| /* |
| * Freescale STMP378X SPI master driver |
| * |
| * Author: dmitry pervushin <dimka@embeddedalley.com> |
| * |
| * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved. |
| * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved. |
| */ |
| |
| /* |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/platform_device.h> |
| #include <linux/spi/spi.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/io.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/delay.h> |
| |
| #include <mach/platform.h> |
| #include <mach/stmp3xxx.h> |
| #include <mach/dma.h> |
| #include <mach/regs-ssp.h> |
| #include <mach/regs-apbh.h> |
| |
| |
| /* 0 means DMA mode(recommended, default), !0 - PIO mode */ |
| static int pio; |
| static int clock; |
| |
| /* default timeout for busy waits is 2 seconds */ |
| #define STMP_SPI_TIMEOUT (2 * HZ) |
| |
| struct stmp_spi { |
| int id; |
| |
| void * __iomem regs; /* vaddr of the control registers */ |
| |
| int irq, err_irq; |
| u32 dma; |
| struct stmp3xxx_dma_descriptor d; |
| |
| u32 speed_khz; |
| u32 saved_timings; |
| u32 divider; |
| |
| struct clk *clk; |
| struct device *master_dev; |
| |
| struct work_struct work; |
| struct workqueue_struct *workqueue; |
| |
| /* lock protects queue access */ |
| spinlock_t lock; |
| struct list_head queue; |
| |
| struct completion done; |
| }; |
| |
| #define busy_wait(cond) \ |
| ({ \ |
| unsigned long end_jiffies = jiffies + STMP_SPI_TIMEOUT; \ |
| bool succeeded = false; \ |
| do { \ |
| if (cond) { \ |
| succeeded = true; \ |
| break; \ |
| } \ |
| cpu_relax(); \ |
| } while (time_before(jiffies, end_jiffies)); \ |
| succeeded; \ |
| }) |
| |
| /** |
| * stmp_spi_init_hw |
| * Initialize the SSP port |
| */ |
| static int stmp_spi_init_hw(struct stmp_spi *ss) |
| { |
| int err = 0; |
| void *pins = ss->master_dev->platform_data; |
| |
| err = stmp3xxx_request_pin_group(pins, dev_name(ss->master_dev)); |
| if (err) |
| goto out; |
| |
| ss->clk = clk_get(NULL, "ssp"); |
| if (IS_ERR(ss->clk)) { |
| err = PTR_ERR(ss->clk); |
| goto out_free_pins; |
| } |
| clk_enable(ss->clk); |
| |
| stmp3xxx_reset_block(ss->regs, false); |
| stmp3xxx_dma_reset_channel(ss->dma); |
| |
| return 0; |
| |
| out_free_pins: |
| stmp3xxx_release_pin_group(pins, dev_name(ss->master_dev)); |
| out: |
| return err; |
| } |
| |
| static void stmp_spi_release_hw(struct stmp_spi *ss) |
| { |
| void *pins = ss->master_dev->platform_data; |
| |
| if (ss->clk && !IS_ERR(ss->clk)) { |
| clk_disable(ss->clk); |
| clk_put(ss->clk); |
| } |
| stmp3xxx_release_pin_group(pins, dev_name(ss->master_dev)); |
| } |
| |
| static int stmp_spi_setup_transfer(struct spi_device *spi, |
| struct spi_transfer *t) |
| { |
| u8 bits_per_word; |
| u32 hz; |
| struct stmp_spi *ss = spi_master_get_devdata(spi->master); |
| u16 rate; |
| |
| bits_per_word = spi->bits_per_word; |
| if (t && t->bits_per_word) |
