| /* |
| * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/pinctrl/omap.h> |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| compatible = "ti,omap4430", "ti,omap4"; |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| next-level-cache = <&L2>; |
| reg = <0x0>; |
| |
| clocks = <&dpll_mpu_ck>; |
| clock-names = "cpu"; |
| |
| clock-latency = <300000>; /* From omap-cpufreq driver */ |
| }; |
| cpu@1 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| next-level-cache = <&L2>; |
| reg = <0x1>; |
| }; |
| }; |
| |
| gic: interrupt-controller@48241000 { |
| compatible = "arm,cortex-a9-gic"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x48241000 0x1000>, |
| <0x48240100 0x0100>; |
| }; |
| |
| L2: l2-cache-controller@48242000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x48242000 0x1000>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| local-timer@48240600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x48240600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| /* |
| * The soc node represents the soc top level view. It is uses for IPs |
| * that are not memory mapped in the MPU view or for the MPU itself. |
| */ |
| soc { |
| compatible = "ti,omap-infra"; |
| mpu { |
| compatible = "ti,omap4-mpu"; |
| ti,hwmods = "mpu"; |
| }; |
| |
| dsp { |
| compatible = "ti,omap3-c64"; |
| ti,hwmods = "dsp"; |
| }; |
| |
| iva { |
| compatible = "ti,ivahd"; |
| ti,hwmods = "iva"; |
| }; |
| }; |
| |
| /* |
| * XXX: Use a flat representation of the OMAP4 interconnect. |
| * The real OMAP interconnect network is quite complex. |
| * Since that will not bring real advantage to represent that in DT for |
| * the moment, just use a fake OCP bus entry to represent the whole bus |
| * hierarchy. |
| */ |
| ocp { |
| compatible = "ti,omap4-l3-noc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; |
| reg = <0x44000000 0x1000>, |
| <0x44800000 0x2000>, |
| <0x45000000 0x1000>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| |
| cm1: cm1@4a004000 { |
| compatible = "ti,omap4-cm1"; |
| reg = <0x4a004000 0x2000>; |
| |
| cm1_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| cm1_clockdomains: clockdomains { |
| }; |
| }; |
| |
| prm: prm@4a306000 { |
| compatible = "ti,omap4-prm"; |
| reg = <0x4a306000 0x3000>; |
| |
| prm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| prm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| cm2: cm2@4a008000 { |
| compatible = "ti,omap4-cm2"; |
| reg = <0x4a008000 0x3000>; |
| |
| cm2_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| cm2_clockdomains: clockdomains { |
| }; |
| }; |
| |
| scrm: scrm@4a30a000 { |
| compatible = "ti,omap4-scrm"; |
| reg = <0x4a30a000 0x2000>; |
| |
| scrm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| scrm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| counter32k: counter@4a304000 { |
| compatible = "ti,omap-counter32k"; |
| reg = <0x4a304000 0x20>; |
| ti,hwmods = "counter_32k"; |
| }; |
| |
| omap4_pmx_core: pinmux@4a100040 { |
| compatible = "ti,omap4-padconf", "pinctrl-single"; |
| reg = <0x4a100040 0x0196>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <16>; |
| pinctrl-single,function-mask = <0x7fff>; |
| }; |
| omap4_pmx_wkup: pinmux@4a31e040 { |
| compatible = "ti,omap4-padconf", "pinctrl-single"; |
| reg = <0x4a31e040 0x0038>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <16>; |
| pinctrl-single,function-mask = <0x7fff>; |
| }; |
| |
| omap4_padconf_global: tisyscon@4a1005a0 { |
| compatible = "syscon"; |
| reg = <0x4a1005a0 0x170>; |
| }; |
| |
| pbias_regulator: pbias_regulator { |
| compatible = "ti,pbias-omap"; |
| reg = <0x60 0x4>; |
| syscon = <&omap4_padconf_global>; |
| pbias_mmc_reg: pbias_mmc_omap4 { |
| regulator-name = "pbias_mmc_omap4"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| }; |
| |
| sdma: dma-controller@4a056000 { |
| compatible = "ti,omap4430-sdma"; |
| reg = <0x4a056000 0x1000>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| #dma-channels = <32>; |
| #dma-requests = <127>; |
| }; |
| |
