| /****************************************************************************/ |
| |
| /* |
| * m5249sim.h -- ColdFire 5249 System Integration Module support. |
| * |
| * (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com) |
| */ |
| |
| /****************************************************************************/ |
| #ifndef m5249sim_h |
| #define m5249sim_h |
| /****************************************************************************/ |
| |
| /* |
| * Define the 5249 SIM register set addresses. |
| */ |
| #define MCFSIM_RSR 0x00 /* Reset Status reg (r/w) */ |
| #define MCFSIM_SYPCR 0x01 /* System Protection reg (r/w)*/ |
| #define MCFSIM_SWIVR 0x02 /* SW Watchdog intr reg (r/w) */ |
| #define MCFSIM_SWSR 0x03 /* SW Watchdog service (r/w) */ |
| #define MCFSIM_PAR 0x04 /* Pin Assignment reg (r/w) */ |
| #define MCFSIM_IRQPAR 0x06 /* Interrupt Assignment reg (r/w) */ |
| #define MCFSIM_MPARK 0x0C /* BUS Master Control Reg*/ |
| #define MCFSIM_IPR 0x40 /* Interrupt Pend reg (r/w) */ |
| #define MCFSIM_IMR 0x44 /* Interrupt Mask reg (r/w) */ |
| #define MCFSIM_AVR 0x4b /* Autovector Ctrl reg (r/w) */ |
| #define MCFSIM_ICR0 0x4c /* Intr Ctrl reg 0 (r/w) */ |
| #define MCFSIM_ICR1 0x4d /* Intr Ctrl reg 1 (r/w) */ |
| #define MCFSIM_ICR2 0x4e /* Intr Ctrl reg 2 (r/w) */ |
| #define MCFSIM_ICR3 0x4f /* Intr Ctrl reg 3 (r/w) */ |
| #define MCFSIM_ICR4 0x50 /* Intr Ctrl reg 4 (r/w) */ |
| #define MCFSIM_ICR5 0x51 /* Intr Ctrl reg 5 (r/w) */ |
| #define MCFSIM_ICR6 0x52 /* Intr Ctrl reg 6 (r/w) */ |
| #define MCFSIM_ICR7 0x53 /* Intr Ctrl reg 7 (r/w) */ |
| #define MCFSIM_ICR8 0x54 /* Intr Ctrl reg 8 (r/w) */ |
| #define MCFSIM_ICR9 0x55 /* Intr Ctrl reg 9 (r/w) */ |
| #define MCFSIM_ICR10 0x56 /* Intr Ctrl reg 10 (r/w) */ |
| #define MCFSIM_ICR11 0x57 /* Intr Ctrl reg 11 (r/w) */ |
| |
| #define MCFSIM_CSAR0 0x80 /* CS 0 Address 0 reg (r/w) */ |
| #define MCFSIM_CSMR0 0x84 /* CS 0 Mask 0 reg (r/w) */ |
| #define MCFSIM_CSCR0 0x8a /* CS 0 Control reg (r/w) */ |
| #define MCFSIM_CSAR1 0x8c /* CS 1 Address reg (r/w) */ |
| #define MCFSIM_CSMR1 0x90 /* CS 1 Mask reg (r/w) */ |
| #define MCFSIM_CSCR1 0x96 /* CS 1 Control reg (r/w) */ |
| #define MCFSIM_CSAR2 0x98 /* CS 2 Address reg (r/w) */ |
| #define MCFSIM_CSMR2 0x9c /* CS 2 Mask reg (r/w) */ |
| #define MCFSIM_CSCR2 0xa2 /* CS 2 Control reg (r/w) */ |
| #define MCFSIM_CSAR3 0xa4 /* CS 3 Address reg (r/w) */ |
| #define MCFSIM_CSMR3 0xa8 /* CS 3 Mask reg (r/w) */ |
| #define MCFSIM_CSCR3 0xae /* CS 3 Control reg (r/w) */ |
| |
| #define MCFSIM_DCR 0x100 /* DRAM Control reg (r/w) */ |
