Merge branch 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
* 'board' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: add minimal support for Nokia RM-696
ARM: OMAP: enable Bluetooth on the PandaBoard
ARM: OMAP: pandora: add support for backlight and poweroff
ARM: OMAP4: board-4430sdp: don't initialize value that is never used
ARM: OMAP3: cm-t3517: add EMAC support
ARM: OMAP: move generic EMAC init to separate file
ARM: OMAP3: RX-51: add explicit mux configuration of tsc2005 control gpios
ARM: OMAP: Add omap_reserve functionality
(includes sync-up to 3.3-rc6)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a48aecc..b5a91ca 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1578,6 +1578,7 @@
int
default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
default 350 if ARCH_U8500
+ default 264 if MACH_H4700
default 0
help
Maximum number of GPIOs in the system.
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index e0d236d..03646c4 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -81,25 +81,6 @@
prompt "Kernel low-level debugging port"
depends on DEBUG_LL
- config DEBUG_LL_UART_NONE
- bool "No low-level debugging UART"
- help
- Say Y here if your platform doesn't provide a UART option
- below. This relies on your platform choosing the right UART
- definition internally in order for low-level debugging to
- work.
-
- config DEBUG_ICEDCC
- bool "Kernel low-level debugging via EmbeddedICE DCC channel"
- help
- Say Y here if you want the debug print routines to direct
- their output to the EmbeddedICE macrocell's DCC channel using
- co-processor 14. This is known to work on the ARM9 style ICE
- channel and on the XScale with the PEEDI.
-
- Note that the system will appear to hang during boot if there
- is nothing connected to read from the DCC.
-
config AT91_DEBUG_LL_DBGU0
bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl"
depends on HAVE_AT91_DBGU0
@@ -108,20 +89,6 @@
bool "Kernel low-level debugging on 9263, 9g45 and cap9"
depends on HAVE_AT91_DBGU1
- config DEBUG_FOOTBRIDGE_COM1
- bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
- depends on FOOTBRIDGE
- help
- Say Y here if you want the debug print routines to direct
- their output to the 8250 at PCI COM1.
-
- config DEBUG_DC21285_PORT
- bool "Kernel low-level debugging messages via footbridge serial port"
- depends on FOOTBRIDGE
- help
- Say Y here if you want the debug print routines to direct
- their output to the serial port in the DC21285 (Footbridge).
-
config DEBUG_CLPS711X_UART1
bool "Kernel low-level debugging messages via UART1"
depends on ARCH_CLPS711X
@@ -136,6 +103,20 @@
Say Y here if you want the debug print routines to direct
their output to the second serial port on these devices.
+ config DEBUG_DC21285_PORT
+ bool "Kernel low-level debugging messages via footbridge serial port"
+ depends on FOOTBRIDGE
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port in the DC21285 (Footbridge).
+
+ config DEBUG_FOOTBRIDGE_COM1
+ bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+ depends on FOOTBRIDGE
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the 8250 at PCI COM1.
+
config DEBUG_HIGHBANK_UART
bool "Kernel low-level debugging messages via Highbank UART"
depends on ARCH_HIGHBANK
@@ -206,55 +187,6 @@
Say Y here if you want kernel low-level debugging support
on i.MX6Q.
- config DEBUG_S3C_UART0
- depends on PLAT_SAMSUNG
- bool "Use S3C UART 0 for low-level debug"
- help
- Say Y here if you want the debug print routines to direct
- their output to UART 0. The port must have been initialised
- by the boot-loader before use.
-
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
- config DEBUG_S3C_UART1
- depends on PLAT_SAMSUNG
- bool "Use S3C UART 1 for low-level debug"
- help
- Say Y here if you want the debug print routines to direct
- their output to UART 1. The port must have been initialised
- by the boot-loader before use.
-
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
- config DEBUG_S3C_UART2
- depends on PLAT_SAMSUNG
- bool "Use S3C UART 2 for low-level debug"
- help
- Say Y here if you want the debug print routines to direct
- their output to UART 2. The port must have been initialised
- by the boot-loader before use.
-
- The uncompressor code port configuration is now handled
- by CONFIG_S3C_LOWLEVEL_UART_PORT.
-
- config DEBUG_REALVIEW_STD_PORT
- bool "RealView Default UART"
- depends on ARCH_REALVIEW
- help
- Say Y here if you want the debug print routines to direct
- their output to the serial port on RealView EB, PB11MP, PBA8
- and PBX platforms.
-
- config DEBUG_REALVIEW_PB1176_PORT
- bool "RealView PB1176 UART"
- depends on MACH_REALVIEW_PB1176
- help
- Say Y here if you want the debug print routines to direct
- their output to the standard serial port on the RealView
- PB1176 platform.
-
config DEBUG_MSM_UART1
bool "Kernel low-level debugging messages via MSM UART1"
depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
@@ -292,6 +224,74 @@
Say Y here if you want the debug print routines to direct
their output to the serial port on MSM 8960 devices.
+ config DEBUG_REALVIEW_STD_PORT
+ bool "RealView Default UART"
+ depends on ARCH_REALVIEW
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the serial port on RealView EB, PB11MP, PBA8
+ and PBX platforms.
+
+ config DEBUG_REALVIEW_PB1176_PORT
+ bool "RealView PB1176 UART"
+ depends on MACH_REALVIEW_PB1176
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the standard serial port on the RealView
+ PB1176 platform.
+
+ config DEBUG_S3C_UART0
+ depends on PLAT_SAMSUNG
+ bool "Use S3C UART 0 for low-level debug"
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART 0. The port must have been initialised
+ by the boot-loader before use.
+
+ The uncompressor code port configuration is now handled
+ by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+ config DEBUG_S3C_UART1
+ depends on PLAT_SAMSUNG
+ bool "Use S3C UART 1 for low-level debug"
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART 1. The port must have been initialised
+ by the boot-loader before use.
+
+ The uncompressor code port configuration is now handled
+ by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+ config DEBUG_S3C_UART2
+ depends on PLAT_SAMSUNG
+ bool "Use S3C UART 2 for low-level debug"
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART 2. The port must have been initialised
+ by the boot-loader before use.
+
+ The uncompressor code port configuration is now handled
+ by CONFIG_S3C_LOWLEVEL_UART_PORT.
+
+ config DEBUG_LL_UART_NONE
+ bool "No low-level debugging UART"
+ help
+ Say Y here if your platform doesn't provide a UART option
+ below. This relies on your platform choosing the right UART
+ definition internally in order for low-level debugging to
+ work.
+
+ config DEBUG_ICEDCC
+ bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the EmbeddedICE macrocell's DCC channel using
+ co-processor 14. This is known to work on the ARM9 style ICE
+ channel and on the XScale with the PEEDI.
+
+ Note that the system will appear to hang during boot if there
+ is nothing connected to read from the DCC.
+
endchoice
config EARLY_PRINTK
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
new file mode 100644
index 0000000..8a5dff8
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -0,0 +1,25 @@
+/dts-v1/;
+
+/include/ "kirkwood.dtsi"
+
+/ {
+ model = "Globalscale Technologies Dreamplug";
+ compatible = "globalscale,dreamplug-003-ds2001", "globalscale,dreamplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ serial@f1012000 {
+ compatible = "ns16550a";
+ reg = <0xf1012000 0xff>;
+ reg-shift = <2>;
+ interrupts = <33>;
+ clock-frequency = <200000000>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
new file mode 100644
index 0000000..771c6bb
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -0,0 +1,6 @@
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "marvell,kirkwood";
+};
+
diff --git a/arch/arm/boot/dts/tegra-paz00.dts b/arch/arm/boot/dts/tegra-paz00.dts
index 825d295..61f3858 100644
--- a/arch/arm/boot/dts/tegra-paz00.dts
+++ b/arch/arm/boot/dts/tegra-paz00.dts
@@ -35,6 +35,11 @@
i2c@7000d000 {
clock-frequency = <400000>;
+
+ adt7461@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
};
serial@70006000 {
@@ -74,4 +79,25 @@
sdhci@c8000600 {
support-8bit;
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 79 1>; /* gpio PJ7, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ wifi {
+ label = "wifi-led";
+ gpios = <&gpio 24 0>;
+ linux,default-trigger = "rfkill0";
+ };
+ };
};
diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h
index e4c96cc..424aa45 100644
--- a/arch/arm/include/asm/system.h
+++ b/arch/arm/include/asm/system.h
@@ -110,6 +110,7 @@
void soft_restart(unsigned long);
extern void (*arm_pm_restart)(char str, const char *cmd);
+extern void (*arm_pm_idle)(void);
#define UDBG_UNDEFINED (1 << 0)
#define UDBG_SYSCALL (1 << 1)
diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c
index 971d65c..008e7ce 100644
--- a/arch/arm/kernel/process.c
+++ b/arch/arm/kernel/process.c
@@ -61,8 +61,6 @@
static volatile int hlt_counter;
-#include <mach/system.h>
-
void disable_hlt(void)
{
hlt_counter++;
@@ -181,13 +179,17 @@
EXPORT_SYMBOL_GPL(cpu_idle_wait);
/*
- * This is our default idle handler. We need to disable
- * interrupts here to ensure we don't miss a wakeup call.
+ * This is our default idle handler.
*/
+
+void (*arm_pm_idle)(void);
+
static void default_idle(void)
{
- if (!need_resched())
- arch_idle();
+ if (arm_pm_idle)
+ arm_pm_idle();
+ else
+ cpu_do_idle();
local_irq_enable();
}
@@ -215,6 +217,10 @@
cpu_die();
#endif
+ /*
+ * We need to disable interrupts here
+ * to ensure we don't miss a wakeup call.
+ */
local_irq_disable();
#ifdef CONFIG_PL310_ERRATA_769419
wmb();
@@ -222,19 +228,18 @@
if (hlt_counter) {
local_irq_enable();
cpu_relax();
- } else {
+ } else if (!need_resched()) {
stop_critical_timings();
if (cpuidle_idle_call())
pm_idle();
start_critical_timings();
/*
- * This will eventually be removed - pm_idle
- * functions should always return with IRQs
- * enabled.
+ * pm_idle functions must always
+ * return with IRQs enabled.
*/
WARN_ON(irqs_disabled());
+ } else
local_irq_enable();
- }
}
leds_event(led_idle_end);
rcu_idle_exit();
diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c
index a42edc2..8967d75 100644
--- a/arch/arm/mach-at91/at91cap9.c
+++ b/arch/arm/mach-at91/at91cap9.c
@@ -14,6 +14,7 @@
#include <linux/module.h>
+#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -313,6 +314,12 @@
}
};
+static void at91cap9_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
/* --------------------------------------------------------------------
* AT91CAP9 processor initialization
* -------------------------------------------------------------------- */
@@ -332,6 +339,7 @@
static void __init at91cap9_initialize(void)
{
+ arm_pm_idle = at91cap9_idle;
arm_pm_restart = at91sam9g45_restart;
at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 99c3174..dd6e2de 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -289,6 +289,15 @@
}
};
+static void at91rm9200_idle(void)
+{
+ /*
+ * Disable the processor clock. The processor will be automatically
+ * re-enabled by an interrupt or by a reset.
+ */
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+}
+
static void at91rm9200_restart(char mode, const char *cmd)
{
/*
@@ -314,6 +323,7 @@
static void __init at91rm9200_initialize(void)
{
+ arm_pm_idle = at91rm9200_idle;
arm_pm_restart = at91rm9200_restart;
at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
| (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index d4036ba..9ac8c6f 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -12,6 +12,7 @@
#include <linux/module.h>
+#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -328,8 +329,15 @@
at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
}
+static void at91sam9260_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
static void __init at91sam9260_initialize(void)
{
+ arm_pm_idle = at91sam9260_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
| (1 << AT91SAM9260_ID_IRQ2);
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 023c2ff..ab76868 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -12,6 +12,7 @@
#include <linux/module.h>
+#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -286,8 +287,15 @@
at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
}
+static void at91sam9261_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
static void __init at91sam9261_initialize(void)
{
+ arm_pm_idle = at91sam9261_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
| (1 << AT91SAM9261_ID_IRQ2);
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 75e876c..247ab63 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -12,6 +12,7 @@
#include <linux/module.h>
+#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -307,8 +308,15 @@
at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
}
+static void at91sam9263_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
static void __init at91sam9263_initialize(void)
{
+ arm_pm_idle = at91sam9263_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 1cb6a96..5b12192 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -317,6 +317,12 @@
}
};
+static void at91sam9g45_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
/* --------------------------------------------------------------------
* AT91SAM9G45 processor initialization
* -------------------------------------------------------------------- */
@@ -337,6 +343,7 @@
static void __init at91sam9g45_initialize(void)
{
+ arm_pm_idle = at91sam9g45_idle;
arm_pm_restart = at91sam9g45_restart;
at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index d2c91a8..fd60e22 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -11,6 +11,7 @@
#include <linux/module.h>
+#include <asm/proc-fns.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -291,8 +292,15 @@
at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
}
+static void at91sam9rl_idle(void)
+{
+ at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+ cpu_do_idle();
+}
+
static void __init at91sam9rl_initialize(void)
{
+ arm_pm_idle = at91sam9rl_idle;
arm_pm_restart = at91sam9_alt_restart;
at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
diff --git a/arch/arm/mach-at91/at91x40.c b/arch/arm/mach-at91/at91x40.c
index 56ba3bd..0154b7f 100644
--- a/arch/arm/mach-at91/at91x40.c
+++ b/arch/arm/mach-at91/at91x40.c
@@ -13,6 +13,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/irq.h>
+#include <asm/proc-fns.h>
#include <asm/mach/arch.h>
#include <mach/at91x40.h>
#include <mach/at91_st.h>
@@ -37,8 +38,19 @@
return AT91X40_MASTER_CLOCK;
}
+static void at91x40_idle(void)
+{
+ /*
+ * Disable the processor clock. The processor will be automatically
+ * re-enabled by an interrupt or by a reset.
+ */
+ at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
+ cpu_do_idle();
+}
+
void __init at91x40_initialize(unsigned long main_clock)
{
+ arm_pm_idle = at91x40_idle;
at91_extern_irq = (1 << AT91X40_ID_IRQ0) | (1 << AT91X40_ID_IRQ1)
| (1 << AT91X40_ID_IRQ2);
}
diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h
deleted file mode 100644
index cbd64f3..0000000
--- a/arch/arm/mach-at91/include/mach/system.h
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/system.h
- *
- * Copyright (C) 2003 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/hardware.h>
-#include <mach/at91_st.h>
-#include <mach/at91_dbgu.h>
-#include <mach/at91_pmc.h>
-
-static inline void arch_idle(void)
-{
- /*
- * Disable the processor clock. The processor will be automatically
- * re-enabled by an interrupt or by a reset.
- */
-#ifdef AT91_PS
- at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
-#else
- at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
-#endif
-#ifndef CONFIG_CPU_ARM920T
- /*
- * Set the processor (CP15) into 'Wait for Interrupt' mode.
- * Post-RM9200 processors need this in conjunction with the above
- * to save power when idle.
- */
- cpu_do_idle();
-#endif
-}
-
-#endif
diff --git a/arch/arm/mach-bcmring/core.c b/arch/arm/mach-bcmring/core.c
index 6b67b7e..22e4e0a 100644
--- a/arch/arm/mach-bcmring/core.c
+++ b/arch/arm/mach-bcmring/core.c
@@ -52,27 +52,8 @@
#include <mach/csp/chipcHw_inline.h>
#include <mach/csp/tmrHw_reg.h>
-#define AMBA_DEVICE(name, initname, base, plat, size) \
-static struct amba_device name##_device = { \
- .dev = { \
- .coherent_dma_mask = ~0, \
- .init_name = initname, \
- .platform_data = plat \
- }, \
- .res = { \
- .start = MM_ADDR_IO_##base, \
- .end = MM_ADDR_IO_##base + (size) - 1, \
- .flags = IORESOURCE_MEM \
- }, \
- .dma_mask = ~0, \
- .irq = { \
- IRQ_##base \
- } \
-}
-
-
-AMBA_DEVICE(uartA, "uarta", UARTA, NULL, SZ_4K);
-AMBA_DEVICE(uartB, "uartb", UARTB, NULL, SZ_4K);
+static AMBA_APB_DEVICE(uartA, "uarta", MM_ADDR_IO_UARTA, { IRQ_UARTA }, NULL);
+static AMBA_APB_DEVICE(uartB, "uartb", MM_ADDR_IO_UARTB, { IRQ_UARTB }, NULL);
static struct clk pll1_clk = {
.name = "PLL1",
diff --git a/arch/arm/mach-bcmring/include/mach/system.h b/arch/arm/mach-bcmring/include/mach/system.h
deleted file mode 100644
index cb78250..0000000
--- a/arch/arm/mach-bcmring/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- *
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-clps711x/common.c b/arch/arm/mach-clps711x/common.c
index ab1711b..8736c1a 100644
--- a/arch/arm/mach-clps711x/common.c
+++ b/arch/arm/mach-clps711x/common.c
@@ -225,3 +225,19 @@
{
soft_restart(0);
}
+
+static void clps711x_idle(void)
+{
+ clps_writel(1, HALT);
+ __asm__ __volatile__(
+ "mov r0, r0\n\
+ mov r0, r0");
+}
+
+static int __init clps711x_idle_init(void)
+{
+ arm_pm_idle = clps711x_idle;
+ return 0;
+}
+
+arch_initcall(clps711x_idle_init);
diff --git a/arch/arm/mach-clps711x/include/mach/system.h b/arch/arm/mach-clps711x/include/mach/system.h
deleted file mode 100644
index 23d6ef8..0000000
--- a/arch/arm/mach-clps711x/include/mach/system.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * arch/arm/mach-clps711x/include/mach/system.h
- *
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/hardware/clps7111.h>
-
-static inline void arch_idle(void)
-{
- clps_writel(1, HALT);
- __asm__ __volatile__(
- "mov r0, r0\n\
- mov r0, r0");
-}
-
-#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h
deleted file mode 100644
index 9e56b7d..0000000
--- a/arch/arm/mach-cns3xxx/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * Copyright 2000 Deep Blue Solutions Ltd
- * Copyright 2003 ARM Limited
- * Copyright 2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <asm/proc-fns.h>
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-davinci/include/mach/system.h b/arch/arm/mach-davinci/include/mach/system.h
deleted file mode 100644
index fcb7a01..0000000
--- a/arch/arm/mach-davinci/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * DaVinci system defines
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/common.h>
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-dove/include/mach/system.h b/arch/arm/mach-dove/include/mach/system.h
deleted file mode 100644
index 3027954..0000000
--- a/arch/arm/mach-dove/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-dove/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-ebsa110/core.c b/arch/arm/mach-ebsa110/core.c
index 294aad0..804c912 100644
--- a/arch/arm/mach-ebsa110/core.c
+++ b/arch/arm/mach-ebsa110/core.c
@@ -271,8 +271,33 @@
&am79c961_device,
};
+/*
+ * EBSA110 idling methodology:
+ *
+ * We can not execute the "wait for interrupt" instruction since that
+ * will stop our MCLK signal (which provides the clock for the glue
+ * logic, and therefore the timer interrupt).
+ *
+ * Instead, we spin, polling the IRQ_STAT register for the occurrence
+ * of any interrupt with core clock down to the memory clock.
+ */
+static void ebsa110_idle(void)
+{
+ const char *irq_stat = (char *)0xff000000;
+
+ /* disable clock switching */
+ asm volatile ("mcr p15, 0, ip, c15, c2, 2" : : : "cc");
+
+ /* wait for an interrupt to occur */
+ while (!*irq_stat);
+
+ /* enable clock switching */
+ asm volatile ("mcr p15, 0, ip, c15, c1, 2" : : : "cc");
+}
+
static int __init ebsa110_init(void)
{
+ arm_pm_idle = ebsa110_idle;
return platform_add_devices(ebsa110_devices, ARRAY_SIZE(ebsa110_devices));
}
diff --git a/arch/arm/mach-ebsa110/include/mach/system.h b/arch/arm/mach-ebsa110/include/mach/system.h
deleted file mode 100644
index 2e4af65..0000000
--- a/arch/arm/mach-ebsa110/include/mach/system.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- * arch/arm/mach-ebsa110/include/mach/system.h
- *
- * Copyright (C) 1996-2000 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-/*
- * EBSA110 idling methodology:
- *
- * We can not execute the "wait for interrupt" instruction since that
- * will stop our MCLK signal (which provides the clock for the glue
- * logic, and therefore the timer interrupt).
- *
- * Instead, we spin, polling the IRQ_STAT register for the occurrence
- * of any interrupt with core clock down to the memory clock.
- */
-static inline void arch_idle(void)
-{
- const char *irq_stat = (char *)0xff000000;
-
- /* disable clock switching */
- asm volatile ("mcr p15, 0, ip, c15, c2, 2" : : : "cc");
-
- /* wait for an interrupt to occur */
- while (!*irq_stat);
-
- /* enable clock switching */
- asm volatile ("mcr p15, 0, ip, c15, c1, 2" : : : "cc");
-}
-
-#endif
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 24203f9..903edb0 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -279,48 +279,14 @@
.set_mctrl = ep93xx_uart_set_mctrl,
};
-static struct amba_device uart1_device = {
- .dev = {
- .init_name = "apb:uart1",
- .platform_data = &ep93xx_uart_data,
- },
- .res = {
- .start = EP93XX_UART1_PHYS_BASE,
- .end = EP93XX_UART1_PHYS_BASE + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_EP93XX_UART1, NO_IRQ },
- .periphid = 0x00041010,
-};
+static AMBA_APB_DEVICE(uart1, "apb:uart1", 0x00041010, EP93XX_UART1_PHYS_BASE,
+ { IRQ_EP93XX_UART1 }, &ep93xx_uart_data);
-static struct amba_device uart2_device = {
- .dev = {
- .init_name = "apb:uart2",
- .platform_data = &ep93xx_uart_data,
- },
- .res = {
- .start = EP93XX_UART2_PHYS_BASE,
- .end = EP93XX_UART2_PHYS_BASE + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_EP93XX_UART2, NO_IRQ },
- .periphid = 0x00041010,
-};
+static AMBA_APB_DEVICE(uart2, "apb:uart2", 0x00041010, EP93XX_UART2_PHYS_BASE,
+ { IRQ_EP93XX_UART2 }, &ep93xx_uart_data);
-static struct amba_device uart3_device = {
- .dev = {
- .init_name = "apb:uart3",
- .platform_data = &ep93xx_uart_data,
- },
- .res = {
- .start = EP93XX_UART3_PHYS_BASE,
- .end = EP93XX_UART3_PHYS_BASE + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_EP93XX_UART3, NO_IRQ },
- .periphid = 0x00041010,
-};
-
+static AMBA_APB_DEVICE(uart3, "apb:uart3", 0x00041010, EP93XX_UART3_PHYS_BASE,
+ { IRQ_EP93XX_UART3 }, &ep93xx_uart_data);
static struct resource ep93xx_rtc_resource[] = {
{
diff --git a/arch/arm/mach-ep93xx/include/mach/system.h b/arch/arm/mach-ep93xx/include/mach/system.h
deleted file mode 100644
index b5bec7c..0000000
--- a/arch/arm/mach-ep93xx/include/mach/system.h
+++ /dev/null
@@ -1,7 +0,0 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/system.h
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index c59e188..031c1e5 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -201,14 +201,6 @@
},
};
-static void exynos_idle(void)
-{
- if (!need_resched())
- cpu_do_idle();
-
- local_irq_enable();
-}
-
void exynos4_restart(char mode, const char *cmd)
{
__raw_writel(0x1, S5P_SWRESET);
@@ -467,10 +459,6 @@
int __init exynos_init(void)
{
printk(KERN_INFO "EXYNOS: Initializing architecture\n");
-
- /* set idle function */
- pm_idle = exynos_idle;
-
return device_register(&exynos4_dev);
}
diff --git a/arch/arm/mach-exynos/dma.c b/arch/arm/mach-exynos/dma.c
index b10fcd2..91370de 100644
--- a/arch/arm/mach-exynos/dma.c
+++ b/arch/arm/mach-exynos/dma.c
@@ -74,21 +74,8 @@
.peri_id = pdma0_peri,
};
-struct amba_device exynos4_device_pdma0 = {
- .dev = {
- .init_name = "dma-pl330.0",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &exynos4_pdma0_pdata,
- },
- .res = {
- .start = EXYNOS4_PA_PDMA0,
- .end = EXYNOS4_PA_PDMA0 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA0, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(exynos4_pdma0, "dma-pl330.0", 0x00041330, EXYNOS4_PA_PDMA0,
+ {IRQ_PDMA0}, &exynos4_pdma0_pdata);
u8 pdma1_peri[] = {
DMACH_PCM0_RX,
@@ -123,21 +110,8 @@
.peri_id = pdma1_peri,
};
-struct amba_device exynos4_device_pdma1 = {
- .dev = {
- .init_name = "dma-pl330.1",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &exynos4_pdma1_pdata,
- },
- .res = {
- .start = EXYNOS4_PA_PDMA1,
- .end = EXYNOS4_PA_PDMA1 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA1, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(exynos4_pdma1, "dma-pl330.1", 0x00041330, EXYNOS4_PA_PDMA1,
+ {IRQ_PDMA1}, &exynos4_pdma1_pdata);
static int __init exynos4_dma_init(void)
{
@@ -146,11 +120,11 @@
dma_cap_set(DMA_SLAVE, exynos4_pdma0_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, exynos4_pdma0_pdata.cap_mask);
- amba_device_register(&exynos4_device_pdma0, &iomem_resource);
+ amba_device_register(&exynos4_pdma0_device, &iomem_resource);
dma_cap_set(DMA_SLAVE, exynos4_pdma1_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, exynos4_pdma1_pdata.cap_mask);
- amba_device_register(&exynos4_device_pdma1, &iomem_resource);
+ amba_device_register(&exynos4_pdma1_device, &iomem_resource);
return 0;
}
diff --git a/arch/arm/mach-exynos/include/mach/system.h b/arch/arm/mach-exynos/include/mach/system.h
deleted file mode 100644
index 0063a6d..0000000
--- a/arch/arm/mach-exynos/include/mach/system.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* linux/arch/arm/mach-exynos4/include/mach/system.h
- *
- * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * EXYNOS4 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
- /* nothing here yet */
-}
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-footbridge/include/mach/system.h b/arch/arm/mach-footbridge/include/mach/system.h
deleted file mode 100644
index a174a58..0000000
--- a/arch/arm/mach-footbridge/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-footbridge/include/mach/system.h
- *
- * Copyright (C) 1996-1999 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-gemini/Makefile b/arch/arm/mach-gemini/Makefile
index c5b24b9..7355c0b 100644
--- a/arch/arm/mach-gemini/Makefile
+++ b/arch/arm/mach-gemini/Makefile
@@ -4,7 +4,7 @@
# Object file lists.
-obj-y := irq.o mm.o time.o devices.o gpio.o
+obj-y := irq.o mm.o time.o devices.o gpio.o idle.o
# Board-specific support
obj-$(CONFIG_MACH_NAS4220B) += board-nas4220b.o
diff --git a/arch/arm/mach-gemini/idle.c b/arch/arm/mach-gemini/idle.c
new file mode 100644
index 0000000..92bbd6b
--- /dev/null
+++ b/arch/arm/mach-gemini/idle.c
@@ -0,0 +1,29 @@
+/*
+ * arch/arm/mach-gemini/idle.c
+ */
+
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/proc-fns.h>
+
+static void gemini_idle(void)
+{
+ /*
+ * Because of broken hardware we have to enable interrupts or the CPU
+ * will never wakeup... Acctualy it is not very good to enable
+ * interrupts first since scheduler can miss a tick, but there is
+ * no other way around this. Platforms that needs it for power saving
+ * should call enable_hlt() in init code, since by default it is
+ * disabled.