| gpio1: gpio@4a310000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x4a310000 0x200>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio1"; |
| ti,gpio-always-on; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@48055000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x48055000 0x200>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio2"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@48057000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x48057000 0x200>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio3"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@48059000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x48059000 0x200>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio4"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@4805b000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x4805b000 0x200>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio5"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@4805d000 { |
| compatible = "ti,omap4-gpio"; |
| reg = <0x4805d000 0x200>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "gpio6"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpmc: gpmc@50000000 { |
| compatible = "ti,omap4430-gpmc"; |
| reg = <0x50000000 0x1000>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| gpmc,num-cs = <8>; |
| gpmc,num-waitpins = <4>; |
| ti,hwmods = "gpmc"; |
| ti,no-idle-on-init; |
| clocks = <&l3_div_ck>; |
| clock-names = "fck"; |
| }; |
| |
| uart1: serial@4806a000 { |
| compatible = "ti,omap4-uart"; |
| reg = <0x4806a000 0x100>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart1"; |
| clock-frequency = <48000000>; |
| }; |
| |
| uart2: serial@4806c000 { |
| compatible = "ti,omap4-uart"; |
| reg = <0x4806c000 0x100>; |
| interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart2"; |
| clock-frequency = <48000000>; |
| }; |
| |
| uart3: serial@48020000 { |
| compatible = "ti,omap4-uart"; |
| reg = <0x48020000 0x100>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart3"; |
| clock-frequency = <48000000>; |
| }; |
| |
| uart4: serial@4806e000 { |
| compatible = "ti,omap4-uart"; |
| reg = <0x4806e000 0x100>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart4"; |
| clock-frequency = <48000000>; |
| }; |
| |
| hwspinlock: spinlock@4a0f6000 { |
| compatible = "ti,omap4-hwspinlock"; |
| reg = <0x4a0f6000 0x1000>; |
| ti,hwmods = "spinlock"; |
| #hwlock-cells = <1>; |
| }; |
| |
| i2c1: i2c@48070000 { |
| compatible = "ti,omap4-i2c"; |
| reg = <0x48070000 0x100>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c1"; |
| }; |
| |
| i2c2: i2c@48072000 { |
| compatible = "ti,omap4-i2c"; |
| reg = <0x48072000 0x100>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c2"; |
| }; |
| |
| i2c3: i2c@48060000 { |
| compatible = "ti,omap4-i2c"; |
| reg = <0x48060000 0x100>; |
| interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c3"; |
| }; |
| |
| i2c4: i2c@48350000 { |
| compatible = "ti,omap4-i2c"; |
| reg = <0x48350000 0x100>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "i2c4"; |
| }; |
| |
| mcspi1: spi@48098000 { |
| compatible = "ti,omap4-mcspi"; |
| reg = <0x48098000 0x200>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi1"; |
| ti,spi-num-cs = <4>; |
| dmas = <&sdma 35>, |
| <&sdma 36>, |
| <&sdma 37>, |
| <&sdma 38>, |
| <&sdma 39>, |
| <&sdma 40>, |
| <&sdma 41>, |
| <&sdma 42>; |
| dma-names = "tx0", "rx0", "tx1", "rx1", |
| "tx2", "rx2", "tx3", "rx3"; |
| }; |
| |
| mcspi2: spi@4809a000 { |
| compatible = "ti,omap4-mcspi"; |
| reg = <0x4809a000 0x200>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi2"; |
| ti,spi-num-cs = <2>; |
| dmas = <&sdma 43>, |
| <&sdma 44>, |
| <&sdma 45>, |
| <&sdma 46>; |
| dma-names = "tx0", "rx0", "tx1", "rx1"; |
| }; |
| |
| mcspi3: spi@480b8000 { |
| compatible = "ti,omap4-mcspi"; |
| reg = <0x480b8000 0x200>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi3"; |
| ti,spi-num-cs = <2>; |
| dmas = <&sdma 15>, <&sdma 16>; |
| dma-names = "tx0", "rx0"; |
| }; |
| |
| mcspi4: spi@480ba000 { |
| compatible = "ti,omap4-mcspi"; |
