blob: 83c2c727d71efb6095469ff75b561add90fb3b85 [file] [log] [blame]
#ifndef __NET_CFG80211_H
#define __NET_CFG80211_H
/*
* 802.11 device and configuration interface
*
* Copyright 2006-2009 Johannes Berg <johannes@sipsolutions.net>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/netdevice.h>
#include <linux/debugfs.h>
#include <linux/list.h>
#include <linux/netlink.h>
#include <linux/skbuff.h>
#include <linux/nl80211.h>
#include <linux/if_ether.h>
#include <linux/ieee80211.h>
#include <net/regulatory.h>
/* remove once we remove the wext stuff */
#include <net/iw_handler.h>
#include <linux/wireless.h>
/*
* wireless hardware capability structures
*/
/**
* enum ieee80211_band - supported frequency bands
*
* The bands are assigned this way because the supported
* bitrates differ in these bands.
*
* @IEEE80211_BAND_2GHZ: 2.4GHz ISM band
* @IEEE80211_BAND_5GHZ: around 5GHz band (4.9-5.7)
*/
enum ieee80211_band {
IEEE80211_BAND_2GHZ,
IEEE80211_BAND_5GHZ,
/* keep last */
IEEE80211_NUM_BANDS
};
/**
* enum ieee80211_channel_flags - channel flags
*
* Channel flags set by the regulatory control code.
*
* @IEEE80211_CHAN_DISABLED: This channel is disabled.
* @IEEE80211_CHAN_PASSIVE_SCAN: Only passive scanning is permitted
* on this channel.
* @IEEE80211_CHAN_NO_IBSS: IBSS is not allowed on this channel.
* @IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
* @IEEE80211_CHAN_NO_HT40PLUS: extension channel above this channel
* is not permitted.
* @IEEE80211_CHAN_NO_HT40MINUS: extension channel below this channel
* is not permitted.
*/
enum ieee80211_channel_flags {
IEEE80211_CHAN_DISABLED = 1<<0,
IEEE80211_CHAN_PASSIVE_SCAN = 1<<1,
IEEE80211_CHAN_NO_IBSS = 1<<2,
IEEE80211_CHAN_RADAR = 1<<3,
IEEE80211_CHAN_NO_HT40PLUS = 1<<4,
IEEE80211_CHAN_NO_HT40MINUS = 1<<5,
};
#define IEEE80211_CHAN_NO_HT40 \
(IEEE80211_CHAN_NO_HT40PLUS | IEEE80211_CHAN_NO_HT40MINUS)
/**
* struct ieee80211_channel - channel definition
*
* This structure describes a single channel for use
* with cfg80211.
*
* @center_freq: center frequency in MHz
* @max_bandwidth: maximum allowed bandwidth for this channel, in MHz
* @hw_value: hardware-specific value for the channel
* @flags: channel flags from &enum ieee80211_channel_flags.
* @orig_flags: channel flags at registration time, used by regulatory
* code to support devices with additional restrictions
* @band: band this channel belongs to.
* @max_antenna_gain: maximum antenna gain in dBi
* @max_power: maximum transmission power (in dBm)
* @beacon_found: helper to regulatory code to indicate when a beacon
* has been found on this channel. Use regulatory_hint_found_beacon()
* to enable this, this is is useful only on 5 GHz band.
* @orig_mag: internal use
* @orig_mpwr: internal use
*/
struct ieee80211_channel {
enum ieee80211_band band;
u16 center_freq;
u8 max_bandwidth;
u16 hw_value;
u32 flags;
int max_antenna_gain;
int max_power;
bool beacon_found;
u32 orig_flags;
int orig_mag, orig_mpwr;
};
/**
* enum ieee80211_rate_flags - rate flags
*
* Hardware/specification flags for rates. These are structured
* in a way that allows using the same bitrate structure for
* different bands/PHY modes.
*
* @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short
* preamble on this bitrate; only relevant in 2.4GHz band and
* with CCK rates.
* @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate
* when used with 802.11a (on the 5 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate
* when used with 802.11b (on the 2.4 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate
* when used with 802.11g (on the 2.4 GHz band); filled by the
* core code when registering the wiphy.
* @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode.
*/
enum ieee80211_rate_flags {
IEEE80211_RATE_SHORT_PREAMBLE = 1<<0,
IEEE80211_RATE_MANDATORY_A = 1<<1,
IEEE80211_RATE_MANDATORY_B = 1<<2,
IEEE80211_RATE_MANDATORY_G = 1<<3,
IEEE80211_RATE_ERP_G = 1<<4,
};
/**
* struct ieee80211_rate - bitrate definition
*
* This structure describes a bitrate that an 802.11 PHY can
* operate with. The two values @hw_value and @hw_value_short
* are only for driver use when pointers to this structure are
* passed around.
*
* @flags: rate-specific flags
* @bitrate: bitrate in units of 100 Kbps
* @hw_value: driver/hardware value for this rate
* @hw_value_short: driver/hardware value for this rate when
* short preamble is used
*/
struct ieee80211_rate {
u32 flags;
u16 bitrate;
u16 hw_value, hw_value_short;
};
/**
* struct ieee80211_sta_ht_cap - STA's HT capabilities
*
* This structure describes most essential parameters needed
* to describe 802.11n HT capabilities for an STA.
*
* @ht_supported: is HT supported by the STA
* @cap: HT capabilities map as described in 802.11n spec
* @ampdu_factor: Maximum A-MPDU length factor
* @ampdu_density: Minimum A-MPDU spacing
* @mcs: Supported MCS rates
*/
struct ieee80211_sta_ht_cap {
u16 cap; /* use IEEE80211_HT_CAP_ */
bool ht_supported;
u8 ampdu_factor;
u8 ampdu_density;
struct ieee80211_mcs_info mcs;
};
/**
* struct ieee80211_supported_band - frequency band definition
*
* This structure describes a frequency band a wiphy
* is able to operate in.
*
* @channels: Array of channels the hardware can operate in
* in this band.
* @band: the band this structure represents
* @n_channels: Number of channels in @channels
* @bitrates: Array of bitrates the hardware can operate with
* in this band. Must be sorted to give a valid "supported
* rates" IE, i.e. CCK rates first, then OFDM.
* @n_bitrates: Number of bitrates in @bitrates
*/
struct ieee80211_supported_band {
struct ieee80211_channel *channels;
struct ieee80211_rate *bitrates;
enum ieee80211_band band;
int n_channels;
int n_bitrates;
struct ieee80211_sta_ht_cap ht_cap;
};
/*
* Wireless hardware/device configuration structures and methods
*/
/**
* struct vif_params - describes virtual interface parameters
* @mesh_id: mesh ID to use
* @mesh_id_len: length of the mesh ID
*/
struct vif_params {
u8 *mesh_id;
int mesh_id_len;
};
/**
* struct key_params - key information
*
* Information about a key
*
* @key: key material
* @key_len: length of key material
* @cipher: cipher suite selector
* @seq: sequence counter (IV/PN) for TKIP and CCMP keys, only used
* with the get_key() callback, must be in little endian,
* length given by @seq_len.
*/
struct key_params {
u8 *key;
u8 *seq;
int key_len;
int seq_len;
u32 cipher;
};
/**
* struct beacon_parameters - beacon parameters
*
* Used to configure the beacon for an interface.
*
* @head: head portion of beacon (before TIM IE)
* or %NULL if not changed
* @tail: tail portion of beacon (after TIM IE)
* or %NULL if not changed
* @interval: beacon interval or zero if not changed
* @dtim_period: DTIM period or zero if not changed
* @head_len: length of @head
* @tail_len: length of @tail
*/
struct beacon_parameters {
u8 *head, *tail;
int interval, dtim_period;
int head_len, tail_len;
};
/**
* enum plink_action - actions to perform in mesh peers
*
* @PLINK_ACTION_INVALID: action 0 is reserved
* @PLINK_ACTION_OPEN: start mesh peer link establishment
* @PLINK_ACTION_BLOCL: block traffic from this mesh peer
*/
enum plink_actions {
PLINK_ACTION_INVALID,
PLINK_ACTION_OPEN,
PLINK_ACTION_BLOCK,
};
/**
* struct station_parameters - station parameters
*
* Used to change and create a new station.
