include/linux/ssb/ssb_regs.h - kernel/msm-4.9 - Gitiles

 #ifndef LINUX_SSB_REGS_H_
 #define LINUX_SSB_REGS_H_


 /* SiliconBackplane Address Map.
  * All regions may not exist on all chips.
  */
 #define SSB_SDRAM_BASE		0x00000000U	/* Physical SDRAM */
 #define SSB_PCI_MEM		0x08000000U	/* Host Mode sb2pcitranslation0 (64 MB) */
 #define SSB_PCI_CFG		0x0c000000U	/* Host Mode sb2pcitranslation1 (64 MB) */
 #define	SSB_SDRAM_SWAPPED	0x10000000U	/* Byteswapped Physical SDRAM */
 #define SSB_ENUM_BASE    	0x18000000U	/* Enumeration space base */
 #define	SSB_ENUM_LIMIT		0x18010000U	/* Enumeration space limit */

 #define	SSB_FLASH2		0x1c000000U	/* Flash Region 2 (region 1 shadowed here) */
 #define	SSB_FLASH2_SZ		0x02000000U	/* Size of Flash Region 2 */

 #define	SSB_EXTIF_BASE		0x1f000000U	/* External Interface region base address */
 #define	SSB_FLASH1		0x1fc00000U	/* Flash Region 1 */
 #define	SSB_FLASH1_SZ		0x00400000U	/* Size of Flash Region 1 */

 #define SSB_PCI_DMA		0x40000000U	/* Client Mode sb2pcitranslation2 (1 GB) */
 #define SSB_PCI_DMA_SZ		0x40000000U	/* Client Mode sb2pcitranslation2 size in bytes */
 #define SSB_PCIE_DMA_L32	0x00000000U	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */
 #define SSB_PCIE_DMA_H32	0x80000000U	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */
 #define	SSB_EUART		(SSB_EXTIF_BASE + 0x00800000)
 #define	SSB_LED			(SSB_EXTIF_BASE + 0x00900000)


 /* Enumeration space constants */
 #define SSB_CORE_SIZE		0x1000	/* Size of a core MMIO area */
 #define SSB_MAX_NR_CORES	((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE)


 /* mips address */
 #define	SSB_EJTAG		0xff200000	/* MIPS EJTAG space (2M) */


 /* SSB PCI config space registers. */
 #define SSB_PMCSR		0x44
 #define  SSB_PE			0x100
 #define	SSB_BAR0_WIN		0x80	/* Backplane address space 0 */
 #define	SSB_BAR1_WIN		0x84	/* Backplane address space 1 */
 #define	SSB_SPROMCTL		0x88	/* SPROM control */
 #define  SSB_SPROMCTL_WE	0x10	/* SPROM write enable */
 #define	SSB_BAR1_CONTROL	0x8c	/* Address space 1 burst control */
 #define SSB_PCI_IRQS		0x90	/* PCI interrupts */
 #define SSB_PCI_IRQMASK		0x94	/* PCI IRQ control and mask (pcirev >= 6 only) */
 #define SSB_BACKPLANE_IRQS	0x98	/* Backplane Interrupts */
 #define SSB_GPIO_IN		0xB0	/* GPIO Input (pcirev >= 3 only) */
 #define SSB_GPIO_OUT		0xB4	/* GPIO Output (pcirev >= 3 only) */
 #define SSB_GPIO_OUT_ENABLE	0xB8	/* GPIO Output Enable/Disable (pcirev >= 3 only) */
 #define  SSB_GPIO_SCS		0x10	/* PCI config space bit 4 for 4306c0 slow clock source */
 #define  SSB_GPIO_HWRAD		0x20	/* PCI config space GPIO 13 for hw radio disable */
 #define  SSB_GPIO_XTAL		0x40	/* PCI config space GPIO 14 for Xtal powerup */
 #define  SSB_GPIO_PLL		0x80	/* PCI config space GPIO 15 for PLL powerdown */


