| IBM ThinkPad ACPI Extras Driver |
| |
| Version 0.8 |
| 8 November 2004 |
| |
| Borislav Deianov <borislav@users.sf.net> |
| http://ibm-acpi.sf.net/ |
| |
| |
| This is a Linux ACPI driver for the IBM ThinkPad laptops. It aims to |
| support various features of these laptops which are accessible through |
| the ACPI framework but not otherwise supported by the generic Linux |
| ACPI drivers. |
| |
| |
| Status |
| ------ |
| |
| The features currently supported are the following (see below for |
| detailed description): |
| |
| - Fn key combinations |
| - Bluetooth enable and disable |
| - video output switching, expansion control |
| - ThinkLight on and off |
| - limited docking and undocking |
| - UltraBay eject |
| - Experimental: CMOS control |
| - Experimental: LED control |
| - Experimental: ACPI sounds |
| |
| A compatibility table by model and feature is maintained on the web |
| site, http://ibm-acpi.sf.net/. I appreciate any success or failure |
| reports, especially if they add to or correct the compatibility table. |
| Please include the following information in your report: |
| |
| - ThinkPad model name |
| - a copy of your DSDT, from /proc/acpi/dsdt |
| - which driver features work and which don't |
| - the observed behavior of non-working features |
| |
| Any other comments or patches are also more than welcome. |
| |
| |
| Installation |
| ------------ |
| |
| If you are compiling this driver as included in the Linux kernel |
| sources, simply enable the CONFIG_ACPI_IBM option (Power Management / |
| ACPI / IBM ThinkPad Laptop Extras). The rest of this section describes |
| how to install this driver when downloaded from the web site. |
| |
| First, you need to get a kernel with ACPI support up and running. |
| Please refer to http://acpi.sourceforge.net/ for help with this |
| step. How successful you will be depends a lot on you ThinkPad model, |
| the kernel you are using and any additional patches applied. The |
| kernel provided with your distribution may not be good enough. I |
| needed to compile a 2.6.7 kernel with the 20040715 ACPI patch to get |
| ACPI working reliably on my ThinkPad X40. Old ThinkPad models may not |
| be supported at all. |
| |
| Assuming you have the basic ACPI support working (e.g. you can see the |
| /proc/acpi directory), follow the following steps to install this |
| driver: |
| |
| - unpack the archive: |
| |
| tar xzvf ibm-acpi-x.y.tar.gz; cd ibm-acpi-x.y |
| |
| - compile the driver: |
| |
| make |
| |
| - install the module in your kernel modules directory: |
| |
| make install |
| |
| - load the module: |
| |
| modprobe ibm_acpi |
| |
| After loading the module, check the "dmesg" output for any error messages. |
| |
| |
| Features |
| -------- |
| |
| The driver creates the /proc/acpi/ibm directory. There is a file under |
| that directory for each feature described below. Note that while the |
| driver is still in the alpha stage, the exact proc file format and |
| commands supported by the various features is guaranteed to change |
| frequently. |
| |
| Driver Version -- /proc/acpi/ibm/driver |
| -------------------------------------- |
| |
| The driver name and version. No commands can be written to this file. |
| |
| Hot Keys -- /proc/acpi/ibm/hotkey |
| --------------------------------- |
| |
| Without this driver, only the Fn-F4 key (sleep button) generates an |
| ACPI event. With the driver loaded, the hotkey feature enabled and the |
| mask set (see below), the various hot keys generate ACPI events in the |
| following format: |
| |
| ibm/hotkey HKEY 00000080 0000xxxx |
| |
| The last four digits vary depending on the key combination pressed. |
| All labeled Fn-Fx key combinations generate distinct events. In |
| addition, the lid microswitch and some docking station buttons may |
| also generate such events. |
| |
| The following commands can be written to this file: |
| |
| echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature |
| echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature |
| echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys |
| echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys |
| ... any other 4-hex-digit mask ... |
| echo reset > /proc/acpi/ibm/hotkey -- restore the original mask |
| |
| The bit mask allows some control over which hot keys generate ACPI |
| events. Not all bits in the mask can be modified. Not all bits that |
| can be modified do anything. Not all hot keys can be individually |
| controlled by the mask. Most recent ThinkPad models honor the |
| following bits (assuming the hot keys feature has been enabled): |
| |
| key bit behavior when set behavior when unset |
| |
| Fn-F3 always generates ACPI event |
| Fn-F4 always generates ACPI event |
| Fn-F5 0010 generate ACPI event enable/disable Bluetooth |
