blob: 2d5fbfd6023e8dffda80793e02c58b3f658bab0b [file] [log] [blame]
Linus Torvalds6d0b8422007-09-20 11:33:45 -07001** Introduction
2This document describes what I managed to discover about the protocol used to
3specify force effects to I-Force 2.0 devices. None of this information comes
4from Immerse. That's why you should not trust what is written in this
5document. This document is intended to help understanding the protocol.
6This is not a reference. Comments and corrections are welcome. To contact me,
Johann Deneux118e78d2007-10-20 00:47:32 +02007send an email to: johann.deneux@gmail.com
Linus Torvalds6d0b8422007-09-20 11:33:45 -07008
9** WARNING **
Matt LaPlante01dd2fb2007-10-20 01:34:40 +020010I shall not be held responsible for any damage or harm caused if you try to
Linus Torvalds6d0b8422007-09-20 11:33:45 -070011send data to your I-Force device based on what you read in this document.
12
13** Preliminary Notes:
14All values are hexadecimal with big-endian encoding (msb on the left). Beware,
15values inside packets are encoded using little-endian. Bytes whose roles are
16unknown are marked ??? Information that needs deeper inspection is marked (?)
17
18** General form of a packet **
19This is how packets look when the device uses the rs232 to communicate.
202B OP LEN DATA CS
21CS is the checksum. It is equal to the exclusive or of all bytes.
22
23When using USB:
24OP DATA
25The 2B, LEN and CS fields have disappeared, probably because USB handles frames and
26data corruption is handled or unsignificant.
27
28First, I describe effects that are sent by the device to the computer
29
30** Device input state
31This packet is used to indicate the state of each button and the value of each
32axis
33OP= 01 for a joystick, 03 for a wheel
34LEN= Varies from device to device
3500 X-Axis lsb
3601 X-Axis msb
3702 Y-Axis lsb, or gas pedal for a wheel
3803 Y-Axis msb, or brake pedal for a wheel
3904 Throttle
4005 Buttons
4106 Lower 4 bits: Buttons
42 Upper 4 bits: Hat
4307 Rudder
44
45** Device effects states
46OP= 02
47LEN= Varies
4800 ? Bit 1 (Value 2) is the value of the deadman switch
4901 Bit 8 is set if the effect is playing. Bits 0 to 7 are the effect id.
5002 ??
5103 Address of parameter block changed (lsb)
5204 Address of parameter block changed (msb)
5305 Address of second parameter block changed (lsb)
54... depending on the number of parameter blocks updated
55
56** Force effect **
57OP= 01
58LEN= 0e
5900 Channel (when playing several effects at the same time, each must be assigned a channel)
6001 Wave form
61 Val 00 Constant
62 Val 20 Square
63 Val 21 Triangle
64 Val 22 Sine
65 Val 23 Sawtooth up
66 Val 24 Sawtooth down
67 Val 40 Spring (Force = f(pos))
68 Val 41 Friction (Force = f(velocity)) and Inertia (Force = f(acceleration))
69
70
7102 Axes affected and trigger
72 Bits 4-7: Val 2 = effect along one axis. Byte 05 indicates direction
73 Val 4 = X axis only. Byte 05 must contain 5a
74 Val 8 = Y axis only. Byte 05 must contain b4
75 Val c = X and Y axes. Bytes 05 must contain 60
76 Bits 0-3: Val 0 = No trigger
77 Val x+1 = Button x triggers the effect
78 When the whole byte is 0, cancel the previously set trigger
79
8003-04 Duration of effect (little endian encoding, in ms)
81
8205 Direction of effect, if applicable. Else, see 02 for value to assign.
83
8406-07 Minimum time between triggering.
85
8608-09 Address of periodicity or magnitude parameters
870a-0b Address of attack and fade parameters, or ffff if none.
88*or*
8908-09 Address of interactive parameters for X-axis, or ffff if not applicable
900a-0b Address of interactive parameters for Y-axis, or ffff if not applicable
91
920c-0d Delay before execution of effect (little endian encoding, in ms)
93
94
95** Time based parameters **
96
97*** Attack and fade ***
98OP= 02
99LEN= 08
10000-01 Address where to store the parameteres
10102-03 Duration of attack (little endian encoding, in ms)
10204 Level at end of attack. Signed byte.
10305-06 Duration of fade.
10407 Level at end of fade.
105
106*** Magnitude ***
107OP= 03
108LEN= 03
10900-01 Address
11002 Level. Signed byte.
111
112*** Periodicity ***
113OP= 04
114LEN= 07
11500-01 Address
11602 Magnitude. Signed byte.
11703 Offset. Signed byte.
11804 Phase. Val 00 = 0 deg, Val 40 = 90 degs.
11905-06 Period (little endian encoding, in ms)
120
121** Interactive parameters **
122OP= 05
123LEN= 0a
12400-01 Address
12502 Positive Coeff
12603 Negative Coeff
12704+05 Offset (center)
12806+07 Dead band (Val 01F4 = 5000 (decimal))
12908 Positive saturation (Val 0a = 1000 (decimal) Val 64 = 10000 (decimal))
13009 Negative saturation
131
132The encoding is a bit funny here: For coeffs, these are signed values. The
133maximum value is 64 (100 decimal), the min is 9c.
