drivers/net/usb/Kconfig - kernel/msm-4.9 - Gitiles

 #
 # USB Network devices configuration
 #
 comment "Networking support is needed for USB Network Adapter support"
 	depends on USB && !NET

 menu "USB Network Adapters"
 	depends on USB && NET

 config USB_CATC
 	tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
 	depends on EXPERIMENTAL
 	select CRC32
 	---help---
 	  Say Y if you want to use one of the following 10Mbps USB Ethernet
 	  device based on the EL1210A chip. Supported devices are:
 	  Belkin F5U011
 	  Belkin F5U111
 	  CATC NetMate
 	  CATC NetMate II
 	  smartBridges smartNIC

 	  This driver makes the adapter appear as a normal Ethernet interface,
 	  typically on eth0, if it is the only ethernet device, or perhaps on
 	  eth1, if you have a PCI or ISA ethernet card installed.

 	  To compile this driver as a module, choose M here: the
 	  module will be called catc.

 config USB_KAWETH
 	tristate "USB KLSI KL5USB101-based ethernet device support"
 	---help---
 	  Say Y here if you want to use one of the following 10Mbps only
 	  USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
 	  3Com 3C19250
 	  ADS USB-10BT
 	  ATEN USB Ethernet
 	  ASANTE USB To Ethernet Adapter
 	  AOX Endpoints USB Ethernet
 	  Correga K.K.
 	  D-Link DSB-650C and DU-E10
 	  Entrega / Portgear E45
 	  I-O DATA USB-ET/T
 	  Jaton USB Ethernet Device Adapter
 	  Kingston Technology USB Ethernet Adapter
 	  Linksys USB10T
 	  Mobility USB-Ethernet Adapter
 	  NetGear EA-101
 	  Peracom Enet and Enet2
 	  Portsmith Express Ethernet Adapter
 	  Shark Pocket Adapter
 	  SMC 2202USB
 	  Sony Vaio port extender

 	  This driver is likely to work with most 10Mbps only USB Ethernet
 	  adapters, including some "no brand" devices. It does NOT work on
 	  SmartBridges smartNIC or on Belkin F5U111 devices - you should use
 	  the CATC NetMate driver for those. If you are not sure which one
 	  you need, select both, and the correct one should be selected for
 	  you.

 	  This driver makes the adapter appear as a normal Ethernet interface,
 	  typically on eth0, if it is the only ethernet device, or perhaps on
 	  eth1, if you have a PCI or ISA ethernet card installed.

 	  To compile this driver as a module, choose M here: the
 	  module will be called kaweth.

 config USB_PEGASUS
 	tristate "USB Pegasus/Pegasus-II based ethernet device support"
 	select MII
 	---help---
 	  Say Y here if you know you have Pegasus or Pegasus-II based adapter.
 	  If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
 	  complete list of supported devices.

 	  If your particular adapter is not in the list and you are _sure_ it
 	  is Pegasus or Pegasus II based then send me
 	  <petkan@users.sourceforge.net> vendor and device IDs.

 	  To compile this driver as a module, choose M here: the
 	  module will be called pegasus.

 config USB_RTL8150
 	tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
 	depends on EXPERIMENTAL
 	select MII
 	help
 	  Say Y here if you have RTL8150 based usb-ethernet adapter.
 	  Send me <petkan@users.sourceforge.net> any comments you may have.
 	  You can also check for updates at <http://pegasus2.sourceforge.net/>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called rtl8150.

 config USB_USBNET
 	tristate "Multi-purpose USB Networking Framework"
 	select MII
 	---help---
 	  This driver supports several kinds of network links over USB,
 	  with "minidrivers" built around a common network driver core
 	  that supports deep queues for efficient transfers.  (This gives
 	  better performance with small packets and at high speeds).

 	  The USB host runs "usbnet", and the other end of the link might be:

 	  - Another USB host, when using USB "network" or "data transfer"
 	    cables.  These are often used to network laptops to PCs, like
 	    "Laplink" parallel cables or some motherboards.  These rely
 	    on specialized chips from many suppliers.

 	  - An intelligent USB gadget, perhaps embedding a Linux system.
 	    These include PDAs running Linux (iPaq, Yopy, Zaurus, and
 	    others), and devices that interoperate using the standard
 	    CDC-Ethernet specification (including many cable modems).