*
* @vlan: vlan interface station should belong to
* @supported_rates: supported rates in IEEE 802.11 format
* (or NULL for no change)
* @supported_rates_len: number of supported rates
* @sta_flags_mask: station flags that changed
* (bitmask of BIT(NL80211_STA_FLAG_...))
* @sta_flags_set: station flags values
* (bitmask of BIT(NL80211_STA_FLAG_...))
* @listen_interval: listen interval or -1 for no change
* @aid: AID or zero for no change
*/
struct station_parameters {
u8 *supported_rates;
struct net_device *vlan;
u32 sta_flags_mask, sta_flags_set;
int listen_interval;
u16 aid;
u8 supported_rates_len;
u8 plink_action;
struct ieee80211_ht_cap *ht_capa;
};
/**
* enum station_info_flags - station information flags
*
* Used by the driver to indicate which info in &struct station_info
* it has filled in during get_station() or dump_station().
*
* @STATION_INFO_INACTIVE_TIME: @inactive_time filled
* @STATION_INFO_RX_BYTES: @rx_bytes filled
* @STATION_INFO_TX_BYTES: @tx_bytes filled
* @STATION_INFO_LLID: @llid filled
* @STATION_INFO_PLID: @plid filled
* @STATION_INFO_PLINK_STATE: @plink_state filled
* @STATION_INFO_SIGNAL: @signal filled
* @STATION_INFO_TX_BITRATE: @tx_bitrate fields are filled
* (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
* @STATION_INFO_RX_PACKETS: @rx_packets filled
* @STATION_INFO_TX_PACKETS: @tx_packets filled
*/
enum station_info_flags {
STATION_INFO_INACTIVE_TIME = 1<<0,
STATION_INFO_RX_BYTES = 1<<1,
STATION_INFO_TX_BYTES = 1<<2,
STATION_INFO_LLID = 1<<3,
STATION_INFO_PLID = 1<<4,
STATION_INFO_PLINK_STATE = 1<<5,
STATION_INFO_SIGNAL = 1<<6,
STATION_INFO_TX_BITRATE = 1<<7,
STATION_INFO_RX_PACKETS = 1<<8,
STATION_INFO_TX_PACKETS = 1<<9,
};
/**
* enum station_info_rate_flags - bitrate info flags
*
* Used by the driver to indicate the specific rate transmission
* type for 802.11n transmissions.
*
* @RATE_INFO_FLAGS_MCS: @tx_bitrate_mcs filled
* @RATE_INFO_FLAGS_40_MHZ_WIDTH: 40 Mhz width transmission
* @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
*/
enum rate_info_flags {
RATE_INFO_FLAGS_MCS = 1<<0,
RATE_INFO_FLAGS_40_MHZ_WIDTH = 1<<1,
RATE_INFO_FLAGS_SHORT_GI = 1<<2,
};
/**
* struct rate_info - bitrate information
*
* Information about a receiving or transmitting bitrate
*
* @flags: bitflag of flags from &enum rate_info_flags
* @mcs: mcs index if struct describes a 802.11n bitrate
* @legacy: bitrate in 100kbit/s for 802.11abg
*/
struct rate_info {
u8 flags;
u8 mcs;
u16 legacy;
};
/**
* struct station_info - station information
*
* Station information filled by driver for get_station() and dump_station.
*
* @filled: bitflag of flags from &enum station_info_flags
* @inactive_time: time since last station activity (tx/rx) in milliseconds
* @rx_bytes: bytes received from this station
* @tx_bytes: bytes transmitted to this station
* @llid: mesh local link id
* @plid: mesh peer link id
* @plink_state: mesh peer link state
* @signal: signal strength of last received packet in dBm
* @txrate: current unicast bitrate to this station
* @rx_packets: packets received from this station
* @tx_packets: packets transmitted to this station
*/
struct station_info {
u32 filled;
u32 inactive_time;
u32 rx_bytes;
u32 tx_bytes;
u16 llid;
u16 plid;
u8 plink_state;
s8 signal;
struct rate_info txrate;
u32 rx_packets;
u32 tx_packets;
};
/**
* enum monitor_flags - monitor flags
*
* Monitor interface configuration flags. Note that these must be the bits
* according to the nl80211 flags.
*
* @MONITOR_FLAG_FCSFAIL: pass frames with bad FCS
* @MONITOR_FLAG_PLCPFAIL: pass frames with bad PLCP
* @MONITOR_FLAG_CONTROL: pass control frames
* @MONITOR_FLAG_OTHER_BSS: disable BSSID filtering
* @MONITOR_FLAG_COOK_FRAMES: report frames after processing
*/
enum monitor_flags {
MONITOR_FLAG_FCSFAIL = 1<<NL80211_MNTR_FLAG_FCSFAIL,
MONITOR_FLAG_PLCPFAIL = 1<<NL80211_MNTR_FLAG_PLCPFAIL,
MONITOR_FLAG_CONTROL = 1<<NL80211_MNTR_FLAG_CONTROL,
MONITOR_FLAG_OTHER_BSS = 1<<NL80211_MNTR_FLAG_OTHER_BSS,
MONITOR_FLAG_COOK_FRAMES = 1<<NL80211_MNTR_FLAG_COOK_FRAMES,
};
/**
* enum mpath_info_flags - mesh path information flags
*
* Used by the driver to indicate which info in &struct mpath_info it has filled
* in during get_station() or dump_station().
*
* MPATH_INFO_FRAME_QLEN: @frame_qlen filled
* MPATH_INFO_DSN: @dsn filled
* MPATH_INFO_METRIC: @metric filled
* MPATH_INFO_EXPTIME: @exptime filled
* MPATH_INFO_DISCOVERY_TIMEOUT: @discovery_timeout filled
* MPATH_INFO_DISCOVERY_RETRIES: @discovery_retries filled
* MPATH_INFO_FLAGS: @flags filled
*/
enum mpath_info_flags {
MPATH_INFO_FRAME_QLEN = BIT(0),
MPATH_INFO_DSN = BIT(1),
MPATH_INFO_METRIC = BIT(2),
MPATH_INFO_EXPTIME = BIT(3),
MPATH_INFO_DISCOVERY_TIMEOUT = BIT(4),
MPATH_INFO_DISCOVERY_RETRIES = BIT(5),
MPATH_INFO_FLAGS = BIT(6),
};
/**
* struct mpath_info - mesh path information
*
* Mesh path information filled by driver for get_mpath() and dump_mpath().
*
* @filled: bitfield of flags from &enum mpath_info_flags
* @frame_qlen: number of queued frames for this destination
* @dsn: destination sequence number
* @metric: metric (cost) of this mesh path
* @exptime: expiration time for the mesh path from now, in msecs
* @flags: mesh path flags
* @discovery_timeout: total mesh path discovery timeout, in msecs
* @discovery_retries: mesh path discovery retries
*/
struct mpath_info {
u32 filled;
u32 frame_qlen;
u32 dsn;
u32 metric;
u32 exptime;
u32 discovery_timeout;
u8 discovery_retries;
u8 flags;
};
/**
* struct bss_parameters - BSS parameters
*
* Used to change BSS parameters (mainly for AP mode).