 #define SSB_BAR0_MAX_RETRIES	50

 /* Silicon backplane configuration register definitions */
 #define SSB_IPSFLAG		0x0F08
 #define	 SSB_IPSFLAG_IRQ1	0x0000003F /* which sbflags get routed to mips interrupt 1 */
 #define	 SSB_IPSFLAG_IRQ1_SHIFT	0
 #define	 SSB_IPSFLAG_IRQ2	0x00003F00 /* which sbflags get routed to mips interrupt 2 */
 #define	 SSB_IPSFLAG_IRQ2_SHIFT	8
 #define	 SSB_IPSFLAG_IRQ3	0x003F0000 /* which sbflags get routed to mips interrupt 3 */
 #define	 SSB_IPSFLAG_IRQ3_SHIFT	16
 #define	 SSB_IPSFLAG_IRQ4	0x3F000000 /* which sbflags get routed to mips interrupt 4 */
 #define	 SSB_IPSFLAG_IRQ4_SHIFT	24
 #define SSB_TPSFLAG		0x0F18
 #define  SSB_TPSFLAG_BPFLAG	0x0000003F /* Backplane flag # */
 #define  SSB_TPSFLAG_ALWAYSIRQ	0x00000040 /* IRQ is always sent on the Backplane */
 #define SSB_TMERRLOGA		0x0F48
 #define SSB_TMERRLOG		0x0F50
 #define SSB_ADMATCH3		0x0F60
 #define SSB_ADMATCH2		0x0F68
 #define SSB_ADMATCH1		0x0F70
 #define SSB_IMSTATE		0x0F90     /* SB Initiator Agent State */
 #define  SSB_IMSTATE_PC		0x0000000f /* Pipe Count */
 #define  SSB_IMSTATE_AP_MASK	0x00000030 /* Arbitration Priority */
 #define  SSB_IMSTATE_AP_BOTH	0x00000000 /* Use both timeslices and token */
 #define  SSB_IMSTATE_AP_TS	0x00000010 /* Use timeslices only */
 #define  SSB_IMSTATE_AP_TK	0x00000020 /* Use token only */
 #define  SSB_IMSTATE_AP_RSV	0x00000030 /* Reserved */
 #define  SSB_IMSTATE_IBE	0x00020000 /* In Band Error */
 #define  SSB_IMSTATE_TO		0x00040000 /* Timeout */
 #define SSB_INTVEC		0x0F94     /* SB Interrupt Mask */
 #define  SSB_INTVEC_PCI		0x00000001 /* Enable interrupts for PCI */
 #define  SSB_INTVEC_ENET0	0x00000002 /* Enable interrupts for enet 0 */
 #define  SSB_INTVEC_ILINE20	0x00000004 /* Enable interrupts for iline20 */
 #define  SSB_INTVEC_CODEC	0x00000008 /* Enable interrupts for v90 codec */
 #define  SSB_INTVEC_USB		0x00000010 /* Enable interrupts for usb */
 #define  SSB_INTVEC_EXTIF	0x00000020 /* Enable interrupts for external i/f */
 #define  SSB_INTVEC_ENET1	0x00000040 /* Enable interrupts for enet 1 */
 #define SSB_TMSLOW		0x0F98     /* SB Target State Low */
 #define  SSB_TMSLOW_RESET	0x00000001 /* Reset */
 #define  SSB_TMSLOW_REJECT_22	0x00000002 /* Reject (Backplane rev 2.2) */
 #define  SSB_TMSLOW_REJECT_23	0x00000004 /* Reject (Backplane rev 2.3) */
 #define  SSB_TMSLOW_CLOCK	0x00010000 /* Clock Enable */
 #define  SSB_TMSLOW_FGC		0x00020000 /* Force Gated Clocks On */
 #define  SSB_TMSLOW_PE		0x40000000 /* Power Management Enable */
 #define  SSB_TMSLOW_BE		0x80000000 /* BIST Enable */
 #define SSB_TMSHIGH		0x0F9C     /* SB Target State High */
 #define  SSB_TMSHIGH_SERR	0x00000001 /* S-error */
 #define  SSB_TMSHIGH_INT	0x00000002 /* Interrupt */
 #define  SSB_TMSHIGH_BUSY	0x00000004 /* Busy */
 #define  SSB_TMSHIGH_TO		0x00000020 /* Timeout. Backplane rev >= 2.3 only */
 #define  SSB_TMSHIGH_COREFL	0x1FFF0000 /* Core specific flags */
 #define  SSB_TMSHIGH_COREFL_SHIFT	16
 #define  SSB_TMSHIGH_DMA64	0x10000000 /* 64bit DMA supported */
 #define  SSB_TMSHIGH_GCR	0x20000000 /* Gated Clock Request */
 #define  SSB_TMSHIGH_BISTF	0x40000000 /* BIST Failed */
 #define  SSB_TMSHIGH_BISTD	0x80000000 /* BIST Done */
 #define SSB_BWA0		0x0FA0
 #define SSB_IMCFGLO		0x0FA8
 #define  SSB_IMCFGLO_SERTO	0x00000007 /* Service timeout */
 #define  SSB_IMCFGLO_REQTO	0x00000070 /* Request timeout */
 #define  SSB_IMCFGLO_REQTO_SHIFT	4
 #define  SSB_IMCFGLO_CONNID	0x00FF0000 /* Connection ID */
 #define  SSB_IMCFGLO_CONNID_SHIFT	16
 #define SSB_IMCFGHI		0x0FAC
 #define SSB_ADMATCH0		0x0FB0
 #define SSB_TMCFGLO		0x0FB8
 #define SSB_TMCFGHI		0x0FBC
 #define SSB_BCONFIG		0x0FC0
 #define SSB_BSTATE		0x0FC8
 #define SSB_ACTCFG		0x0FD8
 #define SSB_FLAGST		0x0FE8
 #define SSB_IDLOW		0x0FF8
 #define  SSB_IDLOW_CFGSP	0x00000003 /* Config Space */
 #define  SSB_IDLOW_ADDRNGE	0x00000038 /* Address Ranges supported */
 #define  SSB_IDLOW_ADDRNGE_SHIFT	3
 #define  SSB_IDLOW_SYNC		0x00000040
 #define  SSB_IDLOW_INITIATOR	0x00000080
 #define  SSB_IDLOW_MIBL		0x00000F00 /* Minimum Backplane latency */
 #define  SSB_IDLOW_MIBL_SHIFT	8
 #define  SSB_IDLOW_MABL		0x0000F000 /* Maximum Backplane latency */
 #define  SSB_IDLOW_MABL_SHIFT	12
 #define  SSB_IDLOW_TIF		0x00010000 /* This Initiator is first */
 #define  SSB_IDLOW_CCW		0x000C0000 /* Cycle counter width */
 #define  SSB_IDLOW_CCW_SHIFT	18
 #define  SSB_IDLOW_TPT		0x00F00000 /* Target ports */
 #define  SSB_IDLOW_TPT_SHIFT	20
 #define  SSB_IDLOW_INITP	0x0F000000 /* Initiator ports */
 #define  SSB_IDLOW_INITP_SHIFT	24
 #define  SSB_IDLOW_SSBREV	0xF0000000 /* Sonics Backplane Revision code */
 #define  SSB_IDLOW_SSBREV_22	0x00000000 /* <= 2.2 */
 #define  SSB_IDLOW_SSBREV_23	0x10000000 /* 2.3 */
 #define  SSB_IDLOW_SSBREV_24	0x40000000 /* ?? Found in BCM4328 */
 #define  SSB_IDLOW_SSBREV_25	0x50000000 /* ?? Not Found yet */
 #define  SSB_IDLOW_SSBREV_26	0x60000000 /* ?? Found in some BCM4311/2 */
 #define  SSB_IDLOW_SSBREV_27	0x70000000 /* ?? Found in some BCM4311/2 */
 #define SSB_IDHIGH		0x0FFC     /* SB Identification High */
 #define  SSB_IDHIGH_RCLO	0x0000000F /* Revision Code (low part) */
 #define  SSB_IDHIGH_CC		0x00008FF0 /* Core Code */
 #define  SSB_IDHIGH_CC_SHIFT	4
 #define  SSB_IDHIGH_RCHI	0x00007000 /* Revision Code (high part) */
 #define  SSB_IDHIGH_RCHI_SHIFT	8	   /* yes, shift 8 is right */
 #define  SSB_IDHIGH_VC		0xFFFF0000 /* Vendor Code */
 #define  SSB_IDHIGH_VC_SHIFT	16