+ */
+ local_irq_enable();
+ cpu_do_idle();
+}
+
+static int __init gemini_idle_init(void)
+{
+ arm_pm_idle = gemini_idle;
+ return 0;
+}
+
+arch_initcall(gemini_idle_init);
diff --git a/arch/arm/mach-gemini/include/mach/system.h b/arch/arm/mach-gemini/include/mach/system.h
index 4d9c1f8..a33b5a1 100644
--- a/arch/arm/mach-gemini/include/mach/system.h
+++ b/arch/arm/mach-gemini/include/mach/system.h
@@ -14,20 +14,6 @@
#include <mach/hardware.h>
#include <mach/global_reg.h>
-static inline void arch_idle(void)
-{
- /*
- * Because of broken hardware we have to enable interrupts or the CPU
- * will never wakeup... Acctualy it is not very good to enable
- * interrupts here since scheduler can miss a tick, but there is
- * no other way around this. Platforms that needs it for power saving
- * should call enable_hlt() in init code, since by default it is
- * disabled.
- */
- local_irq_enable();
- cpu_do_idle();
-}
-
static inline void arch_reset(char mode, const char *cmd)
{
__raw_writel(RESET_GLOBAL | RESET_CPU1,
diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c
index 9485a8f..ca70e5f 100644
--- a/arch/arm/mach-gemini/irq.c
+++ b/arch/arm/mach-gemini/irq.c
@@ -73,8 +73,8 @@
unsigned int i, mode = 0, level = 0;
/*
- * Disable arch_idle() by default since it is buggy
- * For more info see arch/arm/mach-gemini/include/mach/system.h
+ * Disable the idle handler by default since it is buggy
+ * For more info see arch/arm/mach-gemini/idle.c
*/
disable_hlt();
diff --git a/arch/arm/mach-h720x/common.c b/arch/arm/mach-h720x/common.c
index f8a2f6b..e756d1a 100644
--- a/arch/arm/mach-h720x/common.c
+++ b/arch/arm/mach-h720x/common.c
@@ -247,3 +247,21 @@
{
CPU_REG (PMU_BASE, PMU_STAT) |= PMU_WARMRESET;
}
+
+static void h720x__idle(void)
+{
+ CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
+ nop();
+ nop();
+ CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
+ nop();
+ nop();
+}
+
+static int __init h720x_idle_init(void)
+{
+ arm_pm_idle = h720x__idle;
+ return 0;
+}
+
+arch_initcall(h720x_idle_init);
diff --git a/arch/arm/mach-h720x/include/mach/system.h b/arch/arm/mach-h720x/include/mach/system.h
deleted file mode 100644
index 16ac46e..0000000
--- a/arch/arm/mach-h720x/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-h720x/include/mach/system.h
- *
- * Copyright (C) 2001-2002 Jungjun Kim, Hynix Semiconductor Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- * arch/arm/mach-h720x/include/mach/system.h
- *
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-#include <mach/hardware.h>
-
-static void arch_idle(void)
-{
- CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_IDLE;
- nop();
- nop();
- CPU_REG (PMU_BASE, PMU_MODE) = PMU_MODE_RUN;
- nop();
- nop();
-}
-
-#endif
diff --git a/arch/arm/mach-highbank/include/mach/system.h b/arch/arm/mach-highbank/include/mach/system.h
deleted file mode 100644
index b1d8b5f..0000000
--- a/arch/arm/mach-highbank/include/mach/system.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Copyright 2010-2011 Calxeda, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program. If not, see <http://www.gnu.org/licenses/>.
- */
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 4defb97b..96b1f62 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -320,8 +320,10 @@
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_SSI
select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_MMC
+ select IMX_HAVE_PLATFORM_MX2_CAMERA
select IMX_HAVE_PLATFORM_MXC_EHCI
+ select IMX_HAVE_PLATFORM_MXC_MMC
+ select LEDS_GPIO_REGISTER
help
Include support for Visstrim_m10 platform and its different variants.
This includes specific configurations for the board and its
@@ -492,6 +494,7 @@
bool "Support mx31moboard platforms (EPFL Mobots group)"
select SOC_IMX31
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
+ select IMX_HAVE_PLATFORM_IMX2_WDT
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_IPU_CORE
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
index c2766ae..0a1643c 100644
--- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
+++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
@@ -30,6 +30,10 @@
#include <linux/input.h>
#include <linux/gpio.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/leds.h>
+#include <linux/memblock.h>
+#include <media/soc_camera.h>
#include <sound/tlv320aic32x4.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -39,6 +43,8 @@
#include "devices-imx27.h"
+#define TVP5150_RSTN (GPIO_PORTC + 18)
+#define TVP5150_PWDN (GPIO_PORTC + 19)
#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
#define SDHC1_IRQ IRQ_GPIOB(25)
@@ -100,8 +106,99 @@
PE1_PF_USBOTG_STP,
PB23_PF_USB_PWR,
PB24_PF_USB_OC,
+ /* CSI */
+ PB10_PF_CSI_D0,
+ PB11_PF_CSI_D1,
+ PB12_PF_CSI_D2,
+ PB13_PF_CSI_D3,
+ PB14_PF_CSI_D4,
+ PB15_PF_CSI_MCLK,
+ PB16_PF_CSI_PIXCLK,
+ PB17_PF_CSI_D5,
+ PB18_PF_CSI_D6,
+ PB19_PF_CSI_D7,
+ PB20_PF_CSI_VSYNC,
+ PB21_PF_CSI_HSYNC,
};
+/* Camera */
+static int visstrim_camera_power(struct device *dev, int on)
+{
+ gpio_set_value(TVP5150_PWDN, on);
+
+ return 0;
+};
+
+static int visstrim_camera_reset(struct device *dev)
+{
+ gpio_set_value(TVP5150_RSTN, 0);
+ ndelay(500);
+ gpio_set_value(TVP5150_RSTN, 1);
+
+ return 0;
+};
+
+static struct i2c_board_info visstrim_i2c_camera = {
+ I2C_BOARD_INFO("tvp5150", 0x5d),
+};
+
+static struct soc_camera_link iclink_tvp5150 = {
+ .bus_id = 0,
+ .board_info = &visstrim_i2c_camera,
+ .i2c_adapter_id = 0,
+ .power = visstrim_camera_power,
+ .reset = visstrim_camera_reset,
+};
+
+static struct mx2_camera_platform_data visstrim_camera = {
+ .flags = MX2_CAMERA_CCIR | MX2_CAMERA_CCIR_INTERLACE |
+ MX2_CAMERA_SWAP16 | MX2_CAMERA_PCLK_SAMPLE_RISING,
+ .clk = 100000,
+};
+
+static phys_addr_t mx2_camera_base __initdata;
+#define MX2_CAMERA_BUF_SIZE SZ_8M
+
+static void __init visstrim_camera_init(void)
+{
+ struct platform_device *pdev;
+ int dma;
+
+ /* Initialize tvp5150 gpios */
+ mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT);
+ mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT);
+ gpio_set_value(TVP5150_RSTN, 1);
+ gpio_set_value(TVP5150_PWDN, 0);
+ ndelay(1);
+
+ gpio_set_value(TVP5150_PWDN, 1);
+ ndelay(1);
+ gpio_set_value(TVP5150_RSTN, 0);
+ ndelay(500);
+ gpio_set_value(TVP5150_RSTN, 1);
+ ndelay(200000);
+
+ pdev = imx27_add_mx2_camera(&visstrim_camera);
+ if (IS_ERR(pdev))
+ return;
+
+ dma = dma_declare_coherent_memory(&pdev->dev,
+ mx2_camera_base, mx2_camera_base,
+ MX2_CAMERA_BUF_SIZE,
+ DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE);
+ if (!(dma & DMA_MEMORY_MAP))
+ return;
+}
+
+static void __init visstrim_reserve(void)
+{
+ /* reserve 4 MiB for mx2-camera */
+ mx2_camera_base = memblock_alloc(MX2_CAMERA_BUF_SIZE,
+ MX2_CAMERA_BUF_SIZE);
+ memblock_free(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
+ memblock_remove(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
+}
+
/* GPIOs used as events for applications */
static struct gpio_keys_button visstrim_gpio_keys[] = {
{
@@ -136,6 +233,35 @@
.nbuttons = ARRAY_SIZE(visstrim_gpio_keys),
};
+/* led */
+static const struct gpio_led visstrim_m10_leds[] __initconst = {
+ {
+ .name = "visstrim:ld0",
+ .default_trigger = "nand-disk",
+ .gpio = (GPIO_PORTC + 29),
+ },
+ {
+ .name = "visstrim:ld1",
+ .default_trigger = "nand-disk",
+ .gpio = (GPIO_PORTC + 24),
+ },
+ {
+ .name = "visstrim:ld2",
+ .default_trigger = "nand-disk",
+ .gpio = (GPIO_PORTC + 28),
+ },
+ {
+ .name = "visstrim:ld3",
+ .default_trigger = "nand-disk",
+ .gpio = (GPIO_PORTC + 25),
+ },
+};
+
+static const struct gpio_led_platform_data visstrim_m10_led_data __initconst = {
+ .leds = visstrim_m10_leds,
+ .num_leds = ARRAY_SIZE(visstrim_m10_leds),
+};
+
/* Visstrim_SM10 has a microSD slot connected to sdhc1 */
static int visstrim_m10_sdhc1_init(struct device *dev,
irq_handler_t detect_irq, void *data)
@@ -216,6 +342,9 @@
{
I2C_BOARD_INFO("tlv320aic32x4", 0x18),
.platform_data = &visstrim_m10_aic32x4_pdata,
+ },
+ {
+ I2C_BOARD_INFO("m41t00", 0x68),
}
};
@@ -254,15 +383,20 @@
imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
imx27_add_imx_uart0(&uart_pdata);
- i2c_register_board_info(0, visstrim_m10_i2c_devices,
- ARRAY_SIZE(visstrim_m10_i2c_devices));
imx27_add_imx_i2c(0, &visstrim_m10_i2c_data);
imx27_add_imx_i2c(1, &visstrim_m10_i2c_data);
+ i2c_register_board_info(0, visstrim_m10_i2c_devices,
+ ARRAY_SIZE(visstrim_m10_i2c_devices));
+
imx27_add_mxc_mmc(0, &visstrim_m10_sdhc_pdata);
imx27_add_mxc_ehci_otg(&visstrim_m10_usbotg_pdata);
imx27_add_fec(NULL);
imx_add_gpio_keys(&visstrim_gpio_keys_platform_data);
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+ platform_device_register_resndata(NULL, "soc-camera-pdrv", 0, NULL, 0,
+ &iclink_tvp5150, sizeof(iclink_tvp5150));
+ gpio_led_register_device(0, &visstrim_m10_led_data);
+ visstrim_camera_init();
}
static void __init visstrim_m10_timer_init(void)
@@ -276,6 +410,7 @@
MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
.atag_offset = 0x100,
+ .reserve = visstrim_reserve,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
.init_irq = mx27_init_irq,
diff --git a/arch/arm/mach-imx/mach-mx31moboard.c b/arch/arm/mach-imx/mach-mx31moboard.c
index f225262..c0511fb 100644
--- a/arch/arm/mach-imx/mach-mx31moboard.c
+++ b/arch/arm/mach-imx/mach-mx31moboard.c
@@ -530,6 +530,8 @@
platform_add_devices(devices, ARRAY_SIZE(devices));
gpio_led_register_device(-1, &mx31moboard_led_pdata);
+ imx31_add_imx2_wdt(NULL);
+
imx31_add_imx_uart0(&uart0_pdata);
imx31_add_imx_uart4(&uart4_pdata);
@@ -590,7 +592,7 @@
}
MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
- /* Maintainer: Valentin Longchamp, EPFL Mobots group */
+ /* Maintainer: Philippe Retornaz, EPFL Mobots group */
.atag_offset = 0x100,
.reserve = mx31moboard_reserve,
.map_io = mx31_map_io,
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index 31807d2..8404ee7 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -34,31 +34,29 @@
{
unsigned long reg = 0;
- if (!need_resched())
- __asm__ __volatile__(
- /* disable I and D cache */
- "mrc p15, 0, %0, c1, c0, 0\n"
- "bic %0, %0, #0x00001000\n"
- "bic %0, %0, #0x00000004\n"
- "mcr p15, 0, %0, c1, c0, 0\n"
- /* invalidate I cache */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c5, 0\n"
- /* clear and invalidate D cache */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c14, 0\n"
- /* WFI */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c0, 4\n"
- "nop\n" "nop\n" "nop\n" "nop\n"
- "nop\n" "nop\n" "nop\n"
- /* enable I and D cache */
- "mrc p15, 0, %0, c1, c0, 0\n"
- "orr %0, %0, #0x00001000\n"
- "orr %0, %0, #0x00000004\n"
- "mcr p15, 0, %0, c1, c0, 0\n"
- : "=r" (reg));
- local_irq_enable();
+ __asm__ __volatile__(
+ /* disable I and D cache */
+ "mrc p15, 0, %0, c1, c0, 0\n"
+ "bic %0, %0, #0x00001000\n"
+ "bic %0, %0, #0x00000004\n"
+ "mcr p15, 0, %0, c1, c0, 0\n"
+ /* invalidate I cache */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c5, 0\n"
+ /* clear and invalidate D cache */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c14, 0\n"
+ /* WFI */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c0, 4\n"
+ "nop\n" "nop\n" "nop\n" "nop\n"
+ "nop\n" "nop\n" "nop\n"
+ /* enable I and D cache */
+ "mrc p15, 0, %0, c1, c0, 0\n"
+ "orr %0, %0, #0x00001000\n"
+ "orr %0, %0, #0x00000004\n"
+ "mcr p15, 0, %0, c1, c0, 0\n"
+ : "=r" (reg));
}
static void __iomem *imx3_ioremap(unsigned long phys_addr, size_t size,
@@ -134,8 +132,8 @@
{
mxc_set_cpu_type(MXC_CPU_MX31);
mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
- pm_idle = imx3_idle;
imx_ioremap = imx3_ioremap;
+ arm_pm_idle = imx3_idle;
}
void __init mx31_init_irq(void)
@@ -197,7 +195,7 @@
mxc_set_cpu_type(MXC_CPU_MX35);
mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
- pm_idle = imx3_idle;
+ arm_pm_idle = imx3_idle;
imx_ioremap = imx3_ioremap;
}
diff --git a/arch/arm/mach-imx/mm-imx5.c b/arch/arm/mach-imx/mm-imx5.c
index bc17dfe..49549a7 100644
--- a/arch/arm/mach-imx/mm-imx5.c
+++ b/arch/arm/mach-imx/mm-imx5.c
@@ -26,23 +26,17 @@
static void imx5_idle(void)
{
- if (!need_resched()) {
- /* gpc clock is needed for SRPG */
- if (gpc_dvfs_clk == NULL) {
- gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
- if (IS_ERR(gpc_dvfs_clk))
- goto err0;
- }
- clk_enable(gpc_dvfs_clk);
- mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
- if (tzic_enable_wake())
- goto err1;
- cpu_do_idle();
-err1:
- clk_disable(gpc_dvfs_clk);
+ /* gpc clock is needed for SRPG */
+ if (gpc_dvfs_clk == NULL) {
+ gpc_dvfs_clk = clk_get(NULL, "gpc_dvfs");
+ if (IS_ERR(gpc_dvfs_clk))
+ return;
}
-err0:
- local_irq_enable();
+ clk_enable(gpc_dvfs_clk);
+ mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+ if (tzic_enable_wake() != 0)
+ cpu_do_idle();
+ clk_disable(gpc_dvfs_clk);
}
/*
@@ -108,7 +102,7 @@
mxc_set_cpu_type(MXC_CPU_MX51);
mxc_iomux_v3_init(MX51_IO_ADDRESS(MX51_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX51_IO_ADDRESS(MX51_WDOG1_BASE_ADDR));
- pm_idle = imx5_idle;
+ arm_pm_idle = imx5_idle;
}
void __init imx53_init_early(void)
diff --git a/arch/arm/mach-imx/pm-imx27.c b/arch/arm/mach-imx/pm-imx27.c
index e455d2f..6fcffa7 100644
--- a/arch/arm/mach-imx/pm-imx27.c
+++ b/arch/arm/mach-imx/pm-imx27.c
@@ -10,7 +10,6 @@
#include <linux/kernel.h>
#include <linux/suspend.h>
#include <linux/io.h>
-#include <mach/system.h>
#include <mach/hardware.h>
static int mx27_suspend_enter(suspend_state_t state)
@@ -23,7 +22,7 @@
cscr &= 0xFFFFFFFC;
__raw_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
/* Executes WFI */
- arch_idle();
+ cpu_do_idle();
break;
default:
diff --git a/arch/arm/mach-integrator/core.c b/arch/arm/mach-integrator/core.c
index 019f0ab..15b87f2 100644
--- a/arch/arm/mach-integrator/core.c
+++ b/arch/arm/mach-integrator/core.c
@@ -35,67 +35,23 @@
static struct amba_pl010_data integrator_uart_data;
-static struct amba_device rtc_device = {
- .dev = {
- .init_name = "mb:15",
- },
- .res = {
- .start = INTEGRATOR_RTC_BASE,
- .end = INTEGRATOR_RTC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_RTCINT, NO_IRQ },
-};
+#define INTEGRATOR_RTC_IRQ { IRQ_RTCINT }
+#define INTEGRATOR_UART0_IRQ { IRQ_UARTINT0 }
+#define INTEGRATOR_UART1_IRQ { IRQ_UARTINT1 }
+#define KMI0_IRQ { IRQ_KMIINT0 }
+#define KMI1_IRQ { IRQ_KMIINT1 }
-static struct amba_device uart0_device = {
- .dev = {
- .init_name = "mb:16",
- .platform_data = &integrator_uart_data,
- },
- .res = {
- .start = INTEGRATOR_UART0_BASE,
- .end = INTEGRATOR_UART0_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_UARTINT0, NO_IRQ },
-};
+static AMBA_APB_DEVICE(rtc, "mb:15", 0,
+ INTEGRATOR_RTC_BASE, INTEGRATOR_RTC_IRQ, NULL);
-static struct amba_device uart1_device = {
- .dev = {
- .init_name = "mb:17",
- .platform_data = &integrator_uart_data,
- },
- .res = {
- .start = INTEGRATOR_UART1_BASE,
- .end = INTEGRATOR_UART1_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_UARTINT1, NO_IRQ },
-};
+static AMBA_APB_DEVICE(uart0, "mb:16", 0,
+ INTEGRATOR_UART0_BASE, INTEGRATOR_UART0_IRQ, &integrator_uart_data);
-static struct amba_device kmi0_device = {
- .dev = {
- .init_name = "mb:18",
- },
- .res = {
- .start = KMI0_BASE,
- .end = KMI0_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_KMIINT0, NO_IRQ },
-};
+static AMBA_APB_DEVICE(uart1, "mb:17", 0,
+ INTEGRATOR_UART1_BASE, INTEGRATOR_UART1_IRQ, &integrator_uart_data);
-static struct amba_device kmi1_device = {
- .dev = {
- .init_name = "mb:19",
- },
- .res = {
- .start = KMI1_BASE,
- .end = KMI1_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_KMIINT1, NO_IRQ },
-};
+static AMBA_APB_DEVICE(kmi0, "mb:18", 0, KMI0_BASE, KMI0_IRQ, NULL);
+static AMBA_APB_DEVICE(kmi1, "mb:19", 0, KMI1_BASE, KMI1_IRQ, NULL);
static struct amba_device *amba_devs[] __initdata = {
&rtc_device,
diff --git a/arch/arm/mach-integrator/impd1.c b/arch/arm/mach-integrator/impd1.c
index 8cbb75a..3e538da 100644
--- a/arch/arm/mach-integrator/impd1.c
+++ b/arch/arm/mach-integrator/impd1.c
@@ -401,24 +401,21 @@
pc_base = dev->resource.start + idev->offset;
- d = kzalloc(sizeof(struct amba_device), GFP_KERNEL);
+ d = amba_device_alloc(NULL, pc_base, SZ_4K);
if (!d)
continue;
dev_set_name(&d->dev, "lm%x:%5.5lx", dev->id, idev->offset >> 12);
d->dev.parent = &dev->dev;
- d->res.start = dev->resource.start + idev->offset;
- d->res.end = d->res.start + SZ_4K - 1;
- d->res.flags = IORESOURCE_MEM;
d->irq[0] = dev->irq;
d->irq[1] = dev->irq;
d->periphid = idev->id;
d->dev.platform_data = idev->platform_data;
- ret = amba_device_register(d, &dev->resource);
+ ret = amba_device_add(d, &dev->resource);
if (ret) {
dev_err(&d->dev, "unable to register device: %d\n", ret);
- kfree(d);
+ amba_device_put(d);
}
}
diff --git a/arch/arm/mach-integrator/include/mach/system.h b/arch/arm/mach-integrator/include/mach/system.h
deleted file mode 100644
index 901514e..0000000
--- a/arch/arm/mach-integrator/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-integrator/include/mach/system.h
- *
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-integrator/integrator_cp.c
index a8b6aa6..be9ead4 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-integrator/integrator_cp.c
@@ -347,32 +347,14 @@
.gpio_cd = -1,
};
-static struct amba_device mmc_device = {
- .dev = {
- .init_name = "mb:1c",
- .platform_data = &mmc_data,
- },
- .res = {
- .start = INTEGRATOR_CP_MMC_BASE,
- .end = INTEGRATOR_CP_MMC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 },
- .periphid = 0,
-};
+#define INTEGRATOR_CP_MMC_IRQS { IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 }
+#define INTEGRATOR_CP_AACI_IRQS { IRQ_CP_AACIINT }
-static struct amba_device aaci_device = {
- .dev = {
- .init_name = "mb:1d",
- },
- .res = {
- .start = INTEGRATOR_CP_AACI_BASE,
- .end = INTEGRATOR_CP_AACI_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_CP_AACIINT, NO_IRQ },
- .periphid = 0,
-};
+static AMBA_APB_DEVICE(mmc, "mb:1c", 0, INTEGRATOR_CP_MMC_BASE,
+ INTEGRATOR_CP_MMC_IRQS, &mmc_data);
+
+static AMBA_APB_DEVICE(aaci, "mb:1d", 0, INTEGRATOR_CP_AACI_BASE,
+ INTEGRATOR_CP_AACI_IRQS, NULL);
/*
@@ -425,21 +407,8 @@
.remove = versatile_clcd_remove_dma,
};
-static struct amba_device clcd_device = {
- .dev = {
- .init_name = "mb:c0",
- .coherent_dma_mask = ~0,
- .platform_data = &clcd_data,
- },
- .res = {
- .start = INTCP_PA_CLCD_BASE,
- .end = INTCP_PA_CLCD_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .dma_mask = ~0,
- .irq = { IRQ_CP_CLCDCINT, NO_IRQ },
- .periphid = 0,
-};
+static AMBA_AHB_DEVICE(clcd, "mb:c0", 0, INTCP_PA_CLCD_BASE,
+ { IRQ_CP_CLCDCINT }, &clcd_data);
static struct amba_device *amba_devs[] __initdata = {
&mmc_device,
diff --git a/arch/arm/mach-iop13xx/include/mach/system.h b/arch/arm/mach-iop13xx/include/mach/system.h
deleted file mode 100644
index 1f31ed3..0000000
--- a/arch/arm/mach-iop13xx/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop13xx/include/mach/system.h
- *
- * Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-iop32x/include/mach/system.h b/arch/arm/mach-iop32x/include/mach/system.h
deleted file mode 100644
index 4a88727..0000000
--- a/arch/arm/mach-iop32x/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop32x/include/mach/system.h
- *
- * Copyright (C) 2001 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-iop33x/include/mach/system.h b/arch/arm/mach-iop33x/include/mach/system.h
deleted file mode 100644
index 4f98e76..0000000
--- a/arch/arm/mach-iop33x/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-iop33x/include/mach/system.h
- *
- * Copyright (C) 2001 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-ixp2000/include/mach/system.h b/arch/arm/mach-ixp2000/include/mach/system.h
deleted file mode 100644
index a7fb08b..0000000
--- a/arch/arm/mach-ixp2000/include/mach/system.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/*
- * arch/arm/mach-ixp2000/include/mach/system.h
- *
- * Copyright (C) 2002 Intel Corp.
- * Copyricht (C) 2003-2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-ixp23xx/core.c b/arch/arm/mach-ixp23xx/core.c
index 0923bb9..7c1495e 100644
--- a/arch/arm/mach-ixp23xx/core.c
+++ b/arch/arm/mach-ixp23xx/core.c
@@ -441,6 +441,9 @@
void __init ixp23xx_sys_init(void)
{
+ /* by default, the idle code is disabled */
+ disable_hlt();
+
*IXP23XX_EXP_UNIT_FUSE |= 0xf;
platform_add_devices(ixp23xx_devices, ARRAY_SIZE(ixp23xx_devices));
}
diff --git a/arch/arm/mach-ixp23xx/include/mach/system.h b/arch/arm/mach-ixp23xx/include/mach/system.h
deleted file mode 100644
index 277dda7..0000000
--- a/arch/arm/mach-ixp23xx/include/mach/system.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * arch/arm/mach-ixp23xx/include/mach/system.h
- *
- * Copyright (C) 2003 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
-#if 0
- if (!hlt_counter)
- cpu_do_idle();
-#endif
-}
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
index 3841ab4..a6329a0 100644
--- a/arch/arm/mach-ixp4xx/common.c
+++ b/arch/arm/mach-ixp4xx/common.c
@@ -236,6 +236,12 @@
{
int i = 0;
+ /*
+ * ixp4xx does not implement the XScale PWRMODE register
+ * so it must not call cpu_do_idle().