*
* @use_cts_prot: Whether to use CTS protection
* (0 = no, 1 = yes, -1 = do not change)
* @use_short_preamble: Whether the use of short preambles is allowed
* (0 = no, 1 = yes, -1 = do not change)
* @use_short_slot_time: Whether the use of short slot time is allowed
* (0 = no, 1 = yes, -1 = do not change)
* @basic_rates: basic rates in IEEE 802.11 format
* (or NULL for no change)
* @basic_rates_len: number of basic rates
*/
struct bss_parameters {
int use_cts_prot;
int use_short_preamble;
int use_short_slot_time;
u8 *basic_rates;
u8 basic_rates_len;
};
struct mesh_config {
/* Timeouts in ms */
/* Mesh plink management parameters */
u16 dot11MeshRetryTimeout;
u16 dot11MeshConfirmTimeout;
u16 dot11MeshHoldingTimeout;
u16 dot11MeshMaxPeerLinks;
u8 dot11MeshMaxRetries;
u8 dot11MeshTTL;
bool auto_open_plinks;
/* HWMP parameters */
u8 dot11MeshHWMPmaxPREQretries;
u32 path_refresh_time;
u16 min_discovery_timeout;
u32 dot11MeshHWMPactivePathTimeout;
u16 dot11MeshHWMPpreqMinInterval;
u16 dot11MeshHWMPnetDiameterTraversalTime;
};
/**
* struct ieee80211_txq_params - TX queue parameters
* @queue: TX queue identifier (NL80211_TXQ_Q_*)
* @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
* @cwmin: Minimum contention window [a value of the form 2^n-1 in the range
* 1..32767]
* @cwmax: Maximum contention window [a value of the form 2^n-1 in the range
* 1..32767]
* @aifs: Arbitration interframe space [0..255]
*/
struct ieee80211_txq_params {
enum nl80211_txq_q queue;
u16 txop;
u16 cwmin;
u16 cwmax;
u8 aifs;
};
/* from net/wireless.h */
struct wiphy;
/* from net/ieee80211.h */
struct ieee80211_channel;
/**
* struct cfg80211_ssid - SSID description
* @ssid: the SSID
* @ssid_len: length of the ssid
*/
struct cfg80211_ssid {
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 ssid_len;
};
/**
* struct cfg80211_scan_request - scan request description
*
* @ssids: SSIDs to scan for (active scan only)
* @n_ssids: number of SSIDs
* @channels: channels to scan on.
* @n_channels: number of channels for each band
* @ie: optional information element(s) to add into Probe Request or %NULL
* @ie_len: length of ie in octets
* @wiphy: the wiphy this was for
* @ifidx: the interface index
*/
struct cfg80211_scan_request {
struct cfg80211_ssid *ssids;
int n_ssids;
struct ieee80211_channel **channels;
u32 n_channels;
const u8 *ie;
size_t ie_len;
/* internal */
struct wiphy *wiphy;
int ifidx;
bool aborted;
};
/**
* enum cfg80211_signal_type - signal type
*
* @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available
* @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm)
* @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100
*/
enum cfg80211_signal_type {
CFG80211_SIGNAL_TYPE_NONE,
CFG80211_SIGNAL_TYPE_MBM,
CFG80211_SIGNAL_TYPE_UNSPEC,
};
/**
* struct cfg80211_bss - BSS description
*
* This structure describes a BSS (which may also be a mesh network)
* for use in scan results and similar.
*
* @bssid: BSSID of the BSS
* @tsf: timestamp of last received update
* @beacon_interval: the beacon interval as from the frame
* @capability: the capability field in host byte order
* @information_elements: the information elements (Note that there
* is no guarantee that these are well-formed!)
* @len_information_elements: total length of the information elements
* @signal: signal strength value (type depends on the wiphy's signal_type)
* @free_priv: function pointer to free private data
* @priv: private area for driver use, has at least wiphy->bss_priv_size bytes
*/
struct cfg80211_bss {
struct ieee80211_channel *channel;
u8 bssid[ETH_ALEN];
u64 tsf;
u16 beacon_interval;
u16 capability;
u8 *information_elements;
size_t len_information_elements;
s32 signal;
void (*free_priv)(struct cfg80211_bss *bss);
u8 priv[0] __attribute__((__aligned__(sizeof(void *))));
};
/**
* ieee80211_bss_get_ie - find IE with given ID
* @bss: the bss to search
* @ie: the IE ID
* Returns %NULL if not found.
*/
const u8 *ieee80211_bss_get_ie(struct cfg80211_bss *bss, u8 ie);
/**
* struct cfg80211_crypto_settings - Crypto settings
* @wpa_versions: indicates which, if any, WPA versions are enabled
* (from enum nl80211_wpa_versions)
* @cipher_group: group key cipher suite (or 0 if unset)
* @n_ciphers_pairwise: number of AP supported unicast ciphers
* @ciphers_pairwise: unicast key cipher suites
* @n_akm_suites: number of AKM suites
* @akm_suites: AKM suites
* @control_port: Whether user space controls IEEE 802.1X port, i.e.,
* sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is
* required to assume that the port is unauthorized until authorized by
* user space. Otherwise, port is marked authorized by default.
*/
struct cfg80211_crypto_settings {
u32 wpa_versions;
u32 cipher_group;
int n_ciphers_pairwise;
u32 ciphers_pairwise[NL80211_MAX_NR_CIPHER_SUITES];
int n_akm_suites;
u32 akm_suites[NL80211_MAX_NR_AKM_SUITES];
bool control_port;
};
/**
* struct cfg80211_auth_request - Authentication request data
*
* This structure provides information needed to complete IEEE 802.11
* authentication.
*
* @bss: The BSS to authenticate with.
* @auth_type: Authentication type (algorithm)
* @ie: Extra IEs to add to Authentication frame or %NULL
* @ie_len: Length of ie buffer in octets
*/
struct cfg80211_auth_request {
struct cfg80211_bss *bss;
const u8 *ie;
size_t ie_len;
enum nl80211_auth_type auth_type;
};
/**
* struct cfg80211_assoc_request - (Re)Association request data
*
* This structure provides information needed to complete IEEE 802.11
* (re)association.
* @bss: The BSS to associate with.
* @ie: Extra IEs to add to (Re)Association Request frame or %NULL
* @ie_len: Length of ie buffer in octets
* @use_mfp: Use management frame protection (IEEE 802.11w) in this association
* @crypto: crypto settings
* @prev_bssid: previous BSSID, if not %NULL use reassociate frame
*/
struct cfg80211_assoc_request {
struct cfg80211_bss *bss;
const u8 *ie, *prev_bssid;
size_t ie_len;
struct cfg80211_crypto_settings crypto;
bool use_mfp;
};
/**
* struct cfg80211_deauth_request - Deauthentication request data
*
* This structure provides information needed to complete IEEE 802.11
* deauthentication.
*
* @bss: the BSS to deauthenticate from
* @ie: Extra IEs to add to Deauthentication frame or %NULL
* @ie_len: Length of ie buffer in octets
* @reason_code: The reason code for the deauthentication
*/
struct cfg80211_deauth_request {
struct cfg80211_bss *bss;
const u8 *ie;
size_t ie_len;
u16 reason_code;
};
/**
* struct cfg80211_disassoc_request - Disassociation request data
*
* This structure provides information needed to complete IEEE 802.11
* disassocation.
*
* @bss: the BSS to disassociate from
* @ie: Extra IEs to add to Disassociation frame or %NULL
* @ie_len: Length of ie buffer in octets
* @reason_code: The reason code for the disassociation
*/
struct cfg80211_disassoc_request {
struct cfg80211_bss *bss;
const u8 *ie;
size_t ie_len;
u16 reason_code;
};
/**
* struct cfg80211_ibss_params - IBSS parameters
*
* This structure defines the IBSS parameters for the join_ibss()
* method.
*
* @ssid: The SSID, will always be non-null.
* @ssid_len: The length of the SSID, will always be non-zero.
* @bssid: Fixed BSSID requested, maybe be %NULL, if set do not
* search for IBSSs with a different BSSID.
* @channel: The channel to use if no IBSS can be found to join.
* @channel_fixed: The channel should be fixed -- do not search for
* IBSSs to join on other channels.
* @ie: information element(s) to include in the beacon
* @ie_len: length of that
* @beacon_interval: beacon interval to use
*/
struct cfg80211_ibss_params {
u8 *ssid;
u8 *bssid;
struct ieee80211_channel *channel;
u8 *ie;
u8 ssid_len, ie_len;
u16 beacon_interval;
bool channel_fixed;
};
/**
* struct cfg80211_connect_params - Connection parameters
*
* This structure provides information needed to complete IEEE 802.11
* authentication and association.
