| /* |
| * Driver for Amlogic Meson SPI flash controller (SPIFC) |
| * |
| * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * version 2 as published by the Free Software Foundation. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program. If not, see <http://www.gnu.org/licenses/>. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regmap.h> |
| #include <linux/spi/spi.h> |
| #include <linux/types.h> |
| |
| /* register map */ |
| #define REG_CMD 0x00 |
| #define REG_ADDR 0x04 |
| #define REG_CTRL 0x08 |
| #define REG_CTRL1 0x0c |
| #define REG_STATUS 0x10 |
| #define REG_CTRL2 0x14 |
| #define REG_CLOCK 0x18 |
| #define REG_USER 0x1c |
| #define REG_USER1 0x20 |
| #define REG_USER2 0x24 |
| #define REG_USER3 0x28 |
| #define REG_USER4 0x2c |
| #define REG_SLAVE 0x30 |
| #define REG_SLAVE1 0x34 |
| #define REG_SLAVE2 0x38 |
| #define REG_SLAVE3 0x3c |
| #define REG_C0 0x40 |
| #define REG_B8 0x60 |
| #define REG_MAX 0x7c |
| |
| /* register fields */ |
| #define CMD_USER BIT(18) |
| #define CTRL_ENABLE_AHB BIT(17) |
| #define CLOCK_SOURCE BIT(31) |
| #define CLOCK_DIV_SHIFT 12 |
| #define CLOCK_DIV_MASK (0x3f << CLOCK_DIV_SHIFT) |
| #define CLOCK_CNT_HIGH_SHIFT 6 |
| #define CLOCK_CNT_HIGH_MASK (0x3f << CLOCK_CNT_HIGH_SHIFT) |
| #define CLOCK_CNT_LOW_SHIFT 0 |
| #define CLOCK_CNT_LOW_MASK (0x3f << CLOCK_CNT_LOW_SHIFT) |
| #define USER_DIN_EN_MS BIT(0) |
| #define USER_CMP_MODE BIT(2) |
| #define USER_UC_DOUT_SEL BIT(27) |
| #define USER_UC_DIN_SEL BIT(28) |
| #define USER_UC_MASK ((BIT(5) - 1) << 27) |
| #define USER1_BN_UC_DOUT_SHIFT 17 |
| #define USER1_BN_UC_DOUT_MASK (0xff << 16) |
| #define USER1_BN_UC_DIN_SHIFT 8 |
| #define USER1_BN_UC_DIN_MASK (0xff << 8) |
| #define USER4_CS_ACT BIT(30) |
| #define SLAVE_TRST_DONE BIT(4) |
| #define SLAVE_OP_MODE BIT(30) |
| #define SLAVE_SW_RST BIT(31) |
| |
| #define SPIFC_BUFFER_SIZE 64 |
| |
| /** |
| * struct meson_spifc |
| * @master: the SPI master |
| * @regmap: regmap for device registers |
| * @clk: input clock of the built-in baud rate generator |
| * @device: the device structure |
| */ |
| struct meson_spifc { |
| struct spi_master *master; |
| struct regmap *regmap; |
| struct clk *clk; |
| struct device *dev; |
| }; |
| |
| static struct regmap_config spifc_regmap_config = { |
| .reg_bits = 32, |
| .val_bits = 32, |
| .reg_stride = 4, |
| .max_register = REG_MAX, |
| }; |
| |
| /** |
| * meson_spifc_wait_ready() - wait for the current operation to terminate |
| * @spifc: the Meson SPI device |
| * Return: 0 on success, a negative value on error |
| */ |
| static int meson_spifc_wait_ready(struct meson_spifc *spifc) |
| { |
| unsigned long deadline = jiffies + msecs_to_jiffies(5); |
| u32 data; |
| |
| do { |
| regmap_read(spifc->regmap, REG_SLAVE, &data); |
| if (data & SLAVE_TRST_DONE) |
| return 0; |
| cond_resched(); |
| } while (!time_after(jiffies, deadline)); |
| |
| return -ETIMEDOUT; |
| } |
| |
| /** |
| * meson_spifc_drain_buffer() - copy data from device buffer to memory |
| * @spifc: the Meson SPI device |
| * @buf: the destination buffer |
