Documentation/video4linux/cx2341x/fw-decoder-api.txt - kernel/msm-4.9 - Gitiles

 Decoder firmware API description
 ================================

 Note: this API is part of the decoder firmware, so it's cx23415 only.

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_PING_FW
 Enum 	0/0x00
 Description
 	This API call does nothing. It may be used to check if the firmware
 	is responding.

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_START_PLAYBACK
 Enum 	1/0x01
 Description
 	Begin or resume playback.
 Param[0]
 	0 based frame number in GOP to begin playback from.
 Param[1]
 	Specifies the number of muted audio frames to play before normal
 	audio resumes. (This is not implemented in the firmware, leave at 0)

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_STOP_PLAYBACK
 Enum 	2/0x02
 Description
 	Ends playback and clears all decoder buffers. If PTS is not zero,
 	playback stops at specified PTS.
 Param[0]
 	Display 0=last frame, 1=black
 	Note: this takes effect immediately, so if you want to wait for a PTS,
 	then use '0', otherwise the screen goes to black at once.
 	You can call this later (even if there is no playback) with a 1 value
 	to set the screen to black.
 Param[1]
 	PTS low
 Param[2]
 	PTS high

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_PLAYBACK_SPEED
 Enum 	3/0x03
 Description
 	Playback stream at speed other than normal. There are two modes of
 	operation:
 	    Smooth: host transfers entire stream and firmware drops unused
 		    frames.
 	    Coarse: host drops frames based on indexing as required to achieve
 		    desired speed.
 Param[0]
 	Bitmap:
 	    0:7  0 normal
 		 1 fast only "1.5 times"
 		 n nX fast, 1/nX slow
 	    30   Framedrop:
 		     '0' during 1.5 times play, every other B frame is dropped
 		     '1' during 1.5 times play, stream is unchanged (bitrate
 			 must not exceed 8mbps)
 	    31   Speed:
 		     '0' slow
 		     '1' fast
 	Note: n is limited to 2. Anything higher does not result in
 	faster playback. Instead the host should start dropping frames.
 Param[1]
 	Direction: 0=forward, 1=reverse
 	Note: to make reverse playback work you have to write full GOPs in
 	reverse order.
 Param[2]
 	Picture mask:
 	    1=I frames
 	    3=I, P frames
 	    7=I, P, B frames
 Param[3]
 	B frames per GOP (for reverse play only)
 	Note: for reverse playback the Picture Mask should be set to I or I, P.
 	Adding B frames to the mask will result in corrupt video. This field
 	has to be set to the correct value in order to keep the timing correct.
 Param[4]
 	Mute audio: 0=disable, 1=enable
 Param[5]
 	Display 0=frame, 1=field
 Param[6]
 	Specifies the number of muted audio frames to play before normal audio
 	resumes. (Not implemented in the firmware, leave at 0)

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_STEP_VIDEO
 Enum 	5/0x05
 Description
 	Each call to this API steps the playback to the next unit defined below
 	in the current playback direction.
 Param[0]
 	0=frame, 1=top field, 2=bottom field

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_DMA_BLOCK_SIZE
 Enum 	8/0x08
 Description
 	Set DMA transfer block size. Counterpart to API 0xC9
 Param[0]
 	DMA transfer block size in bytes. A different size may be specified
 	when issuing the DMA transfer command.

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_GET_XFER_INFO
 Enum 	9/0x09
 Description
 	This API call may be used to detect an end of stream condition.
 Result[0]
 	Stream type
 Result[1]
 	Address offset
 Result[2]
 	Maximum bytes to transfer
 Result[3]
 	Buffer fullness

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_GET_DMA_STATUS
 Enum 	10/0x0A
 Description
 	Status of the last DMA transfer
 Result[0]
 	Bit 1 set means transfer complete
 	Bit 2 set means DMA error
 	Bit 3 set means linked list error
 Result[1]
 	DMA type: 0=MPEG, 1=OSD, 2=YUV

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SCHED_DMA_FROM_HOST
 Enum 	11/0x0B
 Description
 	Setup DMA from host operation. Counterpart to API 0xCC
 Param[0]
 	Memory address of link list
 Param[1]
 	Total # of bytes to transfer
 Param[2]
 	DMA type (0=MPEG, 1=OSD, 2=YUV)

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_PAUSE_PLAYBACK
 Enum 	13/0x0D
 Description
 	Freeze playback immediately. In this mode, when internal buffers are
 	full, no more data will be accepted and data request IRQs will be
 	masked.
 Param[0]
 	Display: 0=last frame, 1=black

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_HALT_FW
 Enum 	14/0x0E
 Description
 	The firmware is halted and no further API calls are serviced until
 	the firmware is uploaded again.

