drivers/block/paride/Kconfig - kernel/msm-4.9 - Gitiles

 #
 # PARIDE configuration
 #
 # PARIDE doesn't need PARPORT, but if PARPORT is configured as a module,
 # PARIDE must also be a module.  The bogus CONFIG_PARIDE_PARPORT option
 # controls the choices given to the user ...
 # PARIDE only supports PC style parports. Tough for USB or other parports...
 config PARIDE_PARPORT
 	tristate
 	depends on PARIDE!=n
 	default m if PARPORT_PC=m
 	default y if PARPORT_PC!=m

 comment "Parallel IDE high-level drivers"
 	depends on PARIDE

 config PARIDE_PD
 	tristate "Parallel port IDE disks"
 	depends on PARIDE
 	help
 	  This option enables the high-level driver for IDE-type disk devices
 	  connected through a parallel port. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  parallel port IDE driver, otherwise you should answer M to build
 	  it as a loadable module. The module will be called pd. You
 	  must also have at least one parallel port protocol driver in your
 	  system. Among the devices supported by this driver are the SyQuest
 	  EZ-135, EZ-230 and SparQ drives, the Avatar Shark and the backpack
 	  hard drives from MicroSolutions.

 config PARIDE_PCD
 	tristate "Parallel port ATAPI CD-ROMs"
 	depends on PARIDE
 	---help---
 	  This option enables the high-level driver for ATAPI CD-ROM devices
 	  connected through a parallel port. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  parallel port ATAPI CD-ROM driver, otherwise you should answer M to
 	  build it as a loadable module. The module will be called pcd. You
 	  must also have at least one parallel port protocol driver in your
 	  system. Among the devices supported by this driver are the
 	  MicroSolutions backpack CD-ROM drives and the Freecom Power CD. If
 	  you have such a CD-ROM drive, you should also say Y or M to "ISO
 	  9660 CD-ROM file system support" below, because that's the file
 	  system used on CD-ROMs.

 config PARIDE_PF
 	tristate "Parallel port ATAPI disks"
 	depends on PARIDE
 	help
 	  This option enables the high-level driver for ATAPI disk devices
 	  connected through a parallel port. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  parallel port ATAPI disk driver, otherwise you should answer M
 	  to build it as a loadable module. The module will be called pf.
 	  You must also have at least one parallel port protocol driver in
 	  your system. Among the devices supported by this driver are the
 	  MicroSolutions backpack PD/CD drive and the Imation Superdisk
 	  LS-120 drive.

 config PARIDE_PT
 	tristate "Parallel port ATAPI tapes"
 	depends on PARIDE
 	help
 	  This option enables the high-level driver for ATAPI tape devices
 	  connected through a parallel port. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  parallel port ATAPI disk driver, otherwise you should answer M
 	  to build it as a loadable module. The module will be called pt.
 	  You must also have at least one parallel port protocol driver in
 	  your system. Among the devices supported by this driver is the
 	  parallel port version of the HP 5GB drive.

 config PARIDE_PG
 	tristate "Parallel port generic ATAPI devices"
 	depends on PARIDE
 	---help---
 	  This option enables a special high-level driver for generic ATAPI
 	  devices connected through a parallel port. The driver allows user
 	  programs, such as cdrtools, to send ATAPI commands directly to a
 	  device.

 	  If you chose to build PARIDE support into your kernel, you may
 	  answer Y here to build in the parallel port generic ATAPI driver,
 	  otherwise you should answer M to build it as a loadable module. The
 	  module will be called pg.

 	  You must also have at least one parallel port protocol driver in
 	  your system.

 	  This driver implements an API loosely related to the generic SCSI
 	  driver. See <file:include/linux/pg.h>. for details.

