| /* Copyright (c) 2014-2015, 2020, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &spmi_bus { |
| |
| pm8909_0: qcom,pm8909@0 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x0 0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8909_revid: qcom,revid@100 { |
| compatible = "qcom,qpnp-revid"; |
| reg = <0x100 0x100>; |
| }; |
| |
| pm8909_pon: qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| interrupts = <0x0 0x8 0x0 0x0>, |
| <0x0 0x8 0x1 0x0>; |
| interrupt-names = "kpdpwr", "resin"; |
| qcom,pon-dbc-delay = <15625>; |
| qcom,kpdpwr-sw-debounce; |
| qcom,system-reset; |
| qcom,store-hard-reset-reason; |
| |
| qcom,pon_1 { |
| qcom,pon-type = <0>; |
| qcom,pull-up = <1>; |
| qcom,s1-timer = <10256>; |
| qcom,s2-timer = <2000>; |
| qcom,s2-type = <1>; |
| linux,code = <116>; |
| }; |
| |
| qcom,pon_2 { |
| qcom,pon-type = <1>; |
| qcom,pull-up = <1>; |
| linux,code = <114>; |
| }; |
| }; |
| |
| pm8909_mpps: mpps { |
| compatible = "qcom,spmi-mpp"; |
| reg = <0xa000 0x400>; |
| interrupts = <0x0 0xa0 0 IRQ_TYPE_NONE>, |
| <0x0 0xa1 0 IRQ_TYPE_NONE>, |
| <0x0 0xa2 0 IRQ_TYPE_NONE>, |
| <0x0 0xa3 0 IRQ_TYPE_NONE>; |
| interrupt-names = "pm8909_mpp1", "pm8909_mpp2", |
| "pm8909_mpp3", "pm8909_mpp4"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| pm8909_gpios: gpios { |
| compatible = "qcom,spmi-gpio"; |
| reg = <0xc000 0x400>; |
| interrupts = <0x0 0xc1 0 IRQ_TYPE_NONE>, |
| <0x0 0xc3 0 IRQ_TYPE_NONE>; |
| interrupt-names = "pm8909_gpio2", "pm8909_gpio4"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| qcom,gpios-disallowed = <1 3>; |
| }; |
| |
| pm8909_vadc: vadc@3100 { |
| compatible = "qcom,qpnp-vadc"; |
| reg = <0x3100 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "eoc-int-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1800>; |
| qcom,vadc-poll-eoc; |
| qcom,pmic-revid = <&pm8909_revid>; |
| |
| chan@8 { |
| label = "die_temp"; |
| reg = <8>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <3>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@9 { |
| label = "ref_625mv"; |
| reg = <9>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@a { |
| label = "ref_1250v"; |
| reg = <0xa>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| }; |
| |
| pm8909_adc_tm: vadc@3400 { |
| compatible = "qcom,qpnp-adc-tm"; |
| reg = <0x3400 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x34 0x3 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x34 0x4 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "eoc-int-en-set", |
| "high-thr-en-set", |
| "low-thr-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1800>; |
| qcom,adc_tm-vadc = <&pm8909_vadc>; |
| }; |
| |
| pm8909_rtc: qcom,pm8909_rtc { |
| spmi-dev-container; |
| compatible = "qcom,qpnp-rtc"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| qcom,qpnp-rtc-write = <0>; |
| qcom,qpnp-rtc-alarm-pwrup = <0>; |
| |
| qcom,pm8909_rtc_rw@6000 { |
| reg = <0x6000 0x100>; |
| }; |
| qcom,pm8909_rtc_alarm@6100 { |
| reg = <0x6100 0x100>; |
| interrupts = <0x0 0x61 0x1 0x0>; |
| }; |
| }; |
| |
| qcom,leds@a300 { |
| compatible = "qcom,leds-qpnp"; |
| reg = <0xa300 0x100>; |
| label = "mpp"; |
| }; |
| |
| pm8909_chg: qcom,charger { |
| spmi-dev-container; |
| compatible = "qcom,qpnp-linear-charger"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qcom,vddmax-mv = <4200>; |
| qcom,vddsafe-mv = <4200>; |
| qcom,vinmin-mv = <4308>; |
| qcom,ibatsafe-ma = <1440>; |
| qcom,thermal-mitigation = <1440 720 630 0>; |
| qcom,cool-bat-decidegc = <100>; |
| qcom,warm-bat-decidegc = <450>; |
| qcom,cool-bat-mv = <4100>; |
| qcom,warm-bat-mv = <4100>; |
| qcom,ibatmax-warm-ma = <360>; |
| qcom,ibatmax-cool-ma = <360>; |
| qcom,batt-hot-percentage = <25>; |
| qcom,batt-cold-percentage = <80>; |
| qcom,tchg-mins = <232>; |
| qcom,chg-vadc = <&pm8909_vadc>; |
| qcom,chg-adc_tm = <&pm8909_adc_tm>; |
| #cooling-cells = <2>; |
| |
| status = "okay"; |
| |
| qcom,chgr@1000 { |
| reg = <0x1000 0x100>; |
| interrupts = <0x0 0x10 0x7 0x1>, |
| <0x0 0x10 0x6 0x1>, |
| <0x0 0x10 0x5 0x3>, |
| <0x0 0x10 0x0 0x2>; |