 /* SPROM shadow area. If not otherwise noted, fields are
  * two bytes wide. Note that the SPROM can _only_ be read
  * in two-byte quantinies.
  */
 #define SSB_SPROMSIZE_WORDS		64
 #define SSB_SPROMSIZE_BYTES		(SSB_SPROMSIZE_WORDS * sizeof(u16))
 #define SSB_SPROMSIZE_WORDS_R123	64
 #define SSB_SPROMSIZE_WORDS_R4		220
 #define SSB_SPROMSIZE_BYTES_R123	(SSB_SPROMSIZE_WORDS_R123 * sizeof(u16))
 #define SSB_SPROMSIZE_BYTES_R4		(SSB_SPROMSIZE_WORDS_R4 * sizeof(u16))
 #define SSB_SPROM_BASE			0x1000
 #define SSB_SPROM_REVISION		0x107E
 #define  SSB_SPROM_REVISION_REV		0x00FF	/* SPROM Revision number */
 #define  SSB_SPROM_REVISION_CRC		0xFF00	/* SPROM CRC8 value */
 #define  SSB_SPROM_REVISION_CRC_SHIFT	8

 /* SPROM Revision 1 */
 #define SSB_SPROM1_SPID			0x1004	/* Subsystem Product ID for PCI */
 #define SSB_SPROM1_SVID			0x1006	/* Subsystem Vendor ID for PCI */
 #define SSB_SPROM1_PID			0x1008	/* Product ID for PCI */
 #define SSB_SPROM1_IL0MAC		0x1048	/* 6 bytes MAC address for 802.11b/g */
 #define SSB_SPROM1_ET0MAC		0x104E	/* 6 bytes MAC address for Ethernet */
 #define SSB_SPROM1_ET1MAC		0x1054	/* 6 bytes MAC address for 802.11a */
 #define SSB_SPROM1_ETHPHY		0x105A	/* Ethernet PHY settings */
 #define  SSB_SPROM1_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
 #define  SSB_SPROM1_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
 #define  SSB_SPROM1_ETHPHY_ET1A_SHIFT	5
 #define  SSB_SPROM1_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
 #define  SSB_SPROM1_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
 #define SSB_SPROM1_BINF			0x105C	/* Board info */
 #define  SSB_SPROM1_BINF_BREV		0x00FF	/* Board Revision */
 #define  SSB_SPROM1_BINF_CCODE		0x0F00	/* Country Code */
 #define  SSB_SPROM1_BINF_CCODE_SHIFT	8
 #define  SSB_SPROM1_BINF_ANTBG		0x3000	/* Available B-PHY and G-PHY antennas */
 #define  SSB_SPROM1_BINF_ANTBG_SHIFT	12
 #define  SSB_SPROM1_BINF_ANTA		0xC000	/* Available A-PHY antennas */
 #define  SSB_SPROM1_BINF_ANTA_SHIFT	14
 #define SSB_SPROM1_PA0B0		0x105E
 #define SSB_SPROM1_PA0B1		0x1060
 #define SSB_SPROM1_PA0B2		0x1062
 #define SSB_SPROM1_GPIOA		0x1064	/* General Purpose IO pins 0 and 1 */
 #define  SSB_SPROM1_GPIOA_P0		0x00FF	/* Pin 0 */
 #define  SSB_SPROM1_GPIOA_P1		0xFF00	/* Pin 1 */
 #define  SSB_SPROM1_GPIOA_P1_SHIFT	8
 #define SSB_SPROM1_GPIOB		0x1066	/* General Purpuse IO pins 2 and 3 */
 #define  SSB_SPROM1_GPIOB_P2		0x00FF	/* Pin 2 */
 #define  SSB_SPROM1_GPIOB_P3		0xFF00	/* Pin 3 */
 #define  SSB_SPROM1_GPIOB_P3_SHIFT	8
 #define SSB_SPROM1_MAXPWR		0x1068	/* Power Amplifier Max Power */
 #define  SSB_SPROM1_MAXPWR_BG		0x00FF	/* B-PHY and G-PHY (in dBm Q5.2) */
 #define  SSB_SPROM1_MAXPWR_A		0xFF00	/* A-PHY (in dBm Q5.2) */
 #define  SSB_SPROM1_MAXPWR_A_SHIFT	8
 #define SSB_SPROM1_PA1B0		0x106A
 #define SSB_SPROM1_PA1B1		0x106C
 #define SSB_SPROM1_PA1B2		0x106E
 #define SSB_SPROM1_ITSSI		0x1070	/* Idle TSSI Target */
 #define  SSB_SPROM1_ITSSI_BG		0x00FF	/* B-PHY and G-PHY*/
 #define  SSB_SPROM1_ITSSI_A		0xFF00	/* A-PHY */
 #define  SSB_SPROM1_ITSSI_A_SHIFT	8
 #define SSB_SPROM1_BFLLO		0x1072	/* Boardflags (low 16 bits) */
 #define SSB_SPROM1_AGAIN		0x1074	/* Antenna Gain (in dBm Q5.2) */
 #define  SSB_SPROM1_AGAIN_BG		0x00FF	/* B-PHY and G-PHY */
 #define  SSB_SPROM1_AGAIN_BG_SHIFT	0
 #define  SSB_SPROM1_AGAIN_A		0xFF00	/* A-PHY */
 #define  SSB_SPROM1_AGAIN_A_SHIFT	8

 /* SPROM Revision 2 (inherits from rev 1) */
 #define SSB_SPROM2_BFLHI		0x1038	/* Boardflags (high 16 bits) */
 #define SSB_SPROM2_MAXP_A		0x103A	/* A-PHY Max Power */
 #define  SSB_SPROM2_MAXP_A_HI		0x00FF	/* Max Power High */
 #define  SSB_SPROM2_MAXP_A_LO		0xFF00	/* Max Power Low */
 #define  SSB_SPROM2_MAXP_A_LO_SHIFT	8
 #define SSB_SPROM2_PA1LOB0		0x103C	/* A-PHY PowerAmplifier Low Settings */
 #define SSB_SPROM2_PA1LOB1		0x103E	/* A-PHY PowerAmplifier Low Settings */
 #define SSB_SPROM2_PA1LOB2		0x1040	/* A-PHY PowerAmplifier Low Settings */
 #define SSB_SPROM2_PA1HIB0		0x1042	/* A-PHY PowerAmplifier High Settings */
 #define SSB_SPROM2_PA1HIB1		0x1044	/* A-PHY PowerAmplifier High Settings */
 #define SSB_SPROM2_PA1HIB2		0x1046	/* A-PHY PowerAmplifier High Settings */
 #define SSB_SPROM2_OPO			0x1078	/* OFDM Power Offset from CCK Level */
 #define  SSB_SPROM2_OPO_VALUE		0x00FF
 #define  SSB_SPROM2_OPO_UNUSED		0xFF00
 #define SSB_SPROM2_CCODE		0x107C	/* Two char Country Code */

