| /* |
| * Copyright (c) 2016-2018, 2020, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <dt-bindings/clock/qcom,gcc-sdm845.h> |
| #include <dt-bindings/msm/msm-bus-ids.h> |
| |
| &soc { |
| /* Primary USB port related DWC3 controller */ |
| usb0: ssusb@a600000 { |
| compatible = "qcom,dwc-usb3-msm"; |
| reg = <0x0a600000 0xf8c00>, |
| <0x088ee000 0x400>; |
| reg-names = "core_base", "ahb2phy_base"; |
| iommus = <&apps_smmu 0x740 0x0>; |
| qcom,smmu-s1-bypass; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| interrupts = <0 489 0>, <0 130 0>, <0 486 0>, <0 488 0>; |
| interrupt-names = "dp_hs_phy_irq", "pwr_event_irq", |
| "ss_phy_irq", "dm_hs_phy_irq"; |
| |
| USB3_GDSC-supply = <&usb30_prim_gdsc>; |
| qcom,usb-dbm = <&dbm_1p5>; |
| qcom,dwc-usb3-msm-tx-fifo-size = <21288>; |
| qcom,num-gsi-evt-buffs = <0x3>; |
| qcom,use-pdc-interrupts; |
| qcom,pm-qos-latency = <44>; |
| extcon = <0>, <0>, <&eud>, <0>, <0>; |
| |
| clocks = <&clock_gcc GCC_USB30_PRIM_MASTER_CLK>, |
| <&clock_gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, |
| <&clock_gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, |
| <&clock_gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&clock_gcc GCC_USB30_PRIM_SLEEP_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&clock_gcc GCC_USB3_PRIM_CLKREF_CLK>; |
| |
| clock-names = "core_clk", "iface_clk", "bus_aggr_clk", |
| "utmi_clk", "sleep_clk", "cfg_ahb_clk", "xo"; |
| |
| qcom,core-clk-rate = <133333333>; |
| qcom,core-clk-rate-hs = <66666667>; |
| |
| resets = <&clock_gcc GCC_USB30_PRIM_BCR>; |
| reset-names = "core_reset"; |
| |
| qcom,msm-bus,name = "usb0"; |
| qcom,msm-bus,num-cases = <2>; |
| qcom,msm-bus,num-paths = <3>; |
| qcom,msm-bus,vectors-KBps = |
| <MSM_BUS_MASTER_USB3 MSM_BUS_SLAVE_EBI_CH0 0 0>, |
| <MSM_BUS_MASTER_USB3 MSM_BUS_SLAVE_IPA_CFG 0 0>, |
| <MSM_BUS_MASTER_AMPSS_M0 MSM_BUS_SLAVE_USB3 0 0>, |
| <MSM_BUS_MASTER_USB3 |
| MSM_BUS_SLAVE_EBI_CH0 240000 700000>, |
| <MSM_BUS_MASTER_USB3 |
| MSM_BUS_SLAVE_IPA_CFG 0 2400>, |
| <MSM_BUS_MASTER_AMPSS_M0 MSM_BUS_SLAVE_USB3 0 40000>; |
| |
| dwc3@a600000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0a600000 0xcd00>; |
| interrupts = <0 133 0>; |
| usb-phy = <&qusb_phy0>, <&usb_qmp_dp_phy>; |
| tx-fifo-resize; |
| linux,sysdev_is_parent; |
| snps,disable-clk-gating; |
| snps,has-lpm-erratum; |
| snps,hird-threshold = /bits/ 8 <0x10>; |
| snps,usb3_lpm_capable; |
| usb-core-id = <0>; |
| }; |
| |
| qcom,usbbam@a704000 { |
| compatible = "qcom,usb-bam-msm"; |
| reg = <0xa704000 0x17000>; |
| interrupts = <0 132 0>; |
| |
| qcom,bam-type = <0>; |
| qcom,usb-bam-fifo-baseaddr = <0x146bb000>; |
| qcom,usb-bam-num-pipes = <8>; |
| qcom,ignore-core-reset-ack; |
| qcom,disable-clk-gating; |
| qcom,usb-bam-override-threshold = <0x4001>; |
| qcom,usb-bam-max-mbps-highspeed = <400>; |
| qcom,usb-bam-max-mbps-superspeed = <3600>; |
| qcom,reset-bam-on-connect; |
| |