*
* @channel: The channel to use or %NULL if not specified (auto-select based
* on scan results)
* @bssid: The AP BSSID or %NULL if not specified (auto-select based on scan
* results)
* @ssid: SSID
* @ssid_len: Length of ssid in octets
* @auth_type: Authentication type (algorithm)
* @assoc_ie: IEs for association request
* @assoc_ie_len: Length of assoc_ie in octets
* @privacy: indicates whether privacy-enabled APs should be used
* @crypto: crypto settings
*/
struct cfg80211_connect_params {
struct ieee80211_channel *channel;
u8 *bssid;
u8 *ssid;
size_t ssid_len;
enum nl80211_auth_type auth_type;
u8 *ie;
size_t ie_len;
bool privacy;
struct cfg80211_crypto_settings crypto;
};
/**
* enum wiphy_params_flags - set_wiphy_params bitfield values
* WIPHY_PARAM_RETRY_SHORT: wiphy->retry_short has changed
* WIPHY_PARAM_RETRY_LONG: wiphy->retry_long has changed
* WIPHY_PARAM_FRAG_THRESHOLD: wiphy->frag_threshold has changed
* WIPHY_PARAM_RTS_THRESHOLD: wiphy->rts_threshold has changed
*/
enum wiphy_params_flags {
WIPHY_PARAM_RETRY_SHORT = 1 << 0,
WIPHY_PARAM_RETRY_LONG = 1 << 1,
WIPHY_PARAM_FRAG_THRESHOLD = 1 << 2,
WIPHY_PARAM_RTS_THRESHOLD = 1 << 3,
};
/**
* enum tx_power_setting - TX power adjustment
*
* @TX_POWER_AUTOMATIC: the dbm parameter is ignored
* @TX_POWER_LIMITED: limit TX power by the dbm parameter
* @TX_POWER_FIXED: fix TX power to the dbm parameter
*/
enum tx_power_setting {
TX_POWER_AUTOMATIC,
TX_POWER_LIMITED,
TX_POWER_FIXED,
};
/*
* cfg80211_bitrate_mask - masks for bitrate control
*/
struct cfg80211_bitrate_mask {
/*
* As discussed in Berlin, this struct really
* should look like this:
struct {
u32 legacy;
u8 mcs[IEEE80211_HT_MCS_MASK_LEN];
} control[IEEE80211_NUM_BANDS];
* Since we can always fix in-kernel users, let's keep
* it simpler for now:
*/
u32 fixed; /* fixed bitrate, 0 == not fixed */
u32 maxrate; /* in kbps, 0 == no limit */
};
/**
* struct cfg80211_ops - backend description for wireless configuration
*
* This struct is registered by fullmac card drivers and/or wireless stacks
* in order to handle configuration requests on their interfaces.
*
* All callbacks except where otherwise noted should return 0
* on success or a negative error code.
*
* All operations are currently invoked under rtnl for consistency with the
* wireless extensions but this is subject to reevaluation as soon as this
* code is used more widely and we have a first user without wext.
*
* @suspend: wiphy device needs to be suspended
* @resume: wiphy device needs to be resumed
*
* @add_virtual_intf: create a new virtual interface with the given name,
* must set the struct wireless_dev's iftype.
*
* @del_virtual_intf: remove the virtual interface determined by ifindex.
*
* @change_virtual_intf: change type/configuration of virtual interface,
* keep the struct wireless_dev's iftype updated.
*
* @add_key: add a key with the given parameters. @mac_addr will be %NULL
* when adding a group key.
*
* @get_key: get information about the key with the given parameters.
* @mac_addr will be %NULL when requesting information for a group
* key. All pointers given to the @callback function need not be valid
* after it returns. This function should return an error if it is
* not possible to retrieve the key, -ENOENT if it doesn't exist.
*
* @del_key: remove a key given the @mac_addr (%NULL for a group key)
* and @key_index, return -ENOENT if the key doesn't exist.
*
* @set_default_key: set the default key on an interface
*
* @set_default_mgmt_key: set the default management frame key on an interface
*
* @add_beacon: Add a beacon with given parameters, @head, @interval
* and @dtim_period will be valid, @tail is optional.
* @set_beacon: Change the beacon parameters for an access point mode
* interface. This should reject the call when no beacon has been
* configured.
* @del_beacon: Remove beacon configuration and stop sending the beacon.
*
* @add_station: Add a new station.
*
* @del_station: Remove a station; @mac may be NULL to remove all stations.
*
* @change_station: Modify a given station.
*
* @get_mesh_params: Put the current mesh parameters into *params
*
* @set_mesh_params: Set mesh parameters.
* The mask is a bitfield which tells us which parameters to
* set, and which to leave alone.
*
* @set_mesh_cfg: set mesh parameters (by now, just mesh id)
*
* @change_bss: Modify parameters for a given BSS.
*
* @set_txq_params: Set TX queue parameters
*
* @set_channel: Set channel
*
* @scan: Request to do a scan. If returning zero, the scan request is given
* the driver, and will be valid until passed to cfg80211_scan_done().
* For scan results, call cfg80211_inform_bss(); you can call this outside
* the scan/scan_done bracket too.
*
* @auth: Request to authenticate with the specified peer
* @assoc: Request to (re)associate with the specified peer
* @deauth: Request to deauthenticate from the specified peer
* @disassoc: Request to disassociate from the specified peer
*
* @connect: Connect to the ESS with the specified parameters. When connected,
* call cfg80211_connect_result() with status code %WLAN_STATUS_SUCCESS.
* If the connection fails for some reason, call cfg80211_connect_result()
* with the status from the AP.
* @disconnect: Disconnect from the BSS/ESS.
*
* @join_ibss: Join the specified IBSS (or create if necessary). Once done, call
* cfg80211_ibss_joined(), also call that function when changing BSSID due
* to a merge.
* @leave_ibss: Leave the IBSS.
*
* @set_wiphy_params: Notify that wiphy parameters have changed;
* @changed bitfield (see &enum wiphy_params_flags) describes which values
* have changed. The actual parameter values are available in
* struct wiphy. If returning an error, no value should be changed.
*
* @set_tx_power: set the transmit power according to the parameters
* @get_tx_power: store the current TX power into the dbm variable;
* return 0 if successful
*
* @rfkill_poll: polls the hw rfkill line, use cfg80211 reporting
* functions to adjust rfkill hw state
*
* @testmode_cmd: run a test mode command
*/
struct cfg80211_ops {
int (*suspend)(struct wiphy *wiphy);
int (*resume)(struct wiphy *wiphy);
int (*add_virtual_intf)(struct wiphy *wiphy, char *name,
enum nl80211_iftype type, u32 *flags,
struct vif_params *params);
int (*del_virtual_intf)(struct wiphy *wiphy, int ifindex);
int (*change_virtual_intf)(struct wiphy *wiphy,
struct net_device *dev,
enum nl80211_iftype type, u32 *flags,
struct vif_params *params);
int (*add_key)(struct wiphy *wiphy, struct net_device *netdev,
u8 key_index, const u8 *mac_addr,
struct key_params *params);
int (*get_key)(struct wiphy *wiphy, struct net_device *netdev,
u8 key_index, const u8 *mac_addr, void *cookie,
void (*callback)(void *cookie, struct key_params*));
int (*del_key)(struct wiphy *wiphy, struct net_device *netdev,
u8 key_index, const u8 *mac_addr);
int (*set_default_key)(struct wiphy *wiphy,
struct net_device *netdev,
u8 key_index);
int (*set_default_mgmt_key)(struct wiphy *wiphy,
struct net_device *netdev,
u8 key_index);
int (*add_beacon)(struct wiphy *wiphy, struct net_device *dev,
struct beacon_parameters *info);
int (*set_beacon)(struct wiphy *wiphy, struct net_device *dev,
struct beacon_parameters *info);
int (*del_beacon)(struct wiphy *wiphy, struct net_device *dev);
int (*add_station)(struct wiphy *wiphy, struct net_device *dev,
u8 *mac, struct station_parameters *params);
int (*del_station)(struct wiphy *wiphy, struct net_device *dev,
u8 *mac);
int (*change_station)(struct wiphy *wiphy, struct net_device *dev,
u8 *mac, struct station_parameters *params);
int (*get_station)(struct wiphy *wiphy, struct net_device *dev,
u8 *mac, struct station_info *sinfo);
int (*dump_station)(struct wiphy *wiphy, struct net_device *dev,
int idx, u8 *mac, struct station_info *sinfo);
int (*add_mpath)(struct wiphy *wiphy, struct net_device *dev,
u8 *dst, u8 *next_hop);
int (*del_mpath)(struct wiphy *wiphy, struct net_device *dev,
u8 *dst);
int (*change_mpath)(struct wiphy *wiphy, struct net_device *dev,