 	  - Network adapter hardware (like those for 10/100 Ethernet) which
 	    uses this driver framework.

 	  The link will appear with a name like "usb0", when the link is
 	  a two-node link, or "eth0" for most CDC-Ethernet devices.  Those
 	  two-node links are most easily managed with Ethernet Bridging
 	  (CONFIG_BRIDGE) instead of routing.

 	  For more information see <http://www.linux-usb.org/usbnet/>.

 	  To compile this driver as a module, choose M here: the
 	  module will be called usbnet.

 config USB_NET_AX8817X
 	tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
 	depends on USB_USBNET
 	select CRC32
 	default y
 	help
 	  This option adds support for ASIX AX88xxx based USB 2.0
 	  10/100 Ethernet adapters.

  	  This driver should work with at least the following devices:
 	    * Aten UC210T
 	    * ASIX AX88172
 	    * Billionton Systems, USB2AR
 	    * Buffalo LUA-U2-KTX
 	    * Corega FEther USB2-TX
 	    * D-Link DUB-E100
 	    * Hawking UF200
 	    * Linksys USB200M
 	    * Netgear FA120
 	    * Sitecom LN-029
 	    * Intellinet USB 2.0 Ethernet
 	    * ST Lab USB 2.0 Ethernet
 	    * TrendNet TU2-ET100

 	  This driver creates an interface named "ethX", where X depends on
 	  what other networking devices you have in use.

 config USB_NET_CDCETHER
 	tristate "CDC Ethernet support (smart devices such as cable modems)"
 	depends on USB_USBNET
 	default y
 	help
 	  This option supports devices conforming to the Communication Device
 	  Class (CDC) Ethernet Control Model, a specification that's easy to
 	  implement in device firmware.  The CDC specifications are available
 	  from <http://www.usb.org/>.

 	  CDC Ethernet is an implementation option for DOCSIS cable modems
 	  that support USB connectivity, used for non-Microsoft USB hosts.
 	  The Linux-USB CDC Ethernet Gadget driver is an open implementation.
  	  This driver should work with at least the following devices:

 	    * Dell Wireless 5530 HSPA
  	    * Ericsson PipeRider (all variants)
 	    * Ericsson Mobile Broadband Module (all variants)
  	    * Motorola (DM100 and SB4100)
  	    * Broadcom Cable Modem (reference design)
 	    * Toshiba (PCX1100U and F3507g/F3607gw)
 	    * ...

 	  This driver creates an interface named "ethX", where X depends on
 	  what other networking devices you have in use.  However, if the
 	  IEEE 802 "local assignment" bit is set in the address, a "usbX"
 	  name is used instead.

 config USB_NET_CDC_EEM
 	tristate "CDC EEM support"
 	depends on USB_USBNET && EXPERIMENTAL
 	help
 	  This option supports devices conforming to the Communication Device
 	  Class (CDC) Ethernet Emulation Model, a specification that's easy to
 	  implement in device firmware.  The CDC EEM specifications are available
 	  from <http://www.usb.org/>.

 	  This driver creates an interface named "ethX", where X depends on
 	  what other networking devices you have in use.  However, if the
 	  IEEE 802 "local assignment" bit is set in the address, a "usbX"
 	  name is used instead.

 config USB_NET_CDC_NCM
 	tristate "CDC NCM support"
 	depends on USB_USBNET
 	default y
 	help
 	  This driver provides support for CDC NCM (Network Control Model
 	  Device USB Class Specification). The CDC NCM specification is
 	  available from <http://www.usb.org/>.

 	  Say "y" to link the driver statically, or "m" to build a
 	  dynamically linked module.

 	  This driver should work with at least the following devices:
 	    * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
 	    * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
 	    * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
 	    * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
 	    * Ericsson F5521gw Mobile Broadband Module

 config USB_NET_DM9601
 	tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
 	depends on USB_USBNET
 	select CRC32
 	help
 	  This option adds support for Davicom DM9601 based USB 1.1
 	  10/100 Ethernet adapters.

 config USB_NET_SMSC75XX
 	tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
 	depends on USB_USBNET
 	select CRC32
 	help
 	  This option adds support for SMSC LAN95XX based USB 2.0
 	  Gigabit Ethernet adapters.

 config USB_NET_SMSC95XX
 	tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
 	depends on USB_USBNET
 	select CRC32
 	help
 	  This option adds support for SMSC LAN95XX based USB 2.0
 	  10/100 Ethernet adapters.

 config USB_NET_GL620A
 	tristate "GeneSys GL620USB-A based cables"
 	depends on USB_USBNET
 	help
 	  Choose this option if you're using a host-to-host cable,
 	  or PC2PC motherboard, with this chip.

