blob: 83d52c8acab0399ea82c71b259181b8e0573523f [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001
2#
3# Network device configuration
4#
5
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07006menuconfig NETDEVICES
Paolo 'Blaisorblade' Giarrussoce2d2ae2006-01-18 17:42:59 -08007 default y if UML
Jan Engelhardte0009822007-07-21 19:11:35 -07008 depends on NET
Linus Torvalds1da177e2005-04-16 15:20:36 -07009 bool "Network device support"
10 ---help---
11 You can say N here if you don't intend to connect your Linux box to
12 any other computer at all.
13
14 You'll have to say Y if your computer contains a network card that
15 you want to use under Linux. If you are going to run SLIP or PPP over
16 telephone line or null modem cable you need say Y here. Connecting
17 two machines with parallel ports using PLIP needs this, as well as
18 AX.25/KISS for sending Internet traffic over amateur radio links.
19
20 See also "The Linux Network Administrator's Guide" by Olaf Kirch and
21 Terry Dawson. Available at <http://www.tldp.org/guides.html>.
22
23 If unsure, say Y.
24
Randy Dunlap1618cb02006-09-25 23:11:21 -070025# All the following symbols are dependent on NETDEVICES - do not repeat
26# that for each of the symbols.
27if NETDEVICES
Randy Dunlapcbcd2a42005-07-27 13:04:35 -070028
Peter P Waskiewicz Jrf25f4e42007-07-06 13:36:20 -070029config NETDEVICES_MULTIQUEUE
30 bool "Netdevice multiple hardware queue support"
31 ---help---
32 Say Y here if you want to allow the network stack to use multiple
33 hardware TX queues on an ethernet device.
34
35 Most people will say N here.
36
Jamal Hadi Salim253af422006-01-08 22:34:25 -080037config IFB
38 tristate "Intermediate Functional Block support"
39 depends on NET_CLS_ACT
40 ---help---
Matt LaPlante3cb2fcc2006-11-30 05:22:59 +010041 This is an intermediate driver that allows sharing of
Jamal Hadi Salim253af422006-01-08 22:34:25 -080042 resources.
43 To compile this driver as a module, choose M here: the module
44 will be called ifb. If you want to use more than one ifb
45 device at a time, you need to compile this driver as a module.
46 Instead of 'ifb', the devices will then be called 'ifb0',
47 'ifb1' etc.
48 Look at the iproute2 documentation directory for usage etc
49
Linus Torvalds1da177e2005-04-16 15:20:36 -070050config DUMMY
51 tristate "Dummy net driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070052 ---help---
53 This is essentially a bit-bucket device (i.e. traffic you send to
54 this device is consigned into oblivion) with a configurable IP
55 address. It is most commonly used in order to make your currently
56 inactive SLIP address seem like a real address for local programs.
57 If you use SLIP or PPP, you might want to say Y here. Since this
58 thing often comes in handy, the default is Y. It won't enlarge your
59 kernel either. What a deal. Read about it in the Network
60 Administrator's Guide, available from
61 <http://www.tldp.org/docs.html#guide>.
62
63 To compile this driver as a module, choose M here: the module
64 will be called dummy. If you want to use more than one dummy
65 device at a time, you need to compile this driver as a module.
66 Instead of 'dummy', the devices will then be called 'dummy0',
67 'dummy1' etc.
68
69config BONDING
70 tristate "Bonding driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070071 depends on INET
72 ---help---
73 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
74 Channels together. This is called 'Etherchannel' by Cisco,
75 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
76
77 The driver supports multiple bonding modes to allow for both high
Jon Mason47c51432006-02-12 11:53:04 -060078 performance and high availability operation.
Linus Torvalds1da177e2005-04-16 15:20:36 -070079
80 Refer to <file:Documentation/networking/bonding.txt> for more
81 information.
82
83 To compile this driver as a module, choose M here: the module
84 will be called bonding.
85
Patrick McHardyb863ceb2007-07-14 18:55:06 -070086config MACVLAN
87 tristate "MAC-VLAN support (EXPERIMENTAL)"
88 depends on EXPERIMENTAL
89 ---help---
90 This allows one to create virtual interfaces that map packets to
91 or from specific MAC addresses to a particular interface.
92
93 To compile this driver as a module, choose M here: the module
94 will be called macvlan.
95
Linus Torvalds1da177e2005-04-16 15:20:36 -070096config EQUALIZER
97 tristate "EQL (serial line load balancing) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070098 ---help---
99 If you have two serial connections to some other computer (this
100 usually requires two modems and two telephone lines) and you use
101 SLIP (the protocol for sending Internet traffic over telephone
102 lines) or PPP (a better SLIP) on them, you can make them behave like
103 one double speed connection using this driver. Naturally, this has
104 to be supported at the other end as well, either with a similar EQL
105 Linux driver or with a Livingston Portmaster 2e.
106
107 Say Y if you want this and read
108 <file:Documentation/networking/eql.txt>. You may also want to read
109 section 6.2 of the NET-3-HOWTO, available from
110 <http://www.tldp.org/docs.html#howto>.
111
112 To compile this driver as a module, choose M here: the module
113 will be called eql. If unsure, say N.
114
115config TUN
116 tristate "Universal TUN/TAP device driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700117 select CRC32
118 ---help---
119 TUN/TAP provides packet reception and transmission for user space
120 programs. It can be viewed as a simple Point-to-Point or Ethernet
121 device, which instead of receiving packets from a physical media,
122 receives them from user space program and instead of sending packets
123 via physical media writes them to the user space program.
124
125 When a program opens /dev/net/tun, driver creates and registers
126 corresponding net device tunX or tapX. After a program closed above
127 devices, driver will automatically delete tunXX or tapXX device and
128 all routes corresponding to it.
129
130 Please read <file:Documentation/networking/tuntap.txt> for more
131 information.
132
133 To compile this driver as a module, choose M here: the module
134 will be called tun.
135
136 If you don't know what to use this for, you don't need it.
137
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700138config VETH
139 tristate "Virtual ethernet device"
140 ---help---
141 The device is an ethernet tunnel. Devices are created in pairs. When
142 one end receives the packet it appears on its pair and vice versa.
143
Linus Torvalds1da177e2005-04-16 15:20:36 -0700144config NET_SB1000
145 tristate "General Instruments Surfboard 1000"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -0700146 depends on PNP
Linus Torvalds1da177e2005-04-16 15:20:36 -0700147 ---help---
148 This is a driver for the General Instrument (also known as
149 NextLevel) SURFboard 1000 internal
150 cable modem. This is an ISA card which is used by a number of cable
151 TV companies to provide cable modem access. It's a one-way
152 downstream-only cable modem, meaning that your upstream net link is
153 provided by your regular phone modem.
154
155 At present this driver only compiles as a module, so say M here if
156 you have this card. The module will be called sb1000. Then read
157 <file:Documentation/networking/README.sb1000> for information on how
158 to use this module, as it needs special ppp scripts for establishing
159 a connection. Further documentation and the necessary scripts can be
160 found at:
161
162 <http://www.jacksonville.net/~fventuri/>
163 <http://home.adelphia.net/~siglercm/sb1000.html>
164 <http://linuxpower.cx/~cable/>
165
166 If you don't have this card, of course say N.
167
Francois Romieu1202d6f2007-09-17 17:13:55 -0700168config IP1000
169 tristate "IP1000 Gigabit Ethernet support"
170 depends on PCI && EXPERIMENTAL
171 ---help---
172 This driver supports IP1000 gigabit Ethernet cards.
173
174 To compile this driver as a module, choose M here: the module
175 will be called ipg. This is recommended.
176
Adrian Bunkf65fd8f2006-01-05 22:45:41 -0800177source "drivers/net/arcnet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700178
Andy Fleming00db8182005-07-30 19:31:23 -0400179source "drivers/net/phy/Kconfig"
180
Linus Torvalds1da177e2005-04-16 15:20:36 -0700181#
182# Ethernet
183#
184
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700185menuconfig NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -0700186 bool "Ethernet (10 or 100Mbit)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700187 depends on !UML
Linus Torvalds1da177e2005-04-16 15:20:36 -0700188 ---help---
189 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
190 type of Local Area Network (LAN) in universities and companies.
191
192 Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
193 coaxial cable, linking computers in a chain), 10BASE-T or twisted
194 pair (10 Mbps over twisted pair cable, linking computers to central
195 hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
196 100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
197 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
198 cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
199 [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
200 Ethernet (1 Gbps over optical fiber or short copper links).
201
202 If your Linux machine will be connected to an Ethernet and you have
203 an Ethernet network interface card (NIC) installed in your computer,
204 say Y here and read the Ethernet-HOWTO, available from
205 <http://www.tldp.org/docs.html#howto>. You will then also have
206 to say Y to the driver for your particular NIC.
207
208 Note that the answer to this question won't directly affect the
209 kernel: saying N will just cause the configurator to skip all
210 the questions about Ethernet network cards. If unsure, say N.
211
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700212if NET_ETHERNET
213
Linus Torvalds1da177e2005-04-16 15:20:36 -0700214config MII
215 tristate "Generic Media Independent Interface device support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700216 help
217 Most ethernet controllers have MII transceiver either as an external
218 or internal device. It is safe to say Y or M here even if your
219 ethernet card lack MII.
220
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100221config MACB
222 tristate "Atmel MACB support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700223 depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
frederic RODO6c36a702007-07-12 19:07:24 +0200224 select PHYLIB
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100225 help
226 The Atmel MACB ethernet interface is found on many AT32 and AT91
227 parts. Say Y to include support for the MACB chip.
228
229 To compile this driver as a module, choose M here: the module
230 will be called macb.
231
Linus Torvalds1da177e2005-04-16 15:20:36 -0700232source "drivers/net/arm/Kconfig"
233
Ben Dooks825a2ff2007-07-03 16:53:09 +0100234config AX88796
235 tristate "ASIX AX88796 NE2000 clone support"
Jeff Garzikdef47c52007-07-10 14:06:48 -0400236 depends on ARM || MIPS
Ben Dooks825a2ff2007-07-03 16:53:09 +0100237 select CRC32
238 select MII
239 help
240 AX88796 driver, using platform bus to provide
241 chip detection and resources
242
Magnus Damm89e536a2007-09-28 22:42:16 -0700243config AX88796_93CX6
244 bool "ASIX AX88796 external 93CX6 eeprom support"
245 depends on AX88796
246 select EEPROM_93CX6
247 help
248 Select this if your platform comes with an external 93CX6 eeprom.
249
Linus Torvalds1da177e2005-04-16 15:20:36 -0700250config MACE
251 tristate "MACE (Power Mac ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700252 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700253 select CRC32
254 help
255 Power Macintoshes and clones with Ethernet built-in on the
256 motherboard will usually use a MACE (Medium Access Control for
257 Ethernet) interface. Say Y to include support for the MACE chip.
258
259 To compile this driver as a module, choose M here: the module
260 will be called mace.
261
262config MACE_AAUI_PORT
263 bool "Use AAUI port instead of TP by default"
264 depends on MACE
265 help
266 Some Apple machines (notably the Apple Network Server) which use the
267 MACE ethernet chip have an Apple AUI port (small 15-pin connector),
268 instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say
269 Y here if you have such a machine. If unsure, say N.
270 The driver will default to AAUI on ANS anyway, and if you use it as
271 a module, you can provide the port_aaui=0|1 to force the driver.
272
273config BMAC
274 tristate "BMAC (G3 ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700275 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700276 select CRC32
277 help
278 Say Y for support of BMAC Ethernet interfaces. These are used on G3
279 computers.
280
281 To compile this driver as a module, choose M here: the module
282 will be called bmac.
283
Linus Torvalds1da177e2005-04-16 15:20:36 -0700284config ARIADNE
285 tristate "Ariadne support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700286 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700287 help
288 If you have a Village Tronic Ariadne Ethernet adapter, say Y.
289 Otherwise, say N.
290
291 To compile this driver as a module, choose M here: the module
292 will be called ariadne.
293
294config A2065
295 tristate "A2065 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700296 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700297 select CRC32
298 help
299 If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
300 say N.
301
302 To compile this driver as a module, choose M here: the module
303 will be called a2065.
304
305config HYDRA
306 tristate "Hydra support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700307 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700308 select CRC32
309 help
310 If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
311
312 To compile this driver as a module, choose M here: the module
313 will be called hydra.
314
315config ZORRO8390
316 tristate "Zorro NS8390-based Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700317 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700318 select CRC32
319 help
320 This driver is for Zorro Ethernet cards using an NS8390-compatible
321 chipset, like the Village Tronic Ariadne II and the Individual
322 Computers X-Surf Ethernet cards. If you have such a card, say Y.
323 Otherwise, say N.
324
325 To compile this driver as a module, choose M here: the module
326 will be called zorro8390.
327
328config APNE
329 tristate "PCMCIA NE2000 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700330 depends on AMIGA_PCMCIA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700331 select CRC32
332 help
333 If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
334 say N.
335
336 To compile this driver as a module, choose M here: the module
337 will be called apne.
338
339config APOLLO_ELPLUS
340 tristate "Apollo 3c505 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700341 depends on APOLLO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700342 help
343 Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
344 If you don't have one made for Apollos, you can use one from a PC,
345 except that your Apollo won't be able to boot from it (because the
346 code in the ROM will be for a PC).
347
348config MAC8390
349 bool "Macintosh NS 8390 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700350 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700351 select CRC32
352 help
353 If you want to include a driver to support Nubus or LC-PDS
354 Ethernet cards using an NS8390 chipset or its equivalent, say Y
355 and read the Ethernet-HOWTO, available from
356 <http://www.tldp.org/docs.html#howto>.
357
358config MAC89x0
359 tristate "Macintosh CS89x0 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700360 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700361 ---help---
362 Support for CS89x0 chipset based Ethernet cards. If you have a
363 Nubus or LC-PDS network (Ethernet) card of this type, say Y and
364 read the Ethernet-HOWTO, available from
365 <http://www.tldp.org/docs.html#howto>.
366
367 To compile this driver as a module, choose M here and read
368 <file:Documentation/networking/net-modules.txt>. This module will
369 be called mac89x0.
370
371config MACSONIC
372 tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700373 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700374 ---help---
375 Support for NatSemi SONIC based Ethernet devices. This includes
376 the onboard Ethernet in many Quadras as well as some LC-PDS,
377 a few Nubus and all known Comm Slot Ethernet cards. If you have
378 one of these say Y and read the Ethernet-HOWTO, available from
379 <http://www.tldp.org/docs.html#howto>.
380
381 To compile this driver as a module, choose M here and read
382 <file:Documentation/networking/net-modules.txt>. This module will
383 be called macsonic.
384
385config MACMACE
Finn Thain8b6aaab2007-05-01 22:33:01 +0200386 bool "Macintosh (AV) onboard MACE ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700387 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700388 select CRC32
389 help
390 Support for the onboard AMD 79C940 MACE Ethernet controller used in
391 the 660AV and 840AV Macintosh. If you have one of these Macintoshes
392 say Y and read the Ethernet-HOWTO, available from
393 <http://www.tldp.org/docs.html#howto>.
394
395config MVME147_NET
396 tristate "MVME147 (Lance) Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700397 depends on MVME147
Linus Torvalds1da177e2005-04-16 15:20:36 -0700398 select CRC32
399 help
400 Support for the on-board Ethernet interface on the Motorola MVME147
401 single-board computer. Say Y here to include the
402 driver for this chip in your kernel.
