| # |
| # USB Storage driver configuration |
| # |
| |
| comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'" |
| comment "may also be needed; see USB_STORAGE Help for more information" |
| depends on USB |
| |
| config USB_STORAGE |
| tristate "USB Mass Storage support" |
| depends on USB && SCSI |
| ---help--- |
| Say Y here if you want to connect USB mass storage devices to your |
| computer's USB port. This is the driver you need for USB |
| floppy drives, USB hard disks, USB tape drives, USB CD-ROMs, |
| USB flash devices, and memory sticks, along with |
| similar devices. This driver may also be used for some cameras |
| and card readers. |
| |
| This option depends on 'SCSI' support being enabled, but you |
| probably also need 'SCSI device support: SCSI disk support' |
| (BLK_DEV_SD) for most USB storage devices. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called usb-storage. |
| |
| config USB_STORAGE_DEBUG |
| bool "USB Mass Storage verbose debug" |
| depends on USB_STORAGE |
| help |
| Say Y here in order to have the USB Mass Storage code generate |
| verbose debugging messages. |
| |
| config USB_STORAGE_DATAFAB |
| bool "Datafab Compact Flash Reader support (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Support for certain Datafab CompactFlash readers. |
| Datafab has a web page at <http://www.datafabusa.com/>. |
| |
| config USB_STORAGE_FREECOM |
| bool "Freecom USB/ATAPI Bridge support" |
| depends on USB_STORAGE |
| help |
| Support for the Freecom USB to IDE/ATAPI adaptor. |
| Freecom has a web page at <http://www.freecom.de/>. |
| |
| config USB_STORAGE_ISD200 |
| bool "ISD-200 USB/ATA Bridge support" |
| depends on USB_STORAGE |
| ---help--- |
| Say Y here if you want to use USB Mass Store devices based |
| on the In-Systems Design ISD-200 USB/ATA bridge. |
| |
| Some of the products that use this chip are: |
| |
| - Archos Jukebox 6000 |
| - ISD SmartCable for Storage |
| - Taiwan Skymaster CD530U/DEL-0241 IDE bridge |
| - Sony CRX10U CD-R/RW drive |
| - CyQ've CQ8060A CDRW drive |
| - Planex eXtreme Drive RX-25HU USB-IDE cable (not model RX-25U) |
| |
| config USB_STORAGE_DPCM |
| bool "Microtech/ZiO! CompactFlash/SmartMedia support" |
| depends on USB_STORAGE |
| help |
| Say Y here to support the Microtech/ZiO! CompactFlash reader. |
| There is a web page at <http://www.ziocorp.com/products/>. |
| |
| config USB_STORAGE_USBAT |
| bool "USBAT/USBAT02-based storage support (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support storage devices |
| based on the SCM/Shuttle USBAT/USBAT02 processors. |
| |
| Devices reported to work with this driver include: |
| - CompactFlash reader included with Kodak DC3800 camera |
| - Dane-Elec Zmate CompactFlash reader |
| - Delkin Efilm reader2 |
| - HP 8200e/8210e/8230e CD-Writer Plus drives |
| - I-JAM JS-50U |
| - Jessops CompactFlash JESDCFRU BLACK |
| - Kingston Technology PCREAD-USB/CF |
| - Maxell UA4 CompactFlash reader |
| - Memorex UCF-100 |
| - Microtech ZiO! ICS-45 CF2 |
| - RCA LYRA MP3 portable |
| - Sandisk ImageMate SDDR-05b |
| |
| config USB_STORAGE_SDDR09 |
| bool "SanDisk SDDR-09 (and other SmartMedia) support (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support the Sandisk SDDR-09 |
| SmartMedia reader in the USB Mass Storage driver. |
| Also works for the Microtech Zio! SmartMedia reader. |
| |
| config USB_STORAGE_SDDR55 |
| bool "SanDisk SDDR-55 SmartMedia support (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support the Sandisk SDDR-55 |
| SmartMedia reader in the USB Mass Storage driver. |
| |
| config USB_STORAGE_JUMPSHOT |
| bool "Lexar Jumpshot Compact Flash Reader (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support the Lexar Jumpshot |
| USB CompactFlash reader. |
| |
| config USB_STORAGE_ALAUDA |
| bool "Olympus MAUSB-10/Fuji DPC-R1 support (EXPERIMENTAL)" |
| depends on USB_STORAGE && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support the Olympus MAUSB-10 |
| and Fujifilm DPC-R1 USB Card reader/writer devices. |
| |
| These devices are based on the Alauda chip and support both |
| XD and SmartMedia cards. |
| |
| config USB_STORAGE_ONETOUCH |
| bool "Support OneTouch Button on Maxtor Hard Drives (EXPERIMENTAL)" |
| depends on USB_STORAGE && INPUT_EVDEV && EXPERIMENTAL |
| help |
| Say Y here to include additional code to support the Maxtor OneTouch |
| USB hard drive's onetouch button. |
| |
| This code registers the button on the front of Maxtor OneTouch USB |
| hard drive's as an input device. An action can be associated with |
| this input in any keybinding software. (e.g. gnome's keyboard short- |
| cuts) |
| |
| config USB_STORAGE_KARMA |
| bool "Support for Rio Karma music player" |
| depends on USB_STORAGE |
| help |
| Say Y here to include additional code to support the Rio Karma |
| USB interface. |
| |
| This code places the Rio Karma into mass storage mode, enabling |
| it to be mounted as an ordinary filesystem. Performing an eject |
| on the resulting scsi device node returns the Karma to normal |
| operation. |
| |
| config USB_STORAGE_CYPRESS_ATACB |
| bool "SAT emulation on Cypress USB/ATA Bridge with ATACB" |
| depends on USB_STORAGE |
| ---help--- |
| Say Y here if you want to use SAT (ata pass through) on devices based |
| on the Cypress USB/ATA bridge supporting ATACB. This will allow you |
| to use tools to tune and monitor your drive (like hdparm or smartctl). |
| |
| If you say no here your device will still work with the standard usb |
| mass storage class. |
| |
| config USB_LIBUSUAL |
| bool "The shared table of common (or usual) storage devices" |
| depends on USB |
| help |
| This module contains a table of common (or usual) devices |
| for usb-storage and ub drivers, and allows to switch binding |
| of these devices without rebuilding modules. |
| |
| Typical syntax of /etc/modprobe.conf is: |
| |
| options libusual bias="ub" |
| |
| If unsure, say N. |