| * @len: number of bytes to copy |
| */ |
| static void meson_spifc_drain_buffer(struct meson_spifc *spifc, u8 *buf, |
| int len) |
| { |
| u32 data; |
| int i = 0; |
| |
| while (i < len) { |
| regmap_read(spifc->regmap, REG_C0 + i, &data); |
| |
| if (len - i >= 4) { |
| *((u32 *)buf) = data; |
| buf += 4; |
| } else { |
| memcpy(buf, &data, len - i); |
| break; |
| } |
| i += 4; |
| } |
| } |
| |
| /** |
| * meson_spifc_fill_buffer() - copy data from memory to device buffer |
| * @spifc: the Meson SPI device |
| * @buf: the source buffer |
| * @len: number of bytes to copy |
| */ |
| static void meson_spifc_fill_buffer(struct meson_spifc *spifc, const u8 *buf, |
| int len) |
| { |
| u32 data; |
| int i = 0; |
| |
| while (i < len) { |
| if (len - i >= 4) |
| data = *(u32 *)buf; |
| else |
| memcpy(&data, buf, len - i); |
| |
| regmap_write(spifc->regmap, REG_C0 + i, data); |
| |
| buf += 4; |
| i += 4; |
| } |
| } |
| |
| /** |
| * meson_spifc_setup_speed() - program the clock divider |
| * @spifc: the Meson SPI device |
| * @speed: desired speed in Hz |
| */ |
| static void meson_spifc_setup_speed(struct meson_spifc *spifc, u32 speed) |
| { |
| unsigned long parent, value; |
| int n; |
| |
| parent = clk_get_rate(spifc->clk); |
| n = max_t(int, parent / speed - 1, 1); |
| |
| dev_dbg(spifc->dev, "parent %lu, speed %u, n %d\n", parent, |
| speed, n); |
| |
| value = (n << CLOCK_DIV_SHIFT) & CLOCK_DIV_MASK; |
| value |= (n << CLOCK_CNT_LOW_SHIFT) & CLOCK_CNT_LOW_MASK; |
| value |= (((n + 1) / 2 - 1) << CLOCK_CNT_HIGH_SHIFT) & |
| CLOCK_CNT_HIGH_MASK; |
| |
| regmap_write(spifc->regmap, REG_CLOCK, value); |
| } |
| |
| /** |
| * meson_spifc_txrx() - transfer a chunk of data |
| * @spifc: the Meson SPI device |
| * @xfer: the current SPI transfer |
| * @offset: offset of the data to transfer |
| * @len: length of the data to transfer |
| * @last_xfer: whether this is the last transfer of the message |
| * @last_chunk: whether this is the last chunk of the transfer |
| * Return: 0 on success, a negative value on error |
| */ |
| static int meson_spifc_txrx(struct meson_spifc *spifc, |
| struct spi_transfer *xfer, |
| int offset, int len, bool last_xfer, |
| bool last_chunk) |
| { |
| bool keep_cs = true; |
| int ret; |
| |
| if (xfer->tx_buf) |
| meson_spifc_fill_buffer(spifc, xfer->tx_buf + offset, len); |
| |
| /* enable DOUT stage */ |
| regmap_update_bits(spifc->regmap, REG_USER, USER_UC_MASK, |
| USER_UC_DOUT_SEL); |
| regmap_write(spifc->regmap, REG_USER1, |
| (8 * len - 1) << USER1_BN_UC_DOUT_SHIFT); |
| |
| /* enable data input during DOUT */ |
| regmap_update_bits(spifc->regmap, REG_USER, USER_DIN_EN_MS, |
| USER_DIN_EN_MS); |
| |
| if (last_chunk) { |
| if (last_xfer) |
| keep_cs = xfer->cs_change; |
| else |
| keep_cs = !xfer->cs_change; |
| } |
| |
| regmap_update_bits(spifc->regmap, REG_USER4, USER4_CS_ACT, |
| keep_cs ? USER4_CS_ACT : 0); |
| |
| /* clear transition done bit */ |
| regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_TRST_DONE, 0); |
| /* start transfer */ |