 /* SPROM Revision 3 (inherits most data from rev 2) */
 #define SSB_SPROM3_IL0MAC		0x104A	/* 6 bytes MAC address for 802.11b/g */
 #define SSB_SPROM3_OFDMAPO		0x102C	/* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
 #define SSB_SPROM3_OFDMALPO		0x1030	/* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
 #define SSB_SPROM3_OFDMAHPO		0x1034	/* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
 #define SSB_SPROM3_GPIOLDC		0x1042	/* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
 #define  SSB_SPROM3_GPIOLDC_OFF		0x0000FF00	/* Off Count */
 #define  SSB_SPROM3_GPIOLDC_OFF_SHIFT	8
 #define  SSB_SPROM3_GPIOLDC_ON		0x00FF0000	/* On Count */
 #define  SSB_SPROM3_GPIOLDC_ON_SHIFT	16
 #define SSB_SPROM3_CCKPO		0x1078	/* CCK Power Offset */
 #define  SSB_SPROM3_CCKPO_1M		0x000F	/* 1M Rate PO */
 #define  SSB_SPROM3_CCKPO_2M		0x00F0	/* 2M Rate PO */
 #define  SSB_SPROM3_CCKPO_2M_SHIFT	4
 #define  SSB_SPROM3_CCKPO_55M		0x0F00	/* 5.5M Rate PO */
 #define  SSB_SPROM3_CCKPO_55M_SHIFT	8
 #define  SSB_SPROM3_CCKPO_11M		0xF000	/* 11M Rate PO */
 #define  SSB_SPROM3_CCKPO_11M_SHIFT	12
 #define  SSB_SPROM3_OFDMGPO		0x107A	/* G-PHY OFDM Power Offset (4 bytes, BigEndian) */

 /* SPROM Revision 4 */
 #define SSB_SPROM4_IL0MAC		0x104C	/* 6 byte MAC address for a/b/g/n */
 #define SSB_SPROM4_ETHPHY		0x105A	/* Ethernet PHY settings ?? */
 #define  SSB_SPROM4_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
 #define  SSB_SPROM4_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
 #define  SSB_SPROM4_ETHPHY_ET1A_SHIFT	5
 #define  SSB_SPROM4_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
 #define  SSB_SPROM4_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
 #define SSB_SPROM4_CCODE		0x1052	/* Country Code (2 bytes) */
 #define SSB_SPROM4_ANTAVAIL		0x105D  /* Antenna available bitfields */
 #define SSB_SPROM4_ANTAVAIL_A		0x00FF	/* A-PHY bitfield */
 #define SSB_SPROM4_ANTAVAIL_A_SHIFT	0
 #define SSB_SPROM4_ANTAVAIL_BG		0xFF00	/* B-PHY and G-PHY bitfield */
 #define SSB_SPROM4_ANTAVAIL_BG_SHIFT	8
 #define SSB_SPROM4_BFLLO		0x1044	/* Boardflags (low 16 bits) */
 #define SSB_SPROM4_AGAIN01		0x105E	/* Antenna Gain (in dBm Q5.2) */
 #define  SSB_SPROM4_AGAIN0		0x00FF	/* Antenna 0 */
 #define  SSB_SPROM4_AGAIN0_SHIFT	0
 #define  SSB_SPROM4_AGAIN1		0xFF00	/* Antenna 1 */
 #define  SSB_SPROM4_AGAIN1_SHIFT	8
 #define SSB_SPROM4_AGAIN23		0x1060
 #define  SSB_SPROM4_AGAIN2		0x00FF	/* Antenna 2 */
 #define  SSB_SPROM4_AGAIN2_SHIFT	0
 #define  SSB_SPROM4_AGAIN3		0xFF00	/* Antenna 3 */
 #define  SSB_SPROM4_AGAIN3_SHIFT	8
 #define SSB_SPROM4_BFLHI		0x1046  /* Board Flags Hi */
 #define SSB_SPROM4_MAXP_BG		0x1080  /* Max Power BG in path 1 */
 #define  SSB_SPROM4_MAXP_BG_MASK	0x00FF  /* Mask for Max Power BG */
 #define  SSB_SPROM4_ITSSI_BG		0xFF00	/* Mask for path 1 itssi_bg */
 #define  SSB_SPROM4_ITSSI_BG_SHIFT	8
 #define SSB_SPROM4_MAXP_A		0x108A  /* Max Power A in path 1 */
 #define  SSB_SPROM4_MAXP_A_MASK		0x00FF  /* Mask for Max Power A */
 #define  SSB_SPROM4_ITSSI_A		0xFF00	/* Mask for path 1 itssi_a */
 #define  SSB_SPROM4_ITSSI_A_SHIFT	8
 #define SSB_SPROM4_GPIOA		0x1056	/* Gen. Purpose IO # 0 and 1 */
 #define  SSB_SPROM4_GPIOA_P0		0x00FF	/* Pin 0 */
 #define  SSB_SPROM4_GPIOA_P1		0xFF00	/* Pin 1 */
 #define  SSB_SPROM4_GPIOA_P1_SHIFT	8
 #define SSB_SPROM4_GPIOB		0x1058	/* Gen. Purpose IO # 2 and 3 */
 #define  SSB_SPROM4_GPIOB_P2		0x00FF	/* Pin 2 */
 #define  SSB_SPROM4_GPIOB_P3		0xFF00	/* Pin 3 */
 #define  SSB_SPROM4_GPIOB_P3_SHIFT	8
 #define SSB_SPROM4_PA0B0		0x1082	/* The paXbY locations are */
 #define SSB_SPROM4_PA0B1		0x1084	/*   only guesses */
 #define SSB_SPROM4_PA0B2		0x1086
 #define SSB_SPROM4_PA1B0		0x108E
 #define SSB_SPROM4_PA1B1		0x1090
 #define SSB_SPROM4_PA1B2		0x1092

