Documentation/devicetree/bindings/usb/msm-phy.txt - kernel/msm-4.9 - Gitiles

 MSM USB PHY transceivers

 HSUSB PHY

 Required properties:
  - compatible: Should be "qcom,usb-hsphy-snps-femto"
  - reg: Address and length of the register set for the device
    Required regs are:
 	"hsusb_phy_base" : the base register for the PHY
  - <supply-name>-supply: phandle to the regulator device tree node
    Required "supply-name" examples are:
 	"vdd" : vdd supply for HSPHY digital circuit operation
 	"vdda18" : 1.8v supply for HSPHY
 	"vdda33" : 3.3v supply for HSPHY
  - clocks: a list of phandles to the PHY clocks. Use as per
    Documentation/devicetree/bindings/clock/clock-bindings.txt
  - clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
    property. "ref_clk_src" is a mandatory clock.
  - qcom,vdd-voltage-level: This property must be a list of three integer
    values (no, min, max) where each value represents either a voltage in
    microvolts or a value corresponding to voltage corner
  - resets: reset specifier pair consists of phandle for the reset controller
    and reset lines used by this controller.
  - reset-names: reset signal name strings sorted in the same order as the resets
    property.

 Example:
 	hsphy@f9200000 {
 		compatible = "qcom,usb-hsphy-snps-femto";
 		reg = <0xff1000 0x400>;
 		vdd-supply = <&pm8841_s2_corner>;
 		vdda18-supply = <&pm8941_l6>;
 		vdda33-supply = <&pm8941_l24>;
 		qcom,vdd-voltage-level = <0 872000 872000>;
 	};

 SSUSB-QMP PHY

 Required properties:
  - compatible: Should be "qcom,usb-ssphy-qmp", "qcom,usb-ssphy-qmp-v1" or
    "qcom,usb-ssphy-qmp-v2" or "qcom,usb-ssphy-qmp-usb3-or-dp" or
    "qcom,usb-ssphy-qmp-dp-combo"
  - reg: Address and length of the register set for the device
    Required regs are:
    "qmp_phy_base" : QMP PHY Base register set.
  - "vls_clamp_reg" : top-level CSR register to be written to enable phy vls
    clamp which allows phy to detect autonomous mode. (optional for USB DP PHY)
  - <supply-name>-supply: phandle to the regulator device tree node
    Required "supply-name" examples are:
 	"vdd" : vdd supply for SSPHY digital circuit operation
 	"core" : high-voltage analog supply for SSPHY
  - clocks: a list of phandles to the PHY clocks. Use as per
    Documentation/devicetree/bindings/clock/clock-bindings.txt
  - clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
    property. Required clocks are "aux_clk" and "pipe_clk".
  - qcom,vdd-voltage-level: This property must be a list of three integer
    values (no, min, max) where each value represents either a voltage in
    microvolts or a value corresponding to voltage corner
  - qcom,qmp-phy-init-seq: QMP PHY initialization sequence with reg offset, its
    value, delay after register write. It is not must property to have for emulation.
  - qcom,qmp-phy-reg-offset: Provides important phy register offsets in an order
    defined in the phy driver.
    Provide below mentioned register offsets in order for non USB DP combo PHY:
    USB3_PHY_PCS_STATUS,
    USB3_PHY_AUTONOMOUS_MODE_CTRL,
    USB3_PHY_LFPS_RXTERM_IRQ_CLEAR,
    USB3_PHY_POWER_DOWN_CONTROL,
    USB3_PHY_SW_RESET,
    USB3_PHY_START

    In addion to above following set of registers offset needed for USB DP combo PHY in mentioned order:
    USB3_DP_DP_PHY_PD_CTL,
    USB3_DP_COM_POWER_DOWN_CTRL,
    USB3_DP_COM_SW_RESET,
    USB3_DP_COM_RESET_OVRD_CTRL,
    USB3_DP_COM_PHY_MODE_CTRL,
    USB3_DP_COM_TYPEC_CTRL,
    USB3_DP_COM_SWI_CTRL,
    USB3_PCS_MISC_CLAMP_ENABLE

    Optional register for configuring USB Type-C port select if available:
    USB3_PHY_PCS_MISC_TYPEC_CTRL

 - resets: reset specifier pair consists of phandle for the reset controller
   and reset lines used by this controller.
 - reset-names: reset signal name strings sorted in the same order as the resets
   property.