403 To compile this driver as a module, choose M here.
404
405config MVME16x_NET
406 tristate "MVME16x Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700407 depends on MVME16x
Linus Torvalds1da177e2005-04-16 15:20:36 -0700408 help
409 This is the driver for the Ethernet interface on the Motorola
410 MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
411 driver for this chip in your kernel.
412 To compile this driver as a module, choose M here.
413
414config BVME6000_NET
415 tristate "BVME6000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700416 depends on BVME6000
Linus Torvalds1da177e2005-04-16 15:20:36 -0700417 help
418 This is the driver for the Ethernet interface on BVME4000 and
419 BVME6000 VME boards. Say Y here to include the driver for this chip
420 in your kernel.
421 To compile this driver as a module, choose M here.
422
423config ATARILANCE
424 tristate "Atari Lance support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700425 depends on ATARI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700426 help
427 Say Y to include support for several Atari Ethernet adapters based
428 on the AMD Lance chipset: RieblCard (with or without battery), or
429 PAMCard VME (also the version by Rhotron, with different addresses).
430
Linus Torvalds1da177e2005-04-16 15:20:36 -0700431config SUN3LANCE
432 tristate "Sun3/Sun3x on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700433 depends on SUN3 || SUN3X
Linus Torvalds1da177e2005-04-16 15:20:36 -0700434 help
435 Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
436 featured an AMD Lance 10Mbit Ethernet controller on board; say Y
437 here to compile in the Linux driver for this and enable Ethernet.
438 General Linux information on the Sun 3 and 3x series (now
439 discontinued) is at
440 <http://www.angelfire.com/ca2/tech68k/sun3.html>.
441
442 If you're not building a kernel for a Sun 3, say N.
443
444config SUN3_82586
Al Viro9a482202005-08-25 06:24:56 +0100445 bool "Sun3 on-board Intel 82586 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700446 depends on SUN3
Linus Torvalds1da177e2005-04-16 15:20:36 -0700447 help
448 This driver enables support for the on-board Intel 82586 based
449 Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
450 that this driver does not support 82586-based adapters on additional
451 VME boards.
452
453config HPLANCE
454 bool "HP on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700455 depends on DIO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700456 select CRC32
457 help
458 If you want to use the builtin "LANCE" Ethernet controller on an
459 HP300 machine, say Y here.
460
461config LASI_82596
462 tristate "Lasi ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700463 depends on GSC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700464 help
Matthew Wilcox6de187e2006-11-18 10:05:16 -0700465 Say Y here to support the builtin Intel 82596 ethernet controller
466 found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700467
Thomas Bogendoerferf2ec8032007-06-28 00:49:06 +0200468config SNI_82596
469 tristate "SNI RM ethernet"
470 depends on NET_ETHERNET && SNI_RM
471 help
472 Say Y here to support the on-board Intel 82596 ethernet controller
473 built into SNI RM machines.
474
Linus Torvalds1da177e2005-04-16 15:20:36 -0700475config MIPS_JAZZ_SONIC
476 tristate "MIPS JAZZ onboard SONIC Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700477 depends on MACH_JAZZ
Linus Torvalds1da177e2005-04-16 15:20:36 -0700478 help
479 This is the driver for the onboard card of MIPS Magnum 4000,
480 Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
481
Linus Torvalds1da177e2005-04-16 15:20:36 -0700482config MIPS_AU1X00_ENET
483 bool "MIPS AU1000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700484 depends on SOC_AU1X00
Herbert Valerio Riedel0638dec2006-06-01 09:41:04 +0200485 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -0700486 select CRC32
487 help
488 If you have an Alchemy Semi AU1X00 based system
489 say Y. Otherwise, say N.
490
Linus Torvalds1da177e2005-04-16 15:20:36 -0700491config SGI_IOC3_ETH
492 bool "SGI IOC3 Ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700493 depends on PCI && SGI_IP27
Linus Torvalds1da177e2005-04-16 15:20:36 -0700494 select CRC32
495 select MII
496 help
497 If you have a network (Ethernet) card of this type, say Y and read
498 the Ethernet-HOWTO, available from
499 <http://www.tldp.org/docs.html#howto>.
500
Ralf Baechledcbf8472005-10-10 14:51:27 +0100501config MIPS_SIM_NET
Ralf Baechle1e2b9802007-03-18 23:21:22 +0000502 tristate "MIPS simulator Network device"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700503 depends on MIPS_SIM
Ralf Baechledcbf8472005-10-10 14:51:27 +0100504 help
505 The MIPSNET device is a simple Ethernet network device which is
506 emulated by the MIPS Simulator.
507 If you are not using a MIPSsim or are unsure, say N.
508
Linus Torvalds1da177e2005-04-16 15:20:36 -0700509config SGI_O2MACE_ETH
510 tristate "SGI O2 MACE Fast Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700511 depends on SGI_IP32=y
Linus Torvalds1da177e2005-04-16 15:20:36 -0700512
513config STNIC
514 tristate "National DP83902AV support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700515 depends on SUPERH
Linus Torvalds1da177e2005-04-16 15:20:36 -0700516 select CRC32
517 help
518 Support for cards based on the National Semiconductor DP83902AV
519 ST-NIC Serial Network Interface Controller for Twisted Pair. This
520 is a 10Mbit/sec Ethernet controller. Product overview and specs at
521 <http://www.national.com/pf/DP/DP83902A.html>.
522
523 If unsure, say N.
524
525config SUNLANCE
526 tristate "Sun LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700527 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700528 select CRC32
529 help
530 This driver supports the "le" interface present on all 32-bit Sparc
531 systems, on some older Ultra systems and as an Sbus option. These
532 cards are based on the AMD Lance chipset, which is better known
533 via the NE2100 cards.
534
535 To compile this driver as a module, choose M here: the module
536 will be called sunlance.
537
538config HAPPYMEAL
539 tristate "Sun Happy Meal 10/100baseT support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700540 depends on SBUS || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700541 select CRC32
542 help
543 This driver supports the "hme" interface present on most Ultra
544 systems and as an option on older Sbus systems. This driver supports
545 both PCI and Sbus devices. This driver also supports the "qfe" quad
546 100baseT device available in both PCI and Sbus configurations.
547
548 To compile this driver as a module, choose M here: the module
549 will be called sunhme.
550
551config SUNBMAC
552 tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700553 depends on SBUS && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -0700554 select CRC32
555 help
556 This driver supports the "be" interface available as an Sbus option.
557 This is Sun's older 100baseT Ethernet device.
558
559 To compile this driver as a module, choose M here: the module
560 will be called sunbmac.
561
562config SUNQE
563 tristate "Sun QuadEthernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700564 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700565 select CRC32
566 help
567 This driver supports the "qe" 10baseT Ethernet device, available as
568 an Sbus option. Note that this is not the same as Quad FastEthernet
569 "qfe" which is supported by the Happy Meal driver instead.
570
571 To compile this driver as a module, choose M here: the module
572 will be called sunqe.
573
574config SUNGEM
575 tristate "Sun GEM support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700576 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700577 select CRC32
578 help
579 Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
580 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
581
David S. Miller1f26dac2005-09-27 15:24:13 -0700582config CASSINI
583 tristate "Sun Cassini support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700584 depends on PCI
David S. Miller1f26dac2005-09-27 15:24:13 -0700585 select CRC32
586 help
587 Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
588 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
589
David S. Miller4c521e42007-07-09 22:23:51 -0700590config SUNVNET
591 tristate "Sun Virtual Network support"
592 depends on SUN_LDOMS
593 help
594 Support for virtual network devices under Sun Logical Domains.
595
Linus Torvalds1da177e2005-04-16 15:20:36 -0700596config NET_VENDOR_3COM
597 bool "3COM cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700598 depends on ISA || EISA || MCA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700599 help
600 If you have a network (Ethernet) card belonging to this class, say Y
601 and read the Ethernet-HOWTO, available from
602 <http://www.tldp.org/docs.html#howto>.
603
604 Note that the answer to this question doesn't directly affect the
605 kernel: saying N will just cause the configurator to skip all
606 the questions about 3COM cards. If you say Y, you will be asked for
607 your specific card in the following questions.
608
609config EL1
610 tristate "3c501 \"EtherLink\" support"
611 depends on NET_VENDOR_3COM && ISA
612 ---help---
613 If you have a network (Ethernet) card of this type, say Y and read
614 the Ethernet-HOWTO, available from
615 <http://www.tldp.org/docs.html#howto>. Also, consider buying a
616 new card, since the 3c501 is slow, broken, and obsolete: you will
617 have problems. Some people suggest to ping ("man ping") a nearby
618 machine every minute ("man cron") when using this card.
619
620 To compile this driver as a module, choose M here and read
621 <file:Documentation/networking/net-modules.txt>. The module
622 will be called 3c501.
623
624config EL2
625 tristate "3c503 \"EtherLink II\" support"
626 depends on NET_VENDOR_3COM && ISA
627 select CRC32
628 help
629 If you have a network (Ethernet) card of this type, say Y and read
630 the Ethernet-HOWTO, available from
631 <http://www.tldp.org/docs.html#howto>.
632
633 To compile this driver as a module, choose M here and read
634 <file:Documentation/networking/net-modules.txt>. The module
635 will be called 3c503.
636
637config ELPLUS
638 tristate "3c505 \"EtherLink Plus\" support"
Al Viroa5532602005-05-04 05:39:42 +0100639 depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700640 ---help---
641 Information about this network (Ethernet) card can be found in
642 <file:Documentation/networking/3c505.txt>. If you have a card of
643 this type, say Y and read the Ethernet-HOWTO, available from
644 <http://www.tldp.org/docs.html#howto>.
645
646 To compile this driver as a module, choose M here and read
647 <file:Documentation/networking/net-modules.txt>. The module
648 will be called 3c505.
649
650config EL16
651 tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
652 depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
653 help
654 If you have a network (Ethernet) card of this type, say Y and read
655 the Ethernet-HOWTO, available from
656 <http://www.tldp.org/docs.html#howto>.
657
658 To compile this driver as a module, choose M here and read
659 <file:Documentation/networking/net-modules.txt>. The module
660 will be called 3c507.
661
662config EL3
663 tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
664 depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
665 ---help---
666 If you have a network (Ethernet) card belonging to the 3Com
667 EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
668 from <http://www.tldp.org/docs.html#howto>.
669
670 If your card is not working you may need to use the DOS
671 setup disk to disable Plug & Play mode, and to select the default
672 media type.
673
674 To compile this driver as a module, choose M here and read
675 <file:Documentation/networking/net-modules.txt>. The module
676 will be called 3c509.
677
678config 3C515
679 tristate "3c515 ISA \"Fast EtherLink\""
Al Viroa5532602005-05-04 05:39:42 +0100680 depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700681 help
682 If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
683 network card, say Y and read the Ethernet-HOWTO, available from
684 <http://www.tldp.org/docs.html#howto>.
685
686 To compile this driver as a module, choose M here and read
687 <file:Documentation/networking/net-modules.txt>. The module
688 will be called 3c515.
689
690config ELMC
691 tristate "3c523 \"EtherLink/MC\" support"
692 depends on NET_VENDOR_3COM && MCA_LEGACY
693 help
694 If you have a network (Ethernet) card of this type, say Y and read
695 the Ethernet-HOWTO, available from
696 <http://www.tldp.org/docs.html#howto>.
697
698 To compile this driver as a module, choose M here and read
699 <file:Documentation/networking/net-modules.txt>. The module
700 will be called 3c523.
701
702config ELMC_II
703 tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
704 depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
705 help
706 If you have a network (Ethernet) card of this type, say Y and read
707 the Ethernet-HOWTO, available from
708 <http://www.tldp.org/docs.html#howto>.
709
710 To compile this driver as a module, choose M here and read
711 <file:Documentation/networking/net-modules.txt>. The module
712 will be called 3c527.
713
714config VORTEX
715 tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
716 depends on NET_VENDOR_3COM && (PCI || EISA)
717 select MII
718 ---help---
Jon Mason47c51432006-02-12 11:53:04 -0600719 This option enables driver support for a large number of 10Mbps and
720 10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
Linus Torvalds1da177e2005-04-16 15:20:36 -0700721
722 "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
723 "Boomerang" (EtherLink XL 3c900 or 3c905) PCI
724 "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus
725 "Tornado" (3c905) PCI
726 "Hurricane" (3c555/3cSOHO) PCI
727
728 If you have such a card, say Y and read the Ethernet-HOWTO,
729 available from <http://www.tldp.org/docs.html#howto>. More
730 specific information is in
731 <file:Documentation/networking/vortex.txt> and in the comments at
732 the beginning of <file:drivers/net/3c59x.c>.
733
734 To compile this support as a module, choose M here and read
735 <file:Documentation/networking/net-modules.txt>.
736
737config TYPHOON
738 tristate "3cr990 series \"Typhoon\" support"
739 depends on NET_VENDOR_3COM && PCI
740 select CRC32
741 ---help---
742 This option enables driver support for the 3cr990 series of cards:
743
744 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
745 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
746 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR
747
748 If you have a network (Ethernet) card of this type, say Y and read
749 the Ethernet-HOWTO, available from
750 <http://www.tldp.org/docs.html#howto>.
751
752 To compile this driver as a module, choose M here and read
753 <file:Documentation/networking/net-modules.txt>. The module
754 will be called typhoon.
755
756config LANCE
757 tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700758 depends on ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700759 help
760 If you have a network (Ethernet) card of this type, say Y and read
761 the Ethernet-HOWTO, available from
762 <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
763 of this type.
764
765 To compile this driver as a module, choose M here: the module
766 will be called lance. This is recommended.
767
768config NET_VENDOR_SMC
769 bool "Western Digital/SMC cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700770 depends on ISA || MCA || EISA || MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700771 help
772 If you have a network (Ethernet) card belonging to this class, say Y
773 and read the Ethernet-HOWTO, available from
774 <http://www.tldp.org/docs.html#howto>.
775
776 Note that the answer to this question doesn't directly affect the
777 kernel: saying N will just cause the configurator to skip all
778 the questions about Western Digital cards. If you say Y, you will be
779 asked for your specific card in the following questions.
780
781config WD80x3
782 tristate "WD80*3 support"
783 depends on NET_VENDOR_SMC && ISA
784 select CRC32
785 help
786 If you have a network (Ethernet) card of this type, say Y and read
787 the Ethernet-HOWTO, available from
788 <http://www.tldp.org/docs.html#howto>.
789
790 To compile this driver as a module, choose M here and read
791 <file:Documentation/networking/net-modules.txt>. The module
792 will be called wd.
793
794config ULTRAMCA
795 tristate "SMC Ultra MCA support"
796 depends on NET_VENDOR_SMC && MCA
797 select CRC32
798 help
799 If you have a network (Ethernet) card of this type and are running
800 an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
801 available from <http://www.tldp.org/docs.html#howto>.
802
803 To compile this driver as a module, choose M here and read
804 <file:Documentation/networking/net-modules.txt>. The module
805 will be called smc-mca.