| qcom,pipe0 { |
| label = "ssusb-qdss-in-0"; |
| qcom,usb-bam-mem-type = <2>; |
| qcom,dir = <1>; |
| qcom,pipe-num = <0>; |
| qcom,peer-bam = <0>; |
| qcom,peer-bam-physical-address = <0x6064000>; |
| qcom,src-bam-pipe-index = <0>; |
| qcom,dst-bam-pipe-index = <0>; |
| qcom,data-fifo-offset = <0x0>; |
| qcom,data-fifo-size = <0x1800>; |
| qcom,descriptor-fifo-offset = <0x1800>; |
| qcom,descriptor-fifo-size = <0x800>; |
| }; |
| }; |
| }; |
| |
| /* Primary USB port related QUSB2 PHY */ |
| qusb_phy0: qusb@88e2000 { |
| compatible = "qcom,qusb2phy-v2"; |
| reg = <0x088e2000 0x400>, |
| <0x007801e8 0x4>, |
| <0x088e7014 0x4>; |
| reg-names = "qusb_phy_base", "efuse_addr", |
| "refgen_north_bg_reg_addr"; |
| |
| qcom,efuse-bit-pos = <25>; |
| qcom,efuse-num-bits = <3>; |
| vdd-supply = <&pm8998_l1>; |
| vdda18-supply = <&pm8998_l12>; |
| vdda33-supply = <&pm8998_l24>; |
| qcom,override-bias-ctrl2; |
| qcom,vdd-voltage-level = <0 880000 880000>; |
| qcom,qusb-phy-reg-offset = |
| <0x240 /* QUSB2PHY_PORT_TUNE1 */ |
| 0x1a0 /* QUSB2PHY_PLL_COMMON_STATUS_ONE */ |
| 0x210 /* QUSB2PHY_PWR_CTRL1 */ |
| 0x230 /* QUSB2PHY_INTR_CTRL */ |
| 0x0a8 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE */ |
| 0x254 /* QUSB2PHY_TEST1 */ |
| 0x198 /* PLL_BIAS_CONTROL_2 */ |
| 0x228 /* QUSB2PHY_SQ_CTRL1 */ |
| 0x22c /* QUSB2PHY_SQ_CTRL2 */ |
| 0x27c /* QUSB2PHY_DEBUG_CTRL1 */ |
| 0x280 /* QUSB2PHY_DEBUG_CTRL2 */ |
| 0x284 /* QUSB2PHY_DEBUG_CTRL3 */ |
| 0x288 /* QUSB2PHY_DEBUG_CTRL4 */ |
| 0x2a0>; /* QUSB2PHY_STAT5 */ |
| |
| qcom,qusb-phy-init-seq = |
| /* <value reg_offset> */ |
| <0x23 0x210 /* PWR_CTRL1 */ |
| 0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */ |
| 0x7c 0x18c /* PLL_CLOCK_INVERTERS */ |
| 0x80 0x2c /* PLL_CMODE */ |
| 0x0a 0x184 /* PLL_LOCK_DELAY */ |
| 0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */ |
| 0x40 0x194 /* PLL_BIAS_CONTROL_1 */ |
| 0x20 0x198 /* PLL_BIAS_CONTROL_2 */ |
| 0x21 0x214 /* PWR_CTRL2 */ |
| 0x00 0x220 /* IMP_CTRL1 */ |
| 0x58 0x224 /* IMP_CTRL2 */ |
| 0x30 0x240 /* TUNE1 */ |
| 0x29 0x244 /* TUNE2 */ |
| 0xca 0x248 /* TUNE3 */ |
| 0x04 0x24c /* TUNE4 */ |
| 0x03 0x250 /* TUNE5 */ |
| 0x00 0x23c /* CHG_CTRL2 */ |
| 0x22 0x210>; /* PWR_CTRL1 */ |
| |
| phy_type= "utmi"; |
| clocks = <&clock_rpmh RPMH_CXO_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>; |
| clock-names = "ref_clk_src", "cfg_ahb_clk"; |
| |
| resets = <&clock_gcc GCC_QUSB2PHY_PRIM_BCR>; |
| reset-names = "phy_reset"; |
| }; |
| |
| /* Primary USB port related QMP USB DP Combo PHY */ |
| usb_qmp_dp_phy: ssphy@88e8000 { |
| compatible = "qcom,usb-ssphy-qmp-dp-combo"; |
| reg = <0x88e8000 0x3000>; |
| reg-names = "qmp_phy_base"; |
| |
| vdd-supply = <&pm8998_l1>; |
| core-supply = <&pm8998_l26>; |
| qcom,vdd-voltage-level = <0 880000 880000>; |
| qcom,vbus-valid-override; |
| qcom,qmp-phy-init-seq = |
| /* <reg_offset, value, delay> */ |
| <0x1048 0x07 0x00 /* COM_PLL_IVCO */ |
