Gitiles
Code Review Sign In
gerrit-public.fairphone.software / kernel / msm-4.9 / a52312b88c8103e965979a79a07f6b34af82ca4b / . / sound / pci / hda / alc260_quirks.c
blob: 21ec2cb100b06e9c289b69eecc3f3ff6ceb32ebe [file] [log] [blame]
/*
* ALC260 quirk models
* included by patch_realtek.c
*/
/* ALC260 models */
enum {
ALC260_AUTO,
ALC260_BASIC,
ALC260_HP,
ALC260_HP_DC7600,
ALC260_HP_3013,
ALC260_FUJITSU_S702X,
ALC260_ACER,
ALC260_WILL,
ALC260_REPLACER_672V,
ALC260_FAVORIT100,
#ifdef CONFIG_SND_DEBUG
ALC260_TEST,
#endif
ALC260_MODEL_LAST /* last tag */
};
static const hda_nid_t alc260_dac_nids[1] = {
/* front */
0x02,
};
static const hda_nid_t alc260_adc_nids[1] = {
/* ADC0 */
0x04,
};
static const hda_nid_t alc260_adc_nids_alt[1] = {
/* ADC1 */
0x05,
};
/* NIDs used when simultaneous access to both ADCs makes sense. Note that
* alc260_capture_mixer assumes ADC0 (nid 0x04) is the first ADC.
*/
static const hda_nid_t alc260_dual_adc_nids[2] = {
/* ADC0, ADC1 */
0x04, 0x05
};
#define ALC260_DIGOUT_NID 0x03
#define ALC260_DIGIN_NID 0x06
static const struct hda_input_mux alc260_capture_source = {
.num_items = 4,
.items = {
{ "Mic", 0x0 },
{ "Front Mic", 0x1 },
{ "Line", 0x2 },
{ "CD", 0x4 },
},
};
/* On Fujitsu S702x laptops capture only makes sense from Mic/LineIn jack,
* headphone jack and the internal CD lines since these are the only pins at
* which audio can appear. For flexibility, also allow the option of
* recording the mixer output on the second ADC (ADC0 doesn't have a
* connection to the mixer output).
*/
static const struct hda_input_mux alc260_fujitsu_capture_sources[2] = {
{
.num_items = 3,
.items = {
{ "Mic/Line", 0x0 },
{ "CD", 0x4 },
{ "Headphone", 0x2 },
},
},
{
.num_items = 4,
.items = {
{ "Mic/Line", 0x0 },
{ "CD", 0x4 },
{ "Headphone", 0x2 },
{ "Mixer", 0x5 },
},
},
};
/* Acer TravelMate(/Extensa/Aspire) notebooks have similar configuration to
* the Fujitsu S702x, but jacks are marked differently.
*/
static const struct hda_input_mux alc260_acer_capture_sources[2] = {
{
.num_items = 4,
.items = {
{ "Mic", 0x0 },
{ "Line", 0x2 },
{ "CD", 0x4 },
{ "Headphone", 0x5 },
},
},
{
.num_items = 5,
.items = {
{ "Mic", 0x0 },
{ "Line", 0x2 },
{ "CD", 0x4 },
{ "Headphone", 0x6 },
{ "Mixer", 0x5 },
},
},
};
/* Maxdata Favorit 100XS */
static const struct hda_input_mux alc260_favorit100_capture_sources[2] = {
{
.num_items = 2,
.items = {
{ "Line/Mic", 0x0 },
{ "CD", 0x4 },
},
},
{
.num_items = 3,
.items = {
{ "Line/Mic", 0x0 },
{ "CD", 0x4 },
{ "Mixer", 0x5 },
},
},
};
/*
* This is just place-holder, so there's something for alc_build_pcms to look
* at when it calculates the maximum number of channels. ALC260 has no mixer
* element which allows changing the channel mode, so the verb list is
* never used.