| Fn-F7 0040 generate ACPI event switch LCD and external display |
| Fn-F8 0080 generate ACPI event expand screen or none |
| Fn-F9 0100 generate ACPI event none |
| Fn-F12 always generates ACPI event |
| |
| Some models do not support all of the above. For example, the T30 does |
| not support Fn-F5 and Fn-F9. Other models do not support the mask at |
| all. On those models, hot keys cannot be controlled individually. |
| |
| Note that enabling ACPI events for some keys prevents their default |
| behavior. For example, if events for Fn-F5 are enabled, that key will |
| no longer enable/disable Bluetooth by itself. This can still be done |
| from an acpid handler for the ibm/hotkey event. |
| |
| Note also that not all Fn key combinations are supported through |
| ACPI. For example, on the X40, the brightness, volume and "Access IBM" |
| buttons do not generate ACPI events even with this driver. They *can* |
| be used through the "ThinkPad Buttons" utility, see |
| http://www.nongnu.org/tpb/ |
| |
| Bluetooth -- /proc/acpi/ibm/bluetooth |
| ------------------------------------- |
| |
| This feature shows the presence and current state of a Bluetooth |
| device. If Bluetooth is installed, the following commands can be used: |
| |
| echo enable > /proc/acpi/ibm/bluetooth |
| echo disable > /proc/acpi/ibm/bluetooth |
| |
| Video output control -- /proc/acpi/ibm/video |
| -------------------------------------------- |
| |
| This feature allows control over the devices used for video output - |
| LCD, CRT or DVI (if available). The following commands are available: |
| |
| echo lcd_enable > /proc/acpi/ibm/video |
| echo lcd_disable > /proc/acpi/ibm/video |
| echo crt_enable > /proc/acpi/ibm/video |
| echo crt_disable > /proc/acpi/ibm/video |
| echo dvi_enable > /proc/acpi/ibm/video |
| echo dvi_disable > /proc/acpi/ibm/video |
| echo auto_enable > /proc/acpi/ibm/video |
| echo auto_disable > /proc/acpi/ibm/video |
| echo expand_toggle > /proc/acpi/ibm/video |
| echo video_switch > /proc/acpi/ibm/video |
| |
| Each video output device can be enabled or disabled individually. |
| Reading /proc/acpi/ibm/video shows the status of each device. |
| |
| Automatic video switching can be enabled or disabled. When automatic |
| video switching is enabled, certain events (e.g. opening the lid, |
| docking or undocking) cause the video output device to change |
| automatically. While this can be useful, it also causes flickering |
| and, on the X40, video corruption. By disabling automatic switching, |
| the flickering or video corruption can be avoided. |
| |
| The video_switch command cycles through the available video outputs |
| (it sumulates the behavior of Fn-F7). |
| |
| Video expansion can be toggled through this feature. This controls |
| whether the display is expanded to fill the entire LCD screen when a |
| mode with less than full resolution is used. Note that the current |
| video expansion status cannot be determined through this feature. |
| |
| Note that on many models (particularly those using Radeon graphics |
| chips) the X driver configures the video card in a way which prevents |
| Fn-F7 from working. This also disables the video output switching |
| features of this driver, as it uses the same ACPI methods as |
| Fn-F7. Video switching on the console should still work. |
| |
| ThinkLight control -- /proc/acpi/ibm/light |
| ------------------------------------------ |
| |
| The current status of the ThinkLight can be found in this file. A few |
| models which do not make the status available will show it as |
| "unknown". The available commands are: |
| |
| echo on > /proc/acpi/ibm/light |
| echo off > /proc/acpi/ibm/light |
| |
| Docking / Undocking -- /proc/acpi/ibm/dock |
| ------------------------------------------ |
| |
| Docking and undocking (e.g. with the X4 UltraBase) requires some |
| actions to be taken by the operating system to safely make or break |
| the electrical connections with the dock. |
| |
| The docking feature of this driver generates the following ACPI events: |
| |
| ibm/dock GDCK 00000003 00000001 -- eject request |
| ibm/dock GDCK 00000003 00000002 -- undocked |
| ibm/dock GDCK 00000000 00000003 -- docked |
| |
| NOTE: These events will only be generated if the laptop was docked |
| when originally booted. This is due to the current lack of support for |
| hot plugging of devices in the Linux ACPI framework. If the laptop was |
| booted while not in the dock, the following message is shown in the |
| logs: "ibm_acpi: dock device not present". No dock-related events are |
| generated but the dock and undock commands described below still |
| work. They can be executed manually or triggered by Fn key |
| combinations (see the example acpid configuration files included in |
