| #ifndef _UAPI_QBT1000_H_ |
| #define _UAPI_QBT1000_H_ |
| |
| #define MAX_NAME_SIZE 32 |
| |
| /* |
| * enum qbt1000_commands - |
| * enumeration of command options |
| * @QBT1000_LOAD_APP - cmd loads TZ app |
| * @QBT1000_UNLOAD_APP - cmd unloads TZ app |
| * @QBT1000_SEND_TZCMD - sends cmd to TZ app |
| * @QBT1000_SET_FINGER_DETECT_KEY - sets the input key to send on finger detect |
| * @QBT1000_CONFIGURE_POWER_KEY - enables/disables sending the power key on |
| finger down events |
| */ |
| enum qbt1000_commands { |
| QBT1000_LOAD_APP = 100, |
| QBT1000_UNLOAD_APP = 101, |
| QBT1000_SEND_TZCMD = 102, |
| QBT1000_SET_FINGER_DETECT_KEY = 103, |
| QBT1000_CONFIGURE_POWER_KEY = 104 |
| }; |
| #define QBT1000_ENABLE_GESTURES 105 |
| |
| /* |
| * enum qbt1000_fw_event - |
| * enumeration of firmware events |
| * @FW_EVENT_FINGER_DOWN - finger down detected |
| * @FW_EVENT_FINGER_UP - finger up detected |
| * @FW_EVENT_INDICATION - an indication IPC from the firmware is pending |
| */ |
| enum qbt1000_fw_event { |
| FW_EVENT_FINGER_DOWN = 1, |
| FW_EVENT_FINGER_UP = 2, |
| FW_EVENT_CBGE_REQUIRED = 3, |
| }; |
| |
| /* |
| * struct qbt1000_app - |
| * used to load and unload apps in TZ |
| * @app_handle - qseecom handle for clients |
| * @name - Name of secure app to load |
| * @size - Size of requested buffer of secure app |
| * @high_band_width - 1 - for high bandwidth usage |
| * 0 - for normal bandwidth usage |
| */ |
| struct qbt1000_app { |
| struct qseecom_handle **app_handle; |
| char name[MAX_NAME_SIZE]; |
| uint32_t size; |
| uint8_t high_band_width; |
| }; |
| |
| /* |
| * struct qbt1000_send_tz_cmd - |
| * used to cmds to TZ App |
| * @app_handle - qseecom handle for clients |
| * @req_buf - Buffer containing request for secure app |
| * @req_buf_len - Length of request buffer |
| * @rsp_buf - Buffer containing response from secure app |
| * @rsp_buf_len - Length of response buffer |
| */ |
| struct qbt1000_send_tz_cmd { |
| struct qseecom_handle *app_handle; |
| uint8_t *req_buf; |
| uint32_t req_buf_len; |
| uint8_t *rsp_buf; |
| uint32_t rsp_buf_len; |
| }; |
| |
| /* |
| * struct qbt1000_erie_event - |
| * used to receive events from Erie |
| * @buf - Buffer containing event from Erie |
| * @buf_len - Length of buffer |
| */ |
| struct qbt1000_erie_event { |
| uint8_t *buf; |
| uint32_t buf_len; |
| }; |
| |
| /* |
| * struct qbt1000_enable_gestures - |
| * used to configure whether gestures detection is enabled or disabled |
| * @enable - if non-zero, gestures detection is enabled |
| */ |
| struct qbt1000_enable_gestures { |
| unsigned int enable; |
| }; |
| |
| /* |
| * struct qbt1000_set_finger_detect_key - |
| * used to configure the input key which is sent on finger down/up event |
| * @key_code - Key code to send on finger down/up. 0 disables sending key events |
| */ |
| struct qbt1000_set_finger_detect_key { |
| unsigned int key_code; |
| }; |
| |
| /* |
| * struct qbt1000_configure_power_key - |
| * used to configure whether the power key is sent on finger down |
| * @enable - if non-zero, power key is sent on finger down |
| */ |
| struct qbt1000_configure_power_key { |
| unsigned int enable; |
| }; |
| |
| #endif /* _UAPI_QBT1000_H_ */ |