| bits_per_word = t->bits_per_word; |
| |
| /* |
| * Calculate speed: |
| * - by default, use maximum speed from ssp clk |
| * - if device overrides it, use it |
| * - if transfer specifies other speed, use transfer's one |
| */ |
| hz = 1000 * ss->speed_khz / ss->divider; |
| if (spi->max_speed_hz) |
| hz = min(hz, spi->max_speed_hz); |
| if (t && t->speed_hz) |
| hz = min(hz, t->speed_hz); |
| |
| if (hz == 0) { |
| dev_err(&spi->dev, "Cannot continue with zero clock\n"); |
| return -EINVAL; |
| } |
| |
| if (bits_per_word != 8) { |
| dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", |
| __func__, bits_per_word); |
| return -EINVAL; |
| } |
| |
| dev_dbg(&spi->dev, "Requested clk rate = %uHz, max = %uHz/%d = %uHz\n", |
| hz, ss->speed_khz, ss->divider, |
| ss->speed_khz * 1000 / ss->divider); |
| |
| if (ss->speed_khz * 1000 / ss->divider < hz) { |
| dev_err(&spi->dev, "%s, unsupported clock rate %uHz\n", |
| __func__, hz); |
| return -EINVAL; |
| } |
| |
| rate = 1000 * ss->speed_khz/ss->divider/hz; |
| |
| writel(BF(ss->divider, SSP_TIMING_CLOCK_DIVIDE) | |
| BF(rate - 1, SSP_TIMING_CLOCK_RATE), |
| HW_SSP_TIMING + ss->regs); |
| |
| writel(BF(1 /* mode SPI */, SSP_CTRL1_SSP_MODE) | |
| BF(4 /* 8 bits */, SSP_CTRL1_WORD_LENGTH) | |
| ((spi->mode & SPI_CPOL) ? BM_SSP_CTRL1_POLARITY : 0) | |
| ((spi->mode & SPI_CPHA) ? BM_SSP_CTRL1_PHASE : 0) | |
| (pio ? 0 : BM_SSP_CTRL1_DMA_ENABLE), |
| ss->regs + HW_SSP_CTRL1); |
| |
| return 0; |
| } |
| |
| static int stmp_spi_setup(struct spi_device *spi) |
| { |
| /* spi_setup() does basic checks, |
| * stmp_spi_setup_transfer() does more later |
| */ |
| if (spi->bits_per_word != 8) { |
| dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", |
| __func__, spi->bits_per_word); |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static inline u32 stmp_spi_cs(unsigned cs) |
| { |
| return ((cs & 1) ? BM_SSP_CTRL0_WAIT_FOR_CMD : 0) | |
| ((cs & 2) ? BM_SSP_CTRL0_WAIT_FOR_IRQ : 0); |
| } |
| |
| static int stmp_spi_txrx_dma(struct stmp_spi *ss, int cs, |
| unsigned char *buf, dma_addr_t dma_buf, int len, |
| int first, int last, bool write) |
| { |
| u32 c0 = 0; |
| dma_addr_t spi_buf_dma = dma_buf; |
| int status = 0; |
| enum dma_data_direction dir = write ? DMA_TO_DEVICE : DMA_FROM_DEVICE; |
| |
| c0 |= (first ? BM_SSP_CTRL0_LOCK_CS : 0); |
| c0 |= (last ? BM_SSP_CTRL0_IGNORE_CRC : 0); |
| c0 |= (write ? 0 : BM_SSP_CTRL0_READ); |
| c0 |= BM_SSP_CTRL0_DATA_XFER; |
| |
| c0 |= stmp_spi_cs(cs); |
| |
| c0 |= BF(len, SSP_CTRL0_XFER_COUNT); |
| |
| if (!dma_buf) |
| spi_buf_dma = dma_map_single(ss->master_dev, buf, len, dir); |
| |
| ss->d.command->cmd = |
| BF(len, APBH_CHn_CMD_XFER_COUNT) | |
| BF(1, APBH_CHn_CMD_CMDWORDS) | |
| BM_APBH_CHn_CMD_WAIT4ENDCMD | |
| BM_APBH_CHn_CMD_IRQONCMPLT | |
| BF(write ? BV_APBH_CHn_CMD_COMMAND__DMA_READ : |
| BV_APBH_CHn_CMD_COMMAND__DMA_WRITE, |