| the driver tarball package available on the web site). |
| |
| When the eject request button on the dock is pressed, the first event |
| above is generated. The handler for this event should issue the |
| following command: |
| |
| echo undock > /proc/acpi/ibm/dock |
| |
| After the LED on the dock goes off, it is safe to eject the laptop. |
| Note: if you pressed this key by mistake, go ahead and eject the |
| laptop, then dock it back in. Otherwise, the dock may not function as |
| expected. |
| |
| When the laptop is docked, the third event above is generated. The |
| handler for this event should issue the following command to fully |
| enable the dock: |
| |
| echo dock > /proc/acpi/ibm/dock |
| |
| The contents of the /proc/acpi/ibm/dock file shows the current status |
| of the dock, as provided by the ACPI framework. |
| |
| The docking support in this driver does not take care of enabling or |
| disabling any other devices you may have attached to the dock. For |
| example, a CD drive plugged into the UltraBase needs to be disabled or |
| enabled separately. See the provided example acpid configuration files |
| for how this can be accomplished. |
| |
| There is no support yet for PCI devices that may be attached to a |
| docking station, e.g. in the ThinkPad Dock II. The driver currently |
| does not recognize, enable or disable such devices. This means that |
| the only docking stations currently supported are the X-series |
| UltraBase docks and "dumb" port replicators like the Mini Dock (the |
| latter don't need any ACPI support, actually). |
| |
| UltraBay Eject -- /proc/acpi/ibm/bay |
| ------------------------------------ |
| |
| Inserting or ejecting an UltraBay device requires some actions to be |
| taken by the operating system to safely make or break the electrical |
| connections with the device. |
| |
| This feature generates the following ACPI events: |
| |
| ibm/bay MSTR 00000003 00000000 -- eject request |
| ibm/bay MSTR 00000001 00000000 -- eject lever inserted |
| |
| NOTE: These events will only be generated if the UltraBay was present |
| when the laptop was originally booted (on the X series, the UltraBay |
| is in the dock, so it may not be present if the laptop was undocked). |
| This is due to the current lack of support for hot plugging of devices |
| in the Linux ACPI framework. If the laptop was booted without the |
| UltraBay, the following message is shown in the logs: "ibm_acpi: bay |
| device not present". No bay-related events are generated but the eject |
| command described below still works. It can be executed manually or |
| triggered by a hot key combination. |
| |
| Sliding the eject lever generates the first event shown above. The |
| handler for this event should take whatever actions are necessary to |
| shut down the device in the UltraBay (e.g. call idectl), then issue |
| the following command: |
| |
| echo eject > /proc/acpi/ibm/bay |
| |
| After the LED on the UltraBay goes off, it is safe to pull out the |
| device. |
| |
| When the eject lever is inserted, the second event above is |
| generated. The handler for this event should take whatever actions are |
| necessary to enable the UltraBay device (e.g. call idectl). |
| |
| The contents of the /proc/acpi/ibm/bay file shows the current status |
| of the UltraBay, as provided by the ACPI framework. |
| |
| Experimental Features |
| --------------------- |
| |
| The following features are marked experimental because using them |
| involves guessing the correct values of some parameters. Guessing |
| incorrectly may have undesirable effects like crashing your |
| ThinkPad. USE THESE WITH CAUTION! To activate them, you'll need to |
| supply the experimental=1 parameter when loading the module. |
| |
| Experimental: CMOS control - /proc/acpi/ibm/cmos |
| ------------------------------------------------ |
| |
| This feature is used internally by the ACPI firmware to control the |
| ThinkLight on most newer ThinkPad models. It appears that it can also |
| control LCD brightness, sounds volume and more, but only on some |
| models. |
| |
| The commands are non-negative integer numbers: |
| |
| echo 0 >/proc/acpi/ibm/cmos |
| echo 1 >/proc/acpi/ibm/cmos |
| echo 2 >/proc/acpi/ibm/cmos |
| ... |
| |
| The range of numbers which are used internally by various models is 0 |
| to 21, but it's possible that numbers outside this range have |
| interesting behavior. Here is the behavior on the X40 (tpb is the |
| ThinkPad Buttons utility): |
| |
| 0 - no effect but tpb reports "Volume down" |
| 1 - no effect but tpb reports "Volume up" |
| 2 - no effect but tpb reports "Mute on" |
| 3 - simulate pressing the "Access IBM" button |
| 4 - LCD brightness up |
| 5 - LCD brightness down |
