blob: aaf53a81e78bf62252890ed9c623530f8aee0bbe [file] [log] [blame]
/*
* Copyright (c) 2005-2011 Atheros Communications Inc.
* Copyright (c) 2011-2013 Qualcomm Atheros, Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#ifndef __TARGADDRS_H__
#define __TARGADDRS_H__
#include "hw.h"
/*
* xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
* host_interest structure. It must match the address of the _host_interest
* symbol (see linker script).
*
* Host Interest is shared between Host and Target in order to coordinate
* between the two, and is intended to remain constant (with additions only
* at the end) across software releases.
*
* All addresses are available here so that it's possible to
* write a single binary that works with all Target Types.
* May be used in assembler code as well as C.
*/
#define QCA988X_HOST_INTEREST_ADDRESS 0x00400800
#define HOST_INTEREST_MAX_SIZE 0x200
/*
* These are items that the Host may need to access via BMI or via the
* Diagnostic Window. The position of items in this structure must remain
* constant across firmware revisions! Types for each item must be fixed
* size across target and host platforms. More items may be added at the end.
*/
struct host_interest {
/*
* Pointer to application-defined area, if any.
* Set by Target application during startup.
*/
u32 hi_app_host_interest; /* 0x00 */
/* Pointer to register dump area, valid after Target crash. */
u32 hi_failure_state; /* 0x04 */
/* Pointer to debug logging header */
u32 hi_dbglog_hdr; /* 0x08 */
u32 hi_unused0c; /* 0x0c */
/*
* General-purpose flag bits, similar to SOC_OPTION_* flags.
* Can be used by application rather than by OS.
*/
u32 hi_option_flag; /* 0x10 */
/*
* Boolean that determines whether or not to
* display messages on the serial port.
*/
u32 hi_serial_enable; /* 0x14 */
/* Start address of DataSet index, if any */
u32 hi_dset_list_head; /* 0x18 */
/* Override Target application start address */
u32 hi_app_start; /* 0x1c */
/* Clock and voltage tuning */
u32 hi_skip_clock_init; /* 0x20 */
u32 hi_core_clock_setting; /* 0x24 */
u32 hi_cpu_clock_setting; /* 0x28 */
u32 hi_system_sleep_setting; /* 0x2c */
u32 hi_xtal_control_setting; /* 0x30 */
u32 hi_pll_ctrl_setting_24ghz; /* 0x34 */
u32 hi_pll_ctrl_setting_5ghz; /* 0x38 */
u32 hi_ref_voltage_trim_setting; /* 0x3c */
u32 hi_clock_info; /* 0x40 */
/* Host uses BE CPU or not */
u32 hi_be; /* 0x44 */
u32 hi_stack; /* normal stack */ /* 0x48 */
u32 hi_err_stack; /* error stack */ /* 0x4c */
u32 hi_desired_cpu_speed_hz; /* 0x50 */
/* Pointer to Board Data */
u32 hi_board_data; /* 0x54 */
/*
* Indication of Board Data state:
* 0: board data is not yet initialized.
* 1: board data is initialized; unknown size
* >1: number of bytes of initialized board data
*/
u32 hi_board_data_initialized; /* 0x58 */
u32 hi_dset_ram_index_table; /* 0x5c */
u32 hi_desired_baud_rate; /* 0x60 */
u32 hi_dbglog_config; /* 0x64 */
u32 hi_end_ram_reserve_sz; /* 0x68 */
u32 hi_mbox_io_block_sz; /* 0x6c */
u32 hi_num_bpatch_streams; /* 0x70 -- unused */
u32 hi_mbox_isr_yield_limit; /* 0x74 */
u32 hi_refclk_hz; /* 0x78 */
u32 hi_ext_clk_detected; /* 0x7c */
u32 hi_dbg_uart_txpin; /* 0x80 */
u32 hi_dbg_uart_rxpin; /* 0x84 */
u32 hi_hci_uart_baud; /* 0x88 */
u32 hi_hci_uart_pin_assignments; /* 0x8C */
u32 hi_hci_uart_baud_scale_val; /* 0x90 */
u32 hi_hci_uart_baud_step_val; /* 0x94 */
u32 hi_allocram_start; /* 0x98 */
u32 hi_allocram_sz; /* 0x9c */
u32 hi_hci_bridge_flags; /* 0xa0 */
u32 hi_hci_uart_support_pins; /* 0xa4 */
u32 hi_hci_uart_pwr_mgmt_params; /* 0xa8 */
/*
* 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
* [31:16]: wakeup timeout in ms
*/
/* Pointer to extended board Data */
u32 hi_board_ext_data; /* 0xac */
u32 hi_board_ext_data_config; /* 0xb0 */
/*
* Bit [0] : valid
* Bit[31:16: size
*/
/*
* hi_reset_flag is used to do some stuff when target reset.