| regmap_update_bits(spifc->regmap, REG_CMD, CMD_USER, CMD_USER); |
| |
| ret = meson_spifc_wait_ready(spifc); |
| |
| if (!ret && xfer->rx_buf) |
| meson_spifc_drain_buffer(spifc, xfer->rx_buf + offset, len); |
| |
| return ret; |
| } |
| |
| /** |
| * meson_spifc_transfer_one() - perform a single transfer |
| * @master: the SPI master |
| * @spi: the SPI device |
| * @xfer: the current SPI transfer |
| * Return: 0 on success, a negative value on error |
| */ |
| static int meson_spifc_transfer_one(struct spi_master *master, |
| struct spi_device *spi, |
| struct spi_transfer *xfer) |
| { |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| int len, done = 0, ret = 0; |
| |
| meson_spifc_setup_speed(spifc, xfer->speed_hz); |
| |
| regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, 0); |
| |
| while (done < xfer->len && !ret) { |
| len = min_t(int, xfer->len - done, SPIFC_BUFFER_SIZE); |
| ret = meson_spifc_txrx(spifc, xfer, done, len, |
| spi_transfer_is_last(master, xfer), |
| done + len >= xfer->len); |
| done += len; |
| } |
| |
| regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, |
| CTRL_ENABLE_AHB); |
| |
| return ret; |
| } |
| |
| /** |
| * meson_spifc_hw_init() - reset and initialize the SPI controller |
| * @spifc: the Meson SPI device |
| */ |
| static void meson_spifc_hw_init(struct meson_spifc *spifc) |
| { |
| /* reset device */ |
| regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_SW_RST, |
| SLAVE_SW_RST); |
| /* disable compatible mode */ |
| regmap_update_bits(spifc->regmap, REG_USER, USER_CMP_MODE, 0); |
| /* set master mode */ |
| regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_OP_MODE, 0); |
| } |
| |
| static int meson_spifc_probe(struct platform_device *pdev) |
| { |
| struct spi_master *master; |
| struct meson_spifc *spifc; |
| struct resource *res; |
| void __iomem *base; |
| unsigned int rate; |
| int ret = 0; |
| |
| master = spi_alloc_master(&pdev->dev, sizeof(struct meson_spifc)); |
| if (!master) |
| return -ENOMEM; |
| |
| platform_set_drvdata(pdev, master); |
| |
| spifc = spi_master_get_devdata(master); |
| spifc->dev = &pdev->dev; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| base = devm_ioremap_resource(spifc->dev, res); |
| if (IS_ERR(base)) { |
| ret = PTR_ERR(base); |
| goto out_err; |
| } |
| |
| spifc->regmap = devm_regmap_init_mmio(spifc->dev, base, |
| &spifc_regmap_config); |
| if (IS_ERR(spifc->regmap)) { |
| ret = PTR_ERR(spifc->regmap); |
| goto out_err; |
| } |
| |
| spifc->clk = devm_clk_get(spifc->dev, NULL); |
| if (IS_ERR(spifc->clk)) { |
| dev_err(spifc->dev, "missing clock\n"); |
| ret = PTR_ERR(spifc->clk); |
| goto out_err; |
| } |
| |
| ret = clk_prepare_enable(spifc->clk); |
| if (ret) { |
| dev_err(spifc->dev, "can't prepare clock\n"); |
| goto out_err; |
| } |
| |
| rate = clk_get_rate(spifc->clk); |
| |
| master->num_chipselect = 1; |
| master->dev.of_node = pdev->dev.of_node; |
| master->bits_per_word_mask = SPI_BPW_MASK(8); |
| master->auto_runtime_pm = true; |
| master->transfer_one = meson_spifc_transfer_one; |