| 0x1080 0x14 0x00 /* COM_SYSCLK_EN_SEL */ |
| 0x1034 0x08 0x00 /* COM_BIAS_EN_CLKBUFLR_EN */ |
| 0x1138 0x30 0x00 /* COM_CLK_SELECT */ |
| 0x103c 0x02 0x00 /* COM_SYS_CLK_CTRL */ |
| 0x108c 0x08 0x00 /* COM_RESETSM_CNTRL2 */ |
| 0x115c 0x16 0x00 /* COM_CMN_CONFIG */ |
| 0x1164 0x01 0x00 /* COM_SVS_MODE_CLK_SEL */ |
| 0x113c 0x80 0x00 /* COM_HSCLK_SEL */ |
| 0x10b0 0x82 0x00 /* COM_DEC_START_MODE0 */ |
| 0x10b8 0xab 0x00 /* COM_DIV_FRAC_START1_MODE0 */ |
| 0x10bc 0xea 0x00 /* COM_DIV_FRAC_START2_MODE0 */ |
| 0x10c0 0x02 0x00 /* COM_DIV_FRAC_START3_MODE0 */ |
| 0x1060 0x06 0x00 /* COM_CP_CTRL_MODE0 */ |
| 0x1068 0x16 0x00 /* COM_PLL_RCTRL_MODE0 */ |
| 0x1070 0x36 0x00 /* COM_PLL_CCTRL_MODE0 */ |
| 0x10dc 0x00 0x00 /* COM_INTEGLOOP_GAIN1_MODE0 */ |
| 0x10d8 0x3f 0x00 /* COM_INTEGLOOP_GAIN0_MODE0 */ |
| 0x10f8 0x01 0x00 /* COM_VCO_TUNE2_MODE0 */ |
| 0x10f4 0xc9 0x00 /* COM_VCO_TUNE1_MODE0 */ |
| 0x1148 0x0a 0x00 /* COM_CORECLK_DIV_MODE0 */ |
| 0x10a0 0x00 0x00 /* COM_LOCK_CMP3_MODE0 */ |
| 0x109c 0x34 0x00 /* COM_LOCK_CMP2_MODE0 */ |
| 0x1098 0x15 0x00 /* COM_LOCK_CMP1_MODE0 */ |
| 0x1090 0x04 0x00 /* COM_LOCK_CMP_EN */ |
| 0x1154 0x00 0x00 /* COM_CORE_CLK_EN */ |
| 0x1094 0x00 0x00 /* COM_LOCK_CMP_CFG */ |
| 0x10f0 0x00 0x00 /* COM_VCO_TUNE_MAP */ |
| 0x1040 0x0a 0x00 /* COM_SYSCLK_BUF_ENABLE */ |
| 0x1010 0x01 0x00 /* COM_SSC_EN_CENTER */ |
| 0x101c 0x31 0x00 /* COM_SSC_PER1 */ |
| 0x1020 0x01 0x00 /* COM_SSC_PER2 */ |
| 0x1014 0x00 0x00 /* COM_SSC_ADJ_PER1 */ |
| 0x1018 0x00 0x00 /* COM_SSC_ADJ_PER2 */ |
| 0x1024 0x85 0x00 /* COM_SSC_STEP_SIZE1 */ |
| 0x1028 0x07 0x00 /* COM_SSC_STEP_SIZE2 */ |
| 0x1430 0x0b 0x00 /* RXA_UCDR_FASTLOCK_FO_GAIN */ |
| 0x14d4 0x0f 0x00 /* RXA_RX_EQU_ADAPTOR_CNTRL2 */ |
| 0x14d8 0x4e 0x00 /* RXA_RX_EQU_ADAPTOR_CNTRL3 */ |
| 0x14dc 0x18 0x00 /* RXA_RX_EQU_ADAPTOR_CNTRL4 */ |
| 0x14f8 0x77 0x00 /* RXA_RX_EQ_OFFSET_ADAPTOR_CNTRL1 */ |
| 0x14fc 0x80 0x00 /* RXA_RX_OFFSET_ADAPTOR_CNTRL2 */ |
| 0x1504 0x03 0x00 /* RXA_SIGDET_CNTRL */ |
| 0x150c 0x16 0x00 /* RXA_SIGDET_DEGLITCH_CNTRL */ |
| 0x1564 0x05 0x00 /* RXA_RX_MODE_00 */ |
| 0x14c0 0x03 0x00 /* RXA_VGA_CAL_CNTRL2 */ |
| 0x1830 0x0b 0x00 /* RXB_UCDR_FASTLOCK_FO_GAIN */ |
| 0x18d4 0x0f 0x00 /* RXB_RX_EQU_ADAPTOR_CNTRL2 */ |
| 0x18d8 0x4e 0x00 /* RXB_RX_EQU_ADAPTOR_CNTRL3 */ |
| 0x18dc 0x18 0x00 /* RXB_RX_EQU_ADAPTOR_CNTRL4 */ |
| 0x18f8 0x77 0x00 /* RXB_RX_EQ_OFFSET_ADAPTOR_CNTRL1 */ |
| 0x18fc 0x80 0x00 /* RXB_RX_OFFSET_ADAPTOR_CNTRL2 */ |
| 0x1904 0x03 0x00 /* RXB_SIGDET_CNTRL */ |
| 0x190c 0x16 0x00 /* RXB_SIGDET_DEGLITCH_CNTRL */ |
| 0x1964 0x05 0x00 /* RXB_RX_MODE_00 */ |
| 0x18c0 0x03 0x00 /* RXB_VGA_CAL_CNTRL2 */ |
| 0x1260 0x10 0x00 /* TXA_HIGHZ_DRVR_EN */ |
| 0x12a4 0x12 0x00 /* TXA_RCV_DETECT_LVL_2 */ |
| 0x128c 0x16 0x00 /* TXA_LANE_MODE_1 */ |
| 0x1248 0x09 0x00 /* TXA_RES_CODE_LANE_OFFSET_RX */ |
| 0x1244 0x06 0x00 /* TXA_RES_CODE_LANE_OFFSET_TX */ |
