| /* Copyright (c) 2015-2017, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &spmi_bus { |
| qcom,pm8950@0 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8950_revid: qcom,revid@100 { |
| compatible = "qcom,qpnp-revid"; |
| reg = <0x100 0x100>; |
| }; |
| |
| pm8950_temp_alarm: qcom,temp-alarm@2400 { |
| compatible = "qcom,qpnp-temp-alarm"; |
| reg = <0x2400 0x100>; |
| interrupts = <0x0 0x24 0x0>; |
| label = "pm8950_tz"; |
| qcom,channel-num = <8>; |
| qcom,threshold-set = <0>; |
| qcom,temp_alarm-vadc = <&pm8950_vadc>; |
| }; |
| |
| qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| interrupts = <0x0 0x8 0x0>, |
| <0x0 0x8 0x1>, |
| <0x0 0x8 0x4>, |
| <0x0 0x8 0x5>; |
| interrupt-names = "kpdpwr", "resin", |
| "resin-bark", "kpdpwr-resin-bark"; |
| qcom,pon-dbc-delay = <15625>; |
| qcom,system-reset; |
| |
| qcom,pon_1 { |
| qcom,pon-type = <0>; |
| qcom,pull-up = <1>; |
| linux,code = <116>; |
| }; |
| |
| qcom,pon_2 { |
| qcom,pon-type = <1>; |
| qcom,pull-up = <1>; |
| linux,code = <114>; |
| }; |
| }; |
| |
| pm8950_coincell: qcom,coincell@2800 { |
| compatible = "qcom,qpnp-coincell"; |
| reg = <0x2800 0x100>; |
| }; |
| |
| pm8950_mpps: mpps { |
| compatible = "qcom,qpnp-pin"; |
| spmi-dev-container; |
| gpio-controller; |
| #gpio-cells = <2>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| label = "pm8950-mpp"; |
| |
| mpp@a000 { |
| reg = <0xa000 0x100>; |
| qcom,pin-num = <1>; |
| status = "disabled"; |
| }; |
| |
| mpp@a100 { |
| /* MPP2 - PA_THERM config */ |
| reg = <0xa100 0x100>; |
| qcom,pin-num = <2>; |
| qcom,mode = <4>; /* AIN input */ |
| qcom,invert = <1>; /* Enable MPP */ |
| qcom,ain-route = <1>; /* AMUX 6 */ |
| qcom,master-en = <1>; |
| qcom,src-sel = <0>; /* Function constant */ |
| }; |
| |
| mpp@a200 { |
| reg = <0xa200 0x100>; |
| qcom,pin-num = <3>; |
| status = "disabled"; |
| }; |
| |
| mpp@a300 { |
| /* MPP4 - CASE_THERM config */ |
| reg = <0xa300 0x100>; |
| qcom,pin-num = <4>; |
| qcom,mode = <4>; /* AIN input */ |
| qcom,invert = <1>; /* Enable MPP */ |
| qcom,ain-route = <3>; /* AMUX 8 */ |
| qcom,master-en = <1>; |
| qcom,src-sel = <0>; /* Function constant */ |
| }; |
| }; |
| |
| pm8950_gpios: gpios { |
| spmi-dev-container; |
| compatible = "qcom,qpnp-pin"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| label = "pm8950-gpio"; |
| |
| gpio@c000 { |
| reg = <0xc000 0x100>; |
| qcom,pin-num = <1>; |
| status = "disabled"; |
| }; |
| |
| gpio@c100 { |
| reg = <0xc100 0x100>; |
| qcom,pin-num = <2>; |
| status = "disabled"; |
| }; |
| |
| gpio@c200 { |
| reg = <0xc200 0x100>; |
| qcom,pin-num = <3>; |
| status = "disabled"; |
| }; |
| |
| gpio@c300 { |
| reg = <0xc300 0x100>; |
| qcom,pin-num = <4>; |
| status = "disabled"; |
| }; |
| |
| gpio@c400 { |
| reg = <0xc400 0x100>; |
| qcom,pin-num = <5>; |
| status = "disabled"; |
| }; |
| |
| gpio@c500 { |
| reg = <0xc500 0x100>; |
| qcom,pin-num = <6>; |
| status = "disabled"; |
| }; |
| |
| gpio@c600 { |
| reg = <0xc600 0x100>; |
| qcom,pin-num = <7>; |
| status = "disabled"; |
| }; |
| |
| gpio@c700 { |
| reg = <0xc700 0x100>; |
| qcom,pin-num = <8>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pm8950_vadc: vadc@3100 { |