* such as restore app_start after warm reset or
* preserve host Interest area, or preserve ROM data, literals etc.
*/
u32 hi_reset_flag; /* 0xb4 */
/* indicate hi_reset_flag is valid */
u32 hi_reset_flag_valid; /* 0xb8 */
u32 hi_hci_uart_pwr_mgmt_params_ext; /* 0xbc */
/* 0xbc - [31:0]: idle timeout in ms */
/* ACS flags */
u32 hi_acs_flags; /* 0xc0 */
u32 hi_console_flags; /* 0xc4 */
u32 hi_nvram_state; /* 0xc8 */
u32 hi_option_flag2; /* 0xcc */
/* If non-zero, override values sent to Host in WMI_READY event. */
u32 hi_sw_version_override; /* 0xd0 */
u32 hi_abi_version_override; /* 0xd4 */
/*
* Percentage of high priority RX traffic to total expected RX traffic
* applicable only to ar6004
*/
u32 hi_hp_rx_traffic_ratio; /* 0xd8 */
/* test applications flags */
u32 hi_test_apps_related; /* 0xdc */
/* location of test script */
u32 hi_ota_testscript; /* 0xe0 */
/* location of CAL data */
u32 hi_cal_data; /* 0xe4 */
/* Number of packet log buffers */
u32 hi_pktlog_num_buffers; /* 0xe8 */
/* wow extension configuration */
u32 hi_wow_ext_config; /* 0xec */
u32 hi_pwr_save_flags; /* 0xf0 */
/* Spatial Multiplexing Power Save (SMPS) options */
u32 hi_smps_options; /* 0xf4 */
/* Interconnect-specific state */
u32 hi_interconnect_state; /* 0xf8 */
/* Coex configuration flags */
u32 hi_coex_config; /* 0xfc */
/* Early allocation support */
u32 hi_early_alloc; /* 0x100 */
/* FW swap field */
/*
* Bits of this 32bit word will be used to pass specific swap
* instruction to FW
*/
/*
* Bit 0 -- AP Nart descriptor no swap. When this bit is set
* FW will not swap TX descriptor. Meaning packets are formed
* on the target processor.
*/
/* Bit 1 - unused */
u32 hi_fw_swap; /* 0x104 */
} __packed;
#define HI_ITEM(item) offsetof(struct host_interest, item)
/* Bits defined in hi_option_flag */
/* Enable timer workaround */
#define HI_OPTION_TIMER_WAR 0x01
/* Limit BMI command credits */
#define HI_OPTION_BMI_CRED_LIMIT 0x02
/* Relay Dot11 hdr to/from host */
#define HI_OPTION_RELAY_DOT11_HDR 0x04
/* MAC addr method 0-locally administred 1-globally unique addrs */
#define HI_OPTION_MAC_ADDR_METHOD 0x08
/* Firmware Bridging */
#define HI_OPTION_FW_BRIDGE 0x10
/* Enable CPU profiling */
#define HI_OPTION_ENABLE_PROFILE 0x20
/* Disable debug logging */
#define HI_OPTION_DISABLE_DBGLOG 0x40
/* Skip Era Tracking */
#define HI_OPTION_SKIP_ERA_TRACKING 0x80
/* Disable PAPRD (debug) */
#define HI_OPTION_PAPRD_DISABLE 0x100
#define HI_OPTION_NUM_DEV_LSB 0x200
#define HI_OPTION_NUM_DEV_MSB 0x800
#define HI_OPTION_DEV_MODE_LSB 0x1000
#define HI_OPTION_DEV_MODE_MSB 0x8000000
/* Disable LowFreq Timer Stabilization */
#define HI_OPTION_NO_LFT_STBL 0x10000000
/* Skip regulatory scan */
#define HI_OPTION_SKIP_REG_SCAN 0x20000000
/*
* Do regulatory scan during init before
* sending WMI ready event to host
*/
#define HI_OPTION_INIT_REG_SCAN 0x40000000
/* REV6: Do not adjust memory map */
#define HI_OPTION_SKIP_MEMMAP 0x80000000
#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
/* 2 bits of hi_option_flag are used to represent 3 modes */
#define HI_OPTION_FW_MODE_IBSS 0x0 /* IBSS Mode */
#define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
#define HI_OPTION_FW_MODE_AP 0x2 /* AP Mode */
#define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */
/* 2 bits of hi_option flag are usedto represent 4 submodes */
#define HI_OPTION_FW_SUBMODE_NONE 0x0 /* Normal mode */
#define HI_OPTION_FW_SUBMODE_P2PDEV 0x1 /* p2p device mode */
#define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