*/
static const struct hda_channel_mode alc260_modes[1] = {
{ 2, NULL },
};
/* Mixer combinations
*
* basic: base_output + input + pc_beep + capture
* HP: base_output + input + capture_alt
* HP_3013: hp_3013 + input + capture
* fujitsu: fujitsu + capture
* acer: acer + capture
*/
static const struct snd_kcontrol_new alc260_base_output_mixer[] = {
HDA_CODEC_VOLUME("Front Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Front Playback Switch", 0x08, 2, HDA_INPUT),
HDA_CODEC_VOLUME("Headphone Playback Volume", 0x09, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Headphone Playback Switch", 0x09, 2, HDA_INPUT),
HDA_CODEC_VOLUME_MONO("Mono Playback Volume", 0x0a, 1, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE_MONO("Mono Playback Switch", 0x0a, 1, 2, HDA_INPUT),
{ } /* end */
};
static const struct snd_kcontrol_new alc260_input_mixer[] = {
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_VOLUME("Line Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("Line Playback Switch", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_VOLUME("Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_VOLUME("Front Mic Playback Volume", 0x07, 0x01, HDA_INPUT),
HDA_CODEC_MUTE("Front Mic Playback Switch", 0x07, 0x01, HDA_INPUT),
{ } /* end */
};
/* update HP, line and mono out pins according to the master switch */
static void alc260_hp_master_update(struct hda_codec *codec)
{
update_speakers(codec);
}
static int alc260_hp_master_sw_get(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
struct alc_spec *spec = codec->spec;
*ucontrol->value.integer.value = !spec->master_mute;
return 0;
}
static int alc260_hp_master_sw_put(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
struct alc_spec *spec = codec->spec;
int val = !*ucontrol->value.integer.value;
if (val == spec->master_mute)
return 0;
spec->master_mute = val;
alc260_hp_master_update(codec);
return 1;
}
static const struct snd_kcontrol_new alc260_hp_output_mixer[] = {
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Master Playback Switch",
.subdevice = HDA_SUBDEV_NID_FLAG | 0x11,
.info = snd_ctl_boolean_mono_info,
.get = alc260_hp_master_sw_get,
.put = alc260_hp_master_sw_put,
},
HDA_CODEC_VOLUME("Front Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Front Playback Switch", 0x08, 2, HDA_INPUT),
HDA_CODEC_VOLUME("Headphone Playback Volume", 0x09, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Headphone Playback Switch", 0x09, 2, HDA_INPUT),
HDA_CODEC_VOLUME_MONO("Speaker Playback Volume", 0x0a, 1, 0x0,
HDA_OUTPUT),
HDA_BIND_MUTE_MONO("Speaker Playback Switch", 0x0a, 1, 2, HDA_INPUT),
{ } /* end */
};
static const struct hda_verb alc260_hp_unsol_verbs[] = {
{0x10, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{},
};
static void alc260_hp_setup(struct hda_codec *codec)
{
struct alc_spec *spec = codec->spec;
spec->autocfg.hp_pins[0] = 0x0f;
spec->autocfg.speaker_pins[0] = 0x10;
spec->autocfg.speaker_pins[1] = 0x11;
spec->automute = 1;
spec->automute_mode = ALC_AUTOMUTE_PIN;
}
static const struct snd_kcontrol_new alc260_hp_3013_mixer[] = {
{
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.name = "Master Playback Switch",
.subdevice = HDA_SUBDEV_NID_FLAG | 0x11,
.info = snd_ctl_boolean_mono_info,
.get = alc260_hp_master_sw_get,
.put = alc260_hp_master_sw_put,
},
HDA_CODEC_VOLUME("Front Playback Volume", 0x09, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE("Front Playback Switch", 0x10, 0x0, HDA_OUTPUT),
HDA_CODEC_VOLUME("Aux-In Playback Volume", 0x07, 0x06, HDA_INPUT),
HDA_CODEC_MUTE("Aux-In Playback Switch", 0x07, 0x06, HDA_INPUT),
HDA_CODEC_VOLUME("Headphone Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE("Headphone Playback Switch", 0x15, 0x0, HDA_OUTPUT),
HDA_CODEC_VOLUME_MONO("Speaker Playback Volume", 0x0a, 1, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE_MONO("Speaker Playback Switch", 0x11, 1, 0x0, HDA_OUTPUT),
{ } /* end */
};
static void alc260_hp_3013_setup(struct hda_codec *codec)
{
struct alc_spec *spec = codec->spec;
spec->autocfg.hp_pins[0] = 0x15;
spec->autocfg.speaker_pins[0] = 0x10;
spec->autocfg.speaker_pins[1] = 0x11;
spec->automute = 1;
spec->automute_mode = ALC_AUTOMUTE_PIN;
}
static const struct hda_bind_ctls alc260_dc7600_bind_master_vol = {
.ops = &snd_hda_bind_vol,
.values = {
HDA_COMPOSE_AMP_VAL(0x08, 3, 0, HDA_OUTPUT),
HDA_COMPOSE_AMP_VAL(0x09, 3, 0, HDA_OUTPUT),
HDA_COMPOSE_AMP_VAL(0x0a, 3, 0, HDA_OUTPUT),
0
},
};
static const struct hda_bind_ctls alc260_dc7600_bind_switch = {
.ops = &snd_hda_bind_sw,
.values = {
HDA_COMPOSE_AMP_VAL(0x11, 3, 0, HDA_OUTPUT),
HDA_COMPOSE_AMP_VAL(0x15, 3, 0, HDA_OUTPUT),
0
},
};
static const struct snd_kcontrol_new alc260_hp_dc7600_mixer[] = {
HDA_BIND_VOL("Master Playback Volume", &alc260_dc7600_bind_master_vol),
HDA_BIND_SW("LineOut Playback Switch", &alc260_dc7600_bind_switch),
HDA_CODEC_MUTE("Speaker Playback Switch", 0x0f, 0x0, HDA_OUTPUT),
HDA_CODEC_MUTE("Headphone Playback Switch", 0x10, 0x0, HDA_OUTPUT),
{ } /* end */
};
static const struct hda_verb alc260_hp_3013_unsol_verbs[] = {
{0x15, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{},
};
static void alc260_hp_3012_setup(struct hda_codec *codec)
{
struct alc_spec *spec = codec->spec;
spec->autocfg.hp_pins[0] = 0x10;
spec->autocfg.speaker_pins[0] = 0x0f;
spec->autocfg.speaker_pins[1] = 0x11;
spec->autocfg.speaker_pins[2] = 0x15;
spec->automute = 1;
spec->automute_mode = ALC_AUTOMUTE_PIN;
}
/* Fujitsu S702x series laptops. ALC260 pin usage: Mic/Line jack = 0x12,
* HP jack = 0x14, CD audio = 0x16, internal speaker = 0x10.
