| /* |
| * pmbus.h - Common defines and structures for PMBus devices |
| * |
| * Copyright (c) 2010, 2011 Ericsson AB. |
| * Copyright (c) 2012 Guenter Roeck |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #ifndef PMBUS_H |
| #define PMBUS_H |
| |
| /* |
| * Registers |
| */ |
| #define PMBUS_PAGE 0x00 |
| #define PMBUS_OPERATION 0x01 |
| #define PMBUS_ON_OFF_CONFIG 0x02 |
| #define PMBUS_CLEAR_FAULTS 0x03 |
| #define PMBUS_PHASE 0x04 |
| |
| #define PMBUS_CAPABILITY 0x19 |
| #define PMBUS_QUERY 0x1A |
| |
| #define PMBUS_VOUT_MODE 0x20 |
| #define PMBUS_VOUT_COMMAND 0x21 |
| #define PMBUS_VOUT_TRIM 0x22 |
| #define PMBUS_VOUT_CAL_OFFSET 0x23 |
| #define PMBUS_VOUT_MAX 0x24 |
| #define PMBUS_VOUT_MARGIN_HIGH 0x25 |
| #define PMBUS_VOUT_MARGIN_LOW 0x26 |
| #define PMBUS_VOUT_TRANSITION_RATE 0x27 |
| #define PMBUS_VOUT_DROOP 0x28 |
| #define PMBUS_VOUT_SCALE_LOOP 0x29 |
| #define PMBUS_VOUT_SCALE_MONITOR 0x2A |
| |
| #define PMBUS_COEFFICIENTS 0x30 |
| #define PMBUS_POUT_MAX 0x31 |
| |
| #define PMBUS_FAN_CONFIG_12 0x3A |
| #define PMBUS_FAN_COMMAND_1 0x3B |
| #define PMBUS_FAN_COMMAND_2 0x3C |
| #define PMBUS_FAN_CONFIG_34 0x3D |
| #define PMBUS_FAN_COMMAND_3 0x3E |
| #define PMBUS_FAN_COMMAND_4 0x3F |
| |
| #define PMBUS_VOUT_OV_FAULT_LIMIT 0x40 |
| #define PMBUS_VOUT_OV_FAULT_RESPONSE 0x41 |
| #define PMBUS_VOUT_OV_WARN_LIMIT 0x42 |
| #define PMBUS_VOUT_UV_WARN_LIMIT 0x43 |
| #define PMBUS_VOUT_UV_FAULT_LIMIT 0x44 |
| #define PMBUS_VOUT_UV_FAULT_RESPONSE 0x45 |
| #define PMBUS_IOUT_OC_FAULT_LIMIT 0x46 |
| #define PMBUS_IOUT_OC_FAULT_RESPONSE 0x47 |
| #define PMBUS_IOUT_OC_LV_FAULT_LIMIT 0x48 |
| #define PMBUS_IOUT_OC_LV_FAULT_RESPONSE 0x49 |
| #define PMBUS_IOUT_OC_WARN_LIMIT 0x4A |
| #define PMBUS_IOUT_UC_FAULT_LIMIT 0x4B |
| #define PMBUS_IOUT_UC_FAULT_RESPONSE 0x4C |
| |
| #define PMBUS_OT_FAULT_LIMIT 0x4F |
| #define PMBUS_OT_FAULT_RESPONSE 0x50 |
| #define PMBUS_OT_WARN_LIMIT 0x51 |
| #define PMBUS_UT_WARN_LIMIT 0x52 |
| #define PMBUS_UT_FAULT_LIMIT 0x53 |
| #define PMBUS_UT_FAULT_RESPONSE 0x54 |
| #define PMBUS_VIN_OV_FAULT_LIMIT 0x55 |
| #define PMBUS_VIN_OV_FAULT_RESPONSE 0x56 |
| #define PMBUS_VIN_OV_WARN_LIMIT 0x57 |
| #define PMBUS_VIN_UV_WARN_LIMIT 0x58 |
| #define PMBUS_VIN_UV_FAULT_LIMIT 0x59 |
| |
| #define PMBUS_IIN_OC_FAULT_LIMIT 0x5B |
| #define PMBUS_IIN_OC_WARN_LIMIT 0x5D |
| |
| #define PMBUS_POUT_OP_FAULT_LIMIT 0x68 |
| #define PMBUS_POUT_OP_WARN_LIMIT 0x6A |
| #define PMBUS_PIN_OP_WARN_LIMIT 0x6B |
| |
| #define PMBUS_STATUS_BYTE 0x78 |
| #define PMBUS_STATUS_WORD 0x79 |
| #define PMBUS_STATUS_VOUT 0x7A |
| #define PMBUS_STATUS_IOUT 0x7B |
| #define PMBUS_STATUS_INPUT 0x7C |
| #define PMBUS_STATUS_TEMPERATURE 0x7D |
| #define PMBUS_STATUS_CML 0x7E |
| #define PMBUS_STATUS_OTHER 0x7F |