| 0x1660 0x10 0x00 /* TXB_HIGHZ_DRVR_EN */ |
| 0x16a4 0x12 0x00 /* TXB_RCV_DETECT_LVL_2 */ |
| 0x168c 0x16 0x00 /* TXB_LANE_MODE_1 */ |
| 0x1648 0x09 0x00 /* TXB_RES_CODE_LANE_OFFSET_RX */ |
| 0x1644 0x06 0x00 /* TXB_RES_CODE_LANE_OFFSET_TX */ |
| 0x1cc8 0x83 0x00 /* PCS_FLL_CNTRL2 */ |
| 0x1ccc 0x09 0x00 /* PCS_FLL_CNT_VAL_L */ |
| 0x1cd0 0xa2 0x00 /* PCS_FLL_CNT_VAL_H_TOL */ |
| 0x1cd4 0x40 0x00 /* PCS_FLL_MAN_CODE */ |
| 0x1cc4 0x02 0x00 /* PCS_FLL_CNTRL1 */ |
| 0x1c80 0xd1 0x00 /* PCS_LOCK_DETECT_CONFIG1 */ |
| 0x1c84 0x1f 0x00 /* PCS_LOCK_DETECT_CONFIG2 */ |
| 0x1c88 0x47 0x00 /* PCS_LOCK_DETECT_CONFIG3 */ |
| 0x1c64 0x1b 0x00 /* PCS_POWER_STATE_CONFIG2 */ |
| 0x1434 0x75 0x00 /* RXA_UCDR_SO_SATURATION */ |
| 0x1834 0x75 0x00 /* RXB_UCDR_SO_SATURATION */ |
| 0x1dd8 0xba 0x00 /* PCS_RX_SIGDET_LVL */ |
| 0x1c0c 0x9f 0x00 /* PCS_TXMGN_V0 */ |
| 0x1c10 0x9f 0x00 /* PCS_TXMGN_V1 */ |
| 0x1c14 0xb7 0x00 /* PCS_TXMGN_V2 */ |
| 0x1c18 0x4e 0x00 /* PCS_TXMGN_V3 */ |
| 0x1c1c 0x65 0x00 /* PCS_TXMGN_V4 */ |
| 0x1c20 0x6b 0x00 /* PCS_TXMGN_LS */ |
| 0x1c24 0x15 0x00 /* PCS_TXDEEMPH_M6DB_V0 */ |
| 0x1c28 0x0d 0x00 /* PCS_TXDEEMPH_M3P5DB_V0 */ |
| 0x1c2c 0x15 0x00 /* PCS_TXDEEMPH_M6DB_V1 */ |
| 0x1c30 0x0d 0x00 /* PCS_TXDEEMPH_M3P5DB_V1 */ |
| 0x1c34 0x15 0x00 /* PCS_TXDEEMPH_M6DB_V2 */ |
| 0x1c38 0x0d 0x00 /* PCS_TXDEEMPH_M3P5DB_V2 */ |
| 0x1c3c 0x15 0x00 /* PCS_TXDEEMPH_M6DB_V3 */ |
| 0x1c40 0x1d 0x00 /* PCS_TXDEEMPH_M3P5DB_V3 */ |
| 0x1c44 0x15 0x00 /* PCS_TXDEEMPH_M6DB_V4 */ |
| 0x1c48 0x0d 0x00 /* PCS_TXDEEMPH_M3P5DB_V4 */ |
| 0x1c4c 0x15 0x00 /* PCS_TXDEEMPH_M6DB_LS */ |
| 0x1c50 0x0d 0x00 /* PCS_TXDEEMPH_M3P5DB_LS */ |
| 0x1e0c 0x21 0x00 /* PCS_REFGEN_REQ_CONFIG1 */ |
| 0x1e10 0x60 0x00 /* PCS_REFGEN_REQ_CONFIG2 */ |
| 0x1c5c 0x02 0x00 /* PCS_RATE_SLEW_CNTRL */ |
| 0x1ca0 0x04 0x00 /* PCS_PWRUP_RESET_DLY_TIME_AUXCLK */ |
| 0x1c8c 0x44 0x00 /* PCS_TSYNC_RSYNC_TIME */ |
| 0x1c70 0xe7 0x00 /* PCS_RCVR_DTCT_DLY_P1U2_L */ |
| 0x1c74 0x03 0x00 /* PCS_RCVR_DTCT_DLY_P1U2_H */ |
| 0x1c78 0x40 0x00 /* PCS_RCVR_DTCT_DLY_U3_L */ |
| 0x1c7c 0x00 0x00 /* PCS_RCVR_DTCT_DLY_U3_H */ |
| 0x1cb8 0x75 0x00 /* PCS_RXEQTRAINING_WAIT_TIME */ |
| 0x1cb0 0x86 0x00 /* PCS_LFPS_TX_ECSTART_EQTLOCK */ |
| 0x1cbc 0x13 0x00 /* PCS_RXEQTRAINING_RUN_TIME */ |
| 0x1cac 0x04 0x00 /* PCS_LFPS_DET_HIGH_COUNT_VAL */ |
| 0xffffffff 0xffffffff 0x00>; |
| |
| qcom,qmp-phy-reg-offset = |
| <0x1d74 /* USB3_DP_PCS_PCS_STATUS */ |
| 0x1cd8 /* USB3_DP_PCS_AUTONOMOUS_MODE_CTRL */ |
| 0x1cdc /* USB3_DP_PCS_LFPS_RXTERM_IRQ_CLEAR */ |
| 0x1c04 /* USB3_DP_PCS_POWER_DOWN_CONTROL */ |
| 0x1c00 /* USB3_DP_PCS_SW_RESET */ |
| 0x1c08 /* USB3_DP_PCS_START_CONTROL */ |
| 0x2a18 /* USB3_DP_DP_PHY_PD_CTL */ |
| 0x0008 /* USB3_DP_COM_POWER_DOWN_CTRL */ |
| 0x0004 /* USB3_DP_COM_SW_RESET */ |
| 0x001c /* USB3_DP_COM_RESET_OVRD_CTRL */ |
| 0x0000 /* USB3_DP_COM_PHY_MODE_CTRL */ |
| 0x0010 /* USB3_DP_COM_TYPEC_CTRL */ |
| 0x000c /* USB3_DP_COM_SWI_CTRL */ |