+ */
+ disable_hlt();
+
/* Route all sources to IRQ instead of FIQ */
*IXP4XX_ICLR = 0x0;
diff --git a/arch/arm/mach-ixp4xx/include/mach/system.h b/arch/arm/mach-ixp4xx/include/mach/system.h
deleted file mode 100644
index 140a9be..0000000
--- a/arch/arm/mach-ixp4xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/include/mach/system.h
- *
- * Copyright (C) 2002 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-static inline void arch_idle(void)
-{
- /* ixp4xx does not implement the XScale PWRMODE register,
- * so it must not call cpu_do_idle() here.
- */
-#if 0
- cpu_do_idle();
-#endif
-}
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 7fc603b..90ceab7 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -44,6 +44,20 @@
Say 'Y' here if you want your kernel to support the
Marvell GuruPlug Reference Board.
+config ARCH_KIRKWOOD_DT
+ bool "Marvell Kirkwood Flattened Device Tree"
+ select USE_OF
+ help
+ Say 'Y' here if you want your kernel to support the
+ Marvell Kirkwood using flattened device tree.
+
+config MACH_DREAMPLUG_DT
+ bool "Marvell DreamPlug (Flattened Device Tree)"
+ select ARCH_KIRKWOOD_DT
+ help
+ Say 'Y' here if you want your kernel to support the
+ Marvell DreamPlug (Flattened Device Tree).
+
config MACH_TS219
bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
help
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index 5dcaa81..acbc5e1 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -20,3 +20,4 @@
obj-$(CONFIG_MACH_T5325) += t5325-setup.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
+obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
index 760a0ef..16f9385 100644
--- a/arch/arm/mach-kirkwood/Makefile.boot
+++ b/arch/arm/mach-kirkwood/Makefile.boot
@@ -1,3 +1,5 @@
zreladdr-y += 0x00008000
params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
+
+dtb-$(CONFIG_MACH_DREAMPLUG_DT) += kirkwood-dreamplug.dtb
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
new file mode 100644
index 0000000..fbe6405
--- /dev/null
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -0,0 +1,180 @@
+/*
+ * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
+ *
+ * arch/arm/mach-kirkwood/board-dt.c
+ *
+ * Marvell DreamPlug Reference Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct of_device_id kirkwood_dt_match_table[] __initdata = {
+ { .compatible = "simple-bus", },
+ { }
+};
+
+struct mtd_partition dreamplug_partitions[] = {
+ {
+ .name = "u-boot",
+ .size = SZ_512K,
+ .offset = 0,
+ },
+ {
+ .name = "u-boot env",
+ .size = SZ_64K,
+ .offset = SZ_512K + SZ_512K,
+ },
+ {
+ .name = "dtb",
+ .size = SZ_64K,
+ .offset = SZ_512K + SZ_512K + SZ_512K,
+ },
+};
+
+static const struct flash_platform_data dreamplug_spi_slave_data = {
+ .type = "mx25l1606e",
+ .name = "spi_flash",
+ .parts = dreamplug_partitions,
+ .nr_parts = ARRAY_SIZE(dreamplug_partitions),
+};
+
+static struct spi_board_info __initdata dreamplug_spi_slave_info[] = {
+ {
+ .modalias = "m25p80",
+ .platform_data = &dreamplug_spi_slave_data,
+ .irq = -1,
+ .max_speed_hz = 50000000,
+ .bus_num = 0,
+ .chip_select = 0,
+ },
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(1),
+};
+
+static struct mv_sata_platform_data dreamplug_sata_data = {
+ .n_ports = 1,
+};
+
+static struct mvsdio_platform_data dreamplug_mvsdio_data = {
+ /* unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led dreamplug_led_pins[] = {
+ {
+ .name = "dreamplug:blue:bluetooth",
+ .gpio = 47,
+ .active_low = 1,
+ },
+ {
+ .name = "dreamplug:green:wifi",
+ .gpio = 48,
+ .active_low = 1,
+ },
+ {
+ .name = "dreamplug:green:wifi_ap",
+ .gpio = 49,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data dreamplug_led_data = {
+ .leds = dreamplug_led_pins,
+ .num_leds = ARRAY_SIZE(dreamplug_led_pins),
+};
+
+static struct platform_device dreamplug_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &dreamplug_led_data,
+ }
+};
+
+static unsigned int dreamplug_mpp_config[] __initdata = {
+ MPP0_SPI_SCn,
+ MPP1_SPI_MOSI,
+ MPP2_SPI_SCK,
+ MPP3_SPI_MISO,
+ MPP47_GPIO, /* Bluetooth LED */
+ MPP48_GPIO, /* Wifi LED */
+ MPP49_GPIO, /* Wifi AP LED */
+ 0
+};
+
+static void __init dreamplug_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_mpp_conf(dreamplug_mpp_config);
+
+ spi_register_board_info(dreamplug_spi_slave_info,
+ ARRAY_SIZE(dreamplug_spi_slave_info));
+ kirkwood_spi_init();
+
+ kirkwood_ehci_init();
+ kirkwood_ge00_init(&dreamplug_ge00_data);
+ kirkwood_ge01_init(&dreamplug_ge01_data);
+ kirkwood_sata_init(&dreamplug_sata_data);
+ kirkwood_sdio_init(&dreamplug_mvsdio_data);
+
+ platform_device_register(&dreamplug_leds);
+}
+
+static void __init kirkwood_dt_init(void)
+{
+ kirkwood_init();
+
+ if (of_machine_is_compatible("globalscale,dreamplug"))
+ dreamplug_init();
+
+ of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL);
+}
+
+static const char *kirkwood_dt_board_compat[] = {
+ "globalscale,dreamplug",
+ NULL
+};
+
+DT_MACHINE_START(KIRKWOOD_DT, "Marvell Kirkwood (Flattened Device Tree)")
+ /* Maintainer: Jason Cooper <jason@lakedaemon.net> */
+ .map_io = kirkwood_map_io,
+ .init_early = kirkwood_init_early,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+ .init_machine = kirkwood_dt_init,
+ .restart = kirkwood_restart,
+ .dt_compat = kirkwood_dt_board_compat,
+MACHINE_END
diff --git a/arch/arm/mach-kirkwood/include/mach/system.h b/arch/arm/mach-kirkwood/include/mach/system.h
deleted file mode 100644
index 5fddde0..0000000
--- a/arch/arm/mach-kirkwood/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-ks8695/include/mach/system.h b/arch/arm/mach-ks8695/include/mach/system.h
deleted file mode 100644
index 59fe992..0000000
--- a/arch/arm/mach-ks8695/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-s3c2410/include/mach/system.h
- *
- * Copyright (C) 2006 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * KS8695 - System function defines and includes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks,
- */
- cpu_do_idle();
-
-}
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/include/mach/system.h b/arch/arm/mach-lpc32xx/include/mach/system.h
deleted file mode 100644
index bf176c9..0000000
--- a/arch/arm/mach-lpc32xx/include/mach/system.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/system.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bfee5b4..5d51c10 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -149,20 +149,8 @@
.remove = lpc32xx_clcd_remove,
};
-static struct amba_device lpc32xx_clcd_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "dev:clcd",
- .platform_data = &lpc32xx_clcd_data,
- },
- .res = {
- .start = LPC32XX_LCD_BASE,
- .end = (LPC32XX_LCD_BASE + SZ_4K - 1),
- .flags = IORESOURCE_MEM,
- },
- .dma_mask = ~0,
- .irq = {IRQ_LPC32XX_LCD, NO_IRQ},
-};
+static AMBA_AHB_DEVICE(lpc32xx_clcd, "dev:clcd", 0,
+ LPC32XX_LCD_BASE, { IRQ_LPC32XX_LCD }, &lpc32xx_clcd_data);
/*
* AMBA SSP (SPI)
@@ -191,20 +179,8 @@
.enable_dma = 0,
};
-static struct amba_device lpc32xx_ssp0_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "dev:ssp0",
- .platform_data = &lpc32xx_ssp0_data,
- },
- .res = {
- .start = LPC32XX_SSP0_BASE,
- .end = (LPC32XX_SSP0_BASE + SZ_4K - 1),
- .flags = IORESOURCE_MEM,
- },
- .dma_mask = ~0,
- .irq = {IRQ_LPC32XX_SSP0, NO_IRQ},
-};
+static AMBA_APB_DEVICE(lpc32xx_ssp0, "dev:ssp0", 0,
+ LPC32XX_SSP0_BASE, { IRQ_LPC32XX_SSP0 }, &lpc32xx_ssp0_data);
/* AT25 driver registration */
static int __init phy3250_spi_board_register(void)
diff --git a/arch/arm/mach-mmp/include/mach/system.h b/arch/arm/mach-mmp/include/mach/system.h
deleted file mode 100644
index 1d001ea..0000000
--- a/arch/arm/mach-mmp/include/mach/system.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * linux/arch/arm/mach-mmp/include/mach/system.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_MACH_SYSTEM_H
-#define __ASM_MACH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-#endif /* __ASM_MACH_SYSTEM_H */
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index 617c60a..c709a24 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -223,6 +223,7 @@
}, {
.start = IRQ_MMP2_GPIO,
.end = IRQ_MMP2_GPIO,
+ .name = "gpio_mux",
.flags = IORESOURCE_IRQ,
},
};
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index ada1213..f10f87d 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -166,6 +166,7 @@
}, {
.start = IRQ_PXA168_GPIOX,
.end = IRQ_PXA168_GPIOX,
+ .name = "gpio_mux",
.flags = IORESOURCE_IRQ,
},
};
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 3241a25..0c87e69 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -173,6 +173,7 @@
}, {
.start = IRQ_PXA910_AP_GPIO,
.end = IRQ_PXA910_AP_GPIO,
+ .name = "gpio_mux",
.flags = IORESOURCE_IRQ,
},
};
diff --git a/arch/arm/mach-msm/idle.S b/arch/arm/mach-msm/idle.S
deleted file mode 100644
index 6a94f05..0000000
--- a/arch/arm/mach-msm/idle.S
+++ /dev/null
@@ -1,36 +0,0 @@
-/* arch/arm/mach-msm/include/mach/idle.S
- *
- * Idle processing for MSM7K - work around bugs with SWFI.
- *
- * Copyright (c) 2007 QUALCOMM Incorporated.
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/linkage.h>
-#include <asm/assembler.h>
-
-ENTRY(arch_idle)
-#ifdef CONFIG_MSM7X00A_IDLE
- mrc p15, 0, r1, c1, c0, 0 /* read current CR */
- bic r0, r1, #(1 << 2) /* clear dcache bit */
- bic r0, r0, #(1 << 12) /* clear icache bit */
- mcr p15, 0, r0, c1, c0, 0 /* disable d/i cache */
-
- mov r0, #0 /* prepare wfi value */
- mcr p15, 0, r0, c7, c10, 0 /* flush the cache */
- mcr p15, 0, r0, c7, c10, 4 /* memory barrier */
- mcr p15, 0, r0, c7, c0, 4 /* wait for interrupt */
-
- mcr p15, 0, r1, c1, c0, 0 /* restore d/i cache */
-#endif
- mov pc, lr
diff --git a/arch/arm/mach-msm/idle.c b/arch/arm/mach-msm/idle.c
new file mode 100644
index 0000000..0c9e13c
--- /dev/null
+++ b/arch/arm/mach-msm/idle.c
@@ -0,0 +1,49 @@
+/* arch/arm/mach-msm/idle.c
+ *
+ * Idle processing for MSM7K - work around bugs with SWFI.
+ *
+ * Copyright (c) 2007 QUALCOMM Incorporated.
+ * Copyright (C) 2007 Google, Inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/init.h>
+#include <asm/system.h>
+
+static void msm_idle(void)
+{
+#ifdef CONFIG_MSM7X00A_IDLE
+ asm volatile (
+
+ "mrc p15, 0, r1, c1, c0, 0 /* read current CR */ \n\t"
+ "bic r0, r1, #(1 << 2) /* clear dcache bit */ \n\t"
+ "bic r0, r0, #(1 << 12) /* clear icache bit */ \n\t"
+ "mcr p15, 0, r0, c1, c0, 0 /* disable d/i cache */ \n\t"
+
+ "mov r0, #0 /* prepare wfi value */ \n\t"
+ "mcr p15, 0, r0, c7, c10, 0 /* flush the cache */ \n\t"
+ "mcr p15, 0, r0, c7, c10, 4 /* memory barrier */ \n\t"
+ "mcr p15, 0, r0, c7, c0, 4 /* wait for interrupt */ \n\t"
+
+ "mcr p15, 0, r1, c1, c0, 0 /* restore d/i cache */ \n\t"
+
+ : : : "r0","r1" );
+#endif
+}
+
+static int __init msm_idle_init(void)
+{
+ arm_pm_idle = msm_idle;
+ return 0;
+}
+
+arch_initcall(msm_idle_init);
diff --git a/arch/arm/mach-msm/include/mach/system.h b/arch/arm/mach-msm/include/mach/system.h
index 311db2b..f5fb2ec 100644
--- a/arch/arm/mach-msm/include/mach/system.h
+++ b/arch/arm/mach-msm/include/mach/system.h
@@ -12,7 +12,6 @@
* GNU General Public License for more details.
*
*/
-void arch_idle(void);
/* low level hardware reset hook -- for example, hitting the
* PSHOLD line on the PMIC to hard reset the system
diff --git a/arch/arm/mach-mv78xx0/include/mach/system.h b/arch/arm/mach-mv78xx0/include/mach/system.h
deleted file mode 100644
index 8c3a538..0000000
--- a/arch/arm/mach-mv78xx0/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-mv78xx0/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index cf00b3e..c57f996 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -83,6 +83,18 @@
select MXS_HAVE_PLATFORM_MXSFB
select MXS_OCOTP
+config MODULE_APX4
+ bool
+ select SOC_IMX28
+ select LEDS_GPIO_REGISTER
+ select MXS_HAVE_AMBA_DUART
+ select MXS_HAVE_PLATFORM_AUART
+ select MXS_HAVE_PLATFORM_FEC
+ select MXS_HAVE_PLATFORM_MXS_I2C
+ select MXS_HAVE_PLATFORM_MXS_MMC
+ select MXS_HAVE_PLATFORM_MXS_SAIF
+ select MXS_OCOTP
+
config MACH_TX28
bool "Ka-Ro TX28 module"
select MODULE_TX28
@@ -91,4 +103,8 @@
bool "Support DENX M28EVK Platform"
select MODULE_M28
+config MACH_APX4DEVKIT
+ bool "Support Bluegiga APX4 Development Kit"
+ select MODULE_APX4
+
endif
diff --git a/arch/arm/mach-mxs/Makefile b/arch/arm/mach-mxs/Makefile
index 8c93b24..908bf9a 100644
--- a/arch/arm/mach-mxs/Makefile
+++ b/arch/arm/mach-mxs/Makefile
@@ -11,6 +11,7 @@
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
obj-$(CONFIG_MACH_M28EVK) += mach-m28evk.o
+obj-$(CONFIG_MACH_APX4DEVKIT) += mach-apx4devkit.o
obj-$(CONFIG_MODULE_TX28) += module-tx28.o
obj-$(CONFIG_MACH_TX28) += mach-tx28.o
diff --git a/arch/arm/mach-mxs/devices.c b/arch/arm/mach-mxs/devices.c
index fe3e847..01faffe 100644
--- a/arch/arm/mach-mxs/devices.c
+++ b/arch/arm/mach-mxs/devices.c
@@ -77,16 +77,18 @@
int __init mxs_add_amba_device(const struct amba_device *dev)
{
- struct amba_device *adev = kmalloc(sizeof(*adev), GFP_KERNEL);
+ struct amba_device *adev = amba_device_alloc(dev->dev.init_name,
+ dev->res.start, resource_size(&dev->res));
if (!adev) {
pr_err("%s: failed to allocate memory", __func__);
return -ENOMEM;
}
- *adev = *dev;
+ adev->irq[0] = dev->irq[0];
+ adev->irq[1] = dev->irq[1];
- return amba_device_register(adev, &iomem_resource);
+ return amba_device_add(adev, &iomem_resource);
}
struct device mxs_apbh_bus = {
diff --git a/arch/arm/mach-mxs/devices/amba-duart.c b/arch/arm/mach-mxs/devices/amba-duart.c
index a559db0..a5479f7 100644
--- a/arch/arm/mach-mxs/devices/amba-duart.c
+++ b/arch/arm/mach-mxs/devices/amba-duart.c
@@ -23,7 +23,7 @@
.end = (soc ## _DUART_BASE_ADDR) + SZ_8K - 1, \
.flags = IORESOURCE_MEM, \
}, \
- .irq = {soc ## _INT_DUART, NO_IRQ}, \
+ .irq = {soc ## _INT_DUART}, \
}
#ifdef CONFIG_SOC_IMX23
diff --git a/arch/arm/mach-mxs/include/mach/digctl.h b/arch/arm/mach-mxs/include/mach/digctl.h
index 49a888c..1796406 100644
--- a/arch/arm/mach-mxs/include/mach/digctl.h
+++ b/arch/arm/mach-mxs/include/mach/digctl.h
@@ -18,4 +18,5 @@
#define HW_DIGCTL_CTRL 0x0
#define BP_DIGCTL_CTRL_SAIF_CLKMUX 10
#define BM_DIGCTL_CTRL_SAIF_CLKMUX (0x3 << 10)
+#define HW_DIGCTL_CHIPID 0x310
#endif
diff --git a/arch/arm/mach-mxs/include/mach/mxs.h b/arch/arm/mach-mxs/include/mach/mxs.h
index bde5f66..7d4fb6d 100644
--- a/arch/arm/mach-mxs/include/mach/mxs.h
+++ b/arch/arm/mach-mxs/include/mach/mxs.h
@@ -23,22 +23,10 @@
#include <linux/io.h>
#endif
#include <asm/mach-types.h>
+#include <mach/digctl.h>
#include <mach/hardware.h>
/*
- * MXS CPU types
- */
-#define cpu_is_mx23() ( \
- machine_is_mx23evk() || \
- machine_is_stmp378x() || \
- 0)
-#define cpu_is_mx28() ( \
- machine_is_mx28evk() || \
- machine_is_m28evk() || \
- machine_is_tx28() || \
- 0)
-
-/*
* IO addresses common to MXS-based
*/
#define MXS_IO_BASE_ADDR 0x80000000
@@ -109,6 +97,21 @@
{
__raw_writel(mask, reg + MXS_TOG_ADDR);
}
+
+/*
+ * MXS CPU types
+ */
+#define MXS_CHIPID (MXS_IO_ADDRESS(MXS_DIGCTL_BASE_ADDR) + HW_DIGCTL_CHIPID)
+
+static inline int cpu_is_mx23(void)
+{
+ return ((__raw_readl(MXS_CHIPID) >> 16) == 0x3780);
+}
+
+static inline int cpu_is_mx28(void)
+{
+ return ((__raw_readl(MXS_CHIPID) >> 16) == 0x2800);
+}
#endif
#endif /* __MACH_MXS_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/system.h b/arch/arm/mach-mxs/include/mach/system.h
deleted file mode 100644
index e7ad1bb..0000000
--- a/arch/arm/mach-mxs/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright 2004-2008 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_MXS_SYSTEM_H__
-#define __MACH_MXS_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif /* __MACH_MXS_SYSTEM_H__ */
diff --git a/arch/arm/mach-mxs/include/mach/uncompress.h b/arch/arm/mach-mxs/include/mach/uncompress.h
index 6777674..ef28114 100644
--- a/arch/arm/mach-mxs/include/mach/uncompress.h
+++ b/arch/arm/mach-mxs/include/mach/uncompress.h
@@ -18,8 +18,6 @@
#ifndef __MACH_MXS_UNCOMPRESS_H__
#define __MACH_MXS_UNCOMPRESS_H__
-#include <asm/mach-types.h>
-
unsigned long mxs_duart_base;
#define MXS_DUART(x) (*(volatile unsigned long *)(mxs_duart_base + (x)))
@@ -55,16 +53,17 @@
#define MX23_DUART_BASE_ADDR 0x80070000
#define MX28_DUART_BASE_ADDR 0x80074000
+#define MXS_DIGCTL_CHIPID 0x8001c310
static inline void __arch_decomp_setup(unsigned long arch_id)
{
- switch (arch_id) {
- case MACH_TYPE_MX23EVK:
+ u16 chipid = (*(volatile unsigned long *) MXS_DIGCTL_CHIPID) >> 16;
+
+ switch (chipid) {
+ case 0x3780:
mxs_duart_base = MX23_DUART_BASE_ADDR;
break;
- case MACH_TYPE_MX28EVK:
- case MACH_TYPE_M28EVK:
- case MACH_TYPE_TX28:
+ case 0x2800:
mxs_duart_base = MX28_DUART_BASE_ADDR;
break;
default:
diff --git a/arch/arm/mach-mxs/mach-apx4devkit.c b/arch/arm/mach-mxs/mach-apx4devkit.c
new file mode 100644
index 0000000..48a7fab
--- /dev/null
+++ b/arch/arm/mach-mxs/mach-apx4devkit.c
@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2011-2012
+ * Lauri Hintsala, Bluegiga, <lauri.hintsala@bluegiga.com>
+ * Veli-Pekka Peltola, Bluegiga, <veli-pekka.peltola@bluegiga.com>
+ *
+ * based on: mach-mx28evk.c
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/micrel_phy.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/digctl.h>
+#include <mach/iomux-mx28.h>
+
+#include "devices-mx28.h"
+
+#define APX4DEVKIT_GPIO_USERLED MXS_GPIO_NR(3, 28)
+
+static const iomux_cfg_t apx4devkit_pads[] __initconst = {
+ /* duart */
+ MX28_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
+ MX28_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
+
+ /* auart0 */
+ MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
+ MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
+ MX28_PAD_AUART0_CTS__AUART0_CTS | MXS_PAD_CTRL,
+ MX28_PAD_AUART0_RTS__AUART0_RTS | MXS_PAD_CTRL,
+
+ /* auart1 */
+ MX28_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
+ MX28_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
+
+ /* auart2 */
+ MX28_PAD_SSP2_SCK__AUART2_RX | MXS_PAD_CTRL,
+ MX28_PAD_SSP2_MOSI__AUART2_TX | MXS_PAD_CTRL,
+
+ /* auart3 */
+ MX28_PAD_SSP2_MISO__AUART3_RX | MXS_PAD_CTRL,
+ MX28_PAD_SSP2_SS0__AUART3_TX | MXS_PAD_CTRL,
+
+#define MXS_PAD_FEC (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
+ /* fec0 */
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
+
+ /* i2c */
+ MX28_PAD_I2C0_SCL__I2C0_SCL,
+ MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+ /* mmc0 */
+ MX28_PAD_SSP0_DATA0__SSP0_D0 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA1__SSP0_D1 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA2__SSP0_D2 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA3__SSP0_D3 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA4__SSP0_D4 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA5__SSP0_D5 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA6__SSP0_D6 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA7__SSP0_D7 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_CMD__SSP0_CMD |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ MX28_PAD_SSP0_SCK__SSP0_SCK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+ /* led */
+ MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
+
+ /* saif0 & saif1 */
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+};
+
+/* led */
+static const struct gpio_led apx4devkit_leds[] __initconst = {
+ {
+ .name = "user-led",
+ .default_trigger = "heartbeat",
+ .gpio = APX4DEVKIT_GPIO_USERLED,
+ },
+};
+
+static const struct gpio_led_platform_data apx4devkit_led_data __initconst = {
+ .leds = apx4devkit_leds,
+ .num_leds = ARRAY_SIZE(apx4devkit_leds),
+};
+
+static const struct fec_platform_data mx28_fec_pdata __initconst = {
+ .phy = PHY_INTERFACE_MODE_RMII,
+};
+
+static const struct mxs_mmc_platform_data apx4devkit_mmc_pdata __initconst = {
+ .wp_gpio = -EINVAL,
+ .flags = SLOTF_4_BIT_CAPABLE,
+};
+
+static const struct i2c_board_info apx4devkit_i2c_boardinfo[] __initconst = {
+ { I2C_BOARD_INFO("sgtl5000", 0x0a) }, /* ASoC */
+ { I2C_BOARD_INFO("pcf8563", 0x51) }, /* RTC */
+};
+
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || \
+ defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+static struct regulator_consumer_supply apx4devkit_audio_consumer_supplies[] = {
+ REGULATOR_SUPPLY("VDDA", "0-000a"),
+ REGULATOR_SUPPLY("VDDIO", "0-000a"),
+};
+
+static struct regulator_init_data apx4devkit_vdd_reg_init_data = {
+ .constraints = {
+ .name = "3V3",
+ .always_on = 1,
+ },
+ .consumer_supplies = apx4devkit_audio_consumer_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(apx4devkit_audio_consumer_supplies),
+};
+
+static struct fixed_voltage_config apx4devkit_vdd_pdata = {
+ .supply_name = "board-3V3",
+ .microvolts = 3300000,
+ .gpio = -EINVAL,
+ .enabled_at_boot = 1,
+ .init_data = &apx4devkit_vdd_reg_init_data,
+};
+
+static struct platform_device apx4devkit_voltage_regulator = {
+ .name = "reg-fixed-voltage",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &apx4devkit_vdd_pdata,
+ },
+};
+
+static void __init apx4devkit_add_regulators(void)
+{
+ platform_device_register(&apx4devkit_voltage_regulator);
+}
+#else
+static void __init apx4devkit_add_regulators(void) {}
+#endif
+
+static const struct mxs_saif_platform_data
+ apx4devkit_mxs_saif_pdata[] __initconst = {
+ /* working on EXTMSTR0 mode (saif0 master, saif1 slave) */
+ {
+ .master_mode = 1,
+ .master_id = 0,
+ }, {
+ .master_mode = 0,
+ .master_id = 0,
+ },
+};
+
+static int apx4devkit_phy_fixup(struct phy_device *phy)
+{
+ phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
+ return 0;
+}
+
+static void __init apx4devkit_init(void)
+{
+ mxs_iomux_setup_multiple_pads(apx4devkit_pads,
+ ARRAY_SIZE(apx4devkit_pads));
+
+ mx28_add_duart();
+ mx28_add_auart0();
+ mx28_add_auart1();
+ mx28_add_auart2();
+ mx28_add_auart3();
+
+ /*
+ * Register fixup for the Micrel KS8031 PHY clock
+ * (shares same ID with KS8051)
+ */
+ phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
+ apx4devkit_phy_fixup);
+
+ mx28_add_fec(0, &mx28_fec_pdata);
+
+ mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);
+
+ gpio_led_register_device(0, &apx4devkit_led_data);
+
+ mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
+ mx28_add_saif(0, &apx4devkit_mxs_saif_pdata[0]);
+ mx28_add_saif(1, &apx4devkit_mxs_saif_pdata[1]);
+
+ apx4devkit_add_regulators();
+
+ mx28_add_mxs_i2c(0);
+ i2c_register_board_info(0, apx4devkit_i2c_boardinfo,
+ ARRAY_SIZE(apx4devkit_i2c_boardinfo));
+
+ mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0, NULL, 0);
+}
+
+static void __init apx4devkit_timer_init(void)
+{
+ mx28_clocks_init();
+}
+
+static struct sys_timer apx4devkit_timer = {
+ .init = apx4devkit_timer_init,
+};
+
+MACHINE_START(APX4DEVKIT, "Bluegiga APX4 Development Kit")
+ .map_io = mx28_map_io,
+ .init_irq = mx28_init_irq,
+ .timer = &apx4devkit_timer,
+ .init_machine = apx4devkit_init,
+ .restart = mxs_restart,
+MACHINE_END
diff --git a/arch/arm/mach-mxs/mach-m28evk.c b/arch/arm/mach-mxs/mach-m28evk.c
index 2f27582..06d7996 100644
--- a/arch/arm/mach-mxs/mach-m28evk.c
+++ b/arch/arm/mach-mxs/mach-m28evk.c
@@ -247,18 +247,15 @@
u32 val;
const u32 *ocotp = mxs_get_ocotp();
- if (!ocotp) {
- pr_err("%s: timeout when reading fec mac from OCOTP\n",
- __func__);
+ if (!ocotp)
return -ETIMEDOUT;
- }
/*
* OCOTP only stores the last 4 octets for each mac address,
* so hard-code DENX OUI (C0:E5:4E) here.