 /* SPROM Revision 5 (inherits most data from rev 4) */
 #define SSB_SPROM5_BFLLO		0x104A	/* Boardflags (low 16 bits) */
 #define SSB_SPROM5_BFLHI		0x104C  /* Board Flags Hi */
 #define SSB_SPROM5_IL0MAC		0x1052	/* 6 byte MAC address for a/b/g/n */
 #define SSB_SPROM5_CCODE		0x1044	/* Country Code (2 bytes) */
 #define SSB_SPROM5_GPIOA		0x1076	/* Gen. Purpose IO # 0 and 1 */
 #define  SSB_SPROM5_GPIOA_P0		0x00FF	/* Pin 0 */
 #define  SSB_SPROM5_GPIOA_P1		0xFF00	/* Pin 1 */
 #define  SSB_SPROM5_GPIOA_P1_SHIFT	8
 #define SSB_SPROM5_GPIOB		0x1078	/* Gen. Purpose IO # 2 and 3 */
 #define  SSB_SPROM5_GPIOB_P2		0x00FF	/* Pin 2 */
 #define  SSB_SPROM5_GPIOB_P3		0xFF00	/* Pin 3 */
 #define  SSB_SPROM5_GPIOB_P3_SHIFT	8


 /* Values for SSB_SPROM1_BINF_CCODE */
 enum {
 	SSB_SPROM1CCODE_WORLD = 0,
 	SSB_SPROM1CCODE_THAILAND,
 	SSB_SPROM1CCODE_ISRAEL,
 	SSB_SPROM1CCODE_JORDAN,
 	SSB_SPROM1CCODE_CHINA,
 	SSB_SPROM1CCODE_JAPAN,
 	SSB_SPROM1CCODE_USA_CANADA_ANZ,
 	SSB_SPROM1CCODE_EUROPE,
 	SSB_SPROM1CCODE_USA_LOW,
 	SSB_SPROM1CCODE_JAPAN_HIGH,
 	SSB_SPROM1CCODE_ALL,
 	SSB_SPROM1CCODE_NONE,
 };

 /* Address-Match values and masks (SSB_ADMATCHxxx) */
 #define SSB_ADM_TYPE			0x00000003	/* Address type */
 #define  SSB_ADM_TYPE0			0
 #define  SSB_ADM_TYPE1			1
 #define  SSB_ADM_TYPE2			2
 #define SSB_ADM_AD64			0x00000004
 #define SSB_ADM_SZ0			0x000000F8	/* Type0 size */
 #define SSB_ADM_SZ0_SHIFT		3
 #define SSB_ADM_SZ1			0x000001F8	/* Type1 size */
 #define SSB_ADM_SZ1_SHIFT		3
 #define SSB_ADM_SZ2			0x000001F8	/* Type2 size */
 #define SSB_ADM_SZ2_SHIFT		3
 #define SSB_ADM_EN			0x00000400	/* Enable */
 #define SSB_ADM_NEG			0x00000800	/* Negative decode */
 #define SSB_ADM_BASE0			0xFFFFFF00	/* Type0 base address */
 #define SSB_ADM_BASE0_SHIFT		8
 #define SSB_ADM_BASE1			0xFFFFF000	/* Type1 base address for the core */
 #define SSB_ADM_BASE1_SHIFT		12
 #define SSB_ADM_BASE2			0xFFFF0000	/* Type2 base address for the core */
 #define SSB_ADM_BASE2_SHIFT		16


 #endif /* LINUX_SSB_REGS_H_ */
	#ifndef LINUX_SSB_REGS_H_
	#define LINUX_SSB_REGS_H_


	/* SiliconBackplane Address Map.
	* All regions may not exist on all chips.
	*/
	#define SSB_SDRAM_BASE 0x00000000U /* Physical SDRAM */
	#define SSB_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */
	#define SSB_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */
	#define SSB_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */
	#define SSB_ENUM_BASE 0x18000000U /* Enumeration space base */
	#define SSB_ENUM_LIMIT 0x18010000U /* Enumeration space limit */

	#define SSB_FLASH2 0x1c000000U /* Flash Region 2 (region 1 shadowed here) */
	#define SSB_FLASH2_SZ 0x02000000U /* Size of Flash Region 2 */

	#define SSB_EXTIF_BASE 0x1f000000U /* External Interface region base address */
	#define SSB_FLASH1 0x1fc00000U /* Flash Region 1 */
	#define SSB_FLASH1_SZ 0x00400000U /* Size of Flash Region 1 */

	#define SSB_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */
	#define SSB_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */
	#define SSB_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */
	#define SSB_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */
	#define SSB_EUART (SSB_EXTIF_BASE + 0x00800000)
	#define SSB_LED (SSB_EXTIF_BASE + 0x00900000)


	/* Enumeration space constants */
	#define SSB_CORE_SIZE 0x1000 /* Size of a core MMIO area */
	#define SSB_MAX_NR_CORES ((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE)


	/* mips address */
	#define SSB_EJTAG 0xff200000 /* MIPS EJTAG space (2M) */


	/* SSB PCI config space registers. */
	#define SSB_PMCSR 0x44
	#define SSB_PE 0x100
	#define SSB_BAR0_WIN 0x80 /* Backplane address space 0 */
	#define SSB_BAR1_WIN 0x84 /* Backplane address space 1 */
	#define SSB_SPROMCTL 0x88 /* SPROM control */
	#define SSB_SPROMCTL_WE 0x10 /* SPROM write enable */
	#define SSB_BAR1_CONTROL 0x8c /* Address space 1 burst control */
	#define SSB_PCI_IRQS 0x90 /* PCI interrupts */
	#define SSB_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */
	#define SSB_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */
	#define SSB_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */
	#define SSB_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */
	#define SSB_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */
	#define SSB_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */
	#define SSB_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */
	#define SSB_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */
	#define SSB_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */


	#define SSB_BAR0_MAX_RETRIES 50

	/* Silicon backplane configuration register definitions */
	#define SSB_IPSFLAG 0x0F08
	#define SSB_IPSFLAG_IRQ1 0x0000003F /* which sbflags get routed to mips interrupt 1 */
	#define SSB_IPSFLAG_IRQ1_SHIFT 0
	#define SSB_IPSFLAG_IRQ2 0x00003F00 /* which sbflags get routed to mips interrupt 2 */
	#define SSB_IPSFLAG_IRQ2_SHIFT 8
	#define SSB_IPSFLAG_IRQ3 0x003F0000 /* which sbflags get routed to mips interrupt 3 */
	#define SSB_IPSFLAG_IRQ3_SHIFT 16
	#define SSB_IPSFLAG_IRQ4 0x3F000000 /* which sbflags get routed to mips interrupt 4 */
	#define SSB_IPSFLAG_IRQ4_SHIFT 24
	#define SSB_TPSFLAG 0x0F18
	#define SSB_TPSFLAG_BPFLAG 0x0000003F /* Backplane flag # */
	#define SSB_TPSFLAG_ALWAYSIRQ 0x00000040 /* IRQ is always sent on the Backplane */
	#define SSB_TMERRLOGA 0x0F48
	#define SSB_TMERRLOG 0x0F50
	#define SSB_ADMATCH3 0x0F60
	#define SSB_ADMATCH2 0x0F68
	#define SSB_ADMATCH1 0x0F70
	#define SSB_IMSTATE 0x0F90 /* SB Initiator Agent State */
	#define SSB_IMSTATE_PC 0x0000000f /* Pipe Count */
	#define SSB_IMSTATE_AP_MASK 0x00000030 /* Arbitration Priority */
	#define SSB_IMSTATE_AP_BOTH 0x00000000 /* Use both timeslices and token */
	#define SSB_IMSTATE_AP_TS 0x00000010 /* Use timeslices only */
	#define SSB_IMSTATE_AP_TK 0x00000020 /* Use token only */
	#define SSB_IMSTATE_AP_RSV 0x00000030 /* Reserved */
	#define SSB_IMSTATE_IBE 0x00020000 /* In Band Error */
	#define SSB_IMSTATE_TO 0x00040000 /* Timeout */
	#define SSB_INTVEC 0x0F94 /* SB Interrupt Mask */
	#define SSB_INTVEC_PCI 0x00000001 /* Enable interrupts for PCI */
	#define SSB_INTVEC_ENET0 0x00000002 /* Enable interrupts for enet 0 */
	#define SSB_INTVEC_ILINE20 0x00000004 /* Enable interrupts for iline20 */
	#define SSB_INTVEC_CODEC 0x00000008 /* Enable interrupts for v90 codec */
	#define SSB_INTVEC_USB 0x00000010 /* Enable interrupts for usb */
	#define SSB_INTVEC_EXTIF 0x00000020 /* Enable interrupts for external i/f */
	#define SSB_INTVEC_ENET1 0x00000040 /* Enable interrupts for enet 1 */
	#define SSB_TMSLOW 0x0F98 /* SB Target State Low */
	#define SSB_TMSLOW_RESET 0x00000001 /* Reset */
	#define SSB_TMSLOW_REJECT_22 0x00000002 /* Reject (Backplane rev 2.2) */
	#define SSB_TMSLOW_REJECT_23 0x00000004 /* Reject (Backplane rev 2.3) */
	#define SSB_TMSLOW_CLOCK 0x00010000 /* Clock Enable */
	#define SSB_TMSLOW_FGC 0x00020000 /* Force Gated Clocks On */
	#define SSB_TMSLOW_PE 0x40000000 /* Power Management Enable */
	#define SSB_TMSLOW_BE 0x80000000 /* BIST Enable */
	#define SSB_TMSHIGH 0x0F9C /* SB Target State High */
	#define SSB_TMSHIGH_SERR 0x00000001 /* S-error */
	#define SSB_TMSHIGH_INT 0x00000002 /* Interrupt */
	#define SSB_TMSHIGH_BUSY 0x00000004 /* Busy */
	#define SSB_TMSHIGH_TO 0x00000020 /* Timeout. Backplane rev >= 2.3 only */
	#define SSB_TMSHIGH_COREFL 0x1FFF0000 /* Core specific flags */
	#define SSB_TMSHIGH_COREFL_SHIFT 16
	#define SSB_TMSHIGH_DMA64 0x10000000 /* 64bit DMA supported */
	#define SSB_TMSHIGH_GCR 0x20000000 /* Gated Clock Request */
	#define SSB_TMSHIGH_BISTF 0x40000000 /* BIST Failed */
	#define SSB_TMSHIGH_BISTD 0x80000000 /* BIST Done */
	#define SSB_BWA0 0x0FA0
	#define SSB_IMCFGLO 0x0FA8
	#define SSB_IMCFGLO_SERTO 0x00000007 /* Service timeout */
	#define SSB_IMCFGLO_REQTO 0x00000070 /* Request timeout */
	#define SSB_IMCFGLO_REQTO_SHIFT 4
	#define SSB_IMCFGLO_CONNID 0x00FF0000 /* Connection ID */
	#define SSB_IMCFGLO_CONNID_SHIFT 16
	#define SSB_IMCFGHI 0x0FAC
	#define SSB_ADMATCH0 0x0FB0
	#define SSB_TMCFGLO 0x0FB8
	#define SSB_TMCFGHI 0x0FBC
	#define SSB_BCONFIG 0x0FC0
	#define SSB_BSTATE 0x0FC8
	#define SSB_ACTCFG 0x0FD8
	#define SSB_FLAGST 0x0FE8
	#define SSB_IDLOW 0x0FF8
	#define SSB_IDLOW_CFGSP 0x00000003 /* Config Space */
	#define SSB_IDLOW_ADDRNGE 0x00000038 /* Address Ranges supported */
	#define SSB_IDLOW_ADDRNGE_SHIFT 3
	#define SSB_IDLOW_SYNC 0x00000040
	#define SSB_IDLOW_INITIATOR 0x00000080
	#define SSB_IDLOW_MIBL 0x00000F00 /* Minimum Backplane latency */
	#define SSB_IDLOW_MIBL_SHIFT 8
	#define SSB_IDLOW_MABL 0x0000F000 /* Maximum Backplane latency */
	#define SSB_IDLOW_MABL_SHIFT 12
	#define SSB_IDLOW_TIF 0x00010000 /* This Initiator is first */
	#define SSB_IDLOW_CCW 0x000C0000 /* Cycle counter width */
	#define SSB_IDLOW_CCW_SHIFT 18
	#define SSB_IDLOW_TPT 0x00F00000 /* Target ports */
	#define SSB_IDLOW_TPT_SHIFT 20
	#define SSB_IDLOW_INITP 0x0F000000 /* Initiator ports */
	#define SSB_IDLOW_INITP_SHIFT 24
	#define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */
	#define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */
	#define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */
	#define SSB_IDLOW_SSBREV_24 0x40000000 /* ?? Found in BCM4328 */
	#define SSB_IDLOW_SSBREV_25 0x50000000 /* ?? Not Found yet */
	#define SSB_IDLOW_SSBREV_26 0x60000000 /* ?? Found in some BCM4311/2 */
	#define SSB_IDLOW_SSBREV_27 0x70000000 /* ?? Found in some BCM4311/2 */
	#define SSB_IDHIGH 0x0FFC /* SB Identification High */
	#define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */
	#define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */
	#define SSB_IDHIGH_CC_SHIFT 4
	#define SSB_IDHIGH_RCHI 0x00007000 /* Revision Code (high part) */
	#define SSB_IDHIGH_RCHI_SHIFT 8 /* yes, shift 8 is right */
	#define SSB_IDHIGH_VC 0xFFFF0000 /* Vendor Code */
	#define SSB_IDHIGH_VC_SHIFT 16