| 0x1a0c>; /* USB3_DP_PCS_MISC_CLAMP_ENABLE */ |
| |
| clocks = <&clock_gcc GCC_USB3_PRIM_PHY_AUX_CLK>, |
| <&clock_gcc GCC_USB3_PRIM_PHY_PIPE_CLK>, |
| <&clock_rpmh RPMH_CXO_CLK>, |
| <&clock_gcc GCC_USB3_PRIM_CLKREF_CLK>, |
| <&clock_gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>; |
| |
| clock-names = "aux_clk", "pipe_clk", "ref_clk_src", |
| "ref_clk", "com_aux_clk", "cfg_ahb_clk"; |
| |
| resets = <&clock_gcc GCC_USB3_DP_PHY_PRIM_BCR>, |
| <&clock_gcc GCC_USB3_PHY_PRIM_BCR>; |
| reset-names = "global_phy_reset", "phy_reset"; |
| }; |
| |
| dbm_1p5: dbm@a6f8000 { |
| compatible = "qcom,usb-dbm-1p5"; |
| reg = <0xa6f8000 0x400>; |
| qcom,reset-ep-after-lpm-resume; |
| }; |
| |
| usb_audio_qmi_dev { |
| compatible = "qcom,usb-audio-qmi-dev"; |
| iommus = <&apps_smmu 0x182c 0x0>; |
| qcom,usb-audio-stream-id = <0xc>; |
| qcom,usb-audio-intr-num = <2>; |
| }; |
| |
| usb_nop_phy: usb_nop_phy { |
| compatible = "usb-nop-xceiv"; |
| }; |
| |
| /* Secondary USB port related DWC3 controller */ |
| usb1: ssusb@a800000 { |
| compatible = "qcom,dwc-usb3-msm"; |
| reg = <0x0a800000 0xf8c00>, |
| <0x088ee000 0x400>; |
| reg-names = "core_base", "ahb2phy_base"; |
| iommus = <&apps_smmu 0x760 0x0>; |
| qcom,smmu-s1-bypass; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| interrupts = <0 491 0>, <0 135 0>, <0 487 0>, <0 490 0>; |
| interrupt-names = "dp_hs_phy_irq", "pwr_event_irq", |
| "ss_phy_irq", "dm_hs_phy_irq"; |
| |
| USB3_GDSC-supply = <&usb30_sec_gdsc>; |
| qcom,dwc-usb3-msm-tx-fifo-size = <21288>; |
| qcom,use-pdc-interrupts; |
| |
| clocks = <&clock_gcc GCC_USB30_SEC_MASTER_CLK>, |
| <&clock_gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, |
| <&clock_gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, |
| <&clock_gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, |
| <&clock_gcc GCC_USB30_SEC_SLEEP_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, |
| <&clock_gcc GCC_USB3_SEC_CLKREF_CLK>; |
| |
| clock-names = "core_clk", "iface_clk", "bus_aggr_clk", |
| "utmi_clk", "sleep_clk", "cfg_ahb_clk", "xo"; |
| |
| qcom,core-clk-rate = <133333333>; |
| qcom,core-clk-rate-hs = <66666667>; |
| |
| resets = <&clock_gcc GCC_USB30_SEC_BCR>; |
| reset-names = "core_reset"; |
| status = "disabled"; |
| |
| qcom,msm-bus,name = "usb1"; |
| qcom,msm-bus,num-cases = <2>; |
| qcom,msm-bus,num-paths = <2>; |
| qcom,msm-bus,vectors-KBps = |
| <MSM_BUS_MASTER_USB3_1 MSM_BUS_SLAVE_EBI_CH0 0 0>, |
| <MSM_BUS_MASTER_AMPSS_M0 MSM_BUS_SLAVE_USB3_1 0 0>, |
| <MSM_BUS_MASTER_USB3_1 |
| MSM_BUS_SLAVE_EBI_CH0 240000 700000>, |
| <MSM_BUS_MASTER_AMPSS_M0 MSM_BUS_SLAVE_USB3_1 0 40000>; |
| |
| dwc3@a800000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0a800000 0xcd00>; |
| interrupts = <0 138 0>; |
| usb-phy = <&qusb_phy1>, <&usb_qmp_phy>; |
| tx-fifo-resize; |
| linux,sysdev_is_parent; |
| snps,disable-clk-gating; |
| snps,has-lpm-erratum; |
