| /* |
| * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &blsp1_uart2 { |
| status = "ok"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart_console_active>; |
| }; |
| |
| #include <dt-bindings/clock/msm-clocks-8952.h> |
| #include "qm215-camera-sensor-qrd.dtsi" |
| |
| &pm8916_chg{ |
| status = "ok"; |
| qcom,chgr-led-support; |
| qcom,vddmax-mv = <4400>; |
| qcom,vddsafe-mv = <4400>; |
| qcom,batt-hot-percentage = <35>; |
| }; |
| |
| &pm8916_bms{ |
| status = "ok"; |
| qcom,battery-data = <&qrd_batterydata>; |
| qcom,batt-aging-comp; |
| qcom,resume-soc = <99>; |
| }; |
| |
| &pm8916_vib{ |
| status = "ok"; |
| }; |
| |
| &soc { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| input-name = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_key_active>; |
| |
| vol_up { |
| label = "volume_up"; |
| gpios = <&tlmm 91 0x1>; |
| linux,input-type = <1>; |
| linux,code = <115>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| gpio-key,wakeup; |
| }; |
| }; |
| |
| fpc1020 { |
| compatible = "fpc,fpc1020"; |
| interrupt-parent = <&tlmm>; |
| interrupts = <48 0>; |
| fpc,gpio_rst = <&tlmm 124 0x0>; |
| fpc,gpio_irq = <&tlmm 48 0>; |
| vcc_spi-supply = <&pm8916_l5>; |
| vdd_io-supply = <&pm8916_l5>; |
| vdd_ana-supply = <&pm8916_l5>; |
| fpc,enable-on-boot; |
| pinctrl-names = "fpc1020_reset_reset", |
| "fpc1020_reset_active", |
| "fpc1020_irq_active"; |
| pinctrl-0 = <&fpc_reset_low>; |
| pinctrl-1 = <&fpc_reset_high>; |
| pinctrl-2 = <&fpc_int_low>; |
| }; |
| }; |
| |
| &sdhc_1 { |
| /* device core power supply */ |
| vdd-supply = <&pm8916_l8>; |
| qcom,vdd-voltage-level = <2900000 2900000>; |
| qcom,vdd-current-level = <200 400000>; |
| |
| /* |
| * device communication power is an external |
| * regulator eLDO3, which is enabled via L5A |
| */ |
| vdd-io-supply = <&pm8916_l5>; |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-lpm-sup; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <200 325000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>; |
| |
| qcom,clk-rates = <400000 20000000 25000000 50000000 100000000 192000000 |
| 384000000>; |
| qcom,nonremovable; |
| qcom,bus-speed-mode = "HS400_1p8v", "HS200_1p8v", "DDR_1p8v"; |
| |
| status = "ok"; |
| }; |
| |
| &sdhc_2 { |
| /* device core power supply */ |
| vdd-supply = <&pm8916_l11>; |
| qcom,vdd-voltage-level = <2950000 2950000>; |
| qcom,vdd-current-level = <15000 800000>; |
| |
| /* device communication power supply */ |
| vdd-io-supply = <&pm8916_l12>; |
| qcom,vdd-io-voltage-level = <1800000 2950000>; |
| qcom,vdd-io-current-level = <200 22000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; |
| |
| cd-gpios = <&tlmm 67 0x0>; |
| |
| qcom,clk-rates = <400000 20000000 25000000 50000000 100000000 |
| 200000000>; |
| qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50", "DDR50", "SDR104"; |
| status = "ok"; |
| }; |
| |
| &mdss_dsi_active { |
| mux { |
| pins = "gpio60", "gpio93", "gpio94"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio60", "gpio93", "gpio94"; |
| drive-strength = <8>; /* 8 mA */ |
| bias-disable = <0>; /* no pull */ |
| output-high; |
| }; |
| }; |
| |
