blob: 65379ed8ed35f10c36c22eb3f8a6054e23fd4302 [file] [log] [blame]
/* Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/debugfs.h>
#include <linux/kernel.h>
#include <linux/regmap.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/spmi.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/interrupt.h>
#include <linux/list.h>
#include <linux/mutex.h>
#include <linux/input.h>
#include <linux/log2.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/of_regulator.h>
#include <linux/input/qpnp-power-on.h>
#include <linux/qpnp/qpnp-pbs.h>
#include <linux/qpnp/qpnp-misc.h>
#include <linux/power_supply.h>
#define PMIC_VER_8941 0x01
#define PMIC_VERSION_REG 0x0105
#define PMIC_VERSION_REV4_REG 0x0103
#define PMIC8941_V1_REV4 0x01
#define PMIC8941_V2_REV4 0x02
#define PON_PRIMARY 0x01
#define PON_SECONDARY 0x02
#define PON_1REG 0x03
#define PON_GEN2_PRIMARY 0x04
#define PON_GEN2_SECONDARY 0x05
#define PON_OFFSET(subtype, offset_gen1, offset_gen2) \
(((subtype == PON_PRIMARY) || \
(subtype == PON_SECONDARY) || \
(subtype == PON_1REG)) ? offset_gen1 : offset_gen2)
/* Common PNP defines */
#define QPNP_PON_REVISION2(pon) ((pon)->base + 0x01)
#define QPNP_PON_PERPH_SUBTYPE(pon) ((pon)->base + 0x05)
/* PON common register addresses */
#define QPNP_PON_RT_STS(pon) ((pon)->base + 0x10)
#define QPNP_PON_PULL_CTL(pon) ((pon)->base + 0x70)
#define QPNP_PON_DBC_CTL(pon) ((pon)->base + 0x71)
/* PON/RESET sources register addresses */
#define QPNP_PON_REASON1(pon) \
((pon)->base + PON_OFFSET((pon)->subtype, 0x8, 0xC0))
#define QPNP_PON_WARM_RESET_REASON1(pon) \
((pon)->base + PON_OFFSET((pon)->subtype, 0xA, 0xC2))
#define QPNP_POFF_REASON1(pon) \
((pon)->base + PON_OFFSET((pon)->subtype, 0xC, 0xC5))
#define QPNP_PON_WARM_RESET_REASON2(pon) ((pon)->base + 0xB)
#define QPNP_PON_OFF_REASON(pon) ((pon)->base + 0xC7)
#define QPNP_FAULT_REASON1(pon) ((pon)->base + 0xC8)
#define QPNP_S3_RESET_REASON(pon) ((pon)->base + 0xCA)
#define QPNP_PON_KPDPWR_S1_TIMER(pon) ((pon)->base + 0x40)
#define QPNP_PON_KPDPWR_S2_TIMER(pon) ((pon)->base + 0x41)
#define QPNP_PON_KPDPWR_S2_CNTL(pon) ((pon)->base + 0x42)
#define QPNP_PON_KPDPWR_S2_CNTL2(pon) ((pon)->base + 0x43)
#define QPNP_PON_RESIN_S1_TIMER(pon) ((pon)->base + 0x44)
#define QPNP_PON_RESIN_S2_TIMER(pon) ((pon)->base + 0x45)
#define QPNP_PON_RESIN_S2_CNTL(pon) ((pon)->base + 0x46)
#define QPNP_PON_RESIN_S2_CNTL2(pon) ((pon)->base + 0x47)
#define QPNP_PON_KPDPWR_RESIN_S1_TIMER(pon) ((pon)->base + 0x48)
#define QPNP_PON_KPDPWR_RESIN_S2_TIMER(pon) ((pon)->base + 0x49)
#define QPNP_PON_KPDPWR_RESIN_S2_CNTL(pon) ((pon)->base + 0x4A)
#define QPNP_PON_KPDPWR_RESIN_S2_CNTL2(pon) ((pon)->base + 0x4B)
#define QPNP_PON_PS_HOLD_RST_CTL(pon) ((pon)->base + 0x5A)
#define QPNP_PON_PS_HOLD_RST_CTL2(pon) ((pon)->base + 0x5B)
#define QPNP_PON_WD_RST_S2_CTL(pon) ((pon)->base + 0x56)
#define QPNP_PON_WD_RST_S2_CTL2(pon) ((pon)->base + 0x57)
#define QPNP_PON_S3_SRC(pon) ((pon)->base + 0x74)
#define QPNP_PON_S3_DBC_CTL(pon) ((pon)->base + 0x75)
#define QPNP_PON_SMPL_CTL(pon) ((pon)->base + 0x7F)
#define QPNP_PON_TRIGGER_EN(pon) ((pon)->base + 0x80)
#define QPNP_PON_XVDD_RB_SPARE(pon) ((pon)->base + 0x8E)
#define QPNP_PON_SOFT_RB_SPARE(pon) ((pon)->base + 0x8F)
#define QPNP_PON_SEC_ACCESS(pon) ((pon)->base + 0xD0)
#define QPNP_PON_SEC_UNLOCK 0xA5
#define QPNP_PON_WARM_RESET_TFT BIT(4)
#define QPNP_PON_RESIN_PULL_UP BIT(0)
#define QPNP_PON_KPDPWR_PULL_UP BIT(1)
#define QPNP_PON_CBLPWR_PULL_UP BIT(2)
#define QPNP_PON_FAULT_PULL_UP BIT(4)
#define QPNP_PON_S2_CNTL_EN BIT(7)
#define QPNP_PON_S2_RESET_ENABLE BIT(7)
#define QPNP_PON_DELAY_BIT_SHIFT 6
#define QPNP_PON_GEN2_DELAY_BIT_SHIFT 14
#define QPNP_PON_S1_TIMER_MASK (0xF)
#define QPNP_PON_S2_TIMER_MASK (0x7)
#define QPNP_PON_S2_CNTL_TYPE_MASK (0xF)
#define QPNP_PON_DBC_DELAY_MASK(pon) \
PON_OFFSET((pon)->subtype, 0x7, 0xF)
#define QPNP_PON_KPDPWR_N_SET BIT(0)
#define QPNP_PON_RESIN_N_SET BIT(1)
#define QPNP_PON_CBLPWR_N_SET BIT(2)
#define QPNP_PON_RESIN_BARK_N_SET BIT(4)
#define QPNP_PON_KPDPWR_RESIN_BARK_N_SET BIT(5)
#define QPNP_PON_WD_EN BIT(7)
#define QPNP_PON_RESET_EN BIT(7)
#define QPNP_PON_POWER_OFF_MASK 0xF
#define QPNP_GEN2_POFF_SEQ BIT(7)
#define QPNP_GEN2_FAULT_SEQ BIT(6)
#define QPNP_GEN2_S3_RESET_SEQ BIT(5)
#define QPNP_PON_S3_SRC_KPDPWR 0
#define QPNP_PON_S3_SRC_RESIN 1
#define QPNP_PON_S3_SRC_KPDPWR_AND_RESIN 2
#define QPNP_PON_S3_SRC_KPDPWR_OR_RESIN 3
#define QPNP_PON_S3_SRC_MASK 0x3
#define QPNP_PON_HARD_RESET_MASK GENMASK(7, 5)
#define QPNP_PON_UVLO_DLOAD_EN BIT(7)
#define QPNP_PON_SMPL_EN BIT(7)
/* Ranges */
#define QPNP_PON_S1_TIMER_MAX 10256
#define QPNP_PON_S2_TIMER_MAX 2000
#define QPNP_PON_S3_TIMER_SECS_MAX 128
#define QPNP_PON_S3_DBC_DELAY_MASK 0x07
#define QPNP_PON_RESET_TYPE_MAX 0xF
#define PON_S1_COUNT_MAX 0xF
#define QPNP_PON_MIN_DBC_US (USEC_PER_SEC / 64)
#define QPNP_PON_MAX_DBC_US (USEC_PER_SEC * 2)
#define QPNP_PON_GEN2_MIN_DBC_US 62
#define QPNP_PON_GEN2_MAX_DBC_US (USEC_PER_SEC / 4)
#define QPNP_KEY_STATUS_DELAY msecs_to_jiffies(250)
#define QPNP_PON_BUFFER_SIZE 9
#define QPNP_POFF_REASON_UVLO 13
enum qpnp_pon_version {
QPNP_PON_GEN1_V1,
QPNP_PON_GEN1_V2,
QPNP_PON_GEN2,
};
enum pon_type {
PON_KPDPWR,
PON_RESIN,
PON_CBLPWR,
PON_KPDPWR_RESIN,
};
struct qpnp_pon_config {
u32 pon_type;
u32 support_reset;
u32 key_code;
u32 s1_timer;
u32 s2_timer;
u32 s2_type;
u32 pull_up;
u32 state_irq;
u32 bark_irq;
u16 s2_cntl_addr;
u16 s2_cntl2_addr;
bool old_state;
bool use_bark;
bool config_reset;
};
struct pon_regulator {
struct qpnp_pon *pon;
struct regulator_dev *rdev;
struct regulator_desc rdesc;
u32 addr;
u32 bit;
bool enabled;
};
struct qpnp_pon {
struct platform_device *pdev;
struct regmap *regmap;
struct input_dev *pon_input;
struct qpnp_pon_config *pon_cfg;
struct pon_regulator *pon_reg_cfg;
struct list_head list;
struct delayed_work bark_work;
struct dentry *debugfs;
struct device_node *pbs_dev_node;
int pon_trigger_reason;
int pon_power_off_reason;
int num_pon_reg;
int num_pon_config;
u32 dbc_time_us;
u32 uvlo;
int warm_reset_poff_type;
int hard_reset_poff_type;
int shutdown_poff_type;
int resin_warm_reset_type;
int resin_hard_reset_type;
int resin_shutdown_type;
u16 base;
u8 subtype;
u8 pon_ver;
u8 warm_reset_reason1;
u8 warm_reset_reason2;
u8 twm_state;
bool is_spon;
bool store_hard_reset_reason;
bool resin_hard_reset_disable;
bool resin_shutdown_disable;
bool ps_hold_hard_reset_disable;
bool ps_hold_shutdown_disable;
bool kpdpwr_dbc_enable;
bool support_twm_config;
bool resin_pon_reset;
ktime_t kpdpwr_last_release_time;
struct notifier_block pon_nb;
bool legacy_hard_reset_offset;
};
static int pon_ship_mode_en;
module_param_named(
ship_mode_en, pon_ship_mode_en, int, 0600
);
static struct qpnp_pon *sys_reset_dev;
static DEFINE_SPINLOCK(spon_list_slock);
static LIST_HEAD(spon_dev_list);
static u32 s1_delay[PON_S1_COUNT_MAX + 1] = {
0, 32, 56, 80, 138, 184, 272, 408, 608, 904, 1352, 2048,
3072, 4480, 6720, 10256
};
static const char * const qpnp_pon_reason[] = {
[0] = "Triggered from Hard Reset",
[1] = "Triggered from SMPL (sudden momentary power loss)",
[2] = "Triggered from RTC (RTC alarm expiry)",
[3] = "Triggered from DC (DC charger insertion)",
