| Qualcomm QPNP power-on |
| |
| The qpnp-power-on is a driver which supports the power-on(PON) |
| peripheral on Qualcomm PMICs. The supported functionality includes |
| power on/off reason, key press/release detection, PMIC reset configurations |
| and other PON specific features. The PON module supports multiple physical |
| power-on (KPDPWR_N, CBLPWR) and reset (KPDPWR_N, RESIN, KPDPWR+RESIN) sources. |
| This peripheral is connected to the host processor via the SPMI interface. |
| |
| Required properties: |
| - compatible: Must be "qcom,qpnp-power-on" |
| - reg: Specifies the SPMI address and size for this PON (power-on) |
| peripheral. |
| - interrupts: Specifies the interrupt associated with PON. |
| - interrupt-names: Specify the interrupt names associated with interrupts. |
| Must be one of "kpdpwr", "kpdpwr-bark", "resin", |
| "resin-bark", "cblpwr", "kpdpwr-resin-bark".Bark |
| interrupts are associated with system reset |
| configuration to allow default reset configuration to |
| be activated. If system reset configuration is not |
| supported then bark interrupts are nops. Additionally, |
| the "pmic-wd-bark" interrupt can be added if the system |
| needs to handle PMIC watch dog barks. |
| |
| Optional properties: |
| - qcom,pon-dbc-delay The debounce delay for the power-key interrupt |
| specified in us. |
| Possible values for GEN1 PON are: |
| 15625, 31250, 62500, 125000, 250000, 500000, |
| 1000000 and 2000000. |
| Possible values for GEN2 PON are: |
| 62, 123, 245, 489, 977, 1954, 3907, 7813, |
| 15625, 31250, 62500, 125000 and 250000. |
| Intermediate value is rounded down to the |
| nearest valid value. |
| - qcom,pon_1 ...pon_n These represent the child nodes which describe |
| the properties (reset, key) for each of the pon |
| reset source. All the child nodes are optional. |
| If none of them is specified, the driver fails |
| to register. |
| - qcom,system-reset Specifies that this PON peripheral can be used |
| to reset the system. This property can only be |
| used by one device on the system. It is an |
| error to include it more than once. |
| - qcom,s3-debounce The debounce delay for stage3 reset trigger in |
| secs. The values range from 0 to 128. |
| - qcom,s3-src The source for stage 3 reset. It can be one of |
| "kpdpwr", "resin", "kpdpwr-or-resin" or |
| "kpdpwr-and-resin". The default value is |
| "kpdpwr-and-resin". |
| - qcom,uvlo-panic If this property is present, the device will |
| set to panic during reboot if this reboot is |
| due to under voltage lock out. |
| - qcom,clear-warm-reset Specifies that the WARM_RESET reason registers |
| need to be cleared for this target. The |
| property is used for the targets which have a |
| hardware feature to catch resets which aren't |
| triggered by the MSM. |
| In such cases clearing WARM_REASON registers |
| across MSM resets keeps the registers in good |
| state. |
| - qcom,secondary-pon-reset Boolean property which indicates that the PON |
| peripheral is a secondary PON device which |
| needs to be configured during reset in addition |
| to the primary PON device that is configured |
| for system reset through qcom,system-reset |
| property. |
| This should not be defined along with the |
| qcom,system-reset property. |
| - qcom,store-hard-reset-reason Boolean property which if set will store the |
| hardware reset reason to SOFT_RB_SPARE register |
| of the core PMIC PON peripheral. |
| - qcom,warm-reset-poweroff-type Poweroff type required to be configured on |
| PS_HOLD reset control register when the system |
| goes for warm reset. If this property is not |
| specified, then the default type, warm reset |
| will be configured to PS_HOLD reset control |
| register. |
