) \ |
| (((_word) * 12) + 8) |
| #define MC_CMD_DBI_WRITE_OUT_LEN 0 |
| |
| /* MC_CMD_DBI_READ: (debug) |
| * Read DBI register(s) |
| * |
| * Host: address, [,address ...] |
| * MC: value [,value ...] |
| * (note: this does not support reading from VFs, but is retained for backwards |
| * compatibility; see MC_CMD_DBI_READX below) |
| */ |
| #define MC_CMD_DBI_READ 0x13 |
| #define MC_CMD_DBI_READ_IN_LEN(_numwords) \ |
| (4 * (_numwords)) |
| #define MC_CMD_DBI_READ_OUT_LEN(_numwords) \ |
| (4 * (_numwords)) |
| |
| /* MC_CMD_PORT_READ32: (debug) |
| * Read a 32-bit register from the indirect port register map. |
| * |
| * The port to access is implied by the Shared memory channel used. |
| */ |
| #define MC_CMD_PORT_READ32 0x14 |
| #define MC_CMD_PORT_READ32_IN_LEN 4 |
| #define MC_CMD_PORT_READ32_IN_ADDR_OFST 0 |
| #define MC_CMD_PORT_READ32_OUT_LEN 8 |
| #define MC_CMD_PORT_READ32_OUT_VALUE_OFST 0 |
| #define MC_CMD_PORT_READ32_OUT_STATUS_OFST 4 |
| |
| /* MC_CMD_PORT_WRITE32: (debug) |
| * Write a 32-bit register to the indirect port register map. |
| * |
| * The port to access is implied by the Shared memory channel used. |
| */ |
| #define MC_CMD_PORT_WRITE32 0x15 |
| #define MC_CMD_PORT_WRITE32_IN_LEN 8 |
| #define MC_CMD_PORT_WRITE32_IN_ADDR_OFST 0 |
| #define MC_CMD_PORT_WRITE32_IN_VALUE_OFST 4 |
| #define MC_CMD_PORT_WRITE32_OUT_LEN 4 |
| #define MC_CMD_PORT_WRITE32_OUT_STATUS_OFST 0 |
| |
| /* MC_CMD_PORT_READ128: (debug) |
| * Read a 128-bit register from indirect port register map |
| * |
| * The port to access is implied by the Shared memory channel used. |
| */ |
| #define MC_CMD_PORT_READ128 0x16 |
| #define MC_CMD_PORT_READ128_IN_LEN 4 |
| #define MC_CMD_PORT_READ128_IN_ADDR_OFST 0 |
| #define MC_CMD_PORT_READ128_OUT_LEN 20 |
| #define MC_CMD_PORT_READ128_OUT_VALUE_OFST 0 |
| #define MC_CMD_PORT_READ128_OUT_STATUS_OFST 16 |
| |
| /* MC_CMD_PORT_WRITE128: (debug) |
| * Write a 128-bit register to indirect port register map. |
| * |
| * The port to access is implied by the Shared memory channel used. |
| */ |
| #define MC_CMD_PORT_WRITE128 0x17 |
| #define MC_CMD_PORT_WRITE128_IN_LEN 20 |
| #define MC_CMD_PORT_WRITE128_IN_ADDR_OFST 0 |
| #define MC_CMD_PORT_WRITE128_IN_VALUE_OFST 4 |
| #define MC_CMD_PORT_WRITE128_OUT_LEN 4 |
| #define MC_CMD_PORT_WRITE128_OUT_STATUS_OFST 0 |
| |
| /* MC_CMD_GET_BOARD_CFG: |
| * Returns the MC firmware configuration structure |
| * |
| * The FW_SUBTYPE_LIST contains a 16-bit value for each of the 12 types of |
| * NVRAM area. The values are defined in the firmware/mc/platform/<xxx>.c file |
| * for a specific board type, but otherwise have no meaning to the MC; they |
| * are used by the driver to manage selection of appropriate firmware updates. |
| */ |
| #define MC_CMD_GET_BOARD_CFG 0x18 |
| #define MC_CMD_GET_BOARD_CFG_IN_LEN 0 |
| #define MC_CMD_GET_BOARD_CFG_OUT_LEN 96 |
| #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_TYPE_OFST 0 |
| #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_OFST 4 |
| #define MC_CMD_GET_BOARD_CFG_OUT_BOARD_NAME_LEN 32 |
| #define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT0_OFST 36 |
| #define MC_CMD_GET_BOARD_CFG_OUT_CAPABILITIES_PORT1_OFST 40 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_OFST 44 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT0_LEN 6 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_OFST 50 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_ADDR_BASE_PORT1_LEN 6 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT0_OFST 56 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_COUNT_PORT1_OFST 60 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT0_OFST 64 |
| #define MC_CMD_GET_BOARD_CFG_OUT_MAC_STRIDE_PORT1_OFST 68 |
| #define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_OFST 72 |
| #define MC_CMD_GET_BOARD_CFG_OUT_FW_SUBTYPE_LIST_LEN 24 |
| |
| /* MC_CMD_DBI_READX: (debug) |
| * Read DBI register(s) -- extended functionality |
| * |
| * Host: vf selection, address, [,vf selection ...] |
| * MC: value [,value ...] |
| */ |
| #define MC_CMD_DBI_READX 0x19 |
| #define MC_CMD_DBI_READX_IN_LEN(_numwords) \ |
| (8*(_numwords)) |
| #define MC_CMD_DBI_READX_OUT_LEN(_numwords) \ |
| (4*(_numwords)) |
| |
| /* MC_CMD_SET_RAND_SEED: |
| * Set the 16byte seed for the MC psuedo-random generator |
| */ |
| #define MC_CMD_SET_RAND_SEED 0x1a |
| #define MC_CMD_SET_RAND_SEED_IN_LEN 16 |
| #define MC_CMD_SET_RAND_SEED_IN_SEED_OFST 0 |
| #define MC_CMD_SET_RAND_SEED_OUT_LEN 0 |
| |
| /* MC_CMD_LTSSM_HIST: (debug) |
| * Retrieve the history of the LTSSM, if the build supports it. |
| * |
| * Host: nothing |
| * MC: variable number of LTSSM values, as bytes |
| * The history is read-to-clear. |
| */ |
| #define MC_CMD_LTSSM_HIST 0x1b |
| |
| /* MC_CMD_DRV_ATTACH: |
| * Inform MCPU that this port is managed on the host (i.e. driver active) |
| */ |
| #define MC_CMD_DRV_ATTACH 0x1c |
| #define MC_CMD_DRV_ATTACH_IN_LEN 8 |
| #define MC_CMD_DRV_ATTACH_IN_NEW_STATE_OFST 0 |
| #define MC_CMD_DRV_ATTACH_IN_UPDATE_OFST 4 |
| #define MC_CMD_DRV_ATTACH_OUT_LEN 4 |
| #define MC_CMD_DRV_ATTACH_OUT_OLD_STATE_OFST 0 |
| |
| /* MC_CMD_NCSI_PROD: (debug) |
| * Trigger an NC-SI event (and possibly an AEN in response) |
| */ |
| #define MC_CMD_NCSI_PROD 0x1d |
| #define MC_CMD_NCSI_PROD_IN_LEN 4 |
| #define MC_CMD_NCSI_PROD_IN_EVENTS_OFST 0 |
| #define MC_CMD_NCSI_PROD_LINKCHANGE_LBN 0 |
| #define MC_CMD_NCSI_PROD_LINKCHANGE_WIDTH 1 |
| #define MC_CMD_NCSI_PROD_RESET_LBN 1 |
| #define MC_CMD_NCSI_PROD_RESET_WIDTH 1 |
| #define MC_CMD_NCSI_PROD_DRVATTACH_LBN 2 |
| #define MC_CMD_NCSI_PROD_DRVATTACH_WIDTH 1 |
| #define MC_CMD_NCSI_PROD_OUT_LEN 0 |
| |
| /* Enumeration */ |
| #define MC_CMD_NCSI_PROD_LINKCHANGE 0 |
| #define MC_CMD_NCSI_PROD_RESET 1 |
| #define MC_CMD_NCSI_PROD_DRVATTACH 2 |
| |
| /* MC_CMD_DEVEL: (debug) |
| * Reserved for development |
| */ |
| #define MC_CMD_DEVEL 0x1e |
| |
| /* MC_CMD_SHMUART: (debug) |
| * Route UART output to circular buffer in shared memory instead. |
| */ |
| #define MC_CMD_SHMUART 0x1f |
| #define MC_CMD_SHMUART_IN_FLAG_OFST 0 |
| #define MC_CMD_SHMUART_IN_LEN 4 |
| #define MC_CMD_SHMUART_OUT_LEN 0 |
| |
| /* MC_CMD_PORT_RESET: |
| * Generic per-port reset. There is no equivalent for per-board reset. |
| * |
| * Locks required: None |
| * Return code: 0, ETIME |
| */ |