[4] = "Triggered from USB (USB charger insertion)",
[5] = "Triggered from PON1 (secondary PMIC)",
[6] = "Triggered from CBL (external power supply)",
[7] = "Triggered from KPD (power key press)",
};
#define POFF_REASON_FAULT_OFFSET 16
#define POFF_REASON_S3_RESET_OFFSET 32
static const char * const qpnp_poff_reason[] = {
/* QPNP_PON_GEN1 POFF reasons */
[0] = "Triggered from SOFT (Software)",
[1] = "Triggered from PS_HOLD (PS_HOLD/MSM controlled shutdown)",
[2] = "Triggered from PMIC_WD (PMIC watchdog)",
[3] = "Triggered from GP1 (Keypad_Reset1)",
[4] = "Triggered from GP2 (Keypad_Reset2)",
[5] = "Triggered from KPDPWR_AND_RESIN (Simultaneous power key and reset line)",
[6] = "Triggered from RESIN_N (Reset line/Volume Down Key)",
[7] = "Triggered from KPDPWR_N (Long Power Key hold)",
[8] = "N/A",
[9] = "N/A",
[10] = "N/A",
[11] = "Triggered from CHARGER (Charger ENUM_TIMER, BOOT_DONE)",
[12] = "Triggered from TFT (Thermal Fault Tolerance)",
[13] = "Triggered from UVLO (Under Voltage Lock Out)",
[14] = "Triggered from OTST3 (Overtemp)",
[15] = "Triggered from STAGE3 (Stage 3 reset)",
/* QPNP_PON_GEN2 FAULT reasons */
[16] = "Triggered from GP_FAULT0",
[17] = "Triggered from GP_FAULT1",
[18] = "Triggered from GP_FAULT2",
[19] = "Triggered from GP_FAULT3",
[20] = "Triggered from MBG_FAULT",
[21] = "Triggered from OVLO (Over Voltage Lock Out)",
[22] = "Triggered from UVLO (Under Voltage Lock Out)",
[23] = "Triggered from AVDD_RB",
[24] = "N/A",
[25] = "N/A",
[26] = "N/A",
[27] = "Triggered from FAULT_FAULT_N",
[28] = "Triggered from FAULT_PBS_WATCHDOG_TO",
[29] = "Triggered from FAULT_PBS_NACK",
[30] = "Triggered from FAULT_RESTART_PON",
[31] = "Triggered from OTST3 (Overtemp)",
/* QPNP_PON_GEN2 S3_RESET reasons */
[32] = "N/A",
[33] = "N/A",
[34] = "N/A",
[35] = "N/A",
[36] = "Triggered from S3_RESET_FAULT_N",
[37] = "Triggered from S3_RESET_PBS_WATCHDOG_TO",
[38] = "Triggered from S3_RESET_PBS_NACK",
[39] = "Triggered from S3_RESET_KPDPWR_ANDOR_RESIN (power key and/or reset line)",
};
static int
qpnp_pon_masked_write(struct qpnp_pon *pon, u16 addr, u8 mask, u8 val)
{
int rc;
rc = regmap_update_bits(pon->regmap, addr, mask, val);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to regmap_update_bits to addr=%hx, rc(%d)\n",
addr, rc);
return rc;
}
static bool is_pon_gen1(struct qpnp_pon *pon)
{
return pon->subtype == PON_PRIMARY ||
pon->subtype == PON_SECONDARY;
}
static bool is_pon_gen2(struct qpnp_pon *pon)
{
return pon->subtype == PON_GEN2_PRIMARY ||
pon->subtype == PON_GEN2_SECONDARY;
}
/**
* qpnp_pon_set_restart_reason - Store device restart reason in PMIC register.
*
* Returns = 0 if PMIC feature is not available or store restart reason
* successfully.
* Returns > 0 for errors
*
* This function is used to store device restart reason in PMIC register.
* It checks here to see if the restart reason register has been specified.
* If it hasn't, this function should immediately return 0
*/
int qpnp_pon_set_restart_reason(enum pon_restart_reason reason)
{
int rc = 0;
struct qpnp_pon *pon = sys_reset_dev;
if (!pon)
return 0;
if (!pon->store_hard_reset_reason)
return 0;
if (is_pon_gen2(pon) && !pon->legacy_hard_reset_offset)
rc = qpnp_pon_masked_write(pon, QPNP_PON_SOFT_RB_SPARE(pon),
GENMASK(7, 1), (reason << 1));
else
rc = qpnp_pon_masked_write(pon, QPNP_PON_SOFT_RB_SPARE(pon),
GENMASK(7, 2), (reason << 2));
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_SOFT_RB_SPARE(pon), rc);
return rc;
}
EXPORT_SYMBOL(qpnp_pon_set_restart_reason);
/*
* qpnp_pon_check_hard_reset_stored - Checks if the PMIC need to
* store hard reset reason.
*
* Returns true if reset reason can be stored, false if it cannot be stored
*
*/
bool qpnp_pon_check_hard_reset_stored(void)
{
struct qpnp_pon *pon = sys_reset_dev;
if (!pon)
return false;
return pon->store_hard_reset_reason;
}
EXPORT_SYMBOL(qpnp_pon_check_hard_reset_stored);
static int qpnp_pon_set_dbc(struct qpnp_pon *pon, u32 delay)
{
int rc = 0;
u32 val;
if (delay == pon->dbc_time_us)
goto out;
if (pon->pon_input)
mutex_lock(&pon->pon_input->mutex);
if (is_pon_gen2(pon)) {
if (delay < QPNP_PON_GEN2_MIN_DBC_US)
delay = QPNP_PON_GEN2_MIN_DBC_US;
else if (delay > QPNP_PON_GEN2_MAX_DBC_US)
delay = QPNP_PON_GEN2_MAX_DBC_US;
val = (delay << QPNP_PON_GEN2_DELAY_BIT_SHIFT) / USEC_PER_SEC;
} else {
if (delay < QPNP_PON_MIN_DBC_US)
delay = QPNP_PON_MIN_DBC_US;
else if (delay > QPNP_PON_MAX_DBC_US)
delay = QPNP_PON_MAX_DBC_US;
val = (delay << QPNP_PON_DELAY_BIT_SHIFT) / USEC_PER_SEC;
}
val = ilog2(val);
rc = qpnp_pon_masked_write(pon, QPNP_PON_DBC_CTL(pon),
QPNP_PON_DBC_DELAY_MASK(pon), val);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to set PON debounce\n");
goto unlock;
}
pon->dbc_time_us = delay;
unlock:
if (pon->pon_input)
mutex_unlock(&pon->pon_input->mutex);
out:
return rc;
}
static int qpnp_pon_get_dbc(struct qpnp_pon *pon, u32 *delay)
{
int rc;
unsigned int val;
rc = regmap_read(pon->regmap, QPNP_PON_DBC_CTL(pon), &val);
if (rc) {
pr_err("Unable to read pon_dbc_ctl rc=%d\n", rc);
return rc;
}
val &= QPNP_PON_DBC_DELAY_MASK(pon);
if (is_pon_gen2(pon))
*delay = USEC_PER_SEC /
(1 << (QPNP_PON_GEN2_DELAY_BIT_SHIFT - val));
else
*delay = USEC_PER_SEC /
(1 << (QPNP_PON_DELAY_BIT_SHIFT - val));
return rc;
}
static ssize_t qpnp_pon_dbc_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct qpnp_pon *pon = dev_get_drvdata(dev);
return snprintf(buf, QPNP_PON_BUFFER_SIZE, "%d\n", pon->dbc_time_us);
}
static ssize_t qpnp_pon_dbc_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t size)
{
struct qpnp_pon *pon = dev_get_drvdata(dev);
u32 value;
int rc;
if (size > QPNP_PON_BUFFER_SIZE)
return -EINVAL;
rc = kstrtou32(buf, 10, &value);
if (rc)
return rc;
rc = qpnp_pon_set_dbc(pon, value);
if (rc < 0)
return rc;
return size;
}
static struct qpnp_pon_config *
qpnp_get_cfg(struct qpnp_pon *pon, u32 pon_type)
{
int i;
for (i = 0; i < pon->num_pon_config; i++) {
if (pon_type == pon->pon_cfg[i].pon_type)
return &pon->pon_cfg[i];
}
return NULL;
}
static DEVICE_ATTR(debounce_us, 0664, qpnp_pon_dbc_show, qpnp_pon_dbc_store);
#define PON_TWM_ENTRY_PBS_BIT BIT(0)
static int qpnp_pon_reset_config(struct qpnp_pon *pon,
enum pon_power_off_type type)
{
int rc;
bool disable = false;
u16 rst_en_reg;
struct qpnp_pon_config *cfg;
/* Ignore the PS_HOLD reset config if TWM ENTRY is enabled */
if (pon->support_twm_config && pon->twm_state == PMIC_TWM_ENABLE) {
rc = qpnp_pbs_trigger_event(pon->pbs_dev_node,
PON_TWM_ENTRY_PBS_BIT);
if (rc < 0) {
pr_err("Unable to trigger PBS trigger for TWM entry rc=%d\n",
rc);
return rc;
}
cfg = qpnp_get_cfg(pon, PON_KPDPWR);
if (cfg) {
/* configure KPDPWR_S2 to Hard reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl_addr,
QPNP_PON_S2_CNTL_TYPE_MASK,
PON_POWER_OFF_HARD_RESET);
if (rc < 0)
pr_err("Unable to config KPDPWR_N S2 for hard-reset rc=%d\n",
rc);
}
pr_crit("PMIC configured for TWM entry\n");
return 0;
}
if (pon->pon_ver == QPNP_PON_GEN1_V1)
rst_en_reg = QPNP_PON_PS_HOLD_RST_CTL(pon);
else
rst_en_reg = QPNP_PON_PS_HOLD_RST_CTL2(pon);
/*
* Based on the poweroff type set for a PON device through device tree
* change the type being configured into PS_HOLD_RST_CTL.