| APBH_CHn_CMD_COMMAND); |
| ss->d.command->pio_words[0] = c0; |
| ss->d.command->buf_ptr = spi_buf_dma; |
| |
| stmp3xxx_dma_reset_channel(ss->dma); |
| stmp3xxx_dma_clear_interrupt(ss->dma); |
| stmp3xxx_dma_enable_interrupt(ss->dma); |
| init_completion(&ss->done); |
| stmp3xxx_dma_go(ss->dma, &ss->d, 1); |
| wait_for_completion(&ss->done); |
| |
| if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) & BM_SSP_CTRL0_RUN)) |
| status = -ETIMEDOUT; |
| |
| if (!dma_buf) |
| dma_unmap_single(ss->master_dev, spi_buf_dma, len, dir); |
| |
| return status; |
| } |
| |
| static inline void stmp_spi_enable(struct stmp_spi *ss) |
| { |
| stmp3xxx_setl(BM_SSP_CTRL0_LOCK_CS, ss->regs + HW_SSP_CTRL0); |
| stmp3xxx_clearl(BM_SSP_CTRL0_IGNORE_CRC, ss->regs + HW_SSP_CTRL0); |
| } |
| |
| static inline void stmp_spi_disable(struct stmp_spi *ss) |
| { |
| stmp3xxx_clearl(BM_SSP_CTRL0_LOCK_CS, ss->regs + HW_SSP_CTRL0); |
| stmp3xxx_setl(BM_SSP_CTRL0_IGNORE_CRC, ss->regs + HW_SSP_CTRL0); |
| } |
| |
| static int stmp_spi_txrx_pio(struct stmp_spi *ss, int cs, |
| unsigned char *buf, int len, |
| bool first, bool last, bool write) |
| { |
| if (first) |
| stmp_spi_enable(ss); |
| |
| stmp3xxx_setl(stmp_spi_cs(cs), ss->regs + HW_SSP_CTRL0); |
| |
| while (len--) { |
| if (last && len <= 0) |
| stmp_spi_disable(ss); |
| |
| stmp3xxx_clearl(BM_SSP_CTRL0_XFER_COUNT, |
| ss->regs + HW_SSP_CTRL0); |
| stmp3xxx_setl(1, ss->regs + HW_SSP_CTRL0); |
| |
| if (write) |
| stmp3xxx_clearl(BM_SSP_CTRL0_READ, |
| ss->regs + HW_SSP_CTRL0); |
| else |
| stmp3xxx_setl(BM_SSP_CTRL0_READ, |
| ss->regs + HW_SSP_CTRL0); |
| |
| /* Run! */ |
| stmp3xxx_setl(BM_SSP_CTRL0_RUN, ss->regs + HW_SSP_CTRL0); |
| |
| if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) & |
| BM_SSP_CTRL0_RUN)) |
| break; |
| |
| if (write) |
| writel(*buf, ss->regs + HW_SSP_DATA); |
| |
| /* Set TRANSFER */ |
| stmp3xxx_setl(BM_SSP_CTRL0_DATA_XFER, ss->regs + HW_SSP_CTRL0); |
| |
| if (!write) { |
| if (busy_wait((readl(ss->regs + HW_SSP_STATUS) & |
| BM_SSP_STATUS_FIFO_EMPTY))) |
| break; |
| *buf = readl(ss->regs + HW_SSP_DATA) & 0xFF; |
| } |
| |
| if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) & |
| BM_SSP_CTRL0_RUN)) |
| break; |
| |
| /* advance to the next byte */ |
| buf++; |
| } |
| |
| return len < 0 ? 0 : -ETIMEDOUT; |
| } |
| |
| static int stmp_spi_handle_message(struct stmp_spi *ss, struct spi_message *m) |
| { |
| bool first, last; |
| struct spi_transfer *t, *tmp_t; |
| int status = 0; |
| int cs; |
| |
| cs = m->spi->chip_select; |
| |
| list_for_each_entry_safe(t, tmp_t, &m->transfers, transfer_list) { |
| |
| first = (&t->transfer_list == m->transfers.next); |
| last = (&t->transfer_list == m->transfers.prev); |
| |
| if (first || t->speed_hz || t->bits_per_word) |
| stmp_spi_setup_transfer(m->spi, t); |
| |
| /* reject "not last" transfers which request to change cs */ |