| #define MC_CMD_PORT_RESET 0x20 |
| #define MC_CMD_PORT_RESET_IN_LEN 0 |
| #define MC_CMD_PORT_RESET_OUT_LEN 0 |
| |
| /* MC_CMD_RESOURCE_LOCK: |
| * Generic resource lock/unlock interface. |
| * |
| * Locks required: None |
| * Return code: 0, |
| * EBUSY (if trylock is contended by other port), |
| * EDEADLK (if trylock is already acquired by this port) |
| * EINVAL (if unlock doesn't own the lock) |
| */ |
| #define MC_CMD_RESOURCE_LOCK 0x21 |
| #define MC_CMD_RESOURCE_LOCK_IN_LEN 8 |
| #define MC_CMD_RESOURCE_LOCK_IN_ACTION_OFST 0 |
| #define MC_CMD_RESOURCE_LOCK_ACTION_TRYLOCK 1 |
| #define MC_CMD_RESOURCE_LOCK_ACTION_UNLOCK 0 |
| #define MC_CMD_RESOURCE_LOCK_IN_RESOURCE_OFST 4 |
| #define MC_CMD_RESOURCE_LOCK_I2C 2 |
| #define MC_CMD_RESOURCE_LOCK_PHY 3 |
| #define MC_CMD_RESOURCE_LOCK_OUT_LEN 0 |
| |
| /* MC_CMD_SPI_COMMAND: (variadic in, variadic out) |
| * Read/Write to/from the SPI device. |
| * |
| * Locks required: SPI_LOCK |
| * Return code: 0, ETIME, EINVAL, EACCES (if SPI_LOCK is not held) |
| */ |
| #define MC_CMD_SPI_COMMAND 0x22 |
| #define MC_CMD_SPI_COMMAND_IN_LEN(_write_bytes) (12 + (_write_bytes)) |
| #define MC_CMD_SPI_COMMAND_IN_ARGS_OFST 0 |
| #define MC_CMD_SPI_COMMAND_IN_ARGS_ADDRESS_OFST 0 |
| #define MC_CMD_SPI_COMMAND_IN_ARGS_READ_BYTES_OFST 4 |
| #define MC_CMD_SPI_COMMAND_IN_ARGS_CHIP_SELECT_OFST 8 |
| /* Data to write here */ |
| #define MC_CMD_SPI_COMMAND_IN_WRITE_BUFFER_OFST 12 |
| #define MC_CMD_SPI_COMMAND_OUT_LEN(_read_bytes) (_read_bytes) |
| /* Data read here */ |
| #define MC_CMD_SPI_COMMAND_OUT_READ_BUFFER_OFST 0 |
| |
| /* MC_CMD_I2C_READ_WRITE: (variadic in, variadic out) |
| * Read/Write to/from the I2C bus. |
| * |
| * Locks required: I2C_LOCK |
| * Return code: 0, ETIME, EINVAL, EACCES (if I2C_LOCK is not held) |
| */ |
| #define MC_CMD_I2C_RW 0x23 |
| #define MC_CMD_I2C_RW_IN_LEN(_write_bytes) (8 + (_write_bytes)) |
| #define MC_CMD_I2C_RW_IN_ARGS_OFST 0 |
| #define MC_CMD_I2C_RW_IN_ARGS_ADDR_OFST 0 |
| #define MC_CMD_I2C_RW_IN_ARGS_READ_BYTES_OFST 4 |
| /* Data to write here */ |
| #define MC_CMD_I2C_RW_IN_WRITE_BUFFER_OFSET 8 |
| #define MC_CMD_I2C_RW_OUT_LEN(_read_bytes) (_read_bytes) |
| /* Data read here */ |
| #define MC_CMD_I2C_RW_OUT_READ_BUFFER_OFST 0 |
| |
| /* Generic phy capability bitmask */ |
| #define MC_CMD_PHY_CAP_10HDX_LBN 1 |
| #define MC_CMD_PHY_CAP_10HDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_10FDX_LBN 2 |
| #define MC_CMD_PHY_CAP_10FDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_100HDX_LBN 3 |
| #define MC_CMD_PHY_CAP_100HDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_100FDX_LBN 4 |
| #define MC_CMD_PHY_CAP_100FDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_1000HDX_LBN 5 |
| #define MC_CMD_PHY_CAP_1000HDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_1000FDX_LBN 6 |
| #define MC_CMD_PHY_CAP_1000FDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_10000FDX_LBN 7 |
| #define MC_CMD_PHY_CAP_10000FDX_WIDTH 1 |
| #define MC_CMD_PHY_CAP_PAUSE_LBN 8 |
| #define MC_CMD_PHY_CAP_PAUSE_WIDTH 1 |
| #define MC_CMD_PHY_CAP_ASYM_LBN 9 |
| #define MC_CMD_PHY_CAP_ASYM_WIDTH 1 |
| #define MC_CMD_PHY_CAP_AN_LBN 10 |
| #define MC_CMD_PHY_CAP_AN_WIDTH 1 |
| |
| /* Generic loopback enumeration */ |
| #define MC_CMD_LOOPBACK_NONE 0 |
| #define MC_CMD_LOOPBACK_DATA 1 |
| #define MC_CMD_LOOPBACK_GMAC 2 |
| #define MC_CMD_LOOPBACK_XGMII 3 |
| #define MC_CMD_LOOPBACK_XGXS 4 |
| #define MC_CMD_LOOPBACK_XAUI 5 |
| #define MC_CMD_LOOPBACK_GMII 6 |
| #define MC_CMD_LOOPBACK_SGMII 7 |
| #define MC_CMD_LOOPBACK_XGBR 8 |
| #define MC_CMD_LOOPBACK_XFI 9 |
| #define MC_CMD_LOOPBACK_XAUI_FAR 10 |
| #define MC_CMD_LOOPBACK_GMII_FAR 11 |
| #define MC_CMD_LOOPBACK_SGMII_FAR 12 |
| #define MC_CMD_LOOPBACK_XFI_FAR 13 |
| #define MC_CMD_LOOPBACK_GPHY 14 |
| #define MC_CMD_LOOPBACK_PHYXS 15 |
| #define MC_CMD_LOOPBACK_PCS 16 |
| #define MC_CMD_LOOPBACK_PMAPMD 17 |
| #define MC_CMD_LOOPBACK_XPORT 18 |
| #define MC_CMD_LOOPBACK_XGMII_WS 19 |
| #define MC_CMD_LOOPBACK_XAUI_WS 20 |
| #define MC_CMD_LOOPBACK_XAUI_WS_FAR 21 |
| #define MC_CMD_LOOPBACK_XAUI_WS_NEAR 22 |
| #define MC_CMD_LOOPBACK_GMII_WS 23 |
| #define MC_CMD_LOOPBACK_XFI_WS 24 |
| #define MC_CMD_LOOPBACK_XFI_WS_FAR 25 |
| #define MC_CMD_LOOPBACK_PHYXS_WS 26 |
| |
| /* Generic PHY statistics enumeration */ |
| #define MC_CMD_OUI 0 |
| #define MC_CMD_PMA_PMD_LINK_UP 1 |
| #define MC_CMD_PMA_PMD_RX_FAULT 2 |
| #define MC_CMD_PMA_PMD_TX_FAULT 3 |
| #define MC_CMD_PMA_PMD_SIGNAL 4 |
| #define MC_CMD_PMA_PMD_SNR_A 5 |
| #define MC_CMD_PMA_PMD_SNR_B 6 |
| #define MC_CMD_PMA_PMD_SNR_C 7 |
| #define MC_CMD_PMA_PMD_SNR_D 8 |
| #define MC_CMD_PCS_LINK_UP 9 |
| #define MC_CMD_PCS_RX_FAULT 10 |
| #define MC_CMD_PCS_TX_FAULT 11 |
| #define MC_CMD_PCS_BER 12 |
| #define MC_CMD_PCS_BLOCK_ERRORS 13 |
| #define MC_CMD_PHYXS_LINK_UP 14 |
| #define MC_CMD_PHYXS_RX_FAULT 15 |
| #define MC_CMD_PHYXS_TX_FAULT 16 |
| #define MC_CMD_PHYXS_ALIGN 17 |
| #define MC_CMD_PHYXS_SYNC 18 |
| #define MC_CMD_AN_LINK_UP 19 |
| #define MC_CMD_AN_COMPLETE 20 |
| #define MC_CMD_AN_10GBT_STATUS 21 |
| #define MC_CMD_CL22_LINK_UP 22 |
| #define MC_CMD_PHY_NSTATS 23 |
| |
| /* MC_CMD_GET_PHY_CFG: |
| * Report PHY configuration. This guarantees to succeed even if the PHY is in |
| * a "zombie" state. |
| * |
| * Locks required: None |
| * Return code: 0 |
| */ |
| #define MC_CMD_GET_PHY_CFG 0x24 |
| |
| #define MC_CMD_GET_PHY_CFG_IN_LEN 0 |
| #define MC_CMD_GET_PHY_CFG_OUT_LEN 72 |
| |
| #define MC_CMD_GET_PHY_CFG_OUT_FLAGS_OFST 0 |
| #define MC_CMD_GET_PHY_CFG_PRESENT_LBN 0 |
| #define MC_CMD_GET_PHY_CFG_PRESENT_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_LBN 1 |
| #define MC_CMD_GET_PHY_CFG_BIST_CABLE_SHORT_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_LBN 2 |
| #define MC_CMD_GET_PHY_CFG_BIST_CABLE_LONG_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_LOWPOWER_LBN 3 |
| #define MC_CMD_GET_PHY_CFG_LOWPOWER_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_POWEROFF_LBN 4 |
| #define MC_CMD_GET_PHY_CFG_POWEROFF_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_TXDIS_LBN 5 |
| #define MC_CMD_GET_PHY_CFG_TXDIS_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_BIST_LBN 6 |
| #define MC_CMD_GET_PHY_CFG_BIST_WIDTH 1 |
| #define MC_CMD_GET_PHY_CFG_OUT_TYPE_OFST 4 |
| /* Bitmask of supported capabilities */ |