*/
switch (type) {
case PON_POWER_OFF_WARM_RESET:
if (pon->warm_reset_poff_type != -EINVAL)
type = pon->warm_reset_poff_type;
break;
case PON_POWER_OFF_HARD_RESET:
if (pon->hard_reset_poff_type != -EINVAL)
type = pon->hard_reset_poff_type;
disable = pon->ps_hold_hard_reset_disable;
break;
case PON_POWER_OFF_SHUTDOWN:
if (pon->shutdown_poff_type != -EINVAL)
type = pon->shutdown_poff_type;
disable = pon->ps_hold_shutdown_disable;
break;
default:
break;
}
rc = qpnp_pon_masked_write(pon, rst_en_reg, QPNP_PON_RESET_EN, 0);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
rst_en_reg, rc);
/*
* Check if ps-hold power off configuration needs to be disabled.
* If yes, then return without configuring.
*/
if (disable)
return rc;
/*
* We need 10 sleep clock cycles here. But since the clock is
* internally generated, we need to add 50% tolerance to be
* conservative.
*/
udelay(500);
rc = qpnp_pon_masked_write(pon, QPNP_PON_PS_HOLD_RST_CTL(pon),
QPNP_PON_POWER_OFF_MASK, type);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_PS_HOLD_RST_CTL(pon), rc);
rc = qpnp_pon_masked_write(pon, rst_en_reg, QPNP_PON_RESET_EN,
QPNP_PON_RESET_EN);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
rst_en_reg, rc);
dev_dbg(&pon->pdev->dev, "ps_hold power off type = 0x%02X\n", type);
return rc;
}
static int qpnp_resin_pon_reset_config(struct qpnp_pon *pon,
enum pon_power_off_type type)
{
int rc;
bool disable = false;
u16 rst_en_reg;
if (pon->pon_ver == QPNP_PON_GEN1_V1)
rst_en_reg = QPNP_PON_RESIN_S2_CNTL(pon);
else
rst_en_reg = QPNP_PON_RESIN_S2_CNTL2(pon);
/*
* Based on the poweroff type set for a PON device through device tree
* change the type being configured into PON_RESIN_S2_CTL.
*/
switch (type) {
case PON_POWER_OFF_WARM_RESET:
if (pon->resin_warm_reset_type != -EINVAL)
type = pon->resin_warm_reset_type;
break;
case PON_POWER_OFF_HARD_RESET:
if (pon->resin_hard_reset_type != -EINVAL)
type = pon->resin_hard_reset_type;
disable = pon->resin_hard_reset_disable;
break;
case PON_POWER_OFF_SHUTDOWN:
if (pon->resin_shutdown_type != -EINVAL)
type = pon->resin_shutdown_type;
disable = pon->resin_shutdown_disable;
break;
default:
break;
}
rc = qpnp_pon_masked_write(pon, rst_en_reg, QPNP_PON_S2_CNTL_EN, 0);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
rst_en_reg, rc);
/*
* Check if resin power off configuration needs to be disabled.
* If yes, then return without configuring.
*/
if (disable)
return rc;
/*
* We need 10 sleep clock cycles here. But since the clock is
* internally generated, we need to add 50% tolerance to be
* conservative.
*/
udelay(500);
rc = qpnp_pon_masked_write(pon, QPNP_PON_RESIN_S2_CNTL(pon),
QPNP_PON_S2_CNTL_TYPE_MASK, type);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_RESIN_S2_CNTL(pon), rc);
rc = qpnp_pon_masked_write(pon, rst_en_reg, QPNP_PON_S2_CNTL_EN,
QPNP_PON_S2_CNTL_EN);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
rst_en_reg, rc);
dev_dbg(&pon->pdev->dev, "resin power off type = 0x%02X\n", type);
return rc;
}
/**
* qpnp_pon_system_pwr_off - Configure system-reset PMIC for shutdown or reset
* @type: Determines the type of power off to perform - shutdown, reset, etc
*
* This function will support configuring for multiple PMICs. In some cases, the
* PON of secondary PMICs also needs to be configured. So this supports that
* requirement. Once the system-reset and secondary PMIC is configured properly,
* the MSM can drop PS_HOLD to activate the specified configuration. Note that
* this function may be called from atomic context as in the case of the panic
* notifier path and thus it should not rely on function calls that may sleep.
*/
int qpnp_pon_system_pwr_off(enum pon_power_off_type type)
{
int rc = 0;
struct qpnp_pon *pon = sys_reset_dev;
struct qpnp_pon *tmp;
struct power_supply *batt_psy;
union power_supply_propval val;
unsigned long flags;
if (!pon)
return -ENODEV;
rc = qpnp_pon_reset_config(pon, type);
if (rc) {
dev_err(&pon->pdev->dev,
"Error configuring main PON rc: %d\n",
rc);
return rc;
}
/*
* Check if a secondary PON device needs to be configured. If it
* is available, configure that also as per the requested power off
* type
*/
spin_lock_irqsave(&spon_list_slock, flags);
if (list_empty(&spon_dev_list))
goto out;
list_for_each_entry_safe(pon, tmp, &spon_dev_list, list) {
dev_emerg(&pon->pdev->dev,
"PMIC@SID%d: configuring PON for reset\n",
to_spmi_device(pon->pdev->dev.parent)->usid);
rc = qpnp_pon_reset_config(pon, type);
if (rc) {
dev_err(&pon->pdev->dev,
"Error configuring secondary PON rc: %d\n",
rc);
goto out;
}
if (pon->resin_pon_reset) {
rc = qpnp_resin_pon_reset_config(pon, type);
if (rc) {
dev_err(&pon->pdev->dev,
"Error configuring secondary PON resin rc: %d\n",
rc);
goto out;
}
}
}
/* Set ship mode here if it has been requested */
if (!!pon_ship_mode_en) {
batt_psy = power_supply_get_by_name("battery");
if (batt_psy) {
pr_debug("Set ship mode!\n");
val.intval = 1;
rc = power_supply_set_property(batt_psy,
POWER_SUPPLY_PROP_SET_SHIP_MODE, &val);
if (rc)
dev_err(&pon->pdev->dev,
"Set ship-mode failed\n");
}
}
out:
spin_unlock_irqrestore(&spon_list_slock, flags);
return rc;
}
EXPORT_SYMBOL(qpnp_pon_system_pwr_off);
/**
* qpnp_pon_is_warm_reset - Checks if the PMIC went through a warm reset.
*
* Returns > 0 for warm resets, 0 for not warm reset, < 0 for errors
*
* Note that this function will only return the warm vs not-warm reset status
* of the PMIC that is configured as the system-reset device.
*/
int qpnp_pon_is_warm_reset(void)
{
struct qpnp_pon *pon = sys_reset_dev;
if (!pon)
return -EPROBE_DEFER;
if (is_pon_gen1(pon) || pon->subtype == PON_1REG)
return pon->warm_reset_reason1
|| (pon->warm_reset_reason2 & QPNP_PON_WARM_RESET_TFT);
else
return pon->warm_reset_reason1;
}
EXPORT_SYMBOL(qpnp_pon_is_warm_reset);
/**
* qpnp_pon_wd_config - Disable the wd in a warm reset.
* @enable: to enable or disable the PON watch dog
*
* Returns = 0 for operate successfully, < 0 for errors
*/
int qpnp_pon_wd_config(bool enable)
{
struct qpnp_pon *pon = sys_reset_dev;
int rc = 0;
if (!pon)
return -EPROBE_DEFER;
rc = qpnp_pon_masked_write(pon, QPNP_PON_WD_RST_S2_CTL2(pon),
QPNP_PON_WD_EN, enable ? QPNP_PON_WD_EN : 0);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_WD_RST_S2_CTL2(pon), rc);
return rc;
}
EXPORT_SYMBOL(qpnp_pon_wd_config);
static int qpnp_pon_get_trigger_config(enum pon_trigger_source pon_src,
bool *enabled)
{
struct qpnp_pon *pon = sys_reset_dev;
int rc;
u16 addr;
int val;
u8 mask;
if (!pon)
return -ENODEV;
if (pon_src < PON_SMPL || pon_src > PON_KPDPWR_N) {
dev_err(&pon->pdev->dev, "Invalid PON source\n");
return -EINVAL;
}
addr = QPNP_PON_TRIGGER_EN(pon);
mask = BIT(pon_src);
if (is_pon_gen2(pon) && pon_src == PON_SMPL) {
addr = QPNP_PON_SMPL_CTL(pon);
mask = QPNP_PON_SMPL_EN;
}
rc = regmap_read(pon->regmap, addr, &val);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to read from addr=%hx, rc(%d)\n",
addr, rc);
else
*enabled = !!(val & mask);
return rc;
}
/**
* qpnp_pon_trigger_config - Configures (enable/disable) the PON trigger source
* @pon_src: PON source to be configured
* @enable: to enable or disable the PON trigger
*
* This function configures the power-on trigger capability of a
* PON source. If a specific PON trigger is disabled it cannot act
* as a power-on source to the PMIC.
*/
int qpnp_pon_trigger_config(enum pon_trigger_source pon_src, bool enable)
{
struct qpnp_pon *pon = sys_reset_dev;
int rc;
if (!pon)
return -EPROBE_DEFER;
if (pon_src < PON_SMPL || pon_src > PON_KPDPWR_N) {
dev_err(&pon->pdev->dev, "Invalid PON source\n");
return -EINVAL;
}
if (is_pon_gen2(pon) && pon_src == PON_SMPL) {
rc = qpnp_pon_masked_write(pon, QPNP_PON_SMPL_CTL(pon),
QPNP_PON_SMPL_EN, enable ? QPNP_PON_SMPL_EN : 0);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_SMPL_CTL(pon), rc);
} else {
rc = qpnp_pon_masked_write(pon, QPNP_PON_TRIGGER_EN(pon),
BIT(pon_src), enable ? BIT(pon_src) : 0);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%x, rc(%d)\n",
QPNP_PON_TRIGGER_EN(pon), rc);
}
return rc;
}
EXPORT_SYMBOL(qpnp_pon_trigger_config);
/*
* This function stores the PMIC warm reset reason register values. It also
* clears these registers if the qcom,clear-warm-reset device tree property
* is specified.