 	  You can obtain the most recent version of cdrtools from
 	  <ftp://ftp.berlios.de/pub/cdrecord/>. Versions 1.6.1a3 and
 	  later fully support this driver.

 comment "Parallel IDE protocol modules"
 	depends on PARIDE

 config PARIDE_ATEN
 	tristate "ATEN EH-100 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the ATEN EH-100 parallel port IDE
 	  protocol. This protocol is used in some inexpensive low performance
 	  parallel port kits made in Hong Kong. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  protocol driver, otherwise you should answer M to build it as a
 	  loadable module. The module will be called aten. You must also
 	  have a high-level driver for the type of device that you want to
 	  support.

 config PARIDE_BPCK
 	tristate "MicroSolutions backpack (Series 5) protocol"
 	depends on PARIDE
 	---help---
 	  This option enables support for the Micro Solutions BACKPACK
 	  parallel port Series 5 IDE protocol.  (Most BACKPACK drives made
 	  before 1999 were Series 5) Series 5 drives will NOT always have the
 	  Series noted on the bottom of the drive. Series 6 drivers will.

 	  In other words, if your BACKPACK drive doesn't say "Series 6" on the
 	  bottom, enable this option.

 	  If you chose to build PARIDE support into your kernel, you may
 	  answer Y here to build in the protocol driver, otherwise you should
 	  answer M to build it as a loadable module.  The module will be
 	  called bpck.  You must also have a high-level driver for the type
 	  of device that you want to support.

 config PARIDE_BPCK6
 	tristate "MicroSolutions backpack (Series 6) protocol"
 	depends on PARIDE && !64BIT
 	---help---
 	  This option enables support for the Micro Solutions BACKPACK
 	  parallel port Series 6 IDE protocol.  (Most BACKPACK drives made
 	  after 1999 were Series 6) Series 6 drives will have the Series noted
 	  on the bottom of the drive.  Series 5 drivers don't always have it
 	  noted.

 	  In other words, if your BACKPACK drive says "Series 6" on the
 	  bottom, enable this option.

 	  If you chose to build PARIDE support into your kernel, you may
 	  answer Y here to build in the protocol driver, otherwise you should
 	  answer M to build it as a loadable module.  The module will be
 	  called bpck6.  You must also have a high-level driver for the type
 	  of device that you want to support.

 config PARIDE_COMM
 	tristate "DataStor Commuter protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the Commuter parallel port IDE
 	  protocol from DataStor. If you chose to build PARIDE support
 	  into your kernel, you may answer Y here to build in the protocol
 	  driver, otherwise you should answer M to build it as a loadable
 	  module. The module will be called comm. You must also have
 	  a high-level driver for the type of device that you want to support.

 config PARIDE_DSTR
 	tristate "DataStor EP-2000 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the EP-2000 parallel port IDE
 	  protocol from DataStor. If you chose to build PARIDE support
 	  into your kernel, you may answer Y here to build in the protocol
 	  driver, otherwise you should answer M to build it as a loadable
 	  module. The module will be called dstr. You must also have
 	  a high-level driver for the type of device that you want to support.

 config PARIDE_FIT2
 	tristate "FIT TD-2000 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the TD-2000 parallel port IDE
 	  protocol from Fidelity International Technology. This is a simple
 	  (low speed) adapter that is used in some portable hard drives. If
 	  you chose to build PARIDE support into your kernel, you may answer Y
 	  here to build in the protocol driver, otherwise you should answer M
 	  to build it as a loadable module. The module will be called ktti.
 	  You must also have a high-level driver for the type of device that
 	  you want to support.

 config PARIDE_FIT3
 	tristate "FIT TD-3000 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the TD-3000 parallel port IDE
 	  protocol from Fidelity International Technology. This protocol is
 	  used in newer models of their portable disk, CD-ROM and PD/CD
 	  devices. If you chose to build PARIDE support into your kernel, you
 	  may answer Y here to build in the protocol driver, otherwise you
 	  should answer M to build it as a loadable module. The module will be
 	  called fit3. You must also have a high-level driver for the type
 	  of device that you want to support.