u8 *dst, u8 *next_hop);
int (*get_mpath)(struct wiphy *wiphy, struct net_device *dev,
u8 *dst, u8 *next_hop,
struct mpath_info *pinfo);
int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
int idx, u8 *dst, u8 *next_hop,
struct mpath_info *pinfo);
int (*get_mesh_params)(struct wiphy *wiphy,
struct net_device *dev,
struct mesh_config *conf);
int (*set_mesh_params)(struct wiphy *wiphy,
struct net_device *dev,
const struct mesh_config *nconf, u32 mask);
int (*change_bss)(struct wiphy *wiphy, struct net_device *dev,
struct bss_parameters *params);
int (*set_txq_params)(struct wiphy *wiphy,
struct ieee80211_txq_params *params);
int (*set_channel)(struct wiphy *wiphy,
struct ieee80211_channel *chan,
enum nl80211_channel_type channel_type);
int (*scan)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_scan_request *request);
int (*auth)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_auth_request *req);
int (*assoc)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_assoc_request *req);
int (*deauth)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_deauth_request *req,
void *cookie);
int (*disassoc)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_disassoc_request *req,
void *cookie);
int (*connect)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_connect_params *sme);
int (*disconnect)(struct wiphy *wiphy, struct net_device *dev,
u16 reason_code);
int (*join_ibss)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_ibss_params *params);
int (*leave_ibss)(struct wiphy *wiphy, struct net_device *dev);
int (*set_wiphy_params)(struct wiphy *wiphy, u32 changed);
int (*set_tx_power)(struct wiphy *wiphy,
enum tx_power_setting type, int dbm);
int (*get_tx_power)(struct wiphy *wiphy, int *dbm);
int (*set_wds_peer)(struct wiphy *wiphy, struct net_device *dev,
u8 *addr);
void (*rfkill_poll)(struct wiphy *wiphy);
#ifdef CONFIG_NL80211_TESTMODE
int (*testmode_cmd)(struct wiphy *wiphy, void *data, int len);
#endif
int (*set_bitrate_mask)(struct wiphy *wiphy,
struct net_device *dev,
const u8 *peer,
const struct cfg80211_bitrate_mask *mask);
/* some temporary stuff to finish wext */
int (*set_power_mgmt)(struct wiphy *wiphy, struct net_device *dev,
bool enabled, int timeout);
};
/*
* wireless hardware and networking interfaces structures
* and registration/helper functions
*/
/**
* struct wiphy - wireless hardware description
* @idx: the wiphy index assigned to this item
* @class_dev: the class device representing /sys/class/ieee80211/<wiphy-name>
* @custom_regulatory: tells us the driver for this device
* has its own custom regulatory domain and cannot identify the
* ISO / IEC 3166 alpha2 it belongs to. When this is enabled
* we will disregard the first regulatory hint (when the
* initiator is %REGDOM_SET_BY_CORE).
* @strict_regulatory: tells us the driver for this device will ignore
* regulatory domain settings until it gets its own regulatory domain
* via its regulatory_hint(). After its gets its own regulatory domain
* it will only allow further regulatory domain settings to further
* enhance compliance. For example if channel 13 and 14 are disabled
* by this regulatory domain no user regulatory domain can enable these
* channels at a later time. This can be used for devices which do not
* have calibration information gauranteed for frequencies or settings
* outside of its regulatory domain.
* @reg_notifier: the driver's regulatory notification callback
* @regd: the driver's regulatory domain, if one was requested via
* the regulatory_hint() API. This can be used by the driver
* on the reg_notifier() if it chooses to ignore future
* regulatory domain changes caused by other drivers.
* @signal_type: signal type reported in &struct cfg80211_bss.
* @cipher_suites: supported cipher suites
* @n_cipher_suites: number of supported cipher suites
* @retry_short: Retry limit for short frames (dot11ShortRetryLimit)
* @retry_long: Retry limit for long frames (dot11LongRetryLimit)
* @frag_threshold: Fragmentation threshold (dot11FragmentationThreshold);
* -1 = fragmentation disabled, only odd values >= 256 used
* @rts_threshold: RTS threshold (dot11RTSThreshold); -1 = RTS/CTS disabled
*/
struct wiphy {
/* assign these fields before you register the wiphy */
/* permanent MAC address */
u8 perm_addr[ETH_ALEN];
/* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */
u16 interface_modes;
bool custom_regulatory;
bool strict_regulatory;
enum cfg80211_signal_type signal_type;
int bss_priv_size;
u8 max_scan_ssids;
u16 max_scan_ie_len;
int n_cipher_suites;
const u32 *cipher_suites;
u8 retry_short;
u8 retry_long;
u32 frag_threshold;
u32 rts_threshold;
/* If multiple wiphys are registered and you're handed e.g.
* a regular netdev with assigned ieee80211_ptr, you won't
* know whether it points to a wiphy your driver has registered
* or not. Assign this to something global to your driver to
* help determine whether you own this wiphy or not. */
const void *privid;
struct ieee80211_supported_band *bands[IEEE80211_NUM_BANDS];
/* Lets us get back the wiphy on the callback */
int (*reg_notifier)(struct wiphy *wiphy,
struct regulatory_request *request);
/* fields below are read-only, assigned by cfg80211 */
const struct ieee80211_regdomain *regd;
/* the item in /sys/class/ieee80211/ points to this,
* you need use set_wiphy_dev() (see below) */
struct device dev;
/* dir in debugfs: ieee80211/<wiphyname> */
struct dentry *debugfsdir;
char priv[0] __attribute__((__aligned__(NETDEV_ALIGN)));
};
/**
* wiphy_priv - return priv from wiphy
*
* @wiphy: the wiphy whose priv pointer to return
*/
static inline void *wiphy_priv(struct wiphy *wiphy)
{
BUG_ON(!wiphy);
return &wiphy->priv;
}
/**
* priv_to_wiphy - return the wiphy containing the priv
*
* @priv: a pointer previously returned by wiphy_priv
*/
static inline struct wiphy *priv_to_wiphy(void *priv)
{
BUG_ON(!priv);
return container_of(priv, struct wiphy, priv);
}
/**
* set_wiphy_dev - set device pointer for wiphy
*
* @wiphy: The wiphy whose device to bind
* @dev: The device to parent it to
*/
static inline void set_wiphy_dev(struct wiphy *wiphy, struct device *dev)
{
wiphy->dev.parent = dev;
}
/**
* wiphy_dev - get wiphy dev pointer
*
* @wiphy: The wiphy whose device struct to look up
*/
static inline struct device *wiphy_dev(struct wiphy *wiphy)
{
return wiphy->dev.parent;
}
/**
* wiphy_name - get wiphy name
*
* @wiphy: The wiphy whose name to return
*/
static inline const char *wiphy_name(struct wiphy *wiphy)
{
return dev_name(&wiphy->dev);
}
/**
* wiphy_new - create a new wiphy for use with cfg80211
*
* @ops: The configuration operations for this device
* @sizeof_priv: The size of the private area to allocate
*
* Create a new wiphy and associate the given operations with it.
* @sizeof_priv bytes are allocated for private use.
*
* The returned pointer must be assigned to each netdev's
* ieee80211_ptr for proper operation.
*/
struct wiphy *wiphy_new(const struct cfg80211_ops *ops, int sizeof_priv);
/**
* wiphy_register - register a wiphy with cfg80211
*
* @wiphy: The wiphy to register.
*
* Returns a non-negative wiphy index or a negative error code.
*/
extern int wiphy_register(struct wiphy *wiphy);
/**
* wiphy_unregister - deregister a wiphy from cfg80211
*
* @wiphy: The wiphy to unregister.
*
* After this call, no more requests can be made with this priv
* pointer, but the call may sleep to wait for an outstanding
* request that is being handled.
*/
extern void wiphy_unregister(struct wiphy *wiphy);
/**
* wiphy_free - free wiphy
*
* @wiphy: The wiphy to free
*/
extern void wiphy_free(struct wiphy *wiphy);
/* internal struct */
struct cfg80211_conn;
struct cfg80211_internal_bss;
#define MAX_AUTH_BSSES 4
/**
* struct wireless_dev - wireless per-netdev state
*
* This structure must be allocated by the driver/stack
* that uses the ieee80211_ptr field in struct net_device
* (this is intentional so it can be allocated along with
* the netdev.)