*/
for (i = 0; i < 2; i++) {
- val = ocotp[i * 4];
+ val = ocotp[i];
mx28_fec_pdata[i].mac[0] = 0xC0;
mx28_fec_pdata[i].mac[1] = 0xE5;
mx28_fec_pdata[i].mac[2] = 0x4E;
diff --git a/arch/arm/mach-mxs/mach-mx28evk.c b/arch/arm/mach-mxs/mach-mx28evk.c
index fdb0a56..e386c14 100644
--- a/arch/arm/mach-mxs/mach-mx28evk.c
+++ b/arch/arm/mach-mxs/mach-mx28evk.c
@@ -223,7 +223,6 @@
/* fec */
static void __init mx28evk_fec_reset(void)
{
- int ret;
struct clk *clk;
/* Enable fec phy clock */
@@ -231,32 +230,7 @@
if (!IS_ERR(clk))
clk_prepare_enable(clk);
- /* Power up fec phy */
- ret = gpio_request(MX28EVK_FEC_PHY_POWER, "fec-phy-power");
- if (ret) {
- pr_err("Failed to request gpio fec-phy-%s: %d\n", "power", ret);
- return;
- }
-
- ret = gpio_direction_output(MX28EVK_FEC_PHY_POWER, 0);
- if (ret) {
- pr_err("Failed to drive gpio fec-phy-%s: %d\n", "power", ret);
- return;
- }
-
- /* Reset fec phy */
- ret = gpio_request(MX28EVK_FEC_PHY_RESET, "fec-phy-reset");
- if (ret) {
- pr_err("Failed to request gpio fec-phy-%s: %d\n", "reset", ret);
- return;
- }
-
- gpio_direction_output(MX28EVK_FEC_PHY_RESET, 0);
- if (ret) {
- pr_err("Failed to drive gpio fec-phy-%s: %d\n", "reset", ret);
- return;
- }
-
+ gpio_set_value(MX28EVK_FEC_PHY_RESET, 0);
mdelay(1);
gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
}
@@ -278,14 +252,14 @@
const u32 *ocotp = mxs_get_ocotp();
if (!ocotp)
- goto error;
+ return -ETIMEDOUT;
/*
* OCOTP only stores the last 4 octets for each mac address,
* so hard-code Freescale OUI (00:04:9f) here.
*/
for (i = 0; i < 2; i++) {
- val = ocotp[i * 4];
+ val = ocotp[i];
mx28_fec_pdata[i].mac[0] = 0x00;
mx28_fec_pdata[i].mac[1] = 0x04;
mx28_fec_pdata[i].mac[2] = 0x9f;
@@ -295,10 +269,6 @@
}
return 0;
-
-error:
- pr_err("%s: timeout when reading fec mac from OCOTP\n", __func__);
- return -ETIMEDOUT;
}
/*
@@ -417,9 +387,14 @@
static void __init mx28evk_add_regulators(void) {}
#endif
-static struct gpio mx28evk_lcd_gpios[] = {
+static const struct gpio mx28evk_gpios[] __initconst = {
{ MX28EVK_LCD_ENABLE, GPIOF_OUT_INIT_HIGH, "lcd-enable" },
{ MX28EVK_BL_ENABLE, GPIOF_OUT_INIT_HIGH, "bl-enable" },
+ { MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT, "flexcan-switch" },
+ { MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc0-slot-power" },
+ { MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc1-slot-power" },
+ { MX28EVK_FEC_PHY_POWER, GPIOF_OUT_INIT_LOW, "fec-phy-power" },
+ { MX28EVK_FEC_PHY_RESET, GPIOF_DIR_OUT, "fec-phy-reset" },
};
static const struct mxs_saif_platform_data
@@ -447,25 +422,18 @@
if (mx28evk_fec_get_mac())
pr_warn("%s: failed on fec mac setup\n", __func__);
+ ret = gpio_request_array(mx28evk_gpios, ARRAY_SIZE(mx28evk_gpios));
+ if (ret)
+ pr_err("One or more GPIOs failed to be requested: %d\n", ret);
+
mx28evk_fec_reset();
mx28_add_fec(0, &mx28_fec_pdata[0]);
mx28_add_fec(1, &mx28_fec_pdata[1]);
- ret = gpio_request_one(MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT,
- "flexcan-switch");
- if (ret) {
- pr_err("failed to request gpio flexcan-switch: %d\n", ret);
- } else {
- mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
- mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
- }
+ mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
+ mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
- ret = gpio_request_array(mx28evk_lcd_gpios,
- ARRAY_SIZE(mx28evk_lcd_gpios));
- if (ret)
- pr_warn("failed to request gpio pins for lcd: %d\n", ret);
- else
- mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
+ mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
mx28_add_saif(0, &mx28evk_mxs_saif_pdata[0]);
@@ -480,20 +448,8 @@
mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0,
NULL, 0);
- /* power on mmc slot by writing 0 to the gpio */
- ret = gpio_request_one(MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW,
- "mmc0-slot-power");
- if (ret)
- pr_warn("failed to request gpio mmc0-slot-power: %d\n", ret);
- else
- mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
-
- ret = gpio_request_one(MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW,
- "mmc1-slot-power");
- if (ret)
- pr_warn("failed to request gpio mmc1-slot-power: %d\n", ret);
- else
- mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
+ mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
+ mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
mx28_add_rtc_stmp3xxx();
diff --git a/arch/arm/mach-mxs/pm.c b/arch/arm/mach-mxs/pm.c
index fb042da..a9b4bbc 100644
--- a/arch/arm/mach-mxs/pm.c
+++ b/arch/arm/mach-mxs/pm.c
@@ -15,13 +15,12 @@
#include <linux/kernel.h>
#include <linux/suspend.h>
#include <linux/io.h>
-#include <mach/system.h>
static int mxs_suspend_enter(suspend_state_t state)
{
switch (state) {
case PM_SUSPEND_MEM:
- arch_idle();
+ cpu_do_idle();
break;
default:
diff --git a/arch/arm/mach-netx/fb.c b/arch/arm/mach-netx/fb.c
index b991323..2cdf6ef 100644
--- a/arch/arm/mach-netx/fb.c
+++ b/arch/arm/mach-netx/fb.c
@@ -92,18 +92,7 @@
{
}
-static struct amba_device fb_device = {
- .dev = {
- .init_name = "fb",
- .coherent_dma_mask = ~0,
- },
- .res = {
- .start = 0x00104000,
- .end = 0x00104fff,
- .flags = IORESOURCE_MEM,
- },
- .irq = { NETX_IRQ_LCD, NO_IRQ },
-};
+static AMBA_AHB_DEVICE(fb, "fb", 0, 0x00104000, { NETX_IRQ_LCD }, NULL);
int netx_fb_init(struct clcd_board *board, struct clcd_panel *panel)
{
diff --git a/arch/arm/mach-netx/include/mach/system.h b/arch/arm/mach-netx/include/mach/system.h
deleted file mode 100644
index b38fa36..0000000
--- a/arch/arm/mach-netx/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-netx/include/mach/system.h
- *
- * Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
-
diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c
index 7c878bf..f6f74ad 100644
--- a/arch/arm/mach-nomadik/board-nhk8815.c
+++ b/arch/arm/mach-nomadik/board-nhk8815.c
@@ -185,20 +185,11 @@
#endif
}
-#define __MEM_4K_RESOURCE(x) \
- .res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM}
+static AMBA_APB_DEVICE(uart0, "uart0", 0, NOMADIK_UART0_BASE,
+ { IRQ_UART0 }, NULL);
-static struct amba_device uart0_device = {
- .dev = { .init_name = "uart0" },
- __MEM_4K_RESOURCE(NOMADIK_UART0_BASE),
- .irq = {IRQ_UART0, NO_IRQ},
-};
-
-static struct amba_device uart1_device = {
- .dev = { .init_name = "uart1" },
- __MEM_4K_RESOURCE(NOMADIK_UART1_BASE),
- .irq = {IRQ_UART1, NO_IRQ},
-};
+static AMBA_APB_DEVICE(uart1, "uart1", 0, NOMADIK_UART1_BASE,
+ { IRQ_UART1 }, NULL);
static struct amba_device *amba_devs[] __initdata = {
&uart0_device,
diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c
index 65df7b4..27f43a4 100644
--- a/arch/arm/mach-nomadik/cpu-8815.c
+++ b/arch/arm/mach-nomadik/cpu-8815.c
@@ -97,12 +97,7 @@
GPIO_DEVICE(3),
};
-static struct amba_device cpu8815_amba_rng = {
- .dev = {
- .init_name = "rng",
- },
- __MEM_4K_RESOURCE(NOMADIK_RNG_BASE),
-};
+static AMBA_APB_DEVICE(cpu8815_amba_rng, "rng", 0, NOMADIK_RNG_BASE, { }, NULL);
static struct platform_device *platform_devs[] __initdata = {
cpu8815_platform_gpio + 0,
@@ -112,7 +107,7 @@
};
static struct amba_device *amba_devs[] __initdata = {
- &cpu8815_amba_rng
+ &cpu8815_amba_rng_device
};
static int __init cpu8815_init(void)
diff --git a/arch/arm/mach-nomadik/include/mach/system.h b/arch/arm/mach-nomadik/include/mach/system.h
deleted file mode 100644
index 25e198b..0000000
--- a/arch/arm/mach-nomadik/include/mach/system.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * mach-nomadik/include/mach/system.h
- *
- * Copyright (C) 2008 STMicroelectronics
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index 4f8d66f..4b6a774 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -155,6 +155,10 @@
bool "Amstrad E3 (Delta)"
depends on ARCH_OMAP1 && ARCH_OMAP15XX
select FIQ
+ select GPIO_GENERIC_PLATFORM
+ select LEDS_GPIO_REGISTER
+ select REGULATOR
+ select REGULATOR_FIXED_VOLTAGE
help
Support for the Amstrad E3 (codename Delta) videophone. Say Y here
if you have such a device.
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 88909cc..cb6afe6 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -11,6 +11,7 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/basic_mmio_gpio.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
@@ -18,6 +19,9 @@
#include <linux/interrupt.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <linux/serial_8250.h>
#include <linux/export.h>
@@ -40,9 +44,6 @@
#include <mach/ams-delta-fiq.h>
-static u8 ams_delta_latch1_reg;
-static u16 ams_delta_latch2_reg;
-
static const unsigned int ams_delta_keymap[] = {
KEY(0, 0, KEY_F1), /* Advert */
@@ -121,49 +122,42 @@
KEY(7, 3, KEY_LEFTCTRL), /* Vol down */
};
-void ams_delta_latch1_write(u8 mask, u8 value)
-{
- ams_delta_latch1_reg &= ~mask;
- ams_delta_latch1_reg |= value;
- *(volatile __u8 *) AMS_DELTA_LATCH1_VIRT = ams_delta_latch1_reg;
-}
-
-void ams_delta_latch2_write(u16 mask, u16 value)
-{
- ams_delta_latch2_reg &= ~mask;
- ams_delta_latch2_reg |= value;
- *(volatile __u16 *) AMS_DELTA_LATCH2_VIRT = ams_delta_latch2_reg;
-}
+#define LATCH1_PHYS 0x01000000
+#define LATCH1_VIRT 0xEA000000
+#define MODEM_PHYS 0x04000000
+#define MODEM_VIRT 0xEB000000
+#define LATCH2_PHYS 0x08000000
+#define LATCH2_VIRT 0xEC000000
static struct map_desc ams_delta_io_desc[] __initdata = {
/* AMS_DELTA_LATCH1 */
{
- .virtual = AMS_DELTA_LATCH1_VIRT,
- .pfn = __phys_to_pfn(AMS_DELTA_LATCH1_PHYS),
+ .virtual = LATCH1_VIRT,
+ .pfn = __phys_to_pfn(LATCH1_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
},
/* AMS_DELTA_LATCH2 */
{
- .virtual = AMS_DELTA_LATCH2_VIRT,
- .pfn = __phys_to_pfn(AMS_DELTA_LATCH2_PHYS),
+ .virtual = LATCH2_VIRT,
+ .pfn = __phys_to_pfn(LATCH2_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
},
/* AMS_DELTA_MODEM */
{
- .virtual = AMS_DELTA_MODEM_VIRT,
- .pfn = __phys_to_pfn(AMS_DELTA_MODEM_PHYS),
+ .virtual = MODEM_VIRT,
+ .pfn = __phys_to_pfn(MODEM_PHYS),
.length = 0x01000000,
.type = MT_DEVICE
}
};
-static struct omap_lcd_config ams_delta_lcd_config = {
+static struct omap_lcd_config ams_delta_lcd_config __initdata = {
.ctrl_name = "internal",
};
-static struct omap_usb_config ams_delta_usb_config __initdata = {
+static struct omap_usb_config ams_delta_usb_config = {
.register_host = 1,
.hmc_mode = 16,
.pins[0] = 2,
@@ -173,6 +167,147 @@
{ OMAP_TAG_LCD, &ams_delta_lcd_config },
};
+#define LATCH1_GPIO_BASE 232
+#define LATCH1_NGPIO 8
+
+static struct resource latch1_resources[] = {
+ [0] = {
+ .name = "dat",
+ .start = LATCH1_PHYS,
+ .end = LATCH1_PHYS + (LATCH1_NGPIO - 1) / 8,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct bgpio_pdata latch1_pdata = {
+ .base = LATCH1_GPIO_BASE,
+ .ngpio = LATCH1_NGPIO,
+};
+
+static struct platform_device latch1_gpio_device = {
+ .name = "basic-mmio-gpio",
+ .id = 0,
+ .resource = latch1_resources,
+ .num_resources = ARRAY_SIZE(latch1_resources),
+ .dev = {
+ .platform_data = &latch1_pdata,
+ },
+};
+
+static struct resource latch2_resources[] = {
+ [0] = {
+ .name = "dat",
+ .start = LATCH2_PHYS,
+ .end = LATCH2_PHYS + (AMS_DELTA_LATCH2_NGPIO - 1) / 8,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct bgpio_pdata latch2_pdata = {
+ .base = AMS_DELTA_LATCH2_GPIO_BASE,
+ .ngpio = AMS_DELTA_LATCH2_NGPIO,
+};
+
+static struct platform_device latch2_gpio_device = {
+ .name = "basic-mmio-gpio",
+ .id = 1,
+ .resource = latch2_resources,
+ .num_resources = ARRAY_SIZE(latch2_resources),
+ .dev = {
+ .platform_data = &latch2_pdata,
+ },
+};
+
+static const struct gpio latch_gpios[] __initconst = {
+ {
+ .gpio = LATCH1_GPIO_BASE + 6,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "dockit1",
+ },
+ {
+ .gpio = LATCH1_GPIO_BASE + 7,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "dockit2",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "scard_rstin",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_SCARD_CMDVCC,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "scard_cmdvcc",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "modem_codec",
+ },
+ {
+ .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "hookflash1",
+ },
+ {
+ .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 15,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "hookflash2",
+ },
+};
+
+static struct regulator_consumer_supply modem_nreset_consumers[] = {
+ REGULATOR_SUPPLY("RESET#", "serial8250.1"),
+ REGULATOR_SUPPLY("POR", "cx20442-codec"),
+};
+
+static struct regulator_init_data modem_nreset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(modem_nreset_consumers),
+ .consumer_supplies = modem_nreset_consumers,
+};
+
+static struct fixed_voltage_config modem_nreset_config = {
+ .supply_name = "modem_nreset",
+ .microvolts = 3300000,
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
+ .startup_delay = 25000,
+ .enable_high = 1,
+ .enabled_at_boot = 1,
+ .init_data = &modem_nreset_data,
+};
+
+static struct platform_device modem_nreset_device = {
+ .name = "reg-fixed-voltage",
+ .id = -1,
+ .dev = {
+ .platform_data = &modem_nreset_config,
+ },
+};
+
+struct modem_private_data {
+ struct regulator *regulator;
+};
+
+static struct modem_private_data modem_priv;
+
+void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
+{
+ int bit = 0;
+ u16 bitpos = 1 << bit;
+
+ for (; bit < ngpio; bit++, bitpos = bitpos << 1) {
+ if (!(mask & bitpos))
+ continue;
+ else
+ gpio_set_value(base + bit, (value & bitpos) != 0);
+ }
+}
+EXPORT_SYMBOL(ams_delta_latch_write);
+
static struct resource ams_delta_nand_resources[] = {
[0] = {
.start = OMAP1_MPUIO_BASE,
@@ -202,7 +337,7 @@
.keymap_size = ARRAY_SIZE(ams_delta_keymap),
};
-static struct omap_kp_platform_data ams_delta_kp_data __initdata = {
+static struct omap_kp_platform_data ams_delta_kp_data = {
.rows = 8,
.cols = 8,
.keymap_data = &ams_delta_keymap_data,
@@ -224,9 +359,45 @@
.id = -1,
};
-static struct platform_device ams_delta_led_device = {
- .name = "ams-delta-led",
- .id = -1
+static const struct gpio_led gpio_leds[] __initconst = {
+ {
+ .name = "camera",
+ .gpio = LATCH1_GPIO_BASE + 0,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+#ifdef CONFIG_LEDS_TRIGGERS
+ .default_trigger = "ams_delta_camera",
+#endif
+ },
+ {
+ .name = "advert",
+ .gpio = LATCH1_GPIO_BASE + 1,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "email",
+ .gpio = LATCH1_GPIO_BASE + 2,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "handsfree",
+ .gpio = LATCH1_GPIO_BASE + 3,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "voicemail",
+ .gpio = LATCH1_GPIO_BASE + 4,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+ {
+ .name = "voice",
+ .gpio = LATCH1_GPIO_BASE + 5,
+ .default_state = LEDS_GPIO_DEFSTATE_OFF,
+ },
+};
+
+static const struct gpio_led_platform_data leds_pdata __initconst = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
};
static struct i2c_board_info ams_delta_camera_board_info[] = {
@@ -275,13 +446,17 @@
};
static struct platform_device *ams_delta_devices[] __initdata = {
- &ams_delta_nand_device,
+ &latch1_gpio_device,
+ &latch2_gpio_device,
&ams_delta_kp_device,
- &ams_delta_lcd_device,
- &ams_delta_led_device,
&ams_delta_camera_device,
};
+static struct platform_device *late_devices[] __initdata = {
+ &ams_delta_nand_device,
+ &ams_delta_lcd_device,
+};
+
static void __init ams_delta_init(void)
{
/* mux pins for uarts */
@@ -307,15 +482,13 @@
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
- /* Clear latch2 (NAND, LCD, modem enable) */
- ams_delta_latch2_write(~0, 0);
-
omap1_usb_init(&ams_delta_usb_config);
omap1_set_camera_info(&ams_delta_camera_platform_data);
#ifdef CONFIG_LEDS_TRIGGERS
led_trigger_register_simple("ams_delta_camera",
&ams_delta_camera_led_trigger);
#endif
+ gpio_led_register_device(-1, &leds_pdata);
platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
ams_delta_init_fiq();
@@ -323,16 +496,34 @@
omap_writew(omap_readw(ARM_RSTCT1) | 0x0004, ARM_RSTCT1);
}
+static void modem_pm(struct uart_port *port, unsigned int state, unsigned old)
+{
+ struct modem_private_data *priv = port->private_data;
+
+ if (IS_ERR(priv->regulator))
+ return;
+
+ if (state == old)
+ return;
+
+ if (state == 0)
+ regulator_enable(priv->regulator);
+ else if (old == 0)
+ regulator_disable(priv->regulator);
+}
+
static struct plat_serial8250_port ams_delta_modem_ports[] = {
{
- .membase = IOMEM(AMS_DELTA_MODEM_VIRT),
- .mapbase = AMS_DELTA_MODEM_PHYS,
+ .membase = IOMEM(MODEM_VIRT),
+ .mapbase = MODEM_PHYS,
.irq = -EINVAL, /* changed later */
.flags = UPF_BOOT_AUTOCONF,
.irqflags = IRQF_TRIGGER_RISING,
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = BASE_BAUD * 16,
+ .pm = modem_pm,
+ .private_data = &modem_priv,
},
{ },
};
@@ -345,13 +536,27 @@
},
};
-static int __init ams_delta_modem_init(void)
+static int __init late_init(void)
{
int err;
if (!machine_is_ams_delta())
return -ENODEV;
+ err = gpio_request_array(latch_gpios, ARRAY_SIZE(latch_gpios));
+ if (err) {
+ pr_err("Couldn't take over latch1/latch2 GPIO pins\n");
+ return err;
+ }
+
+ platform_add_devices(late_devices, ARRAY_SIZE(late_devices));
+
+ err = platform_device_register(&modem_nreset_device);
+ if (err) {
+ pr_err("Couldn't register the modem regulator device\n");
+ return err;
+ }
+
omap_cfg_reg(M14_1510_GPIO2);
ams_delta_modem_ports[0].irq =
gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
@@ -363,13 +568,35 @@
}
gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
- ams_delta_latch2_write(
- AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
- AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);
+ /* Initialize the modem_nreset regulator consumer before use */
+ modem_priv.regulator = ERR_PTR(-ENODEV);
- return platform_device_register(&ams_delta_modem_device);
+ ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_CODEC,
+ AMS_DELTA_LATCH2_MODEM_CODEC);
+
+ err = platform_device_register(&ams_delta_modem_device);
+ if (err)
+ goto gpio_free;
+
+ /*
+ * Once the modem device is registered, the modem_nreset
+ * regulator can be requested on behalf of that device.
+ */
+ modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
+ "RESET#");
+ if (IS_ERR(modem_priv.regulator)) {
+ err = PTR_ERR(modem_priv.regulator);
+ goto unregister;
+ }
+ return 0;
+
+unregister:
+ platform_device_unregister(&ams_delta_modem_device);
+gpio_free:
+ gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ return err;
}
-arch_initcall(ams_delta_modem_init);
+late_initcall(late_init);
static void __init ams_delta_map_io(void)
{
@@ -388,6 +615,3 @@
.timer = &omap1_timer,
.restart = omap1_restart,
MACHINE_END
-
-EXPORT_SYMBOL(ams_delta_latch1_write);
-EXPORT_SYMBOL(ams_delta_latch2_write);
diff --git a/arch/arm/mach-omap1/include/mach/system.h b/arch/arm/mach-omap1/include/mach/system.h
deleted file mode 100644
index a6c1b3a..0000000
--- a/arch/arm/mach-omap1/include/mach/system.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap1/include/mach/system.h
- */
-
-#include <plat/system.h>
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index 89ea20c..0c2c366 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -42,9 +42,9 @@
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/io.h>
+#include <linux/atomic.h>
#include <asm/irq.h>
-#include <linux/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
@@ -108,13 +108,7 @@
__u32 use_idlect1 = arm_idlect1_mask;
int do_sleep = 0;
- local_irq_disable();
local_fiq_disable();
- if (need_resched()) {
- local_fiq_enable();
- local_irq_enable();
- return;
- }
#if defined(CONFIG_OMAP_MPU_TIMER) && !defined(CONFIG_OMAP_DM_TIMER)
#warning Enable 32kHz OS timer in order to allow sleep states in idle
@@ -157,14 +151,12 @@
omap_writel(saved_idlect1, ARM_IDLECT1);
local_fiq_enable();
- local_irq_enable();
return;
}
omap_sram_suspend(omap_readl(ARM_IDLECT1),
omap_readl(ARM_IDLECT2));
local_fiq_enable();
- local_irq_enable();
}
/*
@@ -583,8 +575,6 @@
#endif /* DEBUG && CONFIG_PROC_FS */
-static void (*saved_idle)(void) = NULL;
-
/*
* omap_pm_prepare - Do preliminary suspend work.