*/
static const struct snd_kcontrol_new alc260_fujitsu_mixer[] = {
HDA_CODEC_VOLUME("Headphone Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Headphone Playback Switch", 0x08, 2, HDA_INPUT),
ALC_PIN_MODE("Headphone Jack Mode", 0x14, ALC_PIN_DIR_INOUT),
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_VOLUME("Mic/Line Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic/Line Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Mic/Line Jack Mode", 0x12, ALC_PIN_DIR_IN),
HDA_CODEC_VOLUME("Speaker Playback Volume", 0x09, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Speaker Playback Switch", 0x09, 2, HDA_INPUT),
{ } /* end */
};
/* Mixer for Acer TravelMate(/Extensa/Aspire) notebooks. Note that current
* versions of the ALC260 don't act on requests to enable mic bias from NID
* 0x0f (used to drive the headphone jack in these laptops). The ALC260
* datasheet doesn't mention this restriction. At this stage it's not clear
* whether this behaviour is intentional or is a hardware bug in chip
* revisions available in early 2006. Therefore for now allow the
* "Headphone Jack Mode" control to span all choices, but if it turns out
* that the lack of mic bias for this NID is intentional we could change the
* mode from ALC_PIN_DIR_INOUT to ALC_PIN_DIR_INOUT_NOMICBIAS.
*
* In addition, Acer TravelMate(/Extensa/Aspire) notebooks in early 2006
* don't appear to make the mic bias available from the "line" jack, even
* though the NID used for this jack (0x14) can supply it. The theory is
* that perhaps Acer have included blocking capacitors between the ALC260
* and the output jack. If this turns out to be the case for all such
* models the "Line Jack Mode" mode could be changed from ALC_PIN_DIR_INOUT
* to ALC_PIN_DIR_INOUT_NOMICBIAS.
*
* The C20x Tablet series have a mono internal speaker which is controlled
* via the chip's Mono sum widget and pin complex, so include the necessary
* controls for such models. On models without a "mono speaker" the control
* won't do anything.
*/
static const struct snd_kcontrol_new alc260_acer_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Master Playback Switch", 0x08, 2, HDA_INPUT),
ALC_PIN_MODE("Headphone Jack Mode", 0x0f, ALC_PIN_DIR_INOUT),
HDA_CODEC_VOLUME_MONO("Speaker Playback Volume", 0x0a, 1, 0x0,
HDA_OUTPUT),
HDA_BIND_MUTE_MONO("Speaker Playback Switch", 0x0a, 1, 2,
HDA_INPUT),
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_VOLUME("Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Mic Jack Mode", 0x12, ALC_PIN_DIR_IN),
HDA_CODEC_VOLUME("Line Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("Line Playback Switch", 0x07, 0x02, HDA_INPUT),
ALC_PIN_MODE("Line Jack Mode", 0x14, ALC_PIN_DIR_INOUT),
{ } /* end */
};
/* Maxdata Favorit 100XS: one output and one input (0x12) jack
*/
static const struct snd_kcontrol_new alc260_favorit100_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Master Playback Switch", 0x08, 2, HDA_INPUT),
ALC_PIN_MODE("Output Jack Mode", 0x0f, ALC_PIN_DIR_INOUT),
HDA_CODEC_VOLUME("Line/Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Line/Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Line/Mic Jack Mode", 0x12, ALC_PIN_DIR_IN),
{ } /* end */
};
/* Packard bell V7900 ALC260 pin usage: HP = 0x0f, Mic jack = 0x12,
* Line In jack = 0x14, CD audio = 0x16, pc beep = 0x17.
*/
static const struct snd_kcontrol_new alc260_will_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Master Playback Switch", 0x08, 0x2, HDA_INPUT),
HDA_CODEC_VOLUME("Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Mic Jack Mode", 0x12, ALC_PIN_DIR_IN),
HDA_CODEC_VOLUME("Line Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("Line Playback Switch", 0x07, 0x02, HDA_INPUT),
ALC_PIN_MODE("Line Jack Mode", 0x14, ALC_PIN_DIR_INOUT),
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
{ } /* end */
};
/* Replacer 672V ALC260 pin usage: Mic jack = 0x12,
* Line In jack = 0x14, ATAPI Mic = 0x13, speaker = 0x0f.