*
* @wiphy: pointer to hardware description
* @iftype: interface type
* @list: (private) Used to collect the interfaces
* @netdev: (private) Used to reference back to the netdev
* @current_bss: (private) Used by the internal configuration code
* @bssid: (private) Used by the internal configuration code
* @ssid: (private) Used by the internal configuration code
* @ssid_len: (private) Used by the internal configuration code
* @wext: (private) Used by the internal wireless extensions compat code
* @wext_bssid: (private) Used by the internal wireless extensions compat code
*/
struct wireless_dev {
struct wiphy *wiphy;
enum nl80211_iftype iftype;
/* the remainder of this struct should be private to cfg80211 */
struct list_head list;
struct net_device *netdev;
struct mutex mtx;
/* currently used for IBSS and SME - might be rearranged later */
u8 ssid[IEEE80211_MAX_SSID_LEN];
u8 ssid_len;
enum {
CFG80211_SME_IDLE,
CFG80211_SME_CONNECTING,
CFG80211_SME_CONNECTED,
} sme_state;
struct cfg80211_conn *conn;
struct list_head event_list;
spinlock_t event_lock;
struct cfg80211_internal_bss *authtry_bsses[MAX_AUTH_BSSES];
struct cfg80211_internal_bss *auth_bsses[MAX_AUTH_BSSES];
struct cfg80211_internal_bss *current_bss; /* associated / joined */
#ifdef CONFIG_WIRELESS_EXT
/* wext data */
struct {
struct cfg80211_ibss_params ibss;
struct cfg80211_connect_params connect;
u8 *ie;
size_t ie_len;
u8 bssid[ETH_ALEN];
u8 ssid[IEEE80211_MAX_SSID_LEN];
s8 default_key, default_mgmt_key;
bool ps;
int ps_timeout;
} wext;
#endif
};
/**
* wdev_priv - return wiphy priv from wireless_dev
*
* @wdev: The wireless device whose wiphy's priv pointer to return
*/
static inline void *wdev_priv(struct wireless_dev *wdev)
{
BUG_ON(!wdev);
return wiphy_priv(wdev->wiphy);
}
/*
* Utility functions
*/
/**
* ieee80211_channel_to_frequency - convert channel number to frequency
*/
extern int ieee80211_channel_to_frequency(int chan);
/**
* ieee80211_frequency_to_channel - convert frequency to channel number
*/
extern int ieee80211_frequency_to_channel(int freq);
/*
* Name indirection necessary because the ieee80211 code also has
* a function named "ieee80211_get_channel", so if you include
* cfg80211's header file you get cfg80211's version, if you try
* to include both header files you'll (rightfully!) get a symbol
* clash.
*/
extern struct ieee80211_channel *__ieee80211_get_channel(struct wiphy *wiphy,
int freq);
/**
* ieee80211_get_channel - get channel struct from wiphy for specified frequency
*/
static inline struct ieee80211_channel *
ieee80211_get_channel(struct wiphy *wiphy, int freq)
{
return __ieee80211_get_channel(wiphy, freq);
}
/**
* ieee80211_get_response_rate - get basic rate for a given rate
*
* @sband: the band to look for rates in
* @basic_rates: bitmap of basic rates
* @bitrate: the bitrate for which to find the basic rate
*
* This function returns the basic rate corresponding to a given
* bitrate, that is the next lower bitrate contained in the basic
* rate map, which is, for this function, given as a bitmap of
* indices of rates in the band's bitrate table.
*/
struct ieee80211_rate *
ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
u32 basic_rates, int bitrate);
/*
* Radiotap parsing functions -- for controlled injection support
*
* Implemented in net/wireless/radiotap.c
* Documentation in Documentation/networking/radiotap-headers.txt
*/
/**
* struct ieee80211_radiotap_iterator - tracks walk thru present radiotap args
* @rtheader: pointer to the radiotap header we are walking through
* @max_length: length of radiotap header in cpu byte ordering
* @this_arg_index: IEEE80211_RADIOTAP_... index of current arg
* @this_arg: pointer to current radiotap arg
* @arg_index: internal next argument index
* @arg: internal next argument pointer
* @next_bitmap: internal pointer to next present u32
* @bitmap_shifter: internal shifter for curr u32 bitmap, b0 set == arg present
*/
struct ieee80211_radiotap_iterator {
struct ieee80211_radiotap_header *rtheader;
int max_length;
int this_arg_index;
u8 *this_arg;
int arg_index;
u8 *arg;
__le32 *next_bitmap;
u32 bitmap_shifter;
};
extern int ieee80211_radiotap_iterator_init(
struct ieee80211_radiotap_iterator *iterator,
struct ieee80211_radiotap_header *radiotap_header,
int max_length);
extern int ieee80211_radiotap_iterator_next(
struct ieee80211_radiotap_iterator *iterator);
extern const unsigned char rfc1042_header[6];
extern const unsigned char bridge_tunnel_header[6];
/**
* ieee80211_get_hdrlen_from_skb - get header length from data
*
* Given an skb with a raw 802.11 header at the data pointer this function
* returns the 802.11 header length in bytes (not including encryption
* headers). If the data in the sk_buff is too short to contain a valid 802.11
* header the function returns 0.
*
* @skb: the frame
*/
unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
/**
* ieee80211_hdrlen - get header length in bytes from frame control
* @fc: frame control field in little-endian format
*/
unsigned int ieee80211_hdrlen(__le16 fc);
/**
* ieee80211_data_to_8023 - convert an 802.11 data frame to 802.3
* @skb: the 802.11 data frame
* @addr: the device MAC address
* @iftype: the virtual interface type
*/
int ieee80211_data_to_8023(struct sk_buff *skb, u8 *addr,
enum nl80211_iftype iftype);
/**
* ieee80211_data_from_8023 - convert an 802.3 frame to 802.11
* @skb: the 802.3 frame
* @addr: the device MAC address
* @iftype: the virtual interface type
* @bssid: the network bssid (used only for iftype STATION and ADHOC)
* @qos: build 802.11 QoS data frame
*/
int ieee80211_data_from_8023(struct sk_buff *skb, u8 *addr,
enum nl80211_iftype iftype, u8 *bssid, bool qos);
/**
* cfg80211_classify8021d - determine the 802.1p/1d tag for a data frame
* @skb: the data frame
*/
unsigned int cfg80211_classify8021d(struct sk_buff *skb);
/*
* Regulatory helper functions for wiphys
*/
/**
* regulatory_hint - driver hint to the wireless core a regulatory domain
* @wiphy: the wireless device giving the hint (used only for reporting
* conflicts)
* @alpha2: the ISO/IEC 3166 alpha2 the driver claims its regulatory domain
* should be in. If @rd is set this should be NULL. Note that if you
* set this to NULL you should still set rd->alpha2 to some accepted
* alpha2.
*
* Wireless drivers can use this function to hint to the wireless core
* what it believes should be the current regulatory domain by
* giving it an ISO/IEC 3166 alpha2 country code it knows its regulatory
* domain should be in or by providing a completely build regulatory domain.
* If the driver provides an ISO/IEC 3166 alpha2 userspace will be queried
* for a regulatory domain structure for the respective country.
*
* The wiphy must have been registered to cfg80211 prior to this call.
* For cfg80211 drivers this means you must first use wiphy_register(),
* for mac80211 drivers you must first use ieee80211_register_hw().
*
* Drivers should check the return value, its possible you can get
* an -ENOMEM.
*/
extern int regulatory_hint(struct wiphy *wiphy, const char *alpha2);
/**
* regulatory_hint_11d - hints a country IE as a regulatory domain
* @wiphy: the wireless device giving the hint (used only for reporting
* conflicts)
* @country_ie: pointer to the country IE
* @country_ie_len: length of the country IE
*
* We will intersect the rd with the what CRDA tells us should apply
* for the alpha2 this country IE belongs to, this prevents APs from
* sending us incorrect or outdated information against a country.
*/
extern void regulatory_hint_11d(struct wiphy *wiphy,
u8 *country_ie,
u8 country_ie_len);
/**
* wiphy_apply_custom_regulatory - apply a custom driver regulatory domain
* @wiphy: the wireless device we want to process the regulatory domain on
* @regd: the custom regulatory domain to use for this wiphy
*
* Drivers can sometimes have custom regulatory domains which do not apply
* to a specific country. Drivers can use this to apply such custom regulatory
* domains. This routine must be called prior to wiphy registration. The
* custom regulatory domain will be trusted completely and as such previous
* default channel settings will be disregarded. If no rule is found for a
* channel on the regulatory domain the channel will be disabled.