134For the offset, the minimum value is FE0C, the maximum value is 01F4.
135For the deadband, the minimum value is 0, the max is 03E8.
136
137** Controls **
138OP= 41
139LEN= 03
14000 Channel
14101 Start/Stop
142 Val 00: Stop
143 Val 01: Start and play once.
144 Val 41: Start and play n times (See byte 02 below)
14502 Number of iterations n.
146
147** Init **
148
149*** Querying features ***
150OP= ff
151Query command. Length varies according to the query type.
152The general format of this packet is:
153ff 01 QUERY [INDEX] CHECKSUM
Matt LaPlante01dd2fb2007-10-20 01:34:40 +0200154responses are of the same form:
Linus Torvalds6d0b8422007-09-20 11:33:45 -0700155FF LEN QUERY VALUE_QUERIED CHECKSUM2
156where LEN = 1 + length(VALUE_QUERIED)
157
158**** Query ram size ****
159QUERY = 42 ('B'uffer size)
Matt LaPlante01dd2fb2007-10-20 01:34:40 +0200160The device should reply with the same packet plus two additional bytes
Linus Torvalds6d0b8422007-09-20 11:33:45 -0700161containing the size of the memory:
162ff 03 42 03 e8 CS would mean that the device has 1000 bytes of ram available.
163
164**** Query number of effects ****
165QUERY = 4e ('N'umber of effects)
166The device should respond by sending the number of effects that can be played
167at the same time (one byte)
168ff 02 4e 14 CS would stand for 20 effects.
169
170**** Vendor's id ****
171QUERY = 4d ('M'anufacturer)
172Query the vendors'id (2 bytes)
173
174**** Product id *****
175QUERY = 50 ('P'roduct)
176Query the product id (2 bytes)
177
178**** Open device ****
179QUERY = 4f ('O'pen)
180No data returned.
181
182**** Close device *****
183QUERY = 43 ('C')lose
184No data returned.
185
186**** Query effect ****
187QUERY = 45 ('E')
188Send effect type.
189Returns nonzero if supported (2 bytes)
190
191**** Firmware Version ****
192QUERY = 56 ('V'ersion)
193Sends back 3 bytes - major, minor, subminor
194
195*** Initialisation of the device ***
196
197**** Set Control ****
198!!! Device dependent, can be different on different models !!!
199OP= 40 <idx> <val> [<val>]
200LEN= 2 or 3
20100 Idx
202 Idx 00 Set dead zone (0..2048)
203 Idx 01 Ignore Deadman sensor (0..1)
204 Idx 02 Enable comm watchdog (0..1)
205 Idx 03 Set the strength of the spring (0..100)
206 Idx 04 Enable or disable the spring (0/1)
207 Idx 05 Set axis saturation threshold (0..2048)
208
209**** Set Effect State ****
210OP= 42 <val>
211LEN= 1
21200 State
213 Bit 3 Pause force feedback
214 Bit 2 Enable force feedback
215 Bit 0 Stop all effects
216
217**** Set overall gain ****
218OP= 43 <val>
219LEN= 1
22000 Gain
221 Val 00 = 0%
222 Val 40 = 50%
223 Val 80 = 100%
224
225** Parameter memory **
226
227Each device has a certain amount of memory to store parameters of effects.
228The amount of RAM may vary, I encountered values from 200 to 1000 bytes. Below
229is the amount of memory apparently needed for every set of parameters:
230 - period : 0c
231 - magnitude : 02
232 - attack and fade : 0e
233 - interactive : 08
234
235** Appendix: How to study the protocol ? **
236
Matt LaPlante01dd2fb2007-10-20 01:34:40 +02002371. Generate effects using the force editor provided with the DirectX SDK, or
238use Immersion Studio (freely available at their web site in the developer section:
239www.immersion.com)
2402. Start a soft spying RS232 or USB (depending on where you connected your
241joystick/wheel). I used ComPortSpy from fCoder (alpha version!)
Linus Torvalds6d0b8422007-09-20 11:33:45 -07002423. Play the effect, and watch what happens on the spy screen.
243
244A few words about ComPortSpy:
Matt LaPlante01dd2fb2007-10-20 01:34:40 +0200245At first glance, this software seems, hum, well... buggy. In fact, data appear with a
246few seconds latency. Personally, I restart it every time I play an effect.
Linus Torvalds6d0b8422007-09-20 11:33:45 -0700247Remember it's free (as in free beer) and alpha!
248
249** URLS **
250Check www.immerse.com for Immersion Studio, and www.fcoder.com for ComPortSpy.
251
252** Author of this document **
Johann Deneux118e78d2007-10-20 00:47:32 +0200253Johann Deneux <johann.deneux@gmail.com>
Justin P. Mattock0ea6e612010-07-23 20:51:24 -0700254Home page at http://web.archive.org/web/*/http://www.esil.univ-mrs.fr
Linus Torvalds6d0b8422007-09-20 11:33:45 -0700255
256Additions by Vojtech Pavlik.
257
258I-Force is trademark of Immersion Corp.