| snps,hird-threshold = /bits/ 8 <0x10>; |
| snps,usb3_lpm_capable; |
| usb-core-id = <1>; |
| dr_mode = "host"; |
| }; |
| }; |
| |
| /* Secondary USB port related QUSB2 PHY */ |
| qusb_phy1: qusb@88e3000 { |
| compatible = "qcom,qusb2phy-v2"; |
| reg = <0x088e3000 0x400>, |
| <0x088e7014 0x4>; |
| reg-names = "qusb_phy_base", |
| "refgen_north_bg_reg_addr"; |
| |
| vdd-supply = <&pm8998_l1>; |
| vdda18-supply = <&pm8998_l12>; |
| vdda33-supply = <&pm8998_l24>; |
| qcom,override-bias-ctrl2; |
| qcom,vdd-voltage-level = <0 880000 880000>; |
| qcom,qusb-phy-reg-offset = |
| <0x240 /* QUSB2PHY_PORT_TUNE1 */ |
| 0x1a0 /* QUSB2PHY_PLL_COMMON_STATUS_ONE */ |
| 0x210 /* QUSB2PHY_PWR_CTRL1 */ |
| 0x230 /* QUSB2PHY_INTR_CTRL */ |
| 0x0a8 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE */ |
| 0x254 /* QUSB2PHY_TEST1 */ |
| 0x198 /* PLL_BIAS_CONTROL_2 */ |
| 0x228 /* QUSB2PHY_SQ_CTRL1 */ |
| 0x22c /* QUSB2PHY_SQ_CTRL2 */ |
| 0x27c /* QUSB2PHY_DEBUG_CTRL1 */ |
| 0x280 /* QUSB2PHY_DEBUG_CTRL2 */ |
| 0x2a0>; /* QUSB2PHY_STAT5 */ |
| |
| qcom,qusb-phy-init-seq = |
| /* <value reg_offset> */ |
| <0x23 0x210 /* PWR_CTRL1 */ |
| 0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */ |
| 0x7c 0x18c /* PLL_CLOCK_INVERTERS */ |
| 0x80 0x2c /* PLL_CMODE */ |
| 0x0a 0x184 /* PLL_LOCK_DELAY */ |
| 0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */ |
| 0x40 0x194 /* PLL_BIAS_CONTROL_1 */ |
| 0x20 0x198 /* PLL_BIAS_CONTROL_2 */ |
| 0x21 0x214 /* PWR_CTRL2 */ |
| 0x00 0x220 /* IMP_CTRL1 */ |
| 0x58 0x224 /* IMP_CTRL2 */ |
| 0x20 0x240 /* TUNE1 */ |
| 0x29 0x244 /* TUNE2 */ |
| 0xca 0x248 /* TUNE3 */ |
| 0x04 0x24c /* TUNE4 */ |
| 0x03 0x250 /* TUNE5 */ |
| 0x00 0x23c /* CHG_CTRL2 */ |
| 0x22 0x210>; /* PWR_CTRL1 */ |
| |
| phy_type= "utmi"; |
| clocks = <&clock_rpmh RPMH_CXO_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>; |
| clock-names = "ref_clk_src", "cfg_ahb_clk"; |
| |
| resets = <&clock_gcc GCC_QUSB2PHY_SEC_BCR>; |
| reset-names = "phy_reset"; |
| status = "disabled"; |
| }; |
| |
| /* Secondary USB port related QMP PHY */ |
| usb_qmp_phy: ssphy@88eb000 { |
| compatible = "qcom,usb-ssphy-qmp-v2"; |
| reg = <0x88eb000 0x1000>, |
| <0x01fcbff0 0x4>; |
| reg-names = "qmp_phy_base", |
| "vls_clamp_reg"; |
| |
| vdd-supply = <&pm8998_l1>; |
| core-supply = <&pm8998_l26>; |
| qcom,vdd-voltage-level = <0 880000 880000>; |
| qcom,vbus-valid-override; |
| qcom,qmp-phy-init-seq = |
| /* <reg_offset, value, delay> */ |
| <0x048 0x07 0x00 /* QSERDES_COM_PLL_IVCO */ |
| 0x080 0x14 0x00 /* QSERDES_COM_SYSCLK_EN_SEL */ |
| 0x034 0x04 0x00 /* QSERDES_COM_BIAS_EN_CLKBUFLR_EN */ |
| 0x138 0x30 0x00 /* QSERDES_COM_CLK_SELECT */ |
| 0x03c 0x02 0x00 /* QSERDES_COM_SYS_CLK_CTRL */ |
| 0x08c 0x08 0x00 /* QSERDES_COM_RESETSM_CNTRL2 */ |
| 0x15c 0x06 0x00 /* QSERDES_COM_CMN_CONFIG */ |
| 0x164 0x01 0x00 /* QSERDES_COM_SVS_MODE_CLK_SEL */ |
| 0x13c 0x80 0x00 /* QSERDES_COM_HSCLK_SEL */ |