806
807config ULTRA
808 tristate "SMC Ultra support"
809 depends on NET_VENDOR_SMC && ISA
810 select CRC32
811 ---help---
812 If you have a network (Ethernet) card of this type, say Y and read
813 the Ethernet-HOWTO, available from
814 <http://www.tldp.org/docs.html#howto>.
815
816 Important: There have been many reports that, with some motherboards
817 mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
818 such as some BusLogic models) causes corruption problems with many
819 operating systems. The Linux smc-ultra driver has a work-around for
820 this but keep it in mind if you have such a SCSI card and have
821 problems.
822
823 To compile this driver as a module, choose M here and read
824 <file:Documentation/networking/net-modules.txt>. The module
825 will be called smc-ultra.
826
827config ULTRA32
828 tristate "SMC Ultra32 EISA support"
829 depends on NET_VENDOR_SMC && EISA
830 select CRC32
831 help
832 If you have a network (Ethernet) card of this type, say Y and read
833 the Ethernet-HOWTO, available from
834 <http://www.tldp.org/docs.html#howto>.
835
836 To compile this driver as a module, choose M here and read
837 <file:Documentation/networking/net-modules.txt>. The module
838 will be called smc-ultra32.
839
Bryan Wue190d6b2007-07-17 14:43:44 +0800840config BFIN_MAC
841 tristate "Blackfin 536/537 on-chip mac support"
842 depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
843 select CRC32
Bryan Wueeb70af2007-09-19 23:37:41 +0800844 select MII
845 select PHYLIB
Bryan Wue190d6b2007-07-17 14:43:44 +0800846 select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
847 help
848 This is the driver for blackfin on-chip mac device. Say Y if you want it
849 compiled into the kernel. This driver is also available as a module
850 ( = code which can be inserted in and removed from the running kernel
851 whenever you want). The module will be called bfin_mac.
852
853config BFIN_MAC_USE_L1
854 bool "Use L1 memory for rx/tx packets"
855 depends on BFIN_MAC && BF537
856 default y
857 help
858 To get maximum network performace, you should use L1 memory as rx/tx buffers.
859 Say N here if you want to reserve L1 memory for other uses.
860
861config BFIN_TX_DESC_NUM
862 int "Number of transmit buffer packets"
863 depends on BFIN_MAC
864 range 6 10 if BFIN_MAC_USE_L1
865 range 10 100
866 default "10"
867 help
868 Set the number of buffer packets used in driver.
869
870config BFIN_RX_DESC_NUM
871 int "Number of receive buffer packets"
872 depends on BFIN_MAC
873 range 20 100 if BFIN_MAC_USE_L1
874 range 20 800
875 default "20"
876 help
877 Set the number of buffer packets used in driver.
878
879config BFIN_MAC_RMII
880 bool "RMII PHY Interface (EXPERIMENTAL)"
881 depends on BFIN_MAC && EXPERIMENTAL
882 default n
883 help
884 Use Reduced PHY MII Interface
885
Linus Torvalds1da177e2005-04-16 15:20:36 -0700886config SMC9194
887 tristate "SMC 9194 support"
888 depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
889 select CRC32
890 ---help---
891 This is support for the SMC9xxx based Ethernet cards. Choose this
892 option if you have a DELL laptop with the docking station, or
893 another SMC9192/9194 based chipset. Say Y if you want it compiled
894 into the kernel, and read the file
895 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
896 available from <http://www.tldp.org/docs.html#howto>.
897
898 To compile this driver as a module, choose M here and read
899 <file:Documentation/networking/net-modules.txt>. The module
900 will be called smc9194.
901
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700902config SMC91X
903 tristate "SMC 91C9x/91C1xxx support"
904 select CRC32
905 select MII
906 depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN
907 help
908 This is a driver for SMC's 91x series of Ethernet chipsets,
909 including the SMC91C94 and the SMC91C111. Say Y if you want it
910 compiled into the kernel, and read the file
911 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
912 available from <http://www.linuxdoc.org/docs.html#howto>.
913
914 This driver is also available as a module ( = code which can be
915 inserted in and removed from the running kernel whenever you want).
916 The module will be called smc91x. If you want to compile it as a
917 module, say M here and read <file:Documentation/kbuild/modules.txt>
918 as well as <file:Documentation/networking/net-modules.txt>.
919
Sascha Hauer92aa6742006-06-22 07:11:13 +0200920config NET_NETX
921 tristate "NetX Ethernet support"
922 select MII
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700923 depends on ARCH_NETX
Sascha Hauer92aa6742006-06-22 07:11:13 +0200924 help
925 This is support for the Hilscher netX builtin Ethernet ports
926
927 To compile this driver as a module, choose M here and read
928 <file:Documentation/networking/net-modules.txt>. The module
929 will be called netx-eth.
930
Sascha Hauera1365272005-05-05 15:14:15 -0700931config DM9000
932 tristate "DM9000 support"
Alex Landauf40d24d2007-07-12 12:11:48 +0800933 depends on ARM || BLACKFIN || MIPS
Sascha Hauera1365272005-05-05 15:14:15 -0700934 select CRC32
935 select MII
936 ---help---
937 Support for DM9000 chipset.
938
939 To compile this driver as a module, choose M here and read
940 <file:Documentation/networking/net-modules.txt>. The module will be
941 called dm9000.
942
Dustin McIntire0a0c72c2006-04-19 20:24:51 -0700943config SMC911X
944 tristate "SMSC LAN911[5678] support"
945 select CRC32
946 select MII
Markus Brunner726d7222007-08-20 08:36:50 +0200947 depends on ARCH_PXA || SUPERH
Dustin McIntire0a0c72c2006-04-19 20:24:51 -0700948 help
949 This is a driver for SMSC's LAN911x series of Ethernet chipsets
950 including the new LAN9115, LAN9116, LAN9117, and LAN9118.
951 Say Y if you want it compiled into the kernel,
952 and read the Ethernet-HOWTO, available from
953 <http://www.linuxdoc.org/docs.html#howto>.
954
955 This driver is also available as a module. The module will be
956 called smc911x. If you want to compile it as a module, say M
Alexander E. Patrakov39f5fb32007-03-16 18:28:43 +0500957 here and read <file:Documentation/kbuild/modules.txt>
Dustin McIntire0a0c72c2006-04-19 20:24:51 -0700958
Linus Torvalds1da177e2005-04-16 15:20:36 -0700959config NET_VENDOR_RACAL
960 bool "Racal-Interlan (Micom) NI cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700961 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700962 help
963 If you have a network (Ethernet) card belonging to this class, such
964 as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
965 available from <http://www.tldp.org/docs.html#howto>.
966
967 Note that the answer to this question doesn't directly affect the
968 kernel: saying N will just cause the configurator to skip all
969 the questions about NI cards. If you say Y, you will be asked for
970 your specific card in the following questions.
971
972config NI5010
973 tristate "NI5010 support (EXPERIMENTAL)"
974 depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
975 ---help---
976 If you have a network (Ethernet) card of this type, say Y and read
977 the Ethernet-HOWTO, available from
978 <http://www.tldp.org/docs.html#howto>. Note that this is still
979 experimental code.
980
981 To compile this driver as a module, choose M here and read
982 <file:Documentation/networking/net-modules.txt>. The module
983 will be called ni5010.
984
985config NI52
986 tristate "NI5210 support"
987 depends on NET_VENDOR_RACAL && ISA
988 help
989 If you have a network (Ethernet) card of this type, say Y and read
990 the Ethernet-HOWTO, available from
991 <http://www.tldp.org/docs.html#howto>.
992
993 To compile this driver as a module, choose M here and read
994 <file:Documentation/networking/net-modules.txt>. The module
995 will be called ni52.
996
997config NI65
998 tristate "NI6510 support"
Al Viroa5532602005-05-04 05:39:42 +0100999 depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001000 help
1001 If you have a network (Ethernet) card of this type, say Y and read
1002 the Ethernet-HOWTO, available from
1003 <http://www.tldp.org/docs.html#howto>.
1004
1005 To compile this driver as a module, choose M here and read
1006 <file:Documentation/networking/net-modules.txt>. The module
1007 will be called ni65.
1008
1009source "drivers/net/tulip/Kconfig"
1010
1011config AT1700
1012 tristate "AT1700/1720 support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001013 depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07001014 select CRC32
1015 ---help---
1016 If you have a network (Ethernet) card of this type, say Y and read
1017 the Ethernet-HOWTO, available from
1018 <http://www.tldp.org/docs.html#howto>.
1019
1020 To compile this driver as a module, choose M here and read
1021 <file:Documentation/networking/net-modules.txt>. The module
1022 will be called at1700.
1023
1024config DEPCA
1025 tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001026 depends on ISA || EISA || MCA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001027 select CRC32
1028 ---help---
1029 If you have a network (Ethernet) card of this type, say Y and read
1030 the Ethernet-HOWTO, available from
1031 <http://www.tldp.org/docs.html#howto> as well as
1032 <file:drivers/net/depca.c>.
1033
1034 To compile this driver as a module, choose M here and read
1035 <file:Documentation/networking/net-modules.txt>. The module
1036 will be called depca.
1037
1038config HP100
1039 tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001040 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001041 help
1042 If you have a network (Ethernet) card of this type, say Y and read
1043 the Ethernet-HOWTO, available from
1044 <http://www.tldp.org/docs.html#howto>.
1045
1046 To compile this driver as a module, choose M here and read
1047 <file:Documentation/networking/net-modules.txt>. The module
1048 will be called hp100.
1049
1050config NET_ISA
1051 bool "Other ISA cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001052 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001053 ---help---
1054 If your network (Ethernet) card hasn't been mentioned yet and its
1055 bus system (that's the way the cards talks to the other components
1056 of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
1057 Make sure you know the name of your card. Read the Ethernet-HOWTO,
1058 available from <http://www.tldp.org/docs.html#howto>.
1059
1060 If unsure, say Y.
1061
1062 Note that the answer to this question doesn't directly affect the
1063 kernel: saying N will just cause the configurator to skip all
1064 the remaining ISA network card questions. If you say Y, you will be
1065 asked for your specific card in the following questions.
1066
1067config E2100
1068 tristate "Cabletron E21xx support"
1069 depends on NET_ISA
1070 select CRC32
1071 help
1072 If you have a network (Ethernet) card of this type, say Y and read
1073 the Ethernet-HOWTO, available from
1074 <http://www.tldp.org/docs.html#howto>.
1075
1076 To compile this driver as a module, choose M here and read
1077 <file:Documentation/networking/net-modules.txt>. The module
1078 will be called e2100.
1079
1080config EWRK3
1081 tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
1082 depends on NET_ISA
1083 select CRC32
1084 ---help---
1085 This driver supports the DE203, DE204 and DE205 network (Ethernet)
1086 cards. If this is for you, say Y and read
1087 <file:Documentation/networking/ewrk3.txt> in the kernel source as
1088 well as the Ethernet-HOWTO, available from
1089 <http://www.tldp.org/docs.html#howto>.
1090
1091 To compile this driver as a module, choose M here and read
1092 <file:Documentation/networking/net-modules.txt>. The module
1093 will be called ewrk3.
1094
1095config EEXPRESS
1096 tristate "EtherExpress 16 support"
1097 depends on NET_ISA
1098 ---help---
1099 If you have an EtherExpress16 network (Ethernet) card, say Y and
1100 read the Ethernet-HOWTO, available from
1101 <http://www.tldp.org/docs.html#howto>. Note that the Intel
1102 EtherExpress16 card used to be regarded as a very poor choice
1103 because the driver was very unreliable. We now have a new driver
1104 that should do better.
1105
1106 To compile this driver as a module, choose M here and read
1107 <file:Documentation/networking/net-modules.txt>. The module
1108 will be called eexpress.
1109
1110config EEXPRESS_PRO
1111 tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
1112 depends on NET_ISA
1113 ---help---
1114 If you have a network (Ethernet) card of this type, say Y. This
Jon Mason47c51432006-02-12 11:53:04 -06001115 driver supports Intel i82595{FX,TX} based boards. Note however
Linus Torvalds1da177e2005-04-16 15:20:36 -07001116 that the EtherExpress PRO/100 Ethernet card has its own separate
1117 driver. Please read the Ethernet-HOWTO, available from
1118 <http://www.tldp.org/docs.html#howto>.
1119
1120 To compile this driver as a module, choose M here and read
1121 <file:Documentation/networking/net-modules.txt>. The module
1122 will be called eepro.
1123
Linus Torvalds1da177e2005-04-16 15:20:36 -07001124config HPLAN_PLUS
1125 tristate "HP PCLAN+ (27247B and 27252A) support"
1126 depends on NET_ISA
1127 select CRC32
1128 help
1129 If you have a network (Ethernet) card of this type, say Y and read
1130 the Ethernet-HOWTO, available from
1131 <http://www.tldp.org/docs.html#howto>.
1132
1133 To compile this driver as a module, choose M here and read
1134 <file:Documentation/networking/net-modules.txt>. The module
1135 will be called hp-plus.
1136
1137config HPLAN
1138 tristate "HP PCLAN (27245 and other 27xxx series) support"
1139 depends on NET_ISA
1140 select CRC32
1141 help
1142 If you have a network (Ethernet) card of this type, say Y and read
1143 the Ethernet-HOWTO, available from
1144 <http://www.tldp.org/docs.html#howto>.
1145
1146 To compile this driver as a module, choose M here and read
1147 <file:Documentation/networking/net-modules.txt>. The module
1148 will be called hp.
1149
1150config LP486E
1151 tristate "LP486E on board Ethernet"
1152 depends on NET_ISA
1153 help
1154 Say Y here to support the 82596-based on-board Ethernet controller
1155 for the Panther motherboard, which is one of the two shipped in the
1156 Intel Professional Workstation.
1157
1158config ETH16I
1159 tristate "ICL EtherTeam 16i/32 support"
1160 depends on NET_ISA
1161 help
1162 If you have a network (Ethernet) card of this type, say Y and read
1163 the Ethernet-HOWTO, available from
1164 <http://www.tldp.org/docs.html#howto>.
1165
1166 To compile this driver as a module, choose M here and read
1167 <file:Documentation/networking/net-modules.txt>. The module
1168 will be called eth16i.
1169
1170config NE2000
1171 tristate "NE2000/NE1000 support"
Atsushi Nemoto57e386c2007-05-01 00:27:58 +09001172 depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938
Linus Torvalds1da177e2005-04-16 15:20:36 -07001173 select CRC32
1174 ---help---
1175 If you have a network (Ethernet) card of this type, say Y and read
1176 the Ethernet-HOWTO, available from
1177 <http://www.tldp.org/docs.html#howto>. Many Ethernet cards
1178 without a specific driver are compatible with NE2000.
1179
1180 If you have a PCI NE2000 card however, say N here and Y to "PCI
Jesper Juhl28beaf62006-03-08 00:06:31 -08001181 NE2000 and clone support" under "EISA, VLB, PCI and on board
1182 controllers" below. If you have a NE2000 card and are running on
Linus Torvalds1da177e2005-04-16 15:20:36 -07001183 an MCA system (a bus system used on some IBM PS/2 computers and
1184 laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
1185 below.
1186
1187 To compile this driver as a module, choose M here and read
1188 <file:Documentation/networking/net-modules.txt>. The module
1189 will be called ne.