| - qcom,hard-reset-poweroff-type Same description as qcom,warm-reset-poweroff- |
| type but this applies for the system hard reset |
| case. |
| - qcom,shutdown-poweroff-type Same description as qcom,warm-reset-poweroff- |
| type but this applies for the system shutdown |
| case. |
| |
| |
| All the below properties are in the sub-node section (properties of the child |
| node). |
| |
| Sub-nodes (if defined) should belong to either a PON configuration or a |
| regulator configuration. |
| |
| Regulator sub-node required properties: |
| - regulator-name Regulator name for the PON regulator that |
| is being configured. |
| - qcom,pon-spare-reg-addr Register offset from the base address of the |
| PON peripheral that needs to be configured for |
| the regulator being controlled. |
| - qcom,pon-spare-reg-bit Bit position in the specified register that |
| needs to be configured for the regulator being |
| controlled. |
| |
| PON sub-node required properties: |
| - qcom,pon-type The type of PON/RESET source. The driver |
| currently supports KPDPWR(0), RESIN(1) and |
| CBLPWR(2) pon/reset sources. |
| |
| PON sub-node optional properties: |
| - qcom,pull-up The initial state of the reset pin under |
| consideration. |
| 0 = No pull-up |
| 1 = pull-up enabled |
| This property is set to '0' if not specified. |
| - qcom,support-reset Indicates if this PON source supports |
| reset functionality. |
| 0 = Not supported |
| 1 = Supported |
| If this property is not defined, then do not |
| modify S2 reset values. |
| - qcom,use-bark Specify if this pon type needs to handle bark |
| irq. |
| - linux,code The input key-code associated with the reset |
| source. |
| The reset source in its default configuration |
| can be used to support standard keys. |
| |
| The below mentioned properties are required only when qcom,support-reset DT |
| property is defined and is set to 1. |
| |
| - qcom,s1-timer The debounce timer for the BARK interrupt for |
| that reset source. Value is specified in ms. |
| Supported values are: |
| - 0, 32, 56, 80, 128, 184, 272, 408, 608, 904 |
| 1352, 2048, 3072, 4480, 6720, 10256 |
| - qcom,s2-timer The debounce timer for the S2 reset specified |
| in ms. On the expiry of this timer, the PMIC |
| executes the reset sequence. |
| Supported values are: |
| - 0, 10, 50, 100, 250, 500, 1000, 2000 |
| - qcom,s2-type The type of reset associated with this source. |
| The supported resets are: |
| SOFT(0), WARM(1), SHUTDOWN(4), HARD(7) |
| |
| Example: |
| qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| interrupts = <0x0 0x8 0x0>, |
| <0x0 0x8 0x1>, |
| <0x0 0x8 0x4>, |
| <0x0 0x8 0x5>; |
| interrupt-names = "kpdpwr", "resin", |
| "resin-bark", "kpdpwr-resin-bark"; |
| qcom,pon-dbc-delay = <15625>; |
| qcom,system-reset; |
| qcom,s3-debounce = <32>; |
| qcom,s3-src = "resin"; |
| qcom,clear-warm-reset; |
| qcom,store-hard-reset-reason; |
| |
| qcom,pon_1 { |
| qcom,pon-type = <0>; |
| qcom,pull-up = <1>; |
| linux,code = <116>; |
| }; |
| |
| qcom,pon_2 { |
| qcom,pon-type = <1>; |
| qcom,support-reset = <1>; |
| qcom,pull-up = <1>; |
| qcom,s1-timer = <0>; |
| qcom,s2-timer = <2000>; |
| qcom,s2-type = <1>; |
| linux,code = <114>; |
| qcom,use-bark; |
| }; |
| |
| qcom,pon_3 { |
| qcom,pon-type = <3>; |
| qcom,support-reset = <1>; |
| qcom,s1-timer = <6720>; |
| qcom,s2-timer = <2000>; |
| qcom,s2-type = <7>; |
| qcom,pull-up = <1>; |
| qcom,use-bark; |
| }; |
| }; |
| qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| qcom,secondary-pon-reset; |
| qcom,hard-reset-poweroff-type = <PON_POWER_OFF_SHUTDOWN>; |
| |
| pon_perph_reg: qcom,pon_perph_reg { |
| regulator-name = "pon_spare_reg"; |
| qcom,pon-spare-reg-addr = <0x8c>; |
| qcom,pon-spare-reg-bit = <1>; |
| }; |
| }; |