*/
static int qpnp_pon_store_and_clear_warm_reset(struct qpnp_pon *pon)
{
int rc;
u8 reg = 0;
uint val;
rc = regmap_read(pon->regmap, QPNP_PON_WARM_RESET_REASON1(pon),
&val);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read addr=%x, rc(%d)\n",
QPNP_PON_WARM_RESET_REASON1(pon), rc);
return rc;
}
pon->warm_reset_reason1 = (u8)val;
if (is_pon_gen1(pon) || pon->subtype == PON_1REG) {
rc = regmap_read(pon->regmap, QPNP_PON_WARM_RESET_REASON2(pon),
&val);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read addr=%x, rc(%d)\n",
QPNP_PON_WARM_RESET_REASON2(pon), rc);
return rc;
}
pon->warm_reset_reason2 = (u8)val;
}
if (of_property_read_bool(pon->pdev->dev.of_node,
"qcom,clear-warm-reset")) {
rc = regmap_write(pon->regmap,
QPNP_PON_WARM_RESET_REASON1(pon), reg);
if (rc)
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
QPNP_PON_WARM_RESET_REASON1(pon), rc);
}
return 0;
}
static int
qpnp_pon_input_dispatch(struct qpnp_pon *pon, u32 pon_type)
{
int rc;
struct qpnp_pon_config *cfg = NULL;
u8 pon_rt_bit = 0;
u32 key_status;
uint pon_rt_sts;
u64 elapsed_us;
cfg = qpnp_get_cfg(pon, pon_type);
if (!cfg)
return -EINVAL;
/* Check if key reporting is supported */
if (!cfg->key_code)
return 0;
if (pon->kpdpwr_dbc_enable && cfg->pon_type == PON_KPDPWR) {
elapsed_us = ktime_us_delta(ktime_get(),
pon->kpdpwr_last_release_time);
if (elapsed_us < pon->dbc_time_us) {
pr_debug("Ignoring kpdpwr event - within debounce time\n");
return 0;
}
}
/* check the RT status to get the current status of the line */
rc = regmap_read(pon->regmap, QPNP_PON_RT_STS(pon), &pon_rt_sts);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read PON RT status\n");
return rc;
}
switch (cfg->pon_type) {
case PON_KPDPWR:
pon_rt_bit = QPNP_PON_KPDPWR_N_SET;
break;
case PON_RESIN:
pon_rt_bit = QPNP_PON_RESIN_N_SET;
break;
case PON_CBLPWR:
pon_rt_bit = QPNP_PON_CBLPWR_N_SET;
break;
case PON_KPDPWR_RESIN:
pon_rt_bit = QPNP_PON_KPDPWR_RESIN_BARK_N_SET;
break;
default:
return -EINVAL;
}
pr_debug("PMIC input: code=%d, sts=0x%hhx\n",
cfg->key_code, pon_rt_sts);
key_status = pon_rt_sts & pon_rt_bit;
if (pon->kpdpwr_dbc_enable && cfg->pon_type == PON_KPDPWR) {
if (!key_status)
pon->kpdpwr_last_release_time = ktime_get();
}
/*
* simulate press event in case release event occurred
* without a press event
*/
if (!cfg->old_state && !key_status) {
input_report_key(pon->pon_input, cfg->key_code, 1);
input_sync(pon->pon_input);
}
input_report_key(pon->pon_input, cfg->key_code, key_status);
input_sync(pon->pon_input);
cfg->old_state = !!key_status;
return 0;
}
static irqreturn_t qpnp_kpdpwr_irq(int irq, void *_pon)
{
int rc;
struct qpnp_pon *pon = _pon;
rc = qpnp_pon_input_dispatch(pon, PON_KPDPWR);
if (rc)
dev_err(&pon->pdev->dev, "Unable to send input event\n");
return IRQ_HANDLED;
}
static irqreturn_t qpnp_kpdpwr_bark_irq(int irq, void *_pon)
{
return IRQ_HANDLED;
}
static irqreturn_t qpnp_resin_irq(int irq, void *_pon)
{
int rc;
struct qpnp_pon *pon = _pon;
rc = qpnp_pon_input_dispatch(pon, PON_RESIN);
if (rc)
dev_err(&pon->pdev->dev, "Unable to send input event\n");
return IRQ_HANDLED;
}
static irqreturn_t qpnp_kpdpwr_resin_bark_irq(int irq, void *_pon)
{
return IRQ_HANDLED;
}
static irqreturn_t qpnp_cblpwr_irq(int irq, void *_pon)
{
int rc;
struct qpnp_pon *pon = _pon;
rc = qpnp_pon_input_dispatch(pon, PON_CBLPWR);
if (rc)
dev_err(&pon->pdev->dev, "Unable to send input event\n");
return IRQ_HANDLED;
}
static void print_pon_reg(struct qpnp_pon *pon, u16 offset)
{
int rc;
u16 addr;
uint reg;
addr = pon->base + offset;
rc = regmap_read(pon->regmap, addr, &reg);
if (rc)
dev_emerg(&pon->pdev->dev,
"Unable to read reg at 0x%04hx\n", addr);
else
dev_emerg(&pon->pdev->dev, "reg@0x%04hx: %02hhx\n", addr, reg);
}
#define PON_PBL_STATUS 0x7
#define PON_PON_REASON1(subtype) PON_OFFSET(subtype, 0x8, 0xC0)
#define PON_PON_REASON2 0x9
#define PON_WARM_RESET_REASON1(subtype) PON_OFFSET(subtype, 0xA, 0xC2)
#define PON_WARM_RESET_REASON2 0xB
#define PON_POFF_REASON1(subtype) PON_OFFSET(subtype, 0xC, 0xC5)
#define PON_POFF_REASON2 0xD
#define PON_SOFT_RESET_REASON1(subtype) PON_OFFSET(subtype, 0xE, 0xCB)
#define PON_SOFT_RESET_REASON2 0xF
#define PON_FAULT_REASON1 0xC8
#define PON_FAULT_REASON2 0xC9
#define PON_PMIC_WD_RESET_S1_TIMER 0x54
#define PON_PMIC_WD_RESET_S2_TIMER 0x55
static irqreturn_t qpnp_pmic_wd_bark_irq(int irq, void *_pon)
{
struct qpnp_pon *pon = _pon;
print_pon_reg(pon, PON_PBL_STATUS);
print_pon_reg(pon, PON_PON_REASON1(pon->subtype));
print_pon_reg(pon, PON_WARM_RESET_REASON1(pon->subtype));
print_pon_reg(pon, PON_SOFT_RESET_REASON1(pon->subtype));
print_pon_reg(pon, PON_POFF_REASON1(pon->subtype));
if (is_pon_gen1(pon) || pon->subtype == PON_1REG) {
print_pon_reg(pon, PON_PON_REASON2);
print_pon_reg(pon, PON_WARM_RESET_REASON2);
print_pon_reg(pon, PON_POFF_REASON2);
print_pon_reg(pon, PON_SOFT_RESET_REASON2);
} else {
print_pon_reg(pon, PON_FAULT_REASON1);
print_pon_reg(pon, PON_FAULT_REASON2);
}
print_pon_reg(pon, PON_PMIC_WD_RESET_S1_TIMER);
print_pon_reg(pon, PON_PMIC_WD_RESET_S2_TIMER);
panic("PMIC Watch dog triggered");
return IRQ_HANDLED;
}
static void bark_work_func(struct work_struct *work)
{
int rc;
uint pon_rt_sts = 0;
struct qpnp_pon_config *cfg;
struct qpnp_pon *pon =
container_of(work, struct qpnp_pon, bark_work.work);
cfg = qpnp_get_cfg(pon, PON_RESIN);
if (!cfg) {
dev_err(&pon->pdev->dev, "Invalid config pointer\n");
goto err_return;
}
/* enable reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, QPNP_PON_S2_CNTL_EN);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S2 enable\n");
goto err_return;
}
/* bark RT status update delay */
msleep(100);
/* read the bark RT status */
rc = regmap_read(pon->regmap, QPNP_PON_RT_STS(pon), &pon_rt_sts);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read PON RT status\n");
goto err_return;
}
if (!(pon_rt_sts & QPNP_PON_RESIN_BARK_N_SET)) {
/* report the key event and enable the bark IRQ */
input_report_key(pon->pon_input, cfg->key_code, 0);
input_sync(pon->pon_input);
enable_irq(cfg->bark_irq);
} else {
/* disable reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, 0);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to configure S2 enable\n");
goto err_return;
}
/* re-arm the work */
schedule_delayed_work(&pon->bark_work, QPNP_KEY_STATUS_DELAY);
}
err_return:
return;
}
static irqreturn_t qpnp_resin_bark_irq(int irq, void *_pon)
{
int rc;
struct qpnp_pon *pon = _pon;
struct qpnp_pon_config *cfg;
/* disable the bark interrupt */
disable_irq_nosync(irq);
cfg = qpnp_get_cfg(pon, PON_RESIN);
if (!cfg) {
dev_err(&pon->pdev->dev, "Invalid config pointer\n");
goto err_exit;
}
/* disable reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, 0);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S2 enable\n");
goto err_exit;
}
/* report the key event */
input_report_key(pon->pon_input, cfg->key_code, 1);
input_sync(pon->pon_input);
/* schedule work to check the bark status for key-release */
schedule_delayed_work(&pon->bark_work, QPNP_KEY_STATUS_DELAY);
err_exit:
return IRQ_HANDLED;
}
static int
qpnp_config_pull(struct qpnp_pon *pon, struct qpnp_pon_config *cfg)
{
int rc;
u8 pull_bit;
switch (cfg->pon_type) {
case PON_KPDPWR:
pull_bit = QPNP_PON_KPDPWR_PULL_UP;
break;
case PON_RESIN:
pull_bit = QPNP_PON_RESIN_PULL_UP;
break;
case PON_CBLPWR:
pull_bit = QPNP_PON_CBLPWR_PULL_UP;
break;
case PON_KPDPWR_RESIN:
pull_bit = QPNP_PON_KPDPWR_PULL_UP | QPNP_PON_RESIN_PULL_UP;
break;
default:
return -EINVAL;
}
rc = qpnp_pon_masked_write(pon, QPNP_PON_PULL_CTL(pon),
pull_bit, cfg->pull_up ? pull_bit : 0);
if (rc)
dev_err(&pon->pdev->dev, "Unable to config pull-up\n");
return rc;
}
static int
qpnp_config_reset(struct qpnp_pon *pon, struct qpnp_pon_config *cfg)
{
int rc;
u8 i;
u16 s1_timer_addr, s2_timer_addr;
switch (cfg->pon_type) {
case PON_KPDPWR:
s1_timer_addr = QPNP_PON_KPDPWR_S1_TIMER(pon);
s2_timer_addr = QPNP_PON_KPDPWR_S2_TIMER(pon);
break;
case PON_RESIN:
s1_timer_addr = QPNP_PON_RESIN_S1_TIMER(pon);
s2_timer_addr = QPNP_PON_RESIN_S2_TIMER(pon);
break;
case PON_KPDPWR_RESIN:
s1_timer_addr = QPNP_PON_KPDPWR_RESIN_S1_TIMER(pon);
s2_timer_addr = QPNP_PON_KPDPWR_RESIN_S2_TIMER(pon);
break;
default:
return -EINVAL;
}