1190
1191config ZNET
1192 tristate "Zenith Z-Note support (EXPERIMENTAL)"
Al Viroa5532602005-05-04 05:39:42 +01001193 depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001194 help
1195 The Zenith Z-Note notebook computer has a built-in network
1196 (Ethernet) card, and this is the Linux driver for it. Note that the
1197 IBM Thinkpad 300 is compatible with the Z-Note and is also supported
1198 by this driver. Read the Ethernet-HOWTO, available from
1199 <http://www.tldp.org/docs.html#howto>.
1200
1201config SEEQ8005
1202 tristate "SEEQ8005 support (EXPERIMENTAL)"
1203 depends on NET_ISA && EXPERIMENTAL
1204 help
1205 This is a driver for the SEEQ 8005 network (Ethernet) card. If this
1206 is for you, read the Ethernet-HOWTO, available from
1207 <http://www.tldp.org/docs.html#howto>.
1208
1209 To compile this driver as a module, choose M here and read
1210 <file:Documentation/networking/net-modules.txt>. The module
1211 will be called seeq8005.
1212
Linus Torvalds1da177e2005-04-16 15:20:36 -07001213config NE2_MCA
1214 tristate "NE/2 (ne2000 MCA version) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001215 depends on MCA_LEGACY
Linus Torvalds1da177e2005-04-16 15:20:36 -07001216 select CRC32
1217 help
1218 If you have a network (Ethernet) card of this type, say Y and read
1219 the Ethernet-HOWTO, available from
1220 <http://www.tldp.org/docs.html#howto>.
1221
1222 To compile this driver as a module, choose M here and read
1223 <file:Documentation/networking/net-modules.txt>. The module
1224 will be called ne2.
1225
1226config IBMLANA
1227 tristate "IBM LAN Adapter/A support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001228 depends on MCA && MCA_LEGACY
Linus Torvalds1da177e2005-04-16 15:20:36 -07001229 ---help---
1230 This is a Micro Channel Ethernet adapter. You need to set
1231 CONFIG_MCA to use this driver. It is both available as an in-kernel
1232 driver and as a module.
1233
1234 To compile this driver as a module, choose M here and read
1235 <file:Documentation/networking/net-modules.txt>. The only
1236 currently supported card is the IBM LAN Adapter/A for Ethernet. It
1237 will both support 16K and 32K memory windows, however a 32K window
1238 gives a better security against packet losses. Usage of multiple
1239 boards with this driver should be possible, but has not been tested
1240 up to now due to lack of hardware.
1241
1242config IBMVETH
1243 tristate "IBM LAN Virtual Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001244 depends on PPC_PSERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07001245 ---help---
1246 This driver supports virtual ethernet adapters on newer IBM iSeries
1247 and pSeries systems.
1248
1249 To compile this driver as a module, choose M here and read
1250 <file:Documentation/networking/net-modules.txt>. The module will
1251 be called ibmveth.
1252
David Gibson1d3bb992007-08-23 13:56:01 +10001253source "drivers/net/ibm_emac/Kconfig"
1254source "drivers/net/ibm_newemac/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001255
1256config NET_PCI
1257 bool "EISA, VLB, PCI and on board controllers"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001258 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001259 help
1260 This is another class of network cards which attach directly to the
1261 bus. If you have one of those, say Y and read the Ethernet-HOWTO,
1262 available from <http://www.tldp.org/docs.html#howto>.
1263
1264 Note that the answer to this question doesn't directly affect the
1265 kernel: saying N will just cause the configurator to skip all
1266 the questions about this class of network cards. If you say Y, you
1267 will be asked for your specific card in the following questions. If
1268 you are unsure, say Y.
1269
1270config PCNET32
1271 tristate "AMD PCnet32 PCI support"
1272 depends on NET_PCI && PCI
1273 select CRC32
1274 select MII
1275 help
1276 If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
1277 answer Y here and read the Ethernet-HOWTO, available from
1278 <http://www.tldp.org/docs.html#howto>.
1279
1280 To compile this driver as a module, choose M here and read
1281 <file:Documentation/networking/net-modules.txt>. The module
1282 will be called pcnet32.
1283
Don Fry7de745e2006-09-13 10:16:53 -07001284config PCNET32_NAPI
pcnet32@verizon.net659dd832007-02-16 10:09:57 -06001285 bool "Use RX polling (NAPI)"
1286 depends on PCNET32
Don Fry7de745e2006-09-13 10:16:53 -07001287 help
1288 NAPI is a new driver API designed to reduce CPU and interrupt load
1289 when the driver is receiving lots of packets from the card. It is
1290 still somewhat experimental and thus not yet enabled by default.
1291
1292 If your estimated Rx load is 10kpps or more, or if the card will be
1293 deployed on potentially unfriendly networks (e.g. in a firewall),
1294 then say Y here.
1295
1296 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
1297 information.
1298
1299 If in doubt, say N.
1300
Linus Torvalds1da177e2005-04-16 15:20:36 -07001301config AMD8111_ETH
1302 tristate "AMD 8111 (new PCI lance) support"
1303 depends on NET_PCI && PCI
1304 select CRC32
1305 select MII
1306 help
1307 If you have an AMD 8111-based PCI lance ethernet card,
1308 answer Y here and read the Ethernet-HOWTO, available from
1309 <http://www.tldp.org/docs.html#howto>.
1310
1311 To compile this driver as a module, choose M here and read
1312 <file:Documentation/networking/net-modules.txt>. The module
1313 will be called amd8111e.
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001314
Linus Torvalds1da177e2005-04-16 15:20:36 -07001315config AMD8111E_NAPI
1316 bool "Enable NAPI support"
1317 depends on AMD8111_ETH
1318 help
1319 NAPI is a new driver API designed to reduce CPU and interrupt load
1320 when the driver is receiving lots of packets from the card. It is
1321 still somewhat experimental and thus not yet enabled by default.
1322
1323 If your estimated Rx load is 10kpps or more, or if the card will be
1324 deployed on potentially unfriendly networks (e.g. in a firewall),
1325 then say Y here.
1326
1327 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
1328 information.
1329
1330 If in doubt, say N.
1331
1332config ADAPTEC_STARFIRE
1333 tristate "Adaptec Starfire/DuraLAN support"
1334 depends on NET_PCI && PCI
1335 select CRC32
1336 select MII
1337 help
1338 Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
1339 adapter. The DuraLAN chip is used on the 64 bit PCI boards from
1340 Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
1341 driver.
1342
1343 To compile this driver as a module, choose M here: the module
1344 will be called starfire. This is recommended.
1345
1346config ADAPTEC_STARFIRE_NAPI
1347 bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
1348 depends on ADAPTEC_STARFIRE && EXPERIMENTAL
1349 help
1350 NAPI is a new driver API designed to reduce CPU and interrupt load
1351 when the driver is receiving lots of packets from the card. It is
1352 still somewhat experimental and thus not yet enabled by default.
1353
1354 If your estimated Rx load is 10kpps or more, or if the card will be
1355 deployed on potentially unfriendly networks (e.g. in a firewall),
1356 then say Y here.
1357
1358 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
1359 information.
1360
1361 If in doubt, say N.
1362
1363config AC3200
1364 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
1365 depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
1366 select CRC32
1367 help
1368 If you have a network (Ethernet) card of this type, say Y and read
1369 the Ethernet-HOWTO, available from
1370 <http://www.tldp.org/docs.html#howto>.
1371
1372 To compile this driver as a module, choose M here and read
1373 <file:Documentation/networking/net-modules.txt>. The module
1374 will be called ac3200.
1375
1376config APRICOT
1377 tristate "Apricot Xen-II on board Ethernet"
1378 depends on NET_PCI && ISA
1379 help
1380 If you have a network (Ethernet) controller of this type, say Y and
1381 read the Ethernet-HOWTO, available from
1382 <http://www.tldp.org/docs.html#howto>.
1383
1384 To compile this driver as a module, choose M here and read
1385 <file:Documentation/networking/net-modules.txt>. The module will be
1386 called apricot.
1387
1388config B44
Michael Buesch753f4922007-09-19 14:20:30 -07001389 tristate "Broadcom 440x/47xx ethernet support"
1390 depends on SSB_POSSIBLE
1391 select SSB
Linus Torvalds1da177e2005-04-16 15:20:36 -07001392 select MII
1393 help
Michael Buesch753f4922007-09-19 14:20:30 -07001394 If you have a network (Ethernet) controller of this type, say Y
1395 or M and read the Ethernet-HOWTO, available from
Linus Torvalds1da177e2005-04-16 15:20:36 -07001396 <http://www.tldp.org/docs.html#howto>.
1397
1398 To compile this driver as a module, choose M here and read
1399 <file:Documentation/networking/net-modules.txt>. The module will be
1400 called b44.
1401
Michael Buesch753f4922007-09-19 14:20:30 -07001402# Auto-select SSB PCI-HOST support, if possible
1403config B44_PCI_AUTOSELECT
1404 bool
1405 depends on B44 && SSB_PCIHOST_POSSIBLE
1406 select SSB_PCIHOST
1407 default y
1408
1409# Auto-select SSB PCICORE driver, if possible
1410config B44_PCICORE_AUTOSELECT
1411 bool
1412 depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
1413 select SSB_DRIVER_PCICORE
1414 default y
1415
1416config B44_PCI
1417 bool
1418 depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
1419 default y
1420
Linus Torvalds1da177e2005-04-16 15:20:36 -07001421config FORCEDETH
Adrian Bunk82770082006-03-08 00:06:30 -08001422 tristate "nForce Ethernet support"
1423 depends on NET_PCI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001424 help
1425 If you have a network (Ethernet) controller of this type, say Y and
1426 read the Ethernet-HOWTO, available from
1427 <http://www.tldp.org/docs.html#howto>.
1428
1429 To compile this driver as a module, choose M here and read
1430 <file:Documentation/networking/net-modules.txt>. The module will be
1431 called forcedeth.
1432
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001433config FORCEDETH_NAPI
1434 bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
1435 depends on FORCEDETH && EXPERIMENTAL
1436 help
1437 NAPI is a new driver API designed to reduce CPU and interrupt load
1438 when the driver is receiving lots of packets from the card. It is
1439 still somewhat experimental and thus not yet enabled by default.
1440
1441 If your estimated Rx load is 10kpps or more, or if the card will be
1442 deployed on potentially unfriendly networks (e.g. in a firewall),
1443 then say Y here.
1444
1445 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
1446 information.
1447
1448 If in doubt, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001449
1450config CS89x0
1451 tristate "CS89x0 support"
Deepak Saxena9c878962006-01-14 13:21:18 -08001452 depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001453 ---help---
1454 Support for CS89x0 chipset based Ethernet cards. If you have a
1455 network (Ethernet) card of this type, say Y and read the
1456 Ethernet-HOWTO, available from
1457 <http://www.tldp.org/docs.html#howto> as well as
1458 <file:Documentation/networking/cs89x0.txt>.
1459
1460 To compile this driver as a module, choose M here and read
1461 <file:Documentation/networking/net-modules.txt>. The module will be
Jean Delvarefd85d762006-01-11 12:17:36 -08001462 called cs89x0.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001463
1464config TC35815
1465 tristate "TOSHIBA TC35815 Ethernet support"
Atsushi Nemotoeea221ce2007-03-03 23:54:59 +09001466 depends on NET_PCI && PCI && MIPS
1467 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07001468
Linus Torvalds1da177e2005-04-16 15:20:36 -07001469config EEPRO100
1470 tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
1471 depends on NET_PCI && PCI
1472 select MII
1473 help
1474 If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
1475 card, say Y and read the Ethernet-HOWTO, available from
1476 <http://www.tldp.org/docs.html#howto>.
1477
1478 To compile this driver as a module, choose M here and read
1479 <file:Documentation/networking/net-modules.txt>. The module
1480 will be called eepro100.
1481
1482
1483config E100
1484 tristate "Intel(R) PRO/100+ support"
1485 depends on NET_PCI && PCI
1486 select MII
1487 ---help---
1488 This driver supports Intel(R) PRO/100 family of adapters.
1489 To verify that your adapter is supported, find the board ID number
1490 on the adapter. Look for a label that has a barcode and a number
1491 in the format 123456-001 (six digits hyphen three digits).
1492
1493 Use the above information and the Adapter & Driver ID Guide at:
1494
1495 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
1496
1497 to identify the adapter.
1498
1499 For the latest Intel PRO/100 network driver for Linux, see:
1500
1501 <http://appsr.intel.com/scripts-df/support_intel.asp>
1502
1503 More specific information on configuring the driver is in
1504 <file:Documentation/networking/e100.txt>.
1505
1506 To compile this driver as a module, choose M here and read
1507 <file:Documentation/networking/net-modules.txt>. The module
1508 will be called e100.
1509
1510config LNE390
1511 tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
1512 depends on NET_PCI && EISA && EXPERIMENTAL
1513 select CRC32
1514 help
1515 If you have a network (Ethernet) card of this type, say Y and read
1516 the Ethernet-HOWTO, available from
1517 <http://www.tldp.org/docs.html#howto>.
1518
1519 To compile this driver as a module, choose M here and read
1520 <file:Documentation/networking/net-modules.txt>. The module
1521 will be called lne390.
1522
1523config FEALNX
1524 tristate "Myson MTD-8xx PCI Ethernet support"
1525 depends on NET_PCI && PCI
1526 select CRC32
1527 select MII
1528 help
1529 Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
1530 cards. Specifications and data at
1531 <http://www.myson.com.hk/mtd/datasheet/>.
1532
1533config NATSEMI
1534 tristate "National Semiconductor DP8381x series PCI Ethernet support"
1535 depends on NET_PCI && PCI
1536 select CRC32
1537 help
1538 This driver is for the National Semiconductor DP83810 series,
1539 which is used in cards from PureData, NetGear, Linksys
1540 and others, including the 83815 chip.
1541 More specific information and updates are available from
1542 <http://www.scyld.com/network/natsemi.html>.
1543
1544config NE2K_PCI
1545 tristate "PCI NE2000 and clones support (see help)"
1546 depends on NET_PCI && PCI
1547 select CRC32
1548 ---help---
1549 This driver is for NE2000 compatible PCI cards. It will not work
1550 with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
1551 support" below). If you have a PCI NE2000 network (Ethernet) card,
1552 say Y and read the Ethernet-HOWTO, available from
1553 <http://www.tldp.org/docs.html#howto>.
1554
1555 This driver also works for the following NE2000 clone cards:
1556 RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2
1557 NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
1558 Holtek HT80232 Holtek HT80229
1559
1560 To compile this driver as a module, choose M here and read
1561 <file:Documentation/networking/net-modules.txt>. The module
1562 will be called ne2k-pci.
1563
1564config NE3210
1565 tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
1566 depends on NET_PCI && EISA && EXPERIMENTAL
1567 select CRC32
1568 ---help---
1569 If you have a network (Ethernet) card of this type, say Y and read
1570 the Ethernet-HOWTO, available from
1571 <http://www.tldp.org/docs.html#howto>. Note that this driver
1572 will NOT WORK for NE3200 cards as they are completely different.
1573
1574 To compile this driver as a module, choose M here and read
1575 <file:Documentation/networking/net-modules.txt>. The module
1576 will be called ne3210.