| #define PMBUS_STATUS_MFR_SPECIFIC 0x80 |
| #define PMBUS_STATUS_FAN_12 0x81 |
| #define PMBUS_STATUS_FAN_34 0x82 |
| |
| #define PMBUS_READ_VIN 0x88 |
| #define PMBUS_READ_IIN 0x89 |
| #define PMBUS_READ_VCAP 0x8A |
| #define PMBUS_READ_VOUT 0x8B |
| #define PMBUS_READ_IOUT 0x8C |
| #define PMBUS_READ_TEMPERATURE_1 0x8D |
| #define PMBUS_READ_TEMPERATURE_2 0x8E |
| #define PMBUS_READ_TEMPERATURE_3 0x8F |
| #define PMBUS_READ_FAN_SPEED_1 0x90 |
| #define PMBUS_READ_FAN_SPEED_2 0x91 |
| #define PMBUS_READ_FAN_SPEED_3 0x92 |
| #define PMBUS_READ_FAN_SPEED_4 0x93 |
| #define PMBUS_READ_DUTY_CYCLE 0x94 |
| #define PMBUS_READ_FREQUENCY 0x95 |
| #define PMBUS_READ_POUT 0x96 |
| #define PMBUS_READ_PIN 0x97 |
| |
| #define PMBUS_REVISION 0x98 |
| #define PMBUS_MFR_ID 0x99 |
| #define PMBUS_MFR_MODEL 0x9A |
| #define PMBUS_MFR_REVISION 0x9B |
| #define PMBUS_MFR_LOCATION 0x9C |
| #define PMBUS_MFR_DATE 0x9D |
| #define PMBUS_MFR_SERIAL 0x9E |
| |
| /* |
| * Virtual registers. |
| * Useful to support attributes which are not supported by standard PMBus |
| * registers but exist as manufacturer specific registers on individual chips. |
| * Must be mapped to real registers in device specific code. |
| * |
| * Semantics: |
| * Virtual registers are all word size. |
| * READ registers are read-only; writes are either ignored or return an error. |
| * RESET registers are read/write. Reading reset registers returns zero |
| * (used for detection), writing any value causes the associated history to be |
| * reset. |
| * Virtual registers have to be handled in device specific driver code. Chip |
| * driver code returns non-negative register values if a virtual register is |
| * supported, or a negative error code if not. The chip driver may return |
| * -ENODATA or any other error code in this case, though an error code other |
| * than -ENODATA is handled more efficiently and thus preferred. Either case, |
| * the calling PMBus core code will abort if the chip driver returns an error |
| * code when reading or writing virtual registers. |
| */ |
| #define PMBUS_VIRT_BASE 0x100 |
| #define PMBUS_VIRT_READ_TEMP_AVG (PMBUS_VIRT_BASE + 0) |
| #define PMBUS_VIRT_READ_TEMP_MIN (PMBUS_VIRT_BASE + 1) |
| #define PMBUS_VIRT_READ_TEMP_MAX (PMBUS_VIRT_BASE + 2) |
| #define PMBUS_VIRT_RESET_TEMP_HISTORY (PMBUS_VIRT_BASE + 3) |
| #define PMBUS_VIRT_READ_VIN_AVG (PMBUS_VIRT_BASE + 4) |
| #define PMBUS_VIRT_READ_VIN_MIN (PMBUS_VIRT_BASE + 5) |
| #define PMBUS_VIRT_READ_VIN_MAX (PMBUS_VIRT_BASE + 6) |
| #define PMBUS_VIRT_RESET_VIN_HISTORY (PMBUS_VIRT_BASE + 7) |
| #define PMBUS_VIRT_READ_IIN_AVG (PMBUS_VIRT_BASE + 8) |
| #define PMBUS_VIRT_READ_IIN_MIN (PMBUS_VIRT_BASE + 9) |
| #define PMBUS_VIRT_READ_IIN_MAX (PMBUS_VIRT_BASE + 10) |