| 0x0b0 0x82 0x00 /* QSERDES_COM_DEC_START_MODE0 */ |
| 0x0b8 0xab 0x00 /* QSERDES_COM_DIV_FRAC_START1_MODE0 */ |
| 0x0bc 0xea 0x00 /* QSERDES_COM_DIV_FRAC_START2_MODE0 */ |
| 0x0c0 0x02 0x00 /* QSERDES_COM_DIV_FRAC_START3_MODE0 */ |
| 0x060 0x06 0x00 /* QSERDES_COM_CP_CTRL_MODE0 */ |
| 0x068 0x16 0x00 /* QSERDES_COM_PLL_RCTRL_MODE0 */ |
| 0x070 0x36 0x00 /* QSERDES_COM_PLL_CCTRL_MODE0 */ |
| 0x0dc 0x00 0x00 /* QSERDES_COM_INTEGLOOP_GAIN1_MODE0 */ |
| 0x0d8 0x3f 0x00 /* QSERDES_COM_INTEGLOOP_GAIN0_MODE0 */ |
| 0x0f8 0x01 0x00 /* QSERDES_COM_VCO_TUNE2_MODE0 */ |
| 0x0f4 0xc9 0x00 /* QSERDES_COM_VCO_TUNE1_MODE0 */ |
| 0x148 0x0a 0x00 /* QSERDES_COM_CORECLK_DIV_MODE0 */ |
| 0x0a0 0x00 0x00 /* QSERDES_COM_LOCK_CMP3_MODE0 */ |
| 0x09c 0x34 0x00 /* QSERDES_COM_LOCK_CMP2_MODE0 */ |
| 0x098 0x15 0x00 /* QSERDES_COM_LOCK_CMP1_MODE0 */ |
| 0x090 0x04 0x00 /* QSERDES_COM_LOCK_CMP_EN */ |
| 0x154 0x00 0x00 /* QSERDES_COM_CORE_CLK_EN */ |
| 0x094 0x00 0x00 /* QSERDES_COM_LOCK_CMP_CFG */ |
| 0x0f0 0x00 0x00 /* QSERDES_COM_VCO_TUNE_MAP */ |
| 0x040 0x0a 0x00 /* QSERDES_COM_SYSCLK_BUF_ENABLE */ |
| 0x0d0 0x80 0x00 /* QSERDES_COM_INTEGLOOP_INITVAL */ |
| 0x010 0x01 0x00 /* QSERDES_COM_SSC_EN_CENTER */ |
| 0x01c 0x31 0x00 /* QSERDES_COM_SSC_PER1 */ |
| 0x020 0x01 0x00 /* QSERDES_COM_SSC_PER2 */ |
| 0x014 0x00 0x00 /* QSERDES_COM_SSC_ADJ_PER1 */ |
| 0x018 0x00 0x00 /* QSERDES_COM_SSC_ADJ_PER2 */ |
| 0x024 0x85 0x00 /* QSERDES_COM_SSC_STEP_SIZE1 */ |
| 0x028 0x07 0x00 /* QSERDES_COM_SSC_STEP_SIZE2 */ |
| 0x4c0 0x0c 0x00 /* QSERDES_RX_VGA_CAL_CNTRL2 */ |
| 0x564 0x50 0x00 /* QSERDES_RX_RX_MODE_00 */ |
| 0x430 0x0b 0x00 /* QSERDES_RX_UCDR_FASTLOCK_FO_GAIN */ |
| 0x4d4 0x0e 0x00 /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 */ |
| 0x4d8 0x4e 0x00 /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 */ |
| 0x4dc 0x18 0x00 /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 */ |
| 0x4f8 0x77 0x00 /* RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 */ |
| 0x4fc 0x80 0x00 /* RX_RX_OFFSET_ADAPTOR_CNTRL2 */ |
| 0x504 0x03 0x00 /* QSERDES_RX_SIGDET_CNTRL */ |
| 0x50c 0x1c 0x00 /* QSERDES_RX_SIGDET_DEGLITCH_CNTRL */ |
| 0x434 0x75 0x00 /* RX_UCDR_SO_SATURATION_AND_ENABLE */ |
| 0x444 0x80 0x00 /* QSERDES_RX_UCDR_PI_CONTROLS */ |
| 0x408 0x0a 0x00 /* QSERDES_RX_UCDR_FO_GAIN */ |
| 0x40c 0x06 0x00 /* QSERDES_RX_UCDR_SO_GAIN */ |
| 0x500 0x00 0x00 /* QSERDES_RX_SIGDET_ENABLES */ |
| 0x260 0x10 0x00 /* QSERDES_TX_HIGHZ_DRVR_EN */ |
| 0x2a4 0x12 0x00 /* QSERDES_TX_RCV_DETECT_LVL_2 */ |
| 0x28c 0xc6 0x00 /* QSERDES_TX_LANE_MODE_1 */ |
| 0x248 0x06 0x00 /* TX_RES_CODE_LANE_OFFSET_RX */ |
| 0x244 0x06 0x00 /* TX_RES_CODE_LANE_OFFSET_TX */ |
| 0x8c8 0x83 0x00 /* USB3_UNI_PCS_FLL_CNTRL2 */ |
| 0x8cc 0x09 0x00 /* USB3_UNI_PCS_FLL_CNT_VAL_L */ |
| 0x8d0 0xa2 0x00 /* USB3_UNI_PCS_FLL_CNT_VAL_H_TOL */ |
| 0x8d4 0x40 0x00 /* USB3_UNI_PCS_FLL_MAN_CODE */ |
| 0x8c4 0x02 0x00 /* USB3_UNI_PCS_FLL_CNTRL1 */ |