 Optional properties:
  - reg: Additional register set of address and length to control QMP PHY are:
    "tcsr_usb3_dp_phymode" : top-level CSR register to be written to select
    super speed usb qmp phy.
  - clocks: a list of phandles to the PHY clocks. Use as per
    Documentation/devicetree/bindings/clock/clock-bindings.txt
  - clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
    property. "cfg_ahb_clk" and "com_aux_clk" are an optional clocks.
  - qcom,vbus-valid-override: If present, indicates VBUS pin is not connected to
    the USB PHY and the controller must rely on external VBUS notification in
    order to manually relay the notification to the SSPHY.
  - qcom,emulation: Indicates that we are running on emulation platform.
  - qcom,core-voltage-level: This property must be a list of three integer
    values (no, min, max) where each value represents either a voltage in
    microvolts or a value corresponding to voltage corner.
  - "pcs_clamp_enable_reg" : Clamps the phy data inputs and enables USB3
    autonomous mode.

 Example:
 	ssphy0: ssphy@f9b38000 {
 		compatible = "qcom,usb-ssphy-qmp";
 		reg = <0xf9b38000 0x16c>,
 			<0x01947244 0x4>;
 		reg-names = "qmp_phy_base",
 			"vls_clamp_reg";
 		vdd-supply = <&pmd9635_l4>;
 		vdda18-supply = <&pmd9635_l8>;
 		qcom,vdd-voltage-level = <0 900000 1050000>;
 		qcom,vbus-valid-override;

 		clocks = <&clock_gcc clk_gcc_usb3_phy_aux_clk>,
 			 <&clock_gcc clk_gcc_usb3_phy_pipe_clk>,
 			 <&clock_gcc clk_gcc_usb_phy_cfg_ahb2phy_clk>,
 			 <&clock_gcc clk_ln_bb_clk1>,
 			 <&clock_gcc clk_gcc_usb3_clkref_clk>;

 		clock-names = "aux_clk", "pipe_clk", "cfg_ahb_clk",
 			      "ref_clk_src", "ref_clk";

 		resets = <&clock_gcc GCC_USB3_PHY_BCR>,
 			<&clock_gcc GCC_USB3PHY_PHY_BCR>;
 		reset-names = "phy_reset",
 				"phy_phy_reset";

 	};

 QUSB2 High-Speed PHY

 Required properties:
  - compatible: Should be "qcom,qusb2phy" or "qcom,qusb2phy-v2"
  - reg: Address and length of the QUSB2 PHY register set
  - reg-names: Should be "qusb_phy_base".
  - <supply-name>-supply: phandle to the regulator device tree node
    Required supplies are:
 	"vdd" : vdd supply for digital circuit operation
 	"vdda18" : 1.8v high-voltage analog supply
 	"vdda33" : 3.3v high-voltage analog supply
  - clocks: a list of phandles to the PHY clocks. Use as per
    Documentation/devicetree/bindings/clock/clock-bindings.txt
  - clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
    property. "ref_clk_src" is a mandatory clock.
  - qcom,vdd-voltage-level: This property must be a list of three integer
    values (no, min, max) where each value represents either a voltage in
    microvolts or a value corresponding to voltage corner
  - phy_type: Should be one of "ulpi" or "utmi". ChipIdea core uses "ulpi" mode.
  - resets: reset specifier pair consists of phandle for the reset controller
    and reset lines used by this controller.
  - reset-names: reset signal name strings sorted in the same order as the resets
    property.
  - qcom,qusb-phy-reg-offset: Provides important phy register offsets in an order defined in phy driver.