#define HI_OPTION_FW_SUBMODE_P2PGO 0x3 /* p2p go mode */
/* Num dev Mask */
#define HI_OPTION_NUM_DEV_MASK 0x7
#define HI_OPTION_NUM_DEV_SHIFT 0x9
/* firmware bridging */
#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
/*
Fw Mode/SubMode Mask
|-----------------------------------------------------------------------------|
| SUB | SUB | SUB | SUB | | | | |
|MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]|
| (2) | (2) | (2) | (2) | (2) | (2) | (2) | (2) |
|-----------------------------------------------------------------------------|
*/
#define HI_OPTION_FW_MODE_BITS 0x2
#define HI_OPTION_FW_MODE_MASK 0x3
#define HI_OPTION_FW_MODE_SHIFT 0xC
#define HI_OPTION_ALL_FW_MODE_MASK 0xFF
#define HI_OPTION_FW_SUBMODE_BITS 0x2
#define HI_OPTION_FW_SUBMODE_MASK 0x3
#define HI_OPTION_FW_SUBMODE_SHIFT 0x14
#define HI_OPTION_ALL_FW_SUBMODE_MASK 0xFF00
#define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
/* hi_option_flag2 options */
#define HI_OPTION_OFFLOAD_AMSDU 0x01
#define HI_OPTION_DFS_SUPPORT 0x02 /* Enable DFS support */
#define HI_OPTION_ENABLE_RFKILL 0x04 /* RFKill Enable Feature*/
#define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */
#define HI_OPTION_EARLY_CFG_DONE 0x10 /* Early configuration is complete */
#define HI_OPTION_RF_KILL_SHIFT 0x2
#define HI_OPTION_RF_KILL_MASK 0x1
/* hi_reset_flag */
/* preserve App Start address */
#define HI_RESET_FLAG_PRESERVE_APP_START 0x01
/* preserve host interest */
#define HI_RESET_FLAG_PRESERVE_HOST_INTEREST 0x02
/* preserve ROM data */
#define HI_RESET_FLAG_PRESERVE_ROMDATA 0x04
#define HI_RESET_FLAG_PRESERVE_NVRAM_STATE 0x08
#define HI_RESET_FLAG_PRESERVE_BOOT_INFO 0x10
#define HI_RESET_FLAG_WARM_RESET 0x20
/* define hi_fw_swap bits */
#define HI_DESC_IN_FW_BIT 0x01
/* indicate the reset flag is valid */
#define HI_RESET_FLAG_IS_VALID 0x12345678
/* ACS is enabled */
#define HI_ACS_FLAGS_ENABLED (1 << 0)
/* Use physical WWAN device */
#define HI_ACS_FLAGS_USE_WWAN (1 << 1)
/* Use test VAP */
#define HI_ACS_FLAGS_TEST_VAP (1 << 2)
/*
* CONSOLE FLAGS
*
* Bit Range Meaning
* --------- --------------------------------
* 2..0 UART ID (0 = Default)
* 3 Baud Select (0 = 9600, 1 = 115200)
* 30..4 Reserved
* 31 Enable Console
*
*/
#define HI_CONSOLE_FLAGS_ENABLE (1 << 31)
#define HI_CONSOLE_FLAGS_UART_MASK (0x7)
#define HI_CONSOLE_FLAGS_UART_SHIFT 0
#define HI_CONSOLE_FLAGS_BAUD_SELECT (1 << 3)
/* SM power save options */
#define HI_SMPS_ALLOW_MASK (0x00000001)
#define HI_SMPS_MODE_MASK (0x00000002)
#define HI_SMPS_MODE_STATIC (0x00000000)
#define HI_SMPS_MODE_DYNAMIC (0x00000002)
#define HI_SMPS_DISABLE_AUTO_MODE (0x00000004)
#define HI_SMPS_DATA_THRESH_MASK (0x000007f8)
#define HI_SMPS_DATA_THRESH_SHIFT (3)
#define HI_SMPS_RSSI_THRESH_MASK (0x0007f800)
#define HI_SMPS_RSSI_THRESH_SHIFT (11)
#define HI_SMPS_LOWPWR_CM_MASK (0x00380000)
#define HI_SMPS_LOWPWR_CM_SHIFT (15)
#define HI_SMPS_HIPWR_CM_MASK (0x03c00000)
#define HI_SMPS_HIPWR_CM_SHIFT (19)
/*
* WOW Extension configuration
*
* Bit Range Meaning
* --------- --------------------------------
* 8..0 Size of each WOW pattern (max 511)
* 15..9 Number of patterns per list (max 127)
* 17..16 Number of lists (max 4)
* 30..18 Reserved
* 31 Enabled
*
* set values (except enable) to zeros for default settings
*/
#define HI_WOW_EXT_ENABLED_MASK (1 << 31)
#define HI_WOW_EXT_NUM_LIST_SHIFT 16
#define HI_WOW_EXT_NUM_LIST_MASK (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT)
#define HI_WOW_EXT_NUM_PATTERNS_SHIFT 9