| #define PMBUS_VIRT_RESET_IIN_HISTORY (PMBUS_VIRT_BASE + 11) |
| #define PMBUS_VIRT_READ_PIN_AVG (PMBUS_VIRT_BASE + 12) |
| #define PMBUS_VIRT_READ_PIN_MAX (PMBUS_VIRT_BASE + 13) |
| #define PMBUS_VIRT_RESET_PIN_HISTORY (PMBUS_VIRT_BASE + 14) |
| #define PMBUS_VIRT_READ_POUT_AVG (PMBUS_VIRT_BASE + 15) |
| #define PMBUS_VIRT_READ_POUT_MAX (PMBUS_VIRT_BASE + 16) |
| #define PMBUS_VIRT_RESET_POUT_HISTORY (PMBUS_VIRT_BASE + 17) |
| #define PMBUS_VIRT_READ_VOUT_AVG (PMBUS_VIRT_BASE + 18) |
| #define PMBUS_VIRT_READ_VOUT_MIN (PMBUS_VIRT_BASE + 19) |
| #define PMBUS_VIRT_READ_VOUT_MAX (PMBUS_VIRT_BASE + 20) |
| #define PMBUS_VIRT_RESET_VOUT_HISTORY (PMBUS_VIRT_BASE + 21) |
| #define PMBUS_VIRT_READ_IOUT_AVG (PMBUS_VIRT_BASE + 22) |
| #define PMBUS_VIRT_READ_IOUT_MIN (PMBUS_VIRT_BASE + 23) |
| #define PMBUS_VIRT_READ_IOUT_MAX (PMBUS_VIRT_BASE + 24) |
| #define PMBUS_VIRT_RESET_IOUT_HISTORY (PMBUS_VIRT_BASE + 25) |
| #define PMBUS_VIRT_READ_TEMP2_AVG (PMBUS_VIRT_BASE + 26) |
| #define PMBUS_VIRT_READ_TEMP2_MIN (PMBUS_VIRT_BASE + 27) |
| #define PMBUS_VIRT_READ_TEMP2_MAX (PMBUS_VIRT_BASE + 28) |
| #define PMBUS_VIRT_RESET_TEMP2_HISTORY (PMBUS_VIRT_BASE + 29) |
| |
| #define PMBUS_VIRT_READ_VMON (PMBUS_VIRT_BASE + 30) |
| #define PMBUS_VIRT_VMON_UV_WARN_LIMIT (PMBUS_VIRT_BASE + 31) |
| #define PMBUS_VIRT_VMON_OV_WARN_LIMIT (PMBUS_VIRT_BASE + 32) |
| #define PMBUS_VIRT_VMON_UV_FAULT_LIMIT (PMBUS_VIRT_BASE + 33) |
| #define PMBUS_VIRT_VMON_OV_FAULT_LIMIT (PMBUS_VIRT_BASE + 34) |
| #define PMBUS_VIRT_STATUS_VMON (PMBUS_VIRT_BASE + 35) |
| |
| /* |
| * CAPABILITY |
| */ |
| #define PB_CAPABILITY_SMBALERT (1<<4) |
| #define PB_CAPABILITY_ERROR_CHECK (1<<7) |
| |
| /* |
| * VOUT_MODE |
| */ |
| #define PB_VOUT_MODE_MODE_MASK 0xe0 |
| #define PB_VOUT_MODE_PARAM_MASK 0x1f |
| |
| #define PB_VOUT_MODE_LINEAR 0x00 |
| #define PB_VOUT_MODE_VID 0x20 |
| #define PB_VOUT_MODE_DIRECT 0x40 |
| |
| /* |
| * Fan configuration |
| */ |
| #define PB_FAN_2_PULSE_MASK ((1 << 0) | (1 << 1)) |
| #define PB_FAN_2_RPM (1 << 2) |
| #define PB_FAN_2_INSTALLED (1 << 3) |
| #define PB_FAN_1_PULSE_MASK ((1 << 4) | (1 << 5)) |
| #define PB_FAN_1_RPM (1 << 6) |
| #define PB_FAN_1_INSTALLED (1 << 7) |
| |
| /* |
| * STATUS_BYTE, STATUS_WORD (lower) |
| */ |
| #define PB_STATUS_NONE_ABOVE (1<<0) |
| #define PB_STATUS_CML (1<<1) |
| #define PB_STATUS_TEMPERATURE (1<<2) |
| #define PB_STATUS_VIN_UV (1<<3) |
| #define PB_STATUS_IOUT_OC (1<<4) |
| #define PB_STATUS_VOUT_OV (1<<5) |
| #define PB_STATUS_OFF (1<<6) |
| #define PB_STATUS_BUSY (1<<7) |
| |
| /* |
| * STATUS_WORD (upper) |
| */ |
| #define PB_STATUS_UNKNOWN (1<<8) |
| #define PB_STATUS_OTHER (1<<9) |
| #define PB_STATUS_FANS (1<<10) |
| #define PB_STATUS_POWER_GOOD_N (1<<11) |