| interrupt-names = "chg-done", |
| "chg-failed", |
| "fast-chg-on", |
| "vbat-det-lo"; |
| }; |
| |
| qcom,bat-if@1200 { |
| reg = <0x1200 0x100>; |
| interrupts = <0x0 0x12 0x1 0x3>, |
| <0x0 0x12 0x0 0x3>; |
| interrupt-names = "bat-temp-ok", |
| "batt-pres"; |
| }; |
| |
| qcom,usb-chgpth@1300 { |
| reg = <0x1300 0x100>; |
| interrupts = <0 0x13 0x4 0x3>, |
| <0 0x13 0x2 0x1>, |
| <0 0x13 0x1 0x3>; |
| interrupt-names = "usb-over-temp", |
| "chg-gone", |
| "usbin-valid"; |
| }; |
| |
| qcom,chg-misc@1600 { |
| reg = <0x1600 0x100>; |
| }; |
| }; |
| |
| pm8909_tz: qcom,temp-alarm@2400 { |
| compatible = "qcom,qpnp-temp-alarm"; |
| reg = <0x2400 0x100>; |
| interrupts = <0x0 0x24 0x0 0x1>; |
| label = "pm8909_tz"; |
| qcom,channel-num = <8>; |
| qcom,threshold-set = <0>; |
| qcom,temp_alarm-vadc = <&pm8909_vadc>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8909_bms: qcom,vmbms { |
| spmi-dev-container; |
| compatible = "qcom,qpnp-vm-bms"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| status = "disabled"; |
| |
| qcom,v-cutoff-uv = <3400000>; |
| qcom,max-voltage-uv = <4200000>; |
| qcom,r-conn-mohm = <0>; |
| qcom,shutdown-soc-valid-limit = <100>; |
| qcom,low-soc-calculate-soc-threshold = <15>; |
| qcom,low-voltage-calculate-soc-ms = <1000>; |
| qcom,low-soc-calculate-soc-ms = <5000>; |
| qcom,calculate-soc-ms = <20000>; |
| qcom,volatge-soc-timeout-ms = <60000>; |
| qcom,low-voltage-threshold = <3450000>; |
| qcom,s3-ocv-tolerence-uv = <1200>; |
| qcom,s2-fifo-length = <5>; |
| qcom,low-soc-fifo-length = <2>; |
| qcom,bms-vadc = <&pm8909_vadc>; |
| qcom,bms-adc_tm = <&pm8909_adc_tm>; |
| qcom,pmic-revid = <&pm8909_revid>; |
| |
| qcom,force-s3-on-suspend; |
| qcom,force-s2-in-charging; |
| qcom,report-charger-eoc; |
| qcom,resume-soc = <99>; |
| |
| qcom,batt-pres-status@1208 { |
| reg = <0x1208 0x1>; |
| }; |
| |
| qcom,qpnp-chg-pres@1008 { |
| reg = <0x1008 0x1>; |
| }; |
| |
| qcom,vm-bms@4000 { |
| reg = <0x4000 0x100>; |
| interrupts = <0x0 0x40 0x0 0x0>, |
| <0x0 0x40 0x3 0x0>, |
| <0x0 0x40 0x4 0x0>, |
| <0x0 0x40 0x5 0x0>; |
| |
| interrupt-names = "leave_cv", |
| "ocv_thr", |
| "fifo_update_done", |
| "fsm_state_change"; |
| }; |
| }; |
| }; |
| |
| pm8909_1: qcom,pm8909@1 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x1 0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| regulator@1400 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_s1"; |
| spmi-dev-container; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x1400 0x300>; |
| status = "disabled"; |
| |
| qcom,ctl@1400 { |
| reg = <0x1400 0x100>; |
| }; |
| qcom,ps@1500 { |
| reg = <0x1500 0x100>; |
| }; |
| qcom,freq@1600 { |
| reg = <0x1600 0x100>; |
| }; |
| }; |
| |
| regulator@1700 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_s2"; |
| spmi-dev-container; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x1700 0x300>; |
| status = "disabled"; |
| |
| qcom,ctl@1700 { |
| reg = <0x1700 0x100>; |
| }; |
| qcom,ps@1800 { |
| reg = <0x1800 0x100>; |
| }; |
| qcom,freq@1900 { |
| reg = <0x1900 0x100>; |
| }; |
| }; |
| |
| regulator@4000 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l1"; |
| reg = <0x4000 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4100 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l2"; |
| reg = <0x4100 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4200 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l3"; |
| reg = <0x4200 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4300 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l4"; |
| reg = <0x4300 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4400 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l5"; |
| reg = <0x4400 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4500 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l6"; |
| reg = <0x4500 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4600 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l7"; |
| reg = <0x4600 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4700 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l8"; |