| reg = <0x480ba000 0x200>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "mcspi4"; |
| ti,spi-num-cs = <1>; |
| dmas = <&sdma 70>, <&sdma 71>; |
| dma-names = "tx0", "rx0"; |
| }; |
| |
| mmc1: mmc@4809c000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x4809c000 0x400>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmc1"; |
| ti,dual-volt; |
| ti,needs-special-reset; |
| dmas = <&sdma 61>, <&sdma 62>; |
| dma-names = "tx", "rx"; |
| pbias-supply = <&pbias_mmc_reg>; |
| }; |
| |
| mmc2: mmc@480b4000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x480b4000 0x400>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmc2"; |
| ti,needs-special-reset; |
| dmas = <&sdma 47>, <&sdma 48>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmc3: mmc@480ad000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x480ad000 0x400>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmc3"; |
| ti,needs-special-reset; |
| dmas = <&sdma 77>, <&sdma 78>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmc4: mmc@480d1000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x480d1000 0x400>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmc4"; |
| ti,needs-special-reset; |
| dmas = <&sdma 57>, <&sdma 58>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmc5: mmc@480d5000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x480d5000 0x400>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmc5"; |
| ti,needs-special-reset; |
| dmas = <&sdma 59>, <&sdma 60>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mmu_dsp: mmu@4a066000 { |
| compatible = "ti,omap4-iommu"; |
| reg = <0x4a066000 0x100>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmu_dsp"; |
| }; |
| |
| mmu_ipu: mmu@55082000 { |
| compatible = "ti,omap4-iommu"; |
| reg = <0x55082000 0x100>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mmu_ipu"; |
| ti,iommu-bus-err-back; |
| }; |
| |
| wdt2: wdt@4a314000 { |
| compatible = "ti,omap4-wdt", "ti,omap3-wdt"; |
| reg = <0x4a314000 0x80>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "wd_timer2"; |
| }; |
| |
| mcpdm: mcpdm@40132000 { |
| compatible = "ti,omap4-mcpdm"; |
| reg = <0x40132000 0x7f>, /* MPU private access */ |
| <0x49032000 0x7f>; /* L3 Interconnect */ |
| reg-names = "mpu", "dma"; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mcpdm"; |
| dmas = <&sdma 65>, |
| <&sdma 66>; |
| dma-names = "up_link", "dn_link"; |
| status = "disabled"; |
| }; |
| |
| dmic: dmic@4012e000 { |
| compatible = "ti,omap4-dmic"; |
| reg = <0x4012e000 0x7f>, /* MPU private access */ |
| <0x4902e000 0x7f>; /* L3 Interconnect */ |
| reg-names = "mpu", "dma"; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "dmic"; |
| dmas = <&sdma 67>; |
| dma-names = "up_link"; |
| status = "disabled"; |
| }; |
| |
| mcbsp1: mcbsp@40122000 { |
| compatible = "ti,omap4-mcbsp"; |
| reg = <0x40122000 0xff>, /* MPU private access */ |
| <0x49022000 0xff>; /* L3 Interconnect */ |
| reg-names = "mpu", "dma"; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "common"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp1"; |
| dmas = <&sdma 33>, |
| <&sdma 34>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp2: mcbsp@40124000 { |
| compatible = "ti,omap4-mcbsp"; |
| reg = <0x40124000 0xff>, /* MPU private access */ |
| <0x49024000 0xff>; /* L3 Interconnect */ |
| reg-names = "mpu", "dma"; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "common"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp2"; |
| dmas = <&sdma 17>, |
| <&sdma 18>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp3: mcbsp@40126000 { |
| compatible = "ti,omap4-mcbsp"; |
| reg = <0x40126000 0xff>, /* MPU private access */ |
| <0x49026000 0xff>; /* L3 Interconnect */ |
| reg-names = "mpu", "dma"; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "common"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp3"; |
| dmas = <&sdma 19>, |
| <&sdma 20>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| mcbsp4: mcbsp@48096000 { |
| compatible = "ti,omap4-mcbsp"; |
| reg = <0x48096000 0xff>; /* L4 Interconnect */ |