/* disable S2 reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, 0);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S2 enable\n");
return rc;
}
usleep_range(100, 120);
/* configure s1 timer, s2 timer and reset type */
for (i = 0; i < PON_S1_COUNT_MAX + 1; i++) {
if (cfg->s1_timer <= s1_delay[i])
break;
}
rc = qpnp_pon_masked_write(pon, s1_timer_addr,
QPNP_PON_S1_TIMER_MASK, i);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S1 timer\n");
return rc;
}
i = 0;
if (cfg->s2_timer) {
i = cfg->s2_timer / 10;
i = ilog2(i + 1);
}
rc = qpnp_pon_masked_write(pon, s2_timer_addr,
QPNP_PON_S2_TIMER_MASK, i);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S2 timer\n");
return rc;
}
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl_addr,
QPNP_PON_S2_CNTL_TYPE_MASK, (u8)cfg->s2_type);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to configure S2 reset type\n");
return rc;
}
/* enable S2 reset */
rc = qpnp_pon_masked_write(pon, cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, QPNP_PON_S2_CNTL_EN);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to configure S2 enable\n");
return rc;
}
return 0;
}
static int
qpnp_pon_request_irqs(struct qpnp_pon *pon, struct qpnp_pon_config *cfg)
{
int rc = 0;
switch (cfg->pon_type) {
case PON_KPDPWR:
rc = devm_request_irq(&pon->pdev->dev, cfg->state_irq,
qpnp_kpdpwr_irq,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
"qpnp_kpdpwr_status", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev, "Can't request %d IRQ\n",
cfg->state_irq);
return rc;
}
if (cfg->use_bark) {
rc = devm_request_irq(&pon->pdev->dev, cfg->bark_irq,
qpnp_kpdpwr_bark_irq,
IRQF_TRIGGER_RISING,
"qpnp_kpdpwr_bark", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev,
"Can't request %d IRQ\n",
cfg->bark_irq);
return rc;
}
}
break;
case PON_RESIN:
rc = devm_request_irq(&pon->pdev->dev, cfg->state_irq,
qpnp_resin_irq,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
"qpnp_resin_status", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev, "Can't request %d IRQ\n",
cfg->state_irq);
return rc;
}
if (cfg->use_bark) {
rc = devm_request_irq(&pon->pdev->dev, cfg->bark_irq,
qpnp_resin_bark_irq,
IRQF_TRIGGER_RISING,
"qpnp_resin_bark", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev,
"Can't request %d IRQ\n",
cfg->bark_irq);
return rc;
}
}
break;
case PON_CBLPWR:
rc = devm_request_irq(&pon->pdev->dev, cfg->state_irq,
qpnp_cblpwr_irq,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
"qpnp_cblpwr_status", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev, "Can't request %d IRQ\n",
cfg->state_irq);
return rc;
}
break;
case PON_KPDPWR_RESIN:
if (cfg->use_bark) {
rc = devm_request_irq(&pon->pdev->dev, cfg->bark_irq,
qpnp_kpdpwr_resin_bark_irq,
IRQF_TRIGGER_RISING,
"qpnp_kpdpwr_resin_bark", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev,
"Can't request %d IRQ\n",
cfg->bark_irq);
return rc;
}
}
break;
default:
return -EINVAL;
}
/* mark the interrupts wakeable if they support linux-key */
if (cfg->key_code) {
enable_irq_wake(cfg->state_irq);
/* special handling for RESIN due to a hardware bug */
if (cfg->pon_type == PON_RESIN && cfg->support_reset)
enable_irq_wake(cfg->bark_irq);
}
return rc;
}
static int
qpnp_pon_config_input(struct qpnp_pon *pon, struct qpnp_pon_config *cfg)
{
if (!pon->pon_input) {
pon->pon_input = input_allocate_device();
if (!pon->pon_input) {
dev_err(&pon->pdev->dev,
"Can't allocate pon input device\n");
return -ENOMEM;
}
pon->pon_input->name = "qpnp_pon";
pon->pon_input->phys = "qpnp_pon/input0";
}
input_set_capability(pon->pon_input, EV_KEY, cfg->key_code);
return 0;
}
static int qpnp_pon_config_init(struct qpnp_pon *pon)
{
int rc = 0, i = 0, pmic_wd_bark_irq;
struct device_node *pp = NULL;
struct qpnp_pon_config *cfg;
uint pmic_type;
uint revid_rev4;
if (!pon->num_pon_config) {
dev_dbg(&pon->pdev->dev, "num_pon_config: %d\n",
pon->num_pon_config);
return 0;
}
/* iterate through the list of pon configs */
for_each_available_child_of_node(pon->pdev->dev.of_node, pp) {
if (!of_find_property(pp, "qcom,pon-type", NULL))
continue;
cfg = &pon->pon_cfg[i++];
rc = of_property_read_u32(pp, "qcom,pon-type", &cfg->pon_type);
if (rc) {
dev_err(&pon->pdev->dev, "PON type not specified\n");
return rc;
}
switch (cfg->pon_type) {
case PON_KPDPWR:
cfg->state_irq = platform_get_irq_byname(pon->pdev,
"kpdpwr");
if (cfg->state_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get kpdpwr irq\n");
return cfg->state_irq;
}
rc = of_property_read_u32(pp, "qcom,support-reset",
&cfg->support_reset);
if (rc) {
if (rc == -EINVAL) {
dev_dbg(&pon->pdev->dev,
"'qcom,support-reset' DT property doesn't exist\n");
} else {
dev_err(&pon->pdev->dev,
"Unable to read 'qcom,support-reset'\n");
return rc;
}
} else {
cfg->config_reset = true;
}
cfg->use_bark = of_property_read_bool(pp,
"qcom,use-bark");
if (cfg->use_bark) {
cfg->bark_irq
= platform_get_irq_byname(pon->pdev,
"kpdpwr-bark");
if (cfg->bark_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get kpdpwr-bark irq\n");
return cfg->bark_irq;
}
}
/*
* If the value read from REVISION2 register is 0x00,
* then there is a single register to control s2 reset.
* Otherwise there are separate registers for s2 reset
* type and s2 reset enable.
*/
if (pon->pon_ver == QPNP_PON_GEN1_V1) {
cfg->s2_cntl_addr = cfg->s2_cntl2_addr =
QPNP_PON_KPDPWR_S2_CNTL(pon);
} else {
cfg->s2_cntl_addr =
QPNP_PON_KPDPWR_S2_CNTL(pon);
cfg->s2_cntl2_addr =
QPNP_PON_KPDPWR_S2_CNTL2(pon);
}
break;
case PON_RESIN:
cfg->state_irq = platform_get_irq_byname(pon->pdev,
"resin");
if (cfg->state_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get resin irq\n");
return cfg->bark_irq;
}
rc = of_property_read_u32(pp, "qcom,support-reset",
&cfg->support_reset);
if (rc) {
if (rc == -EINVAL) {
dev_dbg(&pon->pdev->dev,
"'qcom,support-reset' DT property doesn't exist\n");
} else {
dev_err(&pon->pdev->dev,
"Unable to read 'qcom,support-reset'\n");
return rc;
}
} else {
cfg->config_reset = true;
}
cfg->use_bark = of_property_read_bool(pp,
"qcom,use-bark");
rc = regmap_read(pon->regmap, PMIC_VERSION_REG,
&pmic_type);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read PMIC type\n");
return rc;
}
if (pmic_type == PMIC_VER_8941) {
rc = regmap_read(pon->regmap,
PMIC_VERSION_REV4_REG,
&revid_rev4);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read PMIC revision ID\n");
return rc;
}
/*
* PM8941 V3 does not have hardware bug. Hence
* bark is not required from PMIC versions 3.0.
*/
if (!(revid_rev4 == PMIC8941_V1_REV4 ||
revid_rev4 == PMIC8941_V2_REV4)) {
cfg->support_reset = false;
cfg->use_bark = false;
}
}
if (cfg->use_bark) {
cfg->bark_irq
= platform_get_irq_byname(pon->pdev,
"resin-bark");
if (cfg->bark_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get resin-bark irq\n");
return cfg->bark_irq;
}
}
if (pon->pon_ver == QPNP_PON_GEN1_V1) {
cfg->s2_cntl_addr = cfg->s2_cntl2_addr =
QPNP_PON_RESIN_S2_CNTL(pon);
} else {
cfg->s2_cntl_addr =
QPNP_PON_RESIN_S2_CNTL(pon);
cfg->s2_cntl2_addr =
QPNP_PON_RESIN_S2_CNTL2(pon);
}
break;
case PON_CBLPWR:
cfg->state_irq = platform_get_irq_byname(pon->pdev,
"cblpwr");
if (cfg->state_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get cblpwr irq\n");
return rc;
}
break;
case PON_KPDPWR_RESIN:
rc = of_property_read_u32(pp, "qcom,support-reset",
&cfg->support_reset);
if (rc) {
if (rc == -EINVAL) {
dev_dbg(&pon->pdev->dev,
"'qcom,support-reset' DT property doesn't exist\n");
} else {
dev_err(&pon->pdev->dev,
"Unable to read 'qcom,support-reset'\n");
return rc;
}
} else {
cfg->config_reset = true;
}
cfg->use_bark = of_property_read_bool(pp,
"qcom,use-bark");
if (cfg->use_bark) {
cfg->bark_irq
= platform_get_irq_byname(pon->pdev,
"kpdpwr-resin-bark");
if (cfg->bark_irq < 0) {
dev_err(&pon->pdev->dev,
"Unable to get kpdpwr-resin-bark irq\n");
return cfg->bark_irq;
}
}
if (pon->pon_ver == QPNP_PON_GEN1_V1) {
cfg->s2_cntl_addr = cfg->s2_cntl2_addr =
QPNP_PON_KPDPWR_RESIN_S2_CNTL(pon);
} else {
cfg->s2_cntl_addr =
QPNP_PON_KPDPWR_RESIN_S2_CNTL(pon);
cfg->s2_cntl2_addr =
QPNP_PON_KPDPWR_RESIN_S2_CNTL2(pon);
}
break;
default:
dev_err(&pon->pdev->dev, "PON RESET %d not supported",
cfg->pon_type);
return -EINVAL;
}
if (cfg->support_reset) {
/*
* Get the reset parameters (bark debounce time and
* reset debounce time) for the reset line.