| #define MCFSIM_DACR0 0x108 /* DRAM 0 Addr and Ctrl (r/w) */ |
| #define MCFSIM_DMR0 0x10c /* DRAM 0 Mask reg (r/w) */ |
| #define MCFSIM_DACR1 0x110 /* DRAM 1 Addr and Ctrl (r/w) */ |
| #define MCFSIM_DMR1 0x114 /* DRAM 1 Mask reg (r/w) */ |
| |
| |
| /* |
| * Some symbol defines for the above... |
| */ |
| #define MCFSIM_SWDICR MCFSIM_ICR0 /* Watchdog timer ICR */ |
| #define MCFSIM_TIMER1ICR MCFSIM_ICR1 /* Timer 1 ICR */ |
| #define MCFSIM_TIMER2ICR MCFSIM_ICR2 /* Timer 2 ICR */ |
| #define MCFSIM_UART1ICR MCFSIM_ICR4 /* UART 1 ICR */ |
| #define MCFSIM_UART2ICR MCFSIM_ICR5 /* UART 2 ICR */ |
| #define MCFSIM_DMA0ICR MCFSIM_ICR6 /* DMA 0 ICR */ |
| #define MCFSIM_DMA1ICR MCFSIM_ICR7 /* DMA 1 ICR */ |
| #define MCFSIM_DMA2ICR MCFSIM_ICR8 /* DMA 2 ICR */ |
| #define MCFSIM_DMA3ICR MCFSIM_ICR9 /* DMA 3 ICR */ |
| |
| /* |
| * General purpose IO registers (in MBAR2). |
| */ |
| #define MCFSIM2_GPIOREAD (MCF_MBAR2 + 0x000) /* GPIO read values */ |
| #define MCFSIM2_GPIOWRITE (MCF_MBAR2 + 0x004) /* GPIO write values */ |
| #define MCFSIM2_GPIOENABLE (MCF_MBAR2 + 0x008) /* GPIO enabled */ |
| #define MCFSIM2_GPIOFUNC (MCF_MBAR2 + 0x00C) /* GPIO function */ |
| #define MCFSIM2_GPIO1READ (MCF_MBAR2 + 0x0B0) /* GPIO1 read values */ |
| #define MCFSIM2_GPIO1WRITE (MCF_MBAR2 + 0x0B4) /* GPIO1 write values */ |
| #define MCFSIM2_GPIO1ENABLE (MCF_MBAR2 + 0x0B8) /* GPIO1 enabled */ |
| #define MCFSIM2_GPIO1FUNC (MCF_MBAR2 + 0x0BC) /* GPIO1 function */ |
| |
| #define MCFSIM2_GPIOINTSTAT 0xc0 /* GPIO interrupt status */ |
| #define MCFSIM2_GPIOINTCLEAR 0xc0 /* GPIO interrupt clear */ |
| #define MCFSIM2_GPIOINTENABLE 0xc4 /* GPIO interrupt enable */ |
| |
| #define MCFSIM2_INTLEVEL1 0x140 /* Interrupt level reg 1 */ |
| #define MCFSIM2_INTLEVEL2 0x144 /* Interrupt level reg 2 */ |
| #define MCFSIM2_INTLEVEL3 0x148 /* Interrupt level reg 3 */ |
| #define MCFSIM2_INTLEVEL4 0x14c /* Interrupt level reg 4 */ |
| #define MCFSIM2_INTLEVEL5 0x150 /* Interrupt level reg 5 */ |
| #define MCFSIM2_INTLEVEL6 0x154 /* Interrupt level reg 6 */ |
| #define MCFSIM2_INTLEVEL7 0x158 /* Interrupt level reg 7 */ |
| #define MCFSIM2_INTLEVEL8 0x15c /* Interrupt level reg 8 */ |
| |
| #define MCFSIM2_DMAROUTE 0x188 /* DMA routing */ |
| |
| #define MCFSIM2_IDECONFIG1 0x18c /* IDEconfig1 */ |
| #define MCFSIM2_IDECONFIG2 0x190 /* IDEconfig2 */ |
| |
| /* |
| * Generic GPIO support |
| */ |
| #define MCFGPIO_PIN_MAX 64 |
| #define MCFGPIO_IRQ_MAX -1 |
| #define MCFGPIO_IRQ_VECBASE -1 |
| |
| /****************************************************************************/ |
| |
| #ifdef __ASSEMBLER__ |