| #define MC_CMD_GET_PHY_CFG_OUT_SUPPORTED_CAP_OFST 8 |
| #define MC_CMD_GET_PHY_CFG_OUT_CHANNEL_OFST 12 |
| #define MC_CMD_GET_PHY_CFG_OUT_PRT_OFST 16 |
| /* PHY statistics bitmap */ |
| #define MC_CMD_GET_PHY_CFG_OUT_STATS_MASK_OFST 20 |
| /* PHY type/name string */ |
| #define MC_CMD_GET_PHY_CFG_OUT_NAME_OFST 24 |
| #define MC_CMD_GET_PHY_CFG_OUT_NAME_LEN 20 |
| #define MC_CMD_GET_PHY_CFG_OUT_MEDIA_TYPE_OFST 44 |
| #define MC_CMD_MEDIA_XAUI 1 |
| #define MC_CMD_MEDIA_CX4 2 |
| #define MC_CMD_MEDIA_KX4 3 |
| #define MC_CMD_MEDIA_XFP 4 |
| #define MC_CMD_MEDIA_SFP_PLUS 5 |
| #define MC_CMD_MEDIA_BASE_T 6 |
| /* MDIO "MMDS" supported */ |
| #define MC_CMD_GET_PHY_CFG_OUT_MMD_MASK_OFST 48 |
| /* Native clause 22 */ |
| #define MC_CMD_MMD_CLAUSE22 0 |
| #define MC_CMD_MMD_CLAUSE45_PMAPMD 1 |
| #define MC_CMD_MMD_CLAUSE45_WIS 2 |
| #define MC_CMD_MMD_CLAUSE45_PCS 3 |
| #define MC_CMD_MMD_CLAUSE45_PHYXS 4 |
| #define MC_CMD_MMD_CLAUSE45_DTEXS 5 |
| #define MC_CMD_MMD_CLAUSE45_TC 6 |
| #define MC_CMD_MMD_CLAUSE45_AN 7 |
| /* Clause22 proxied over clause45 by PHY */ |
| #define MC_CMD_MMD_CLAUSE45_C22EXT 29 |
| #define MC_CMD_MMD_CLAUSE45_VEND1 30 |
| #define MC_CMD_MMD_CLAUSE45_VEND2 31 |
| /* PHY stepping version */ |
| #define MC_CMD_GET_PHY_CFG_OUT_REVISION_OFST 52 |
| #define MC_CMD_GET_PHY_CFG_OUT_REVISION_LEN 20 |
| |
| /* MC_CMD_START_BIST: |
| * Start a BIST test on the PHY. |
| * |
| * Locks required: PHY_LOCK if doing a PHY BIST |
| * Return code: 0, EINVAL, EACCES (if PHY_LOCK is not held) |
| */ |
| #define MC_CMD_START_BIST 0x25 |
| #define MC_CMD_START_BIST_IN_LEN 4 |
| #define MC_CMD_START_BIST_IN_TYPE_OFST 0 |
| #define MC_CMD_START_BIST_OUT_LEN 0 |
| |
| /* Run the PHY's short cable BIST */ |
| #define MC_CMD_PHY_BIST_CABLE_SHORT 1 |
| /* Run the PHY's long cable BIST */ |
| #define MC_CMD_PHY_BIST_CABLE_LONG 2 |
| /* Run BIST on the currently selected BPX Serdes (XAUI or XFI) */ |
| #define MC_CMD_BPX_SERDES_BIST 3 |
| /* Run the MC loopback tests */ |
| #define MC_CMD_MC_LOOPBACK_BIST 4 |
| /* Run the PHY's standard BIST */ |
| #define MC_CMD_PHY_BIST 5 |
| |
| /* MC_CMD_POLL_PHY_BIST: (variadic output) |
| * Poll for BIST completion |
| * |
| * Returns a single status code, and optionally some PHY specific |
| * bist output. The driver should only consume the BIST output |
| * after validating OUTLEN and PHY_CFG.PHY_TYPE. |
| * |
| * If a driver can't successfully parse the BIST output, it should |
| * still respect the pass/Fail in OUT.RESULT |
| * |
| * Locks required: PHY_LOCK if doing a PHY BIST |
| * Return code: 0, EACCES (if PHY_LOCK is not held) |
| */ |
| #define MC_CMD_POLL_BIST 0x26 |
| #define MC_CMD_POLL_BIST_IN_LEN 0 |
| #define MC_CMD_POLL_BIST_OUT_LEN UNKNOWN |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_LEN 36 |
| #define MC_CMD_POLL_BIST_OUT_MRSFP_LEN 8 |
| #define MC_CMD_POLL_BIST_OUT_RESULT_OFST 0 |
| #define MC_CMD_POLL_BIST_RUNNING 1 |
| #define MC_CMD_POLL_BIST_PASSED 2 |
| #define MC_CMD_POLL_BIST_FAILED 3 |
| #define MC_CMD_POLL_BIST_TIMEOUT 4 |
| /* Generic: */ |
| #define MC_CMD_POLL_BIST_OUT_PRIVATE_OFST 4 |
| /* SFT9001-specific: */ |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_A_OFST 4 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_B_OFST 8 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_C_OFST 12 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_LENGTH_D_OFST 16 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_A_OFST 20 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_B_OFST 24 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_C_OFST 28 |
| #define MC_CMD_POLL_BIST_OUT_SFT9001_CABLE_STATUS_D_OFST 32 |
| #define MC_CMD_POLL_BIST_SFT9001_PAIR_OK 1 |
| #define MC_CMD_POLL_BIST_SFT9001_PAIR_OPEN 2 |
| #define MC_CMD_POLL_BIST_SFT9001_INTRA_PAIR_SHORT 3 |
| #define MC_CMD_POLL_BIST_SFT9001_INTER_PAIR_SHORT 4 |
| #define MC_CMD_POLL_BIST_SFT9001_PAIR_BUSY 9 |
| /* mrsfp "PHY" driver: */ |
| #define MC_CMD_POLL_BIST_OUT_MRSFP_TEST_OFST 4 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_COMPLETE 0 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_WRITE 1 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_IO_EXP 2 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_OFF_I2C_NO_ACCESS_MODULE 3 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_IO_EXP_I2C_CONFIGURE 4 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_BUS_SWITCH_I2C_NO_CROSSTALK 5 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_PRESENCE 6 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_I2C_ACCESS 7 |
| #define MC_CMD_POLL_BIST_MRSFP_TEST_MODULE_ID_SANE_VALUE 8 |
| |
| /* MC_CMD_PHY_SPI: (variadic in, variadic out) |
| * Read/Write/Erase the PHY SPI device |
| * |
| * Locks required: PHY_LOCK |
| * Return code: 0, ETIME, EINVAL, EACCES (if PHY_LOCK is not held) |
| */ |
| #define MC_CMD_PHY_SPI 0x27 |
| #define MC_CMD_PHY_SPI_IN_LEN(_write_bytes) (12 + (_write_bytes)) |
| #define MC_CMD_PHY_SPI_IN_ARGS_OFST 0 |
| #define MC_CMD_PHY_SPI_IN_ARGS_ADDR_OFST 0 |
| #define MC_CMD_PHY_SPI_IN_ARGS_READ_BYTES_OFST 4 |
| #define MC_CMD_PHY_SPI_IN_ARGS_ERASE_ALL_OFST 8 |
| /* Data to write here */ |
| #define MC_CMD_PHY_SPI_IN_WRITE_BUFFER_OFSET 12 |
| #define MC_CMD_PHY_SPI_OUT_LEN(_read_bytes) (_read_bytes) |
| /* Data read here */ |
| #define MC_CMD_PHY_SPI_OUT_READ_BUFFER_OFST 0 |
| |
| |
| /* MC_CMD_GET_LOOPBACK_MODES: |
| * Returns a bitmask of loopback modes evailable at each speed. |
| * |
| * Locks required: None |
| * Return code: 0 |
| */ |
| #define MC_CMD_GET_LOOPBACK_MODES 0x28 |
| #define MC_CMD_GET_LOOPBACK_MODES_IN_LEN 0 |
| #define MC_CMD_GET_LOOPBACK_MODES_OUT_LEN 32 |
| #define MC_CMD_GET_LOOPBACK_MODES_100M_OFST 0 |
| #define MC_CMD_GET_LOOPBACK_MODES_1G_OFST 8 |
| #define MC_CMD_GET_LOOPBACK_MODES_10G_OFST 16 |
| #define MC_CMD_GET_LOOPBACK_MODES_SUGGESTED_OFST 24 |
| |
| /* Flow control enumeration */ |
| #define MC_CMD_FCNTL_OFF 0 |
| #define MC_CMD_FCNTL_RESPOND 1 |
| #define MC_CMD_FCNTL_BIDIR 2 |
| /* Auto - Use what the link has autonegotiated |
| * - The driver should modify the advertised capabilities via SET_LINK.CAP |
| * to control the negotiated flow control mode. |
| * - Can only be set if the PHY supports PAUSE+ASYM capabilities |
| * - Never returned by GET_LINK as the value programmed into the MAC |
| */ |
