| /* |
| * Copyright (C) 2014 Russell King |
| */ |
| #include "imx6qdl-microsom.dtsi" |
| #include "imx6qdl-microsom-ar8035.dtsi" |
| |
| / { |
| ir_recv: ir-receiver { |
| compatible = "gpio-ir-receiver"; |
| gpios = <&gpio3 9 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_ir>; |
| }; |
| |
| pwmleds { |
| compatible = "pwm-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_pwm1>; |
| |
| front { |
| active-low; |
| label = "imx6:red:front"; |
| max-brightness = <248>; |
| pwms = <&pwm1 0 50000>; |
| }; |
| }; |
| |
| regulators { |
| compatible = "simple-bus"; |
| |
| reg_3p3v: 3p3v { |
| compatible = "regulator-fixed"; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_usbh1_vbus: usb-h1-vbus { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio1 0 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_usbh1_vbus>; |
| regulator-name = "usb_h1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_usbotg_vbus: usb-otg-vbus { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio3 22 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_usbotg_vbus>; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| }; |
| |
| sound-spdif { |
| compatible = "fsl,imx-audio-spdif"; |
| model = "imx-spdif"; |
| /* IMX6 doesn't implement this yet */ |
| spdif-controller = <&spdif>; |
| spdif-out; |
| }; |
| }; |
| |
| &hdmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_hdmi>; |
| ddc-i2c-bus = <&i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_i2c3>; |
| |
| status = "okay"; |
| |
| rtc: pcf8523@68 { |
| compatible = "nxp,pcf8523"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| &iomuxc { |
| cubox_i { |
| pinctrl_cubox_i_hdmi: cubox-i-hdmi { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 |
| >; |
| }; |
| |
| pinctrl_cubox_i_i2c2: cubox-i-i2c2 { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_cubox_i_i2c3: cubox-i-i2c3 { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_cubox_i_ir: cubox-i-ir { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000 |
| >; |
| }; |
| |
| pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led { |
| fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>; |
| }; |
| |
| pinctrl_cubox_i_spdif: cubox-i-spdif { |
| fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>; |
| }; |
| |
| pinctrl_cubox_i_usbh1: cubox-i-usbh1 { |
| fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>; |
| }; |
| |
| pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus { |
| fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>; |
| }; |
| |
| pinctrl_cubox_i_usbotg: cubox-i-usbotg { |
| /* |
| * The Cubox-i pulls ID low, but as it's pointless |
| * leaving it as a pull-up, even if it is just 10uA. |
| */ |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059 |
| MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus { |
| fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>; |
| }; |
| |
| pinctrl_cubox_i_usdhc2_aux: cubox-i-usdhc2-aux { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071 |
| MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071 |
| >; |
| }; |
| |
| pinctrl_cubox_i_usdhc2: cubox-i-usdhc2 { |
| fsl,pins = < |
| MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 |
| MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 |
| MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 |
| MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 |
| MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 |
| MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059 |
| >; |
| }; |
| }; |
| }; |
| |
| &spdif { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_spdif>; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_usbh1>; |
| vbus-supply = <®_usbh1_vbus>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_usbotg>; |
| vbus-supply = <®_usbotg_vbus>; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_cubox_i_usdhc2_aux &pinctrl_cubox_i_usdhc2>; |
| vmmc-supply = <®_3p3v>; |
| cd-gpios = <&gpio1 4 0>; |
| status = "okay"; |
| }; |