*/
extern void wiphy_apply_custom_regulatory(
struct wiphy *wiphy,
const struct ieee80211_regdomain *regd);
/**
* freq_reg_info - get regulatory information for the given frequency
* @wiphy: the wiphy for which we want to process this rule for
* @center_freq: Frequency in KHz for which we want regulatory information for
* @desired_bw_khz: the desired max bandwidth you want to use per
* channel. Note that this is still 20 MHz if you want to use HT40
* as HT40 makes use of two channels for its 40 MHz width bandwidth.
* If set to 0 we'll assume you want the standard 20 MHz.
* @reg_rule: the regulatory rule which we have for this frequency
*
* Use this function to get the regulatory rule for a specific frequency on
* a given wireless device. If the device has a specific regulatory domain
* it wants to follow we respect that unless a country IE has been received
* and processed already.
*
* Returns 0 if it was able to find a valid regulatory rule which does
* apply to the given center_freq otherwise it returns non-zero. It will
* also return -ERANGE if we determine the given center_freq does not even have
* a regulatory rule for a frequency range in the center_freq's band. See
* freq_in_rule_band() for our current definition of a band -- this is purely
* subjective and right now its 802.11 specific.
*/
extern int freq_reg_info(struct wiphy *wiphy,
u32 center_freq,
u32 desired_bw_khz,
const struct ieee80211_reg_rule **reg_rule);
/*
* Temporary wext handlers & helper functions
*
* In the future cfg80211 will simply assign the entire wext handler
* structure to netdevs it manages, but we're not there yet.
*/
int cfg80211_wext_giwname(struct net_device *dev,
struct iw_request_info *info,
char *name, char *extra);
int cfg80211_wext_siwmode(struct net_device *dev, struct iw_request_info *info,
u32 *mode, char *extra);
int cfg80211_wext_giwmode(struct net_device *dev, struct iw_request_info *info,
u32 *mode, char *extra);
int cfg80211_wext_siwscan(struct net_device *dev,
struct iw_request_info *info,
union iwreq_data *wrqu, char *extra);
int cfg80211_wext_giwscan(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *extra);
int cfg80211_wext_siwmlme(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *extra);
int cfg80211_wext_giwrange(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *extra);
int cfg80211_ibss_wext_siwfreq(struct net_device *dev,
struct iw_request_info *info,
struct iw_freq *freq, char *extra);
int cfg80211_ibss_wext_giwfreq(struct net_device *dev,
struct iw_request_info *info,
struct iw_freq *freq, char *extra);
int cfg80211_ibss_wext_siwessid(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *ssid);
int cfg80211_ibss_wext_giwessid(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *ssid);
int cfg80211_ibss_wext_siwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *ap_addr, char *extra);
int cfg80211_ibss_wext_giwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *ap_addr, char *extra);
int cfg80211_mgd_wext_siwfreq(struct net_device *dev,
struct iw_request_info *info,
struct iw_freq *freq, char *extra);
int cfg80211_mgd_wext_giwfreq(struct net_device *dev,
struct iw_request_info *info,
struct iw_freq *freq, char *extra);
int cfg80211_mgd_wext_siwessid(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *ssid);
int cfg80211_mgd_wext_giwessid(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *ssid);
int cfg80211_mgd_wext_siwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *ap_addr, char *extra);
int cfg80211_mgd_wext_giwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *ap_addr, char *extra);
int cfg80211_wext_siwgenie(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *data, char *extra);
int cfg80211_wext_siwauth(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *data, char *extra);
int cfg80211_wext_giwauth(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *data, char *extra);
struct ieee80211_channel *cfg80211_wext_freq(struct wiphy *wiphy,
struct iw_freq *freq);
int cfg80211_wext_siwrate(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *rate, char *extra);
int cfg80211_wext_giwrate(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *rate, char *extra);
int cfg80211_wext_siwrts(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *rts, char *extra);
int cfg80211_wext_giwrts(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *rts, char *extra);
int cfg80211_wext_siwfrag(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *frag, char *extra);
int cfg80211_wext_giwfrag(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *frag, char *extra);
int cfg80211_wext_siwretry(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *retry, char *extra);
int cfg80211_wext_giwretry(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *retry, char *extra);
int cfg80211_wext_siwencodeext(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *erq, char *extra);
int cfg80211_wext_siwencode(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *erq, char *keybuf);
int cfg80211_wext_giwencode(struct net_device *dev,
struct iw_request_info *info,
struct iw_point *erq, char *keybuf);
int cfg80211_wext_siwtxpower(struct net_device *dev,
struct iw_request_info *info,
union iwreq_data *data, char *keybuf);
int cfg80211_wext_giwtxpower(struct net_device *dev,
struct iw_request_info *info,
union iwreq_data *data, char *keybuf);
struct iw_statistics *cfg80211_wireless_stats(struct net_device *dev);
int cfg80211_wext_siwpower(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *wrq, char *extra);
int cfg80211_wext_giwpower(struct net_device *dev,
struct iw_request_info *info,
struct iw_param *wrq, char *extra);
int cfg80211_wds_wext_siwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *addr, char *extra);
int cfg80211_wds_wext_giwap(struct net_device *dev,
struct iw_request_info *info,
struct sockaddr *addr, char *extra);
/*
* callbacks for asynchronous cfg80211 methods, notification
* functions and BSS handling helpers
*/
/**
* cfg80211_scan_done - notify that scan finished
*
* @request: the corresponding scan request
* @aborted: set to true if the scan was aborted for any reason,
* userspace will be notified of that
*/
void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted);
/**
* cfg80211_inform_bss - inform cfg80211 of a new BSS
*
* @wiphy: the wiphy reporting the BSS
* @bss: the found BSS
* @signal: the signal strength, type depends on the wiphy's signal_type
* @gfp: context flags
*
* This informs cfg80211 that BSS information was found and
* the BSS should be updated/added.
*/
struct cfg80211_bss*
cfg80211_inform_bss_frame(struct wiphy *wiphy,
struct ieee80211_channel *channel,
struct ieee80211_mgmt *mgmt, size_t len,
s32 signal, gfp_t gfp);
struct cfg80211_bss*
cfg80211_inform_bss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *bssid,
u64 timestamp, u16 capability, u16 beacon_interval,
const u8 *ie, size_t ielen,
s32 signal, gfp_t gfp);
struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *bssid,
const u8 *ssid, size_t ssid_len,
u16 capa_mask, u16 capa_val);
static inline struct cfg80211_bss *
cfg80211_get_ibss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *ssid, size_t ssid_len)
{
return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len,
WLAN_CAPABILITY_IBSS, WLAN_CAPABILITY_IBSS);
}
struct cfg80211_bss *cfg80211_get_mesh(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *meshid, size_t meshidlen,
const u8 *meshcfg);
void cfg80211_put_bss(struct cfg80211_bss *bss);
/**
* cfg80211_unlink_bss - unlink BSS from internal data structures
* @wiphy: the wiphy
* @bss: the bss to remove
*
* This function removes the given BSS from the internal data structures
* thereby making it no longer show up in scan results etc. Use this
* function when you detect a BSS is gone. Normally BSSes will also time
* out, so it is not necessary to use this function at all.
*/
void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
/**
* cfg80211_send_rx_auth - notification of processed authentication
* @dev: network device
* @buf: authentication frame (header + body)
* @len: length of the frame data
*
* This function is called whenever an authentication has been processed in
* station mode. The driver is required to call either this function or
* cfg80211_send_auth_timeout() to indicate the result of cfg80211_ops::auth()
* call. This function may sleep.
*/
void cfg80211_send_rx_auth(struct net_device *dev, const u8 *buf, size_t len);
/**
* cfg80211_send_auth_timeout - notification of timed out authentication
* @dev: network device
* @addr: The MAC address of the device with which the authentication timed out
*
* This function may sleep.
