blob: f344b9e49198829617c9c3462f068595a1e0794f [file] [log] [blame]
Qualcomm Technologies Inc. adreno/snapdragon DSI output
DSI Controller:
Required properties:
- compatible:
* "qcom,mdss-dsi-ctrl"
- reg: Physical base address and length of the registers of controller
- reg-names: The names of register regions. The following regions are required:
* "dsi_ctrl"
- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should
be 0 or 1, since we have 2 DSI controllers at most for now.
- interrupts: The interrupt signal from the DSI block.
- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
- clock-names: the following clocks are required:
* "bus_clk"
* "byte_clk"
* "core_clk"
* "core_mmss_clk"
* "iface_clk"
* "mdp_core_clk"
* "pixel_clk"
- vdd-supply: phandle to vdd regulator device node
- vddio-supply: phandle to vdd-io regulator device node
- vdda-supply: phandle to vdda regulator device node
- qcom,dsi-phy: phandle to DSI PHY device node
Optional properties:
- panel@0: Node of panel connected to this DSI controller.
See files in Documentation/devicetree/bindings/display/panel/ for each supported
panel.
- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
driving a panel which needs 2 DSI links.
- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
the master link of the 2-DSI panel.
- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
driving a 2-DSI panel whose 2 links need receive command simultaneously.
- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
through MDP block
- pinctrl-names: the pin control state names; should contain "default"
- pinctrl-0: the default pinctrl state (active)
- pinctrl-n: the "sleep" pinctrl state
- port: DSI controller output port. This contains one endpoint subnode, with its
remote-endpoint set to the phandle of the connected panel's endpoint.
See Documentation/devicetree/bindings/graph.txt for device graph info.
DSI PHY:
Required properties:
- compatible: Could be the following
* "qcom,dsi-phy-28nm-hpm"
* "qcom,dsi-phy-28nm-lp"
* "qcom,dsi-phy-20nm"
- reg: Physical base address and length of the registers of PLL, PHY and PHY
regulator
- reg-names: The names of register regions. The following regions are required:
* "dsi_pll"
* "dsi_phy"
* "dsi_phy_regulator"
- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should
be 0 or 1, since we have 2 DSI PHYs at most for now.
- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
- clock-names: the following clocks are required:
* "iface_clk"
- vddio-supply: phandle to vdd-io regulator device node
Optional properties:
- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
regulator is wanted.
Example:
mdss_dsi0: qcom,mdss_dsi@fd922800 {
compatible = "qcom,mdss-dsi-ctrl";
qcom,dsi-host-index = <0>;
interrupt-parent = <&mdss_mdp>;
interrupts = <4 0>;
reg-names = "dsi_ctrl";
reg = <0xfd922800 0x200>;
power-domains = <&mmcc MDSS_GDSC>;
clock-names =
"bus_clk",
"byte_clk",
"core_clk",
"core_mmss_clk",
"iface_clk",
"mdp_core_clk",
"pixel_clk";
clocks =
<&mmcc MDSS_AXI_CLK>,
<&mmcc MDSS_BYTE0_CLK>,
<&mmcc MDSS_ESC0_CLK>,
<&mmcc MMSS_MISC_AHB_CLK>,
<&mmcc MDSS_AHB_CLK>,
<&mmcc MDSS_MDP_CLK>,
<&mmcc MDSS_PCLK0_CLK>;
vdda-supply = <&pma8084_l2>;
vdd-supply = <&pma8084_l22>;
vddio-supply = <&pma8084_l12>;
qcom,dsi-phy = <&mdss_dsi_phy0>;
qcom,dual-dsi-mode;
qcom,master-dsi;
qcom,sync-dual-dsi;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&mdss_dsi_active>;
pinctrl-1 = <&mdss_dsi_suspend>;
panel: panel@0 {
compatible = "sharp,lq101r1sx01";
reg = <0>;
link2 = <&secondary>;
power-supply = <...>;
backlight = <...>;
port {
panel_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
};
port {
dsi0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 {
compatible = "qcom,dsi-phy-28nm-hpm";
qcom,dsi-phy-index = <0>;
reg-names =
"dsi_pll",
"dsi_phy",
"dsi_phy_regulator";
reg = <0xfd922a00 0xd4>,
<0xfd922b00 0x2b0>,
<0xfd922d80 0x7b>;
clock-names = "iface_clk";
clocks = <&mmcc MDSS_AHB_CLK>;
vddio-supply = <&pma8084_l12>;
qcom,dsi-phy-regulator-ldo-mode;
};