| 11 - toggle screen expansion |
| 12 - ThinkLight on |
| 13 - ThinkLight off |
| 14 - no effect but tpb reports ThinkLight status change |
| |
| If you try this feature, please send me a report similar to the |
| above. On models which allow control of LCD brightness or sound |
| volume, I'd like to provide this functionality in an user-friendly |
| way, but first I need a way to identify the models which this is |
| possible. |
| |
| Experimental: LED control - /proc/acpi/ibm/LED |
| ---------------------------------------------- |
| |
| Some of the LED indicators can be controlled through this feature. The |
| available commands are: |
| |
| echo <led number> on >/proc/acpi/ibm/led |
| echo <led number> off >/proc/acpi/ibm/led |
| echo <led number> blink >/proc/acpi/ibm/led |
| |
| The <led number> parameter is a non-negative integer. The range of LED |
| numbers used internally by various models is 0 to 7 but it's possible |
| that numbers outside this range are also valid. Here is the mapping on |
| the X40: |
| |
| 0 - power |
| 1 - battery (orange) |
| 2 - battery (green) |
| 3 - UltraBase |
| 4 - UltraBay |
| 7 - standby |
| |
| All of the above can be turned on and off and can be made to blink. |
| |
| If you try this feature, please send me a report similar to the |
| above. I'd like to provide this functionality in an user-friendly way, |
| but first I need to identify the which numbers correspond to which |
| LEDs on various models. |
| |
| Experimental: ACPI sounds - /proc/acpi/ibm/beep |
| ----------------------------------------------- |
| |
| The BEEP method is used internally by the ACPI firmware to provide |
| audible alerts in various situtation. This feature allows the same |
| sounds to be triggered manually. |
| |
| The commands are non-negative integer numbers: |
| |
| echo 0 >/proc/acpi/ibm/beep |
| echo 1 >/proc/acpi/ibm/beep |
| echo 2 >/proc/acpi/ibm/beep |
| ... |
| |
| The range of numbers which are used internally by various models is 0 |
| to 17, but it's possible that numbers outside this range are also |
| valid. Here is the behavior on the X40: |
| |
| 2 - two beeps, pause, third beep |
| 3 - single beep |
| 4 - "unable" |
| 5 - single beep |
| 6 - "AC/DC" |
| 7 - high-pitched beep |
| 9 - three short beeps |
| 10 - very long beep |
| 12 - low-pitched beep |
| |
| (I've only been able to identify a couple of them). |
| |
| If you try this feature, please send me a report similar to the |
| above. I'd like to provide this functionality in an user-friendly way, |
| but first I need to identify the which numbers correspond to which |
| sounds on various models. |
| |
| |
| Multiple Command, Module Parameters |
| ----------------------------------- |
| |
| Multiple commands can be written to the proc files in one shot by |
| separating them with commas, for example: |
| |
| echo enable,0xffff > /proc/acpi/ibm/hotkey |
| echo lcd_disable,crt_enable > /proc/acpi/ibm/video |
| |
| Commands can also be specified when loading the ibm_acpi module, for |
| example: |
| |
| modprobe ibm_acpi hotkey=enable,0xffff video=auto_disable |
| |
| |
| Example Configuration |
| --------------------- |
| |
| The ACPI support in the kernel is intended to be used in conjunction |
| with a user-space daemon, acpid. The configuration files for this |
| daemon control what actions are taken in response to various ACPI |
| events. An example set of configuration files are included in the |
| config/ directory of the tarball package available on the web |
| site. Note that these are provided for illustration purposes only and |
| may need to be adapted to your particular setup. |
| |
| The following utility scripts are used by the example action |
| scripts (included with ibm-acpi for completeness): |
| |
| /usr/local/sbin/idectl -- from the hdparm source distribution, |
| see http://www.ibiblio.org/pub/Linux/system/hardware |
| /usr/local/sbin/laptop_mode -- from the Linux kernel source |
| distribution, see Documentation/laptop-mode.txt |
| /sbin/service -- comes with Redhat/Fedora distributions |
| |
| Toan T Nguyen <ntt@control.uchicago.edu> has written a SuSE powersave |
| script for the X20, included in config/usr/sbin/ibm_hotkeys_X20 |
| |
| Henrik Brix Andersen <brix@gentoo.org> has written a Gentoo ACPI event |
| handler script for the X31. You can get the latest version from |
| http://dev.gentoo.org/~brix/files/x31.sh |
| |
| David Schweikert <dws@ee.eth.ch> has written an alternative blank.sh |
| script which works on Debian systems, included in |
| configs/etc/acpi/actions/blank-debian.sh |
| |
| |
| TODO |
| ---- |
| |
| I'd like to implement the following features but haven't yet found the |
| time and/or I don't yet know how to implement them: |
| |
| - UltraBay floppy drive support |
| |