| if (t->cs_change && !last) { |
| dev_err(&m->spi->dev, |
| "Message with t->cs_change has been skipped\n"); |
| continue; |
| } |
| |
| if (t->tx_buf) { |
| status = pio ? |
| stmp_spi_txrx_pio(ss, cs, (void *)t->tx_buf, |
| t->len, first, last, true) : |
| stmp_spi_txrx_dma(ss, cs, (void *)t->tx_buf, |
| t->tx_dma, t->len, first, last, true); |
| #ifdef DEBUG |
| if (t->len < 0x10) |
| print_hex_dump_bytes("Tx ", |
| DUMP_PREFIX_OFFSET, |
| t->tx_buf, t->len); |
| else |
| pr_debug("Tx: %d bytes\n", t->len); |
| #endif |
| } |
| if (t->rx_buf) { |
| status = pio ? |
| stmp_spi_txrx_pio(ss, cs, t->rx_buf, |
| t->len, first, last, false) : |
| stmp_spi_txrx_dma(ss, cs, t->rx_buf, |
| t->rx_dma, t->len, first, last, false); |
| #ifdef DEBUG |
| if (t->len < 0x10) |
| print_hex_dump_bytes("Rx ", |
| DUMP_PREFIX_OFFSET, |
| t->rx_buf, t->len); |
| else |
| pr_debug("Rx: %d bytes\n", t->len); |
| #endif |
| } |
| |
| if (t->delay_usecs) |
| udelay(t->delay_usecs); |
| |
| if (status) |
| break; |
| |
| } |
| return status; |
| } |
| |
| /** |
| * stmp_spi_handle - handle messages from the queue |
| */ |
| static void stmp_spi_handle(struct work_struct *w) |
| { |
| struct stmp_spi *ss = container_of(w, struct stmp_spi, work); |
| unsigned long flags; |
| struct spi_message *m; |
| |
| spin_lock_irqsave(&ss->lock, flags); |
| while (!list_empty(&ss->queue)) { |
| m = list_entry(ss->queue.next, struct spi_message, queue); |
| list_del_init(&m->queue); |
| spin_unlock_irqrestore(&ss->lock, flags); |
| |
| m->status = stmp_spi_handle_message(ss, m); |
| m->complete(m->context); |
| |
| spin_lock_irqsave(&ss->lock, flags); |
| } |
| spin_unlock_irqrestore(&ss->lock, flags); |
| |
| return; |
| } |
| |
| /** |
| * stmp_spi_transfer - perform message transfer. |
| * Called indirectly from spi_async, queues all the messages to |
| * spi_handle_message. |
| * @spi: spi device |
| * @m: message to be queued |
| */ |
| static int stmp_spi_transfer(struct spi_device *spi, struct spi_message *m) |
| { |
| struct stmp_spi *ss = spi_master_get_devdata(spi->master); |
| unsigned long flags; |
| |
| m->status = -EINPROGRESS; |
| spin_lock_irqsave(&ss->lock, flags); |
| list_add_tail(&m->queue, &ss->queue); |
| queue_work(ss->workqueue, &ss->work); |
| spin_unlock_irqrestore(&ss->lock, flags); |
| return 0; |
| } |
| |
| static irqreturn_t stmp_spi_irq(int irq, void *dev_id) |
| { |
| struct stmp_spi *ss = dev_id; |
| |
| stmp3xxx_dma_clear_interrupt(ss->dma); |
| complete(&ss->done); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t stmp_spi_irq_err(int irq, void *dev_id) |
| { |
| struct stmp_spi *ss = dev_id; |
| u32 c1, st; |
| |
| c1 = readl(ss->regs + HW_SSP_CTRL1); |
| st = readl(ss->regs + HW_SSP_STATUS); |
| dev_err(ss->master_dev, "%s: status = 0x%08X, c1 = 0x%08X\n", |
| __func__, st, c1); |