#define HI_WOW_EXT_NUM_PATTERNS_MASK (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT)
#define HI_WOW_EXT_PATTERN_SIZE_SHIFT 0
#define HI_WOW_EXT_PATTERN_SIZE_MASK (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT)
#define HI_WOW_EXT_MAKE_CONFIG(num_lists, count, size) \
((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & \
HI_WOW_EXT_NUM_LIST_MASK) | \
(((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & \
HI_WOW_EXT_NUM_PATTERNS_MASK) | \
(((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & \
HI_WOW_EXT_PATTERN_SIZE_MASK))
#define HI_WOW_EXT_GET_NUM_LISTS(config) \
(((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT)
#define HI_WOW_EXT_GET_NUM_PATTERNS(config) \
(((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> \
HI_WOW_EXT_NUM_PATTERNS_SHIFT)
#define HI_WOW_EXT_GET_PATTERN_SIZE(config) \
(((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> \
HI_WOW_EXT_PATTERN_SIZE_SHIFT)
/*
* Early allocation configuration
* Support RAM bank configuration before BMI done and this eases the memory
* allocation at very early stage
* Bit Range Meaning
* --------- ----------------------------------
* [0:3] number of bank assigned to be IRAM
* [4:15] reserved
* [16:31] magic number
*
* Note:
* 1. target firmware would check magic number and if it's a match, firmware
* would consider the bits[0:15] are valid and base on that to calculate
* the end of DRAM. Early allocation would be located at that area and
* may be reclaimed when necesary
* 2. if no magic number is found, early allocation would happen at "_end"
* symbol of ROM which is located before the app-data and might NOT be
* re-claimable. If this is adopted, link script should keep this in
* mind to avoid data corruption.
*/
#define HI_EARLY_ALLOC_MAGIC 0x6d8a
#define HI_EARLY_ALLOC_MAGIC_MASK 0xffff0000
#define HI_EARLY_ALLOC_MAGIC_SHIFT 16
#define HI_EARLY_ALLOC_IRAM_BANKS_MASK 0x0000000f
#define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT 0
#define HI_EARLY_ALLOC_VALID() \
((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> \
HI_EARLY_ALLOC_MAGIC_SHIFT) == (HI_EARLY_ALLOC_MAGIC))
#define HI_EARLY_ALLOC_GET_IRAM_BANKS() \
(((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) \
>> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT)
/*power save flag bit definitions*/
#define HI_PWR_SAVE_LPL_ENABLED 0x1
/*b1-b3 reserved*/
/*b4-b5 : dev0 LPL type : 0 - none
1- Reduce Pwr Search
2- Reduce Pwr Listen*/
/*b6-b7 : dev1 LPL type and so on for Max 8 devices*/
#define HI_PWR_SAVE_LPL_DEV0_LSB 4
#define HI_PWR_SAVE_LPL_DEV_MASK 0x3
/*power save related utility macros*/
#define HI_LPL_ENABLED() \
((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED))
#define HI_DEV_LPL_TYPE_GET(_devix) \
(HOST_INTEREST->hi_pwr_save_flags & ((HI_PWR_SAVE_LPL_DEV_MASK) << \
(HI_PWR_SAVE_LPL_DEV0_LSB + (_devix) * 2)))
#define HOST_INTEREST_SMPS_IS_ALLOWED() \
((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK))
/* Reserve 1024 bytes for extended board data */
#define QCA988X_BOARD_DATA_SZ 7168
#define QCA988X_BOARD_EXT_DATA_SZ 0
#define QCA9887_BOARD_DATA_SZ 7168
#define QCA9887_BOARD_EXT_DATA_SZ 0
#define QCA6174_BOARD_DATA_SZ 8192
#define QCA6174_BOARD_EXT_DATA_SZ 0
#define QCA9377_BOARD_DATA_SZ QCA6174_BOARD_DATA_SZ
#define QCA9377_BOARD_EXT_DATA_SZ 0
#define QCA99X0_BOARD_DATA_SZ 12288
#define QCA99X0_BOARD_EXT_DATA_SZ 0
#define QCA4019_BOARD_DATA_SZ 12064
#define QCA4019_BOARD_EXT_DATA_SZ 0
#endif /* __TARGADDRS_H__ */