 config PARIDE_EPAT
 	tristate "Shuttle EPAT/EPEZ protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the EPAT parallel port IDE protocol.
 	  EPAT is a parallel port IDE adapter manufactured by Shuttle
 	  Technology and widely used in devices from major vendors such as
 	  Hewlett-Packard, SyQuest, Imation and Avatar. If you chose to build
 	  PARIDE support into your kernel, you may answer Y here to build in
 	  the protocol driver, otherwise you should answer M to build it as a
 	  loadable module. The module will be called epat. You must also
 	  have a high-level driver for the type of device that you want to
 	  support.

 config PARIDE_EPATC8
 	bool "Support c7/c8 chips (EXPERIMENTAL)"
 	depends on PARIDE_EPAT && EXPERIMENTAL
 	help
 	  This option enables support for the newer Shuttle EP1284 (aka c7 and
 	  c8) chip. You need this if you are using any recent Imation SuperDisk
 	  (LS-120) drive.

 config PARIDE_EPIA
 	tristate "Shuttle EPIA protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the (obsolete) EPIA parallel port
 	  IDE protocol from Shuttle Technology. This adapter can still be
 	  found in some no-name kits. If you chose to build PARIDE support
 	  into your kernel, you may answer Y here to build in the protocol
 	  driver, otherwise you should answer M to build it as a loadable
 	  module. The module will be called epia. You must also have a
 	  high-level driver for the type of device that you want to support.

 config PARIDE_FRIQ
 	tristate "Freecom IQ ASIC-2 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for version 2 of the Freecom IQ parallel
 	  port IDE adapter.  This adapter is used by the Maxell Superdisk
 	  drive.  If you chose to build PARIDE support into your kernel, you
 	  may answer Y here to build in the protocol driver, otherwise you
 	  should answer M to build it as a loadable module. The module will be
 	  called friq. You must also have a high-level driver for the type
 	  of device that you want to support.

 config PARIDE_FRPW
 	tristate "FreeCom power protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the Freecom power parallel port IDE
 	  protocol. If you chose to build PARIDE support into your kernel, you
 	  may answer Y here to build in the protocol driver, otherwise you
 	  should answer M to build it as a loadable module. The module will be
 	  called frpw. You must also have a high-level driver for the type
 	  of device that you want to support.

 config PARIDE_KBIC
 	tristate "KingByte KBIC-951A/971A protocols"
 	depends on PARIDE
 	help
 	  This option enables support for the KBIC-951A and KBIC-971A parallel
 	  port IDE protocols from KingByte Information Corp. KingByte's
 	  adapters appear in many no-name portable disk and CD-ROM products,
 	  especially in Europe. If you chose to build PARIDE support into your
 	  kernel, you may answer Y here to build in the protocol driver,
 	  otherwise you should answer M to build it as a loadable module. The
 	  module will be called kbic. You must also have a high-level driver
 	  for the type of device that you want to support.

 config PARIDE_KTTI
 	tristate "KT PHd protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the "PHd" parallel port IDE protocol
 	  from KT Technology. This is a simple (low speed) adapter that is
 	  used in some 2.5" portable hard drives. If you chose to build PARIDE
 	  support into your kernel, you may answer Y here to build in the
 	  protocol driver, otherwise you should answer M to build it as a
 	  loadable module. The module will be called ktti. You must also
 	  have a high-level driver for the type of device that you want to
 	  support.

 config PARIDE_ON20
 	tristate "OnSpec 90c20 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the (obsolete) 90c20 parallel port
 	  IDE protocol from OnSpec (often marketed under the ValuStore brand
 	  name). If you chose to build PARIDE support into your kernel, you
 	  may answer Y here to build in the protocol driver, otherwise you
 	  should answer M to build it as a loadable module. The module will
 	  be called on20. You must also have a high-level driver for the
 	  type of device that you want to support.

 config PARIDE_ON26
 	tristate "OnSpec 90c26 protocol"
 	depends on PARIDE
 	help
 	  This option enables support for the 90c26 parallel port IDE protocol
 	  from OnSpec Electronics (often marketed under the ValuStore brand
 	  name). If you chose to build PARIDE support into your kernel, you
 	  may answer Y here to build in the protocol driver, otherwise you
 	  should answer M to build it as a loadable module. The module will be
 	  called on26. You must also have a high-level driver for the type
 	  of device that you want to support.