1577
1578config ES3210
1579 tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
1580 depends on NET_PCI && EISA && EXPERIMENTAL
1581 select CRC32
1582 help
1583 If you have a network (Ethernet) card of this type, say Y and read
1584 the Ethernet-HOWTO, available from
1585 <http://www.tldp.org/docs.html#howto>.
1586
1587 To compile this driver as a module, choose M here and read
1588 <file:Documentation/networking/net-modules.txt>. The module
1589 will be called es3210.
1590
1591config 8139CP
1592 tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
1593 depends on NET_PCI && PCI && EXPERIMENTAL
1594 select CRC32
1595 select MII
1596 help
1597 This is a driver for the Fast Ethernet PCI network cards based on
1598 the RTL8139C+ chips. If you have one of those, say Y and read
1599 the Ethernet-HOWTO, available from
1600 <http://www.tldp.org/docs.html#howto>.
1601
1602 To compile this driver as a module, choose M here: the module
1603 will be called 8139cp. This is recommended.
1604
1605config 8139TOO
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001606 tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001607 depends on NET_PCI && PCI
1608 select CRC32
1609 select MII
1610 ---help---
1611 This is a driver for the Fast Ethernet PCI network cards based on
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001612 the RTL 8129/8130/8139 chips. If you have one of those, say Y and
1613 read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001614
1615 To compile this driver as a module, choose M here: the module
1616 will be called 8139too. This is recommended.
1617
1618config 8139TOO_PIO
1619 bool "Use PIO instead of MMIO"
1620 default y
1621 depends on 8139TOO
1622 help
1623 This instructs the driver to use programmed I/O ports (PIO) instead
1624 of PCI shared memory (MMIO). This can possibly solve some problems
1625 in case your mainboard has memory consistency issues. If unsure,
1626 say N.
1627
1628config 8139TOO_TUNE_TWISTER
1629 bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
1630 depends on 8139TOO
1631 help
1632 This implements a function which might come in handy in case you
1633 are using low quality on long cabling. It is required for RealTek
1634 RTL-8139 revision K boards, and totally unused otherwise. It tries
1635 to match the transceiver to the cable characteristics. This is
1636 experimental since hardly documented by the manufacturer.
1637 If unsure, say Y.
1638
1639config 8139TOO_8129
1640 bool "Support for older RTL-8129/8130 boards"
1641 depends on 8139TOO
1642 help
1643 This enables support for the older and uncommon RTL-8129 and
1644 RTL-8130 chips, which support MII via an external transceiver,
1645 instead of an internal one. Disabling this option will save some
1646 memory by making the code size smaller. If unsure, say Y.
1647
1648config 8139_OLD_RX_RESET
1649 bool "Use older RX-reset method"
1650 depends on 8139TOO
1651 help
1652 The 8139too driver was recently updated to contain a more rapid
1653 reset sequence, in the face of severe receive errors. This "new"
1654 RX-reset method should be adequate for all boards. But if you
1655 experience problems, you can enable this option to restore the
1656 old RX-reset behavior. If unsure, say N.
1657
1658config SIS900
1659 tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
1660 depends on NET_PCI && PCI
1661 select CRC32
Adrian Bunk6da0f682005-04-30 13:52:49 +02001662 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07001663 ---help---
1664 This is a driver for the Fast Ethernet PCI network cards based on
1665 the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
Adrian Bunkc3cf5602006-03-04 17:07:57 +01001666 SiS 630 and SiS 540 chipsets.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001667
1668 This driver also supports AMD 79C901 HomePNA so that you can use
1669 your phone line as a network cable.
1670
1671 To compile this driver as a module, choose M here: the module
1672 will be called sis900. This is recommended.
1673
1674config EPIC100
1675 tristate "SMC EtherPower II"
1676 depends on NET_PCI && PCI
1677 select CRC32
1678 select MII
1679 help
1680 This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
1681 which is based on the SMC83c17x (EPIC/100).
1682 More specific information and updates are available from
1683 <http://www.scyld.com/network/epic100.html>.
1684
1685config SUNDANCE
1686 tristate "Sundance Alta support"
1687 depends on NET_PCI && PCI
1688 select CRC32
1689 select MII
1690 help
1691 This driver is for the Sundance "Alta" chip.
1692 More specific information and updates are available from
1693 <http://www.scyld.com/network/sundance.html>.
1694
1695config SUNDANCE_MMIO
1696 bool "Use MMIO instead of PIO"
1697 depends on SUNDANCE
1698 help
1699 Enable memory-mapped I/O for interaction with Sundance NIC registers.
1700 Do NOT enable this by default, PIO (enabled when MMIO is disabled)
1701 is known to solve bugs on certain chips.
1702
1703 If unsure, say N.
1704
1705config TLAN
1706 tristate "TI ThunderLAN support"
1707 depends on NET_PCI && (PCI || EISA) && !64BIT
1708 ---help---
1709 If you have a PCI Ethernet network card based on the ThunderLAN chip
1710 which is supported by this driver, say Y and read the
1711 Ethernet-HOWTO, available from
1712 <http://www.tldp.org/docs.html#howto>.
1713
1714 Devices currently supported by this driver are Compaq Netelligent,
1715 Compaq NetFlex and Olicom cards. Please read the file
1716 <file:Documentation/networking/tlan.txt> for more details.
1717
1718 To compile this driver as a module, choose M here and read
1719 <file:Documentation/networking/net-modules.txt>. The module
1720 will be called tlan.
1721
1722 Please email feedback to <torben.mathiasen@compaq.com>.
1723
1724config VIA_RHINE
1725 tristate "VIA Rhine support"
1726 depends on NET_PCI && PCI
1727 select CRC32
1728 select MII
1729 help
1730 If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
1731 Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
1732 Ethernet functions can also be found integrated on South Bridges
1733 (e.g. VT8235).
1734
1735 To compile this driver as a module, choose M here. The module
1736 will be called via-rhine.
1737
1738config VIA_RHINE_MMIO
1739 bool "Use MMIO instead of PIO"
1740 depends on VIA_RHINE
1741 help
1742 This instructs the driver to use PCI shared memory (MMIO) instead of
1743 programmed I/O ports (PIO). Enabling this gives an improvement in
1744 processing time in parts of the driver.
1745
1746 If unsure, say Y.
1747
Roger Luethi633949a2006-08-14 23:00:17 -07001748config VIA_RHINE_NAPI
1749 bool "Use Rx Polling (NAPI)"
1750 depends on VIA_RHINE
1751 help
1752 NAPI is a new driver API designed to reduce CPU and interrupt load
1753 when the driver is receiving lots of packets from the card.
1754
1755 If your estimated Rx load is 10kpps or more, or if the card will be
1756 deployed on potentially unfriendly networks (e.g. in a firewall),
1757 then say Y here.
1758
1759 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
1760 information.
1761
Linus Torvalds1da177e2005-04-16 15:20:36 -07001762config LAN_SAA9730
Ralf Baechlef2b67c72006-11-29 17:10:38 +00001763 bool "Philips SAA9730 Ethernet support"
1764 depends on NET_PCI && PCI && MIPS_ATLAS
Linus Torvalds1da177e2005-04-16 15:20:36 -07001765 help
1766 The SAA9730 is a combined multimedia and peripheral controller used
1767 in thin clients, Internet access terminals, and diskless
1768 workstations.
1769 See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
1770
Cesar Eduardo Barrosbf345702006-12-19 13:08:47 -08001771config SC92031
1772 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
1773 depends on NET_PCI && PCI && EXPERIMENTAL
1774 select CRC32
1775 ---help---
1776 This is a driver for the Fast Ethernet PCI network cards based on
1777 the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
1778 have one of these, say Y here.
1779
1780 To compile this driver as a module, choose M here: the module
1781 will be called sc92031. This is recommended.
1782
Matteo Croced95b39c2007-10-14 18:10:13 +02001783config CPMAC
1784 tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
1785 depends on NET_ETHERNET && EXPERIMENTAL && AR7
1786 select PHYLIB
1787 select FIXED_PHY
1788 select FIXED_MII_100_FDX
1789 help
1790 TI AR7 CPMAC Ethernet support
1791
Linus Torvalds1da177e2005-04-16 15:20:36 -07001792config NET_POCKET
1793 bool "Pocket and portable adapters"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001794 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001795 ---help---
1796 Cute little network (Ethernet) devices which attach to the parallel
1797 port ("pocket adapters"), commonly used with laptops. If you have
1798 one of those, say Y and read the Ethernet-HOWTO, available from
1799 <http://www.tldp.org/docs.html#howto>.
1800
1801 If you want to plug a network (or some other) card into the PCMCIA
1802 (or PC-card) slot of your laptop instead (PCMCIA is the standard for
1803 credit card size extension cards used by all modern laptops), you
1804 need the pcmcia-cs package (location contained in the file
1805 <file:Documentation/Changes>) and you can say N here.
1806
1807 Laptop users should read the Linux Laptop home page at
1808 <http://www.linux-on-laptops.com/> or
1809 Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.
1810
1811 Note that the answer to this question doesn't directly affect the
1812 kernel: saying N will just cause the configurator to skip all
1813 the questions about this class of network devices. If you say Y, you
1814 will be asked for your specific device in the following questions.
1815
1816config ATP
1817 tristate "AT-LAN-TEC/RealTek pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001818 depends on NET_POCKET && PARPORT && X86
Linus Torvalds1da177e2005-04-16 15:20:36 -07001819 select CRC32
1820 ---help---
1821 This is a network (Ethernet) device which attaches to your parallel
1822 port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
1823 available from <http://www.tldp.org/docs.html#howto>, if you
1824 want to use this. If you intend to use this driver, you should have
1825 said N to the "Parallel printer support", because the two drivers
1826 don't like each other.
1827
1828 To compile this driver as a module, choose M here: the module
1829 will be called atp.
1830
1831config DE600
1832 tristate "D-Link DE600 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001833 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001834 ---help---
1835 This is a network (Ethernet) device which attaches to your parallel
1836 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1837 Ethernet-HOWTO, available from
1838 <http://www.tldp.org/docs.html#howto>, if you want to use
1839 this. It is possible to have several devices share a single parallel
1840 port and it is safe to compile the corresponding drivers into the
1841 kernel.
1842
1843 To compile this driver as a module, choose M here: the module
1844 will be called de600.
1845
1846config DE620
1847 tristate "D-Link DE620 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001848 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001849 ---help---
1850 This is a network (Ethernet) device which attaches to your parallel
1851 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1852 Ethernet-HOWTO, available from
1853 <http://www.tldp.org/docs.html#howto>, if you want to use
1854 this. It is possible to have several devices share a single parallel
1855 port and it is safe to compile the corresponding drivers into the
1856 kernel.
1857
1858 To compile this driver as a module, choose M here: the module
1859 will be called de620.
1860
1861config SGISEEQ
1862 tristate "SGI Seeq ethernet controller support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001863 depends on SGI_IP22
Linus Torvalds1da177e2005-04-16 15:20:36 -07001864 help
1865 Say Y here if you have an Seeq based Ethernet network card. This is
1866 used in many Silicon Graphics machines.
1867
1868config DECLANCE
1869 tristate "DEC LANCE ethernet controller support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001870 depends on MACH_DECSTATION
Linus Torvalds1da177e2005-04-16 15:20:36 -07001871 select CRC32
1872 help
1873 This driver is for the series of Ethernet controllers produced by
1874 DEC (now Compaq) based on the AMD Lance chipset, including the
1875 DEPCA series. (This chipset is better known via the NE2100 cards.)
1876
1877config 68360_ENET
1878 bool "Motorola 68360 ethernet controller"
1879 depends on M68360
1880 help
1881 Say Y here if you want to use the built-in ethernet controller of
1882 the Motorola 68360 processor.
1883
1884config FEC
Greg Ungerer2af69212005-09-12 11:18:10 +10001885 bool "FEC ethernet controller (of ColdFire CPUs)"
Greg Ungerer892b6252006-01-10 16:58:16 +10001886 depends on M523x || M527x || M5272 || M528x || M520x
Linus Torvalds1da177e2005-04-16 15:20:36 -07001887 help
1888 Say Y here if you want to use the built-in 10/100 Fast ethernet
Greg Ungerer2af69212005-09-12 11:18:10 +10001889 controller on some Motorola ColdFire processors.
1890
1891config FEC2
1892 bool "Second FEC ethernet controller (on some ColdFire CPUs)"
1893 depends on FEC
1894 help
1895 Say Y here if you want to use the second built-in 10/100 Fast
1896 ethernet controller on some Motorola ColdFire processors.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001897
1898config NE_H8300
1899 tristate "NE2000 compatible support for H8/300"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001900 depends on H8300
Linus Torvalds1da177e2005-04-16 15:20:36 -07001901 help
1902 Say Y here if you want to use the NE2000 compatible
1903 controller on the Renesas H8/300 processor.
1904
1905source "drivers/net/fec_8xx/Kconfig"
Pantelis Antoniou48257c42005-10-28 16:25:58 -04001906source "drivers/net/fs_enet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001907
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001908endif # NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -07001909
1910#
1911# Gigabit Ethernet
1912#
1913
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001914menuconfig NETDEV_1000
1915 bool "Ethernet (1000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07001916 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001917 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02001918 ---help---
1919 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
1920 type of Local Area Network (LAN) in universities and companies.
1921
1922 Say Y here to get to see options for Gigabit Ethernet drivers.
1923 This option alone does not add any kernel code.
1924 Note that drivers supporting both 100 and 1000 MBit may be listed
1925 under "Ethernet (10 or 100MBit)" instead.
1926
1927 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001928
1929if NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07001930
1931config ACENIC
1932 tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
1933 depends on PCI
1934 ---help---
1935 Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
1936 GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
1937 adapter. The driver allows for using the Jumbo Frame option (9000
1938 bytes/frame) however it requires that your switches can handle this
1939 as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
1940 line.
1941
1942 To compile this driver as a module, choose M here: the
1943 module will be called acenic.
1944
1945config ACENIC_OMIT_TIGON_I
1946 bool "Omit support for old Tigon I based AceNICs"
1947 depends on ACENIC
1948 help
1949 Say Y here if you only have Tigon II based AceNICs and want to leave
1950 out support for the older Tigon I based cards which are no longer
1951 being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
1952 version)). This will reduce the size of the driver object by
1953 app. 100KB. If you are not sure whether your card is a Tigon I or a
1954 Tigon II, say N here.
1955
1956 The safe and default value for this is N.
1957
1958config DL2K
Komurodf950822007-08-13 09:45:41 +09001959 tristate "DL2000/TC902x-based Gigabit Ethernet support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001960 depends on PCI
1961 select CRC32
1962 help
Komurodf950822007-08-13 09:45:41 +09001963 This driver supports DL2000/TC902x-based Gigabit ethernet cards,
1964 which includes
Linus Torvalds1da177e2005-04-16 15:20:36 -07001965 D-Link DGE-550T Gigabit Ethernet Adapter.
1966 D-Link DL2000-based Gigabit Ethernet Adapter.
Komurodf950822007-08-13 09:45:41 +09001967 Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001968
1969 To compile this driver as a module, choose M here: the
1970 module will be called dl2k.
1971
1972config E1000
1973 tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
1974 depends on PCI
1975 ---help---
1976 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
1977 adapters. For more information on how to identify your adapter, go
1978 to the Adapter & Driver ID Guide at:
1979
1980 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
1981
1982 For general information and support, go to the Intel support
1983 website at:
1984
1985 <http://support.intel.com>
1986
1987 More specific information on configuring the driver is in
1988 <file:Documentation/networking/e1000.txt>.