*/
void cfg80211_send_auth_timeout(struct net_device *dev, const u8 *addr);
/**
* cfg80211_send_rx_assoc - notification of processed association
* @dev: network device
* @buf: (re)association response frame (header + body)
* @len: length of the frame data
*
* This function is called whenever a (re)association response has been
* processed in station mode. The driver is required to call either this
* function or cfg80211_send_assoc_timeout() to indicate the result of
* cfg80211_ops::assoc() call. This function may sleep.
*/
void cfg80211_send_rx_assoc(struct net_device *dev, const u8 *buf, size_t len);
/**
* cfg80211_send_assoc_timeout - notification of timed out association
* @dev: network device
* @addr: The MAC address of the device with which the association timed out
*
* This function may sleep.
*/
void cfg80211_send_assoc_timeout(struct net_device *dev, const u8 *addr);
/**
* cfg80211_send_deauth - notification of processed deauthentication
* @dev: network device
* @buf: deauthentication frame (header + body)
* @len: length of the frame data
* @cookie: cookie from ->deauth if called within that callback,
* %NULL otherwise
*
* This function is called whenever deauthentication has been processed in
* station mode. This includes both received deauthentication frames and
* locally generated ones. This function may sleep.
*/
void cfg80211_send_deauth(struct net_device *dev, const u8 *buf, size_t len,
void *cookie);
/**
* cfg80211_send_disassoc - notification of processed disassociation
* @dev: network device
* @buf: disassociation response frame (header + body)
* @len: length of the frame data
* @cookie: cookie from ->disassoc if called within that callback,
* %NULL otherwise
*
* This function is called whenever disassociation has been processed in
* station mode. This includes both received disassociation frames and locally
* generated ones. This function may sleep.
*/
void cfg80211_send_disassoc(struct net_device *dev, const u8 *buf, size_t len,
void *cookie);
/**
* cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP)
* @dev: network device
* @addr: The source MAC address of the frame
* @key_type: The key type that the received frame used
* @key_id: Key identifier (0..3)
* @tsc: The TSC value of the frame that generated the MIC failure (6 octets)
* @gfp: allocation flags
*
* This function is called whenever the local MAC detects a MIC failure in a
* received frame. This matches with MLME-MICHAELMICFAILURE.indication()
* primitive.
*/
void cfg80211_michael_mic_failure(struct net_device *dev, const u8 *addr,
enum nl80211_key_type key_type, int key_id,
const u8 *tsc, gfp_t gfp);
/**
* cfg80211_ibss_joined - notify cfg80211 that device joined an IBSS
*
* @dev: network device
* @bssid: the BSSID of the IBSS joined
* @gfp: allocation flags
*
* This function notifies cfg80211 that the device joined an IBSS or
* switched to a different BSSID. Before this function can be called,
* either a beacon has to have been received from the IBSS, or one of
* the cfg80211_inform_bss{,_frame} functions must have been called
* with the locally generated beacon -- this guarantees that there is
* always a scan result for this IBSS. cfg80211 will handle the rest.
*/
void cfg80211_ibss_joined(struct net_device *dev, const u8 *bssid, gfp_t gfp);
/**
* wiphy_rfkill_set_hw_state - notify cfg80211 about hw block state
* @wiphy: the wiphy
* @blocked: block status
*/
void wiphy_rfkill_set_hw_state(struct wiphy *wiphy, bool blocked);
/**
* wiphy_rfkill_start_polling - start polling rfkill
* @wiphy: the wiphy
*/
void wiphy_rfkill_start_polling(struct wiphy *wiphy);
/**
* wiphy_rfkill_stop_polling - stop polling rfkill
* @wiphy: the wiphy
*/
void wiphy_rfkill_stop_polling(struct wiphy *wiphy);
#ifdef CONFIG_NL80211_TESTMODE
/**
* cfg80211_testmode_alloc_reply_skb - allocate testmode reply
* @wiphy: the wiphy
* @approxlen: an upper bound of the length of the data that will
* be put into the skb
*
* This function allocates and pre-fills an skb for a reply to
* the testmode command. Since it is intended for a reply, calling
* it outside of the @testmode_cmd operation is invalid.
*
* The returned skb (or %NULL if any errors happen) is pre-filled
* with the wiphy index and set up in a way that any data that is
* put into the skb (with skb_put(), nla_put() or similar) will end
* up being within the %NL80211_ATTR_TESTDATA attribute, so all that
* needs to be done with the skb is adding data for the corresponding
* userspace tool which can then read that data out of the testdata
* attribute. You must not modify the skb in any other way.
*
* When done, call cfg80211_testmode_reply() with the skb and return
* its error code as the result of the @testmode_cmd operation.
*/
struct sk_buff *cfg80211_testmode_alloc_reply_skb(struct wiphy *wiphy,
int approxlen);
/**
* cfg80211_testmode_reply - send the reply skb
* @skb: The skb, must have been allocated with
* cfg80211_testmode_alloc_reply_skb()
*
* Returns an error code or 0 on success, since calling this
* function will usually be the last thing before returning
* from the @testmode_cmd you should return the error code.
* Note that this function consumes the skb regardless of the
* return value.
*/
int cfg80211_testmode_reply(struct sk_buff *skb);
/**
* cfg80211_testmode_alloc_event_skb - allocate testmode event
* @wiphy: the wiphy
* @approxlen: an upper bound of the length of the data that will
* be put into the skb
* @gfp: allocation flags
*
* This function allocates and pre-fills an skb for an event on the
* testmode multicast group.
*
* The returned skb (or %NULL if any errors happen) is set up in the
* same way as with cfg80211_testmode_alloc_reply_skb() but prepared
* for an event. As there, you should simply add data to it that will
* then end up in the %NL80211_ATTR_TESTDATA attribute. Again, you must
* not modify the skb in any other way.
*
* When done filling the skb, call cfg80211_testmode_event() with the
* skb to send the event.
*/
struct sk_buff *cfg80211_testmode_alloc_event_skb(struct wiphy *wiphy,
int approxlen, gfp_t gfp);
/**
* cfg80211_testmode_event - send the event
* @skb: The skb, must have been allocated with
* cfg80211_testmode_alloc_event_skb()
* @gfp: allocation flags
*
* This function sends the given @skb, which must have been allocated
* by cfg80211_testmode_alloc_event_skb(), as an event. It always
* consumes it.
*/
void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp);
#define CFG80211_TESTMODE_CMD(cmd) .testmode_cmd = (cmd),
#else
#define CFG80211_TESTMODE_CMD(cmd)
#endif
/**
* cfg80211_connect_result - notify cfg80211 of connection result
*
* @dev: network device
* @bssid: the BSSID of the AP
* @req_ie: association request IEs (maybe be %NULL)
* @req_ie_len: association request IEs length
* @resp_ie: association response IEs (may be %NULL)
* @resp_ie_len: assoc response IEs length
* @status: status code, 0 for successful connection, use
* %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
* the real status code for failures.
* @gfp: allocation flags
*
* It should be called by the underlying driver whenever connect() has
* succeeded.
*/
void cfg80211_connect_result(struct net_device *dev, const u8 *bssid,
const u8 *req_ie, size_t req_ie_len,
const u8 *resp_ie, size_t resp_ie_len,
u16 status, gfp_t gfp);
/**
* cfg80211_roamed - notify cfg80211 of roaming
*
* @dev: network device
* @bssid: the BSSID of the new AP
* @req_ie: association request IEs (maybe be %NULL)
* @req_ie_len: association request IEs length
* @resp_ie: association response IEs (may be %NULL)
* @resp_ie_len: assoc response IEs length
* @gfp: allocation flags
*
* It should be called by the underlying driver whenever it roamed
* from one AP to another while connected.
*/
void cfg80211_roamed(struct net_device *dev, const u8 *bssid,
const u8 *req_ie, size_t req_ie_len,
const u8 *resp_ie, size_t resp_ie_len, gfp_t gfp);
/**
* cfg80211_disconnected - notify cfg80211 that connection was dropped
*
* @dev: network device
* @ie: information elements of the deauth/disassoc frame (may be %NULL)
* @ie_len: length of IEs
* @reason: reason code for the disconnection, set it to 0 if unknown
* @gfp: allocation flags
*
* After it calls this function, the driver should enter an idle state
* and not try to connect to any AP any more.
*/
void cfg80211_disconnected(struct net_device *dev, u16 reason,
u8 *ie, size_t ie_len, gfp_t gfp);
#endif /* __NET_CFG80211_H */