| #define MC_CMD_FCNTL_AUTO 3 |
| |
| /* Generic mac fault bitmask */ |
| #define MC_CMD_MAC_FAULT_XGMII_LOCAL_LBN 0 |
| #define MC_CMD_MAC_FAULT_XGMII_LOCAL_WIDTH 1 |
| #define MC_CMD_MAC_FAULT_XGMII_REMOTE_LBN 1 |
| #define MC_CMD_MAC_FAULT_XGMII_REMOTE_WIDTH 1 |
| #define MC_CMD_MAC_FAULT_SGMII_REMOTE_LBN 2 |
| #define MC_CMD_MAC_FAULT_SGMII_REMOTE_WIDTH 1 |
| |
| /* MC_CMD_GET_LINK: |
| * Read the unified MAC/PHY link state |
| * |
| * Locks required: None |
| * Return code: 0, ETIME |
| */ |
| #define MC_CMD_GET_LINK 0x29 |
| #define MC_CMD_GET_LINK_IN_LEN 0 |
| #define MC_CMD_GET_LINK_OUT_LEN 28 |
| /* near-side and link-partner advertised capabilities */ |
| #define MC_CMD_GET_LINK_OUT_CAP_OFST 0 |
| #define MC_CMD_GET_LINK_OUT_LP_CAP_OFST 4 |
| /* Autonegotiated speed in mbit/s. The link may still be down |
| * even if this reads non-zero */ |
| #define MC_CMD_GET_LINK_OUT_LINK_SPEED_OFST 8 |
| #define MC_CMD_GET_LINK_OUT_LOOPBACK_MODE_OFST 12 |
| #define MC_CMD_GET_LINK_OUT_FLAGS_OFST 16 |
| /* Whether we have overall link up */ |
| #define MC_CMD_GET_LINK_LINK_UP_LBN 0 |
| #define MC_CMD_GET_LINK_LINK_UP_WIDTH 1 |
| #define MC_CMD_GET_LINK_FULL_DUPLEX_LBN 1 |
| #define MC_CMD_GET_LINK_FULL_DUPLEX_WIDTH 1 |
| /* Whether we have link at the layers provided by the BPX */ |
| #define MC_CMD_GET_LINK_BPX_LINK_LBN 2 |
| #define MC_CMD_GET_LINK_BPX_LINK_WIDTH 1 |
| /* Whether the PHY has external link */ |
| #define MC_CMD_GET_LINK_PHY_LINK_LBN 3 |
| #define MC_CMD_GET_LINK_PHY_LINK_WIDTH 1 |
| #define MC_CMD_GET_LINK_OUT_FCNTL_OFST 20 |
| #define MC_CMD_GET_LINK_OUT_MAC_FAULT_OFST 24 |
| |
| /* MC_CMD_SET_LINK: |
| * Write the unified MAC/PHY link configuration |
| * |
| * A loopback speed of "0" is supported, and means |
| * (choose any available speed) |
| * |
| * Locks required: None |
| * Return code: 0, EINVAL, ETIME |
| */ |
| #define MC_CMD_SET_LINK 0x2a |
| #define MC_CMD_SET_LINK_IN_LEN 16 |
| #define MC_CMD_SET_LINK_IN_CAP_OFST 0 |
| #define MC_CMD_SET_LINK_IN_FLAGS_OFST 4 |
| #define MC_CMD_SET_LINK_LOWPOWER_LBN 0 |
| #define MC_CMD_SET_LINK_LOWPOWER_WIDTH 1 |
| #define MC_CMD_SET_LINK_POWEROFF_LBN 1 |
| #define MC_CMD_SET_LINK_POWEROFF_WIDTH 1 |
| #define MC_CMD_SET_LINK_TXDIS_LBN 2 |
| #define MC_CMD_SET_LINK_TXDIS_WIDTH 1 |
| #define MC_CMD_SET_LINK_IN_LOOPBACK_MODE_OFST 8 |
| #define MC_CMD_SET_LINK_IN_LOOPBACK_SPEED_OFST 12 |
| #define MC_CMD_SET_LINK_OUT_LEN 0 |
| |
| /* MC_CMD_SET_ID_LED: |
| * Set indentification LED state |
| * |
| * Locks required: None |
| * Return code: 0, EINVAL |
| */ |
| #define MC_CMD_SET_ID_LED 0x2b |
| #define MC_CMD_SET_ID_LED_IN_LEN 4 |
| #define MC_CMD_SET_ID_LED_IN_STATE_OFST 0 |
| #define MC_CMD_LED_OFF 0 |
| #define MC_CMD_LED_ON 1 |
| #define MC_CMD_LED_DEFAULT 2 |
| #define MC_CMD_SET_ID_LED_OUT_LEN 0 |
| |
| /* MC_CMD_SET_MAC: |
| * Set MAC configuration |
| * |
| * The MTU is the MTU programmed directly into the XMAC/GMAC |
| * (inclusive of EtherII, VLAN, bug16011 padding) |
| * |
| * Locks required: None |
| * Return code: 0, EINVAL |
| */ |
| #define MC_CMD_SET_MAC 0x2c |
| #define MC_CMD_SET_MAC_IN_LEN 24 |
| #define MC_CMD_SET_MAC_IN_MTU_OFST 0 |
| #define MC_CMD_SET_MAC_IN_DRAIN_OFST 4 |
| #define MC_CMD_SET_MAC_IN_ADDR_OFST 8 |
| #define MC_CMD_SET_MAC_IN_REJECT_OFST 16 |
| #define MC_CMD_SET_MAC_IN_REJECT_UNCST_LBN 0 |
| #define MC_CMD_SET_MAC_IN_REJECT_UNCST_WIDTH 1 |
| #define MC_CMD_SET_MAC_IN_REJECT_BRDCST_LBN 1 |
| #define MC_CMD_SET_MAC_IN_REJECT_BRDCST_WIDTH 1 |
| #define MC_CMD_SET_MAC_IN_FCNTL_OFST 20 |
| #define MC_CMD_SET_MAC_OUT_LEN 0 |
| |
| /* MC_CMD_PHY_STATS: |
| * Get generic PHY statistics |
| * |
| * This call returns the statistics for a generic PHY in a sparse |
| * array (indexed by the enumerate). Each value is represented by |
| * a 32bit number. |
| * |
| * If the DMA_ADDR is 0, then no DMA is performed, and the statistics |
| * may be read directly out of shared memory. If DMA_ADDR != 0, then |
| * the statistics are dmad to that (page-aligned location) |
| * |
| * Locks required: None |
| * Returns: 0, ETIME |
| * Response methods: shared memory, event |
| */ |
| #define MC_CMD_PHY_STATS 0x2d |
| #define MC_CMD_PHY_STATS_IN_LEN 8 |
| #define MC_CMD_PHY_STATS_IN_DMA_ADDR_LO_OFST 0 |
| #define MC_CMD_PHY_STATS_IN_DMA_ADDR_HI_OFST 4 |
| #define MC_CMD_PHY_STATS_OUT_DMA_LEN 0 |
| #define MC_CMD_PHY_STATS_OUT_NO_DMA_LEN (MC_CMD_PHY_NSTATS * 4) |
| |
| /* Unified MAC statistics enumeration */ |
| #define MC_CMD_MAC_GENERATION_START 0 |
| #define MC_CMD_MAC_TX_PKTS 1 |
| #define MC_CMD_MAC_TX_PAUSE_PKTS 2 |
| #define MC_CMD_MAC_TX_CONTROL_PKTS 3 |
| #define MC_CMD_MAC_TX_UNICAST_PKTS 4 |
| #define MC_CMD_MAC_TX_MULTICAST_PKTS 5 |
| #define MC_CMD_MAC_TX_BROADCAST_PKTS 6 |
| #define MC_CMD_MAC_TX_BYTES 7 |
| #define MC_CMD_MAC_TX_BAD_BYTES 8 |
| #define MC_CMD_MAC_TX_LT64_PKTS 9 |
| #define MC_CMD_MAC_TX_64_PKTS 10 |
| #define MC_CMD_MAC_TX_65_TO_127_PKTS 11 |
| #define MC_CMD_MAC_TX_128_TO_255_PKTS 12 |
| #define MC_CMD_MAC_TX_256_TO_511_PKTS 13 |
| #define MC_CMD_MAC_TX_512_TO_1023_PKTS 14 |
| #define MC_CMD_MAC_TX_1024_TO_15XX_PKTS 15 |
| #define MC_CMD_MAC_TX_15XX_TO_JUMBO_PKTS 16 |
| #define MC_CMD_MAC_TX_GTJUMBO_PKTS 17 |
| #define MC_CMD_MAC_TX_BAD_FCS_PKTS 18 |
| #define MC_CMD_MAC_TX_SINGLE_COLLISION_PKTS 19 |
| #define MC_CMD_MAC_TX_MULTIPLE_COLLISION_PKTS 20 |
| #define MC_CMD_MAC_TX_EXCESSIVE_COLLISION_PKTS 21 |
| #define MC_CMD_MAC_TX_LATE_COLLISION_PKTS 22 |
| #define MC_CMD_MAC_TX_DEFERRED_PKTS 23 |
| #define MC_CMD_MAC_TX_EXCESSIVE_DEFERRED_PKTS 24 |
| #define MC_CMD_MAC_TX_NON_TCPUDP_PKTS 25 |
| #define MC_CMD_MAC_TX_MAC_SRC_ERR_PKTS 26 |
| #define MC_CMD_MAC_TX_IP_SRC_ERR_PKTS 27 |
| #define MC_CMD_MAC_RX_PKTS 28 |
| #define MC_CMD_MAC_RX_PAUSE_PKTS 29 |
| #define MC_CMD_MAC_RX_GOOD_PKTS 30 |
| #define MC_CMD_MAC_RX_CONTROL_PKTS 31 |
| #define MC_CMD_MAC_RX_UNICAST_PKTS 32 |
| #define MC_CMD_MAC_RX_MULTICAST_PKTS 33 |
| #define MC_CMD_MAC_RX_BROADCAST_PKTS 34 |
| #define MC_CMD_MAC_RX_BYTES 35 |
| #define MC_CMD_MAC_RX_BAD_BYTES 36 |
| #define MC_CMD_MAC_RX_64_PKTS 37 |
| #define MC_CMD_MAC_RX_65_TO_127_PKTS 38 |
| #define MC_CMD_MAC_RX_128_TO_255_PKTS 39 |
| #define MC_CMD_MAC_RX_256_TO_511_PKTS 40 |
| #define MC_CMD_MAC_RX_512_TO_1023_PKTS 41 |
| #define MC_CMD_MAC_RX_1024_TO_15XX_PKTS 42 |
| #define MC_CMD_MAC_RX_15XX_TO_JUMBO_PKTS 43 |