 	  Note that the half-duplex "GL620USB" is not supported.

 config USB_NET_NET1080
 	tristate "NetChip 1080 based cables (Laplink, ...)"
 	default y
 	depends on USB_USBNET
 	help
 	  Choose this option if you're using a host-to-host cable based
 	  on this design:  one NetChip 1080 chip and supporting logic,
 	  optionally with LEDs that indicate traffic

 config USB_NET_PLUSB
 	tristate "Prolific PL-2301/2302 based cables"
 	# if the handshake/init/reset problems, from original 'plusb',
 	# are ever resolved ... then remove "experimental"
 	depends on USB_USBNET && EXPERIMENTAL
 	help
 	  Choose this option if you're using a host-to-host cable
 	  with one of these chips.

 config USB_NET_MCS7830
 	tristate "MosChip MCS7830 based Ethernet adapters"
 	depends on USB_USBNET
 	help
 	  Choose this option if you're using a 10/100 Ethernet USB2
 	  adapter based on the MosChip 7830 controller. This includes
 	  adapters marketed under the DeLOCK brand.

 config USB_NET_RNDIS_HOST
 	tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
 	depends on USB_USBNET && EXPERIMENTAL
 	select USB_NET_CDCETHER
 	help
 	  This option enables hosting "Remote NDIS" USB networking links,
 	  as encouraged by Microsoft (instead of CDC Ethernet!) for use in
 	  various devices that may only support this protocol.  A variant
 	  of this protocol (with even less public documentation) seems to
 	  be at the root of Microsoft's "ActiveSync" too.

 	  Avoid using this protocol unless you have no better options.
 	  The protocol specification is incomplete, and is controlled by
 	  (and for) Microsoft; it isn't an "Open" ecosystem or market.

 config USB_NET_CDC_SUBSET
 	tristate "Simple USB Network Links (CDC Ethernet subset)"
 	depends on USB_USBNET
 	default y
 	help
 	  This driver module supports USB network devices that can work
 	  without any device-specific information.  Select it if you have
 	  one of these drivers.

 	  Note that while many USB host-to-host cables can work in this mode,
 	  that may mean not being able to talk to Win32 systems or more
 	  commonly not being able to handle certain events (like replugging
 	  the host on the other end) very well.  Also, these devices will
 	  not generally have permanently assigned Ethernet addresses.

 config USB_ALI_M5632
 	boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
 	depends on USB_NET_CDC_SUBSET
 	help
 	  Choose this option if you're using a host-to-host cable
 	  based on this design, which supports USB 2.0 high speed.

 config USB_AN2720
 	boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
 	depends on USB_NET_CDC_SUBSET
 	help
 	  Choose this option if you're using a host-to-host cable
 	  based on this design.  Note that AnchorChips is now a
 	  Cypress brand.

 config USB_BELKIN
 	boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
 	depends on USB_NET_CDC_SUBSET
 	default y
 	help
 	  Choose this option if you're using a host-to-host cable
 	  based on this design:  two NetChip 2890 chips and an Atmel
 	  microcontroller, with LEDs that indicate traffic.

 config USB_ARMLINUX
 	boolean "Embedded ARM Linux links (iPaq, ...)"
 	depends on USB_NET_CDC_SUBSET
 	default y
 	help
 	  Choose this option to support the "usb-eth" networking driver
 	  used by most of the ARM Linux community with device controllers
 	  such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
 	  in some PXA versions of the "blob" boot loader.

 	  Linux-based "Gumstix" PXA-25x based systems use this protocol
 	  to talk with other Linux systems.