 Optional properties:
  - reg-names: Additional registers corresponding with the following:
    "efuse_addr": EFUSE address to read and update analog tune parameter.
    "emu_phy_base" : phy base address used for programming emulation target phy.
    "ref_clk_addr" : ref_clk bcr address used for on/off ref_clk before reset.
    "tcsr_clamp_dig_n" : To enable/disable digital clamp to the phy. When
    de-asserted, it will prevent random leakage from qusb2 phy resulting from
    out of sequence turn on/off of 1p8, 3p3 and DVDD regulators.
    "refgen_north_bg_reg" : address used to read REFGEN status for overriding QUSB PHY register.
  - clocks: a list of phandles to the PHY clocks. Use as per
    Documentation/devicetree/bindings/clock/clock-bindings.txt
  - clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
    property. "cfg_ahb_clk" and "ref_clk" are optional clocks.
  - qcom,qusb-phy-init-seq: QUSB PHY initialization sequence with value,reg pair.
  - qcom,qusb-phy-host-init-seq: QUSB PHY initialization sequence for host mode
    with value,reg pair.
  - qcom,emu-init-seq : emulation initialization sequence with value,reg pair.
  - qcom,phy-pll-reset-seq : emulation PLL reset sequence with value,reg pair.
  - qcom,emu-dcm-reset-seq : emulation DCM reset sequence with value,reg pair.
  - qcom,efuse-bit-pos: start bit position within EFUSE register
  - qcom,efuse-num-bits: Number of bits to read from EFUSE register
  - qcom,emulation: Indicates that we are running on emulation platform.
  - qcom,hold-reset: Indicates that hold QUSB PHY into reset state.
  - qcom,phy-clk-scheme: Should be one of "cml" or "cmos" if ref_clk_addr is provided.
  - qcom,major-rev: provide major revision number to differentiate power up sequence. default is 2.0
  - pinctrl-names/pinctrl-0/1: The GPIOs configured as output function. Names represents "active"
    state when attached in host mode and "suspend" state when detached.
  - qcom,tune2-efuse-correction: The value to be adjusted from fused value for
    improved rise/fall times.
  - nvmem-cells: specifies the handle to represent the SoC revision.
    usually it is defined by qfprom device node.
  - nvmem-cell-names: specifies the given nvmem cell name as defined in
    qfprom node.

 Example:
 	qusb_phy: qusb@f9b39000 {
 		compatible = "qcom,qusb2phy";
 		reg = <0x00079000 0x7000>;
 		reg-names = "qusb_phy_base";
 		vdd-supply = <&pm8994_s2_corner>;
 		vdda18-supply = <&pm8994_l6>;
 		vdda33-supply = <&pm8994_l24>;
 		qcom,vdd-voltage-level = <1 5 7>;
 		qcom,qusb-phy-reg-offset =
 			<0x240 /* QUSB2PHY_PORT_TUNE1 */
 			 0x1a0 /* QUSB2PHY_PLL_COMMON_STATUS_ONE */
 			 0x210 /* QUSB2PHY_PWR_CTRL1 */
 			 0x230 /* QUSB2PHY_INTR_CTRL */
 			 0x0a8 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE */
 			 0x254 /* QUSB2PHY_TEST1 */
 			 0x198>; /* QUSB2PHY_PLL_BIAS_CONTROL_2 */
 		qcom,efuse-bit-pos = <21>;
 		qcom,efuse-num-bits = <3>;

 		clocks = <&clock_rpm clk_ln_bb_clk>,
 			 <&clock_gcc clk_gcc_rx2_usb1_clkref_clk>,
 			 <&clock_gcc clk_gcc_usb_phy_cfg_ahb2phy_clk>;
 		clock-names = "ref_clk_src", "ref_clk", "cfg_ahb_clk";
 		resets = <&clock_gcc GCC_QUSB2PHY_PRIM_BCR>;
 		reset-names = "phy_reset";
 	};
	MSM USB PHY transceivers