| #define MC_CMD_MAC_RX_GTJUMBO_PKTS 44 |
| #define MC_CMD_MAC_RX_UNDERSIZE_PKTS 45 |
| #define MC_CMD_MAC_RX_BAD_FCS_PKTS 46 |
| #define MC_CMD_MAC_RX_OVERFLOW_PKTS 47 |
| #define MC_CMD_MAC_RX_FALSE_CARRIER_PKTS 48 |
| #define MC_CMD_MAC_RX_SYMBOL_ERROR_PKTS 49 |
| #define MC_CMD_MAC_RX_ALIGN_ERROR_PKTS 50 |
| #define MC_CMD_MAC_RX_LENGTH_ERROR_PKTS 51 |
| #define MC_CMD_MAC_RX_INTERNAL_ERROR_PKTS 52 |
| #define MC_CMD_MAC_RX_JABBER_PKTS 53 |
| #define MC_CMD_MAC_RX_NODESC_DROPS 54 |
| #define MC_CMD_MAC_RX_LANES01_CHAR_ERR 55 |
| #define MC_CMD_MAC_RX_LANES23_CHAR_ERR 56 |
| #define MC_CMD_MAC_RX_LANES01_DISP_ERR 57 |
| #define MC_CMD_MAC_RX_LANES23_DISP_ERR 58 |
| #define MC_CMD_MAC_RX_MATCH_FAULT 59 |
| #define MC_CMD_GMAC_DMABUF_START 64 |
| #define MC_CMD_GMAC_DMABUF_END 95 |
| /* Insert new members here. */ |
| #define MC_CMD_MAC_GENERATION_END 96 |
| #define MC_CMD_MAC_NSTATS (MC_CMD_MAC_GENERATION_END+1) |
| |
| /* MC_CMD_MAC_STATS: |
| * Get unified GMAC/XMAC statistics |
| * |
| * This call returns unified statistics maintained by the MC as it |
| * switches between the GMAC and XMAC. The MC will write out all |
| * supported stats. The driver should zero initialise the buffer to |
| * guarantee consistent results. |
| * |
| * Locks required: None |
| * Returns: 0 |
| * Response methods: shared memory, event |
| */ |
| #define MC_CMD_MAC_STATS 0x2e |
| #define MC_CMD_MAC_STATS_IN_LEN 16 |
| #define MC_CMD_MAC_STATS_IN_DMA_ADDR_LO_OFST 0 |
| #define MC_CMD_MAC_STATS_IN_DMA_ADDR_HI_OFST 4 |
| #define MC_CMD_MAC_STATS_IN_CMD_OFST 8 |
| #define MC_CMD_MAC_STATS_CMD_DMA_LBN 0 |
| #define MC_CMD_MAC_STATS_CMD_DMA_WIDTH 1 |
| #define MC_CMD_MAC_STATS_CMD_CLEAR_LBN 1 |
| #define MC_CMD_MAC_STATS_CMD_CLEAR_WIDTH 1 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_LBN 2 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_CHANGE_WIDTH 1 |
| /* Remaining PERIOD* fields only relevent when PERIODIC_CHANGE is set */ |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_LBN 3 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_ENABLE_WIDTH 1 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_LBN 4 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_CLEAR_WIDTH 1 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_LBN 5 |
| #define MC_CMD_MAC_STATS_CMD_PERIODIC_NOEVENT_WIDTH 1 |
| #define MC_CMD_MAC_STATS_CMD_PERIOD_MS_LBN 16 |
| #define MC_CMD_MAC_STATS_CMD_PERIOD_MS_WIDTH 16 |
| #define MC_CMD_MAC_STATS_IN_DMA_LEN_OFST 12 |
| |
| #define MC_CMD_MAC_STATS_OUT_LEN 0 |
| |
| /* Callisto flags */ |
| #define MC_CMD_SFT9001_ROBUST_LBN 0 |
| #define MC_CMD_SFT9001_ROBUST_WIDTH 1 |
| #define MC_CMD_SFT9001_SHORT_REACH_LBN 1 |
| #define MC_CMD_SFT9001_SHORT_REACH_WIDTH 1 |
| |
| /* MC_CMD_SFT9001_GET: |
| * Read current callisto specific setting |
| * |
| * Locks required: None |
| * Returns: 0, ETIME |
| */ |
| #define MC_CMD_SFT9001_GET 0x30 |
| #define MC_CMD_SFT9001_GET_IN_LEN 0 |
| #define MC_CMD_SFT9001_GET_OUT_LEN 4 |
| #define MC_CMD_SFT9001_GET_OUT_FLAGS_OFST 0 |
| |
| /* MC_CMD_SFT9001_SET: |
| * Write current callisto specific setting |
| * |
| * Locks required: None |
| * Returns: 0, ETIME, EINVAL |
| */ |
| #define MC_CMD_SFT9001_SET 0x31 |
| #define MC_CMD_SFT9001_SET_IN_LEN 4 |
| #define MC_CMD_SFT9001_SET_IN_FLAGS_OFST 0 |
| #define MC_CMD_SFT9001_SET_OUT_LEN 0 |
| |
| |
| /* MC_CMD_WOL_FILTER_SET: |
| * Set a WoL filter |
| * |
| * Locks required: None |
| * Returns: 0, EBUSY, EINVAL, ENOSYS |
| */ |
| #define MC_CMD_WOL_FILTER_SET 0x32 |
| #define MC_CMD_WOL_FILTER_SET_IN_LEN 192 /* 190 rounded up to a word */ |
| #define MC_CMD_WOL_FILTER_SET_IN_FILTER_MODE_OFST 0 |
| #define MC_CMD_WOL_FILTER_SET_IN_WOL_TYPE_OFST 4 |
| |
| /* There is a union at offset 8, following defines overlap due to |
| * this */ |
| #define MC_CMD_WOL_FILTER_SET_IN_DATA_OFST 8 |
| |
| #define MC_CMD_WOL_FILTER_SET_IN_MAGIC_MAC_OFST \ |
| MC_CMD_WOL_FILTER_SET_IN_DATA_OFST |
| |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_IP_OFST \ |
| MC_CMD_WOL_FILTER_SET_IN_DATA_OFST |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_IP_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 4) |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_SRC_PORT_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 8) |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV4_SYN_DST_PORT_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 10) |
| |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_IP_OFST \ |
| MC_CMD_WOL_FILTER_SET_IN_DATA_OFST |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_IP_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 16) |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_SRC_PORT_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 32) |
| #define MC_CMD_WOL_FILTER_SET_IN_IPV6_SYN_DST_PORT_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 34) |
| |
| #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_MASK_OFST \ |
| MC_CMD_WOL_FILTER_SET_IN_DATA_OFST |
| #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 48) |
| #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LEN_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 176) |
| #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER3_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 177) |
| #define MC_CMD_WOL_FILTER_SET_IN_BITMAP_LAYER4_OFST \ |
| (MC_CMD_WOL_FILTER_SET_IN_DATA_OFST + 178) |
| |
| #define MC_CMD_WOL_FILTER_SET_IN_LINK_MASK_OFST \ |
| MC_CMD_WOL_FILTER_SET_IN_DATA_OFST |
| #define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_LBN 0 |
| #define MC_CMD_WOL_FILTER_SET_IN_LINK_UP_WIDTH 1 |
| #define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_LBN 1 |
| #define MC_CMD_WOL_FILTER_SET_IN_LINK_DOWN_WIDTH 1 |
| |
| #define MC_CMD_WOL_FILTER_SET_OUT_LEN 4 |
| #define MC_CMD_WOL_FILTER_SET_OUT_FILTER_ID_OFST 0 |
| |
| /* WOL Filter types enumeration */ |
| #define MC_CMD_WOL_TYPE_MAGIC 0x0 |
| /* unused 0x1 */ |
| #define MC_CMD_WOL_TYPE_WIN_MAGIC 0x2 |
| #define MC_CMD_WOL_TYPE_IPV4_SYN 0x3 |
| #define MC_CMD_WOL_TYPE_IPV6_SYN 0x4 |
| #define MC_CMD_WOL_TYPE_BITMAP 0x5 |
| #define MC_CMD_WOL_TYPE_LINK 0x6 |
| #define MC_CMD_WOL_TYPE_MAX 0x7 |
| |
| #define MC_CMD_FILTER_MODE_SIMPLE 0x0 |
| #define MC_CMD_FILTER_MODE_STRUCTURED 0xffffffff |
| |
| /* MC_CMD_WOL_FILTER_REMOVE: |
| * Remove a WoL filter |