*/
static const struct snd_kcontrol_new alc260_replacer_672v_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Master Playback Switch", 0x08, 0x2, HDA_INPUT),
HDA_CODEC_VOLUME("Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Mic Jack Mode", 0x12, ALC_PIN_DIR_IN),
HDA_CODEC_VOLUME("ATAPI Mic Playback Volume", 0x07, 0x1, HDA_INPUT),
HDA_CODEC_MUTE("ATATI Mic Playback Switch", 0x07, 0x1, HDA_INPUT),
HDA_CODEC_VOLUME("Line Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("Line Playback Switch", 0x07, 0x02, HDA_INPUT),
ALC_PIN_MODE("Line Jack Mode", 0x14, ALC_PIN_DIR_INOUT),
{ } /* end */
};
/*
* initialization verbs
*/
static const struct hda_verb alc260_init_verbs[] = {
/* Line In pin widget for input */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
/* CD pin widget for input */
{0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
/* Mic1 (rear panel) pin widget for input and vref at 80% */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
/* Mic2 (front panel) pin widget for input and vref at 80% */
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
/* LINE-2 is used for line-out in rear */
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
/* select line-out */
{0x0e, AC_VERB_SET_CONNECT_SEL, 0x00},
/* LINE-OUT pin */
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
/* enable HP */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* enable Mono */
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
/* mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* set connection select to line in (default select for this ADC) */
{0x04, AC_VERB_SET_CONNECT_SEL, 0x02},
/* mute capture amp left and right */
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* set connection select to line in (default select for this ADC) */
{0x05, AC_VERB_SET_CONNECT_SEL, 0x02},
/* set vol=0 Line-Out mixer amp left and right */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* unmute pin widget amp left and right (no gain on this amp) */
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* set vol=0 HP mixer amp left and right */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* unmute pin widget amp left and right (no gain on this amp) */
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* set vol=0 Mono mixer amp left and right */
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* unmute pin widget amp left and right (no gain on this amp) */
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* unmute LINE-2 out pin */
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
/* mute analog inputs */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* mute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
/* mute Headphone out path */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
/* mute Mono out path */
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{ }
};
#if 0 /* should be identical with alc260_init_verbs? */
static const struct hda_verb alc260_hp_init_verbs[] = {
/* Headphone and output */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, 0xc0},
/* mono output */
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x40},
/* Mic1 (rear panel) pin widget for input and vref at 80% */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24},
/* Mic2 (front panel) pin widget for input and vref at 80% */
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24},
/* Line In pin widget for input */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20},
/* Line-2 pin widget for output */
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x40},
/* CD pin widget for input */
{0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20},
/* unmute amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, 0x7000},
/* set connection select to line in (default select for this ADC) */
{0x04, AC_VERB_SET_CONNECT_SEL, 0x02},
/* unmute Line-Out mixer amp left and right (volume = 0) */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, 0xb000},
/* mute pin widget amp left and right (no gain on this amp) */
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, 0x0000},
/* unmute HP mixer amp left and right (volume = 0) */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, 0xb000},
/* mute pin widget amp left and right (no gain on this amp) */
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, 0x0000},
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
/* mute analog inputs */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* Unmute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
/* Unmute Headphone out path */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
/* Unmute Mono out path */
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
{ }
};
#endif
static const struct hda_verb alc260_hp_3013_init_verbs[] = {
/* Line out and output */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x40},
/* mono output */
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x40},
/* Mic1 (rear panel) pin widget for input and vref at 80% */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24},
/* Mic2 (front panel) pin widget for input and vref at 80% */
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x24},
/* Line In pin widget for input */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20},
/* Headphone pin widget for output */
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0xc0},
/* CD pin widget for input */
{0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, 0x20},
/* unmute amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, 0x7000},
/* set connection select to line in (default select for this ADC) */
{0x04, AC_VERB_SET_CONNECT_SEL, 0x02},
/* unmute Line-Out mixer amp left and right (volume = 0) */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, 0xb000},
/* mute pin widget amp left and right (no gain on this amp) */
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, 0x0000},
/* unmute HP mixer amp left and right (volume = 0) */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, 0xb000},
/* mute pin widget amp left and right (no gain on this amp) */
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, 0x0000},
/* Amp Indexes: CD = 0x04, Line In 1 = 0x02, Mic 1 = 0x00 &
* Line In 2 = 0x03
*/
/* mute analog inputs */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
/* Amp Indexes: DAC = 0x01 & mixer = 0x00 */
/* Unmute Front out path */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
/* Unmute Headphone out path */
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
/* Unmute Mono out path */
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x00 << 8))},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, (0x7000 | (0x01 << 8))},
{ }
};
/* Initialisation sequence for ALC260 as configured in Fujitsu S702x
* laptops. ALC260 pin usage: Mic/Line jack = 0x12, HP jack = 0x14, CD
* audio = 0x16, internal speaker = 0x10.
*/
static const struct hda_verb alc260_fujitsu_init_verbs[] = {
/* Disable all GPIOs */
{0x01, AC_VERB_SET_GPIO_MASK, 0},
/* Internal speaker is connected to headphone pin */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* Headphone/Line-out jack connects to Line1 pin; make it an output */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
/* Mic/Line-in jack is connected to mic1 pin, so make it an input */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
/* Ensure all other unused pins are disabled and muted. */
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Disable digital (SPDIF) pins */
{0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
{0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
/* Ensure Line1 pin widget takes its input from the OUT1 sum bus
* when acting as an output.
*/
{0x0d, AC_VERB_SET_CONNECT_SEL, 0},
/* Start with output sum widgets muted and their output gains at min */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* Unmute HP pin widget amp left and right (no equiv mixer ctrl) */
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute Line1 pin widget output buffer since it starts as an output.
* If the pin mode is changed by the user the pin mode control will
* take care of enabling the pin's input/output buffers as needed.