	HSUSB PHY

	Required properties:
	- compatible: Should be "qcom,usb-hsphy-snps-femto"
	- reg: Address and length of the register set for the device
	Required regs are:
	"hsusb_phy_base" : the base register for the PHY
	- <supply-name>-supply: phandle to the regulator device tree node
	Required "supply-name" examples are:
	"vdd" : vdd supply for HSPHY digital circuit operation
	"vdda18" : 1.8v supply for HSPHY
	"vdda33" : 3.3v supply for HSPHY
	- clocks: a list of phandles to the PHY clocks. Use as per
	Documentation/devicetree/bindings/clock/clock-bindings.txt
	- clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
	property. "ref_clk_src" is a mandatory clock.
	- qcom,vdd-voltage-level: This property must be a list of three integer
	values (no, min, max) where each value represents either a voltage in
	microvolts or a value corresponding to voltage corner
	- resets: reset specifier pair consists of phandle for the reset controller
	and reset lines used by this controller.
	- reset-names: reset signal name strings sorted in the same order as the resets
	property.

	Example:
	hsphy@f9200000 {
	compatible = "qcom,usb-hsphy-snps-femto";
	reg = <0xff1000 0x400>;
	vdd-supply = <&pm8841_s2_corner>;
	vdda18-supply = <&pm8941_l6>;
	vdda33-supply = <&pm8941_l24>;
	qcom,vdd-voltage-level = <0 872000 872000>;
	};

	SSUSB-QMP PHY

	Required properties:
	- compatible: Should be "qcom,usb-ssphy-qmp", "qcom,usb-ssphy-qmp-v1" or
	"qcom,usb-ssphy-qmp-v2" or "qcom,usb-ssphy-qmp-usb3-or-dp" or
	"qcom,usb-ssphy-qmp-dp-combo"
	- reg: Address and length of the register set for the device
	Required regs are:
	"qmp_phy_base" : QMP PHY Base register set.
	- "vls_clamp_reg" : top-level CSR register to be written to enable phy vls
	clamp which allows phy to detect autonomous mode. (optional for USB DP PHY)
	- <supply-name>-supply: phandle to the regulator device tree node
	Required "supply-name" examples are:
	"vdd" : vdd supply for SSPHY digital circuit operation
	"core" : high-voltage analog supply for SSPHY
	- clocks: a list of phandles to the PHY clocks. Use as per
	Documentation/devicetree/bindings/clock/clock-bindings.txt
	- clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
	property. Required clocks are "aux_clk" and "pipe_clk".
	- qcom,vdd-voltage-level: This property must be a list of three integer
	values (no, min, max) where each value represents either a voltage in
	microvolts or a value corresponding to voltage corner
	- qcom,qmp-phy-init-seq: QMP PHY initialization sequence with reg offset, its
	value, delay after register write. It is not must property to have for emulation.
	- qcom,qmp-phy-reg-offset: Provides important phy register offsets in an order
	defined in the phy driver.
	Provide below mentioned register offsets in order for non USB DP combo PHY:
	USB3_PHY_PCS_STATUS,
	USB3_PHY_AUTONOMOUS_MODE_CTRL,
	USB3_PHY_LFPS_RXTERM_IRQ_CLEAR,
	USB3_PHY_POWER_DOWN_CONTROL,
	USB3_PHY_SW_RESET,
	USB3_PHY_START

	In addion to above following set of registers offset needed for USB DP combo PHY in mentioned order:
	USB3_DP_DP_PHY_PD_CTL,
	USB3_DP_COM_POWER_DOWN_CTRL,
	USB3_DP_COM_SW_RESET,
	USB3_DP_COM_RESET_OVRD_CTRL,
	USB3_DP_COM_PHY_MODE_CTRL,
	USB3_DP_COM_TYPEC_CTRL,
	USB3_DP_COM_SWI_CTRL,
	USB3_PCS_MISC_CLAMP_ENABLE

	Optional register for configuring USB Type-C port select if available:
	USB3_PHY_PCS_MISC_TYPEC_CTRL

	- resets: reset specifier pair consists of phandle for the reset controller
	and reset lines used by this controller.
	- reset-names: reset signal name strings sorted in the same order as the resets
	property.