	/* SPROM shadow area. If not otherwise noted, fields are
	* two bytes wide. Note that the SPROM can _only_ be read
	* in two-byte quantinies.
	*/
	#define SSB_SPROMSIZE_WORDS 64
	#define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16))
	#define SSB_SPROMSIZE_WORDS_R123 64
	#define SSB_SPROMSIZE_WORDS_R4 220
	#define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16))
	#define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16))
	#define SSB_SPROM_BASE 0x1000
	#define SSB_SPROM_REVISION 0x107E
	#define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */
	#define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */
	#define SSB_SPROM_REVISION_CRC_SHIFT 8

	/* SPROM Revision 1 */
	#define SSB_SPROM1_SPID 0x1004 /* Subsystem Product ID for PCI */
	#define SSB_SPROM1_SVID 0x1006 /* Subsystem Vendor ID for PCI */
	#define SSB_SPROM1_PID 0x1008 /* Product ID for PCI */
	#define SSB_SPROM1_IL0MAC 0x1048 /* 6 bytes MAC address for 802.11b/g */
	#define SSB_SPROM1_ET0MAC 0x104E /* 6 bytes MAC address for Ethernet */
	#define SSB_SPROM1_ET1MAC 0x1054 /* 6 bytes MAC address for 802.11a */
	#define SSB_SPROM1_ETHPHY 0x105A /* Ethernet PHY settings */
	#define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
	#define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
	#define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5
	#define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
	#define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
	#define SSB_SPROM1_BINF 0x105C /* Board info */
	#define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */
	#define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */
	#define SSB_SPROM1_BINF_CCODE_SHIFT 8
	#define SSB_SPROM1_BINF_ANTBG 0x3000 /* Available B-PHY and G-PHY antennas */
	#define SSB_SPROM1_BINF_ANTBG_SHIFT 12
	#define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */
	#define SSB_SPROM1_BINF_ANTA_SHIFT 14
	#define SSB_SPROM1_PA0B0 0x105E
	#define SSB_SPROM1_PA0B1 0x1060
	#define SSB_SPROM1_PA0B2 0x1062
	#define SSB_SPROM1_GPIOA 0x1064 /* General Purpose IO pins 0 and 1 */
	#define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */
	#define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */
	#define SSB_SPROM1_GPIOA_P1_SHIFT 8
	#define SSB_SPROM1_GPIOB 0x1066 /* General Purpuse IO pins 2 and 3 */
	#define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */
	#define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */
	#define SSB_SPROM1_GPIOB_P3_SHIFT 8
	#define SSB_SPROM1_MAXPWR 0x1068 /* Power Amplifier Max Power */
	#define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */
	#define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */
	#define SSB_SPROM1_MAXPWR_A_SHIFT 8
	#define SSB_SPROM1_PA1B0 0x106A
	#define SSB_SPROM1_PA1B1 0x106C
	#define SSB_SPROM1_PA1B2 0x106E
	#define SSB_SPROM1_ITSSI 0x1070 /* Idle TSSI Target */
	#define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/
	#define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */
	#define SSB_SPROM1_ITSSI_A_SHIFT 8
	#define SSB_SPROM1_BFLLO 0x1072 /* Boardflags (low 16 bits) */
	#define SSB_SPROM1_AGAIN 0x1074 /* Antenna Gain (in dBm Q5.2) */
	#define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */
	#define SSB_SPROM1_AGAIN_BG_SHIFT 0
	#define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */
	#define SSB_SPROM1_AGAIN_A_SHIFT 8

	/* SPROM Revision 2 (inherits from rev 1) */
	#define SSB_SPROM2_BFLHI 0x1038 /* Boardflags (high 16 bits) */
	#define SSB_SPROM2_MAXP_A 0x103A /* A-PHY Max Power */
	#define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */
	#define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */
	#define SSB_SPROM2_MAXP_A_LO_SHIFT 8
	#define SSB_SPROM2_PA1LOB0 0x103C /* A-PHY PowerAmplifier Low Settings */
	#define SSB_SPROM2_PA1LOB1 0x103E /* A-PHY PowerAmplifier Low Settings */
	#define SSB_SPROM2_PA1LOB2 0x1040 /* A-PHY PowerAmplifier Low Settings */
	#define SSB_SPROM2_PA1HIB0 0x1042 /* A-PHY PowerAmplifier High Settings */
	#define SSB_SPROM2_PA1HIB1 0x1044 /* A-PHY PowerAmplifier High Settings */
	#define SSB_SPROM2_PA1HIB2 0x1046 /* A-PHY PowerAmplifier High Settings */
	#define SSB_SPROM2_OPO 0x1078 /* OFDM Power Offset from CCK Level */
	#define SSB_SPROM2_OPO_VALUE 0x00FF
	#define SSB_SPROM2_OPO_UNUSED 0xFF00
	#define SSB_SPROM2_CCODE 0x107C /* Two char Country Code */