* Therefore there's no need to enable the input buffer at this
* stage.
*/
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute input buffer of pin widget used for Line-in (no equiv
* mixer ctrl)
*/
{0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* Mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Set ADC connection select to match default mixer setting - line
* in (on mic1 pin)
*/
{0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Do the same for the second ADC: mute capture input amp and
* set ADC connection to line in (on mic1 pin)
*/
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Mute all inputs to mixer widget (even unconnected ones) */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
{ }
};
/* Initialisation sequence for ALC260 as configured in Acer TravelMate and
* similar laptops (adapted from Fujitsu init verbs).
*/
static const struct hda_verb alc260_acer_init_verbs[] = {
/* On TravelMate laptops, GPIO 0 enables the internal speaker and
* the headphone jack. Turn this on and rely on the standard mute
* methods whenever the user wants to turn these outputs off.
*/
{0x01, AC_VERB_SET_GPIO_MASK, 0x01},
{0x01, AC_VERB_SET_GPIO_DIRECTION, 0x01},
{0x01, AC_VERB_SET_GPIO_DATA, 0x01},
/* Internal speaker/Headphone jack is connected to Line-out pin */
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* Internal microphone/Mic jack is connected to Mic1 pin */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF50},
/* Line In jack is connected to Line1 pin */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
/* Some Acers (eg: C20x Tablets) use Mono pin for internal speaker */
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* Ensure all other unused pins are disabled and muted. */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Disable digital (SPDIF) pins */
{0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
{0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
/* Ensure Mic1 and Line1 pin widgets take input from the OUT1 sum
* bus when acting as outputs.
*/
{0x0b, AC_VERB_SET_CONNECT_SEL, 0},
{0x0d, AC_VERB_SET_CONNECT_SEL, 0},
/* Start with output sum widgets muted and their output gains at min */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* Unmute Line-out pin widget amp left and right
* (no equiv mixer ctrl)
*/
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute mono pin widget amp output (no equiv mixer ctrl) */
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute Mic1 and Line1 pin widget input buffers since they start as
* inputs. If the pin mode is changed by the user the pin mode control
* will take care of enabling the pin's input/output buffers as needed.
* Therefore there's no need to enable the input buffer at this
* stage.
*/
{0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* Mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Set ADC connection select to match default mixer setting - mic
* (on mic1 pin)
*/
{0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Do similar with the second ADC: mute capture input amp and
* set ADC connection to mic to match ALSA's default state.
*/
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Mute all inputs to mixer widget (even unconnected ones) */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
{ }
};
/* Initialisation sequence for Maxdata Favorit 100XS
* (adapted from Acer init verbs).
*/
static const struct hda_verb alc260_favorit100_init_verbs[] = {
/* GPIO 0 enables the output jack.
* Turn this on and rely on the standard mute
* methods whenever the user wants to turn these outputs off.
*/
{0x01, AC_VERB_SET_GPIO_MASK, 0x01},
{0x01, AC_VERB_SET_GPIO_DIRECTION, 0x01},
{0x01, AC_VERB_SET_GPIO_DATA, 0x01},
/* Line/Mic input jack is connected to Mic1 pin */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF50},
/* Ensure all other unused pins are disabled and muted. */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Disable digital (SPDIF) pins */
{0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
{0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
/* Ensure Mic1 and Line1 pin widgets take input from the OUT1 sum
* bus when acting as outputs.
*/
{0x0b, AC_VERB_SET_CONNECT_SEL, 0},
{0x0d, AC_VERB_SET_CONNECT_SEL, 0},
/* Start with output sum widgets muted and their output gains at min */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* Unmute Line-out pin widget amp left and right
* (no equiv mixer ctrl)
*/
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute Mic1 and Line1 pin widget input buffers since they start as
* inputs. If the pin mode is changed by the user the pin mode control
* will take care of enabling the pin's input/output buffers as needed.
* Therefore there's no need to enable the input buffer at this
* stage.
*/
{0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* Mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Set ADC connection select to match default mixer setting - mic
* (on mic1 pin)
*/
{0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Do similar with the second ADC: mute capture input amp and
* set ADC connection to mic to match ALSA's default state.