| reg = <0x4700 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4800 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l9"; |
| reg = <0x4800 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4900 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l10"; |
| reg = <0x4900 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4a00 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l11"; |
| reg = <0x4a00 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4b00 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l12"; |
| reg = <0x4b00 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4c00 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l13"; |
| reg = <0x4c00 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4d00 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l14"; |
| reg = <0x4d00 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@4e00 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l15"; |
| reg = <0x4e00 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@5000 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l17"; |
| reg = <0x5000 0x100>; |
| status = "disabled"; |
| }; |
| |
| regulator@5100 { |
| compatible = "qcom,qpnp-regulator"; |
| regulator-name = "8909_l18"; |
| reg = <0x5100 0x100>; |
| status = "disabled"; |
| }; |
| |
| pm8909_vib: qcom,vibrator@c000 { |
| compatible = "qcom,qpnp-vibrator"; |
| reg = <0xc000 0x100>; |
| label = "vibrator"; |
| status = "disabled"; |
| }; |
| |
| pm8909_conga_dig: 8909_wcd_codec@f000 { |
| compatible = "qcom,msm8x16_wcd_codec"; |
| reg = <0xf000 0x100>; |
| interrupt-parent = <&spmi_bus>; |
| interrupts = <0x1 0xf0 0x0 0x0>, |
| <0x1 0xf0 0x1 0x0>, |
| <0x1 0xf0 0x2 0x0>, |
| <0x1 0xf0 0x3 0x0>, |
| <0x1 0xf0 0x4 0x0>, |
| <0x1 0xf0 0x5 0x0>, |
| <0x1 0xf0 0x6 0x0>, |
| <0x1 0xf0 0x7 0x0>; |
| interrupt-names = "spk_cnp_int", |
| "spk_clip_int", |
| "spk_ocp_int", |
| "ins_rem_det1", |
| "but_rel_det", |
| "but_press_det", |
| "ins_rem_det", |
| "mbhc_int"; |
| |
| cdc-vdda-cp-supply = <&pm8909_s2>; |
| qcom,cdc-vdda-cp-voltage = <1800000 2200000>; |
| qcom,cdc-vdda-cp-current = <500000>; |
| |
| cdc-vdda-h-supply = <&pm8909_l5>; |
| qcom,cdc-vdda-h-voltage = <1800000 1800000>; |
| qcom,cdc-vdda-h-current = <10000>; |
| |
| cdc-vdd-px-supply = <&pm8909_l5>; |
| qcom,cdc-vdd-px-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-px-current = <5000>; |
| |
| cdc-vdd-pa-supply = <&pm8909_s2>; |
| qcom,cdc-vdd-pa-voltage = <1800000 2200000>; |
| qcom,cdc-vdd-pa-current = <260000>; |
| |
| cdc-vdd-mic-bias-supply = <&pm8909_l13>; |
| qcom,cdc-vdd-mic-bias-voltage = <3075000 3075000>; |
| qcom,cdc-vdd-mic-bias-current = <5000>; |
| |
| qcom,cdc-mclk-clk-rate = <9600000>; |
| |
| qcom,cdc-static-supplies = "cdc-vdda-h", |
| "cdc-vdd-px", |
| "cdc-vdd-pa", |
| "cdc-vdda-cp"; |
| |
| qcom,cdc-on-demand-supplies = "cdc-vdd-mic-bias"; |
| }; |
| |
| pm8909_conga_analog: 8909_wcd_codec@f100 { |
| compatible = "qcom,msm8x16_wcd_codec"; |
| reg = <0xf100 0x100>; |
| interrupt-parent = <&spmi_bus>; |
| interrupts = <0x1 0xf1 0x0 0x0>, |
| <0x1 0xf1 0x1 0x0>, |
| <0x1 0xf1 0x2 0x0>, |
| <0x1 0xf1 0x3 0x0>, |
| <0x1 0xf1 0x4 0x0>, |
| <0x1 0xf1 0x5 0x0>; |
| interrupt-names = "ear_ocp_int", |
| "hphr_ocp_int", |
| "hphl_ocp_det", |
| "ear_cnp_int", |
| "hphr_cnp_int", |
| "hphl_cnp_int"; |
| }; |
| |
| pm8909_pwm: pwm@bc00 { |
| compatible = "qcom,qpnp-pwm"; |
| reg = <0xbc00 0x100>; |
| reg-names = "qpnp-lpg-channel-base"; |
| qcom,channel-id = <0>; |
| qcom,supported-sizes = <6>, <9>; |
| #pwm-cells = <2>; |
| }; |
| }; |
| }; |
| |
| &thermal_zones { |
| pm8909_temp_alarm: pm8909_tz { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8909_tz>; |
| wake-capable-sensor; |
| |
| trips { |
| pm8909_trip0: pm8909-trip0 { |
| temperature = <105000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| pm8909_trip1: pm8909-trip1 { |
| temperature = <125000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| pm8909_trip2: pm8909-trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |