| /* |
| * Copyright (c) 2018, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| /dts-v1/; |
| /plugin/; |
| |
| #include <dt-bindings/clock/qcom,gcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,camcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,dispcc-sdm845.h> |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| #include "sdm670-mtp.dtsi" |
| #include "sdm670-audio-overlay.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SXR1130 PM660 + PM660L MTP"; |
| compatible = "qcom,sxr1130-mtp", "qcom,sxr1130", "qcom,mtp"; |
| qcom,msm-id = <371 0x0>; |
| qcom,board-id = <8 0>; |
| qcom,pmic-id = <0x0001001b 0x0101011a 0x0 0x0>, |
| <0x0001001b 0x0102001a 0x0 0x0>, |
| <0x0001001b 0x0201011a 0x0 0x0>; |
| }; |
| |
| &cam_cci { |
| /delete-node/ qcom,cam-sensor@1; |
| qcom,cam-sensor@1 { |
| cell-index = <1>; |
| compatible = "qcom,cam-sensor"; |
| reg = <0x1>; |
| csiphy-sd-index = <1>; |
| sensor-position-roll = <90>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| eeprom-src = <&eeprom_rear_aux>; |
| cam_vio-supply = <&camera_vio_ldo>; |
| cam_vana-supply = <&camera_vana_ldo>; |
| cam_vdig-supply = <&camera_ldo>; |
| cam_clk-supply = <&titan_top_gdsc>; |
| regulator-names = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1352000 1800000 2850000 0>; |
| rgltr-max-voltage = <1352000 1800000 2850000 0>; |
| rgltr-load-current = <105000 0 80000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear2_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear2_suspend>; |
| gpios = <&tlmm 13 0>, |
| <&tlmm 28 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET1"; |
| sensor-mode = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_camcc CAM_CC_MCLK0_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| }; |