| #define PB_STATUS_WORD_MFR (1<<12) |
| #define PB_STATUS_INPUT (1<<13) |
| #define PB_STATUS_IOUT_POUT (1<<14) |
| #define PB_STATUS_VOUT (1<<15) |
| |
| /* |
| * STATUS_IOUT |
| */ |
| #define PB_POUT_OP_WARNING (1<<0) |
| #define PB_POUT_OP_FAULT (1<<1) |
| #define PB_POWER_LIMITING (1<<2) |
| #define PB_CURRENT_SHARE_FAULT (1<<3) |
| #define PB_IOUT_UC_FAULT (1<<4) |
| #define PB_IOUT_OC_WARNING (1<<5) |
| #define PB_IOUT_OC_LV_FAULT (1<<6) |
| #define PB_IOUT_OC_FAULT (1<<7) |
| |
| /* |
| * STATUS_VOUT, STATUS_INPUT |
| */ |
| #define PB_VOLTAGE_UV_FAULT (1<<4) |
| #define PB_VOLTAGE_UV_WARNING (1<<5) |
| #define PB_VOLTAGE_OV_WARNING (1<<6) |
| #define PB_VOLTAGE_OV_FAULT (1<<7) |
| |
| /* |
| * STATUS_INPUT |
| */ |
| #define PB_PIN_OP_WARNING (1<<0) |
| #define PB_IIN_OC_WARNING (1<<1) |
| #define PB_IIN_OC_FAULT (1<<2) |
| |
| /* |
| * STATUS_TEMPERATURE |
| */ |
| #define PB_TEMP_UT_FAULT (1<<4) |
| #define PB_TEMP_UT_WARNING (1<<5) |
| #define PB_TEMP_OT_WARNING (1<<6) |
| #define PB_TEMP_OT_FAULT (1<<7) |
| |
| /* |
| * STATUS_FAN |
| */ |
| #define PB_FAN_AIRFLOW_WARNING (1<<0) |
| #define PB_FAN_AIRFLOW_FAULT (1<<1) |
| #define PB_FAN_FAN2_SPEED_OVERRIDE (1<<2) |
| #define PB_FAN_FAN1_SPEED_OVERRIDE (1<<3) |
| #define PB_FAN_FAN2_WARNING (1<<4) |
| #define PB_FAN_FAN1_WARNING (1<<5) |
| #define PB_FAN_FAN2_FAULT (1<<6) |
| #define PB_FAN_FAN1_FAULT (1<<7) |
| |
| /* |
| * CML_FAULT_STATUS |
| */ |
| #define PB_CML_FAULT_OTHER_MEM_LOGIC (1<<0) |
| #define PB_CML_FAULT_OTHER_COMM (1<<1) |
| #define PB_CML_FAULT_PROCESSOR (1<<3) |
| #define PB_CML_FAULT_MEMORY (1<<4) |
| #define PB_CML_FAULT_PACKET_ERROR (1<<5) |
| #define PB_CML_FAULT_INVALID_DATA (1<<6) |
| #define PB_CML_FAULT_INVALID_COMMAND (1<<7) |
| |
| enum pmbus_sensor_classes { |
| PSC_VOLTAGE_IN = 0, |
| PSC_VOLTAGE_OUT, |
| PSC_CURRENT_IN, |
| PSC_CURRENT_OUT, |
| PSC_POWER, |
| PSC_TEMPERATURE, |
| PSC_FAN, |
| PSC_NUM_CLASSES /* Number of power sensor classes */ |
| }; |
| |
| #define PMBUS_PAGES 32 /* Per PMBus specification */ |
| |
| /* Functionality bit mask */ |
| #define PMBUS_HAVE_VIN (1 << 0) |
| #define PMBUS_HAVE_VCAP (1 << 1) |
| #define PMBUS_HAVE_VOUT (1 << 2) |
| #define PMBUS_HAVE_IIN (1 << 3) |
| #define PMBUS_HAVE_IOUT (1 << 4) |
| #define PMBUS_HAVE_PIN (1 << 5) |
| #define PMBUS_HAVE_POUT (1 << 6) |
| #define PMBUS_HAVE_FAN12 (1 << 7) |
| #define PMBUS_HAVE_FAN34 (1 << 8) |
| #define PMBUS_HAVE_TEMP (1 << 9) |
| #define PMBUS_HAVE_TEMP2 (1 << 10) |
| #define PMBUS_HAVE_TEMP3 (1 << 11) |
| #define PMBUS_HAVE_STATUS_VOUT (1 << 12) |
| #define PMBUS_HAVE_STATUS_IOUT (1 << 13) |
| #define PMBUS_HAVE_STATUS_INPUT (1 << 14) |
| #define PMBUS_HAVE_STATUS_TEMP (1 << 15) |
| #define PMBUS_HAVE_STATUS_FAN12 (1 << 16) |