| * |
| * Locks required: None |
| * Returns: 0, EINVAL, ENOSYS |
| */ |
| #define MC_CMD_WOL_FILTER_REMOVE 0x33 |
| #define MC_CMD_WOL_FILTER_REMOVE_IN_LEN 4 |
| #define MC_CMD_WOL_FILTER_REMOVE_IN_FILTER_ID_OFST 0 |
| #define MC_CMD_WOL_FILTER_REMOVE_OUT_LEN 0 |
| |
| |
| /* MC_CMD_WOL_FILTER_RESET: |
| * Reset (i.e. remove all) WoL filters |
| * |
| * Locks required: None |
| * Returns: 0, ENOSYS |
| */ |
| #define MC_CMD_WOL_FILTER_RESET 0x34 |
| #define MC_CMD_WOL_FILTER_RESET_IN_LEN 0 |
| #define MC_CMD_WOL_FILTER_RESET_OUT_LEN 0 |
| |
| /* MC_CMD_SET_MCAST_HASH: |
| * Set the MCASH hash value without otherwise |
| * reconfiguring the MAC |
| */ |
| #define MC_CMD_SET_MCAST_HASH 0x35 |
| #define MC_CMD_SET_MCAST_HASH_IN_LEN 32 |
| #define MC_CMD_SET_MCAST_HASH_IN_HASH0_OFST 0 |
| #define MC_CMD_SET_MCAST_HASH_IN_HASH1_OFST 16 |
| #define MC_CMD_SET_MCAST_HASH_OUT_LEN 0 |
| |
| /* MC_CMD_NVRAM_TYPES: |
| * Return bitfield indicating available types of virtual NVRAM partitions |
| * |
| * Locks required: none |
| * Returns: 0 |
| */ |
| #define MC_CMD_NVRAM_TYPES 0x36 |
| #define MC_CMD_NVRAM_TYPES_IN_LEN 0 |
| #define MC_CMD_NVRAM_TYPES_OUT_LEN 4 |
| #define MC_CMD_NVRAM_TYPES_OUT_TYPES_OFST 0 |
| |
| /* Supported NVRAM types */ |
| #define MC_CMD_NVRAM_TYPE_DISABLED_CALLISTO 0 |
| #define MC_CMD_NVRAM_TYPE_MC_FW 1 |
| #define MC_CMD_NVRAM_TYPE_MC_FW_BACKUP 2 |
| #define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT0 3 |
| #define MC_CMD_NVRAM_TYPE_STATIC_CFG_PORT1 4 |
| #define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT0 5 |
| #define MC_CMD_NVRAM_TYPE_DYNAMIC_CFG_PORT1 6 |
| #define MC_CMD_NVRAM_TYPE_EXP_ROM 7 |
| #define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT0 8 |
| #define MC_CMD_NVRAM_TYPE_EXP_ROM_CFG_PORT1 9 |
| #define MC_CMD_NVRAM_TYPE_PHY_PORT0 10 |
| #define MC_CMD_NVRAM_TYPE_PHY_PORT1 11 |
| #define MC_CMD_NVRAM_TYPE_LOG 12 |
| |
| /* MC_CMD_NVRAM_INFO: |
| * Read info about a virtual NVRAM partition |
| * |
| * Locks required: none |
| * Returns: 0, EINVAL (bad type) |
| */ |
| #define MC_CMD_NVRAM_INFO 0x37 |
| #define MC_CMD_NVRAM_INFO_IN_LEN 4 |
| #define MC_CMD_NVRAM_INFO_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_INFO_OUT_LEN 24 |
| #define MC_CMD_NVRAM_INFO_OUT_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_INFO_OUT_SIZE_OFST 4 |
| #define MC_CMD_NVRAM_INFO_OUT_ERASESIZE_OFST 8 |
| #define MC_CMD_NVRAM_INFO_OUT_FLAGS_OFST 12 |
| #define MC_CMD_NVRAM_PROTECTED_LBN 0 |
| #define MC_CMD_NVRAM_PROTECTED_WIDTH 1 |
| #define MC_CMD_NVRAM_INFO_OUT_PHYSDEV_OFST 16 |
| #define MC_CMD_NVRAM_INFO_OUT_PHYSADDR_OFST 20 |
| |
| /* MC_CMD_NVRAM_UPDATE_START: |
| * Start a group of update operations on a virtual NVRAM partition |
| * |
| * Locks required: PHY_LOCK if type==*PHY* |
| * Returns: 0, EINVAL (bad type), EACCES (if PHY_LOCK required and not held) |
| */ |
| #define MC_CMD_NVRAM_UPDATE_START 0x38 |
| #define MC_CMD_NVRAM_UPDATE_START_IN_LEN 4 |
| #define MC_CMD_NVRAM_UPDATE_START_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_UPDATE_START_OUT_LEN 0 |
| |
| /* MC_CMD_NVRAM_READ: |
| * Read data from a virtual NVRAM partition |
| * |
| * Locks required: PHY_LOCK if type==*PHY* |
| * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held) |
| */ |
| #define MC_CMD_NVRAM_READ 0x39 |
| #define MC_CMD_NVRAM_READ_IN_LEN 12 |
| #define MC_CMD_NVRAM_READ_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_READ_IN_OFFSET_OFST 4 |
| #define MC_CMD_NVRAM_READ_IN_LENGTH_OFST 8 |
| #define MC_CMD_NVRAM_READ_OUT_LEN(_read_bytes) (_read_bytes) |
| #define MC_CMD_NVRAM_READ_OUT_READ_BUFFER_OFST 0 |
| |
| /* MC_CMD_NVRAM_WRITE: |
| * Write data to a virtual NVRAM partition |
| * |
| * Locks required: PHY_LOCK if type==*PHY* |
| * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held) |
| */ |
| #define MC_CMD_NVRAM_WRITE 0x3a |
| #define MC_CMD_NVRAM_WRITE_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_WRITE_IN_OFFSET_OFST 4 |
| #define MC_CMD_NVRAM_WRITE_IN_LENGTH_OFST 8 |
| #define MC_CMD_NVRAM_WRITE_IN_WRITE_BUFFER_OFST 12 |
| #define MC_CMD_NVRAM_WRITE_IN_LEN(_write_bytes) (12 + _write_bytes) |
| #define MC_CMD_NVRAM_WRITE_OUT_LEN 0 |
| |
| /* MC_CMD_NVRAM_ERASE: |
| * Erase sector(s) from a virtual NVRAM partition |
| * |
| * Locks required: PHY_LOCK if type==*PHY* |
| * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held) |
| */ |
| #define MC_CMD_NVRAM_ERASE 0x3b |
| #define MC_CMD_NVRAM_ERASE_IN_LEN 12 |
| #define MC_CMD_NVRAM_ERASE_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_ERASE_IN_OFFSET_OFST 4 |
| #define MC_CMD_NVRAM_ERASE_IN_LENGTH_OFST 8 |
| #define MC_CMD_NVRAM_ERASE_OUT_LEN 0 |
| |
| /* MC_CMD_NVRAM_UPDATE_FINISH: |
| * Finish a group of update operations on a virtual NVRAM partition |
| * |
| * Locks required: PHY_LOCK if type==*PHY* |
| * Returns: 0, EINVAL (bad type/offset/length), EACCES (if PHY_LOCK required and not held) |
| */ |
| #define MC_CMD_NVRAM_UPDATE_FINISH 0x3c |
| #define MC_CMD_NVRAM_UPDATE_FINISH_IN_LEN 8 |
| #define MC_CMD_NVRAM_UPDATE_FINISH_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_UPDATE_FINISH_IN_REBOOT_OFST 4 |
| #define MC_CMD_NVRAM_UPDATE_FINISH_OUT_LEN 0 |
| |
| /* MC_CMD_REBOOT: |
| * Reboot the MC. |
| * |
| * The AFTER_ASSERTION flag is intended to be used when the driver notices |
| * an assertion failure (at which point it is expected to perform a complete |
| * tear down and reinitialise), to allow both ports to reset the MC once |
| * in an atomic fashion. |
| * |
| * Production mc firmwares are generally compiled with REBOOT_ON_ASSERT=1, |
| * which means that they will automatically reboot out of the assertion |
| * handler, so this is in practise an optional operation. It is still |
| * recommended that drivers execute this to support custom firmwares |
| * with REBOOT_ON_ASSERT=0. |
| * |
| * Locks required: NONE |
| * Returns: Nothing. You get back a response with ERR=1, DATALEN=0 |
| */ |
| #define MC_CMD_REBOOT 0x3d |
| #define MC_CMD_REBOOT_IN_LEN 4 |
| #define MC_CMD_REBOOT_IN_FLAGS_OFST 0 |
| #define MC_CMD_REBOOT_FLAGS_AFTER_ASSERTION 1 |
| #define MC_CMD_REBOOT_OUT_LEN 0 |
| |
| /* MC_CMD_SCHEDINFO: |
| * Request scheduler info. from the MC. |
| * |
| * Locks required: NONE |
| * Returns: An array of (timeslice,maximum overrun), one for each thread, |