 #
	#
	# PARIDE configuration
	#
	# PARIDE doesn't need PARPORT, but if PARPORT is configured as a module,
	# PARIDE must also be a module. The bogus CONFIG_PARIDE_PARPORT option
	# controls the choices given to the user ...
	# PARIDE only supports PC style parports. Tough for USB or other parports...
	config PARIDE_PARPORT
	tristate
	depends on PARIDE!=n
	default m if PARPORT_PC=m
	default y if PARPORT_PC!=m

	comment "Parallel IDE high-level drivers"
	depends on PARIDE

	config PARIDE_PD
	tristate "Parallel port IDE disks"
	depends on PARIDE
	help
	This option enables the high-level driver for IDE-type disk devices
	connected through a parallel port. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	parallel port IDE driver, otherwise you should answer M to build
	it as a loadable module. The module will be called pd. You
	must also have at least one parallel port protocol driver in your
	system. Among the devices supported by this driver are the SyQuest
	EZ-135, EZ-230 and SparQ drives, the Avatar Shark and the backpack
	hard drives from MicroSolutions.

	config PARIDE_PCD
	tristate "Parallel port ATAPI CD-ROMs"
	depends on PARIDE
	---help---
	This option enables the high-level driver for ATAPI CD-ROM devices
	connected through a parallel port. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	parallel port ATAPI CD-ROM driver, otherwise you should answer M to
	build it as a loadable module. The module will be called pcd. You
	must also have at least one parallel port protocol driver in your
	system. Among the devices supported by this driver are the
	MicroSolutions backpack CD-ROM drives and the Freecom Power CD. If
	you have such a CD-ROM drive, you should also say Y or M to "ISO
	9660 CD-ROM file system support" below, because that's the file
	system used on CD-ROMs.

	config PARIDE_PF
	tristate "Parallel port ATAPI disks"
	depends on PARIDE
	help
	This option enables the high-level driver for ATAPI disk devices
	connected through a parallel port. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	parallel port ATAPI disk driver, otherwise you should answer M
	to build it as a loadable module. The module will be called pf.
	You must also have at least one parallel port protocol driver in
	your system. Among the devices supported by this driver are the
	MicroSolutions backpack PD/CD drive and the Imation Superdisk
	LS-120 drive.

	config PARIDE_PT
	tristate "Parallel port ATAPI tapes"
	depends on PARIDE
	help
	This option enables the high-level driver for ATAPI tape devices
	connected through a parallel port. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	parallel port ATAPI disk driver, otherwise you should answer M
	to build it as a loadable module. The module will be called pt.
	You must also have at least one parallel port protocol driver in
	your system. Among the devices supported by this driver is the
	parallel port version of the HP 5GB drive.

	config PARIDE_PG
	tristate "Parallel port generic ATAPI devices"
	depends on PARIDE
	---help---
	This option enables a special high-level driver for generic ATAPI
	devices connected through a parallel port. The driver allows user
	programs, such as cdrtools, to send ATAPI commands directly to a
	device.

	If you chose to build PARIDE support into your kernel, you may
	answer Y here to build in the parallel port generic ATAPI driver,
	otherwise you should answer M to build it as a loadable module. The
	module will be called pg.

	You must also have at least one parallel port protocol driver in
	your system.

	This driver implements an API loosely related to the generic SCSI
	driver. See <file:include/linux/pg.h>. for details.