| reg-names = "mpu"; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "common"; |
| ti,buffer-size = <128>; |
| ti,hwmods = "mcbsp4"; |
| dmas = <&sdma 31>, |
| <&sdma 32>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| keypad: keypad@4a31c000 { |
| compatible = "ti,omap4-keypad"; |
| reg = <0x4a31c000 0x80>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| reg-names = "mpu"; |
| ti,hwmods = "kbd"; |
| }; |
| |
| dmm@4e000000 { |
| compatible = "ti,omap4-dmm"; |
| reg = <0x4e000000 0x800>; |
| interrupts = <0 113 0x4>; |
| ti,hwmods = "dmm"; |
| }; |
| |
| emif1: emif@4c000000 { |
| compatible = "ti,emif-4d"; |
| reg = <0x4c000000 0x100>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "emif1"; |
| ti,no-idle-on-init; |
| phy-type = <1>; |
| hw-caps-read-idle-ctrl; |
| hw-caps-ll-interface; |
| hw-caps-temp-alert; |
| }; |
| |
| emif2: emif@4d000000 { |
| compatible = "ti,emif-4d"; |
| reg = <0x4d000000 0x100>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "emif2"; |
| ti,no-idle-on-init; |
| phy-type = <1>; |
| hw-caps-read-idle-ctrl; |
| hw-caps-ll-interface; |
| hw-caps-temp-alert; |
| }; |
| |
| ocp2scp@4a0ad000 { |
| compatible = "ti,omap-ocp2scp"; |
| reg = <0x4a0ad000 0x1f>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "ocp2scp_usb_phy"; |
| usb2_phy: usb2phy@4a0ad080 { |
| compatible = "ti,omap-usb2"; |
| reg = <0x4a0ad080 0x58>; |
| ctrl-module = <&omap_control_usb2phy>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| timer1: timer@4a318000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x4a318000 0x80>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer1"; |
| ti,timer-alwon; |
| }; |
| |
| timer2: timer@48032000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48032000 0x80>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer2"; |
| }; |
| |
| timer3: timer@48034000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x48034000 0x80>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer3"; |
| }; |
| |
| timer4: timer@48036000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x48036000 0x80>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer4"; |
| }; |
| |
| timer5: timer@40138000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x40138000 0x80>, |
| <0x49038000 0x80>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer5"; |
| ti,timer-dsp; |
| }; |
| |
| timer6: timer@4013a000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x4013a000 0x80>, |
| <0x4903a000 0x80>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer6"; |
| ti,timer-dsp; |
| }; |
| |
| timer7: timer@4013c000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x4013c000 0x80>, |
| <0x4903c000 0x80>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer7"; |
| ti,timer-dsp; |
| }; |
| |
| timer8: timer@4013e000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x4013e000 0x80>, |
| <0x4903e000 0x80>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer8"; |
| ti,timer-pwm; |
| ti,timer-dsp; |
| }; |
| |
| timer9: timer@4803e000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x4803e000 0x80>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer9"; |
| ti,timer-pwm; |
| }; |
| |
| timer10: timer@48086000 { |
| compatible = "ti,omap3430-timer"; |
| reg = <0x48086000 0x80>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer10"; |
| ti,timer-pwm; |
| }; |
| |
| timer11: timer@48088000 { |
| compatible = "ti,omap4430-timer"; |
| reg = <0x48088000 0x80>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer11"; |
| ti,timer-pwm; |
| }; |
| |
| usbhstll: usbhstll@4a062000 { |
| compatible = "ti,usbhs-tll"; |
| reg = <0x4a062000 0x1000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "usb_tll_hs"; |
| }; |
| |
| usbhshost: usbhshost@4a064000 { |
| compatible = "ti,usbhs-host"; |
| reg = <0x4a064000 0x800>; |
| ti,hwmods = "usb_host_hs"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| clocks = <&init_60m_fclk>, |
| <&xclk60mhsp1_ck>, |
| <&xclk60mhsp2_ck>; |
| clock-names = "refclk_60m_int", |
| "refclk_60m_ext_p1", |
| "refclk_60m_ext_p2"; |
| |
| usbhsohci: ohci@4a064800 { |