| stmp3xxx_clearl(c1 & 0xCCCC0000, ss->regs + HW_SSP_CTRL1); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int __devinit stmp_spi_probe(struct platform_device *dev) |
| { |
| int err = 0; |
| struct spi_master *master; |
| struct stmp_spi *ss; |
| struct resource *r; |
| |
| master = spi_alloc_master(&dev->dev, sizeof(struct stmp_spi)); |
| if (master == NULL) { |
| err = -ENOMEM; |
| goto out0; |
| } |
| master->flags = SPI_MASTER_HALF_DUPLEX; |
| |
| ss = spi_master_get_devdata(master); |
| platform_set_drvdata(dev, master); |
| |
| /* Get resources(memory, IRQ) associated with the device */ |
| r = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| if (r == NULL) { |
| err = -ENODEV; |
| goto out_put_master; |
| } |
| ss->regs = ioremap(r->start, resource_size(r)); |
| if (!ss->regs) { |
| err = -EINVAL; |
| goto out_put_master; |
| } |
| |
| ss->master_dev = &dev->dev; |
| ss->id = dev->id; |
| |
| INIT_WORK(&ss->work, stmp_spi_handle); |
| INIT_LIST_HEAD(&ss->queue); |
| spin_lock_init(&ss->lock); |
| |
| ss->workqueue = create_singlethread_workqueue(dev_name(&dev->dev)); |
| if (!ss->workqueue) { |
| err = -ENXIO; |
| goto out_put_master; |
| } |
| master->transfer = stmp_spi_transfer; |
| master->setup = stmp_spi_setup; |
| |
| /* the spi->mode bits understood by this driver: */ |
| master->mode_bits = SPI_CPOL | SPI_CPHA; |
| |
| ss->irq = platform_get_irq(dev, 0); |
| if (ss->irq < 0) { |
| err = ss->irq; |
| goto out_put_master; |
| } |
| ss->err_irq = platform_get_irq(dev, 1); |
| if (ss->err_irq < 0) { |
| err = ss->err_irq; |
| goto out_put_master; |
| } |
| |
| r = platform_get_resource(dev, IORESOURCE_DMA, 0); |
| if (r == NULL) { |
| err = -ENODEV; |
| goto out_put_master; |
| } |
| |
| ss->dma = r->start; |
| err = stmp3xxx_dma_request(ss->dma, &dev->dev, dev_name(&dev->dev)); |
| if (err) |
| goto out_put_master; |
| |
| err = stmp3xxx_dma_allocate_command(ss->dma, &ss->d); |
| if (err) |
| goto out_free_dma; |
| |
| master->bus_num = dev->id; |
| master->num_chipselect = 1; |
| |
| /* SPI controller initializations */ |
| err = stmp_spi_init_hw(ss); |
| if (err) { |
| dev_dbg(&dev->dev, "cannot initialize hardware\n"); |
| goto out_free_dma_desc; |
| } |
| |
| if (clock) { |
| dev_info(&dev->dev, "clock rate forced to %d\n", clock); |
| clk_set_rate(ss->clk, clock); |
| } |
| ss->speed_khz = clk_get_rate(ss->clk); |
| ss->divider = 2; |
| dev_info(&dev->dev, "max possible speed %d = %ld/%d kHz\n", |
| ss->speed_khz, clk_get_rate(ss->clk), ss->divider); |
| |
| /* Register for SPI interrupt */ |
| err = request_irq(ss->irq, stmp_spi_irq, 0, |
| dev_name(&dev->dev), ss); |
| if (err) { |
| dev_dbg(&dev->dev, "request_irq failed, %d\n", err); |
| goto out_release_hw; |
| } |
| |
| /* ..and shared interrupt for all SSP controllers */ |
| err = request_irq(ss->err_irq, stmp_spi_irq_err, IRQF_SHARED, |
| dev_name(&dev->dev), ss); |
| if (err) { |