*
@@ -592,8 +582,7 @@
static int omap_pm_prepare(void)
{
/* We cannot sleep in idle until we have resumed */
- saved_idle = pm_idle;
- pm_idle = NULL;
+ disable_hlt();
return 0;
}
@@ -630,7 +619,7 @@
static void omap_pm_finish(void)
{
- pm_idle = saved_idle;
+ enable_hlt();
}
@@ -687,7 +676,7 @@
return -ENODEV;
}
- pm_idle = omap1_pm_idle;
+ arm_pm_idle = omap1_pm_idle;
if (cpu_is_omap7xx())
setup_irq(INT_7XX_WAKE_UP_REQ, &omap_wakeup_irq);
diff --git a/arch/arm/mach-omap2/emu.c b/arch/arm/mach-omap2/emu.c
index 9c442e2..ce91aad 100644
--- a/arch/arm/mach-omap2/emu.c
+++ b/arch/arm/mach-omap2/emu.c
@@ -30,29 +30,8 @@
#define ETB_BASE (L4_EMU_34XX_PHYS + 0x1b000)
#define DAPCTL (L4_EMU_34XX_PHYS + 0x1d000)
-static struct amba_device omap3_etb_device = {
- .dev = {
- .init_name = "etb",
- },
- .res = {
- .start = ETB_BASE,
- .end = ETB_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .periphid = 0x000bb907,
-};
-
-static struct amba_device omap3_etm_device = {
- .dev = {
- .init_name = "etm",
- },
- .res = {
- .start = ETM_BASE,
- .end = ETM_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .periphid = 0x102bb921,
-};
+static AMBA_APB_DEVICE(omap3_etb, "etb", 0x000bb907, ETB_BASE, { }, NULL);
+static AMBA_APB_DEVICE(omap3_etm, "etm", 0x102bb921, ETM_BASE, { }, NULL);
static int __init emu_init(void)
{
@@ -66,4 +45,3 @@
}
subsys_initcall(emu_init);
-
diff --git a/arch/arm/mach-omap2/include/mach/system.h b/arch/arm/mach-omap2/include/mach/system.h
deleted file mode 100644
index d488721..0000000
--- a/arch/arm/mach-omap2/include/mach/system.h
+++ /dev/null
@@ -1,5 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/system.h
- */
-
-#include <plat/system.h>
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index 23de98d..a4eb5c2 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -226,7 +226,6 @@
static void omap2_pm_idle(void)
{
- local_irq_disable();
local_fiq_disable();
if (!omap2_can_sleep()) {
@@ -243,7 +242,6 @@
out:
local_fiq_enable();
- local_irq_enable();
}
#ifdef CONFIG_SUSPEND
@@ -462,7 +460,7 @@
}
suspend_set_ops(&omap_pm_ops);
- pm_idle = omap2_pm_idle;
+ arm_pm_idle = omap2_pm_idle;
return 0;
}
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index fc69875..b77df73 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -418,10 +418,9 @@
static void omap3_pm_idle(void)
{
- local_irq_disable();
local_fiq_disable();
- if (omap_irq_pending() || need_resched())
+ if (omap_irq_pending())
goto out;
trace_power_start(POWER_CSTATE, 1, smp_processor_id());
@@ -434,7 +433,6 @@
out:
local_fiq_enable();
- local_irq_enable();
}
#ifdef CONFIG_SUSPEND
@@ -848,7 +846,7 @@
suspend_set_ops(&omap_pm_ops);
#endif /* CONFIG_SUSPEND */
- pm_idle = omap3_pm_idle;
+ arm_pm_idle = omap3_pm_idle;
omap3_idle_init();
/*
diff --git a/arch/arm/mach-omap2/pm44xx.c b/arch/arm/mach-omap2/pm44xx.c
index c264ef7..c840689 100644
--- a/arch/arm/mach-omap2/pm44xx.c
+++ b/arch/arm/mach-omap2/pm44xx.c
@@ -173,18 +173,16 @@
* omap_default_idle - OMAP4 default ilde routine.'
*
* Implements OMAP4 memory, IO ordering requirements which can't be addressed
- * with default arch_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and
+ * with default cpu_do_idle() hook. Used by all CPUs with !CONFIG_CPUIDLE and
* by secondary CPU with CONFIG_CPUIDLE.
*/
static void omap_default_idle(void)
{
- local_irq_disable();
local_fiq_disable();
omap_do_wfi();
local_fiq_enable();
- local_irq_enable();
}
/**
@@ -255,8 +253,8 @@
suspend_set_ops(&omap_pm_ops);
#endif /* CONFIG_SUSPEND */
- /* Overwrite the default arch_idle() */
- pm_idle = omap_default_idle;
+ /* Overwrite the default cpu_do_idle() */
+ arm_pm_idle = omap_default_idle;
omap4_idle_init();
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 860118a..873b51d 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -24,7 +24,6 @@
#include <linux/interrupt.h>
#include <linux/slab.h>
-#include <mach/system.h>
#include <plat/common.h>
#include <plat/prcm.h>
#include <plat/irqs.h>
diff --git a/arch/arm/mach-orion5x/include/mach/system.h b/arch/arm/mach-orion5x/include/mach/system.h
deleted file mode 100644
index 825a265..0000000
--- a/arch/arm/mach-orion5x/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-orion5x/include/mach/system.h
- *
- * Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-picoxcell/include/mach/system.h b/arch/arm/mach-picoxcell/include/mach/system.h
deleted file mode 100644
index 1a5d8cb..0000000
--- a/arch/arm/mach-picoxcell/include/mach/system.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright (c) 2011 Picochip Ltd., Jamie Iles
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching and wait for interrupt
- * tricks.
- */
- cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-pnx4008/include/mach/system.h b/arch/arm/mach-pnx4008/include/mach/system.h
deleted file mode 100644
index 60cfe71..0000000
--- a/arch/arm/mach-pnx4008/include/mach/system.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/system.h
- *
- * Copyright (C) 2003 Philips Semiconductors
- * Copyright (C) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-prima2/include/mach/system.h b/arch/arm/mach-prima2/include/mach/system.h
deleted file mode 100644
index 2c7d2a9..0000000
--- a/arch/arm/mach-prima2/include/mach/system.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/*
- * arch/arm/mach-prima2/include/mach/system.h
- *
- * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
- *
- * Licensed under GPLv2 or later.
- */
-
-#ifndef __MACH_SYSTEM_H__
-#define __MACH_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 208eef1..f2c23ea 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -245,6 +245,21 @@
ASIC3_GPIOD15_nPIOW,
};
+static struct asic3_led asic3_leds[ASIC3_NUM_LEDS] = {
+ [0] = {
+ .name = "hx4700:amber",
+ .default_trigger = "ds2760-battery.0-charging-blink-full-solid",
+ },
+ [1] = {
+ .name = "hx4700:green",
+ .default_trigger = "unused",
+ },
+ [2] = {
+ .name = "hx4700:blue",
+ .default_trigger = "hx4700-radio",
+ },
+};
+
static struct resource asic3_resources[] = {
/* GPIO part */
[0] = {
@@ -275,6 +290,7 @@
.gpio_config_num = ARRAY_SIZE(asic3_gpio_config),
.irq_base = IRQ_BOARD_START,
.gpio_base = HX4700_ASIC3_GPIO_BASE,
+ .leds = asic3_leds,
};
static struct platform_device asic3 = {
@@ -705,10 +721,9 @@
gpio_set_value(GPIO91_HX4700_FLASH_VPEN, vpp);
}
-static struct resource strataflash_resource = {
- .start = PXA_CS0_PHYS,
- .end = PXA_CS0_PHYS + SZ_128M - 1,
- .flags = IORESOURCE_MEM,
+static struct resource strataflash_resource[] = {
+ [0] = DEFINE_RES_MEM(PXA_CS0_PHYS, SZ_64M),
+ [1] = DEFINE_RES_MEM(PXA_CS0_PHYS + SZ_64M, SZ_64M),
};
static struct physmap_flash_data strataflash_data = {
@@ -719,8 +734,8 @@
static struct platform_device strataflash = {
.name = "physmap-flash",
.id = -1,
- .resource = &strataflash_resource,
- .num_resources = 1,
+ .resource = strataflash_resource,
+ .num_resources = ARRAY_SIZE(strataflash_resource),
.dev = {
.platform_data = &strataflash_data,
},
diff --git a/arch/arm/mach-pxa/include/mach/system.h b/arch/arm/mach-pxa/include/mach/system.h
deleted file mode 100644
index c5afacd..0000000
--- a/arch/arm/mach-pxa/include/mach/system.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * arch/arm/mach-pxa/include/mach/system.h
- *
- * Author: Nicolas Pitre
- * Created: Jun 15, 2001
- * Copyright: MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index 00d6eac..d8de3e5 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -208,6 +208,7 @@
INIT_CLKREG(&clk_pxa25x_gpio11, NULL, "GPIO11_CLK"),
INIT_CLKREG(&clk_pxa25x_gpio12, NULL, "GPIO12_CLK"),
INIT_CLKREG(&clk_pxa25x_mem, "pxa2xx-pcmcia", NULL),
+ INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
};
static struct clk_lookup pxa25x_hwuart_clkreg =
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index c1673b3..a3fabc9 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -229,6 +229,7 @@
INIT_CLKREG(&clk_pxa27x_im, NULL, "IMCLK"),
INIT_CLKREG(&clk_pxa27x_memc, NULL, "MEMCLK"),
INIT_CLKREG(&clk_pxa27x_mem, "pxa2xx-pcmcia", NULL),
+ INIT_CLKREG(&clk_dummy, "pxa-gpio", NULL),
};
#ifdef CONFIG_PM
diff --git a/arch/arm/mach-realview/core.h b/arch/arm/mach-realview/core.h
index 735b57a..f8f2c0a 100644
--- a/arch/arm/mach-realview/core.h
+++ b/arch/arm/mach-realview/core.h
@@ -28,21 +28,11 @@
#include <asm/setup.h>
#include <asm/leds.h>
-#define AMBA_DEVICE(name,busid,base,plat) \
-static struct amba_device name##_device = { \
- .dev = { \
- .coherent_dma_mask = ~0, \
- .init_name = busid, \
- .platform_data = plat, \
- }, \
- .res = { \
- .start = REALVIEW_##base##_BASE, \
- .end = (REALVIEW_##base##_BASE) + SZ_4K - 1, \
- .flags = IORESOURCE_MEM, \
- }, \
- .dma_mask = ~0, \
- .irq = base##_IRQ, \
-}
+#define APB_DEVICE(name, busid, base, plat) \
+static AMBA_APB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
+
+#define AHB_DEVICE(name, busid, base, plat) \
+static AMBA_AHB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
struct machine_desc;
diff --git a/arch/arm/mach-realview/include/mach/irqs-pb1176.h b/arch/arm/mach-realview/include/mach/irqs-pb1176.h
index 5c3c625..708f841 100644
--- a/arch/arm/mach-realview/include/mach/irqs-pb1176.h
+++ b/arch/arm/mach-realview/include/mach/irqs-pb1176.h
@@ -40,6 +40,7 @@
#define IRQ_DC1176_L2CC (IRQ_DC1176_GIC_START + 13)
#define IRQ_DC1176_RTC (IRQ_DC1176_GIC_START + 14)
#define IRQ_DC1176_CLCD (IRQ_DC1176_GIC_START + 15) /* CLCD controller */
+#define IRQ_DC1176_GPIO0 (IRQ_DC1176_GIC_START + 16)
#define IRQ_DC1176_SSP (IRQ_DC1176_GIC_START + 17) /* SSP port */
#define IRQ_DC1176_UART0 (IRQ_DC1176_GIC_START + 18) /* UART 0 on development chip */
#define IRQ_DC1176_UART1 (IRQ_DC1176_GIC_START + 19) /* UART 1 on development chip */
@@ -73,7 +74,6 @@
#define IRQ_PB1176_DMAC (IRQ_PB1176_GIC_START + 24) /* DMA controller */
#define IRQ_PB1176_RTC (IRQ_PB1176_GIC_START + 25) /* Real Time Clock */
-#define IRQ_PB1176_GPIO0 -1
#define IRQ_PB1176_SCTL -1
#define NR_GIC_PB1176 2
diff --git a/arch/arm/mach-realview/include/mach/system.h b/arch/arm/mach-realview/include/mach/system.h
deleted file mode 100644
index 471b671..0000000
--- a/arch/arm/mach-realview/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-realview/include/mach/system.h
- *
- * Copyright (C) 2003 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c
index 9578145..157e1bc6 100644
--- a/arch/arm/mach-realview/realview_eb.c
+++ b/arch/arm/mach-realview/realview_eb.c
@@ -135,63 +135,63 @@
/*
* These devices are connected via the core APB bridge
*/
-#define GPIO2_IRQ { IRQ_EB_GPIO2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_EB_GPIO3, NO_IRQ }
+#define GPIO2_IRQ { IRQ_EB_GPIO2 }
+#define GPIO3_IRQ { IRQ_EB_GPIO3 }
-#define AACI_IRQ { IRQ_EB_AACI, NO_IRQ }
+#define AACI_IRQ { IRQ_EB_AACI }
#define MMCI0_IRQ { IRQ_EB_MMCI0A, IRQ_EB_MMCI0B }
-#define KMI0_IRQ { IRQ_EB_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_EB_KMI1, NO_IRQ }
+#define KMI0_IRQ { IRQ_EB_KMI0 }
+#define KMI1_IRQ { IRQ_EB_KMI1 }
/*
* These devices are connected directly to the multi-layer AHB switch
*/
-#define EB_SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define EB_CLCD_IRQ { IRQ_EB_CLCD, NO_IRQ }
-#define DMAC_IRQ { IRQ_EB_DMA, NO_IRQ }
+#define EB_SMC_IRQ { }
+#define MPMC_IRQ { }
+#define EB_CLCD_IRQ { IRQ_EB_CLCD }
+#define DMAC_IRQ { IRQ_EB_DMA }
/*
* These devices are connected via the core APB bridge
*/
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define EB_WATCHDOG_IRQ { IRQ_EB_WDOG, NO_IRQ }
-#define EB_GPIO0_IRQ { IRQ_EB_GPIO0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_EB_GPIO1, NO_IRQ }
-#define EB_RTC_IRQ { IRQ_EB_RTC, NO_IRQ }
+#define SCTL_IRQ { }
+#define EB_WATCHDOG_IRQ { IRQ_EB_WDOG }
+#define EB_GPIO0_IRQ { IRQ_EB_GPIO0 }
+#define GPIO1_IRQ { IRQ_EB_GPIO1 }
+#define EB_RTC_IRQ { IRQ_EB_RTC }
/*
* These devices are connected via the DMA APB bridge
*/
-#define SCI_IRQ { IRQ_EB_SCI, NO_IRQ }
-#define EB_UART0_IRQ { IRQ_EB_UART0, NO_IRQ }
-#define EB_UART1_IRQ { IRQ_EB_UART1, NO_IRQ }
-#define EB_UART2_IRQ { IRQ_EB_UART2, NO_IRQ }
-#define EB_UART3_IRQ { IRQ_EB_UART3, NO_IRQ }
-#define EB_SSP_IRQ { IRQ_EB_SSP, NO_IRQ }
+#define SCI_IRQ { IRQ_EB_SCI }
+#define EB_UART0_IRQ { IRQ_EB_UART0 }
+#define EB_UART1_IRQ { IRQ_EB_UART1 }
+#define EB_UART2_IRQ { IRQ_EB_UART2 }
+#define EB_UART3_IRQ { IRQ_EB_UART3 }
+#define EB_SSP_IRQ { IRQ_EB_SSP }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
+APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+APB_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:smc", EB_SMC, NULL);
-AMBA_DEVICE(clcd, "dev:clcd", EB_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "dev:dmac", DMAC, NULL);
-AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:wdog", EB_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:rtc", EB_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:ssp0", EB_SSP, &ssp0_plat_data);
+AHB_DEVICE(smc, "dev:smc", EB_SMC, NULL);
+AHB_DEVICE(clcd, "dev:clcd", EB_CLCD, &clcd_plat_data);
+AHB_DEVICE(dmac, "dev:dmac", DMAC, NULL);
+AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+APB_DEVICE(wdog, "dev:wdog", EB_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+APB_DEVICE(rtc, "dev:rtc", EB_RTC, NULL);
+APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
+APB_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
+APB_DEVICE(ssp0, "dev:ssp0", EB_SSP, &ssp0_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c
index e4abe94..b1d7caf 100644
--- a/arch/arm/mach-realview/realview_pb1176.c
+++ b/arch/arm/mach-realview/realview_pb1176.c
@@ -132,50 +132,50 @@
/*
* RealView PB1176 AMBA devices
*/
-#define GPIO2_IRQ { IRQ_PB1176_GPIO2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_PB1176_GPIO3, NO_IRQ }
-#define AACI_IRQ { IRQ_PB1176_AACI, NO_IRQ }
+#define GPIO2_IRQ { IRQ_PB1176_GPIO2 }
+#define GPIO3_IRQ { IRQ_PB1176_GPIO3 }
+#define AACI_IRQ { IRQ_PB1176_AACI }
#define MMCI0_IRQ { IRQ_PB1176_MMCI0A, IRQ_PB1176_MMCI0B }
-#define KMI0_IRQ { IRQ_PB1176_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_PB1176_KMI1, NO_IRQ }
-#define PB1176_SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define PB1176_CLCD_IRQ { IRQ_DC1176_CLCD, NO_IRQ }
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define PB1176_WATCHDOG_IRQ { IRQ_DC1176_WATCHDOG, NO_IRQ }
-#define PB1176_GPIO0_IRQ { IRQ_PB1176_GPIO0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_PB1176_GPIO1, NO_IRQ }
-#define PB1176_RTC_IRQ { IRQ_DC1176_RTC, NO_IRQ }
-#define SCI_IRQ { IRQ_PB1176_SCI, NO_IRQ }
-#define PB1176_UART0_IRQ { IRQ_DC1176_UART0, NO_IRQ }
-#define PB1176_UART1_IRQ { IRQ_DC1176_UART1, NO_IRQ }
-#define PB1176_UART2_IRQ { IRQ_DC1176_UART2, NO_IRQ }
-#define PB1176_UART3_IRQ { IRQ_DC1176_UART3, NO_IRQ }
-#define PB1176_UART4_IRQ { IRQ_PB1176_UART4, NO_IRQ }
-#define PB1176_SSP_IRQ { IRQ_DC1176_SSP, NO_IRQ }
+#define KMI0_IRQ { IRQ_PB1176_KMI0 }
+#define KMI1_IRQ { IRQ_PB1176_KMI1 }
+#define PB1176_SMC_IRQ { }
+#define MPMC_IRQ { }
+#define PB1176_CLCD_IRQ { IRQ_DC1176_CLCD }
+#define SCTL_IRQ { }
+#define PB1176_WATCHDOG_IRQ { IRQ_DC1176_WATCHDOG }
+#define PB1176_GPIO0_IRQ { IRQ_DC1176_GPIO0 }
+#define GPIO1_IRQ { IRQ_PB1176_GPIO1 }
+#define PB1176_RTC_IRQ { IRQ_DC1176_RTC }
+#define SCI_IRQ { IRQ_PB1176_SCI }
+#define PB1176_UART0_IRQ { IRQ_DC1176_UART0 }
+#define PB1176_UART1_IRQ { IRQ_DC1176_UART1 }
+#define PB1176_UART2_IRQ { IRQ_DC1176_UART2 }
+#define PB1176_UART3_IRQ { IRQ_DC1176_UART3 }
+#define PB1176_UART4_IRQ { IRQ_PB1176_UART4 }
+#define PB1176_SSP_IRQ { IRQ_DC1176_SSP }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
-AMBA_DEVICE(uart4, "fpga:uart4", PB1176_UART4, NULL);
+APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+APB_DEVICE(uart4, "fpga:uart4", PB1176_UART4, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:smc", PB1176_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:wdog", PB1176_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", PB1176_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:rtc", PB1176_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:uart0", PB1176_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", PB1176_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", PB1176_UART2, NULL);
-AMBA_DEVICE(uart3, "dev:uart3", PB1176_UART3, NULL);
-AMBA_DEVICE(ssp0, "dev:ssp0", PB1176_SSP, &ssp0_plat_data);
-AMBA_DEVICE(clcd, "dev:clcd", PB1176_CLCD, &clcd_plat_data);
+AHB_DEVICE(smc, "dev:smc", PB1176_SMC, NULL);
+AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+APB_DEVICE(wdog, "dev:wdog", PB1176_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", PB1176_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+APB_DEVICE(rtc, "dev:rtc", PB1176_RTC, NULL);
+APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
+APB_DEVICE(uart0, "dev:uart0", PB1176_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", PB1176_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", PB1176_UART2, NULL);
+APB_DEVICE(uart3, "dev:uart3", PB1176_UART3, NULL);
+APB_DEVICE(ssp0, "dev:ssp0", PB1176_SSP, &ssp0_plat_data);
+AHB_DEVICE(clcd, "dev:clcd", PB1176_CLCD, &clcd_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&uart0_device,
diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c
index 2147335..ae7fe54 100644
--- a/arch/arm/mach-realview/realview_pb11mp.c
+++ b/arch/arm/mach-realview/realview_pb11mp.c
@@ -127,52 +127,52 @@
* RealView PB11MPCore AMBA devices
*/
-#define GPIO2_IRQ { IRQ_PB11MP_GPIO2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_PB11MP_GPIO3, NO_IRQ }
-#define AACI_IRQ { IRQ_TC11MP_AACI, NO_IRQ }
+#define GPIO2_IRQ { IRQ_PB11MP_GPIO2 }
+#define GPIO3_IRQ { IRQ_PB11MP_GPIO3 }
+#define AACI_IRQ { IRQ_TC11MP_AACI }
#define MMCI0_IRQ { IRQ_TC11MP_MMCI0A, IRQ_TC11MP_MMCI0B }
-#define KMI0_IRQ { IRQ_TC11MP_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_TC11MP_KMI1, NO_IRQ }
-#define PB11MP_SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define PB11MP_CLCD_IRQ { IRQ_PB11MP_CLCD, NO_IRQ }
-#define DMAC_IRQ { IRQ_PB11MP_DMAC, NO_IRQ }
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define PB11MP_WATCHDOG_IRQ { IRQ_PB11MP_WATCHDOG, NO_IRQ }
-#define PB11MP_GPIO0_IRQ { IRQ_PB11MP_GPIO0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_PB11MP_GPIO1, NO_IRQ }
-#define PB11MP_RTC_IRQ { IRQ_TC11MP_RTC, NO_IRQ }
-#define SCI_IRQ { IRQ_PB11MP_SCI, NO_IRQ }
-#define PB11MP_UART0_IRQ { IRQ_TC11MP_UART0, NO_IRQ }
-#define PB11MP_UART1_IRQ { IRQ_TC11MP_UART1, NO_IRQ }
-#define PB11MP_UART2_IRQ { IRQ_PB11MP_UART2, NO_IRQ }
-#define PB11MP_UART3_IRQ { IRQ_PB11MP_UART3, NO_IRQ }
-#define PB11MP_SSP_IRQ { IRQ_PB11MP_SSP, NO_IRQ }
+#define KMI0_IRQ { IRQ_TC11MP_KMI0 }
+#define KMI1_IRQ { IRQ_TC11MP_KMI1 }
+#define PB11MP_SMC_IRQ { }
+#define MPMC_IRQ { }
+#define PB11MP_CLCD_IRQ { IRQ_PB11MP_CLCD }
+#define DMAC_IRQ { IRQ_PB11MP_DMAC }
+#define SCTL_IRQ { }
+#define PB11MP_WATCHDOG_IRQ { IRQ_PB11MP_WATCHDOG }
+#define PB11MP_GPIO0_IRQ { IRQ_PB11MP_GPIO0 }
+#define GPIO1_IRQ { IRQ_PB11MP_GPIO1 }
+#define PB11MP_RTC_IRQ { IRQ_TC11MP_RTC }
+#define SCI_IRQ { IRQ_PB11MP_SCI }
+#define PB11MP_UART0_IRQ { IRQ_TC11MP_UART0 }
+#define PB11MP_UART1_IRQ { IRQ_TC11MP_UART1 }
+#define PB11MP_UART2_IRQ { IRQ_PB11MP_UART2 }
+#define PB11MP_UART3_IRQ { IRQ_PB11MP_UART3 }
+#define PB11MP_SSP_IRQ { IRQ_PB11MP_SSP }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:uart3", PB11MP_UART3, NULL);
+APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+APB_DEVICE(uart3, "fpga:uart3", PB11MP_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:smc", PB11MP_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:wdog", PB11MP_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", PB11MP_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:rtc", PB11MP_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:uart0", PB11MP_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", PB11MP_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", PB11MP_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:ssp0", PB11MP_SSP, &ssp0_plat_data);
+AHB_DEVICE(smc, "dev:smc", PB11MP_SMC, NULL);
+AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+APB_DEVICE(wdog, "dev:wdog", PB11MP_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", PB11MP_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+APB_DEVICE(rtc, "dev:rtc", PB11MP_RTC, NULL);
+APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
+APB_DEVICE(uart0, "dev:uart0", PB11MP_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", PB11MP_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", PB11MP_UART2, NULL);
+APB_DEVICE(ssp0, "dev:ssp0", PB11MP_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:clcd", PB11MP_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
+AHB_DEVICE(clcd, "issp:clcd", PB11MP_CLCD, &clcd_plat_data);
+AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c
index 25b2e59..5965017 100644
--- a/arch/arm/mach-realview/realview_pba8.c
+++ b/arch/arm/mach-realview/realview_pba8.c
@@ -122,52 +122,52 @@
* RealView PBA8Core AMBA devices
*/
-#define GPIO2_IRQ { IRQ_PBA8_GPIO2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_PBA8_GPIO3, NO_IRQ }
-#define AACI_IRQ { IRQ_PBA8_AACI, NO_IRQ }
+#define GPIO2_IRQ { IRQ_PBA8_GPIO2 }
+#define GPIO3_IRQ { IRQ_PBA8_GPIO3 }
+#define AACI_IRQ { IRQ_PBA8_AACI }
#define MMCI0_IRQ { IRQ_PBA8_MMCI0A, IRQ_PBA8_MMCI0B }
-#define KMI0_IRQ { IRQ_PBA8_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_PBA8_KMI1, NO_IRQ }
-#define PBA8_SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define PBA8_CLCD_IRQ { IRQ_PBA8_CLCD, NO_IRQ }
-#define DMAC_IRQ { IRQ_PBA8_DMAC, NO_IRQ }
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define PBA8_WATCHDOG_IRQ { IRQ_PBA8_WATCHDOG, NO_IRQ }
-#define PBA8_GPIO0_IRQ { IRQ_PBA8_GPIO0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_PBA8_GPIO1, NO_IRQ }
-#define PBA8_RTC_IRQ { IRQ_PBA8_RTC, NO_IRQ }
-#define SCI_IRQ { IRQ_PBA8_SCI, NO_IRQ }
-#define PBA8_UART0_IRQ { IRQ_PBA8_UART0, NO_IRQ }
-#define PBA8_UART1_IRQ { IRQ_PBA8_UART1, NO_IRQ }
-#define PBA8_UART2_IRQ { IRQ_PBA8_UART2, NO_IRQ }
-#define PBA8_UART3_IRQ { IRQ_PBA8_UART3, NO_IRQ }
-#define PBA8_SSP_IRQ { IRQ_PBA8_SSP, NO_IRQ }
+#define KMI0_IRQ { IRQ_PBA8_KMI0 }
+#define KMI1_IRQ { IRQ_PBA8_KMI1 }
+#define PBA8_SMC_IRQ { }
+#define MPMC_IRQ { }
+#define PBA8_CLCD_IRQ { IRQ_PBA8_CLCD }
+#define DMAC_IRQ { IRQ_PBA8_DMAC }
+#define SCTL_IRQ { }
+#define PBA8_WATCHDOG_IRQ { IRQ_PBA8_WATCHDOG }
+#define PBA8_GPIO0_IRQ { IRQ_PBA8_GPIO0 }
+#define GPIO1_IRQ { IRQ_PBA8_GPIO1 }
+#define PBA8_RTC_IRQ { IRQ_PBA8_RTC }
+#define SCI_IRQ { IRQ_PBA8_SCI }
+#define PBA8_UART0_IRQ { IRQ_PBA8_UART0 }
+#define PBA8_UART1_IRQ { IRQ_PBA8_UART1 }
+#define PBA8_UART2_IRQ { IRQ_PBA8_UART2 }
+#define PBA8_UART3_IRQ { IRQ_PBA8_UART3 }
+#define PBA8_SSP_IRQ { IRQ_PBA8_SSP }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:uart3", PBA8_UART3, NULL);
+APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+APB_DEVICE(uart3, "fpga:uart3", PBA8_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:smc", PBA8_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:wdog", PBA8_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", PBA8_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:rtc", PBA8_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:uart0", PBA8_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", PBA8_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", PBA8_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:ssp0", PBA8_SSP, &ssp0_plat_data);
+AHB_DEVICE(smc, "dev:smc", PBA8_SMC, NULL);
+AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+APB_DEVICE(wdog, "dev:wdog", PBA8_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", PBA8_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+APB_DEVICE(rtc, "dev:rtc", PBA8_RTC, NULL);
+APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
+APB_DEVICE(uart0, "dev:uart0", PBA8_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", PBA8_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", PBA8_UART2, NULL);
+APB_DEVICE(ssp0, "dev:ssp0", PBA8_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:clcd", PBA8_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
+AHB_DEVICE(clcd, "issp:clcd", PBA8_CLCD, &clcd_plat_data);
+AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c
index ac71564..1cd9956 100644
--- a/arch/arm/mach-realview/realview_pbx.c
+++ b/arch/arm/mach-realview/realview_pbx.c
@@ -144,52 +144,52 @@
* RealView PBXCore AMBA devices
*/
-#define GPIO2_IRQ { IRQ_PBX_GPIO2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_PBX_GPIO3, NO_IRQ }
-#define AACI_IRQ { IRQ_PBX_AACI, NO_IRQ }
+#define GPIO2_IRQ { IRQ_PBX_GPIO2 }
+#define GPIO3_IRQ { IRQ_PBX_GPIO3 }
+#define AACI_IRQ { IRQ_PBX_AACI }
#define MMCI0_IRQ { IRQ_PBX_MMCI0A, IRQ_PBX_MMCI0B }
-#define KMI0_IRQ { IRQ_PBX_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_PBX_KMI1, NO_IRQ }
-#define PBX_SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define PBX_CLCD_IRQ { IRQ_PBX_CLCD, NO_IRQ }
-#define DMAC_IRQ { IRQ_PBX_DMAC, NO_IRQ }
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define PBX_WATCHDOG_IRQ { IRQ_PBX_WATCHDOG, NO_IRQ }
-#define PBX_GPIO0_IRQ { IRQ_PBX_GPIO0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_PBX_GPIO1, NO_IRQ }
-#define PBX_RTC_IRQ { IRQ_PBX_RTC, NO_IRQ }
-#define SCI_IRQ { IRQ_PBX_SCI, NO_IRQ }
-#define PBX_UART0_IRQ { IRQ_PBX_UART0, NO_IRQ }
-#define PBX_UART1_IRQ { IRQ_PBX_UART1, NO_IRQ }
-#define PBX_UART2_IRQ { IRQ_PBX_UART2, NO_IRQ }
-#define PBX_UART3_IRQ { IRQ_PBX_UART3, NO_IRQ }
-#define PBX_SSP_IRQ { IRQ_PBX_SSP, NO_IRQ }
+#define KMI0_IRQ { IRQ_PBX_KMI0 }
+#define KMI1_IRQ { IRQ_PBX_KMI1 }
+#define PBX_SMC_IRQ { }
+#define MPMC_IRQ { }
+#define PBX_CLCD_IRQ { IRQ_PBX_CLCD }
+#define DMAC_IRQ { IRQ_PBX_DMAC }
+#define SCTL_IRQ { }
+#define PBX_WATCHDOG_IRQ { IRQ_PBX_WATCHDOG }
+#define PBX_GPIO0_IRQ { IRQ_PBX_GPIO0 }
+#define GPIO1_IRQ { IRQ_PBX_GPIO1 }
+#define PBX_RTC_IRQ { IRQ_PBX_RTC }
+#define SCI_IRQ { IRQ_PBX_SCI }
+#define PBX_UART0_IRQ { IRQ_PBX_UART0 }
+#define PBX_UART1_IRQ { IRQ_PBX_UART1 }
+#define PBX_UART2_IRQ { IRQ_PBX_UART2 }
+#define PBX_UART3_IRQ { IRQ_PBX_UART3 }
+#define PBX_SSP_IRQ { IRQ_PBX_SSP }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:uart3", PBX_UART3, NULL);
+APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+APB_DEVICE(uart3, "fpga:uart3", PBX_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:smc", PBX_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:wdog", PBX_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:gpio0", PBX_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:rtc", PBX_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:uart0", PBX_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:uart1", PBX_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:uart2", PBX_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:ssp0", PBX_SSP, &ssp0_plat_data);
+AHB_DEVICE(smc, "dev:smc", PBX_SMC, NULL);
+AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+APB_DEVICE(wdog, "dev:wdog", PBX_WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:gpio0", PBX_GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+APB_DEVICE(rtc, "dev:rtc", PBX_RTC, NULL);
+APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
+APB_DEVICE(uart0, "dev:uart0", PBX_UART0, NULL);
+APB_DEVICE(uart1, "dev:uart1", PBX_UART1, NULL);
+APB_DEVICE(uart2, "dev:uart2", PBX_UART2, NULL);
+APB_DEVICE(ssp0, "dev:ssp0", PBX_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:clcd", PBX_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
+AHB_DEVICE(clcd, "issp:clcd", PBX_CLCD, &clcd_plat_data);
+AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
diff --git a/arch/arm/mach-rpc/include/mach/system.h b/arch/arm/mach-rpc/include/mach/system.h
deleted file mode 100644
index 359bab9..0000000
--- a/arch/arm/mach-rpc/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-rpc/include/mach/system.h
- *
- * Copyright (C) 1996-1999 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-s3c2410/include/mach/system.h b/arch/arm/mach-s3c2410/include/mach/system.h
deleted file mode 100644
index 5e215c1..0000000
--- a/arch/arm/mach-s3c2410/include/mach/system.h
+++ /dev/null
@@ -1,54 +0,0 @@
-/* arch/arm/mach-s3c2410/include/mach/system.h
- *
- * Copyright (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - System function defines and includes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/io.h>
-#include <mach/hardware.h>
-
-#include <mach/map.h>
-#include <mach/idle.h>
-
-#include <mach/regs-clock.h>
-
-void (*s3c24xx_idle)(void);
-
-void s3c24xx_default_idle(void)
-{
- unsigned long tmp;
- int i;
-
- /* idle the system by using the idle mode which will wait for an
- * interrupt to happen before restarting the system.