1989
1990 To compile this driver as a module, choose M here and read
1991 <file:Documentation/networking/net-modules.txt>. The module
1992 will be called e1000.
1993
1994config E1000_NAPI
1995 bool "Use Rx Polling (NAPI)"
1996 depends on E1000
1997 help
1998 NAPI is a new driver API designed to reduce CPU and interrupt load
1999 when the driver is receiving lots of packets from the card. It is
2000 still somewhat experimental and thus not yet enabled by default.
2001
2002 If your estimated Rx load is 10kpps or more, or if the card will be
2003 deployed on potentially unfriendly networks (e.g. in a firewall),
2004 then say Y here.
2005
2006 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
2007 information.
2008
2009 If in doubt, say N.
2010
Jesse Brandeburg35ec56b2006-01-18 13:01:30 -08002011config E1000_DISABLE_PACKET_SPLIT
2012 bool "Disable Packet Split for PCI express adapters"
2013 depends on E1000
2014 help
2015 Say Y here if you want to use the legacy receive path for PCI express
James Ring9e6b4872006-03-22 00:51:11 +01002016 hardware.
Jesse Brandeburg35ec56b2006-01-18 13:01:30 -08002017
2018 If in doubt, say N.
2019
Auke Kokbc7f75f2007-09-17 12:30:59 -07002020config E1000E
2021 tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
2022 depends on PCI
2023 ---help---
2024 This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
2025 ethernet family of adapters. For PCI or PCI-X e1000 adapters,
2026 use the regular e1000 driver For more information on how to
2027 identify your adapter, go to the Adapter & Driver ID Guide at:
2028
2029 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2030
2031 For general information and support, go to the Intel support
2032 website at:
2033
2034 <http://support.intel.com>
2035
2036 More specific information on configuring the driver is in
2037 <file:Documentation/networking/e1000e.txt>.
2038
2039 To compile this driver as a module, choose M here and read
2040 <file:Documentation/networking/net-modules.txt>. The module
2041 will be called e1000e.
2042
Lennert Buytenhek15d014d2005-11-11 18:23:13 +01002043source "drivers/net/ixp2000/Kconfig"
2044
Linus Torvalds1da177e2005-04-16 15:20:36 -07002045config MYRI_SBUS
2046 tristate "MyriCOM Gigabit Ethernet support"
2047 depends on SBUS
2048 help
2049 This driver supports MyriCOM Sbus gigabit Ethernet cards.
2050
2051 To compile this driver as a module, choose M here: the module
2052 will be called myri_sbus. This is recommended.
2053
2054config NS83820
Jon Mason47c51432006-02-12 11:53:04 -06002055 tristate "National Semiconductor DP83820 support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002056 depends on PCI
2057 help
2058 This is a driver for the National Semiconductor DP83820 series
2059 of gigabit ethernet MACs. Cards using this chipset include
2060 the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
2061 SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of
2062 zero copy.
2063
2064config HAMACHI
2065 tristate "Packet Engines Hamachi GNIC-II support"
2066 depends on PCI
2067 select MII
2068 help
2069 If you have a Gigabit Ethernet card of this type, say Y and read
2070 the Ethernet-HOWTO, available from
2071 <http://www.tldp.org/docs.html#howto>.
2072
2073 To compile this driver as a module, choose M here and read
2074 <file:Documentation/networking/net-modules.txt>. The module will be
2075 called hamachi.
2076
2077config YELLOWFIN
2078 tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
2079 depends on PCI && EXPERIMENTAL
2080 select CRC32
2081 ---help---
2082 Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
2083 adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
2084 used by the Beowulf Linux cluster project. See
2085 <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
2086 information about this driver in particular and Beowulf in general.
2087
2088 To compile this driver as a module, choose M here: the module
2089 will be called yellowfin. This is recommended.
2090
2091config R8169
2092 tristate "Realtek 8169 gigabit ethernet support"
2093 depends on PCI
2094 select CRC32
2095 ---help---
2096 Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
2097
2098 To compile this driver as a module, choose M here: the module
2099 will be called r8169. This is recommended.
2100
2101config R8169_NAPI
2102 bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
2103 depends on R8169 && EXPERIMENTAL
2104 help
2105 NAPI is a new driver API designed to reduce CPU and interrupt load
2106 when the driver is receiving lots of packets from the card. It is
2107 still somewhat experimental and thus not yet enabled by default.
2108
2109 If your estimated Rx load is 10kpps or more, or if the card will be
2110 deployed on potentially unfriendly networks (e.g. in a firewall),
2111 then say Y here.
2112
2113 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
2114 information.
2115
2116 If in doubt, say N.
2117
2118config R8169_VLAN
2119 bool "VLAN support"
2120 depends on R8169 && VLAN_8021Q
2121 ---help---
2122 Say Y here for the r8169 driver to support the functions required
2123 by the kernel 802.1Q code.
2124
2125 If in doubt, say Y.
2126
Maciej W. Rozycki1a9e8542007-09-14 12:05:00 +01002127config SB1250_MAC
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002128 tristate "SB1250 Gigabit Ethernet support"
2129 depends on SIBYTE_SB1xxx_SOC
Maciej W. Rozyckif5279ff2007-09-21 12:52:10 +01002130 select PHYLIB
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002131 ---help---
2132 This driver supports Gigabit Ethernet interfaces based on the
2133 Broadcom SiByte family of System-On-a-Chip parts. They include
2134 the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
2135 and BCM1480 chips.
2136
2137 To compile this driver as a module, choose M here: the module
2138 will be called sb1250-mac.
2139
Francois Romieu890e8d02005-07-30 13:08:43 +02002140config SIS190
Francois Romieue7976372005-09-03 00:57:51 +02002141 tristate "SiS190/SiS191 gigabit ethernet support"
Adrian Bunke9985d52005-08-09 02:41:00 +02002142 depends on PCI
2143 select CRC32
2144 select MII
2145 ---help---
Francois Romieue7976372005-09-03 00:57:51 +02002146 Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
2147 a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
2148 appear in lan on motherboard designs which are based on SiS 965
2149 and SiS 966 south bridge.
Francois Romieu890e8d02005-07-30 13:08:43 +02002150
Adrian Bunke9985d52005-08-09 02:41:00 +02002151 To compile this driver as a module, choose M here: the module
2152 will be called sis190. This is recommended.
Francois Romieu890e8d02005-07-30 13:08:43 +02002153
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002154config SKGE
Stephen Hemminger7a160c72006-02-13 15:48:08 -08002155 tristate "New SysKonnect GigaEthernet support"
2156 depends on PCI
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002157 select CRC32
2158 ---help---
2159 This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
2160 and related Gigabit Ethernet adapters. It is a new smaller driver
Stephen Hemminger46a60f22005-09-09 12:54:56 -07002161 with better performance and more complete ethtool support.
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002162
2163 It does not support the link failover and network management
Stephen Hemminger5ad887f2007-09-15 19:35:14 -04002164 features that "portable" vendor supplied sk98lin driver does.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002165
Daniel Drakec6f0d752006-01-21 19:35:34 +00002166 This driver supports adapters based on the original Yukon chipset:
2167 Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
2168 Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
2169
2170 It does not support the newer Yukon2 chipset: a separate driver,
2171 sky2, is provided for Yukon2-based adapters.
2172
2173 To compile this driver as a module, choose M here: the module
2174 will be called skge. This is recommended.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002175
Stephen Hemminger678aa1f2007-10-16 12:15:54 -07002176config SKGE_DEBUG
2177 bool "Debugging interface"
2178 depends on SKGE && DEBUG_FS
2179 help
2180 This option adds the ability to dump driver state for debugging.
2181 The file debugfs/skge/ethX displays the state of the internal
2182 transmit and receive rings.
2183
2184 If unsure, say N.
2185
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002186config SKY2
Stephen Hemminger8a3e3bf2007-07-09 15:33:38 -07002187 tristate "SysKonnect Yukon2 support"
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002188 depends on PCI
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002189 select CRC32
2190 ---help---
Matt LaPlantecab00892006-10-03 22:36:44 +02002191 This driver supports Gigabit Ethernet adapters based on the
Daniel Drakec6f0d752006-01-21 19:35:34 +00002192 Marvell Yukon 2 chipset:
2193 Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
2194 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
2195
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002196 There is companion driver for the older Marvell Yukon and
2197 Genesis based adapters: skge.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002198
2199 To compile this driver as a module, choose M here: the module
2200 will be called sky2. This is recommended.
2201
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002202config SKY2_DEBUG
2203 bool "Debugging interface"
2204 depends on SKY2 && DEBUG_FS
2205 help
2206 This option adds the ability to dump driver state for debugging.
2207 The file debugfs/sky2/ethX displays the state of the internal
2208 transmit and receive rings.
Daniel Drakec6f0d752006-01-21 19:35:34 +00002209
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002210 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002211
Stephen Hemminger5ad887f2007-09-15 19:35:14 -04002212config SK98LIN
2213 tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)"
2214 depends on PCI
2215 ---help---
2216 Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
2217 compliant Gigabit Ethernet Adapter.
2218
2219 This driver supports the original Yukon chipset. This driver is
2220 deprecated and will be removed from the kernel in the near future,
2221 it has been replaced by the skge driver. skge is cleaner and
2222 seems to work better.
2223
2224 This driver does not support the newer Yukon2 chipset. A separate
2225 driver, sky2, is provided to support Yukon2-based adapters.
2226
2227 The following adapters are supported by this driver:
2228 - 3Com 3C940 Gigabit LOM Ethernet Adapter
2229 - 3Com 3C941 Gigabit LOM Ethernet Adapter
2230 - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
2231 - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
2232 - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
2233 - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
2234 - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
2235 - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
2236 - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
2237 - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
2238 - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
2239 - EG1032 v2 Instant Gigabit Network Adapter
2240 - EG1064 v2 Instant Gigabit Network Adapter
2241 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
2242 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron)
2243 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
2244 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
2245 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
2246 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn)
2247 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
2248 - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
2249 - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel)
2250 - Marvell RDK-8001 Adapter
2251 - Marvell RDK-8002 Adapter
2252 - Marvell RDK-8003 Adapter
2253 - Marvell RDK-8004 Adapter
2254 - Marvell RDK-8006 Adapter
2255 - Marvell RDK-8007 Adapter
2256 - Marvell RDK-8008 Adapter
2257 - Marvell RDK-8009 Adapter
2258 - Marvell RDK-8010 Adapter
2259 - Marvell RDK-8011 Adapter
2260 - Marvell RDK-8012 Adapter
2261 - Marvell RDK-8052 Adapter
2262 - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
2263 - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
2264 - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
2265 - SK-9521 10/100/1000Base-T Adapter
2266 - SK-9521 V2.0 10/100/1000Base-T Adapter
2267 - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
2268 - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
2269 - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
2270 - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
2271 - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
2272 - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
2273 - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
2274 - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
2275 - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
2276 - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
2277 - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
2278 - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
2279 - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
2280 - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
2281 - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
2282 - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
2283 - SMC EZ Card 1000 (SMC9452TXV.2)
2284
2285 The adapters support Jumbo Frames.
2286 The dual link adapters support link-failover and dual port features.
2287 Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support
2288 the scatter-gather functionality with sendfile(). Please refer to
2289 <file:Documentation/networking/sk98lin.txt> for more information about
2290 optional driver parameters.
2291 Questions concerning this driver may be addressed to:
2292 <linux@syskonnect.de>
2293
2294 If you want to compile this driver as a module ( = code which can be
2295 inserted in and removed from the running kernel whenever you want),
2296 say M here and read <file:Documentation/kbuild/modules.txt>. The module will
2297 be called sk98lin. This is recommended.
2298
Linus Torvalds1da177e2005-04-16 15:20:36 -07002299config VIA_VELOCITY
2300 tristate "VIA Velocity support"
Yoichi Yuasa73815532007-05-24 16:12:27 +09002301 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002302 select CRC32
2303 select CRC_CCITT
2304 select MII
2305 help
2306 If you have a VIA "Velocity" based network card say Y here.
2307
2308 To compile this driver as a module, choose M here. The module
2309 will be called via-velocity.
2310
2311config TIGON3
2312 tristate "Broadcom Tigon3 support"
2313 depends on PCI
2314 help
2315 This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
2316
2317 To compile this driver as a module, choose M here: the module
2318 will be called tg3. This is recommended.
2319
Michael Chanb6016b72005-05-26 13:03:09 -07002320config BNX2
2321 tristate "Broadcom NetXtremeII support"
2322 depends on PCI
Michael Chanfba9fe92006-06-12 22:21:25 -07002323 select CRC32
2324 select ZLIB_INFLATE
Michael Chanb6016b72005-05-26 13:03:09 -07002325 help
2326 This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
2327
2328 To compile this driver as a module, choose M here: the module
2329 will be called bnx2. This is recommended.
2330
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002331config SPIDER_NET
2332 tristate "Spider Gigabit Ethernet driver"
Kou Ishizaki3342cf0e2007-02-20 16:36:14 -06002333 depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
Christoph Hellwig9b158792006-03-15 11:30:44 +01002334 select FW_LOADER
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002335 help
2336 This driver supports the Gigabit Ethernet chips present on the
2337 Cell Processor-Based Blades from IBM.
2338
Zang Roy-r619115e123b82006-11-08 19:49:13 -08002339config TSI108_ETH
2340 tristate "Tundra TSI108 gigabit Ethernet support"
2341 depends on TSI108_BRIDGE
2342 help
2343 This driver supports Tundra TSI108 gigabit Ethernet ports.
2344 To compile this driver as a module, choose M here: the module
2345 will be called tsi108_eth.
2346
Masakazu Mokuno02c18892007-07-05 20:11:16 +09002347config GELIC_NET
2348 tristate "PS3 Gigabit Ethernet driver"
2349 depends on PPC_PS3
2350 help
2351 This driver supports the network device on the PS3 game
2352 console. This driver has built-in support for Ethernet.
2353
2354 To compile this driver as a module, choose M here: the
2355 module will be called ps3_gelic.
2356
Linus Torvalds1da177e2005-04-16 15:20:36 -07002357config GIANFAR
2358 tristate "Gianfar Ethernet"
Jon Loeligeref82a3062006-06-17 17:52:55 -05002359 depends on 85xx || 83xx || PPC_86xx
Andy Flemingbb40dcb2005-09-23 22:54:21 -04002360 select PHYLIB
Dave Jiangbf41a7c2007-04-12 10:57:06 -07002361 select CRC32
Linus Torvalds1da177e2005-04-16 15:20:36 -07002362 help
Jon Loeligeref82a3062006-06-17 17:52:55 -05002363 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
2364 and MPC86xx family of chips, and the FEC on the 8540.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002365
2366config GFAR_NAPI
2367 bool "NAPI Support"
2368 depends on GIANFAR
2369
Li Yangce973b12006-08-14 23:00:11 -07002370config UCC_GETH
Timur Tabi7d776cb2007-03-12 15:40:27 -05002371 tristate "Freescale QE Gigabit Ethernet"
2372 depends on QUICC_ENGINE
Jan Altenberg296baae2007-06-01 00:46:29 -07002373 select PHYLIB
Li Yangce973b12006-08-14 23:00:11 -07002374 help
Timur Tabi7d776cb2007-03-12 15:40:27 -05002375 This driver supports the Gigabit Ethernet mode of the QUICC Engine,
2376 which is available on some Freescale SOCs.