| compatible = "qcom,qpnp-vadc"; |
| reg = <0x3100 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x31 0x0>; |
| interrupt-names = "eoc-int-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1800>; |
| qcom,vadc-poll-eoc; |
| qcom,pmic-revid = <&pm8950_revid>; |
| |
| chan@5 { |
| label = "vcoin"; |
| reg = <5>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@7 { |
| label = "vph_pwr"; |
| reg = <7>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@8 { |
| label = "die_temp"; |
| reg = <8>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <3>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@9 { |
| label = "ref_625mv"; |
| reg = <9>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@a { |
| label = "ref_1250v"; |
| reg = <0xa>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@c { |
| label = "ref_buf_625mv"; |
| reg = <0xc>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@36 { |
| label = "pa_therm0"; |
| reg = <0x36>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@11 { |
| label = "pa_therm1"; |
| reg = <0x11>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@32 { |
| label = "xo_therm"; |
| reg = <0x32>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <4>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@3c { |
| label = "xo_therm_buf"; |
| reg = <0x3c>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <4>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@13 { |
| label = "case_therm"; |
| reg = <0x13>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| }; |
| |
| pm8950_adc_tm: vadc@3400 { |
| compatible = "qcom,qpnp-adc-tm"; |
| reg = <0x3400 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x34 0x0>, |
| <0x0 0x34 0x3>, |
| <0x0 0x34 0x4>; |
| interrupt-names = "eoc-int-en-set", |
| "high-thr-en-set", |
| "low-thr-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1800>; |
| qcom,adc_tm-vadc = <&pm8950_vadc>; |
| qcom,pmic-revid = <&pm8950_revid>; |
| |
| chan@36 { |
| label = "pa_therm0"; |
| reg = <0x36>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,btm-channel-number = <0x48>; |
| qcom,thermal-node; |
| }; |
| |
| chan@7 { |
| label = "vph_pwr"; |
| reg = <0x7>; |
| qcom,decimation = <0>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| qcom,btm-channel-number = <0x68>; |
| }; |
| }; |
| |
| pm8950_rtc: qcom,pm8950_rtc { |
| spmi-dev-container; |
| compatible = "qcom,qpnp-rtc"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| qcom,qpnp-rtc-write = <0>; |
| qcom,qpnp-rtc-alarm-pwrup = <0>; |
| |
| qcom,pm8950_rtc_rw@6000 { |
| reg = <0x6000 0x100>; |
| }; |
| |
| qcom,pm8950_rtc_alarm@6100 { |
| reg = <0x6100 0x100>; |
| interrupts = <0x0 0x61 0x1>; |
| }; |
| }; |
| |
| qcom,leds@a300 { |
| compatible = "qcom,leds-qpnp"; |
| reg = <0xa300 0x100>; |
| label = "mpp"; |
| }; |
| }; |
| |
| pm8950_1: qcom,pm8950@1 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8950_pwm: pwm@bc00 { |
| status = "disabled"; |
| compatible = "qcom,qpnp-pwm"; |
| reg = <0xbc00 0x100>; |
| reg-names = "qpnp-lpg-channel-base"; |
| qcom,channel-id = <0>; |
| qcom,supported-sizes = <6>, <9>; |
| #pwm-cells = <2>; |
| }; |
| }; |
| }; |