- */
-
- /* Warning: going into idle state upsets jtag scanning */
-
- __raw_writel(__raw_readl(S3C2410_CLKCON) | S3C2410_CLKCON_IDLE,
- S3C2410_CLKCON);
-
- /* the samsung port seems to do a loop and then unset idle.. */
- for (i = 0; i < 50; i++) {
- tmp += __raw_readl(S3C2410_CLKCON); /* ensure loop not optimised out */
- }
-
- /* this bit is not cleared on re-start... */
-
- __raw_writel(__raw_readl(S3C2410_CLKCON) & ~S3C2410_CLKCON_IDLE,
- S3C2410_CLKCON);
-}
-
-static void arch_idle(void)
-{
- if (s3c24xx_idle != NULL)
- (s3c24xx_idle)();
- else
- s3c24xx_default_idle();
-}
diff --git a/arch/arm/mach-s3c2412/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c
index aff6e85..c6eac98 100644
--- a/arch/arm/mach-s3c2412/s3c2412.c
+++ b/arch/arm/mach-s3c2412/s3c2412.c
@@ -32,8 +32,6 @@
#include <asm/proc-fns.h>
#include <asm/irq.h>
-#include <mach/idle.h>
-
#include <plat/cpu-freq.h>
#include <mach/regs-clock.h>
@@ -164,7 +162,7 @@
/* set our idle function */
- s3c24xx_idle = s3c2412_idle;
+ arm_pm_idle = s3c2412_idle;
/* register our io-tables */
diff --git a/arch/arm/mach-s3c2416/s3c2416.c b/arch/arm/mach-s3c2416/s3c2416.c
index 5287d28..08bb035 100644
--- a/arch/arm/mach-s3c2416/s3c2416.c
+++ b/arch/arm/mach-s3c2416/s3c2416.c
@@ -44,7 +44,6 @@
#include <asm/proc-fns.h>
#include <asm/irq.h>
-#include <mach/idle.h>
#include <mach/regs-s3c2443-clock.h>
#include <plat/gpio-core.h>
@@ -88,8 +87,6 @@
{
printk(KERN_INFO "S3C2416: Initializing architecture\n");
- /* s3c24xx_idle = s3c2416_idle; */
-
/* change WDT IRQ number */
s3c_device_wdt.resource[1].start = IRQ_S3C2443_WDT;
s3c_device_wdt.resource[1].end = IRQ_S3C2443_WDT;
diff --git a/arch/arm/mach-s3c64xx/include/mach/system.h b/arch/arm/mach-s3c64xx/include/mach/system.h
deleted file mode 100644
index 353ed43..0000000
--- a/arch/arm/mach-s3c64xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* linux/arch/arm/mach-s3c6400/include/mach/system.h
- *
- * Copyright 2008 Openmoko, Inc.
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C6400 - system implementation
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
- /* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s5p64x0/common.c b/arch/arm/mach-s5p64x0/common.c
index 52b89a3..9143f8b 100644
--- a/arch/arm/mach-s5p64x0/common.c
+++ b/arch/arm/mach-s5p64x0/common.c
@@ -146,15 +146,12 @@
{
unsigned long val;
- if (!need_resched()) {
- val = __raw_readl(S5P64X0_PWR_CFG);
- val &= ~(0x3 << 5);
- val |= (0x1 << 5);
- __raw_writel(val, S5P64X0_PWR_CFG);
+ val = __raw_readl(S5P64X0_PWR_CFG);
+ val &= ~(0x3 << 5);
+ val |= (0x1 << 5);
+ __raw_writel(val, S5P64X0_PWR_CFG);
- cpu_do_idle();
- }
- local_irq_enable();
+ cpu_do_idle();
}
/*
@@ -286,7 +283,7 @@
printk(KERN_INFO "S5P64X0(S5P6440/S5P6450): Initializing architecture\n");
/* set idle function */
- pm_idle = s5p64x0_idle;
+ arm_pm_idle = s5p64x0_idle;
return device_register(&s5p64x0_dev);
}
diff --git a/arch/arm/mach-s5p64x0/dma.c b/arch/arm/mach-s5p64x0/dma.c
index f820c07..f7f68ad 100644
--- a/arch/arm/mach-s5p64x0/dma.c
+++ b/arch/arm/mach-s5p64x0/dma.c
@@ -108,34 +108,22 @@
.peri_id = s5p6450_pdma_peri,
};
-struct amba_device s5p64x0_device_pdma = {
- .dev = {
- .init_name = "dma-pl330",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .res = {
- .start = S5P64X0_PA_PDMA,
- .end = S5P64X0_PA_PDMA + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_DMA0, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5p64x0_pdma, "dma-pl330", 0x00041330, S5P64X0_PA_PDMA,
+ {IRQ_DMA0}, NULL);
static int __init s5p64x0_dma_init(void)
{
if (soc_is_s5p6450()) {
dma_cap_set(DMA_SLAVE, s5p6450_pdma_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5p6450_pdma_pdata.cap_mask);
- s5p64x0_device_pdma.dev.platform_data = &s5p6450_pdma_pdata;
+ s5p64x0_pdma_device.dev.platform_data = &s5p6450_pdma_pdata;
} else {
dma_cap_set(DMA_SLAVE, s5p6440_pdma_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5p6440_pdma_pdata.cap_mask);
- s5p64x0_device_pdma.dev.platform_data = &s5p6440_pdma_pdata;
+ s5p64x0_pdma_device.dev.platform_data = &s5p6440_pdma_pdata;
}
- amba_device_register(&s5p64x0_device_pdma, &iomem_resource);
+ amba_device_register(&s5p64x0_pdma_device, &iomem_resource);
return 0;
}
diff --git a/arch/arm/mach-s5p64x0/include/mach/system.h b/arch/arm/mach-s5p64x0/include/mach/system.h
deleted file mode 100644
index cf26e09..0000000
--- a/arch/arm/mach-s5p64x0/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* linux/arch/arm/mach-s5p64x0/include/mach/system.h
- *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com
- *
- * S5P64X0 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
- /* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-s5pc100/common.c b/arch/arm/mach-s5pc100/common.c
index c909573..ff71e2d 100644
--- a/arch/arm/mach-s5pc100/common.c
+++ b/arch/arm/mach-s5pc100/common.c
@@ -129,14 +129,6 @@
}
};
-static void s5pc100_idle(void)
-{
- if (!need_resched())
- cpu_do_idle();
-
- local_irq_enable();
-}
-
/*
* s5pc100_map_io
*
@@ -210,10 +202,6 @@
int __init s5pc100_init(void)
{
printk(KERN_INFO "S5PC100: Initializing architecture\n");
-
- /* set idle function */
- pm_idle = s5pc100_idle;
-
return device_register(&s5pc100_dev);
}
diff --git a/arch/arm/mach-s5pc100/dma.c b/arch/arm/mach-s5pc100/dma.c
index c841f4d3..96b1ab3 100644
--- a/arch/arm/mach-s5pc100/dma.c
+++ b/arch/arm/mach-s5pc100/dma.c
@@ -73,21 +73,8 @@
.peri_id = pdma0_peri,
};
-struct amba_device s5pc100_device_pdma0 = {
- .dev = {
- .init_name = "dma-pl330.0",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pc100_pdma0_pdata,
- },
- .res = {
- .start = S5PC100_PA_PDMA0,
- .end = S5PC100_PA_PDMA0 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA0, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pc100_pdma0, "dma-pl330.0", 0x00041330, S5PC100_PA_PDMA0,
+ {IRQ_PDMA0}, &s5pc100_pdma0_pdata);
u8 pdma1_peri[] = {
DMACH_UART0_RX,
@@ -127,31 +114,18 @@
.peri_id = pdma1_peri,
};
-struct amba_device s5pc100_device_pdma1 = {
- .dev = {
- .init_name = "dma-pl330.1",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pc100_pdma1_pdata,
- },
- .res = {
- .start = S5PC100_PA_PDMA1,
- .end = S5PC100_PA_PDMA1 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA1, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pc100_pdma1, "dma-pl330.1", 0x00041330, S5PC100_PA_PDMA1,
+ {IRQ_PDMA1}, &s5pc100_pdma1_pdata);
static int __init s5pc100_dma_init(void)
{
dma_cap_set(DMA_SLAVE, s5pc100_pdma0_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5pc100_pdma0_pdata.cap_mask);
- amba_device_register(&s5pc100_device_pdma0, &iomem_resource);
+ amba_device_register(&s5pc100_pdma0_device, &iomem_resource);
dma_cap_set(DMA_SLAVE, s5pc100_pdma1_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5pc100_pdma1_pdata.cap_mask);
- amba_device_register(&s5pc100_device_pdma1, &iomem_resource);
+ amba_device_register(&s5pc100_pdma1_device, &iomem_resource);
return 0;
}
diff --git a/arch/arm/mach-s5pc100/include/mach/system.h b/arch/arm/mach-s5pc100/include/mach/system.h
deleted file mode 100644
index afc96c2..0000000
--- a/arch/arm/mach-s5pc100/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/* linux/arch/arm/mach-s5pc100/include/mach/system.h
- *
- * Copyright 2009 Samsung Electronics Co.
- * Byungho Min <bhmin@samsung.com>
- *
- * S5PC100 - system implementation
- *
- * Based on mach-s3c6400/include/mach/system.h
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
- /* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_IRQ_H */
diff --git a/arch/arm/mach-s5pv210/common.c b/arch/arm/mach-s5pv210/common.c
index 9c1bcdc..4c9e902 100644
--- a/arch/arm/mach-s5pv210/common.c
+++ b/arch/arm/mach-s5pv210/common.c
@@ -142,14 +142,6 @@
}
};
-static void s5pv210_idle(void)
-{
- if (!need_resched())
- cpu_do_idle();
-
- local_irq_enable();
-}
-
void s5pv210_restart(char mode, const char *cmd)
{
__raw_writel(0x1, S5P_SWRESET);
@@ -247,10 +239,6 @@
int __init s5pv210_init(void)
{
printk(KERN_INFO "S5PV210: Initializing architecture\n");
-
- /* set idle function */
- pm_idle = s5pv210_idle;
-
return device_register(&s5pv210_dev);
}
diff --git a/arch/arm/mach-s5pv210/dma.c b/arch/arm/mach-s5pv210/dma.c
index a6113e0..f6885d2 100644
--- a/arch/arm/mach-s5pv210/dma.c
+++ b/arch/arm/mach-s5pv210/dma.c
@@ -71,21 +71,8 @@
.peri_id = pdma0_peri,
};
-struct amba_device s5pv210_device_pdma0 = {
- .dev = {
- .init_name = "dma-pl330.0",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pv210_pdma0_pdata,
- },
- .res = {
- .start = S5PV210_PA_PDMA0,
- .end = S5PV210_PA_PDMA0 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA0, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pv210_pdma0, "dma-pl330.0", 0x00041330, S5PV210_PA_PDMA0,
+ {IRQ_PDMA0}, &s5pv210_pdma0_pdata);
u8 pdma1_peri[] = {
DMACH_UART0_RX,
@@ -127,31 +114,18 @@
.peri_id = pdma1_peri,
};
-struct amba_device s5pv210_device_pdma1 = {
- .dev = {
- .init_name = "dma-pl330.1",
- .dma_mask = &dma_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &s5pv210_pdma1_pdata,
- },
- .res = {
- .start = S5PV210_PA_PDMA1,
- .end = S5PV210_PA_PDMA1 + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_PDMA1, NO_IRQ},
- .periphid = 0x00041330,
-};
+AMBA_AHB_DEVICE(s5pv210_pdma1, "dma-pl330.1", 0x00041330, S5PV210_PA_PDMA1,
+ {IRQ_PDMA1}, &s5pv210_pdma1_pdata);
static int __init s5pv210_dma_init(void)
{
dma_cap_set(DMA_SLAVE, s5pv210_pdma0_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5pv210_pdma0_pdata.cap_mask);
- amba_device_register(&s5pv210_device_pdma0, &iomem_resource);
+ amba_device_register(&s5pv210_pdma0_device, &iomem_resource);
dma_cap_set(DMA_SLAVE, s5pv210_pdma1_pdata.cap_mask);
dma_cap_set(DMA_CYCLIC, s5pv210_pdma1_pdata.cap_mask);
- amba_device_register(&s5pv210_device_pdma1, &iomem_resource);
+ amba_device_register(&s5pv210_pdma1_device, &iomem_resource);
return 0;
}
diff --git a/arch/arm/mach-s5pv210/include/mach/system.h b/arch/arm/mach-s5pv210/include/mach/system.h
deleted file mode 100644
index bf288ce..0000000
--- a/arch/arm/mach-s5pv210/include/mach/system.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* linux/arch/arm/mach-s5pv210/include/mach/system.h
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- * http://www.samsung.com/
- *
- * S5PV210 - system support header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H __FILE__
-
-static void arch_idle(void)
-{
- /* nothing here yet */
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
diff --git a/arch/arm/mach-sa1100/include/mach/system.h b/arch/arm/mach-sa1100/include/mach/system.h
deleted file mode 100644
index e17b208..0000000
--- a/arch/arm/mach-sa1100/include/mach/system.h
+++ /dev/null
@@ -1,9 +0,0 @@
-/*
- * arch/arm/mach-sa1100/include/mach/system.h
- *
- * Copyright (c) 1999 Nicolas Pitre <nico@fluxnic.net>
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-shark/core.c b/arch/arm/mach-shark/core.c
index a851c25..6a2a7f2 100644
--- a/arch/arm/mach-shark/core.c
+++ b/arch/arm/mach-shark/core.c
@@ -149,10 +149,16 @@
.init = shark_timer_init,
};
+static void shark_init_early(void)
+{
+ disable_hlt();
+}
+
MACHINE_START(SHARK, "Shark")
/* Maintainer: Alexander Schulz */
.atag_offset = 0x3000,
.map_io = shark_map_io,
+ .init_early = shark_init_early,
.init_irq = shark_init_irq,
.timer = &shark_timer,
.dma_zone_size = SZ_4M,
diff --git a/arch/arm/mach-shark/include/mach/system.h b/arch/arm/mach-shark/include/mach/system.h
deleted file mode 100644
index 1b2f2c5..0000000
--- a/arch/arm/mach-shark/include/mach/system.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * arch/arm/mach-shark/include/mach/system.h
- *
- * by Alexander Schulz
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-}
-
-#endif
diff --git a/arch/arm/mach-shmobile/include/mach/system.h b/arch/arm/mach-shmobile/include/mach/system.h
index 956ac18..3bbcb3f 100644
--- a/arch/arm/mach-shmobile/include/mach/system.h
+++ b/arch/arm/mach-shmobile/include/mach/system.h
@@ -1,11 +1,6 @@
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
static inline void arch_reset(char mode, const char *cmd)
{
soft_restart(0);
diff --git a/arch/arm/mach-spear3xx/include/mach/system.h b/arch/arm/mach-spear3xx/include/mach/system.h
deleted file mode 100644
index 92cee63..0000000
--- a/arch/arm/mach-spear3xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/system.h
- *
- * SPEAr3xx Machine family specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <plat/system.h>
-
-#endif /* __MACH_SYSTEM_H */
diff --git a/arch/arm/mach-spear3xx/spear300.c b/arch/arm/mach-spear3xx/spear300.c
index a5e46b4..9da50e281 100644
--- a/arch/arm/mach-spear3xx/spear300.c
+++ b/arch/arm/mach-spear3xx/spear300.c
@@ -430,18 +430,8 @@
.irq_base = SPEAR300_GPIO1_INT_BASE,
};
-struct amba_device spear300_gpio1_device = {
- .dev = {
- .init_name = "gpio1",
- .platform_data = &gpio1_plat_data,
- },
- .res = {
- .start = SPEAR300_GPIO_BASE,
- .end = SPEAR300_GPIO_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {SPEAR300_VIRQ_GPIO1, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear300_gpio1, "gpio1", 0, SPEAR300_GPIO_BASE,
+ {SPEAR300_VIRQ_GPIO1}, &gpio1_plat_data);
/* spear300 routines */
void __init spear300_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c
index 10af45d..b1733c3 100644
--- a/arch/arm/mach-spear3xx/spear3xx.c
+++ b/arch/arm/mach-spear3xx/spear3xx.c
@@ -28,31 +28,12 @@
.irq_base = SPEAR3XX_GPIO_INT_BASE,
};
-struct amba_device spear3xx_gpio_device = {
- .dev = {
- .init_name = "gpio",
- .platform_data = &gpio_plat_data,
- },
- .res = {
- .start = SPEAR3XX_ICM3_GPIO_BASE,
- .end = SPEAR3XX_ICM3_GPIO_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {SPEAR3XX_IRQ_BASIC_GPIO, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear3xx_gpio, "gpio", 0, SPEAR3XX_ICM3_GPIO_BASE,
+ {SPEAR3XX_IRQ_BASIC_GPIO}, &gpio_plat_data);
/* uart device registration */
-struct amba_device spear3xx_uart_device = {
- .dev = {
- .init_name = "uart",
- },
- .res = {
- .start = SPEAR3XX_ICM1_UART_BASE,
- .end = SPEAR3XX_ICM1_UART_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {SPEAR3XX_IRQ_UART, NO_IRQ},
-};
+AMBA_APB_DEVICE(spear3xx_uart, "uart", 0, SPEAR3XX_ICM1_UART_BASE,
+ {SPEAR3XX_IRQ_UART}, NULL);
/* Do spear3xx familiy common initialization part here */
void __init spear3xx_init(void)
diff --git a/arch/arm/mach-spear6xx/include/mach/system.h b/arch/arm/mach-spear6xx/include/mach/system.h
deleted file mode 100644
index 0b1d2be..0000000
--- a/arch/arm/mach-spear6xx/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-spear6xx/include/mach/system.h
- *
- * SPEAr6xx Machine family specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_SYSTEM_H
-#define __MACH_SYSTEM_H
-
-#include <plat/system.h>
-
-#endif /* __MACH_SYSTEM_H */
diff --git a/arch/arm/mach-spear6xx/spear6xx.c b/arch/arm/mach-spear6xx/spear6xx.c
index e0f6628..b997b1b 100644
--- a/arch/arm/mach-spear6xx/spear6xx.c
+++ b/arch/arm/mach-spear6xx/spear6xx.c
@@ -34,7 +34,7 @@
.end = SPEAR6XX_ICM1_UART0_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
- .irq = {IRQ_UART_0, NO_IRQ},
+ .irq = {IRQ_UART_0},
}, {
.dev = {
.init_name = "uart1",
@@ -44,7 +44,7 @@
.end = SPEAR6XX_ICM1_UART1_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
- .irq = {IRQ_UART_1, NO_IRQ},
+ .irq = {IRQ_UART_1},
}
};
@@ -73,7 +73,7 @@
.end = SPEAR6XX_CPU_GPIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
- .irq = {IRQ_LOCAL_GPIO, NO_IRQ},
+ .irq = {IRQ_LOCAL_GPIO},
}, {
.dev = {
.init_name = "gpio1",
@@ -84,7 +84,7 @@
.end = SPEAR6XX_ICM3_GPIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
- .irq = {IRQ_BASIC_GPIO, NO_IRQ},
+ .irq = {IRQ_BASIC_GPIO},
}, {
.dev = {
.init_name = "gpio2",
@@ -95,7 +95,7 @@
.end = SPEAR6XX_ICM2_GPIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
- .irq = {IRQ_APPL_GPIO, NO_IRQ},
+ .irq = {IRQ_APPL_GPIO},
}
};
diff --git a/arch/arm/mach-tegra/board-dt-tegra20.c b/arch/arm/mach-tegra/board-dt-tegra20.c
index 7a95e0b..e20b419 100644
--- a/arch/arm/mach-tegra/board-dt-tegra20.c
+++ b/arch/arm/mach-tegra/board-dt-tegra20.c
@@ -131,11 +131,7 @@
}
static const char *tegra20_dt_board_compat[] = {
- "compulab,trimslice",
- "nvidia,harmony",
- "compal,paz00",
- "nvidia,seaboard",
- "nvidia,ventana",
+ "nvidia,tegra20",
NULL
};
diff --git a/arch/arm/mach-tegra/board-dt-tegra30.c b/arch/arm/mach-tegra/board-dt-tegra30.c
index 3c197e2..6db4df2 100644
--- a/arch/arm/mach-tegra/board-dt-tegra30.c
+++ b/arch/arm/mach-tegra/board-dt-tegra30.c
@@ -47,7 +47,7 @@
}
static const char *tegra30_dt_board_compat[] = {
- "nvidia,cardhu",
+ "nvidia,tegra30",
NULL
};
diff --git a/arch/arm/mach-tegra/board-harmony-power.c b/arch/arm/mach-tegra/board-harmony-power.c
index 21d1285..c0298b3 100644
--- a/arch/arm/mach-tegra/board-harmony-power.c
+++ b/arch/arm/mach-tegra/board-harmony-power.c
@@ -36,13 +36,14 @@
static struct regulator_init_data ldo0_data = {
.constraints = {
- .min_uV = 1250 * 1000,
+ .min_uV = 3300 * 1000,
.max_uV = 3300 * 1000,
.valid_modes_mask = (REGULATOR_MODE_NORMAL |
REGULATOR_MODE_STANDBY),
.valid_ops_mask = (REGULATOR_CHANGE_MODE |
REGULATOR_CHANGE_STATUS |
REGULATOR_CHANGE_VOLTAGE),
+ .apply_uV = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps658621_ldo0_supply),
.consumer_supplies = tps658621_ldo0_supply,
diff --git a/arch/arm/mach-tegra/common.c b/arch/arm/mach-tegra/common.c
index a2eb901..2db20da 100644
--- a/arch/arm/mach-tegra/common.c
+++ b/arch/arm/mach-tegra/common.c
@@ -27,7 +27,6 @@
#include <asm/hardware/gic.h>
#include <mach/iomap.h>
-#include <mach/system.h>
#include "board.h"
#include "clock.h"
@@ -96,6 +95,8 @@
#ifdef CONFIG_ARCH_TEGRA_2x_SOC
void __init tegra20_init_early(void)
{
+ disable_hlt(); /* idle WFI usage needs to be confirmed */
+
tegra_init_fuse();
tegra2_init_clocks();
tegra_clk_init_from_table(tegra20_clk_init_table);
diff --git a/arch/arm/mach-tegra/include/mach/system.h b/arch/arm/mach-tegra/include/mach/system.h
deleted file mode 100644
index a312988..0000000
--- a/arch/arm/mach-tegra/include/mach/system.h
+++ /dev/null
@@ -1,28 +0,0 @@
-/*
- * arch/arm/mach-tegra/include/mach/system.h
- *
- * Copyright (C) 2010 Google, Inc.
- *
- * Author:
- * Colin Cross <ccross@google.com>
- * Erik Gilling <konkers@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __MACH_TEGRA_SYSTEM_H
-#define __MACH_TEGRA_SYSTEM_H
-
-static inline void arch_idle(void)
-{
-}
-
-#endif
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index b4c6926..b986560 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -94,19 +94,9 @@
#endif
};
-static struct amba_device uart0_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "uart0", /* Slow device at 0x3000 offset */
- .platform_data = &uart0_plat_data,
- },
- .res = {
- .start = U300_UART0_BASE,
- .end = U300_UART0_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_U300_UART0, NO_IRQ },
-};
+/* Slow device at 0x3000 offset */
+static AMBA_APB_DEVICE(uart0, "uart0", 0, U300_UART0_BASE,
+ { IRQ_U300_UART0 }, &uart0_plat_data);
/* The U335 have an additional UART1 on the APP CPU */
#ifdef CONFIG_MACH_U300_BS335
@@ -118,71 +108,28 @@
#endif
};
-static struct amba_device uart1_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "uart1", /* Fast device at 0x7000 offset */
- .platform_data = &uart1_plat_data,
- },
- .res = {
- .start = U300_UART1_BASE,
- .end = U300_UART1_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { IRQ_U300_UART1, NO_IRQ },
-};
+/* Fast device at 0x7000 offset */
+static AMBA_APB_DEVICE(uart1, "uart1", 0, U300_UART1_BASE,
+ { IRQ_U300_UART1 }, &uart1_plat_data);
#endif
-static struct amba_device pl172_device = {
- .dev = {
- .init_name = "pl172", /* AHB device at 0x4000 offset */
- .platform_data = NULL,
- },
- .res = {
- .start = U300_EMIF_CFG_BASE,
- .end = U300_EMIF_CFG_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
+/* AHB device at 0x4000 offset */
+static AMBA_APB_DEVICE(pl172, "pl172", 0, U300_EMIF_CFG_BASE, { }, NULL);
/*
* Everything within this next ifdef deals with external devices connected to
* the APP SPI bus.
*/
-static struct amba_device pl022_device = {
- .dev = {
- .coherent_dma_mask = ~0,
- .init_name = "pl022", /* Fast device at 0x6000 offset */
- },
- .res = {
- .start = U300_SPI_BASE,
- .end = U300_SPI_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_U300_SPI, NO_IRQ },
- /*
- * This device has a DMA channel but the Linux driver does not use
- * it currently.
- */
-};
+/* Fast device at 0x6000 offset */
+static AMBA_APB_DEVICE(pl022, "pl022", 0, U300_SPI_BASE,
+ { IRQ_U300_SPI }, NULL);
-static struct amba_device mmcsd_device = {
- .dev = {
- .init_name = "mmci", /* Fast device at 0x1000 offset */
- .platform_data = NULL, /* Added later */
- },
- .res = {
- .start = U300_MMCSD_BASE,
- .end = U300_MMCSD_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = {IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 },
- /*
- * This device has a DMA channel but the Linux driver does not use
- * it currently.
- */
-};
+/* Fast device at 0x1000 offset */
+#define U300_MMCSD_IRQS { IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 }
+
+static AMBA_APB_DEVICE(mmcsd, "mmci", 0, U300_MMCSD_BASE,
+ U300_MMCSD_IRQS, NULL);
/*
* The order of device declaration may be important, since some devices
diff --git a/arch/arm/mach-u300/include/mach/system.h b/arch/arm/mach-u300/include/mach/system.h
deleted file mode 100644
index 574d46e..0000000
--- a/arch/arm/mach-u300/include/mach/system.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/include/mach/system.h
- *
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * System shutdown and reset functions.
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- */
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
diff --git a/arch/arm/mach-ux500/devices-common.c b/arch/arm/mach-ux500/devices-common.c
index c563e54..898a645 100644
--- a/arch/arm/mach-ux500/devices-common.c
+++ b/arch/arm/mach-ux500/devices-common.c
@@ -26,29 +26,22 @@
struct amba_device *dev;
int ret;
- dev = kzalloc(sizeof *dev, GFP_KERNEL);
+ dev = amba_device_alloc(name, base, SZ_4K);
if (!dev)
return ERR_PTR(-ENOMEM);
- dev->dev.init_name = name;
-
- dev->res.start = base;
- dev->res.end = base + SZ_4K - 1;
- dev->res.flags = IORESOURCE_MEM;
-
dev->dma_mask = DMA_BIT_MASK(32);
dev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
dev->irq[0] = irq;
- dev->irq[1] = NO_IRQ;
dev->periphid = periphid;
dev->dev.platform_data = pdata;
- ret = amba_device_register(dev, &iomem_resource);
+ ret = amba_device_add(dev, &iomem_resource);
if (ret) {
- kfree(dev);
+ amba_device_put(dev);
return ERR_PTR(ret);
}
diff --git a/arch/arm/mach-ux500/include/mach/system.h b/arch/arm/mach-ux500/include/mach/system.h
deleted file mode 100644
index 258e5c9..0000000
--- a/arch/arm/mach-ux500/include/mach/system.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/*
- * Copyright (C) 2009 ST-Ericsson.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-versatile/core.c b/arch/arm/mach-versatile/core.c
index 02b7b93..4f352e4 100644
--- a/arch/arm/mach-versatile/core.c
+++ b/arch/arm/mach-versatile/core.c
@@ -582,58 +582,58 @@
.num_chipselect = 1,
};
-#define AACI_IRQ { IRQ_AACI, NO_IRQ }
+#define AACI_IRQ { IRQ_AACI }
#define MMCI0_IRQ { IRQ_MMCI0A,IRQ_SIC_MMCI0B }
-#define KMI0_IRQ { IRQ_SIC_KMI0, NO_IRQ }
-#define KMI1_IRQ { IRQ_SIC_KMI1, NO_IRQ }
+#define KMI0_IRQ { IRQ_SIC_KMI0 }
+#define KMI1_IRQ { IRQ_SIC_KMI1 }
/*
* These devices are connected directly to the multi-layer AHB switch
*/
-#define SMC_IRQ { NO_IRQ, NO_IRQ }
-#define MPMC_IRQ { NO_IRQ, NO_IRQ }
-#define CLCD_IRQ { IRQ_CLCDINT, NO_IRQ }
-#define DMAC_IRQ { IRQ_DMAINT, NO_IRQ }
+#define SMC_IRQ { }
+#define MPMC_IRQ { }
+#define CLCD_IRQ { IRQ_CLCDINT }
+#define DMAC_IRQ { IRQ_DMAINT }
/*
* These devices are connected via the core APB bridge
*/
-#define SCTL_IRQ { NO_IRQ, NO_IRQ }
-#define WATCHDOG_IRQ { IRQ_WDOGINT, NO_IRQ }
-#define GPIO0_IRQ { IRQ_GPIOINT0, NO_IRQ }
-#define GPIO1_IRQ { IRQ_GPIOINT1, NO_IRQ }
-#define RTC_IRQ { IRQ_RTCINT, NO_IRQ }
+#define SCTL_IRQ { }
+#define WATCHDOG_IRQ { IRQ_WDOGINT }
+#define GPIO0_IRQ { IRQ_GPIOINT0 }
+#define GPIO1_IRQ { IRQ_GPIOINT1 }
+#define RTC_IRQ { IRQ_RTCINT }
/*
* These devices are connected via the DMA APB bridge
*/
-#define SCI_IRQ { IRQ_SCIINT, NO_IRQ }
-#define UART0_IRQ { IRQ_UARTINT0, NO_IRQ }
-#define UART1_IRQ { IRQ_UARTINT1, NO_IRQ }
-#define UART2_IRQ { IRQ_UARTINT2, NO_IRQ }
-#define SSP_IRQ { IRQ_SSPINT, NO_IRQ }
+#define SCI_IRQ { IRQ_SCIINT }
+#define UART0_IRQ { IRQ_UARTINT0 }
+#define UART1_IRQ { IRQ_UARTINT1 }
+#define UART2_IRQ { IRQ_UARTINT2 }
+#define SSP_IRQ { IRQ_SSPINT }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
+APB_DEVICE(aaci, "fpga:04", AACI, NULL);
+APB_DEVICE(mmc0, "fpga:05", MMCI0, &mmc0_plat_data);
+APB_DEVICE(kmi0, "fpga:06", KMI0, NULL);
+APB_DEVICE(kmi1, "fpga:07", KMI1, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", SMC, NULL);
-AMBA_DEVICE(mpmc, "dev:10", MPMC, NULL);
-AMBA_DEVICE(clcd, "dev:20", CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "dev:30", DMAC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", SSP, &ssp0_plat_data);
+AHB_DEVICE(smc, "dev:00", SMC, NULL);
+AHB_DEVICE(mpmc, "dev:10", MPMC, NULL);
+AHB_DEVICE(clcd, "dev:20", CLCD, &clcd_plat_data);
+AHB_DEVICE(dmac, "dev:30", DMAC, NULL);
+APB_DEVICE(sctl, "dev:e0", SCTL, NULL);
+APB_DEVICE(wdog, "dev:e1", WATCHDOG, NULL);
+APB_DEVICE(gpio0, "dev:e4", GPIO0, &gpio0_plat_data);
+APB_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
+APB_DEVICE(rtc, "dev:e8", RTC, NULL);
+APB_DEVICE(sci0, "dev:f0", SCI, NULL);
+APB_DEVICE(uart0, "dev:f1", UART0, NULL);
+APB_DEVICE(uart1, "dev:f2", UART1, NULL);
+APB_DEVICE(uart2, "dev:f3", UART2, NULL);
+APB_DEVICE(ssp0, "dev:f4", SSP, &ssp0_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
diff --git a/arch/arm/mach-versatile/core.h b/arch/arm/mach-versatile/core.h
index 2ef2f55..683e607 100644
--- a/arch/arm/mach-versatile/core.h
+++ b/arch/arm/mach-versatile/core.h
@@ -36,20 +36,10 @@
extern struct of_dev_auxdata versatile_auxdata_lookup[];
#endif
-#define AMBA_DEVICE(name,busid,base,plat) \
-static struct amba_device name##_device = { \
- .dev = { \
- .coherent_dma_mask = ~0, \
- .init_name = busid, \
- .platform_data = plat, \
- }, \
- .res = { \
- .start = VERSATILE_##base##_BASE, \
- .end = (VERSATILE_##base##_BASE) + SZ_4K - 1,\
- .flags = IORESOURCE_MEM, \
- }, \
- .dma_mask = ~0, \
- .irq = base##_IRQ, \
-}
+#define APB_DEVICE(name, busid, base, plat) \
+static AMBA_APB_DEVICE(name, busid, 0, VERSATILE_##base##_BASE, base##_IRQ, plat)
+
+#define AHB_DEVICE(name, busid, base, plat) \
+static AMBA_AHB_DEVICE(name, busid, 0, VERSATILE_##base##_BASE, base##_IRQ, plat)
#endif
diff --git a/arch/arm/mach-versatile/include/mach/system.h b/arch/arm/mach-versatile/include/mach/system.h
deleted file mode 100644
index f3fa347..0000000
--- a/arch/arm/mach-versatile/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-versatile/include/mach/system.h
- *
- * Copyright (C) 2003 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-versatile/versatile_pb.c b/arch/arm/mach-versatile/versatile_pb.c
index 9581c19..1973833 100644
--- a/arch/arm/mach-versatile/versatile_pb.c
+++ b/arch/arm/mach-versatile/versatile_pb.c
@@ -58,28 +58,28 @@
.irq_base = IRQ_GPIO3_START,
};
-#define UART3_IRQ { IRQ_SIC_UART3, NO_IRQ }
-#define SCI1_IRQ { IRQ_SIC_SCI3, NO_IRQ }
+#define UART3_IRQ { IRQ_SIC_UART3 }
+#define SCI1_IRQ { IRQ_SIC_SCI3 }
#define MMCI1_IRQ { IRQ_MMCI1A, IRQ_SIC_MMCI1B }
/*
* These devices are connected via the core APB bridge
*/
-#define GPIO2_IRQ { IRQ_GPIOINT2, NO_IRQ }
-#define GPIO3_IRQ { IRQ_GPIOINT3, NO_IRQ }
+#define GPIO2_IRQ { IRQ_GPIOINT2 }
+#define GPIO3_IRQ { IRQ_GPIOINT3 }
/*
* These devices are connected via the DMA APB bridge
*/
/* FPGA Primecells */
-AMBA_DEVICE(uart3, "fpga:09", UART3, NULL);
-AMBA_DEVICE(sci1, "fpga:0a", SCI1, NULL);
-AMBA_DEVICE(mmc1, "fpga:0b", MMCI1, &mmc1_plat_data);
+APB_DEVICE(uart3, "fpga:09", UART3, NULL);
+APB_DEVICE(sci1, "fpga:0a", SCI1, NULL);
+APB_DEVICE(mmc1, "fpga:0b", MMCI1, &mmc1_plat_data);
/* DevChip Primecells */
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(gpio3, "dev:e7", GPIO3, &gpio3_plat_data);
+APB_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
+APB_DEVICE(gpio3, "dev:e7", GPIO3, &gpio3_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&uart3_device,
diff --git a/arch/arm/mach-vexpress/core.h b/arch/arm/mach-vexpress/core.h
index f439715..9f0f282 100644
--- a/arch/arm/mach-vexpress/core.h
+++ b/arch/arm/mach-vexpress/core.h
@@ -1,19 +1,2 @@
#define __MMIO_P2V(x) (((x) & 0xfffff) | (((x) & 0x0f000000) >> 4) | 0xf8000000)
#define MMIO_P2V(x) ((void __iomem *)__MMIO_P2V(x))
-
-#define AMBA_DEVICE(name,busid,base,plat) \
-struct amba_device name##_device = { \
- .dev = { \
- .coherent_dma_mask = ~0UL, \
- .init_name = busid, \
- .platform_data = plat, \
- }, \
- .res = { \
- .start = base, \
- .end = base + SZ_4K - 1, \
- .flags = IORESOURCE_MEM, \
- }, \
- .dma_mask = ~0UL, \
- .irq = IRQ_##base, \
- /* .dma = DMA_##base,*/ \
-}
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index b1e87c1..1b1d2e4 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -109,10 +109,10 @@
.remove = versatile_clcd_remove_dma,
};
-static AMBA_DEVICE(clcd, "ct:clcd", CT_CA9X4_CLCDC, &ct_ca9x4_clcd_data);
-static AMBA_DEVICE(dmc, "ct:dmc", CT_CA9X4_DMC, NULL);
-static AMBA_DEVICE(smc, "ct:smc", CT_CA9X4_SMC, NULL);
-static AMBA_DEVICE(gpio, "ct:gpio", CT_CA9X4_GPIO, NULL);
+static AMBA_AHB_DEVICE(clcd, "ct:clcd", 0, CT_CA9X4_CLCDC, IRQ_CT_CA9X4_CLCDC, &ct_ca9x4_clcd_data);
+static AMBA_APB_DEVICE(dmc, "ct:dmc", 0, CT_CA9X4_DMC, IRQ_CT_CA9X4_DMC, NULL);
+static AMBA_APB_DEVICE(smc, "ct:smc", 0, CT_CA9X4_SMC, IRQ_CT_CA9X4_SMC, NULL);
+static AMBA_APB_DEVICE(gpio, "ct:gpio", 0, CT_CA9X4_GPIO, IRQ_CT_CA9X4_GPIO, NULL);
static struct amba_device *ct_ca9x4_amba_devs[] __initdata = {
&clcd_device,
diff --git a/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h b/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
index a34d3d4..a40468f 100644
--- a/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
+++ b/arch/arm/mach-vexpress/include/mach/ct-ca9x4.h
@@ -35,7 +35,7 @@
* Interrupts. Those in {} are for AMBA devices
*/
#define IRQ_CT_CA9X4_CLCDC { 76 }
-#define IRQ_CT_CA9X4_DMC { -1 }
+#define IRQ_CT_CA9X4_DMC { 0 }
#define IRQ_CT_CA9X4_SMC { 77, 78 }
#define IRQ_CT_CA9X4_TIMER0 80
#define IRQ_CT_CA9X4_TIMER1 81
diff --git a/arch/arm/mach-vexpress/include/mach/system.h b/arch/arm/mach-vexpress/include/mach/system.h
deleted file mode 100644
index f653a8e..0000000
--- a/arch/arm/mach-vexpress/include/mach/system.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-vexpress/include/mach/system.h
- *
- * Copyright (C) 2003 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index b4a28ca..ad64f97 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -266,16 +266,16 @@
.status = v2m_mmci_status,
};
-static AMBA_DEVICE(aaci, "mb:aaci", V2M_AACI, NULL);
-static AMBA_DEVICE(mmci, "mb:mmci", V2M_MMCI, &v2m_mmci_data);
-static AMBA_DEVICE(kmi0, "mb:kmi0", V2M_KMI0, NULL);
-static AMBA_DEVICE(kmi1, "mb:kmi1", V2M_KMI1, NULL);
-static AMBA_DEVICE(uart0, "mb:uart0", V2M_UART0, NULL);
-static AMBA_DEVICE(uart1, "mb:uart1", V2M_UART1, NULL);
-static AMBA_DEVICE(uart2, "mb:uart2", V2M_UART2, NULL);
-static AMBA_DEVICE(uart3, "mb:uart3", V2M_UART3, NULL);
-static AMBA_DEVICE(wdt, "mb:wdt", V2M_WDT, NULL);
-static AMBA_DEVICE(rtc, "mb:rtc", V2M_RTC, NULL);
+static AMBA_APB_DEVICE(aaci, "mb:aaci", 0, V2M_AACI, IRQ_V2M_AACI, NULL);
+static AMBA_APB_DEVICE(mmci, "mb:mmci", 0, V2M_MMCI, IRQ_V2M_MMCI, &v2m_mmci_data);
+static AMBA_APB_DEVICE(kmi0, "mb:kmi0", 0, V2M_KMI0, IRQ_V2M_KMI0, NULL);
+static AMBA_APB_DEVICE(kmi1, "mb:kmi1", 0, V2M_KMI1, IRQ_V2M_KMI1, NULL);
+static AMBA_APB_DEVICE(uart0, "mb:uart0", 0, V2M_UART0, IRQ_V2M_UART0, NULL);
+static AMBA_APB_DEVICE(uart1, "mb:uart1", 0, V2M_UART1, IRQ_V2M_UART1, NULL);
+static AMBA_APB_DEVICE(uart2, "mb:uart2", 0, V2M_UART2, IRQ_V2M_UART2, NULL);
+static AMBA_APB_DEVICE(uart3, "mb:uart3", 0, V2M_UART3, IRQ_V2M_UART3, NULL);
+static AMBA_APB_DEVICE(wdt, "mb:wdt", 0, V2M_WDT, IRQ_V2M_WDT, NULL);
+static AMBA_APB_DEVICE(rtc, "mb:rtc", 0, V2M_RTC, IRQ_V2M_RTC, NULL);
static struct amba_device *v2m_amba_devs[] __initdata = {
&aaci_device,
diff --git a/arch/arm/mach-vt8500/include/mach/system.h b/arch/arm/mach-vt8500/include/mach/system.h
index d6c757e..58fa801 100644
--- a/arch/arm/mach-vt8500/include/mach/system.h
+++ b/arch/arm/mach-vt8500/include/mach/system.h
@@ -7,11 +7,6 @@
/* PM Software Reset request register */
#define VT8500_PMSR_VIRT 0xf8130060
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
static inline void arch_reset(char mode, const char *cmd)
{
writel(1, VT8500_PMSR_VIRT);
diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c
index 78110be..db82568 100644
--- a/arch/arm/mach-w90x900/dev.c
+++ b/arch/arm/mach-w90x900/dev.c
@@ -530,6 +530,7 @@
void __init nuc900_board_init(struct platform_device **device, int size)
{
+ disable_hlt();
platform_add_devices(device, size);
platform_add_devices(nuc900_public_dev, ARRAY_SIZE(nuc900_public_dev));
spi_register_board_info(nuc900_spi_board_info,
diff --git a/arch/arm/mach-w90x900/include/mach/system.h b/arch/arm/mach-w90x900/include/mach/system.h
deleted file mode 100644
index 2aaeb93..0000000
--- a/arch/arm/mach-w90x900/include/mach/system.h
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-w90x900/include/mach/system.h
- *
- * Copyright (c) 2008 Nuvoton technology corporation
- * All rights reserved.
- *
- * Wan ZongShun <mcuos.com@gmail.com>
- *
- * Based on arch/arm/mach-s3c2410/include/mach/system.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-static void arch_idle(void)
-{
-}
diff --git a/arch/arm/mach-zynq/include/mach/system.h b/arch/arm/mach-zynq/include/mach/system.h
deleted file mode 100644
index 8e88e0b..0000000
--- a/arch/arm/mach-zynq/include/mach/system.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/* arch/arm/mach-zynq/include/mach/system.h
- *
- * Copyright (C) 2011 Xilinx
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MACH_SYSTEM_H__
-#define __MACH_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/plat-mxc/include/mach/system.h b/arch/arm/plat-mxc/include/mach/system.h
deleted file mode 100644
index 13ad0df..0000000
--- a/arch/arm/plat-mxc/include/mach/system.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright 2004-2008 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MXC_SYSTEM_H__
-#define __ASM_ARCH_MXC_SYSTEM_H__
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif /* __ASM_ARCH_MXC_SYSTEM_H__ */
diff --git a/arch/arm/plat-omap/include/plat/board-ams-delta.h b/arch/arm/plat-omap/include/plat/board-ams-delta.h
index 51b102d..ad6f865 100644
--- a/arch/arm/plat-omap/include/plat/board-ams-delta.h
+++ b/arch/arm/plat-omap/include/plat/board-ams-delta.h
@@ -28,33 +28,8 @@
#if defined (CONFIG_MACH_AMS_DELTA)
-#define AMS_DELTA_LATCH1_PHYS 0x01000000
-#define AMS_DELTA_LATCH1_VIRT 0xEA000000
-#define AMS_DELTA_MODEM_PHYS 0x04000000
-#define AMS_DELTA_MODEM_VIRT 0xEB000000
-#define AMS_DELTA_LATCH2_PHYS 0x08000000
-#define AMS_DELTA_LATCH2_VIRT 0xEC000000
-
-#define AMS_DELTA_LATCH1_LED_CAMERA 0x01
-#define AMS_DELTA_LATCH1_LED_ADVERT 0x02
-#define AMS_DELTA_LATCH1_LED_EMAIL 0x04
-#define AMS_DELTA_LATCH1_LED_HANDSFREE 0x08
-#define AMS_DELTA_LATCH1_LED_VOICEMAIL 0x10
-#define AMS_DELTA_LATCH1_LED_VOICE 0x20
-
-#define AMS_DELTA_LATCH2_LCD_VBLEN 0x0001
-#define AMS_DELTA_LATCH2_LCD_NDISP 0x0002
-#define AMS_DELTA_LATCH2_NAND_NCE 0x0004
-#define AMS_DELTA_LATCH2_NAND_NRE 0x0008
-#define AMS_DELTA_LATCH2_NAND_NWP 0x0010
-#define AMS_DELTA_LATCH2_NAND_NWE 0x0020
-#define AMS_DELTA_LATCH2_NAND_ALE 0x0040
-#define AMS_DELTA_LATCH2_NAND_CLE 0x0080
-#define AMD_DELTA_LATCH2_KEYBRD_PWR 0x0100
-#define AMD_DELTA_LATCH2_KEYBRD_DATA 0x0200
#define AMD_DELTA_LATCH2_SCARD_RSTIN 0x0400
#define AMD_DELTA_LATCH2_SCARD_CMDVCC 0x0800
-#define AMS_DELTA_LATCH2_MODEM_NRESET 0x1000
#define AMS_DELTA_LATCH2_MODEM_CODEC 0x2000
#define AMS_DELTA_GPIO_PIN_KEYBRD_DATA 0
@@ -66,9 +41,29 @@
#define AMS_DELTA_GPIO_PIN_CONFIG 11
#define AMS_DELTA_GPIO_PIN_NAND_RB 12
+#define AMS_DELTA_GPIO_PIN_LCD_VBLEN 240
+#define AMS_DELTA_GPIO_PIN_LCD_NDISP 241
+#define AMS_DELTA_GPIO_PIN_NAND_NCE 242
+#define AMS_DELTA_GPIO_PIN_NAND_NRE 243
+#define AMS_DELTA_GPIO_PIN_NAND_NWP 244
+#define AMS_DELTA_GPIO_PIN_NAND_NWE 245
+#define AMS_DELTA_GPIO_PIN_NAND_ALE 246
+#define AMS_DELTA_GPIO_PIN_NAND_CLE 247
+#define AMS_DELTA_GPIO_PIN_KEYBRD_PWR 248
+#define AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT 249
+#define AMS_DELTA_GPIO_PIN_SCARD_RSTIN 250
+#define AMS_DELTA_GPIO_PIN_SCARD_CMDVCC 251
+#define AMS_DELTA_GPIO_PIN_MODEM_NRESET 252
+#define AMS_DELTA_GPIO_PIN_MODEM_CODEC 253
+
+#define AMS_DELTA_LATCH2_GPIO_BASE AMS_DELTA_GPIO_PIN_LCD_VBLEN
+#define AMS_DELTA_LATCH2_NGPIO 16
+
#ifndef __ASSEMBLY__
-void ams_delta_latch1_write(u8 mask, u8 value);
-void ams_delta_latch2_write(u16 mask, u16 value);
+void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value);
+#define ams_delta_latch2_write(mask, value) \
+ ams_delta_latch_write(AMS_DELTA_LATCH2_GPIO_BASE, \
+ AMS_DELTA_LATCH2_NGPIO, (mask), (value))
#endif
#endif /* CONFIG_MACH_AMS_DELTA */
diff --git a/arch/arm/plat-omap/include/plat/system.h b/arch/arm/plat-omap/include/plat/system.h
deleted file mode 100644
index 8e5ebd7..0000000
--- a/arch/arm/plat-omap/include/plat/system.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * Copied from arch/arm/mach-sa1100/include/mach/system.h
- * Copyright (c) 1999 Nicolas Pitre <nico@fluxnic.net>
- */
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <asm/proc-fns.h>
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-#endif
diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c
index 21f1fda..32a0993 100644
--- a/arch/arm/plat-s3c24xx/cpu.c
+++ b/arch/arm/plat-s3c24xx/cpu.c
@@ -32,6 +32,7 @@
#include <linux/io.h>
#include <mach/hardware.h>
+#include <mach/regs-clock.h>
#include <asm/irq.h>
#include <asm/cacheflush.h>
@@ -190,8 +191,34 @@
return __raw_readl(S3C2410_GSTATUS1);
}
+static void s3c24xx_default_idle(void)
+{
+ unsigned long tmp;
+ int i;
+
+ /* idle the system by using the idle mode which will wait for an
+ * interrupt to happen before restarting the system.