| compatible = "ti,ohci-omap3"; |
| reg = <0x4a064800 0x400>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| usbhsehci: ehci@4a064c00 { |
| compatible = "ti,ehci-omap"; |
| reg = <0x4a064c00 0x400>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| omap_control_usb2phy: control-phy@4a002300 { |
| compatible = "ti,control-phy-usb2"; |
| reg = <0x4a002300 0x4>; |
| reg-names = "power"; |
| }; |
| |
| omap_control_usbotg: control-phy@4a00233c { |
| compatible = "ti,control-phy-otghs"; |
| reg = <0x4a00233c 0x4>; |
| reg-names = "otghs_control"; |
| }; |
| |
| usb_otg_hs: usb_otg_hs@4a0ab000 { |
| compatible = "ti,omap4-musb"; |
| reg = <0x4a0ab000 0x7ff>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "mc", "dma"; |
| ti,hwmods = "usb_otg_hs"; |
| usb-phy = <&usb2_phy>; |
| phys = <&usb2_phy>; |
| phy-names = "usb2-phy"; |
| multipoint = <1>; |
| num-eps = <16>; |
| ram-bits = <12>; |
| ctrl-module = <&omap_control_usbotg>; |
| }; |
| |
| aes: aes@4b501000 { |
| compatible = "ti,omap4-aes"; |
| ti,hwmods = "aes"; |
| reg = <0x4b501000 0xa0>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 111>, <&sdma 110>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| des: des@480a5000 { |
| compatible = "ti,omap4-des"; |
| ti,hwmods = "des"; |
| reg = <0x480a5000 0xa0>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 117>, <&sdma 116>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| abb_mpu: regulator-abb-mpu { |
| compatible = "ti,abb-v2"; |
| regulator-name = "abb_mpu"; |
| #address-cells = <0>; |
| #size-cells = <0>; |
| ti,tranxdone-status-mask = <0x80>; |
| clocks = <&sys_clkin_ck>; |
| ti,settling-time = <50>; |
| ti,clock-cycles = <16>; |
| |
| status = "disabled"; |
| }; |
| |
| abb_iva: regulator-abb-iva { |
| compatible = "ti,abb-v2"; |
| regulator-name = "abb_iva"; |
| #address-cells = <0>; |
| #size-cells = <0>; |
| ti,tranxdone-status-mask = <0x80000000>; |
| clocks = <&sys_clkin_ck>; |
| ti,settling-time = <50>; |
| ti,clock-cycles = <16>; |
| |
| status = "disabled"; |
| }; |
| |
| dss: dss@58000000 { |
| compatible = "ti,omap4-dss"; |
| reg = <0x58000000 0x80>; |
| status = "disabled"; |
| ti,hwmods = "dss_core"; |
| clocks = <&dss_dss_clk>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| dispc@58001000 { |
| compatible = "ti,omap4-dispc"; |
| reg = <0x58001000 0x1000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "dss_dispc"; |
| clocks = <&dss_dss_clk>; |
| clock-names = "fck"; |
| }; |
| |
| rfbi: encoder@58002000 { |
| compatible = "ti,omap4-rfbi"; |
| reg = <0x58002000 0x1000>; |
| status = "disabled"; |
| ti,hwmods = "dss_rfbi"; |
| clocks = <&dss_dss_clk>, <&dss_fck>; |
| clock-names = "fck", "ick"; |
| }; |
| |
| venc: encoder@58003000 { |
| compatible = "ti,omap4-venc"; |
| reg = <0x58003000 0x1000>; |
| status = "disabled"; |
| ti,hwmods = "dss_venc"; |
| clocks = <&dss_tv_clk>; |
| clock-names = "fck"; |
| }; |
| |
| dsi1: encoder@58004000 { |
| compatible = "ti,omap4-dsi"; |
| reg = <0x58004000 0x200>, |
| <0x58004200 0x40>, |
| <0x58004300 0x20>; |
| reg-names = "proto", "phy", "pll"; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| ti,hwmods = "dss_dsi1"; |
| clocks = <&dss_dss_clk>, <&dss_sys_clk>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| |
| dsi2: encoder@58005000 { |
| compatible = "ti,omap4-dsi"; |
| reg = <0x58005000 0x200>, |
| <0x58005200 0x40>, |
| <0x58005300 0x20>; |
| reg-names = "proto", "phy", "pll"; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| ti,hwmods = "dss_dsi2"; |
| clocks = <&dss_dss_clk>, <&dss_sys_clk>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| |
| hdmi: encoder@58006000 { |
| compatible = "ti,omap4-hdmi"; |
| reg = <0x58006000 0x200>, |
| <0x58006200 0x100>, |
| <0x58006300 0x100>, |
| <0x58006400 0x1000>; |
| reg-names = "wp", "pll", "phy", "core"; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| ti,hwmods = "dss_hdmi"; |
| clocks = <&dss_48mhz_clk>, <&dss_sys_clk>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| }; |
| }; |
| }; |
| |
| /include/ "omap44xx-clocks.dtsi" |