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_STANDARD
 Enum 	16/0x10
 Description
 	Selects display standard
 Param[0]
 	0=NTSC, 1=PAL

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_GET_VERSION
 Enum 	17/0x11
 Description
 	Returns decoder firmware version information
 Result[0]
 	Version bitmask:
 	    Bits  0:15 build
 	    Bits 16:23 minor
 	    Bits 24:31 major

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_STREAM_INPUT
 Enum 	20/0x14
 Description
 	Select decoder stream input port
 Param[0]
 	0=memory (default), 1=streaming

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_GET_TIMING_INFO
 Enum 	21/0x15
 Description
 	Returns timing information from start of playback
 Result[0]
 	Frame count by decode order
 Result[1]
 	Video PTS bits 0:31 by display order
 Result[2]
 	Video PTS bit 32 by display order
 Result[3]
 	SCR bits 0:31 by display order
 Result[4]
 	SCR bit 32 by display order

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_AUDIO_MODE
 Enum 	22/0x16
 Description
 	Select audio mode
 Param[0]
 	Dual mono mode action
 	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
 Param[1]
 	Stereo mode action:
 	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_EVENT_NOTIFICATION
 Enum 	23/0x17
 Description
 	Setup firmware to notify the host about a particular event.
 	Counterpart to API 0xD5
 Param[0]
 	Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
 	Event: 3=Decoder started
 	Event: 4=Unknown: goes off 10-15 times per second while decoding.
 	Event: 5=Some sync event: goes off once per frame.
 Param[1]
 	Notification 0=disabled, 1=enabled
 Param[2]
 	Interrupt bit
 Param[3]
 	Mailbox slot, -1 if no mailbox required.

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_DISPLAY_BUFFERS
 Enum 	24/0x18
 Description
 	Number of display buffers. To decode all frames in reverse playback you
 	must use nine buffers.
 Param[0]
 	0=six buffers, 1=nine buffers

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_EXTRACT_VBI
 Enum 	25/0x19
 Description
 	Extracts VBI data
 Param[0]
 	0=extract from extension & user data, 1=extract from private packets
 Result[0]
 	VBI table location
 Result[1]
 	VBI table size

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_DECODER_SOURCE
 Enum 	26/0x1A
 Description
 	Selects decoder source. Ensure that the parameters passed to this
 	API match the encoder settings.
 Param[0]
 	Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
 Param[1]
 	YUV picture width
 Param[2]
 	YUV picture height
 Param[3]
 	Bitmap: see Param[0] of API 0xBD

 -------------------------------------------------------------------------------

 Name 	CX2341X_DEC_SET_PREBUFFERING
 Enum 	30/0x1E
 Description
 	Decoder prebuffering, when enabled up to 128KB are buffered for
 	streams <8mpbs or 640KB for streams >8mbps
 Param[0]
 	0=off, 1=on
	Decoder firmware API description
	================================

	Note: this API is part of the decoder firmware, so it's cx23415 only.

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_PING_FW
	Enum 0/0x00
	Description
	This API call does nothing. It may be used to check if the firmware
	is responding.

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_START_PLAYBACK
	Enum 1/0x01
	Description
	Begin or resume playback.
	Param[0]
	0 based frame number in GOP to begin playback from.
	Param[1]
	Specifies the number of muted audio frames to play before normal
	audio resumes. (This is not implemented in the firmware, leave at 0)

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_STOP_PLAYBACK
	Enum 2/0x02
	Description
	Ends playback and clears all decoder buffers. If PTS is not zero,
	playback stops at specified PTS.
	Param[0]
	Display 0=last frame, 1=black
	Note: this takes effect immediately, so if you want to wait for a PTS,
	then use '0', otherwise the screen goes to black at once.
	You can call this later (even if there is no playback) with a 1 value
	to set the screen to black.
	Param[1]
	PTS low
	Param[2]
	PTS high

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_PLAYBACK_SPEED
	Enum 3/0x03
	Description
	Playback stream at speed other than normal. There are two modes of
	operation:
	Smooth: host transfers entire stream and firmware drops unused
	frames.
	Coarse: host drops frames based on indexing as required to achieve
	desired speed.
	Param[0]
	Bitmap:
	0:7 0 normal
	1 fast only "1.5 times"
	n nX fast, 1/nX slow
	30 Framedrop:
	'0' during 1.5 times play, every other B frame is dropped
	'1' during 1.5 times play, stream is unchanged (bitrate
	must not exceed 8mbps)
	31 Speed:
	'0' slow
	'1' fast
	Note: n is limited to 2. Anything higher does not result in
	faster playback. Instead the host should start dropping frames.
	Param[1]
	Direction: 0=forward, 1=reverse
	Note: to make reverse playback work you have to write full GOPs in
	reverse order.
	Param[2]
	Picture mask:
	1=I frames
	3=I, P frames
	7=I, P, B frames
	Param[3]
	B frames per GOP (for reverse play only)
	Note: for reverse playback the Picture Mask should be set to I or I, P.
	Adding B frames to the mask will result in corrupt video. This field
	has to be set to the correct value in order to keep the timing correct.
	Param[4]
	Mute audio: 0=disable, 1=enable
	Param[5]
	Display 0=frame, 1=field
	Param[6]
	Specifies the number of muted audio frames to play before normal audio
	resumes. (Not implemented in the firmware, leave at 0)