+ */
+
+ /* Warning: going into idle state upsets jtag scanning */
+
+ __raw_writel(__raw_readl(S3C2410_CLKCON) | S3C2410_CLKCON_IDLE,
+ S3C2410_CLKCON);
+
+ /* the samsung port seems to do a loop and then unset idle.. */
+ for (i = 0; i < 50; i++)
+ tmp += __raw_readl(S3C2410_CLKCON); /* ensure loop not optimised out */
+
+ /* this bit is not cleared on re-start... */
+
+ __raw_writel(__raw_readl(S3C2410_CLKCON) & ~S3C2410_CLKCON_IDLE,
+ S3C2410_CLKCON);
+}
+
void __init s3c24xx_init_io(struct map_desc *mach_desc, int size)
{
+ arm_pm_idle = s3c24xx_default_idle;
+
/* initialise the io descriptors we need for initialisation */
iotable_init(mach_desc, size);
iotable_init(s3c_iodesc, ARRAY_SIZE(s3c_iodesc));
diff --git a/arch/arm/plat-spear/include/plat/system.h b/arch/arm/plat-spear/include/plat/system.h
deleted file mode 100644
index 86c6f83..0000000
--- a/arch/arm/plat-spear/include/plat/system.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/system.h
- *
- * SPEAr platform specific architecture functions
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_SYSTEM_H
-#define __PLAT_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- /*
- * This should do all the clock switching
- * and wait for interrupt tricks
- */
- cpu_do_idle();
-}
-
-#endif /* __PLAT_SYSTEM_H */
diff --git a/drivers/amba/bus.c b/drivers/amba/bus.c
index 54eaf96..01c2cf4 100644
--- a/drivers/amba/bus.c
+++ b/drivers/amba/bus.c
@@ -497,37 +497,22 @@
}
/**
- * amba_device_register - register an AMBA device
- * @dev: AMBA device to register
- * @parent: parent memory resource
+ * amba_device_add - add a previously allocated AMBA device structure
+ * @dev: AMBA device allocated by amba_device_alloc
+ * @parent: resource parent for this devices resources
*
- * Setup the AMBA device, reading the cell ID if present.
- * Claim the resource, and register the AMBA device with
- * the Linux device manager.
+ * Claim the resource, and read the device cell ID if not already
+ * initialized. Register the AMBA device with the Linux device
+ * manager.
*/
-int amba_device_register(struct amba_device *dev, struct resource *parent)
+int amba_device_add(struct amba_device *dev, struct resource *parent)
{
u32 size;
void __iomem *tmp;
int i, ret;
- device_initialize(&dev->dev);
-
- /*
- * Copy from device_add
- */
- if (dev->dev.init_name) {
- dev_set_name(&dev->dev, "%s", dev->dev.init_name);
- dev->dev.init_name = NULL;
- }
-
- dev->dev.release = amba_device_release;
- dev->dev.bus = &amba_bustype;
- dev->dev.dma_mask = &dev->dma_mask;
- dev->res.name = dev_name(&dev->dev);
-
- if (!dev->dev.coherent_dma_mask && dev->dma_mask)
- dev_warn(&dev->dev, "coherent dma mask is unset\n");
+ WARN_ON(dev->irq[0] == (unsigned int)-1);
+ WARN_ON(dev->irq[1] == (unsigned int)-1);
ret = request_resource(parent, &dev->res);
if (ret)
@@ -582,9 +567,9 @@
if (ret)
goto err_release;
- if (dev->irq[0] != NO_IRQ)
+ if (dev->irq[0] && dev->irq[0] != NO_IRQ)
ret = device_create_file(&dev->dev, &dev_attr_irq0);
- if (ret == 0 && dev->irq[1] != NO_IRQ)
+ if (ret == 0 && dev->irq[1] && dev->irq[1] != NO_IRQ)
ret = device_create_file(&dev->dev, &dev_attr_irq1);
if (ret == 0)
return ret;
@@ -596,6 +581,74 @@
err_out:
return ret;
}
+EXPORT_SYMBOL_GPL(amba_device_add);
+
+static void amba_device_initialize(struct amba_device *dev, const char *name)
+{
+ device_initialize(&dev->dev);
+ if (name)
+ dev_set_name(&dev->dev, "%s", name);
+ dev->dev.release = amba_device_release;
+ dev->dev.bus = &amba_bustype;
+ dev->dev.dma_mask = &dev->dma_mask;
+ dev->res.name = dev_name(&dev->dev);
+}
+
+/**
+ * amba_device_alloc - allocate an AMBA device
+ * @name: sysfs name of the AMBA device
+ * @base: base of AMBA device
+ * @size: size of AMBA device
+ *
+ * Allocate and initialize an AMBA device structure. Returns %NULL
+ * on failure.
+ */
+struct amba_device *amba_device_alloc(const char *name, resource_size_t base,
+ size_t size)
+{
+ struct amba_device *dev;
+
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (dev) {
+ amba_device_initialize(dev, name);
+ dev->res.start = base;
+ dev->res.end = base + size - 1;
+ dev->res.flags = IORESOURCE_MEM;
+ }
+
+ return dev;
+}
+EXPORT_SYMBOL_GPL(amba_device_alloc);
+
+/**
+ * amba_device_register - register an AMBA device
+ * @dev: AMBA device to register
+ * @parent: parent memory resource
+ *
+ * Setup the AMBA device, reading the cell ID if present.
+ * Claim the resource, and register the AMBA device with
+ * the Linux device manager.
+ */
+int amba_device_register(struct amba_device *dev, struct resource *parent)
+{
+ amba_device_initialize(dev, dev->dev.init_name);
+ dev->dev.init_name = NULL;
+
+ if (!dev->dev.coherent_dma_mask && dev->dma_mask)
+ dev_warn(&dev->dev, "coherent dma mask is unset\n");
+
+ return amba_device_add(dev, parent);
+}
+
+/**
+ * amba_device_put - put an AMBA device
+ * @dev: AMBA device to put
+ */
+void amba_device_put(struct amba_device *dev)
+{
+ put_device(&dev->dev);
+}
+EXPORT_SYMBOL_GPL(amba_device_put);
/**
* amba_device_unregister - unregister an AMBA device
diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c
index d4d08bd..bd5b10e 100644
--- a/drivers/input/serio/ams_delta_serio.c
+++ b/drivers/input/serio/ams_delta_serio.c
@@ -92,8 +92,7 @@
static int ams_delta_serio_open(struct serio *serio)
{
/* enable keyboard */
- ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR,
- AMD_DELTA_LATCH2_KEYBRD_PWR);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 1);
return 0;
}
@@ -101,9 +100,32 @@
static void ams_delta_serio_close(struct serio *serio)
{
/* disable keyboard */
- ams_delta_latch2_write(AMD_DELTA_LATCH2_KEYBRD_PWR, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_KEYBRD_PWR, 0);
}
+static const struct gpio ams_delta_gpios[] __initconst_or_module = {
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATA,
+ .flags = GPIOF_DIR_IN,
+ .label = "serio-data",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_CLK,
+ .flags = GPIOF_DIR_IN,
+ .label = "serio-clock",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_PWR,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "serio-power",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_KEYBRD_DATAOUT,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "serio-dataout",
+ },
+};
+
static int __init ams_delta_serio_init(void)
{
int err;
@@ -123,19 +145,12 @@
strlcpy(ams_delta_serio->phys, "GPIO/serio0",
sizeof(ams_delta_serio->phys));
- err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_DATA, "serio-data");
+ err = gpio_request_array(ams_delta_gpios,
+ ARRAY_SIZE(ams_delta_gpios));
if (err) {
- pr_err("ams_delta_serio: Couldn't request gpio pin for data\n");
+ pr_err("ams_delta_serio: Couldn't request gpio pins\n");
goto serio;
}
- gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
-
- err = gpio_request(AMS_DELTA_GPIO_PIN_KEYBRD_CLK, "serio-clock");
- if (err) {
- pr_err("ams_delta_serio: couldn't request gpio pin for clock\n");
- goto gpio_data;
- }
- gpio_direction_input(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
err = request_irq(gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK),
ams_delta_serio_interrupt, IRQ_TYPE_EDGE_RISING,
@@ -143,7 +158,7 @@
if (err < 0) {
pr_err("ams_delta_serio: couldn't request gpio interrupt %d\n",
gpio_to_irq(AMS_DELTA_GPIO_PIN_KEYBRD_CLK));
- goto gpio_clk;
+ goto gpio;
}
/*
* Since GPIO register handling for keyboard clock pin is performed
@@ -157,10 +172,9 @@
dev_info(&ams_delta_serio->dev, "%s\n", ams_delta_serio->name);
return 0;
-gpio_clk:
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
-gpio_data:
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+gpio:
+ gpio_free_array(ams_delta_gpios,
+ ARRAY_SIZE(ams_delta_gpios));
serio:
kfree(ams_delta_serio);
return err;
@@ -171,7 +185,7 @@
{
serio_unregister_port(ams_delta_serio);
free_irq(OMAP_GPIO_IRQ(AMS_DELTA_GPIO_PIN_KEYBRD_CLK), 0);
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_CLK);
- gpio_free(AMS_DELTA_GPIO_PIN_KEYBRD_DATA);
+ gpio_free_array(ams_delta_gpios,
+ ARRAY_SIZE(ams_delta_gpios));
}
module_exit(ams_delta_serio_exit);
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 9ca28fc..f5d5c03 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -74,13 +74,6 @@
This option enables support for LEDs connected to GPIO lines
on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
-config LEDS_AMS_DELTA
- tristate "LED Support for the Amstrad Delta (E3)"
- depends on LEDS_CLASS
- depends on MACH_AMS_DELTA
- help
- This option enables support for the LEDs on Amstrad Delta (E3).
-
config LEDS_NET48XX
tristate "LED Support for Soekris net48xx series Error LED"
depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 1fc6875..8cab1bb 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -12,7 +12,6 @@
obj-$(CONFIG_LEDS_LM3530) += leds-lm3530.o
obj-$(CONFIG_LEDS_MIKROTIK_RB532) += leds-rb532.o
obj-$(CONFIG_LEDS_S3C24XX) += leds-s3c24xx.o
-obj-$(CONFIG_LEDS_AMS_DELTA) += leds-ams-delta.o
obj-$(CONFIG_LEDS_NET48XX) += leds-net48xx.o
obj-$(CONFIG_LEDS_NET5501) += leds-net5501.o
obj-$(CONFIG_LEDS_WRAP) += leds-wrap.o
diff --git a/drivers/leds/leds-ams-delta.c b/drivers/leds/leds-ams-delta.c
deleted file mode 100644
index 0742835..0000000
--- a/drivers/leds/leds-ams-delta.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * LEDs driver for Amstrad Delta (E3)
- *
- * Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <plat/board-ams-delta.h>
-
-/*
- * Our context
- */
-struct ams_delta_led {
- struct led_classdev cdev;
- u8 bitmask;
-};
-
-static void ams_delta_led_set(struct led_classdev *led_cdev,
- enum led_brightness value)
-{
- struct ams_delta_led *led_dev =
- container_of(led_cdev, struct ams_delta_led, cdev);
-
- if (value)
- ams_delta_latch1_write(led_dev->bitmask, led_dev->bitmask);
- else
- ams_delta_latch1_write(led_dev->bitmask, 0);
-}
-
-static struct ams_delta_led ams_delta_leds[] = {
- {
- .cdev = {
- .name = "ams-delta::camera",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_CAMERA,
- },
- {
- .cdev = {
- .name = "ams-delta::advert",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_ADVERT,
- },
- {
- .cdev = {
- .name = "ams-delta::email",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_EMAIL,
- },
- {
- .cdev = {
- .name = "ams-delta::handsfree",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_HANDSFREE,
- },
- {
- .cdev = {
- .name = "ams-delta::voicemail",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_VOICEMAIL,
- },
- {
- .cdev = {
- .name = "ams-delta::voice",
- .brightness_set = ams_delta_led_set,
- },
- .bitmask = AMS_DELTA_LATCH1_LED_VOICE,
- },
-};
-
-static int ams_delta_led_probe(struct platform_device *pdev)
-{
- int i, ret;
-
- for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++) {
- ams_delta_leds[i].cdev.flags |= LED_CORE_SUSPENDRESUME;
- ret = led_classdev_register(&pdev->dev,
- &ams_delta_leds[i].cdev);
- if (ret < 0)
- goto fail;
- }
-
- return 0;
-fail:
- while (--i >= 0)
- led_classdev_unregister(&ams_delta_leds[i].cdev);
- return ret;
-}
-
-static int ams_delta_led_remove(struct platform_device *pdev)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(ams_delta_leds); i++)
- led_classdev_unregister(&ams_delta_leds[i].cdev);
-
- return 0;
-}
-
-static struct platform_driver ams_delta_led_driver = {
- .probe = ams_delta_led_probe,
- .remove = ams_delta_led_remove,
- .driver = {
- .name = "ams-delta-led",
- .owner = THIS_MODULE,
- },
-};
-
-module_platform_driver(ams_delta_led_driver);
-
-MODULE_AUTHOR("Jonathan McDowell <noodles@earth.li>");
-MODULE_DESCRIPTION("Amstrad Delta LED driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:ams-delta-led");
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 0d955ff..304f2f9 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1325,7 +1325,7 @@
if (ret)
goto unmap;
- if (dev->irq[1] == NO_IRQ)
+ if (dev->irq[1] == NO_IRQ || !dev->irq[1])
host->singleirq = true;
else {
ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED,
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c
index 3197e97..7341695 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/ams-delta.c
@@ -26,7 +26,7 @@
#include <asm/io.h>
#include <mach/hardware.h>
#include <asm/sizes.h>
-#include <asm/gpio.h>
+#include <linux/gpio.h>
#include <plat/board-ams-delta.h>
/*
@@ -34,8 +34,6 @@
*/
static struct mtd_info *ams_delta_mtd = NULL;
-#define NAND_MASK (AMS_DELTA_LATCH2_NAND_NRE | AMS_DELTA_LATCH2_NAND_NWE | AMS_DELTA_LATCH2_NAND_CLE | AMS_DELTA_LATCH2_NAND_ALE | AMS_DELTA_LATCH2_NAND_NCE | AMS_DELTA_LATCH2_NAND_NWP)
-
/*
* Define partitions for flash devices
*/
@@ -68,10 +66,9 @@
writew(0, io_base + OMAP_MPUIO_IO_CNTL);
writew(byte, this->IO_ADDR_W);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 0);
ndelay(40);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NWE,
- AMS_DELTA_LATCH2_NAND_NWE);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NWE, 1);
}
static u_char ams_delta_read_byte(struct mtd_info *mtd)
@@ -80,12 +77,11 @@
struct nand_chip *this = mtd->priv;
void __iomem *io_base = this->priv;
- ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 0);
ndelay(40);
writew(~0, io_base + OMAP_MPUIO_IO_CNTL);
res = readw(this->IO_ADDR_R);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_NRE,
- AMS_DELTA_LATCH2_NAND_NRE);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NRE, 1);
return res;
}
@@ -132,15 +128,12 @@
{
if (ctrl & NAND_CTRL_CHANGE) {
- unsigned long bits;
-
- bits = (~ctrl & NAND_NCE) ? AMS_DELTA_LATCH2_NAND_NCE : 0;
- bits |= (ctrl & NAND_CLE) ? AMS_DELTA_LATCH2_NAND_CLE : 0;
- bits |= (ctrl & NAND_ALE) ? AMS_DELTA_LATCH2_NAND_ALE : 0;
-
- ams_delta_latch2_write(AMS_DELTA_LATCH2_NAND_CLE |
- AMS_DELTA_LATCH2_NAND_ALE |
- AMS_DELTA_LATCH2_NAND_NCE, bits);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_NCE,
+ (ctrl & NAND_NCE) == 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_CLE,
+ (ctrl & NAND_CLE) != 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_NAND_ALE,
+ (ctrl & NAND_ALE) != 0);
}
if (cmd != NAND_CMD_NONE)
@@ -152,6 +145,39 @@
return gpio_get_value(AMS_DELTA_GPIO_PIN_NAND_RB);
}
+static const struct gpio _mandatory_gpio[] = {
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_NCE,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "nand_nce",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_NRE,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "nand_nre",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_NWP,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "nand_nwp",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_NWE,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "nand_nwe",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_ALE,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "nand_ale",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_NAND_CLE,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "nand_cle",
+ },
+};
+
/*
* Main initialization routine
*/
@@ -223,10 +249,9 @@
platform_set_drvdata(pdev, io_base);
/* Set chip enabled, but */
- ams_delta_latch2_write(NAND_MASK, AMS_DELTA_LATCH2_NAND_NRE |
- AMS_DELTA_LATCH2_NAND_NWE |
- AMS_DELTA_LATCH2_NAND_NCE |
- AMS_DELTA_LATCH2_NAND_NWP);
+ err = gpio_request_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+ if (err)
+ goto out_gpio;
/* Scan to find existence of the device */
if (nand_scan(ams_delta_mtd, 1)) {
@@ -241,7 +266,10 @@
goto out;
out_mtd:
+ gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+out_gpio:
platform_set_drvdata(pdev, NULL);
+ gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB);
iounmap(io_base);
out_release_io:
release_mem_region(res->start, resource_size(res));
@@ -262,6 +290,8 @@
/* Release resources, unregister device */
nand_release(ams_delta_mtd);
+ gpio_free_array(_mandatory_gpio, ARRAY_SIZE(_mandatory_gpio));
+ gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB);
iounmap(io_base);
release_mem_region(res->start, resource_size(res));
diff --git a/drivers/of/platform.c b/drivers/of/platform.c
index 63b3ec4..cae9477 100644
--- a/drivers/of/platform.c
+++ b/drivers/of/platform.c
@@ -253,7 +253,7 @@
if (!of_device_is_available(node))
return NULL;
- dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ dev = amba_device_alloc(NULL, 0, 0);
if (!dev)
return NULL;
@@ -283,14 +283,14 @@
if (ret)
goto err_free;
- ret = amba_device_register(dev, &iomem_resource);
+ ret = amba_device_add(dev, &iomem_resource);
if (ret)
goto err_free;
return dev;
err_free:
- kfree(dev);
+ amba_device_put(dev);
return NULL;
}
#else /* CONFIG_ARM_AMBA */
diff --git a/drivers/video/omap/lcd_ams_delta.c b/drivers/video/omap/lcd_ams_delta.c
index 0fdd6f6..d3a3113 100644
--- a/drivers/video/omap/lcd_ams_delta.c
+++ b/drivers/video/omap/lcd_ams_delta.c
@@ -25,6 +25,7 @@
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/lcd.h>
+#include <linux/gpio.h>
#include <plat/board-ams-delta.h>
#include <mach/hardware.h>
@@ -98,29 +99,41 @@
/* omapfb panel section */
+static const struct gpio _gpios[] = {
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_LCD_VBLEN,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "lcd_vblen",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_LCD_NDISP,
+ .flags = GPIOF_OUT_INIT_LOW,
+ .label = "lcd_ndisp",
+ },
+};
+
static int ams_delta_panel_init(struct lcd_panel *panel,
struct omapfb_device *fbdev)
{
- return 0;
+ return gpio_request_array(_gpios, ARRAY_SIZE(_gpios));
}
static void ams_delta_panel_cleanup(struct lcd_panel *panel)
{
+ gpio_free_array(_gpios, ARRAY_SIZE(_gpios));
}
static int ams_delta_panel_enable(struct lcd_panel *panel)
{
- ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP,
- AMS_DELTA_LATCH2_LCD_NDISP);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN,
- AMS_DELTA_LATCH2_LCD_VBLEN);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 1);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 1);
return 0;
}
static void ams_delta_panel_disable(struct lcd_panel *panel)
{
- ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_VBLEN, 0);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_LCD_NDISP, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_VBLEN, 0);
+ gpio_set_value(AMS_DELTA_GPIO_PIN_LCD_NDISP, 0);
}
static unsigned long ams_delta_panel_get_caps(struct lcd_panel *panel)
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h
index 724c69c..a9fab83 100644
--- a/include/linux/amba/bus.h
+++ b/include/linux/amba/bus.h
@@ -60,6 +60,9 @@
int amba_driver_register(struct amba_driver *);
void amba_driver_unregister(struct amba_driver *);
+struct amba_device *amba_device_alloc(const char *, resource_size_t, size_t);
+void amba_device_put(struct amba_device *);
+int amba_device_add(struct amba_device *, struct resource *);
int amba_device_register(struct amba_device *, struct resource *);
void amba_device_unregister(struct amba_device *);
struct amba_device *amba_find_device(const char *, struct device *, unsigned int, unsigned int);
@@ -89,4 +92,37 @@
#define amba_manf(d) AMBA_MANF_BITS((d)->periphid)
#define amba_part(d) AMBA_PART_BITS((d)->periphid)
+#define __AMBA_DEV(busid, data, mask) \
+ { \
+ .coherent_dma_mask = mask, \
+ .init_name = busid, \
+ .platform_data = data, \
+ }
+
+/*
+ * APB devices do not themselves have the ability to address memory,
+ * so DMA masks should be zero (much like USB peripheral devices.)
+ * The DMA controller DMA masks should be used instead (much like
+ * USB host controllers in conventional PCs.)
+ */
+#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) \
+struct amba_device name##_device = { \
+ .dev = __AMBA_DEV(busid, data, 0), \
+ .res = DEFINE_RES_MEM(base, SZ_4K), \
+ .irq = irqs, \
+ .periphid = id, \
+}
+
+/*
+ * AHB devices are DMA capable, so set their DMA masks
+ */
+#define AMBA_AHB_DEVICE(name, busid, id, base, irqs, data) \
+struct amba_device name##_device = { \
+ .dev = __AMBA_DEV(busid, data, ~0ULL), \
+ .res = DEFINE_RES_MEM(base, SZ_4K), \
+ .dma_mask = ~0ULL, \
+ .irq = irqs, \
+ .periphid = id, \
+}
+
#endif
diff --git a/sound/soc/omap/ams-delta.c b/sound/soc/omap/ams-delta.c
index a67f437..f610260 100644
--- a/sound/soc/omap/ams-delta.c
+++ b/sound/soc/omap/ams-delta.c
@@ -426,29 +426,6 @@
};
-/* Board specific codec bias level control */
-static int ams_delta_set_bias_level(struct snd_soc_card *card,
- struct snd_soc_dapm_context *dapm,
- enum snd_soc_bias_level level)
-{
- switch (level) {
- case SND_SOC_BIAS_ON:
- case SND_SOC_BIAS_PREPARE:
- case SND_SOC_BIAS_STANDBY:
- if (card->dapm.bias_level == SND_SOC_BIAS_OFF)
- ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_NRESET,
- AMS_DELTA_LATCH2_MODEM_NRESET);
- break;
- case SND_SOC_BIAS_OFF:
- if (card->dapm.bias_level != SND_SOC_BIAS_OFF)
- ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_NRESET,
- 0);
- }
- card->dapm.bias_level = level;
-
- return 0;
-}
-
/* Digital mute implemented using modem/CPU multiplexer.
* Shares hardware with codec config pulse generation */
static bool ams_delta_muted = 1;
@@ -512,9 +489,6 @@
ams_delta_ops.shutdown = ams_delta_shutdown;
}
- /* Set codec bias level */
- ams_delta_set_bias_level(card, dapm, SND_SOC_BIAS_STANDBY);
-
/* Add hook switch - can be used to control the codec from userspace
* even if line discipline fails */
ret = snd_soc_jack_new(rtd->codec, "hook_switch",
@@ -598,7 +572,6 @@
.owner = THIS_MODULE,
.dai_link = &ams_delta_dai_link,
.num_links = 1,
- .set_bias_level = ams_delta_set_bias_level,
};
/* Module init/exit */
@@ -635,7 +608,7 @@
platform_device_put(ams_delta_audio_platform_device);
return ret;
}
-module_init(ams_delta_module_init);
+late_initcall(ams_delta_module_init);
static void __exit ams_delta_module_exit(void)
{
@@ -647,11 +620,6 @@
ARRAY_SIZE(ams_delta_hook_switch_gpios),
ams_delta_hook_switch_gpios);
- /* Keep modem power on */
- ams_delta_set_bias_level(&ams_delta_audio_card,
- &ams_delta_audio_card.rtd[0].codec->dapm,
- SND_SOC_BIAS_STANDBY);
-
platform_device_unregister(cx20442_platform_device);
platform_device_unregister(ams_delta_audio_platform_device);
}