	/* SPROM Revision 3 (inherits most data from rev 2) */
	#define SSB_SPROM3_IL0MAC 0x104A /* 6 bytes MAC address for 802.11b/g */
	#define SSB_SPROM3_OFDMAPO 0x102C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
	#define SSB_SPROM3_OFDMALPO 0x1030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
	#define SSB_SPROM3_OFDMAHPO 0x1034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
	#define SSB_SPROM3_GPIOLDC 0x1042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
	#define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */
	#define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8
	#define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */
	#define SSB_SPROM3_GPIOLDC_ON_SHIFT 16
	#define SSB_SPROM3_CCKPO 0x1078 /* CCK Power Offset */
	#define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */
	#define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */
	#define SSB_SPROM3_CCKPO_2M_SHIFT 4
	#define SSB_SPROM3_CCKPO_55M 0x0F00 /* 5.5M Rate PO */
	#define SSB_SPROM3_CCKPO_55M_SHIFT 8
	#define SSB_SPROM3_CCKPO_11M 0xF000 /* 11M Rate PO */
	#define SSB_SPROM3_CCKPO_11M_SHIFT 12
	#define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */

	/* SPROM Revision 4 */
	#define SSB_SPROM4_IL0MAC 0x104C /* 6 byte MAC address for a/b/g/n */
	#define SSB_SPROM4_ETHPHY 0x105A /* Ethernet PHY settings ?? */
	#define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */
	#define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */
	#define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5
	#define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */
	#define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */
	#define SSB_SPROM4_CCODE 0x1052 /* Country Code (2 bytes) */
	#define SSB_SPROM4_ANTAVAIL 0x105D /* Antenna available bitfields */
	#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */
	#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0
	#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */
	#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8
	#define SSB_SPROM4_BFLLO 0x1044 /* Boardflags (low 16 bits) */
	#define SSB_SPROM4_AGAIN01 0x105E /* Antenna Gain (in dBm Q5.2) */
	#define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */
	#define SSB_SPROM4_AGAIN0_SHIFT 0
	#define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */
	#define SSB_SPROM4_AGAIN1_SHIFT 8
	#define SSB_SPROM4_AGAIN23 0x1060
	#define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */
	#define SSB_SPROM4_AGAIN2_SHIFT 0
	#define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */
	#define SSB_SPROM4_AGAIN3_SHIFT 8
	#define SSB_SPROM4_BFLHI 0x1046 /* Board Flags Hi */
	#define SSB_SPROM4_MAXP_BG 0x1080 /* Max Power BG in path 1 */
	#define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */
	#define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */
	#define SSB_SPROM4_ITSSI_BG_SHIFT 8
	#define SSB_SPROM4_MAXP_A 0x108A /* Max Power A in path 1 */
	#define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */
	#define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */
	#define SSB_SPROM4_ITSSI_A_SHIFT 8
	#define SSB_SPROM4_GPIOA 0x1056 /* Gen. Purpose IO # 0 and 1 */
	#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */
	#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */
	#define SSB_SPROM4_GPIOA_P1_SHIFT 8
	#define SSB_SPROM4_GPIOB 0x1058 /* Gen. Purpose IO # 2 and 3 */
	#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */
	#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */
	#define SSB_SPROM4_GPIOB_P3_SHIFT 8
	#define SSB_SPROM4_PA0B0 0x1082 /* The paXbY locations are */
	#define SSB_SPROM4_PA0B1 0x1084 /* only guesses */
	#define SSB_SPROM4_PA0B2 0x1086
	#define SSB_SPROM4_PA1B0 0x108E
	#define SSB_SPROM4_PA1B1 0x1090
	#define SSB_SPROM4_PA1B2 0x1092

	/* SPROM Revision 5 (inherits most data from rev 4) */
	#define SSB_SPROM5_BFLLO 0x104A /* Boardflags (low 16 bits) */
	#define SSB_SPROM5_BFLHI 0x104C /* Board Flags Hi */
	#define SSB_SPROM5_IL0MAC 0x1052 /* 6 byte MAC address for a/b/g/n */
	#define SSB_SPROM5_CCODE 0x1044 /* Country Code (2 bytes) */
	#define SSB_SPROM5_GPIOA 0x1076 /* Gen. Purpose IO # 0 and 1 */
	#define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */
	#define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */
	#define SSB_SPROM5_GPIOA_P1_SHIFT 8
	#define SSB_SPROM5_GPIOB 0x1078 /* Gen. Purpose IO # 2 and 3 */
	#define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */
	#define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */
	#define SSB_SPROM5_GPIOB_P3_SHIFT 8


	/* Values for SSB_SPROM1_BINF_CCODE */
	enum {
	SSB_SPROM1CCODE_WORLD = 0,
	SSB_SPROM1CCODE_THAILAND,
	SSB_SPROM1CCODE_ISRAEL,
	SSB_SPROM1CCODE_JORDAN,
	SSB_SPROM1CCODE_CHINA,
	SSB_SPROM1CCODE_JAPAN,
	SSB_SPROM1CCODE_USA_CANADA_ANZ,
	SSB_SPROM1CCODE_EUROPE,
	SSB_SPROM1CCODE_USA_LOW,
	SSB_SPROM1CCODE_JAPAN_HIGH,
	SSB_SPROM1CCODE_ALL,
	SSB_SPROM1CCODE_NONE,
	};

	/* Address-Match values and masks (SSB_ADMATCHxxx) */
	#define SSB_ADM_TYPE 0x00000003 /* Address type */
	#define SSB_ADM_TYPE0 0
	#define SSB_ADM_TYPE1 1
	#define SSB_ADM_TYPE2 2
	#define SSB_ADM_AD64 0x00000004
	#define SSB_ADM_SZ0 0x000000F8 /* Type0 size */
	#define SSB_ADM_SZ0_SHIFT 3
	#define SSB_ADM_SZ1 0x000001F8 /* Type1 size */
	#define SSB_ADM_SZ1_SHIFT 3
	#define SSB_ADM_SZ2 0x000001F8 /* Type2 size */
	#define SSB_ADM_SZ2_SHIFT 3
	#define SSB_ADM_EN 0x00000400 /* Enable */
	#define SSB_ADM_NEG 0x00000800 /* Negative decode */
	#define SSB_ADM_BASE0 0xFFFFFF00 /* Type0 base address */
	#define SSB_ADM_BASE0_SHIFT 8
	#define SSB_ADM_BASE1 0xFFFFF000 /* Type1 base address for the core */
	#define SSB_ADM_BASE1_SHIFT 12
	#define SSB_ADM_BASE2 0xFFFF0000 /* Type2 base address for the core */
	#define SSB_ADM_BASE2_SHIFT 16


	#endif /* LINUX_SSB_REGS_H_ */