 	  Although the ROMs shipped with Sharp Zaurus products use a
 	  different link level framing protocol, you can have them use
 	  this simpler protocol by installing a different kernel.

 config USB_EPSON2888
 	boolean "Epson 2888 based firmware (DEVELOPMENT)"
 	depends on USB_NET_CDC_SUBSET
 	help
 	  Choose this option to support the usb networking links used
 	  by some sample firmware from Epson.

 config USB_KC2190
 	boolean "KT Technology KC2190 based cables (InstaNet)"
 	depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
 	help
 	  Choose this option if you're using a host-to-host cable
 	  with one of these chips.

 config USB_NET_ZAURUS
 	tristate "Sharp Zaurus (stock ROMs) and compatible"
 	depends on USB_USBNET
 	select USB_NET_CDCETHER
 	select CRC32
 	default y
 	help
 	  Choose this option to support the usb networking links used by
 	  Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
 	  This also supports some related device firmware, as used in some
 	  PDAs from Olympus and some cell phones from Motorola.

 	  If you install an alternate image, such as the Linux 2.6 based
 	  versions of OpenZaurus, you should no longer need to support this
 	  protocol.  Only the "eth-fd" or "net_fd" drivers in these devices
 	  really need this non-conformant variant of CDC Ethernet (or in
 	  some cases CDC MDLM) protocol, not "g_ether".

 config USB_NET_CX82310_ETH
 	tristate "Conexant CX82310 USB ethernet port"
 	depends on USB_USBNET
 	help
 	  Choose this option if you're using a Conexant CX82310-based ADSL
 	  router with USB ethernet port. This driver is for routers only,
 	  it will not work with ADSL modems (use cxacru driver instead).

 config USB_HSO
 	tristate "Option USB High Speed Mobile Devices"
 	depends on USB && RFKILL
 	default n
 	help
 	  Choose this option if you have an Option HSDPA/HSUPA card.
 	  These cards support downlink speeds of 7.2Mbps or greater.

 	  To compile this driver as a module, choose M here: the
 	  module will be called hso.

 config USB_NET_INT51X1
 	tristate "Intellon PLC based usb adapter"
 	depends on USB_USBNET
 	help
 	  Choose this option if you're using a 14Mb USB-based PLC
 	  (Powerline Communications) solution with an Intellon
 	  INT51x1/INT5200 chip, like the "devolo dLan duo".

 config USB_CDC_PHONET
 	tristate "CDC Phonet support"
 	depends on PHONET
 	help
 	  Choose this option to support the Phonet interface to a Nokia
 	  cellular modem, as found on most Nokia handsets with the
 	  "PC suite" USB profile.

 config USB_IPHETH
 	tristate "Apple iPhone USB Ethernet driver"
 	default n
 	---help---
 	  Module used to share Internet connection (tethering) from your
 	  iPhone (Original, 3G and 3GS) to your system.
 	  Note that you need userspace libraries and programs that are needed
 	  to pair your device with your system and that understand the iPhone
 	  protocol.

 	  For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver

 config USB_SIERRA_NET
 	tristate "USB-to-WWAN Driver for Sierra Wireless modems"
 	depends on USB_USBNET
 	help
 	  Choose this option if you have a Sierra Wireless USB-to-WWAN device.

 	  To compile this driver as a module, choose M here: the
 	  module will be called sierra_net.

 endmenu
	#
	# USB Network devices configuration
	#
	comment "Networking support is needed for USB Network Adapter support"
	depends on USB && !NET

	menu "USB Network Adapters"
	depends on USB && NET

	config USB_CATC
	tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select CRC32
	---help---
	Say Y if you want to use one of the following 10Mbps USB Ethernet
	device based on the EL1210A chip. Supported devices are:
	Belkin F5U011
	Belkin F5U111
	CATC NetMate
	CATC NetMate II
	smartBridges smartNIC

	This driver makes the adapter appear as a normal Ethernet interface,
	typically on eth0, if it is the only ethernet device, or perhaps on
	eth1, if you have a PCI or ISA ethernet card installed.

	To compile this driver as a module, choose M here: the
	module will be called catc.

	config USB_KAWETH
	tristate "USB KLSI KL5USB101-based ethernet device support"
	---help---
	Say Y here if you want to use one of the following 10Mbps only
	USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
	3Com 3C19250
	ADS USB-10BT
	ATEN USB Ethernet
	ASANTE USB To Ethernet Adapter
	AOX Endpoints USB Ethernet
	Correga K.K.
	D-Link DSB-650C and DU-E10
	Entrega / Portgear E45
	I-O DATA USB-ET/T
	Jaton USB Ethernet Device Adapter
	Kingston Technology USB Ethernet Adapter
	Linksys USB10T
	Mobility USB-Ethernet Adapter
	NetGear EA-101
	Peracom Enet and Enet2
	Portsmith Express Ethernet Adapter
	Shark Pocket Adapter
	SMC 2202USB
	Sony Vaio port extender

	This driver is likely to work with most 10Mbps only USB Ethernet
	adapters, including some "no brand" devices. It does NOT work on
	SmartBridges smartNIC or on Belkin F5U111 devices - you should use
	the CATC NetMate driver for those. If you are not sure which one
	you need, select both, and the correct one should be selected for
	you.