	You can obtain the most recent version of cdrtools from
	<ftp://ftp.berlios.de/pub/cdrecord/>. Versions 1.6.1a3 and
	later fully support this driver.

	comment "Parallel IDE protocol modules"
	depends on PARIDE

	config PARIDE_ATEN
	tristate "ATEN EH-100 protocol"
	depends on PARIDE
	help
	This option enables support for the ATEN EH-100 parallel port IDE
	protocol. This protocol is used in some inexpensive low performance
	parallel port kits made in Hong Kong. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	protocol driver, otherwise you should answer M to build it as a
	loadable module. The module will be called aten. You must also
	have a high-level driver for the type of device that you want to
	support.

	config PARIDE_BPCK
	tristate "MicroSolutions backpack (Series 5) protocol"
	depends on PARIDE
	---help---
	This option enables support for the Micro Solutions BACKPACK
	parallel port Series 5 IDE protocol. (Most BACKPACK drives made
	before 1999 were Series 5) Series 5 drives will NOT always have the
	Series noted on the bottom of the drive. Series 6 drivers will.

	In other words, if your BACKPACK drive doesn't say "Series 6" on the
	bottom, enable this option.

	If you chose to build PARIDE support into your kernel, you may
	answer Y here to build in the protocol driver, otherwise you should
	answer M to build it as a loadable module. The module will be
	called bpck. You must also have a high-level driver for the type
	of device that you want to support.

	config PARIDE_BPCK6
	tristate "MicroSolutions backpack (Series 6) protocol"
	depends on PARIDE && !64BIT
	---help---
	This option enables support for the Micro Solutions BACKPACK
	parallel port Series 6 IDE protocol. (Most BACKPACK drives made
	after 1999 were Series 6) Series 6 drives will have the Series noted
	on the bottom of the drive. Series 5 drivers don't always have it
	noted.

	In other words, if your BACKPACK drive says "Series 6" on the
	bottom, enable this option.

	If you chose to build PARIDE support into your kernel, you may
	answer Y here to build in the protocol driver, otherwise you should
	answer M to build it as a loadable module. The module will be
	called bpck6. You must also have a high-level driver for the type
	of device that you want to support.

	config PARIDE_COMM
	tristate "DataStor Commuter protocol"
	depends on PARIDE
	help
	This option enables support for the Commuter parallel port IDE
	protocol from DataStor. If you chose to build PARIDE support
	into your kernel, you may answer Y here to build in the protocol
	driver, otherwise you should answer M to build it as a loadable
	module. The module will be called comm. You must also have
	a high-level driver for the type of device that you want to support.

	config PARIDE_DSTR
	tristate "DataStor EP-2000 protocol"
	depends on PARIDE
	help
	This option enables support for the EP-2000 parallel port IDE
	protocol from DataStor. If you chose to build PARIDE support
	into your kernel, you may answer Y here to build in the protocol
	driver, otherwise you should answer M to build it as a loadable
	module. The module will be called dstr. You must also have
	a high-level driver for the type of device that you want to support.

	config PARIDE_FIT2
	tristate "FIT TD-2000 protocol"
	depends on PARIDE
	help
	This option enables support for the TD-2000 parallel port IDE
	protocol from Fidelity International Technology. This is a simple
	(low speed) adapter that is used in some portable hard drives. If
	you chose to build PARIDE support into your kernel, you may answer Y
	here to build in the protocol driver, otherwise you should answer M
	to build it as a loadable module. The module will be called ktti.
	You must also have a high-level driver for the type of device that
	you want to support.

	config PARIDE_FIT3
	tristate "FIT TD-3000 protocol"
	depends on PARIDE
	help
	This option enables support for the TD-3000 parallel port IDE
	protocol from Fidelity International Technology. This protocol is
	used in newer models of their portable disk, CD-ROM and PD/CD
	devices. If you chose to build PARIDE support into your kernel, you
	may answer Y here to build in the protocol driver, otherwise you
	should answer M to build it as a loadable module. The module will be
	called fit3. You must also have a high-level driver for the type
	of device that you want to support.

	config PARIDE_EPAT
	tristate "Shuttle EPAT/EPEZ protocol"
	depends on PARIDE
	help
	This option enables support for the EPAT parallel port IDE protocol.
	EPAT is a parallel port IDE adapter manufactured by Shuttle
	Technology and widely used in devices from major vendors such as
	Hewlett-Packard, SyQuest, Imation and Avatar. If you chose to build
	PARIDE support into your kernel, you may answer Y here to build in
	the protocol driver, otherwise you should answer M to build it as a
	loadable module. The module will be called epat. You must also
	have a high-level driver for the type of device that you want to
	support.