	Optional properties:
	- reg: Additional register set of address and length to control QMP PHY are:
	"tcsr_usb3_dp_phymode" : top-level CSR register to be written to select
	super speed usb qmp phy.
	- clocks: a list of phandles to the PHY clocks. Use as per
	Documentation/devicetree/bindings/clock/clock-bindings.txt
	- clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
	property. "cfg_ahb_clk" and "com_aux_clk" are an optional clocks.
	- qcom,vbus-valid-override: If present, indicates VBUS pin is not connected to
	the USB PHY and the controller must rely on external VBUS notification in
	order to manually relay the notification to the SSPHY.
	- qcom,emulation: Indicates that we are running on emulation platform.
	- qcom,core-voltage-level: This property must be a list of three integer
	values (no, min, max) where each value represents either a voltage in
	microvolts or a value corresponding to voltage corner.
	- "pcs_clamp_enable_reg" : Clamps the phy data inputs and enables USB3
	autonomous mode.

	Example:
	ssphy0: ssphy@f9b38000 {
	compatible = "qcom,usb-ssphy-qmp";
	reg = <0xf9b38000 0x16c>,
	<0x01947244 0x4>;
	reg-names = "qmp_phy_base",
	"vls_clamp_reg";
	vdd-supply = <&pmd9635_l4>;
	vdda18-supply = <&pmd9635_l8>;
	qcom,vdd-voltage-level = <0 900000 1050000>;
	qcom,vbus-valid-override;

	clocks = <&clock_gcc clk_gcc_usb3_phy_aux_clk>,
	<&clock_gcc clk_gcc_usb3_phy_pipe_clk>,
	<&clock_gcc clk_gcc_usb_phy_cfg_ahb2phy_clk>,
	<&clock_gcc clk_ln_bb_clk1>,
	<&clock_gcc clk_gcc_usb3_clkref_clk>;

	clock-names = "aux_clk", "pipe_clk", "cfg_ahb_clk",
	"ref_clk_src", "ref_clk";

	resets = <&clock_gcc GCC_USB3_PHY_BCR>,
	<&clock_gcc GCC_USB3PHY_PHY_BCR>;
	reset-names = "phy_reset",
	"phy_phy_reset";

	};

	QUSB2 High-Speed PHY

	Required properties:
	- compatible: Should be "qcom,qusb2phy" or "qcom,qusb2phy-v2"
	- reg: Address and length of the QUSB2 PHY register set
	- reg-names: Should be "qusb_phy_base".
	- <supply-name>-supply: phandle to the regulator device tree node
	Required supplies are:
	"vdd" : vdd supply for digital circuit operation
	"vdda18" : 1.8v high-voltage analog supply
	"vdda33" : 3.3v high-voltage analog supply
	- clocks: a list of phandles to the PHY clocks. Use as per
	Documentation/devicetree/bindings/clock/clock-bindings.txt
	- clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
	property. "ref_clk_src" is a mandatory clock.
	- qcom,vdd-voltage-level: This property must be a list of three integer
	values (no, min, max) where each value represents either a voltage in
	microvolts or a value corresponding to voltage corner
	- phy_type: Should be one of "ulpi" or "utmi". ChipIdea core uses "ulpi" mode.
	- resets: reset specifier pair consists of phandle for the reset controller
	and reset lines used by this controller.
	- reset-names: reset signal name strings sorted in the same order as the resets
	property.
	- qcom,qusb-phy-reg-offset: Provides important phy register offsets in an order defined in phy driver.

