| Qualcomm technologies inc. Internet Packet Accelerator |
| |
| Internet Packet Accelerator (IPA) is a programmable protocol |
| processor HW block. It is designed to support generic HW processing |
| of UL/DL IP packets for various use cases independent of radio technology. |
| |
| Required properties: |
| |
| IPA node: |
| |
| - compatible : "qcom,ipa" |
| - reg: Specifies the base physical addresses and the sizes of the IPA |
| registers. |
| - reg-names: "ipa-base" - string to identify the IPA CORE base registers. |
| "bam-base" - string to identify the IPA BAM base registers. |
| "a2-bam-base" - string to identify the A2 BAM base registers. |
| - interrupts: Specifies the interrupt associated with IPA. |
| - interrupt-names: "ipa-irq" - string to identify the IPA core interrupt. |
| "bam-irq" - string to identify the IPA BAM interrupt. |
| "a2-bam-irq" - string to identify the A2 BAM interrupt. |
| - qcom,ipa-hw-ver: Specifies the IPA hardware version. |
| - qcom,ipa-ram-mmap: An array of unsigned integers representing addresses and |
| sizes which are used by the driver to access IPA RAM. |
| |
| Optional: |
| |
| - qcom,wan-rx-ring-size: size of WAN rx ring, default is 192 |
| - qcom,lan-rx-ring-size: size of LAN rx ring, default is 192 |
| - qcom,arm-smmu: SMMU is present and ARM SMMU driver is used |
| - qcom,msm-smmu: SMMU is present and QSMMU driver is used |
| - qcom,smmu-fast-map: Boolean context flag to set SMMU to fastpath mode |
| - ipa_smmu_ap: AP general purpose SMMU device |
| compatible "qcom,ipa-smmu-ap-cb" |
| - ipa_smmu_wlan: WDI SMMU device |
| compatible "qcom,ipa-smmu-wlan-cb" |
| - ipa_smmu_uc: uc SMMU device |
| compatible "qcom,ipa-smmu-uc-cb" |
| - qcom,use-a2-service: determine if A2 service will be used |
| - qcom,use-ipa-tethering-bridge: determine if tethering bridge will be used |
| - qcom,use-ipa-bamdma-a2-bridge: determine if a2/ipa hw bridge will be used |
| - qcom,ee: which EE is assigned to (non-secure) APPS from IPA-BAM POV. This |
| is a number |
| - qcom,ipa-hw-mode: IPA hardware mode - Normal, Virtual memory allocation, |
| memory allocation over a PCIe bridge |
| - qcom,msm-bus,name: String representing the client-name |
| - qcom,msm-bus,num-cases: Total number of usecases |
| - qcom,msm-bus,active-only: Boolean context flag for requests in active or |
| dual (active & sleep) contex |
| - qcom,msm-bus,num-paths: Total number of master-slave pairs |
| - qcom,msm-bus,vectors-KBps: Arrays of unsigned integers representing: |
| master-id, slave-id, arbitrated bandwidth |
| in KBps, instantaneous bandwidth in KBps |
| - qcom,ipa-bam-remote-mode: Boolean context flag to determine if ipa bam |
| is in remote mode. |
| - qcom,modem-cfg-emb-pipe-flt: Boolean context flag to determine if modem |
| configures embedded pipe filtering rules |
| - qcom,skip-uc-pipe-reset: Boolean context flag to indicate whether |
| a pipe reset via the IPA uC is required |
| - qcom,ipa-wdi2: Boolean context flag to indicate whether |
| using wdi-2.0 or not |
| - qcom,bandwidth-vote-for-ipa: Boolean context flag to indicate whether |
| ipa clock voting is done by bandwidth |
| voting via msm-bus-scale driver or not |