| &mdss_dsi_suspend { |
| mux { |
| pins = "gpio60", "gpio93", "gpio94"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio60", "gpio93", "gpio94"; |
| drive-strength = <2>; /* 2 mA */ |
| bias-pull-down; /* pull down */ |
| }; |
| }; |
| |
| #include "msm8937-mdss-panels.dtsi" |
| |
| &mdss_mdp { |
| qcom,mdss-pref-prim-intf = "dsi"; |
| }; |
| |
| &dsi_panel_pwr_supply { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| qcom,panel-supply-entry@0 { |
| reg = <1>; |
| qcom,supply-name = "vddio"; |
| qcom,supply-min-voltage = <1744000>; |
| qcom,supply-max-voltage = <1904000>; |
| qcom,supply-enable-load = <100000>; |
| qcom,supply-disable-load = <100>; |
| }; |
| /delete-node/ qcom,panel-supply-entry@1; |
| /delete-node/ qcom,panel-supply-entry@2; |
| /delete-node/ qcom,panel-supply-entry@3; |
| }; |
| |
| &pm8916_gpios { |
| nfc_clk { |
| nfc_clk_default: nfc_clk_default { |
| pins = "gpio2"; |
| function = "normal"; |
| input-enable; |
| power-source = <1>; |
| }; |
| }; |
| }; |
| |
| &i2c_5 { /* BLSP2 QUP1 (NFC) */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "ok"; |
| nq@28 { |
| compatible = "qcom,nq-nci"; |
| reg = <0x28>; |
| qcom,nq-irq = <&tlmm 17 0x00>; |
| qcom,nq-ven = <&tlmm 16 0x00>; |
| qcom,nq-firm = <&tlmm 130 0x00>; |
| qcom,nq-clkreq = <&pm8916_gpios 2 0x00>; |
| interrupt-parent = <&tlmm>; |
| qcom,clk-src = "BBCLK2"; |
| interrupts = <17 0>; |
| interrupt-names = "nfc_irq"; |
| pinctrl-names = "nfc_active", "nfc_suspend"; |
| pinctrl-0 = <&nfc_int_active &nfc_disable_active |
| &nfc_clk_default>; |
| pinctrl-1 = <&nfc_int_suspend &nfc_disable_suspend>; |
| clocks = <&clock_gcc clk_bb_clk2_pin>; |
| clock-names = "ref_clk"; |
| }; |
| }; |
| |
| &mdss_dsi { |
| hw-config = "single_dsi"; |
| }; |
| |
| &mdss_dsi0 { |
| qcom,dsi-pref-prim-pan = <&dsi_hx8399c_hd_vid>; |
| pinctrl-names = "mdss_default", "mdss_sleep"; |
| pinctrl-0 = <&mdss_dsi_active &mdss_te_active>; |
| pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>; |
| |
| qcom,platform-te-gpio = <&tlmm 24 0>; |
| qcom,platform-reset-gpio = <&tlmm 60 0>; |
| qcom,platform-bklight-en-gpio = <&tlmm 93 0>; |
| qcom,platform-enable-gpio = <&tlmm 94 0>; |
| }; |
| |
| &dsi_hx8399c_hd_vid { |
| qcom,mdss-dsi-panel-timings = |
| [e7 1c 12 00 42 42 18 20 17 03 04 00]; |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_pwm"; |
| qcom,mdss-dsi-bl-pmic-pwm-frequency = <100>; |
| qcom,mdss-dsi-bl-pmic-bank-select = <0>; |
| qcom,mdss-dsi-pwm-gpio = <&pm8916_mpps 4 0>; |
| qcom,esd-check-enabled; |
| qcom,mdss-dsi-panel-status-check-mode = "reg_read"; |
| qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a]; |
| qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode"; |
| qcom,mdss-dsi-panel-status-value = <0x9d 0x9d 0x9d 0x9d>; |
| qcom,mdss-dsi-panel-on-check-value = <0x9d 0x9d 0x9d 0x9d>; |
| qcom,mdss-dsi-panel-status-read-length = <4>; |
| qcom,mdss-dsi-panel-max-error-count = <3>; |
| qcom,mdss-dsi-min-refresh-rate = <48>; |
| qcom,mdss-dsi-max-refresh-rate = <60>; |
| qcom,mdss-dsi-pan-enable-dynamic-fps; |
| qcom,mdss-dsi-pan-fps-update = |
| "dfps_immediate_porch_mode_vfp"; |
| }; |