	config PARIDE_EPATC8
	bool "Support c7/c8 chips (EXPERIMENTAL)"
	depends on PARIDE_EPAT && EXPERIMENTAL
	help
	This option enables support for the newer Shuttle EP1284 (aka c7 and
	c8) chip. You need this if you are using any recent Imation SuperDisk
	(LS-120) drive.

	config PARIDE_EPIA
	tristate "Shuttle EPIA protocol"
	depends on PARIDE
	help
	This option enables support for the (obsolete) EPIA parallel port
	IDE protocol from Shuttle Technology. This adapter can still be
	found in some no-name kits. If you chose to build PARIDE support
	into your kernel, you may answer Y here to build in the protocol
	driver, otherwise you should answer M to build it as a loadable
	module. The module will be called epia. You must also have a
	high-level driver for the type of device that you want to support.

	config PARIDE_FRIQ
	tristate "Freecom IQ ASIC-2 protocol"
	depends on PARIDE
	help
	This option enables support for version 2 of the Freecom IQ parallel
	port IDE adapter. This adapter is used by the Maxell Superdisk
	drive. If you chose to build PARIDE support into your kernel, you
	may answer Y here to build in the protocol driver, otherwise you
	should answer M to build it as a loadable module. The module will be
	called friq. You must also have a high-level driver for the type
	of device that you want to support.

	config PARIDE_FRPW
	tristate "FreeCom power protocol"
	depends on PARIDE
	help
	This option enables support for the Freecom power parallel port IDE
	protocol. If you chose to build PARIDE support into your kernel, you
	may answer Y here to build in the protocol driver, otherwise you
	should answer M to build it as a loadable module. The module will be
	called frpw. You must also have a high-level driver for the type
	of device that you want to support.

	config PARIDE_KBIC
	tristate "KingByte KBIC-951A/971A protocols"
	depends on PARIDE
	help
	This option enables support for the KBIC-951A and KBIC-971A parallel
	port IDE protocols from KingByte Information Corp. KingByte's
	adapters appear in many no-name portable disk and CD-ROM products,
	especially in Europe. If you chose to build PARIDE support into your
	kernel, you may answer Y here to build in the protocol driver,
	otherwise you should answer M to build it as a loadable module. The
	module will be called kbic. You must also have a high-level driver
	for the type of device that you want to support.

	config PARIDE_KTTI
	tristate "KT PHd protocol"
	depends on PARIDE
	help
	This option enables support for the "PHd" parallel port IDE protocol
	from KT Technology. This is a simple (low speed) adapter that is
	used in some 2.5" portable hard drives. If you chose to build PARIDE
	support into your kernel, you may answer Y here to build in the
	protocol driver, otherwise you should answer M to build it as a
	loadable module. The module will be called ktti. You must also
	have a high-level driver for the type of device that you want to
	support.

	config PARIDE_ON20
	tristate "OnSpec 90c20 protocol"
	depends on PARIDE
	help
	This option enables support for the (obsolete) 90c20 parallel port
	IDE protocol from OnSpec (often marketed under the ValuStore brand
	name). If you chose to build PARIDE support into your kernel, you
	may answer Y here to build in the protocol driver, otherwise you
	should answer M to build it as a loadable module. The module will
	be called on20. You must also have a high-level driver for the
	type of device that you want to support.

	config PARIDE_ON26
	tristate "OnSpec 90c26 protocol"
	depends on PARIDE
	help
	This option enables support for the 90c26 parallel port IDE protocol
	from OnSpec Electronics (often marketed under the ValuStore brand
	name). If you chose to build PARIDE support into your kernel, you
	may answer Y here to build in the protocol driver, otherwise you
	should answer M to build it as a loadable module. The module will be
	called on26. You must also have a high-level driver for the type
	of device that you want to support.

	#