| * in ascending order of thread address.s |
| */ |
| #define MC_CMD_SCHEDINFO 0x3e |
| #define MC_CMD_SCHEDINFO_IN_LEN 0 |
| |
| |
| /* MC_CMD_SET_REBOOT_MODE: (debug) |
| * Set the mode for the next MC reboot. |
| * |
| * Locks required: NONE |
| * |
| * Sets the reboot mode to the specified value. Returns the old mode. |
| */ |
| #define MC_CMD_REBOOT_MODE 0x3f |
| #define MC_CMD_REBOOT_MODE_IN_LEN 4 |
| #define MC_CMD_REBOOT_MODE_IN_VALUE_OFST 0 |
| #define MC_CMD_REBOOT_MODE_OUT_LEN 4 |
| #define MC_CMD_REBOOT_MODE_OUT_VALUE_OFST 0 |
| #define MC_CMD_REBOOT_MODE_NORMAL 0 |
| #define MC_CMD_REBOOT_MODE_SNAPPER 3 |
| |
| /* MC_CMD_DEBUG_LOG: |
| * Null request/response command (debug) |
| * - sequence number is always zero |
| * - only supported on the UART interface |
| * (the same set of bytes is delivered as an |
| * event over PCI) |
| */ |
| #define MC_CMD_DEBUG_LOG 0x40 |
| #define MC_CMD_DEBUG_LOG_IN_LEN 0 |
| #define MC_CMD_DEBUG_LOG_OUT_LEN 0 |
| |
| /* Generic sensor enumeration. Note that a dual port NIC |
| * will EITHER expose PHY_COMMON_TEMP OR PHY0_TEMP and |
| * PHY1_TEMP depending on whether there is a single sensor |
| * in the vicinity of the two port, or one per port. |
| */ |
| #define MC_CMD_SENSOR_CONTROLLER_TEMP 0 /* degC */ |
| #define MC_CMD_SENSOR_PHY_COMMON_TEMP 1 /* degC */ |
| #define MC_CMD_SENSOR_CONTROLLER_COOLING 2 /* bool */ |
| #define MC_CMD_SENSOR_PHY0_TEMP 3 /* degC */ |
| #define MC_CMD_SENSOR_PHY0_COOLING 4 /* bool */ |
| #define MC_CMD_SENSOR_PHY1_TEMP 5 /* degC */ |
| #define MC_CMD_SENSOR_PHY1_COOLING 6 /* bool */ |
| #define MC_CMD_SENSOR_IN_1V0 7 /* mV */ |
| #define MC_CMD_SENSOR_IN_1V2 8 /* mV */ |
| #define MC_CMD_SENSOR_IN_1V8 9 /* mV */ |
| #define MC_CMD_SENSOR_IN_2V5 10 /* mV */ |
| #define MC_CMD_SENSOR_IN_3V3 11 /* mV */ |
| #define MC_CMD_SENSOR_IN_12V0 12 /* mV */ |
| |
| |
| /* Sensor state */ |
| #define MC_CMD_SENSOR_STATE_OK 0 |
| #define MC_CMD_SENSOR_STATE_WARNING 1 |
| #define MC_CMD_SENSOR_STATE_FATAL 2 |
| #define MC_CMD_SENSOR_STATE_BROKEN 3 |
| |
| /* MC_CMD_SENSOR_INFO: |
| * Returns information about every available sensor. |
| * |
| * Each sensor has a single (16bit) value, and a corresponding state. |
| * The mapping between value and sensor is nominally determined by the |
| * MC, but in practise is implemented as zero (BROKEN), one (TEMPERATURE), |
| * or two (VOLTAGE) ranges per sensor per state. |
| * |
| * This call returns a mask (32bit) of the sensors that are supported |
| * by this platform, then an array (indexed by MC_CMD_SENSOR) of byte |
| * offsets to the per-sensor arrays. Each sensor array has four 16bit |
| * numbers, min1, max1, min2, max2. |
| * |
| * Locks required: None |
| * Returns: 0 |
| */ |
| #define MC_CMD_SENSOR_INFO 0x41 |
| #define MC_CMD_SENSOR_INFO_IN_LEN 0 |
| #define MC_CMD_SENSOR_INFO_OUT_MASK_OFST 0 |
| #define MC_CMD_SENSOR_INFO_OUT_OFFSET_OFST(_x) \ |
| (4 + (_x)) |
| #define MC_CMD_SENSOR_INFO_OUT_MIN1_OFST(_ofst) \ |
| ((_ofst) + 0) |
| #define MC_CMD_SENSOR_INFO_OUT_MAX1_OFST(_ofst) \ |
| ((_ofst) + 2) |
| #define MC_CMD_SENSOR_INFO_OUT_MIN2_OFST(_ofst) \ |
| ((_ofst) + 4) |
| #define MC_CMD_SENSOR_INFO_OUT_MAX2_OFST(_ofst) \ |
| ((_ofst) + 6) |
| |
| /* MC_CMD_READ_SENSORS |
| * Returns the current reading from each sensor |
| * |
| * Returns a sparse array of sensor readings (indexed by the sensor |
| * type) into host memory. Each array element is a dword. |
| * |
| * The MC will send a SENSOREVT event every time any sensor changes state. The |
| * driver is responsible for ensuring that it doesn't miss any events. The board |
| * will function normally if all sensors are in STATE_OK or state_WARNING. |
| * Otherwise the board should not be expected to function. |
| */ |
| #define MC_CMD_READ_SENSORS 0x42 |
| #define MC_CMD_READ_SENSORS_IN_LEN 8 |
| #define MC_CMD_READ_SENSORS_IN_DMA_ADDR_LO_OFST 0 |
| #define MC_CMD_READ_SENSORS_IN_DMA_ADDR_HI_OFST 4 |
| #define MC_CMD_READ_SENSORS_OUT_LEN 0 |
| |
| /* Sensor reading fields */ |
| #define MC_CMD_READ_SENSOR_VALUE_LBN 0 |
| #define MC_CMD_READ_SENSOR_VALUE_WIDTH 16 |
| #define MC_CMD_READ_SENSOR_STATE_LBN 16 |
| #define MC_CMD_READ_SENSOR_STATE_WIDTH 8 |
| |
| |
| /* MC_CMD_GET_PHY_STATE: |
| * Report current state of PHY. A "zombie" PHY is a PHY that has failed to |
| * boot (e.g. due to missing or corrupted firmware). |
| * |
| * Locks required: None |
| * Return code: 0 |
| */ |
| #define MC_CMD_GET_PHY_STATE 0x43 |
| |
| #define MC_CMD_GET_PHY_STATE_IN_LEN 0 |
| #define MC_CMD_GET_PHY_STATE_OUT_LEN 4 |
| #define MC_CMD_GET_PHY_STATE_STATE_OFST 0 |
| /* PHY state enumeration: */ |
| #define MC_CMD_PHY_STATE_OK 1 |
| #define MC_CMD_PHY_STATE_ZOMBIE 2 |
| |
| |
| /* 802.1Qbb control. 8 Tx queues that map to priorities 0 - 7. Use all 1s to |
| * disable 802.Qbb for a given priority. */ |
| #define MC_CMD_SETUP_8021QBB 0x44 |
| #define MC_CMD_SETUP_8021QBB_IN_LEN 32 |
| #define MC_CMD_SETUP_8021QBB_OUT_LEN 0 |
| #define MC_CMD_SETUP_8021QBB_IN_TXQS_OFFST 0 |
| |
| |
| /* MC_CMD_WOL_FILTER_GET: |
| * Retrieve ID of any WoL filters |
| * |
| * Locks required: None |
| * Returns: 0, ENOSYS |
| */ |
| #define MC_CMD_WOL_FILTER_GET 0x45 |
| #define MC_CMD_WOL_FILTER_GET_IN_LEN 0 |
| #define MC_CMD_WOL_FILTER_GET_OUT_LEN 4 |
| #define MC_CMD_WOL_FILTER_GET_OUT_FILTER_ID_OFST 0 |
| |
| |
| /* MC_CMD_ADD_LIGHTSOUT_OFFLOAD: |
| * Offload a protocol to NIC for lights-out state |
| * |
| * Locks required: None |
| * Returns: 0, ENOSYS |
| */ |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD 0x46 |
| |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_LEN 16 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0 |
| |
| /* There is a union at offset 4, following defines overlap due to |
| * this */ |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_DATA_OFST 4 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPMAC_OFST 4 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_ARPIP_OFST 10 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSMAC_OFST 4 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSSNIPV6_OFST 10 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_IN_NSIPV6_OFST 26 |
| |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_LEN 4 |
| #define MC_CMD_ADD_LIGHTSOUT_OFFLOAD_OUT_FILTER_ID_OFST 0 |
| |
| |
| /* MC_CMD_REMOVE_LIGHTSOUT_PROTOCOL_OFFLOAD: |