| 0x864 0x1b 0x00 /* USB3_UNI_PCS_POWER_STATE_CONFIG2 */ |
| 0x80c 0x9f 0x00 /* USB3_UNI_PCS_TXMGN_V0 */ |
| 0x810 0x9f 0x00 /* USB3_UNI_PCS_TXMGN_V1 */ |
| 0x814 0xb5 0x00 /* USB3_UNI_PCS_TXMGN_V2 */ |
| 0x818 0x4c 0x00 /* USB3_UNI_PCS_TXMGN_V3 */ |
| 0x81c 0x64 0x00 /* USB3_UNI_PCS_TXMGN_V4 */ |
| 0x820 0x6a 0x00 /* USB3_UNI_PCS_TXMGN_LS */ |
| 0x824 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_V0 */ |
| 0x828 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_V0 */ |
| 0x82c 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_V1 */ |
| 0x830 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_V1 */ |
| 0x834 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_V2 */ |
| 0x838 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_V2 */ |
| 0x83c 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_V3 */ |
| 0x840 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_V3 */ |
| 0x844 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_V4 */ |
| 0x848 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_V4 */ |
| 0x84c 0x15 0x00 /* USB3_UNI_PCS_TXDEEMPH_M6DB_LS */ |
| 0x850 0x0d 0x00 /* USB3_UNI_PCS_TXDEEMPH_M3P5DB_LS */ |
| 0x85c 0x02 0x00 /* USB3_UNI_PCS_RATE_SLEW_CNTRL */ |
| 0x8a0 0x04 0x00 /* PCS_PWRUP_RESET_DLY_TIME_AUXCLK */ |
| 0x88c 0x44 0x00 /* USB3_UNI_PCS_TSYNC_RSYNC_TIME */ |
| 0x880 0xd1 0x00 /* USB3_UNI_PCS_LOCK_DETECT_CONFIG1 */ |
| 0x884 0x1f 0x00 /* USB3_UNI_PCS_LOCK_DETECT_CONFIG2 */ |
| 0x888 0x47 0x00 /* USB3_UNI_PCS_LOCK_DETECT_CONFIG3 */ |
| 0x870 0xe7 0x00 /* USB3_UNI_PCS_RCVR_DTCT_DLY_P1U2_L */ |
| 0x874 0x03 0x00 /* USB3_UNI_PCS_RCVR_DTCT_DLY_P1U2_H */ |
| 0x878 0x40 0x00 /* USB3_UNI_PCS_RCVR_DTCT_DLY_U3_L */ |
| 0x87c 0x00 0x00 /* USB3_UNI_PCS_RCVR_DTCT_DLY_U3_H */ |
| 0x9d8 0xba 0x00 /* USB3_UNI_PCS_RX_SIGDET_LVL */ |
| 0x8b8 0x75 0x00 /* RXEQTRAINING_WAIT_TIME */ |
| 0x8b0 0x86 0x00 /* PCS_LFPS_TX_ECSTART_EQTLOCK */ |
| 0x8bc 0x13 0x00 /* PCS_RXEQTRAINING_RUN_TIME */ |
| 0xa0c 0x21 0x00 /* USB3_UNI_PCS_REFGEN_REQ_CONFIG1 */ |
| 0xa10 0x60 0x00 /* USB3_UNI_PCS_REFGEN_REQ_CONFIG2 */ |
| 0xffffffff 0xffffffff 0x00>; |
| |
| qcom,qmp-phy-reg-offset = |
| <0x974 /* USB3_UNI_PCS_PCS_STATUS */ |
| 0x8d8 /* USB3_UNI_PCS_AUTONOMOUS_MODE_CTRL */ |
| 0x8dc /* USB3_UNI_PCS_LFPS_RXTERM_IRQ_CLEAR */ |
| 0x804 /* USB3_UNI_PCS_POWER_DOWN_CONTROL */ |
| 0x800 /* USB3_UNI_PCS_SW_RESET */ |
| 0x808>; /* USB3_UNI_PCS_START_CONTROL */ |
| |
| clocks = <&clock_gcc GCC_USB3_SEC_PHY_AUX_CLK>, |
| <&clock_gcc GCC_USB3_SEC_PHY_PIPE_CLK>, |
| <&clock_rpmh RPMH_CXO_CLK>, |
| <&clock_gcc GCC_USB3_SEC_CLKREF_CLK>, |
| <&clock_gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>; |
| |
| clock-names = "aux_clk", "pipe_clk", "ref_clk_src", |
| "ref_clk", "cfg_ahb_clk"; |
| |
| resets = <&clock_gcc GCC_USB3_PHY_SEC_BCR>, |
| <&clock_gcc GCC_USB3PHY_PHY_SEC_BCR>; |
| reset-names = "phy_reset", "phy_phy_reset"; |
| status = "disabled"; |
| }; |
| }; |