	This driver makes the adapter appear as a normal Ethernet interface,
	typically on eth0, if it is the only ethernet device, or perhaps on
	eth1, if you have a PCI or ISA ethernet card installed.

	To compile this driver as a module, choose M here: the
	module will be called kaweth.

	config USB_PEGASUS
	tristate "USB Pegasus/Pegasus-II based ethernet device support"
	select MII
	---help---
	Say Y here if you know you have Pegasus or Pegasus-II based adapter.
	If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
	complete list of supported devices.

	If your particular adapter is not in the list and you are _sure_ it
	is Pegasus or Pegasus II based then send me
	<petkan@users.sourceforge.net> vendor and device IDs.

	To compile this driver as a module, choose M here: the
	module will be called pegasus.

	config USB_RTL8150
	tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select MII
	help
	Say Y here if you have RTL8150 based usb-ethernet adapter.
	Send me <petkan@users.sourceforge.net> any comments you may have.
	You can also check for updates at <http://pegasus2.sourceforge.net/>.

	To compile this driver as a module, choose M here: the
	module will be called rtl8150.

	config USB_USBNET
	tristate "Multi-purpose USB Networking Framework"
	select MII
	---help---
	This driver supports several kinds of network links over USB,
	with "minidrivers" built around a common network driver core
	that supports deep queues for efficient transfers. (This gives
	better performance with small packets and at high speeds).

	The USB host runs "usbnet", and the other end of the link might be:

	- Another USB host, when using USB "network" or "data transfer"
	cables. These are often used to network laptops to PCs, like
	"Laplink" parallel cables or some motherboards. These rely
	on specialized chips from many suppliers.

	- An intelligent USB gadget, perhaps embedding a Linux system.
	These include PDAs running Linux (iPaq, Yopy, Zaurus, and
	others), and devices that interoperate using the standard
	CDC-Ethernet specification (including many cable modems).

	- Network adapter hardware (like those for 10/100 Ethernet) which
	uses this driver framework.

	The link will appear with a name like "usb0", when the link is
	a two-node link, or "eth0" for most CDC-Ethernet devices. Those
	two-node links are most easily managed with Ethernet Bridging
	(CONFIG_BRIDGE) instead of routing.

	For more information see <http://www.linux-usb.org/usbnet/>.

	To compile this driver as a module, choose M here: the
	module will be called usbnet.

	config USB_NET_AX8817X
	tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
	depends on USB_USBNET
	select CRC32
	default y
	help
	This option adds support for ASIX AX88xxx based USB 2.0
	10/100 Ethernet adapters.

	This driver should work with at least the following devices:
	* Aten UC210T
	* ASIX AX88172
	* Billionton Systems, USB2AR
	* Buffalo LUA-U2-KTX
	* Corega FEther USB2-TX
	* D-Link DUB-E100
	* Hawking UF200
	* Linksys USB200M
	* Netgear FA120
	* Sitecom LN-029
	* Intellinet USB 2.0 Ethernet
	* ST Lab USB 2.0 Ethernet
	* TrendNet TU2-ET100

	This driver creates an interface named "ethX", where X depends on
	what other networking devices you have in use.

	config USB_NET_CDCETHER
	tristate "CDC Ethernet support (smart devices such as cable modems)"
	depends on USB_USBNET
	default y
	help
	This option supports devices conforming to the Communication Device
	Class (CDC) Ethernet Control Model, a specification that's easy to
	implement in device firmware. The CDC specifications are available
	from <http://www.usb.org/>.

	CDC Ethernet is an implementation option for DOCSIS cable modems
	that support USB connectivity, used for non-Microsoft USB hosts.
	The Linux-USB CDC Ethernet Gadget driver is an open implementation.
	This driver should work with at least the following devices:

	* Dell Wireless 5530 HSPA
	* Ericsson PipeRider (all variants)
	* Ericsson Mobile Broadband Module (all variants)
	* Motorola (DM100 and SB4100)
	* Broadcom Cable Modem (reference design)
	* Toshiba (PCX1100U and F3507g/F3607gw)
	* ...

	This driver creates an interface named "ethX", where X depends on
	what other networking devices you have in use. However, if the
	IEEE 802 "local assignment" bit is set in the address, a "usbX"
	name is used instead.

	config USB_NET_CDC_EEM
	tristate "CDC EEM support"
	depends on USB_USBNET && EXPERIMENTAL
	help
	This option supports devices conforming to the Communication Device
	Class (CDC) Ethernet Emulation Model, a specification that's easy to
	implement in device firmware. The CDC EEM specifications are available
	from <http://www.usb.org/>.

	This driver creates an interface named "ethX", where X depends on
	what other networking devices you have in use. However, if the
	IEEE 802 "local assignment" bit is set in the address, a "usbX"
	name is used instead.

	config USB_NET_CDC_NCM
	tristate "CDC NCM support"
	depends on USB_USBNET
	default y
	help
	This driver provides support for CDC NCM (Network Control Model
	Device USB Class Specification). The CDC NCM specification is
	available from <http://www.usb.org/>.

	Say "y" to link the driver statically, or "m" to build a
	dynamically linked module.

	This driver should work with at least the following devices:
	* ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
	* ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
	* ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
	* ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
	* Ericsson F5521gw Mobile Broadband Module

	config USB_NET_DM9601
	tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
	depends on USB_USBNET
	select CRC32
	help
	This option adds support for Davicom DM9601 based USB 1.1
	10/100 Ethernet adapters.

	config USB_NET_SMSC75XX
	tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
	depends on USB_USBNET
	select CRC32
	help
	This option adds support for SMSC LAN95XX based USB 2.0
	Gigabit Ethernet adapters.

	config USB_NET_SMSC95XX
	tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
	depends on USB_USBNET
	select CRC32
	help
	This option adds support for SMSC LAN95XX based USB 2.0
	10/100 Ethernet adapters.

	config USB_NET_GL620A
	tristate "GeneSys GL620USB-A based cables"
	depends on USB_USBNET
	help
	Choose this option if you're using a host-to-host cable,
	or PC2PC motherboard, with this chip.

	Note that the half-duplex "GL620USB" is not supported.

	config USB_NET_NET1080
	tristate "NetChip 1080 based cables (Laplink, ...)"
	default y
	depends on USB_USBNET
	help
	Choose this option if you're using a host-to-host cable based
	on this design: one NetChip 1080 chip and supporting logic,
	optionally with LEDs that indicate traffic

	config USB_NET_PLUSB
	tristate "Prolific PL-2301/2302 based cables"
	# if the handshake/init/reset problems, from original 'plusb',
	# are ever resolved ... then remove "experimental"
	depends on USB_USBNET && EXPERIMENTAL
	help
	Choose this option if you're using a host-to-host cable
	with one of these chips.

	config USB_NET_MCS7830
	tristate "MosChip MCS7830 based Ethernet adapters"
	depends on USB_USBNET
	help
	Choose this option if you're using a 10/100 Ethernet USB2
	adapter based on the MosChip 7830 controller. This includes
	adapters marketed under the DeLOCK brand.

	config USB_NET_RNDIS_HOST
	tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
	depends on USB_USBNET && EXPERIMENTAL
	select USB_NET_CDCETHER
	help
	This option enables hosting "Remote NDIS" USB networking links,
	as encouraged by Microsoft (instead of CDC Ethernet!) for use in
	various devices that may only support this protocol. A variant
	of this protocol (with even less public documentation) seems to
	be at the root of Microsoft's "ActiveSync" too.

	Avoid using this protocol unless you have no better options.
	The protocol specification is incomplete, and is controlled by
	(and for) Microsoft; it isn't an "Open" ecosystem or market.

	config USB_NET_CDC_SUBSET
	tristate "Simple USB Network Links (CDC Ethernet subset)"
	depends on USB_USBNET
	default y
	help
	This driver module supports USB network devices that can work
	without any device-specific information. Select it if you have
	one of these drivers.