| dev_dbg(&dev->dev, "request_irq(error) failed, %d\n", err); |
| goto out_free_irq; |
| } |
| |
| err = spi_register_master(master); |
| if (err) { |
| dev_dbg(&dev->dev, "cannot register spi master, %d\n", err); |
| goto out_free_irq_2; |
| } |
| dev_info(&dev->dev, "at (mapped) 0x%08X, irq=%d, bus %d, %s mode\n", |
| (u32)ss->regs, ss->irq, master->bus_num, |
| pio ? "PIO" : "DMA"); |
| return 0; |
| |
| out_free_irq_2: |
| free_irq(ss->err_irq, ss); |
| out_free_irq: |
| free_irq(ss->irq, ss); |
| out_free_dma_desc: |
| stmp3xxx_dma_free_command(ss->dma, &ss->d); |
| out_free_dma: |
| stmp3xxx_dma_release(ss->dma); |
| out_release_hw: |
| stmp_spi_release_hw(ss); |
| out_put_master: |
| if (ss->workqueue) |
| destroy_workqueue(ss->workqueue); |
| if (ss->regs) |
| iounmap(ss->regs); |
| platform_set_drvdata(dev, NULL); |
| spi_master_put(master); |
| out0: |
| return err; |
| } |
| |
| static int __devexit stmp_spi_remove(struct platform_device *dev) |
| { |
| struct stmp_spi *ss; |
| struct spi_master *master; |
| |
| master = platform_get_drvdata(dev); |
| if (master == NULL) |
| goto out0; |
| ss = spi_master_get_devdata(master); |
| |
| spi_unregister_master(master); |
| |
| free_irq(ss->err_irq, ss); |
| free_irq(ss->irq, ss); |
| stmp3xxx_dma_free_command(ss->dma, &ss->d); |
| stmp3xxx_dma_release(ss->dma); |
| stmp_spi_release_hw(ss); |
| destroy_workqueue(ss->workqueue); |
| iounmap(ss->regs); |
| spi_master_put(master); |
| platform_set_drvdata(dev, NULL); |
| out0: |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int stmp_spi_suspend(struct platform_device *pdev, pm_message_t pmsg) |
| { |
| struct stmp_spi *ss; |
| struct spi_master *master; |
| |
| master = platform_get_drvdata(pdev); |
| ss = spi_master_get_devdata(master); |
| |
| ss->saved_timings = readl(HW_SSP_TIMING + ss->regs); |
| clk_disable(ss->clk); |
| |
| return 0; |
| } |
| |
| static int stmp_spi_resume(struct platform_device *pdev) |
| { |
| struct stmp_spi *ss; |
| struct spi_master *master; |
| |
| master = platform_get_drvdata(pdev); |
| ss = spi_master_get_devdata(master); |
| |
| clk_enable(ss->clk); |
| stmp3xxx_reset_block(ss->regs, false); |
| writel(ss->saved_timings, ss->regs + HW_SSP_TIMING); |
| |
| return 0; |
| } |
| |
| #else |
| #define stmp_spi_suspend NULL |
| #define stmp_spi_resume NULL |
| #endif |
| |
| static struct platform_driver stmp_spi_driver = { |
| .probe = stmp_spi_probe, |
| .remove = __devexit_p(stmp_spi_remove), |
| .driver = { |
| .name = "stmp3xxx_ssp", |
| .owner = THIS_MODULE, |
| }, |
| .suspend = stmp_spi_suspend, |
| .resume = stmp_spi_resume, |
| }; |
| module_platform_driver(stmp_spi_driver); |
| |
| module_param(pio, int, S_IRUGO); |
| module_param(clock, int, S_IRUGO); |
| MODULE_AUTHOR("dmitry pervushin <dpervushin@embeddedalley.com>"); |
| MODULE_DESCRIPTION("STMP3xxx SPI/SSP driver"); |
| MODULE_LICENSE("GPL"); |