| /* Copyright (c) 2018, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include "sdm845-qvr.dtsi" |
| #include "sdm845-camera-sensor-mtp.dtsi" |
| |
| &vendor { |
| qcom,battery-data { |
| #include "fg-gen3-batterydata-mlp356477-2800mah.dtsi" |
| }; |
| }; |
| |
| &sdhc_2 { |
| cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &usb1 { |
| status = "ok"; |
| dwc3@a800000 { |
| maximum-speed = "high-speed"; |
| dr_mode = "host"; |
| }; |
| }; |
| |
| &qusb_phy1 { |
| status = "ok"; |
| }; |
| |
| &usb_qmp_phy { |
| status = "ok"; |
| }; |
| |
| &tlmm { |
| pmx_ts_rst_active { |
| ts_rst_active: ts_rst_active { |
| mux { |
| pins = "gpio99"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio99"; |
| drive-strength = <16>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| pmx_ts_rst_suspend { |
| ts_rst_suspend: ts_rst_suspend { |
| mux { |
| pins = "gpio99"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio99"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| }; |
| }; |
| |
| &soc { |
| hbtp { |
| compatible = "qcom,hbtp-input"; |
| pinctrl-names = "pmx_ts_active", "pmx_ts_suspend"; |
| pinctrl-0 = <&ts_rst_active>; |
| pinctrl-1 = <&ts_rst_suspend>; |
| vcc_ana-supply = <&pm8998_l28>; |
| vcc_dig-supply = <&pm8998_l14>; |
| qcom,afe-load = <20000>; |
| qcom,afe-vtg-min = <3000000>; |
| qcom,afe-vtg-max = <3000000>; |
| qcom,dig-load = <40000>; |
| qcom,dig-vtg-min = <1800000>; |
| qcom,dig-vtg-max = <1800000>; |
| qcom,fb-resume-delay-us = <1000>; |
| qcom,afe-force-power-on; |
| qcom,afe-power-on-delay-us = <6>; |
| qcom,afe-power-off-delay-us = <6>; |
| }; |
| }; |
| |
| &qupv3_se5_i2c { |
| status = "disabled"; |
| }; |
| |