*/
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Mute all inputs to mixer widget (even unconnected ones) */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
{ }
};
static const struct hda_verb alc260_will_verbs[] = {
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
{0x0b, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x0d, AC_VERB_SET_CONNECT_SEL, 0x00},
{0x0f, AC_VERB_SET_EAPD_BTLENABLE, 0x02},
{0x1a, AC_VERB_SET_COEF_INDEX, 0x07},
{0x1a, AC_VERB_SET_PROC_COEF, 0x3040},
{}
};
static const struct hda_verb alc260_replacer_672v_verbs[] = {
{0x0f, AC_VERB_SET_EAPD_BTLENABLE, 0x02},
{0x1a, AC_VERB_SET_COEF_INDEX, 0x07},
{0x1a, AC_VERB_SET_PROC_COEF, 0x3050},
{0x01, AC_VERB_SET_GPIO_MASK, 0x01},
{0x01, AC_VERB_SET_GPIO_DIRECTION, 0x01},
{0x01, AC_VERB_SET_GPIO_DATA, 0x00},
{0x0f, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{}
};
/* toggle speaker-output according to the hp-jack state */
static void alc260_replacer_672v_automute(struct hda_codec *codec)
{
unsigned int present;
/* speaker --> GPIO Data 0, hp or spdif --> GPIO data 1 */
present = snd_hda_jack_detect(codec, 0x0f);
if (present) {
snd_hda_codec_write_cache(codec, 0x01, 0,
AC_VERB_SET_GPIO_DATA, 1);
snd_hda_codec_write_cache(codec, 0x0f, 0,
AC_VERB_SET_PIN_WIDGET_CONTROL,
PIN_HP);
} else {
snd_hda_codec_write_cache(codec, 0x01, 0,
AC_VERB_SET_GPIO_DATA, 0);
snd_hda_codec_write_cache(codec, 0x0f, 0,
AC_VERB_SET_PIN_WIDGET_CONTROL,
PIN_OUT);
}
}
static void alc260_replacer_672v_unsol_event(struct hda_codec *codec,
unsigned int res)
{
if ((res >> 26) == ALC_HP_EVENT)
alc260_replacer_672v_automute(codec);
}
static const struct hda_verb alc260_hp_dc7600_verbs[] = {
{0x05, AC_VERB_SET_CONNECT_SEL, 0x01},
{0x15, AC_VERB_SET_CONNECT_SEL, 0x01},
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
{0x10, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{0x11, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{0x15, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | ALC_HP_EVENT},
{}
};
/* Test configuration for debugging, modelled after the ALC880 test
* configuration.
*/
#ifdef CONFIG_SND_DEBUG
static const hda_nid_t alc260_test_dac_nids[1] = {
0x02,
};
static const hda_nid_t alc260_test_adc_nids[2] = {
0x04, 0x05,
};
/* For testing the ALC260, each input MUX needs its own definition since
* the signal assignments are different. This assumes that the first ADC
* is NID 0x04.
*/
static const struct hda_input_mux alc260_test_capture_sources[2] = {
{
.num_items = 7,
.items = {
{ "MIC1 pin", 0x0 },
{ "MIC2 pin", 0x1 },
{ "LINE1 pin", 0x2 },
{ "LINE2 pin", 0x3 },
{ "CD pin", 0x4 },
{ "LINE-OUT pin", 0x5 },
{ "HP-OUT pin", 0x6 },
},
},
{
.num_items = 8,
.items = {
{ "MIC1 pin", 0x0 },
{ "MIC2 pin", 0x1 },
{ "LINE1 pin", 0x2 },
{ "LINE2 pin", 0x3 },
{ "CD pin", 0x4 },
{ "Mixer", 0x5 },
{ "LINE-OUT pin", 0x6 },
{ "HP-OUT pin", 0x7 },
},
},
};
static const struct snd_kcontrol_new alc260_test_mixer[] = {
/* Output driver widgets */
HDA_CODEC_VOLUME_MONO("Mono Playback Volume", 0x0a, 1, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE_MONO("Mono Playback Switch", 0x0a, 1, 2, HDA_INPUT),
HDA_CODEC_VOLUME("LOUT2 Playback Volume", 0x09, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("LOUT2 Playback Switch", 0x09, 2, HDA_INPUT),
HDA_CODEC_VOLUME("LOUT1 Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("LOUT1 Playback Switch", 0x08, 2, HDA_INPUT),
/* Modes for retasking pin widgets
* Note: the ALC260 doesn't seem to act on requests to enable mic
* bias from NIDs 0x0f and 0x10. The ALC260 datasheet doesn't
* mention this restriction. At this stage it's not clear whether
* this behaviour is intentional or is a hardware bug in chip
* revisions available at least up until early 2006. Therefore for
* now allow the "HP-OUT" and "LINE-OUT" Mode controls to span all
* choices, but if it turns out that the lack of mic bias for these
* NIDs is intentional we could change their modes from
* ALC_PIN_DIR_INOUT to ALC_PIN_DIR_INOUT_NOMICBIAS.
*/
ALC_PIN_MODE("HP-OUT pin mode", 0x10, ALC_PIN_DIR_INOUT),
ALC_PIN_MODE("LINE-OUT pin mode", 0x0f, ALC_PIN_DIR_INOUT),
ALC_PIN_MODE("LINE2 pin mode", 0x15, ALC_PIN_DIR_INOUT),
ALC_PIN_MODE("LINE1 pin mode", 0x14, ALC_PIN_DIR_INOUT),
ALC_PIN_MODE("MIC2 pin mode", 0x13, ALC_PIN_DIR_INOUT),
ALC_PIN_MODE("MIC1 pin mode", 0x12, ALC_PIN_DIR_INOUT),
/* Loopback mixer controls */
HDA_CODEC_VOLUME("MIC1 Playback Volume", 0x07, 0x00, HDA_INPUT),
HDA_CODEC_MUTE("MIC1 Playback Switch", 0x07, 0x00, HDA_INPUT),
HDA_CODEC_VOLUME("MIC2 Playback Volume", 0x07, 0x01, HDA_INPUT),
HDA_CODEC_MUTE("MIC2 Playback Switch", 0x07, 0x01, HDA_INPUT),
HDA_CODEC_VOLUME("LINE1 Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("LINE1 Playback Switch", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_VOLUME("LINE2 Playback Volume", 0x07, 0x03, HDA_INPUT),
HDA_CODEC_MUTE("LINE2 Playback Switch", 0x07, 0x03, HDA_INPUT),
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_VOLUME("LINE-OUT loopback Playback Volume", 0x07, 0x06, HDA_INPUT),
HDA_CODEC_MUTE("LINE-OUT loopback Playback Switch", 0x07, 0x06, HDA_INPUT),
HDA_CODEC_VOLUME("HP-OUT loopback Playback Volume", 0x07, 0x7, HDA_INPUT),
HDA_CODEC_MUTE("HP-OUT loopback Playback Switch", 0x07, 0x7, HDA_INPUT),
/* Controls for GPIO pins, assuming they are configured as outputs */
ALC_GPIO_DATA_SWITCH("GPIO pin 0", 0x01, 0x01),
ALC_GPIO_DATA_SWITCH("GPIO pin 1", 0x01, 0x02),
ALC_GPIO_DATA_SWITCH("GPIO pin 2", 0x01, 0x04),
ALC_GPIO_DATA_SWITCH("GPIO pin 3", 0x01, 0x08),
/* Switches to allow the digital IO pins to be enabled. The datasheet
* is ambigious as to which NID is which; testing on laptops which
* make this output available should provide clarification.
*/
ALC_SPDIF_CTRL_SWITCH("SPDIF Playback Switch", 0x03, 0x01),
ALC_SPDIF_CTRL_SWITCH("SPDIF Capture Switch", 0x06, 0x01),
/* A switch allowing EAPD to be enabled. Some laptops seem to use
* this output to turn on an external amplifier.
*/
ALC_EAPD_CTRL_SWITCH("LINE-OUT EAPD Enable Switch", 0x0f, 0x02),
ALC_EAPD_CTRL_SWITCH("HP-OUT EAPD Enable Switch", 0x10, 0x02),
{ } /* end */
};
static const struct hda_verb alc260_test_init_verbs[] = {
/* Enable all GPIOs as outputs with an initial value of 0 */
{0x01, AC_VERB_SET_GPIO_DIRECTION, 0x0f},
{0x01, AC_VERB_SET_GPIO_DATA, 0x00},
{0x01, AC_VERB_SET_GPIO_MASK, 0x0f},
/* Enable retasking pins as output, initially without power amp */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
/* Disable digital (SPDIF) pins initially, but users can enable
* them via a mixer switch. In the case of SPDIF-out, this initverb
* payload also sets the generation to 0, output to be in "consumer"
* PCM format, copyright asserted, no pre-emphasis and no validity
* control.
*/
{0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
{0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
/* Ensure mic1, mic2, line1 and line2 pin widgets take input from the
* OUT1 sum bus when acting as an output.
*/
{0x0b, AC_VERB_SET_CONNECT_SEL, 0},
{0x0c, AC_VERB_SET_CONNECT_SEL, 0},
{0x0d, AC_VERB_SET_CONNECT_SEL, 0},
{0x0e, AC_VERB_SET_CONNECT_SEL, 0},
/* Start with output sum widgets muted and their output gains at min */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* Unmute retasking pin widget output buffers since the default
* state appears to be output. As the pin mode is changed by the
* user the pin mode control will take care of enabling the pin's
* input/output buffers as needed.
*/
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
{0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
{0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Also unmute the mono-out pin widget */
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Set ADC connection select to match default mixer setting (mic1
* pin)
*/
{0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Do the same for the second ADC: mute capture input amp and
* set ADC connection to mic1 pin
*/
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Mute all inputs to mixer widget (even unconnected ones) */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
{ }
};
#endif
/*
* ALC260 configurations
*/
static const char * const alc260_models[ALC260_MODEL_LAST] = {
[ALC260_BASIC] = "basic",
[ALC260_HP] = "hp",
[ALC260_HP_3013] = "hp-3013",
[ALC260_HP_DC7600] = "hp-dc7600",
[ALC260_FUJITSU_S702X] = "fujitsu",
[ALC260_ACER] = "acer",
[ALC260_WILL] = "will",
[ALC260_REPLACER_672V] = "replacer",
[ALC260_FAVORIT100] = "favorit100",
#ifdef CONFIG_SND_DEBUG
[ALC260_TEST] = "test",
#endif
[ALC260_AUTO] = "auto",
};
static const struct snd_pci_quirk alc260_cfg_tbl[] = {
SND_PCI_QUIRK(0x1025, 0x007b, "Acer C20x", ALC260_ACER),
SND_PCI_QUIRK(0x1025, 0x007f, "Acer", ALC260_WILL),