| * Offload a protocol to NIC for lights-out state |
| * |
| * Locks required: None |
| * Returns: 0, ENOSYS |
| */ |
| #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD 0x47 |
| #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_LEN 8 |
| #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_OUT_LEN 0 |
| |
| #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_PROTOCOL_OFST 0 |
| #define MC_CMD_REMOVE_LIGHTSOUT_OFFLOAD_IN_FILTER_ID_OFST 4 |
| |
| /* Lights-out offload protocols enumeration */ |
| #define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_ARP 0x1 |
| #define MC_CMD_LIGHTSOUT_OFFLOAD_PROTOCOL_NS 0x2 |
| |
| |
| /* MC_CMD_MAC_RESET_RESTORE: |
| * Restore MAC after block reset |
| * |
| * Locks required: None |
| * Returns: 0 |
| */ |
| |
| #define MC_CMD_MAC_RESET_RESTORE 0x48 |
| #define MC_CMD_MAC_RESET_RESTORE_IN_LEN 0 |
| #define MC_CMD_MAC_RESET_RESTORE_OUT_LEN 0 |
| |
| |
| /* MC_CMD_TEST_ASSERT: |
| * Deliberately trigger an assert-detonation in the firmware for testing |
| * purposes (i.e. to allow tests that the driver copes gracefully). |
| * |
| * Locks required: None |
| * Returns: 0 |
| */ |
| |
| #define MC_CMD_TESTASSERT 0x49 |
| #define MC_CMD_TESTASSERT_IN_LEN 0 |
| #define MC_CMD_TESTASSERT_OUT_LEN 0 |
| |
| /* MC_CMD_WORKAROUND 0x4a |
| * |
| * Enable/Disable a given workaround. The mcfw will return EINVAL if it |
| * doesn't understand the given workaround number - which should not |
| * be treated as a hard error by client code. |
| * |
| * This op does not imply any semantics about each workaround, that's between |
| * the driver and the mcfw on a per-workaround basis. |
| * |
| * Locks required: None |
| * Returns: 0, EINVAL |
| */ |
| #define MC_CMD_WORKAROUND 0x4a |
| #define MC_CMD_WORKAROUND_IN_LEN 8 |
| #define MC_CMD_WORKAROUND_IN_TYPE_OFST 0 |
| #define MC_CMD_WORKAROUND_BUG17230 1 |
| #define MC_CMD_WORKAROUND_IN_ENABLED_OFST 4 |
| #define MC_CMD_WORKAROUND_OUT_LEN 0 |
| |
| /* MC_CMD_GET_PHY_MEDIA_INFO: |
| * Read media-specific data from PHY (e.g. SFP/SFP+ module ID information for |
| * SFP+ PHYs). |
| * |
| * The "media type" can be found via GET_PHY_CFG (GET_PHY_CFG_OUT_MEDIA_TYPE); |
| * the valid "page number" input values, and the output data, are interpreted |
| * on a per-type basis. |
| * |
| * For SFP+: PAGE=0 or 1 returns a 128-byte block read from module I2C address |
| * 0xA0 offset 0 or 0x80. |
| * Anything else: currently undefined. |
| * |
| * Locks required: None |
| * Return code: 0 |
| */ |
| #define MC_CMD_GET_PHY_MEDIA_INFO 0x4b |
| #define MC_CMD_GET_PHY_MEDIA_INFO_IN_LEN 4 |
| #define MC_CMD_GET_PHY_MEDIA_INFO_IN_PAGE_OFST 0 |
| #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_LEN(_num_bytes) (4 + (_num_bytes)) |
| #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATALEN_OFST 0 |
| #define MC_CMD_GET_PHY_MEDIA_INFO_OUT_DATA_OFST 4 |
| |
| /* MC_CMD_NVRAM_TEST: |
| * Test a particular NVRAM partition for valid contents (where "valid" |
| * depends on the type of partition). |
| * |
| * Locks required: None |
| * Return code: 0 |
| */ |
| #define MC_CMD_NVRAM_TEST 0x4c |
| #define MC_CMD_NVRAM_TEST_IN_LEN 4 |
| #define MC_CMD_NVRAM_TEST_IN_TYPE_OFST 0 |
| #define MC_CMD_NVRAM_TEST_OUT_LEN 4 |
| #define MC_CMD_NVRAM_TEST_OUT_RESULT_OFST 0 |
| #define MC_CMD_NVRAM_TEST_PASS 0 |
| #define MC_CMD_NVRAM_TEST_FAIL 1 |
| #define MC_CMD_NVRAM_TEST_NOTSUPP 2 |
| |
| /* MC_CMD_MRSFP_TWEAK: (debug) |
| * Read status and/or set parameters for the "mrsfp" driver in mr_rusty builds. |
| * I2C I/O expander bits are always read; if equaliser parameters are supplied, |
| * they are configured first. |
| * |
| * Locks required: None |
| * Return code: 0, EINVAL |
| */ |
| #define MC_CMD_MRSFP_TWEAK 0x4d |
| #define MC_CMD_MRSFP_TWEAK_IN_LEN_READ_ONLY 0 |
| #define MC_CMD_MRSFP_TWEAK_IN_LEN_EQ_CONFIG 16 |
| #define MC_CMD_MRSFP_TWEAK_IN_TXEQ_LEVEL_OFST 0 /* 0-6 low->high de-emph. */ |
| #define MC_CMD_MRSFP_TWEAK_IN_TXEQ_DT_CFG_OFST 4 /* 0-8 low->high ref.V */ |
| #define MC_CMD_MRSFP_TWEAK_IN_RXEQ_BOOST_OFST 8 /* 0-8 low->high boost */ |
| #define MC_CMD_MRSFP_TWEAK_IN_RXEQ_DT_CFG_OFST 12 /* 0-8 low->high ref.V */ |
| #define MC_CMD_MRSFP_TWEAK_OUT_LEN 12 |
| #define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_INPUTS_OFST 0 /* input bits */ |
| #define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_OUTPUTS_OFST 4 /* output bits */ |
| #define MC_CMD_MRSFP_TWEAK_OUT_IOEXP_DIRECTION_OFST 8 /* dirs: 0=out, 1=in */ |
| |
| /* MC_CMD_TEST_HACK: (debug (unsurprisingly)) |
| * Change bits of network port state for test purposes in ways that would never be |
| * useful in normal operation and so need a special command to change. */ |
| #define MC_CMD_TEST_HACK 0x2f |
| #define MC_CMD_TEST_HACK_IN_LEN 8 |
| #define MC_CMD_TEST_HACK_IN_TXPAD_OFST 0 |
| #define MC_CMD_TEST_HACK_IN_TXPAD_AUTO 0 /* Let the MC manage things */ |
| #define MC_CMD_TEST_HACK_IN_TXPAD_ON 1 /* Force on */ |
| #define MC_CMD_TEST_HACK_IN_TXPAD_OFF 2 /* Force on */ |
| #define MC_CMD_TEST_HACK_IN_IPG_OFST 4 /* Takes a value in bits */ |
| #define MC_CMD_TEST_HACK_IN_IPG_AUTO 0 /* The MC picks the value */ |
| #define MC_CMD_TEST_HACK_OUT_LEN 0 |
| |
| /* MC_CMD_SENSOR_SET_LIMS: (debug) (mostly) adjust the sensor limits. This |
| * is a warranty-voiding operation. |
| * |
| * IN: sensor identifier (one of the enumeration starting with MC_CMD_SENSOR_CONTROLLER_TEMP |
| * followed by 4 32-bit values: min(warning) max(warning), min(fatal), max(fatal). Which |
| * of these limits are meaningful and what their interpretation is is sensor-specific. |
| * |
| * OUT: nothing |
| * |
| * Returns: ENOENT if the sensor specified does not exist, EINVAL if the limits are |
| * out of range. |
| */ |
| #define MC_CMD_SENSOR_SET_LIMS 0x4e |
| #define MC_CMD_SENSOR_SET_LIMS_IN_LEN 20 |
| #define MC_CMD_SENSOR_SET_LIMS_IN_SENSOR_OFST 0 |
| #define MC_CMD_SENSOR_SET_LIMS_IN_LOW0_OFST 4 |
| #define MC_CMD_SENSOR_SET_LIMS_IN_HI0_OFST 8 |
| #define MC_CMD_SENSOR_SET_LIMS_IN_LOW1_OFST 12 |
| #define MC_CMD_SENSOR_SET_LIMS_IN_HI1_OFST 16 |
| |
| /* Do NOT add new commands beyond 0x4f as part of 3.0 : 0x50 - 0x7f will be |
| * used for post-3.0 extensions. If you run out of space, look for gaps or |
| * commands that are unused in the existing range. */ |
| |
| #endif /* MCDI_PCOL_H */ |