| |
| /* |
| * The M5249C3 board needs a little help getting all its SIM devices |
| * initialized at kernel start time. dBUG doesn't set much up, so |
| * we need to do it manually. |
| */ |
| .macro m5249c3_setup |
| /* |
| * Set MBAR1 and MBAR2, just incase they are not set. |
| */ |
| movel #0x10000001,%a0 |
| movec %a0,%MBAR /* map MBAR region */ |
| subql #1,%a0 /* get MBAR address in a0 */ |
| |
| movel #0x80000001,%a1 |
| movec %a1,#3086 /* map MBAR2 region */ |
| subql #1,%a1 /* get MBAR2 address in a1 */ |
| |
| /* |
| * Move secondary interrupts to base at 128. |
| */ |
| moveb #0x80,%d0 |
| moveb %d0,0x16b(%a1) /* interrupt base register */ |
| |
| /* |
| * Work around broken CSMR0/DRAM vector problem. |
| */ |
| movel #0x001F0021,%d0 /* disable C/I bit */ |
| movel %d0,0x84(%a0) /* set CSMR0 */ |
| |
| /* |
| * Disable the PLL firstly. (Who knows what state it is |
| * in here!). |
| */ |
| movel 0x180(%a1),%d0 /* get current PLL value */ |
| andl #0xfffffffe,%d0 /* PLL bypass first */ |
| movel %d0,0x180(%a1) /* set PLL register */ |
| nop |
| |
| #if CONFIG_CLOCK_FREQ == 140000000 |
| /* |
| * Set initial clock frequency. This assumes M5249C3 board |
| * is fitted with 11.2896MHz crystal. It will program the |
| * PLL for 140MHz. Lets go fast :-) |
| */ |
| movel #0x125a40f0,%d0 /* set for 140MHz */ |
| movel %d0,0x180(%a1) /* set PLL register */ |
| orl #0x1,%d0 |
| movel %d0,0x180(%a1) /* set PLL register */ |
| #endif |
| |
| /* |
| * Setup CS1 for ethernet controller. |
| * (Setup as per M5249C3 doco). |
| */ |
| movel #0xe0000000,%d0 /* CS1 mapped at 0xe0000000 */ |
| movel %d0,0x8c(%a0) |
| movel #0x001f0021,%d0 /* CS1 size of 1Mb */ |
| movel %d0,0x90(%a0) |
| movew #0x0080,%d0 /* CS1 = 16bit port, AA */ |
| movew %d0,0x96(%a0) |
| |
| /* |
| * Setup CS2 for IDE interface. |
| */ |
| movel #0x50000000,%d0 /* CS2 mapped at 0x50000000 */ |
| movel %d0,0x98(%a0) |
| movel #0x001f0001,%d0 /* CS2 size of 1MB */ |
| movel %d0,0x9c(%a0) |
| movew #0x0080,%d0 /* CS2 = 16bit, TA */ |
| movew %d0,0xa2(%a0) |
| |
| movel #0x00107000,%d0 /* IDEconfig1 */ |
| movel %d0,0x18c(%a1) |
| movel #0x000c0400,%d0 /* IDEconfig2 */ |
| movel %d0,0x190(%a1) |
| |
| movel #0x00080000,%d0 /* GPIO19, IDE reset bit */ |
| orl %d0,0xc(%a1) /* function GPIO19 */ |
| orl %d0,0x8(%a1) /* enable GPIO19 as output */ |
| orl %d0,0x4(%a1) /* de-assert IDE reset */ |
| .endm |
| |
| #define PLATFORM_SETUP m5249c3_setup |
| |
| #endif /* __ASSEMBLER__ */ |
| |
| /****************************************************************************/ |
| #endif /* m5249sim_h */ |