	Optional properties:
	- reg-names: Additional registers corresponding with the following:
	"efuse_addr": EFUSE address to read and update analog tune parameter.
	"emu_phy_base" : phy base address used for programming emulation target phy.
	"ref_clk_addr" : ref_clk bcr address used for on/off ref_clk before reset.
	"tcsr_clamp_dig_n" : To enable/disable digital clamp to the phy. When
	de-asserted, it will prevent random leakage from qusb2 phy resulting from
	out of sequence turn on/off of 1p8, 3p3 and DVDD regulators.
	"refgen_north_bg_reg" : address used to read REFGEN status for overriding QUSB PHY register.
	- clocks: a list of phandles to the PHY clocks. Use as per
	Documentation/devicetree/bindings/clock/clock-bindings.txt
	- clock-names: Names of the clocks in 1-1 correspondence with the "clocks"
	property. "cfg_ahb_clk" and "ref_clk" are optional clocks.
	- qcom,qusb-phy-init-seq: QUSB PHY initialization sequence with value,reg pair.
	- qcom,qusb-phy-host-init-seq: QUSB PHY initialization sequence for host mode
	with value,reg pair.
	- qcom,emu-init-seq : emulation initialization sequence with value,reg pair.
	- qcom,phy-pll-reset-seq : emulation PLL reset sequence with value,reg pair.
	- qcom,emu-dcm-reset-seq : emulation DCM reset sequence with value,reg pair.
	- qcom,efuse-bit-pos: start bit position within EFUSE register
	- qcom,efuse-num-bits: Number of bits to read from EFUSE register
	- qcom,emulation: Indicates that we are running on emulation platform.
	- qcom,hold-reset: Indicates that hold QUSB PHY into reset state.
	- qcom,phy-clk-scheme: Should be one of "cml" or "cmos" if ref_clk_addr is provided.
	- qcom,major-rev: provide major revision number to differentiate power up sequence. default is 2.0
	- pinctrl-names/pinctrl-0/1: The GPIOs configured as output function. Names represents "active"
	state when attached in host mode and "suspend" state when detached.
	- qcom,tune2-efuse-correction: The value to be adjusted from fused value for
	improved rise/fall times.
	- nvmem-cells: specifies the handle to represent the SoC revision.
	usually it is defined by qfprom device node.
	- nvmem-cell-names: specifies the given nvmem cell name as defined in
	qfprom node.

	Example:
	qusb_phy: qusb@f9b39000 {
	compatible = "qcom,qusb2phy";
	reg = <0x00079000 0x7000>;
	reg-names = "qusb_phy_base";
	vdd-supply = <&pm8994_s2_corner>;
	vdda18-supply = <&pm8994_l6>;
	vdda33-supply = <&pm8994_l24>;
	qcom,vdd-voltage-level = <1 5 7>;
	qcom,qusb-phy-reg-offset =
	<0x240 /* QUSB2PHY_PORT_TUNE1 */
	0x1a0 /* QUSB2PHY_PLL_COMMON_STATUS_ONE */
	0x210 /* QUSB2PHY_PWR_CTRL1 */
	0x230 /* QUSB2PHY_INTR_CTRL */
	0x0a8 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE */
	0x254 /* QUSB2PHY_TEST1 */
	0x198>; /* QUSB2PHY_PLL_BIAS_CONTROL_2 */
	qcom,efuse-bit-pos = <21>;
	qcom,efuse-num-bits = <3>;

	clocks = <&clock_rpm clk_ln_bb_clk>,
	<&clock_gcc clk_gcc_rx2_usb1_clkref_clk>,
	<&clock_gcc clk_gcc_usb_phy_cfg_ahb2phy_clk>;
	clock-names = "ref_clk_src", "ref_clk", "cfg_ahb_clk";
	resets = <&clock_gcc GCC_QUSB2PHY_PRIM_BCR>;
	reset-names = "phy_reset";
	};