Li Yangce973b12006-08-14 23:00:11 -07002377
2378config UGETH_NAPI
2379 bool "NAPI Support"
2380 depends on UCC_GETH
2381
2382config UGETH_MAGIC_PACKET
2383 bool "Magic Packet detection support"
2384 depends on UCC_GETH
2385
2386config UGETH_FILTERING
2387 bool "Mac address filtering support"
2388 depends on UCC_GETH
2389
Michael Reissd5b90492007-04-13 01:26:19 -05002390config UGETH_TX_ON_DEMAND
2391 bool "Transmit on Demand support"
Li Yangce973b12006-08-14 23:00:11 -07002392 depends on UCC_GETH
2393
Linus Torvalds1da177e2005-04-16 15:20:36 -07002394config MV643XX_ETH
2395 tristate "MV-643XX Ethernet support"
Ralf Baechle688b3d72007-07-09 16:29:16 +01002396 depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32)
Dale Farnsworthcd6478c2006-03-03 10:01:08 -07002397 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07002398 help
2399 This driver supports the gigabit Ethernet on the Marvell MV643XX
2400 chipset which is used in the Momenco Ocelot C and Jaguar ATX and
2401 Pegasos II, amongst other PPC and MIPS boards.
2402
Ron Mercer5a4faa872006-07-25 00:40:21 -07002403config QLA3XXX
2404 tristate "QLogic QLA3XXX Network Driver Support"
2405 depends on PCI
2406 help
2407 This driver supports QLogic ISP3XXX gigabit Ethernet cards.
2408
2409 To compile this driver as a module, choose M here: the module
2410 will be called qla3xxx.
2411
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002412config ATL1
2413 tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
Jay Cliburna1ca14b2007-02-14 20:12:13 -06002414 depends on PCI && EXPERIMENTAL
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002415 select CRC32
2416 select MII
2417 help
2418 This driver supports the Attansic L1 gigabit ethernet adapter.
2419
2420 To compile this driver as a module, choose M here. The module
2421 will be called atl1.
2422
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002423endif # NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002424
2425#
2426# 10 Gigabit Ethernet
2427#
2428
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002429menuconfig NETDEV_10000
2430 bool "Ethernet (10000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002431 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002432 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02002433 ---help---
2434 Say Y here to get to see options for 10 Gigabit Ethernet drivers.
2435 This option alone does not add any kernel code.
2436
2437 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002438
2439if NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002440
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002441config CHELSIO_T1
2442 tristate "Chelsio 10Gb Ethernet support"
2443 depends on PCI
Stephen Hemminger57834ca2006-12-01 16:36:19 -08002444 select CRC32
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002445 help
Stephen Hemmingerf1d3d382006-12-01 16:36:16 -08002446 This driver supports Chelsio gigabit and 10-gigabit
2447 Ethernet cards. More information about adapter features and
2448 performance tuning is in <file:Documentation/networking/cxgb.txt>.
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002449
2450 For general information about Chelsio and our products, visit
2451 our website at <http://www.chelsio.com>.
2452
2453 For customer support, please visit our customer support page at
2454 <http://www.chelsio.com/support.htm>.
2455
2456 Please send feedback to <linux-bugs@chelsio.com>.
2457
2458 To compile this driver as a module, choose M here: the module
2459 will be called cxgb.
2460
Stephen Hemminger352c4172006-12-01 16:36:17 -08002461config CHELSIO_T1_1G
2462 bool "Chelsio gigabit Ethernet support"
2463 depends on CHELSIO_T1
2464 help
2465 Enables support for Chelsio's gigabit Ethernet PCI cards. If you
2466 are using only 10G cards say 'N' here.
2467
Stephen Hemminger7fe26a62006-12-08 11:08:33 -08002468config CHELSIO_T1_NAPI
2469 bool "Use Rx Polling (NAPI)"
2470 depends on CHELSIO_T1
2471 default y
2472 help
2473 NAPI is a driver API designed to reduce CPU and interrupt load
2474 when the driver is receiving lots of packets from the card.
2475
Divy Le Ray4d22de32007-01-18 22:04:14 -05002476config CHELSIO_T3
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002477 tristate "Chelsio Communications T3 10Gb Ethernet support"
2478 depends on PCI
Divy Le Ray2e283962007-03-18 13:10:06 -07002479 select FW_LOADER
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002480 help
2481 This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
2482 adapters.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002483
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002484 For general information about Chelsio and our products, visit
2485 our website at <http://www.chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002486
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002487 For customer support, please visit our customer support page at
2488 <http://www.chelsio.com/support.htm>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002489
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002490 Please send feedback to <linux-bugs@chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002491
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002492 To compile this driver as a module, choose M here: the module
2493 will be called cxgb3.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002494
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002495config EHEA
2496 tristate "eHEA Ethernet support"
2497 depends on IBMEBUS
Jan-Bernd Themannd4dc4ec2007-09-25 16:16:34 -07002498 select INET_LRO
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002499 ---help---
2500 This driver supports the IBM pSeries eHEA ethernet adapter.
2501
2502 To compile the driver as a module, choose M here. The module
2503 will be called ehea.
2504
Auke Kok9a799d72007-09-15 14:07:45 -07002505config IXGBE
2506 tristate "Intel(R) 10GbE PCI Express adapters support"
2507 depends on PCI
2508 ---help---
2509 This driver supports Intel(R) 10GbE PCI Express family of
2510 adapters. For more information on how to identify your adapter, go
2511 to the Adapter & Driver ID Guide at:
2512
2513 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2514
2515 For general information and support, go to the Intel support
2516 website at:
2517
2518 <http://support.intel.com>
2519
2520 More specific information on configuring the driver is in
2521 <file:Documentation/networking/ixgbe.txt>.
2522
2523 To compile this driver as a module, choose M here and read
2524 <file:Documentation/networking/net-modules.txt>. The module
2525 will be called ixgbe.
2526
Linus Torvalds1da177e2005-04-16 15:20:36 -07002527config IXGB
2528 tristate "Intel(R) PRO/10GbE support"
2529 depends on PCI
2530 ---help---
Auke Kok9a799d72007-09-15 14:07:45 -07002531 This driver supports Intel(R) PRO/10GbE family of adapters for
2532 PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
2533 instead. For more information on how to identify your adapter, go
Linus Torvalds1da177e2005-04-16 15:20:36 -07002534 to the Adapter & Driver ID Guide at:
2535
2536 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2537
2538 For general information and support, go to the Intel support
2539 website at:
2540
2541 <http://support.intel.com>
2542
2543 More specific information on configuring the driver is in
2544 <file:Documentation/networking/ixgb.txt>.
2545
2546 To compile this driver as a module, choose M here and read
2547 <file:Documentation/networking/net-modules.txt>. The module
2548 will be called ixgb.
2549
2550config IXGB_NAPI
2551 bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
2552 depends on IXGB && EXPERIMENTAL
2553 help
2554 NAPI is a new driver API designed to reduce CPU and interrupt load
2555 when the driver is receiving lots of packets from the card. It is
2556 still somewhat experimental and thus not yet enabled by default.
2557
2558 If your estimated Rx load is 10kpps or more, or if the card will be
2559 deployed on potentially unfriendly networks (e.g. in a firewall),
2560 then say Y here.
2561
2562 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
2563 information.
2564
2565 If in doubt, say N.
2566
2567config S2IO
2568 tristate "S2IO 10Gbe XFrame NIC"
2569 depends on PCI
2570 ---help---
2571 This driver supports the 10Gbe XFrame NIC of S2IO.
Akinobu Mita9eb343a2005-10-21 19:06:42 +09002572 More specific information on configuring the driver is in
2573 <file:Documentation/networking/s2io.txt>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002574
2575config S2IO_NAPI
2576 bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
2577 depends on S2IO && EXPERIMENTAL
2578 help
2579 NAPI is a new driver API designed to reduce CPU and interrupt load
2580 when the driver is receiving lots of packets from the card. It is
2581 still somewhat experimental and thus not yet enabled by default.
2582
2583 If your estimated Rx load is 10kpps or more, or if the card will be
2584 deployed on potentially unfriendly networks (e.g. in a firewall),
2585 then say Y here.
2586
2587 See <file:Documentation/networking/NAPI_HOWTO.txt> for more
2588 information.
2589
2590 If in doubt, say N.
2591
Brice Goglin0da34b62006-05-23 06:10:15 -04002592config MYRI10GE
2593 tristate "Myricom Myri-10G Ethernet support"
2594 depends on PCI
2595 select FW_LOADER
2596 select CRC32
Andrew Gallatin1e6e9342007-09-17 11:37:42 -07002597 select INET_LRO
Brice Goglin0da34b62006-05-23 06:10:15 -04002598 ---help---
2599 This driver supports Myricom Myri-10G Dual Protocol interface in
2600 Ethernet mode. If the eeprom on your board is not recent enough,
2601 you will need a newer firmware image.
2602 You may get this image or more information, at:
2603
Brice Goglind2794902006-09-05 21:58:50 -04002604 <http://www.myri.com/scs/download-Myri10GE.html>
Brice Goglin0da34b62006-05-23 06:10:15 -04002605
2606 To compile this driver as a module, choose M here and read
2607 <file:Documentation/networking/net-modules.txt>. The module
2608 will be called myri10ge.
2609
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002610config NETXEN_NIC
2611 tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
Randy Dunlap5ac36612006-11-16 21:39:11 -08002612 depends on PCI
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002613 help
2614 This enables the support for NetXen's Gigabit Ethernet card.
2615
David S. Millera3138df2007-10-09 01:54:01 -07002616config NIU
2617 tristate "Sun Neptune 10Gbit Ethernet support"
2618 depends on PCI
2619 help
2620 This enables support for cards based upon Sun's
2621 Neptune chipset.
2622
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002623config PASEMI_MAC
2624 tristate "PA Semi 1/10Gbit MAC"
2625 depends on PPC64 && PCI
Olof Johanssonbb6e9592007-05-08 00:47:54 -05002626 select PHYLIB
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002627 help
2628 This driver supports the on-chip 1/10Gbit Ethernet controller on
2629 PA Semi's PWRficient line of chips.
2630
Roland Dreier225c7b12007-05-08 18:00:38 -07002631config MLX4_CORE
2632 tristate
2633 depends on PCI
2634 default n
2635
2636config MLX4_DEBUG
2637 bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
Paul Mundtf550d942007-05-10 12:50:28 +09002638 depends on MLX4_CORE
Roland Dreier225c7b12007-05-08 18:00:38 -07002639 default y
2640 ---help---
2641 This option causes debugging code to be compiled into the
2642 mlx4_core driver. The output can be turned on via the
2643 debug_level module parameter (which can also be set after
2644 the driver is loaded through sysfs).
2645
Andy Gospodarek1a348cc2007-09-17 18:50:36 -07002646config TEHUTI
2647 tristate "Tehuti Networks 10G Ethernet"
2648 depends on PCI
2649 help
2650 Tehuti Networks 10G Ethernet NIC
2651
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002652endif # NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002653
Linus Torvalds1da177e2005-04-16 15:20:36 -07002654source "drivers/net/tokenring/Kconfig"
2655
2656source "drivers/net/wireless/Kconfig"
2657
Jeff Garzik5b2fc492007-05-09 21:31:55 -04002658source "drivers/net/usb/Kconfig"
2659
Linus Torvalds1da177e2005-04-16 15:20:36 -07002660source "drivers/net/pcmcia/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002661
2662source "drivers/net/wan/Kconfig"
2663
2664source "drivers/atm/Kconfig"
2665
2666source "drivers/s390/net/Kconfig"
2667
Jeremy Fitzhardinge0d160212007-07-17 18:37:06 -07002668config XEN_NETDEV_FRONTEND
2669 tristate "Xen network device frontend driver"
2670 depends on XEN
2671 default y
2672 help
2673 The network device frontend driver allows the kernel to
2674 access network devices exported exported by a virtual
2675 machine containing a physical network device driver. The
2676 frontend driver is intended for unprivileged guest domains;
2677 if you are compiling a kernel for a Xen guest, you almost
2678 certainly want to enable this.
2679
Linus Torvalds1da177e2005-04-16 15:20:36 -07002680config ISERIES_VETH
2681 tristate "iSeries Virtual Ethernet driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002682 depends on PPC_ISERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07002683
Matt Porterf89efd52005-09-09 12:10:10 -07002684config RIONET
2685 tristate "RapidIO Ethernet over messaging driver support"
Randy Dunlapa81c52a2006-11-01 21:18:58 -08002686 depends on RAPIDIO
Matt Porterf89efd52005-09-09 12:10:10 -07002687
2688config RIONET_TX_SIZE
2689 int "Number of outbound queue entries"
2690 depends on RIONET
2691 default "128"
2692
2693config RIONET_RX_SIZE
2694 int "Number of inbound queue entries"
2695 depends on RIONET
2696 default "128"
2697
Linus Torvalds1da177e2005-04-16 15:20:36 -07002698config FDDI
2699 bool "FDDI driver support"
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002700 depends on (PCI || EISA || TC)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002701 help
2702 Fiber Distributed Data Interface is a high speed local area network
2703 design; essentially a replacement for high speed Ethernet. FDDI can
2704 run over copper or fiber. If you are connected to such a network and
2705 want a driver for the FDDI card in your computer, say Y here (and
2706 then also Y to the driver for your FDDI card, below). Most people
2707 will say N.
2708
2709config DEFXX
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002710 tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
2711 depends on FDDI && (PCI || EISA || TC)
2712 ---help---
2713 This is support for the DIGITAL series of TURBOchannel (DEFTA),
2714 EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
2715 to a local FDDI network.
2716
2717 To compile this driver as a module, choose M here: the module
2718 will be called defxx. If unsure, say N.
2719
2720config DEFXX_MMIO
2721 bool
2722 prompt "Use MMIO instead of PIO" if PCI || EISA
2723 depends on DEFXX
2724 default n if PCI || EISA
2725 default y
2726 ---help---
2727 This instructs the driver to use EISA or PCI memory-mapped I/O
2728 (MMIO) as appropriate instead of programmed I/O ports (PIO).
2729 Enabling this gives an improvement in processing time in parts
2730 of the driver, but it may cause problems with EISA (DEFEA)
2731 adapters. TURBOchannel does not have the concept of I/O ports,
2732 so MMIO is always used for these (DEFTA) adapters.
