| /* |
| * Copyright (c) 2018, 2020, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| &msm_gpio { |
| SY7807_pins { |
| pins = "gpio32"; |
| qcom,num-grp-pins = <1>; |
| qcom,pin-func = <2>; |
| label = "SY7807_pins"; |
| SY7807_default: en_default { |
| mux { |
| pins = "gpio32"; |
| function = "gpio"; |
| }; |
| |
| configs { |
| pins = "gpio32"; |
| drive-strength = <0x2>; |
| bias-pull-down; |
| }; |
| |
| }; |
| }; |
| }; |
| |
| &soc { |
| flash_SY7807:flashlight { |
| compatible = "qcom,leds-gpio-flash"; |
| status = "okay"; |
| pinctrl-names = "flash_default"; |
| pinctrl-0 = <&SY7807_default &flash_en_default>; |
| qcom,flash-en = <&pm8909_gpios 4 0>; |
| qcom,flash-now = <&msm_gpio 32 0>; |
| clocks = <&clock_gcc clk_gcc_camss_gp1_clk>, |
| <&clock_gcc clk_camss_gp1_clk_src>; |
| clock-names = "flash_now_clk", "flash_now_duty_cycle_clk"; |
| qcom,op-seq = "flash_en", "flash_now"; |
| qcom,torch-seq-val = <1 0>; |
| qcom,flash-seq-val = <0 1>; |
| qcom,duty-cycle = <0 30>; |
| qcom,clk-freq = <0 150000>; |
| linux,name = "flashlight"; |
| linux,default-trigger = "flashlight-trigger"; |
| }; |
| led_flash0: qcom,camera-led-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-led-flash"; |
| qcom,flash-type = <3>; |
| qcom,flash-source = <&flash_SY7807>; |
| qcom,torch-source = <&flash_SY7807>; |
| }; |
| }; |
| |
| &i2c_3 { |
| |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x3>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&pm8909_l8>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-type = <0>; |
| qcom,cam-vreg-min-voltage = <2850000>; |
| qcom,cam-vreg-max-voltage = <2900000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| }; |
| |
| eeprom0: qcom,eeprom@6d{ |
| cell-index = <0>; |
| reg = <0x6d>; |
| qcom,eeprom-name = "sunrise_pc0fe"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x6d>; |
| qcom,cci-master = <0>; |
| |
| qcom,num-blocks = <10>; |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x5002 2 0xa8 1 1>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <0 0x0 2 0 1 0>; |
| qcom,page2 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <0 0x0 2 0 1 0>; |
| qcom,page3 = <1 0x3d88 2 0x70 1 1>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <0 0x3d00 2 0 1 0>; |
| qcom,page4 = <1 0x3d89 2 0x10 1 1>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <0 0x3d00 2 0 1 0>; |
| qcom,page5 = <1 0x3d8a 2 0x70 1 1>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <0 0x3d00 2 0 1 0>; |
| qcom,page6 = <1 0x3d8b 2 0x29 1 1>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <0 0x3d00 2 0 1 0>; |
| qcom,page7 = <1 0x3d81 2 0x01 1 5>; |
| qcom,poll7 = <0 0x0 2 0 1 1>; |
| qcom,mem7 = <26 0x7010 2 0 1 1>; |
| qcom,page8 = <1 0x5002 2 0xaa 1 1>; |
| qcom,poll8 = <0 0x0 2 0 1 1>; |
| qcom,mem8 = <0 0x0 2 0 1 0>; |
| qcom,page9 = <1 0x0100 2 0x00 1 1>; |
| qcom,poll9 = <0 0x0 2 0 1 1>; |
| qcom,mem9 = <0 0x0 2 0 1 0>; |
| |
| cam_vdig-supply = <&pm8909_l2>; |
| cam_vana-supply = <&pm8909_l17>; |
| cam_vio-supply = <&pm8909_l6>; |
| cam_vaf-supply = <&pm8909_l8>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2850000 2900000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000 100000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default |
| &cam_sensor_rear_default>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep>; |
| gpios = <&msm_gpio 26 0>, |
| <&msm_gpio 35 0>, |
| <&msm_gpio 34 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_vreg", |
| "sensor_gpio", "sensor_gpio", |
| "sensor_clk"; |
| qcom,cam-power-seq-val = "cam_vio", |
| "cam_vana", "cam_vdig", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby", |
| "sensor_cam_mclk" ; |
| qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <10 10 10 10 10 5>; |
| |
| clocks = <&clock_gcc clk_mclk0_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk0_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x2>; |
| qcom,special-support-sensors="ov5670_30010a3", "gc2365"; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| cam_vana-supply = <&pm8909_l17>; |
| cam_vio-supply = <&pm8909_l6>; |
| cam_vaf-supply = <&pm8909_l8>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 0 0>; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1800000 2850000 2900000>; |
| qcom,cam-vreg-op-mode = <0 80000 100000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default |
| &cam_sensor_rear_default>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep>; |
| gpios = <&msm_gpio 26 0>, |
| <&msm_gpio 35 0>, |
| <&msm_gpio 34 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc clk_mclk0_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk0_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x1>; |
| qcom,special-support-sensors="ov2680_cht852b", "gc030a"; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| cam_vana-supply = <&pm8909_l17>; |
| cam_vio-supply = <&pm8909_l6>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 0>; |
| qcom,cam-vreg-min-voltage = <1800000 2800000>; |
| qcom,cam-vreg-max-voltage = <1800000 2850000>; |
| qcom,cam-vreg-op-mode = <0 80000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = |
| <&cam_sensor_mclk1_default &cam_sensor_front_default>; |
| pinctrl-1 = <&cam_sensor_mclk1_sleep &cam_sensor_front_sleep>; |
| gpios = <&msm_gpio 27 0>, |
| <&msm_gpio 28 0>, |
| <&msm_gpio 33 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc clk_mclk1_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk1_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| }; |