SND_PCI_QUIRK(0x1025, 0x008f, "Acer", ALC260_ACER),
SND_PCI_QUIRK(0x1509, 0x4540, "Favorit 100XS", ALC260_FAVORIT100),
SND_PCI_QUIRK(0x103c, 0x2808, "HP d5700", ALC260_HP_3013),
SND_PCI_QUIRK(0x103c, 0x280a, "HP d5750", ALC260_AUTO), /* no quirk */
SND_PCI_QUIRK(0x103c, 0x3010, "HP", ALC260_HP_3013),
SND_PCI_QUIRK(0x103c, 0x3011, "HP", ALC260_HP_3013),
SND_PCI_QUIRK(0x103c, 0x3012, "HP", ALC260_HP_DC7600),
SND_PCI_QUIRK(0x103c, 0x3013, "HP", ALC260_HP_3013),
SND_PCI_QUIRK(0x103c, 0x3014, "HP", ALC260_HP),
SND_PCI_QUIRK(0x103c, 0x3015, "HP", ALC260_HP),
SND_PCI_QUIRK(0x103c, 0x3016, "HP", ALC260_HP),
SND_PCI_QUIRK(0x104d, 0x81bb, "Sony VAIO", ALC260_BASIC),
SND_PCI_QUIRK(0x104d, 0x81cc, "Sony VAIO", ALC260_BASIC),
SND_PCI_QUIRK(0x104d, 0x81cd, "Sony VAIO", ALC260_BASIC),
SND_PCI_QUIRK(0x10cf, 0x1326, "Fujitsu S702X", ALC260_FUJITSU_S702X),
SND_PCI_QUIRK(0x152d, 0x0729, "CTL U553W", ALC260_BASIC),
SND_PCI_QUIRK(0x161f, 0x2057, "Replacer 672V", ALC260_REPLACER_672V),
SND_PCI_QUIRK(0x1631, 0xc017, "PB V7900", ALC260_WILL),
{}
};
static const struct alc_config_preset alc260_presets[] = {
[ALC260_BASIC] = {
.mixers = { alc260_base_output_mixer,
alc260_input_mixer },
.init_verbs = { alc260_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_dual_adc_nids),
.adc_nids = alc260_dual_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
},
[ALC260_HP] = {
.mixers = { alc260_hp_output_mixer,
alc260_input_mixer },
.init_verbs = { alc260_init_verbs,
alc260_hp_unsol_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_adc_nids_alt),
.adc_nids = alc260_adc_nids_alt,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
.unsol_event = alc_sku_unsol_event,
.setup = alc260_hp_setup,
.init_hook = alc_inithook,
},
[ALC260_HP_DC7600] = {
.mixers = { alc260_hp_dc7600_mixer,
alc260_input_mixer },
.init_verbs = { alc260_init_verbs,
alc260_hp_dc7600_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_adc_nids_alt),
.adc_nids = alc260_adc_nids_alt,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
.unsol_event = alc_sku_unsol_event,
.setup = alc260_hp_3012_setup,
.init_hook = alc_inithook,
},
[ALC260_HP_3013] = {
.mixers = { alc260_hp_3013_mixer,
alc260_input_mixer },
.init_verbs = { alc260_hp_3013_init_verbs,
alc260_hp_3013_unsol_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_adc_nids_alt),
.adc_nids = alc260_adc_nids_alt,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
.unsol_event = alc_sku_unsol_event,
.setup = alc260_hp_3013_setup,
.init_hook = alc_inithook,
},
[ALC260_FUJITSU_S702X] = {
.mixers = { alc260_fujitsu_mixer },
.init_verbs = { alc260_fujitsu_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_dual_adc_nids),
.adc_nids = alc260_dual_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.num_mux_defs = ARRAY_SIZE(alc260_fujitsu_capture_sources),
.input_mux = alc260_fujitsu_capture_sources,
},
[ALC260_ACER] = {
.mixers = { alc260_acer_mixer },
.init_verbs = { alc260_acer_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_dual_adc_nids),
.adc_nids = alc260_dual_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.num_mux_defs = ARRAY_SIZE(alc260_acer_capture_sources),
.input_mux = alc260_acer_capture_sources,
},
[ALC260_FAVORIT100] = {
.mixers = { alc260_favorit100_mixer },
.init_verbs = { alc260_favorit100_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_dual_adc_nids),
.adc_nids = alc260_dual_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.num_mux_defs = ARRAY_SIZE(alc260_favorit100_capture_sources),
.input_mux = alc260_favorit100_capture_sources,
},
[ALC260_WILL] = {
.mixers = { alc260_will_mixer },
.init_verbs = { alc260_init_verbs, alc260_will_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_adc_nids),
.adc_nids = alc260_adc_nids,
.dig_out_nid = ALC260_DIGOUT_NID,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
},
[ALC260_REPLACER_672V] = {
.mixers = { alc260_replacer_672v_mixer },
.init_verbs = { alc260_init_verbs, alc260_replacer_672v_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_adc_nids),
.adc_nids = alc260_adc_nids,
.dig_out_nid = ALC260_DIGOUT_NID,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.input_mux = &alc260_capture_source,
.unsol_event = alc260_replacer_672v_unsol_event,
.init_hook = alc260_replacer_672v_automute,
},
#ifdef CONFIG_SND_DEBUG
[ALC260_TEST] = {
.mixers = { alc260_test_mixer },
.init_verbs = { alc260_test_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_test_dac_nids),
.dac_nids = alc260_test_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_test_adc_nids),
.adc_nids = alc260_test_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.num_mux_defs = ARRAY_SIZE(alc260_test_capture_sources),
.input_mux = alc260_test_capture_sources,
},
#endif
};