*/
rc = of_property_read_u32(pp, "qcom,s1-timer",
&cfg->s1_timer);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read s1-timer\n");
return rc;
}
if (cfg->s1_timer > QPNP_PON_S1_TIMER_MAX) {
dev_err(&pon->pdev->dev,
"Incorrect S1 debounce time\n");
return -EINVAL;
}
rc = of_property_read_u32(pp, "qcom,s2-timer",
&cfg->s2_timer);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read s2-timer\n");
return rc;
}
if (cfg->s2_timer > QPNP_PON_S2_TIMER_MAX) {
dev_err(&pon->pdev->dev,
"Incorrect S2 debounce time\n");
return -EINVAL;
}
rc = of_property_read_u32(pp, "qcom,s2-type",
&cfg->s2_type);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read s2-type\n");
return rc;
}
if (cfg->s2_type > QPNP_PON_RESET_TYPE_MAX) {
dev_err(&pon->pdev->dev,
"Incorrect reset type specified\n");
return -EINVAL;
}
}
/*
* Get the standard-key parameters. This might not be
* specified if there is no key mapping on the reset line.
*/
rc = of_property_read_u32(pp, "linux,code", &cfg->key_code);
if (rc && rc != -EINVAL) {
dev_err(&pon->pdev->dev, "Unable to read key-code\n");
return rc;
}
/* Register key configuration */
if (cfg->key_code) {
rc = qpnp_pon_config_input(pon, cfg);
if (rc < 0)
return rc;
}
/* get the pull-up configuration */
rc = of_property_read_u32(pp, "qcom,pull-up", &cfg->pull_up);
if (rc && rc != -EINVAL) {
dev_err(&pon->pdev->dev, "Unable to read pull-up\n");
return rc;
}
}
pmic_wd_bark_irq = platform_get_irq_byname(pon->pdev, "pmic-wd-bark");
/* request the pmic-wd-bark irq only if it is defined */
if (pmic_wd_bark_irq >= 0) {
rc = devm_request_irq(&pon->pdev->dev, pmic_wd_bark_irq,
qpnp_pmic_wd_bark_irq,
IRQF_TRIGGER_RISING,
"qpnp_pmic_wd_bark", pon);
if (rc < 0) {
dev_err(&pon->pdev->dev,
"Can't request %d IRQ\n",
pmic_wd_bark_irq);
goto free_input_dev;
}
}
/* register the input device */
if (pon->pon_input) {
rc = input_register_device(pon->pon_input);
if (rc) {
dev_err(&pon->pdev->dev,
"Can't register pon key: %d\n", rc);
goto free_input_dev;
}
}
for (i = 0; i < pon->num_pon_config; i++) {
cfg = &pon->pon_cfg[i];
/* Configure the pull-up */
rc = qpnp_config_pull(pon, cfg);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to config pull-up\n");
goto unreg_input_dev;
}
if (cfg->config_reset) {
/* Configure the reset-configuration */
if (cfg->support_reset) {
rc = qpnp_config_reset(pon, cfg);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to config pon reset\n");
goto unreg_input_dev;
}
} else {
if (cfg->pon_type != PON_CBLPWR) {
/* disable S2 reset */
rc = qpnp_pon_masked_write(pon,
cfg->s2_cntl2_addr,
QPNP_PON_S2_CNTL_EN, 0);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to disable S2 reset\n");
goto unreg_input_dev;
}
}
}
}
rc = qpnp_pon_request_irqs(pon, cfg);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to request-irq's\n");
goto unreg_input_dev;
}
}
device_init_wakeup(&pon->pdev->dev, 1);
return rc;
unreg_input_dev:
if (pon->pon_input)
input_unregister_device(pon->pon_input);
free_input_dev:
if (pon->pon_input)
input_free_device(pon->pon_input);
return rc;
}
static int pon_spare_regulator_enable(struct regulator_dev *rdev)
{
int rc = 0;
u8 value;
struct pon_regulator *pon_reg = rdev_get_drvdata(rdev);
pr_debug("reg %s enable addr: %x bit: %d\n", rdev->desc->name,
pon_reg->addr, pon_reg->bit);
value = BIT(pon_reg->bit) & 0xFF;
rc = qpnp_pon_masked_write(pon_reg->pon, pon_reg->pon->base +
pon_reg->addr, value, value);
if (rc)
dev_err(&pon_reg->pon->pdev->dev, "Unable to write to %x\n",
pon_reg->pon->base + pon_reg->addr);
else
pon_reg->enabled = true;
return rc;
}
static int pon_spare_regulator_disable(struct regulator_dev *rdev)
{
int rc = 0;
u8 mask;
struct pon_regulator *pon_reg = rdev_get_drvdata(rdev);
pr_debug("reg %s disable addr: %x bit: %d\n", rdev->desc->name,
pon_reg->addr, pon_reg->bit);
mask = BIT(pon_reg->bit) & 0xFF;
rc = qpnp_pon_masked_write(pon_reg->pon, pon_reg->pon->base +
pon_reg->addr, mask, 0);
if (rc)
dev_err(&pon_reg->pon->pdev->dev, "Unable to write to %x\n",
pon_reg->pon->base + pon_reg->addr);
else
pon_reg->enabled = false;
return rc;
}
static int pon_spare_regulator_is_enable(struct regulator_dev *rdev)
{
struct pon_regulator *pon_reg = rdev_get_drvdata(rdev);
return pon_reg->enabled;
}
struct regulator_ops pon_spare_reg_ops = {
.enable = pon_spare_regulator_enable,
.disable = pon_spare_regulator_disable,
.is_enabled = pon_spare_regulator_is_enable,
};
static int pon_regulator_init(struct qpnp_pon *pon)
{
int rc = 0, i = 0;
struct regulator_init_data *init_data;
struct regulator_config reg_cfg = {};
struct device_node *node = NULL;
struct device *dev = &pon->pdev->dev;
struct pon_regulator *pon_reg;
if (!pon->num_pon_reg)
return 0;
pon->pon_reg_cfg = devm_kcalloc(dev, pon->num_pon_reg,
sizeof(*(pon->pon_reg_cfg)),
GFP_KERNEL);
if (!pon->pon_reg_cfg)
return -ENOMEM;
for_each_available_child_of_node(dev->of_node, node) {
if (!of_find_property(node, "regulator-name", NULL))
continue;
pon_reg = &pon->pon_reg_cfg[i++];
pon_reg->pon = pon;
rc = of_property_read_u32(node, "qcom,pon-spare-reg-addr",
&pon_reg->addr);
if (rc) {
dev_err(dev, "Unable to read address for regulator, rc=%d\n",
rc);
return rc;
}
rc = of_property_read_u32(node, "qcom,pon-spare-reg-bit",
&pon_reg->bit);
if (rc) {
dev_err(dev, "Unable to read bit for regulator, rc=%d\n",
rc);
return rc;
}
init_data = of_get_regulator_init_data(dev, node,
&pon_reg->rdesc);
if (!init_data) {
dev_err(dev, "regulator init data is missing\n");
return -EINVAL;
}
init_data->constraints.valid_ops_mask
|= REGULATOR_CHANGE_STATUS;
if (!init_data->constraints.name) {
dev_err(dev, "regulator-name is missing\n");
return -EINVAL;
}
pon_reg->rdesc.owner = THIS_MODULE;
pon_reg->rdesc.type = REGULATOR_VOLTAGE;
pon_reg->rdesc.ops = &pon_spare_reg_ops;
pon_reg->rdesc.name = init_data->constraints.name;
reg_cfg.dev = dev;
reg_cfg.init_data = init_data;
reg_cfg.driver_data = pon_reg;
reg_cfg.of_node = node;
pon_reg->rdev = regulator_register(&pon_reg->rdesc, &reg_cfg);
if (IS_ERR(pon_reg->rdev)) {
rc = PTR_ERR(pon_reg->rdev);
pon_reg->rdev = NULL;
if (rc != -EPROBE_DEFER)
dev_err(dev, "regulator_register failed, rc=%d\n",
rc);
return rc;
}
}
return rc;
}
static bool smpl_en;
static int qpnp_pon_smpl_en_get(char *buf, const struct kernel_param *kp)
{
bool enabled = 0;
int rc;
rc = qpnp_pon_get_trigger_config(PON_SMPL, &enabled);
if (rc < 0)
return rc;
return snprintf(buf, QPNP_PON_BUFFER_SIZE, "%d", enabled);
}
static int qpnp_pon_smpl_en_set(const char *val,
const struct kernel_param *kp)
{
int rc;
rc = param_set_bool(val, kp);
if (rc < 0) {
pr_err("Unable to set smpl_en rc=%d\n", rc);
return rc;
}
rc = qpnp_pon_trigger_config(PON_SMPL, *(bool *)kp->arg);
return rc;
}
static struct kernel_param_ops smpl_en_ops = {
.set = qpnp_pon_smpl_en_set,
.get = qpnp_pon_smpl_en_get,
};
module_param_cb(smpl_en, &smpl_en_ops, &smpl_en, 0644);
static bool dload_on_uvlo;
static int qpnp_pon_debugfs_uvlo_dload_get(char *buf,
const struct kernel_param *kp)
{
struct qpnp_pon *pon = sys_reset_dev;
int rc = 0;
uint reg;
if (!pon)
return -ENODEV;
rc = regmap_read(pon->regmap, QPNP_PON_XVDD_RB_SPARE(pon), &reg);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read addr=%x, rc(%d)\n",
QPNP_PON_XVDD_RB_SPARE(pon), rc);
return rc;
}
return snprintf(buf, PAGE_SIZE, "%d",
!!(QPNP_PON_UVLO_DLOAD_EN & reg));
}
static int qpnp_pon_debugfs_uvlo_dload_set(const char *val,
const struct kernel_param *kp)
{
struct qpnp_pon *pon = sys_reset_dev;
int rc = 0;
uint reg;
if (!pon)
return -ENODEV;
rc = param_set_bool(val, kp);
if (rc) {
pr_err("Unable to set bms_reset: %d\n", rc);
return rc;
}
rc = regmap_read(pon->regmap, QPNP_PON_XVDD_RB_SPARE(pon), &reg);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read addr=%x, rc(%d)\n",
QPNP_PON_XVDD_RB_SPARE(pon), rc);
return rc;
}
reg &= ~QPNP_PON_UVLO_DLOAD_EN;
if (*(bool *)kp->arg)
reg |= QPNP_PON_UVLO_DLOAD_EN;
rc = regmap_write(pon->regmap, QPNP_PON_XVDD_RB_SPARE(pon), reg);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to write to addr=%hx, rc(%d)\n",
QPNP_PON_XVDD_RB_SPARE(pon), rc);
return rc;
}
return 0;
}
static struct kernel_param_ops dload_on_uvlo_ops = {
.set = qpnp_pon_debugfs_uvlo_dload_set,
.get = qpnp_pon_debugfs_uvlo_dload_get,
};
module_param_cb(dload_on_uvlo, &dload_on_uvlo_ops, &dload_on_uvlo, 0644);
#if defined(CONFIG_DEBUG_FS)
static int qpnp_pon_debugfs_uvlo_get(void *data, u64 *val)
{
struct qpnp_pon *pon = (struct qpnp_pon *) data;
*val = pon->uvlo;
return 0;
}
static int qpnp_pon_debugfs_uvlo_set(void *data, u64 val)
{
struct qpnp_pon *pon = (struct qpnp_pon *) data;
if (pon->pon_trigger_reason == PON_SMPL ||
pon->pon_power_off_reason == QPNP_POFF_REASON_UVLO)
panic("An UVLO was occurred.\n");
pon->uvlo = val;
return 0;
}
DEFINE_SIMPLE_ATTRIBUTE(qpnp_pon_debugfs_uvlo_fops, qpnp_pon_debugfs_uvlo_get,
qpnp_pon_debugfs_uvlo_set, "0x%02llx\n");