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_STEP_VIDEO
	Enum 5/0x05
	Description
	Each call to this API steps the playback to the next unit defined below
	in the current playback direction.
	Param[0]
	0=frame, 1=top field, 2=bottom field

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_DMA_BLOCK_SIZE
	Enum 8/0x08
	Description
	Set DMA transfer block size. Counterpart to API 0xC9
	Param[0]
	DMA transfer block size in bytes. A different size may be specified
	when issuing the DMA transfer command.

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_GET_XFER_INFO
	Enum 9/0x09
	Description
	This API call may be used to detect an end of stream condition.
	Result[0]
	Stream type
	Result[1]
	Address offset
	Result[2]
	Maximum bytes to transfer
	Result[3]
	Buffer fullness

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_GET_DMA_STATUS
	Enum 10/0x0A
	Description
	Status of the last DMA transfer
	Result[0]
	Bit 1 set means transfer complete
	Bit 2 set means DMA error
	Bit 3 set means linked list error
	Result[1]
	DMA type: 0=MPEG, 1=OSD, 2=YUV

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SCHED_DMA_FROM_HOST
	Enum 11/0x0B
	Description
	Setup DMA from host operation. Counterpart to API 0xCC
	Param[0]
	Memory address of link list
	Param[1]
	Total # of bytes to transfer
	Param[2]
	DMA type (0=MPEG, 1=OSD, 2=YUV)

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_PAUSE_PLAYBACK
	Enum 13/0x0D
	Description
	Freeze playback immediately. In this mode, when internal buffers are
	full, no more data will be accepted and data request IRQs will be
	masked.
	Param[0]
	Display: 0=last frame, 1=black

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_HALT_FW
	Enum 14/0x0E
	Description
	The firmware is halted and no further API calls are serviced until
	the firmware is uploaded again.

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_STANDARD
	Enum 16/0x10
	Description
	Selects display standard
	Param[0]
	0=NTSC, 1=PAL

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_GET_VERSION
	Enum 17/0x11
	Description
	Returns decoder firmware version information
	Result[0]
	Version bitmask:
	Bits 0:15 build
	Bits 16:23 minor
	Bits 24:31 major

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_STREAM_INPUT
	Enum 20/0x14
	Description
	Select decoder stream input port
	Param[0]
	0=memory (default), 1=streaming

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_GET_TIMING_INFO
	Enum 21/0x15
	Description
	Returns timing information from start of playback
	Result[0]
	Frame count by decode order
	Result[1]
	Video PTS bits 0:31 by display order
	Result[2]
	Video PTS bit 32 by display order
	Result[3]
	SCR bits 0:31 by display order
	Result[4]
	SCR bit 32 by display order

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_AUDIO_MODE
	Enum 22/0x16
	Description
	Select audio mode
	Param[0]
	Dual mono mode action
	0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
	Param[1]
	Stereo mode action:
	0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_EVENT_NOTIFICATION
	Enum 23/0x17
	Description
	Setup firmware to notify the host about a particular event.
	Counterpart to API 0xD5
	Param[0]
	Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
	Event: 3=Decoder started
	Event: 4=Unknown: goes off 10-15 times per second while decoding.
	Event: 5=Some sync event: goes off once per frame.
	Param[1]
	Notification 0=disabled, 1=enabled
	Param[2]
	Interrupt bit
	Param[3]
	Mailbox slot, -1 if no mailbox required.

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_DISPLAY_BUFFERS
	Enum 24/0x18
	Description
	Number of display buffers. To decode all frames in reverse playback you
	must use nine buffers.
	Param[0]
	0=six buffers, 1=nine buffers

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_EXTRACT_VBI
	Enum 25/0x19
	Description
	Extracts VBI data
	Param[0]
	0=extract from extension & user data, 1=extract from private packets
	Result[0]
	VBI table location
	Result[1]
	VBI table size

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_DECODER_SOURCE
	Enum 26/0x1A
	Description
	Selects decoder source. Ensure that the parameters passed to this
	API match the encoder settings.
	Param[0]
	Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
	Param[1]
	YUV picture width
	Param[2]
	YUV picture height
	Param[3]
	Bitmap: see Param[0] of API 0xBD

	-------------------------------------------------------------------------------

	Name CX2341X_DEC_SET_PREBUFFERING
	Enum 30/0x1E
	Description
	Decoder prebuffering, when enabled up to 128KB are buffered for
	streams <8mpbs or 640KB for streams >8mbps
	Param[0]
	0=off, 1=on