	Note that while many USB host-to-host cables can work in this mode,
	that may mean not being able to talk to Win32 systems or more
	commonly not being able to handle certain events (like replugging
	the host on the other end) very well. Also, these devices will
	not generally have permanently assigned Ethernet addresses.

	config USB_ALI_M5632
	boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
	depends on USB_NET_CDC_SUBSET
	help
	Choose this option if you're using a host-to-host cable
	based on this design, which supports USB 2.0 high speed.

	config USB_AN2720
	boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
	depends on USB_NET_CDC_SUBSET
	help
	Choose this option if you're using a host-to-host cable
	based on this design. Note that AnchorChips is now a
	Cypress brand.

	config USB_BELKIN
	boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
	depends on USB_NET_CDC_SUBSET
	default y
	help
	Choose this option if you're using a host-to-host cable
	based on this design: two NetChip 2890 chips and an Atmel
	microcontroller, with LEDs that indicate traffic.

	config USB_ARMLINUX
	boolean "Embedded ARM Linux links (iPaq, ...)"
	depends on USB_NET_CDC_SUBSET
	default y
	help
	Choose this option to support the "usb-eth" networking driver
	used by most of the ARM Linux community with device controllers
	such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
	in some PXA versions of the "blob" boot loader.

	Linux-based "Gumstix" PXA-25x based systems use this protocol
	to talk with other Linux systems.

	Although the ROMs shipped with Sharp Zaurus products use a
	different link level framing protocol, you can have them use
	this simpler protocol by installing a different kernel.

	config USB_EPSON2888
	boolean "Epson 2888 based firmware (DEVELOPMENT)"
	depends on USB_NET_CDC_SUBSET
	help
	Choose this option to support the usb networking links used
	by some sample firmware from Epson.

	config USB_KC2190
	boolean "KT Technology KC2190 based cables (InstaNet)"
	depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
	help
	Choose this option if you're using a host-to-host cable
	with one of these chips.

	config USB_NET_ZAURUS
	tristate "Sharp Zaurus (stock ROMs) and compatible"
	depends on USB_USBNET
	select USB_NET_CDCETHER
	select CRC32
	default y
	help
	Choose this option to support the usb networking links used by
	Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
	This also supports some related device firmware, as used in some
	PDAs from Olympus and some cell phones from Motorola.

	If you install an alternate image, such as the Linux 2.6 based
	versions of OpenZaurus, you should no longer need to support this
	protocol. Only the "eth-fd" or "net_fd" drivers in these devices
	really need this non-conformant variant of CDC Ethernet (or in
	some cases CDC MDLM) protocol, not "g_ether".

	config USB_NET_CX82310_ETH
	tristate "Conexant CX82310 USB ethernet port"
	depends on USB_USBNET
	help
	Choose this option if you're using a Conexant CX82310-based ADSL
	router with USB ethernet port. This driver is for routers only,
	it will not work with ADSL modems (use cxacru driver instead).

	config USB_HSO
	tristate "Option USB High Speed Mobile Devices"
	depends on USB && RFKILL
	default n
	help
	Choose this option if you have an Option HSDPA/HSUPA card.
	These cards support downlink speeds of 7.2Mbps or greater.

	To compile this driver as a module, choose M here: the
	module will be called hso.

	config USB_NET_INT51X1
	tristate "Intellon PLC based usb adapter"
	depends on USB_USBNET
	help
	Choose this option if you're using a 14Mb USB-based PLC
	(Powerline Communications) solution with an Intellon
	INT51x1/INT5200 chip, like the "devolo dLan duo".

	config USB_CDC_PHONET
	tristate "CDC Phonet support"
	depends on PHONET
	help
	Choose this option to support the Phonet interface to a Nokia
	cellular modem, as found on most Nokia handsets with the
	"PC suite" USB profile.

	config USB_IPHETH
	tristate "Apple iPhone USB Ethernet driver"
	default n
	---help---
	Module used to share Internet connection (tethering) from your
	iPhone (Original, 3G and 3GS) to your system.
	Note that you need userspace libraries and programs that are needed
	to pair your device with your system and that understand the iPhone
	protocol.

	For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver

	config USB_SIERRA_NET
	tristate "USB-to-WWAN Driver for Sierra Wireless modems"
	depends on USB_USBNET
	help
	Choose this option if you have a Sierra Wireless USB-to-WWAN device.

	To compile this driver as a module, choose M here: the
	module will be called sierra_net.

	endmenu