static void qpnp_pon_debugfs_init(struct platform_device *pdev)
{
struct qpnp_pon *pon = dev_get_drvdata(&pdev->dev);
struct dentry *ent;
pon->debugfs = debugfs_create_dir(dev_name(&pdev->dev), NULL);
if (!pon->debugfs) {
dev_err(&pon->pdev->dev,
"Unable to create debugfs directory\n");
} else {
ent = debugfs_create_file("uvlo_panic", 0644,
pon->debugfs, pon, &qpnp_pon_debugfs_uvlo_fops);
if (!ent)
dev_err(&pon->pdev->dev,
"Unable to create uvlo_panic debugfs file.\n");
}
}
static void qpnp_pon_debugfs_remove(struct platform_device *pdev)
{
struct qpnp_pon *pon = dev_get_drvdata(&pdev->dev);
debugfs_remove_recursive(pon->debugfs);
}
#else
static void qpnp_pon_debugfs_init(struct platform_device *pdev)
{}
static void qpnp_pon_debugfs_remove(struct platform_device *pdev)
{}
#endif
static int read_gen2_pon_off_reason(struct qpnp_pon *pon, u16 *reason,
int *reason_index_offset)
{
int rc;
int buf[2], reg;
rc = regmap_read(pon->regmap,
QPNP_PON_OFF_REASON(pon),
&reg);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read PON_OFF_REASON reg rc:%d\n",
rc);
return rc;
}
if (reg & QPNP_GEN2_POFF_SEQ) {
rc = regmap_read(pon->regmap,
QPNP_POFF_REASON1(pon),
buf);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read POFF_REASON1 reg rc:%d\n",
rc);
return rc;
}
*reason = (u8)buf[0];
*reason_index_offset = 0;
} else if (reg & QPNP_GEN2_FAULT_SEQ) {
rc = regmap_bulk_read(pon->regmap,
QPNP_FAULT_REASON1(pon),
buf, 2);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read FAULT_REASON regs rc:%d\n",
rc);
return rc;
}
*reason = (u8)buf[0] | (u16)(buf[1] << 8);
*reason_index_offset = POFF_REASON_FAULT_OFFSET;
} else if (reg & QPNP_GEN2_S3_RESET_SEQ) {
rc = regmap_read(pon->regmap,
QPNP_S3_RESET_REASON(pon),
buf);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read S3_RESET_REASON reg rc:%d\n",
rc);
return rc;
}
*reason = (u8)buf[0];
*reason_index_offset = POFF_REASON_S3_RESET_OFFSET;
}
return 0;
}
static int pon_twm_notifier_cb(struct notifier_block *nb,
unsigned long action, void *data)
{
struct qpnp_pon *pon = container_of(nb, struct qpnp_pon, pon_nb);
if (action != PMIC_TWM_CLEAR &&
action != PMIC_TWM_ENABLE) {
pr_debug("Unsupported option %lu\n", action);
return NOTIFY_OK;
}
pon->twm_state = (u8)action;
pr_debug("TWM state = %d\n", pon->twm_state);
return NOTIFY_OK;
}
static int pon_register_twm_notifier(struct qpnp_pon *pon)
{
int rc;
pon->pon_nb.notifier_call = pon_twm_notifier_cb;
rc = qpnp_misc_twm_notifier_register(&pon->pon_nb);
if (rc < 0)
pr_err("Failed to register pon_twm_notifier_cb rc=%d\n", rc);
return rc;
}
static int qpnp_pon_probe(struct platform_device *pdev)
{
struct qpnp_pon *pon;
unsigned int base;
struct device_node *node = NULL;
u32 delay = 0, s3_debounce = 0;
int rc, sys_reset, index;
int reason_index_offset = 0;
u8 buf[2];
uint pon_sts = 0;
u16 poff_sts = 0;
const char *s3_src;
u8 s3_src_reg;
unsigned long flags;
uint temp = 0;
pon = devm_kzalloc(&pdev->dev, sizeof(struct qpnp_pon), GFP_KERNEL);
if (!pon)
return -ENOMEM;
pon->regmap = dev_get_regmap(pdev->dev.parent, NULL);
if (!pon->regmap) {
dev_err(&pdev->dev, "Couldn't get parent's regmap\n");
return -EINVAL;
}
sys_reset = of_property_read_bool(pdev->dev.of_node,
"qcom,system-reset");
if (sys_reset && sys_reset_dev) {
dev_err(&pdev->dev,
"qcom,system-reset property can only be specified for one device on the system\n");
return -EINVAL;
} else if (sys_reset) {
sys_reset_dev = pon;
}
pon->pdev = pdev;
rc = of_property_read_u32(pdev->dev.of_node, "reg", &base);
if (rc < 0) {
dev_err(&pdev->dev,
"Couldn't find reg in node = %s rc = %d\n",
pdev->dev.of_node->full_name, rc);
goto err_out;
}
pon->base = base;
/* get the total number of pon configurations */
for_each_available_child_of_node(pdev->dev.of_node, node) {
if (of_find_property(node, "regulator-name", NULL)) {
pon->num_pon_reg++;
} else if (of_find_property(node, "qcom,pon-type", NULL)) {
pon->num_pon_config++;
} else {
pr_err("Unknown sub-node\n");
rc = -EINVAL;
goto err_out;
}
}
pr_debug("PON@SID %d: num_pon_config: %d num_pon_reg: %d\n",
to_spmi_device(pon->pdev->dev.parent)->usid,
pon->num_pon_config, pon->num_pon_reg);
rc = pon_regulator_init(pon);
if (rc) {
dev_err(&pdev->dev, "Error in pon_regulator_init rc: %d\n",
rc);
goto err_out;
}
if (!pon->num_pon_config)
/* No PON config., do not register the driver */
dev_info(&pdev->dev, "No PON config. specified\n");
else
pon->pon_cfg = devm_kzalloc(&pdev->dev,
sizeof(struct qpnp_pon_config) *
pon->num_pon_config, GFP_KERNEL);
/* Read PON_PERPH_SUBTYPE register to get PON type */
rc = regmap_read(pon->regmap,
QPNP_PON_PERPH_SUBTYPE(pon),
&temp);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read PON_PERPH_SUBTYPE register rc: %d\n",
rc);
goto err_out;
}
pon->subtype = temp;
/* Check if it is rev B */
rc = regmap_read(pon->regmap,
QPNP_PON_REVISION2(pon), &temp);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read addr=%x, rc(%d)\n",
QPNP_PON_REVISION2(pon), rc);
goto err_out;
}
pon->pon_ver = temp;
if (is_pon_gen1(pon)) {
if (pon->pon_ver == 0)
pon->pon_ver = QPNP_PON_GEN1_V1;
else
pon->pon_ver = QPNP_PON_GEN1_V2;
} else if (is_pon_gen2(pon)) {
pon->pon_ver = QPNP_PON_GEN2;
} else if (pon->subtype == PON_1REG) {
pon->pon_ver = QPNP_PON_GEN1_V2;
} else {
dev_err(&pon->pdev->dev,
"Invalid PON_PERPH_SUBTYPE value %x\n",
pon->subtype);
goto err_out;
}
pr_debug("%s: pon_subtype=%x, pon_version=%x\n", __func__,
pon->subtype, pon->pon_ver);
rc = qpnp_pon_store_and_clear_warm_reset(pon);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to store/clear WARM_RESET_REASONx registers rc: %d\n",
rc);
goto err_out;
}
/* PON reason */
rc = regmap_read(pon->regmap, QPNP_PON_REASON1(pon), &pon_sts);
if (rc) {
dev_err(&pon->pdev->dev,
"Unable to read PON_RESASON1 reg rc: %d\n",
rc);
goto err_out;
}
if (sys_reset)
boot_reason = ffs(pon_sts);
index = ffs(pon_sts) - 1;
cold_boot = !qpnp_pon_is_warm_reset();
if (index >= ARRAY_SIZE(qpnp_pon_reason) || index < 0) {
dev_info(&pon->pdev->dev,
"PMIC@SID%d Power-on reason: Unknown and '%s' boot\n",
to_spmi_device(pon->pdev->dev.parent)->usid,
cold_boot ? "cold" : "warm");
} else {
pon->pon_trigger_reason = index;
dev_info(&pon->pdev->dev,
"PMIC@SID%d Power-on reason: %s and '%s' boot\n",
to_spmi_device(pon->pdev->dev.parent)->usid,
qpnp_pon_reason[index],
cold_boot ? "cold" : "warm");
}
/* POFF reason */
if (!is_pon_gen1(pon) && pon->subtype != PON_1REG) {
rc = read_gen2_pon_off_reason(pon, &poff_sts,
&reason_index_offset);
if (rc)
goto err_out;
} else {
rc = regmap_bulk_read(pon->regmap, QPNP_POFF_REASON1(pon),
buf, 2);
if (rc) {
dev_err(&pon->pdev->dev, "Unable to read POFF_REASON regs rc:%d\n",
rc);
goto err_out;
}
poff_sts = buf[0] | (buf[1] << 8);
}
index = ffs(poff_sts) - 1 + reason_index_offset;
if (index >= ARRAY_SIZE(qpnp_poff_reason) || index < 0) {
dev_info(&pon->pdev->dev,
"PMIC@SID%d: Unknown power-off reason\n",
to_spmi_device(pon->pdev->dev.parent)->usid);
} else {
pon->pon_power_off_reason = index;
dev_info(&pon->pdev->dev,
"PMIC@SID%d: Power-off reason: %s\n",
to_spmi_device(pon->pdev->dev.parent)->usid,
qpnp_poff_reason[index]);
}
if (pon->pon_trigger_reason == PON_SMPL ||
pon->pon_power_off_reason == QPNP_POFF_REASON_UVLO) {
if (of_property_read_bool(pdev->dev.of_node,
"qcom,uvlo-panic"))
panic("An UVLO was occurred.");
}
/* program s3 debounce */
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,s3-debounce", &s3_debounce);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pon->pdev->dev,
"Unable to read s3 timer rc:%d\n",
rc);
goto err_out;
}
} else {
if (s3_debounce > QPNP_PON_S3_TIMER_SECS_MAX) {
dev_info(&pon->pdev->dev,
"Exceeded S3 max value, set it to max\n");
s3_debounce = QPNP_PON_S3_TIMER_SECS_MAX;
}
/* 0 is a special value to indicate instant s3 reset */
if (s3_debounce != 0)
s3_debounce = ilog2(s3_debounce);
/* s3 debounce is SEC_ACCESS register */
rc = qpnp_pon_masked_write(pon, QPNP_PON_SEC_ACCESS(pon),
0xFF, QPNP_PON_SEC_UNLOCK);
if (rc) {
dev_err(&pdev->dev, "Unable to do SEC_ACCESS rc:%d\n",
rc);
goto err_out;
}
rc = qpnp_pon_masked_write(pon, QPNP_PON_S3_DBC_CTL(pon),
QPNP_PON_S3_DBC_DELAY_MASK, s3_debounce);
if (rc) {
dev_err(&pdev->dev,
"Unable to set S3 debounce rc:%d\n",
rc);
goto err_out;
}
}
/* program s3 source */
s3_src = "kpdpwr-and-resin";
rc = of_property_read_string(pon->pdev->dev.of_node,
"qcom,s3-src", &s3_src);
if (rc && rc != -EINVAL) {
dev_err(&pon->pdev->dev, "Unable to read s3 timer rc: %d\n",
rc);
goto err_out;
}
if (!strcmp(s3_src, "kpdpwr"))
s3_src_reg = QPNP_PON_S3_SRC_KPDPWR;
else if (!strcmp(s3_src, "resin"))
s3_src_reg = QPNP_PON_S3_SRC_RESIN;
else if (!strcmp(s3_src, "kpdpwr-or-resin"))
s3_src_reg = QPNP_PON_S3_SRC_KPDPWR_OR_RESIN;
else /* default combination */
s3_src_reg = QPNP_PON_S3_SRC_KPDPWR_AND_RESIN;
/*
* S3 source is a write once register. If the register has
* been configured by bootloader then this operation will
* not be effective.