| #define PMBUS_HAVE_STATUS_FAN34 (1 << 17) |
| #define PMBUS_HAVE_VMON (1 << 18) |
| #define PMBUS_HAVE_STATUS_VMON (1 << 19) |
| |
| enum pmbus_data_format { linear = 0, direct, vid }; |
| |
| struct pmbus_driver_info { |
| int pages; /* Total number of pages */ |
| enum pmbus_data_format format[PSC_NUM_CLASSES]; |
| /* |
| * Support one set of coefficients for each sensor type |
| * Used for chips providing data in direct mode. |
| */ |
| int m[PSC_NUM_CLASSES]; /* mantissa for direct data format */ |
| int b[PSC_NUM_CLASSES]; /* offset */ |
| int R[PSC_NUM_CLASSES]; /* exponent */ |
| |
| u32 func[PMBUS_PAGES]; /* Functionality, per page */ |
| /* |
| * The following functions map manufacturing specific register values |
| * to PMBus standard register values. Specify only if mapping is |
| * necessary. |
| * Functions return the register value (read) or zero (write) if |
| * successful. A return value of -ENODATA indicates that there is no |
| * manufacturer specific register, but that a standard PMBus register |
| * may exist. Any other negative return value indicates that the |
| * register does not exist, and that no attempt should be made to read |
| * the standard register. |
| */ |
| int (*read_byte_data)(struct i2c_client *client, int page, int reg); |
| int (*read_word_data)(struct i2c_client *client, int page, int reg); |
| int (*write_word_data)(struct i2c_client *client, int page, int reg, |
| u16 word); |
| int (*write_byte)(struct i2c_client *client, int page, u8 value); |
| /* |
| * The identify function determines supported PMBus functionality. |
| * This function is only necessary if a chip driver supports multiple |
| * chips, and the chip functionality is not pre-determined. |
| */ |
| int (*identify)(struct i2c_client *client, |
| struct pmbus_driver_info *info); |
| }; |
| |
| /* Function declarations */ |
| |
| void pmbus_clear_cache(struct i2c_client *client); |
| int pmbus_set_page(struct i2c_client *client, u8 page); |
| int pmbus_read_word_data(struct i2c_client *client, u8 page, u8 reg); |
| int pmbus_write_word_data(struct i2c_client *client, u8 page, u8 reg, u16 word); |
| int pmbus_read_byte_data(struct i2c_client *client, int page, u8 reg); |
| int pmbus_write_byte(struct i2c_client *client, int page, u8 value); |
| void pmbus_clear_faults(struct i2c_client *client); |
| bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg); |
| bool pmbus_check_word_register(struct i2c_client *client, int page, int reg); |
| int pmbus_do_probe(struct i2c_client *client, const struct i2c_device_id *id, |
| struct pmbus_driver_info *info); |
| int pmbus_do_remove(struct i2c_client *client); |
| const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client |
| *client); |
| |
| #endif /* PMBUS_H */ |