| - qcom,use-64-bit-dma-mask: Boolean context flag to indicate whether |
| using 64bit dma mask or not |
| - qcom,use-dma-zone: Boolean context flag to indicate whether memory |
| allocations controlled by IPA driver that do not |
| specify a struct device * should use GFP_DMA to |
| workaround IPA HW limitations |
| - qcom,use-rg10-limitation-mitigation: Boolean context flag to activate |
| the mitigation to register group 10 |
| AP access limitation |
| - qcom,do-not-use-ch-gsi-20: Boolean context flag to activate |
| software workaround for IPA limitation |
| to not use GSI physical channel 20 |
| - qcom,tethered-flow-control: Boolean context flag to indicate whether |
| apps based flow control is needed for tethered |
| call. |
| - qcom,rx-polling-sleep-ms: Receive Polling Timeout in millisecond, |
| default is 1 millisecond. |
| - qcom,ipa-polling-iteration: IPA Polling Iteration Count,default is 40. |
| - qcom,mhi-event-ring-id-limits: Two elements property. Start and End limits |
| for MHI event rings ids. |
| - qcom,ipa-tz-unlock-reg: Register start addresses and ranges which |
| need to be unlocked by TZ. |
| - qcom,ipa-uc-monitor-holb: Boolean context flag to indicate whether |
| monitoring of holb via IPA uc is required. |
| |
| IPA pipe sub nodes (A2 static pipes configurations): |
| |
| -label: two labels are supported, a2-to-ipa and ipa-to-a2 which |
| supply static configuration for A2-IPA connection. |
| -qcom,src-bam-physical-address: The physical address of the source BAM |
| -qcom,ipa-bam-mem-type:The memory type: |
| 0(Pipe memory), 1(Private memory), 2(System memory) |
| -qcom,src-bam-pipe-index: Source pipe index |
| -qcom,dst-bam-physical-address: The physical address of the |
| destination BAM |
| -qcom,dst-bam-pipe-index: Destination pipe index |
| -qcom,data-fifo-offset: Data fifo base offset |
| -qcom,data-fifo-size: Data fifo size (bytes) |
| -qcom,descriptor-fifo-offset: Descriptor fifo base offset |
| -qcom,descriptor-fifo-size: Descriptor fifo size (bytes) |
| |
| Optional properties: |
| -qcom,ipa-pipe-mem: Specifies the base physical address and the |
| size of the IPA pipe memory region. |
| Pipe memory is a feature which may be supported by the |
| target (HW platform). The Driver support using pipe |
| memory instead of system memory. In case this property |
| will not appear in the IPA DTS entry, the driver will |
| use system memory. |
| - clocks: This property shall provide a list of entries each of which |
| contains a phandle to clock controller device and a macro that is |
| the clock's name in hardware.This should be "clock_rpm" as clock |
| controller phandle and "clk_ipa_clk" as macro for "iface_clk" |
| - clock-names: This property shall contain the clock input names used |
| by driver in same order as the clocks property.This should be "iface_clk" |
| |
| IPA SMMU sub nodes |
| |
| -compatible: "qcom,ipa-smmu-ap-cb" - represents the AP context bank. |
| |
| -compatible: "qcom,ipa-smmu-wlan-cb" - represents IPA WLAN context bank. |
| |
| -compatible: "qcom,ipa-smmu-uc-cb" - represents IPA uC context bank (for uC |
| offload scenarios). |
| |
| - qcom,smmu-s1-bypass: Boolean context flag to set SMMU to S1 bypass. |
| |
| - iommus : the phandle and stream IDs for the SMMU used by this root |
| |
| - qcom,iova-mapping: specifies the start address and size of iova space. |
| |
| - qcom,additional-mapping: specifies any addtional mapping needed for this |
| context bank. The format is <iova pa size> |
| |
| - qcom,ipa-q6-smem-size: specifies the Q6 SMEM partition size |
| |
| IPA SMP2P sub nodes |
| |
| -compatible: "qcom,smp2pgpio-map-ipa-1-out" - represents the out gpio from |
| ipa driver to modem. |
| |
| -compatible: "qcom,smp2pgpio-map-ipa-1-in" - represents the in gpio to |
| ipa driver from modem. |
| |
| -gpios: Binding to the gpio defined in XXX-smp2p.dtsi |
| |
| |
| Example: |
| |
| qcom,ipa@fd4c0000 { |
| compatible = "qcom,ipa"; |
| reg = <0xfd4c0000 0x26000>, |
| <0xfd4c4000 0x14818>; |
| <0xfc834000 0x7000>; |
| reg-names = "ipa-base", "bam-base"; "a2-bam-base"; |
| interrupts = <0 252 0>, |
| <0 253 0>; |
| <0 29 1>; |
| interrupt-names = "ipa-irq", "bam-irq"; "a2-bam-irq"; |
| qcom,ipa-hw-ver = <1>; |
| clocks = <&clock_rpm clk_ipa_clk>; |
| clock-names = "iface_clk"; |
| |
| qcom,msm-bus,name = "ipa"; |
| qcom,msm-bus,num-cases = <3>; |
| qcom,msm-bus,num-paths = <2>; |
| qcom,msm-bus,vectors-KBps = |
| <90 512 0 0>, <90 585 0 0>, /* No vote */ |
| <90 512 100000 800000>, <90 585 100000 800000>, /* SVS */ |
| <90 512 100000 1200000>, <90 585 100000 1200000>; /* PERF */ |
| qcom,bus-vector-names = "MIN", "SVS", "PERF"; |
| |
| qcom,pipe1 { |
| label = "a2-to-ipa"; |
| qcom,src-bam-physical-address = <0xfc834000>; |
| qcom,ipa-bam-mem-type = <0>; |
| qcom,src-bam-pipe-index = <1>; |
| qcom,dst-bam-physical-address = <0xfd4c0000>; |
| qcom,dst-bam-pipe-index = <6>; |
| qcom,data-fifo-offset = <0x1000>; |
| qcom,data-fifo-size = <0xd00>; |
| qcom,descriptor-fifo-offset = <0x1d00>; |
| qcom,descriptor-fifo-size = <0x300>; |
| }; |
| |
| qcom,pipe2 { |
| label = "ipa-to-a2"; |
| qcom,src-bam-physical-address = <0xfd4c0000>; |
| qcom,ipa-bam-mem-type = <0>; |
| qcom,src-bam-pipe-index = <7>; |
| qcom,dst-bam-physical-address = <0xfc834000>; |
| qcom,dst-bam-pipe-index = <0>; |
| qcom,data-fifo-offset = <0x00>; |
| qcom,data-fifo-size = <0xd00>; |
| qcom,descriptor-fifo-offset = <0xd00>; |
| qcom,descriptor-fifo-size = <0x300>; |
| }; |
| |
| /* smp2p gpio information */ |
| qcom,smp2pgpio_map_ipa_1_out { |
| compatible = "qcom,smp2pgpio-map-ipa-1-out"; |
| gpios = <&smp2pgpio_ipa_1_out 0 0>; |
| }; |
| |
| qcom,smp2pgpio_map_ipa_1_in { |
| compatible = "qcom,smp2pgpio-map-ipa-1-in"; |
| gpios = <&smp2pgpio_ipa_1_in 0 0>; |
| }; |
| |
| ipa_smmu_ap: ipa_smmu_ap { |
| compatible = "qcom,ipa-smmu-ap-cb"; |
| iommus = <&apps_smmu 0x720>; |
| qcom,iova-mapping = <0x20000000 0x40000000>; |
| qcom,additional-mapping = |
| /* modem tables in IMEM */ |
| <0x146bd000 0x146bd000 0x2000>; |
| }; |
| |
| ipa_smmu_wlan: ipa_smmu_wlan { |
| compatible = "qcom,ipa-smmu-wlan-cb"; |
| iommus = <&apps_smmu 0x721>; |
| qcom,additional-mapping = |
| /* ipa-uc ram */ |
| <0x1e60000 0x1e60000 0x80000>; |
| }; |
| |
| ipa_smmu_uc: ipa_smmu_uc { |
| compatible = "qcom,ipa-smmu-uc-cb"; |
| iommus = <&apps_smmu 0x722>; |
| qcom,iova-mapping = <0x40000000 0x20000000>; |
| }; |
| }; |