*/
rc = qpnp_pon_masked_write(pon, QPNP_PON_S3_SRC(pon),
QPNP_PON_S3_SRC_MASK, s3_src_reg);
if (rc) {
dev_err(&pdev->dev, "Unable to program s3 source rc: %d\n",
rc);
goto err_out;
}
dev_set_drvdata(&pdev->dev, pon);
INIT_DELAYED_WORK(&pon->bark_work, bark_work_func);
/* register the PON configurations */
rc = qpnp_pon_config_init(pon);
if (rc) {
dev_err(&pdev->dev,
"Unable to initialize PON configurations rc: %d\n", rc);
goto err_out;
}
if (of_property_read_bool(pon->pdev->dev.of_node,
"qcom,support-twm-config")) {
pon->support_twm_config = true;
rc = pon_register_twm_notifier(pon);
if (rc < 0) {
pr_err("Failed to register TWM notifier rc=%d\n", rc);
return rc;
}
pon->pbs_dev_node = of_parse_phandle(pon->pdev->dev.of_node,
"qcom,pbs-client", 0);
if (!pon->pbs_dev_node) {
pr_err("Missing qcom,pbs-client property\n");
return -EINVAL;
}
}
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,pon-dbc-delay", &delay);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev,
"Unable to read debounce delay rc: %d\n", rc);
goto err_out;
}
} else {
rc = qpnp_pon_set_dbc(pon, delay);
if (rc) {
dev_err(&pdev->dev,
"Unable to set PON debounce delay rc=%d\n", rc);
goto err_out;
}
}
rc = qpnp_pon_get_dbc(pon, &pon->dbc_time_us);
if (rc) {
dev_err(&pdev->dev,
"Unable to get PON debounce delay rc=%d\n", rc);
goto err_out;
}
pon->kpdpwr_dbc_enable = of_property_read_bool(pon->pdev->dev.of_node,
"qcom,kpdpwr-sw-debounce");
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,warm-reset-poweroff-type",
&pon->warm_reset_poff_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read warm reset poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->warm_reset_poff_type = -EINVAL;
} else if (pon->warm_reset_poff_type <= PON_POWER_OFF_RESERVED ||
pon->warm_reset_poff_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid warm-reset-poweroff-type\n");
pon->warm_reset_poff_type = -EINVAL;
}
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,hard-reset-poweroff-type",
&pon->hard_reset_poff_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read hard reset poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->hard_reset_poff_type = -EINVAL;
} else if (pon->hard_reset_poff_type <= PON_POWER_OFF_RESERVED ||
pon->hard_reset_poff_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid hard-reset-poweroff-type\n");
pon->hard_reset_poff_type = -EINVAL;
}
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,shutdown-poweroff-type",
&pon->shutdown_poff_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read shutdown poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->shutdown_poff_type = -EINVAL;
} else if (pon->shutdown_poff_type <= PON_POWER_OFF_RESERVED ||
pon->shutdown_poff_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid shutdown-poweroff-type\n");
pon->shutdown_poff_type = -EINVAL;
}
pon->ps_hold_hard_reset_disable =
of_property_read_bool(pdev->dev.of_node,
"qcom,ps-hold-hard-reset-disable");
pon->ps_hold_shutdown_disable = of_property_read_bool(pdev->dev.of_node,
"qcom,ps-hold-shutdown-disable");
pon->resin_pon_reset = of_property_read_bool(pdev->dev.of_node,
"qcom,resin-pon-reset");
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,resin-warm-reset-type",
&pon->resin_warm_reset_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read resin warm reset poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->resin_warm_reset_type = -EINVAL;
} else if (pon->resin_warm_reset_type <= PON_POWER_OFF_RESERVED ||
pon->resin_warm_reset_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid resin-warm-reset-type\n");
pon->resin_warm_reset_type = -EINVAL;
}
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,resin-hard-reset-type",
&pon->resin_hard_reset_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read resin hard reset poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->resin_hard_reset_type = -EINVAL;
} else if (pon->resin_hard_reset_type <= PON_POWER_OFF_RESERVED ||
pon->resin_hard_reset_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid resin-hard-reset-type\n");
pon->resin_hard_reset_type = -EINVAL;
}
rc = of_property_read_u32(pon->pdev->dev.of_node,
"qcom,resin-shutdown-type",
&pon->resin_shutdown_type);
if (rc) {
if (rc != -EINVAL) {
dev_err(&pdev->dev, "Unable to read resin shutdown poweroff type rc: %d\n",
rc);
goto err_out;
}
pon->resin_shutdown_type = -EINVAL;
} else if (pon->resin_shutdown_type <= PON_POWER_OFF_RESERVED ||
pon->resin_shutdown_type >= PON_POWER_OFF_MAX_TYPE) {
dev_err(&pdev->dev, "Invalid resin-shutdown-type\n");
pon->resin_shutdown_type = -EINVAL;
}
pon->resin_hard_reset_disable = of_property_read_bool(pdev->dev.of_node,
"qcom,resin-hard-reset-disable");
pon->resin_shutdown_disable = of_property_read_bool(pdev->dev.of_node,
"qcom,resin-shutdown-disable");
rc = device_create_file(&pdev->dev, &dev_attr_debounce_us);
if (rc) {
dev_err(&pdev->dev, "sys file creation failed rc: %d\n", rc);
goto err_out;
}
if (of_property_read_bool(pdev->dev.of_node,
"qcom,secondary-pon-reset")) {
if (sys_reset) {
dev_err(&pdev->dev,
"qcom,system-reset property shouldn't be used along with qcom,secondary-pon-reset property\n");
rc = -EINVAL;
goto err_out;
}
spin_lock_irqsave(&spon_list_slock, flags);
list_add(&pon->list, &spon_dev_list);
spin_unlock_irqrestore(&spon_list_slock, flags);
pon->is_spon = true;
}
/* config whether store the hard reset reason */
pon->store_hard_reset_reason = of_property_read_bool(pdev->dev.of_node,
"qcom,store-hard-reset-reason");
pon->legacy_hard_reset_offset = of_property_read_bool(pdev->dev.of_node,
"qcom,use-legacy-hard-reset-offset");
qpnp_pon_debugfs_init(pdev);
return 0;
err_out:
if (sys_reset)
sys_reset_dev = NULL;
return rc;
}
static int qpnp_pon_remove(struct platform_device *pdev)
{
struct qpnp_pon *pon = dev_get_drvdata(&pdev->dev);
unsigned long flags;
device_remove_file(&pdev->dev, &dev_attr_debounce_us);
cancel_delayed_work_sync(&pon->bark_work);
if (pon->pon_input)
input_unregister_device(pon->pon_input);
qpnp_pon_debugfs_remove(pdev);
if (pon->is_spon) {
spin_lock_irqsave(&spon_list_slock, flags);
list_del(&pon->list);
spin_unlock_irqrestore(&spon_list_slock, flags);
}
return 0;
}
static const struct of_device_id spmi_match_table[] = {
{ .compatible = "qcom,qpnp-power-on", },
{}
};
static struct platform_driver qpnp_pon_driver = {
.driver = {
.name = "qcom,qpnp-power-on",
.of_match_table = spmi_match_table,
},
.probe = qpnp_pon_probe,
.remove = qpnp_pon_remove,
};
static int __init qpnp_pon_init(void)
{
return platform_driver_register(&qpnp_pon_driver);
}
subsys_initcall(qpnp_pon_init);
static void __exit qpnp_pon_exit(void)
{
return platform_driver_unregister(&qpnp_pon_driver);
}
module_exit(qpnp_pon_exit);
MODULE_DESCRIPTION("QPNP PMIC POWER-ON driver");
MODULE_LICENSE("GPL v2");