| master->min_speed_hz = rate >> 6; |
| master->max_speed_hz = rate >> 1; |
| |
| meson_spifc_hw_init(spifc); |
| |
| pm_runtime_set_active(spifc->dev); |
| pm_runtime_enable(spifc->dev); |
| |
| ret = devm_spi_register_master(spifc->dev, master); |
| if (ret) { |
| dev_err(spifc->dev, "failed to register spi master\n"); |
| goto out_clk; |
| } |
| |
| return 0; |
| out_clk: |
| clk_disable_unprepare(spifc->clk); |
| out_err: |
| spi_master_put(master); |
| return ret; |
| } |
| |
| static int meson_spifc_remove(struct platform_device *pdev) |
| { |
| struct spi_master *master = platform_get_drvdata(pdev); |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| |
| pm_runtime_get_sync(&pdev->dev); |
| clk_disable_unprepare(spifc->clk); |
| pm_runtime_disable(&pdev->dev); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int meson_spifc_suspend(struct device *dev) |
| { |
| struct spi_master *master = dev_get_drvdata(dev); |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| int ret; |
| |
| ret = spi_master_suspend(master); |
| if (ret) |
| return ret; |
| |
| if (!pm_runtime_suspended(dev)) |
| clk_disable_unprepare(spifc->clk); |
| |
| return 0; |
| } |
| |
| static int meson_spifc_resume(struct device *dev) |
| { |
| struct spi_master *master = dev_get_drvdata(dev); |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| int ret; |
| |
| if (!pm_runtime_suspended(dev)) { |
| ret = clk_prepare_enable(spifc->clk); |
| if (ret) |
| return ret; |
| } |
| |
| meson_spifc_hw_init(spifc); |
| |
| ret = spi_master_resume(master); |
| if (ret) |
| clk_disable_unprepare(spifc->clk); |
| |
| return ret; |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| #ifdef CONFIG_PM |
| static int meson_spifc_runtime_suspend(struct device *dev) |
| { |
| struct spi_master *master = dev_get_drvdata(dev); |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| |
| clk_disable_unprepare(spifc->clk); |
| |
| return 0; |
| } |
| |
| static int meson_spifc_runtime_resume(struct device *dev) |
| { |
| struct spi_master *master = dev_get_drvdata(dev); |
| struct meson_spifc *spifc = spi_master_get_devdata(master); |
| |
| return clk_prepare_enable(spifc->clk); |
| } |
| #endif /* CONFIG_PM */ |
| |
| static const struct dev_pm_ops meson_spifc_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(meson_spifc_suspend, meson_spifc_resume) |
| SET_RUNTIME_PM_OPS(meson_spifc_runtime_suspend, |
| meson_spifc_runtime_resume, |
| NULL) |
| }; |
| |
| static const struct of_device_id meson_spifc_dt_match[] = { |
| { .compatible = "amlogic,meson6-spifc", }, |
| { }, |
| }; |
| |
| static struct platform_driver meson_spifc_driver = { |
| .probe = meson_spifc_probe, |
| .remove = meson_spifc_remove, |
| .driver = { |
| .name = "meson-spifc", |
| .of_match_table = of_match_ptr(meson_spifc_dt_match), |
| .pm = &meson_spifc_pm_ops, |
| }, |
| }; |
| |
| module_platform_driver(meson_spifc_driver); |
| |
| MODULE_AUTHOR("Beniamino Galvani <b.galvani@gmail.com>"); |
| MODULE_DESCRIPTION("Amlogic Meson SPIFC driver"); |
| MODULE_LICENSE("GPL v2"); |