2733
2734 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002735
2736config SKFP
2737 tristate "SysKonnect FDDI PCI support"
2738 depends on FDDI && PCI
Akinobu Mitabc63eb92006-12-19 13:09:08 -08002739 select BITREVERSE
Linus Torvalds1da177e2005-04-16 15:20:36 -07002740 ---help---
2741 Say Y here if you have a SysKonnect FDDI PCI adapter.
2742 The following adapters are supported by this driver:
2743 - SK-5521 (SK-NET FDDI-UP)
2744 - SK-5522 (SK-NET FDDI-UP DAS)
2745 - SK-5541 (SK-NET FDDI-FP)
2746 - SK-5543 (SK-NET FDDI-LP)
2747 - SK-5544 (SK-NET FDDI-LP DAS)
2748 - SK-5821 (SK-NET FDDI-UP64)
2749 - SK-5822 (SK-NET FDDI-UP64 DAS)
2750 - SK-5841 (SK-NET FDDI-FP64)
2751 - SK-5843 (SK-NET FDDI-LP64)
2752 - SK-5844 (SK-NET FDDI-LP64 DAS)
2753 - Netelligent 100 FDDI DAS Fibre SC
2754 - Netelligent 100 FDDI SAS Fibre SC
2755 - Netelligent 100 FDDI DAS UTP
2756 - Netelligent 100 FDDI SAS UTP
2757 - Netelligent 100 FDDI SAS Fibre MIC
2758
2759 Read <file:Documentation/networking/skfp.txt> for information about
2760 the driver.
2761
2762 Questions concerning this driver can be addressed to:
2763 <linux@syskonnect.de>
2764
2765 To compile this driver as a module, choose M here: the module
2766 will be called skfp. This is recommended.
2767
2768config HIPPI
2769 bool "HIPPI driver support (EXPERIMENTAL)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002770 depends on EXPERIMENTAL && INET && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002771 help
2772 HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
2773 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
2774 can run over copper (25m) or fiber (300m on multi-mode or 10km on
2775 single-mode). HIPPI networks are commonly used for clusters and to
2776 connect to super computers. If you are connected to a HIPPI network
2777 and have a HIPPI network card in your computer that you want to use
2778 under Linux, say Y here (you must also remember to enable the driver
2779 for your HIPPI card below). Most people will say N here.
2780
2781config ROADRUNNER
2782 tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
2783 depends on HIPPI && PCI
2784 help
2785 Say Y here if this is your PCI HIPPI network card.
2786
2787 To compile this driver as a module, choose M here: the module
2788 will be called rrunner. If unsure, say N.
2789
2790config ROADRUNNER_LARGE_RINGS
2791 bool "Use large TX/RX rings (EXPERIMENTAL)"
2792 depends on ROADRUNNER
2793 help
2794 If you say Y here, the RoadRunner driver will preallocate up to 2 MB
2795 of additional memory to allow for fastest operation, both for
2796 transmitting and receiving. This memory cannot be used by any other
2797 kernel code or by user space programs. Say Y here only if you have
2798 the memory.
2799
2800config PLIP
2801 tristate "PLIP (parallel port) support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002802 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07002803 ---help---
2804 PLIP (Parallel Line Internet Protocol) is used to create a
2805 reasonably fast mini network consisting of two (or, rarely, more)
2806 local machines. A PLIP link from a Linux box is a popular means to
2807 install a Linux distribution on a machine which doesn't have a
2808 CD-ROM drive (a minimal system has to be transferred with floppies
2809 first). The kernels on both machines need to have this PLIP option
2810 enabled for this to work.
2811
2812 The PLIP driver has two modes, mode 0 and mode 1. The parallel
2813 ports (the connectors at the computers with 25 holes) are connected
2814 with "null printer" or "Turbo Laplink" cables which can transmit 4
2815 bits at a time (mode 0) or with special PLIP cables, to be used on
2816 bidirectional parallel ports only, which can transmit 8 bits at a
2817 time (mode 1); you can find the wiring of these cables in
2818 <file:Documentation/networking/PLIP.txt>. The cables can be up to
2819 15m long. Mode 0 works also if one of the machines runs DOS/Windows
2820 and has some PLIP software installed, e.g. the Crynwr PLIP packet
2821 driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
2822 and winsock or NCSA's telnet.
2823
2824 If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
2825 as the NET-3-HOWTO, both available from
2826 <http://www.tldp.org/docs.html#howto>. Note that the PLIP
2827 protocol has been changed and this PLIP driver won't work together
2828 with the PLIP support in Linux versions 1.0.x. This option enlarges
2829 your kernel by about 8 KB.
2830
2831 To compile this driver as a module, choose M here and read
2832 <file:Documentation/networking/net-modules.txt>. The module will be
2833 called plip. If unsure, say Y or M, in case you buy a laptop
2834 later.
2835
2836config PPP
2837 tristate "PPP (point-to-point protocol) support"
Ralf Baechleb6e37e52006-07-14 12:15:40 +01002838 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07002839 ---help---
2840 PPP (Point to Point Protocol) is a newer and better SLIP. It serves
2841 the same purpose: sending Internet traffic over telephone (and other
2842 serial) lines. Ask your access provider if they support it, because
2843 otherwise you can't use it; most Internet access providers these
2844 days support PPP rather than SLIP.
2845
2846 To use PPP, you need an additional program called pppd as described
2847 in the PPP-HOWTO, available at
2848 <http://www.tldp.org/docs.html#howto>. Make sure that you have
2849 the version of pppd recommended in <file:Documentation/Changes>.
2850 The PPP option enlarges your kernel by about 16 KB.
2851
2852 There are actually two versions of PPP: the traditional PPP for
2853 asynchronous lines, such as regular analog phone lines, and
2854 synchronous PPP which can be used over digital ISDN lines for
2855 example. If you want to use PPP over phone lines or other
2856 asynchronous serial lines, you need to say Y (or M) here and also to
2857 the next option, "PPP support for async serial ports". For PPP over
2858 synchronous lines, you should say Y (or M) here and to "Support
2859 synchronous PPP", below.
2860
2861 If you said Y to "Version information on all symbols" above, then
2862 you cannot compile the PPP driver into the kernel; you can then only
2863 compile it as a module. To compile this driver as a module, choose M
2864 here and read <file:Documentation/networking/net-modules.txt>.
2865 The module will be called ppp_generic.
2866
2867config PPP_MULTILINK
2868 bool "PPP multilink support (EXPERIMENTAL)"
2869 depends on PPP && EXPERIMENTAL
2870 help
2871 PPP multilink is a protocol (defined in RFC 1990) which allows you
2872 to combine several (logical or physical) lines into one logical PPP
2873 connection, so that you can utilize your full bandwidth.
2874
2875 This has to be supported at the other end as well and you need a
2876 version of the pppd daemon which understands the multilink protocol.
2877
2878 If unsure, say N.
2879
2880config PPP_FILTER
2881 bool "PPP filtering"
2882 depends on PPP
2883 help
2884 Say Y here if you want to be able to filter the packets passing over
2885 PPP interfaces. This allows you to control which packets count as
2886 activity (i.e. which packets will reset the idle timer or bring up
Jon Mason47c51432006-02-12 11:53:04 -06002887 a demand-dialed link) and which packets are to be dropped entirely.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002888 You need to say Y here if you wish to use the pass-filter and
2889 active-filter options to pppd.
2890
2891 If unsure, say N.
2892
2893config PPP_ASYNC
2894 tristate "PPP support for async serial ports"
2895 depends on PPP
2896 select CRC_CCITT
2897 ---help---
2898 Say Y (or M) here if you want to be able to use PPP over standard
2899 asynchronous serial ports, such as COM1 or COM2 on a PC. If you use
2900 a modem (not a synchronous or ISDN modem) to contact your ISP, you
2901 need this option.
2902
2903 To compile this driver as a module, choose M here.
2904
2905 If unsure, say Y.
2906
2907config PPP_SYNC_TTY
2908 tristate "PPP support for sync tty ports"
2909 depends on PPP
2910 help
2911 Say Y (or M) here if you want to be able to use PPP over synchronous
2912 (HDLC) tty devices, such as the SyncLink adapter. These devices
2913 are often used for high-speed leased lines like T1/E1.
2914
2915 To compile this driver as a module, choose M here.
2916
2917config PPP_DEFLATE
2918 tristate "PPP Deflate compression"
2919 depends on PPP
2920 select ZLIB_INFLATE
2921 select ZLIB_DEFLATE
2922 ---help---
2923 Support for the Deflate compression method for PPP, which uses the
2924 Deflate algorithm (the same algorithm that gzip uses) to compress
2925 each PPP packet before it is sent over the wire. The machine at the
2926 other end of the PPP link (usually your ISP) has to support the
2927 Deflate compression method as well for this to be useful. Even if
2928 they don't support it, it is safe to say Y here.
2929
2930 To compile this driver as a module, choose M here.
2931
2932config PPP_BSDCOMP
2933 tristate "PPP BSD-Compress compression"
2934 depends on PPP
2935 ---help---
2936 Support for the BSD-Compress compression method for PPP, which uses
2937 the LZW compression method to compress each PPP packet before it is
2938 sent over the wire. The machine at the other end of the PPP link
2939 (usually your ISP) has to support the BSD-Compress compression
2940 method as well for this to be useful. Even if they don't support it,
2941 it is safe to say Y here.
2942
2943 The PPP Deflate compression method ("PPP Deflate compression",
2944 above) is preferable to BSD-Compress, because it compresses better
2945 and is patent-free.
2946
2947 Note that the BSD compression code will always be compiled as a
2948 module; it is called bsd_comp and will show up in the directory
2949 modules once you have said "make modules". If unsure, say N.
2950
Matt Domschb3f9b922005-11-08 09:40:47 -08002951config PPP_MPPE
2952 tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
2953 depends on PPP && EXPERIMENTAL
2954 select CRYPTO
2955 select CRYPTO_SHA1
2956 select CRYPTO_ARC4
Patrick McHardybcbaecb2006-10-25 16:49:36 +10002957 select CRYPTO_ECB
Matt Domschb3f9b922005-11-08 09:40:47 -08002958 ---help---
2959 Support for the MPPE Encryption protocol, as employed by the
2960 Microsoft Point-to-Point Tunneling Protocol.
2961
2962 See http://pptpclient.sourceforge.net/ for information on
2963 configuring PPTP clients and servers to utilize this method.
2964
Linus Torvalds1da177e2005-04-16 15:20:36 -07002965config PPPOE
2966 tristate "PPP over Ethernet (EXPERIMENTAL)"
2967 depends on EXPERIMENTAL && PPP
2968 help
2969 Support for PPP over Ethernet.
2970
2971 This driver requires the latest version of pppd from the CVS
2972 repository at cvs.samba.org. Alternatively, see the
2973 RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
2974 which contains instruction on how to use this driver (under
2975 the heading "Kernel mode PPPoE").
2976
2977config PPPOATM
2978 tristate "PPP over ATM"
2979 depends on ATM && PPP
2980 help
2981 Support PPP (Point to Point Protocol) encapsulated in ATM frames.
2982 This implementation does not yet comply with section 8 of RFC2364,
2983 which can lead to bad results if the ATM peer loses state and
2984 changes its encapsulation unilaterally.
2985
James Chapman3557baa2007-06-27 15:49:24 -07002986config PPPOL2TP
2987 tristate "PPP over L2TP (EXPERIMENTAL)"
James Chapman143cf352007-07-30 18:51:48 -07002988 depends on EXPERIMENTAL && PPP && INET
James Chapman3557baa2007-06-27 15:49:24 -07002989 help
2990 Support for PPP-over-L2TP socket family. L2TP is a protocol
2991 used by ISPs and enterprises to tunnel PPP traffic over UDP
2992 tunnels. L2TP is replacing PPTP for VPN uses.
2993
2994 This kernel component handles only L2TP data packets: a
2995 userland daemon handles L2TP the control protocol (tunnel
2996 and session setup). One such daemon is OpenL2TP
2997 (http://openl2tp.sourceforge.net/).
2998
Linus Torvalds1da177e2005-04-16 15:20:36 -07002999config SLIP
3000 tristate "SLIP (serial line) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07003001 ---help---
3002 Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
3003 connect to your Internet service provider or to connect to some
3004 other local Unix box or if you want to configure your Linux box as a
3005 Slip/CSlip server for other people to dial in. SLIP (Serial Line
3006 Internet Protocol) is a protocol used to send Internet traffic over
3007 serial connections such as telephone lines or null modem cables;
3008 nowadays, the protocol PPP is more commonly used for this same
3009 purpose.
3010
3011 Normally, your access provider has to support SLIP in order for you
3012 to be able to use it, but there is now a SLIP emulator called SLiRP
3013 around (available from
3014 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3015 allows you to use SLIP over a regular dial up shell connection. If
3016 you plan to use SLiRP, make sure to say Y to CSLIP, below. The
3017 NET-3-HOWTO, available from
3018 <http://www.tldp.org/docs.html#howto>, explains how to
3019 configure SLIP. Note that you don't need this option if you just
3020 want to run term (term is a program which gives you almost full
3021 Internet connectivity if you have a regular dial up shell account on
3022 some Internet connected Unix computer. Read
3023 <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
3024 support will enlarge your kernel by about 4 KB. If unsure, say N.
3025
3026 To compile this driver as a module, choose M here and read
3027 <file:Documentation/networking/net-modules.txt>. The module will be
3028 called slip.
3029
3030config SLIP_COMPRESSED
3031 bool "CSLIP compressed headers"
3032 depends on SLIP
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003033 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07003034 ---help---
3035 This protocol is faster than SLIP because it uses compression on the
3036 TCP/IP headers (not on the data itself), but it has to be supported
3037 on both ends. Ask your access provider if you are not sure and
3038 answer Y, just in case. You will still be able to use plain SLIP. If
3039 you plan to use SLiRP, the SLIP emulator (available from
3040 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3041 allows you to use SLIP over a regular dial up shell connection, you
3042 definitely want to say Y here. The NET-3-HOWTO, available from
3043 <http://www.tldp.org/docs.html#howto>, explains how to configure
3044 CSLIP. This won't enlarge your kernel.
3045
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003046config SLHC
3047 tristate
3048 help
3049 This option enables Van Jacobsen serial line header compression
3050 routines.
3051
Linus Torvalds1da177e2005-04-16 15:20:36 -07003052config SLIP_SMART
3053 bool "Keepalive and linefill"
3054 depends on SLIP
3055 help
3056 Adds additional capabilities to the SLIP driver to support the
3057 RELCOM line fill and keepalive monitoring. Ideal on poor quality
3058 analogue lines.
3059
3060config SLIP_MODE_SLIP6
3061 bool "Six bit SLIP encapsulation"
3062 depends on SLIP
3063 help
3064 Just occasionally you may need to run IP over hostile serial
3065 networks that don't pass all control characters or are only seven
3066 bit. Saying Y here adds an extra mode you can use with SLIP:
3067 "slip6". In this mode, SLIP will only send normal ASCII symbols over
3068 the serial device. Naturally, this has to be supported at the other
3069 end of the link as well. It's good enough, for example, to run IP
3070 over the async ports of a Camtec JNT Pad. If unsure, say N.
3071
3072config NET_FC
3073 bool "Fibre Channel driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07003074 depends on SCSI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07003075 help
3076 Fibre Channel is a high speed serial protocol mainly used to connect
3077 large storage devices to the computer; it is compatible with and
3078 intended to replace SCSI.
3079
3080 If you intend to use Fibre Channel, you need to have a Fibre channel
3081 adaptor card in your computer; say Y here and to the driver for your
3082 adaptor below. You also should have said Y to "SCSI support" and
3083 "SCSI generic support".
3084
3085config SHAPER
Jiri Slaby3b6a7922006-11-06 14:34:48 -08003086 tristate "Traffic Shaper (OBSOLETE)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07003087 depends on EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07003088 ---help---
3089 The traffic shaper is a virtual network device that allows you to
3090 limit the rate of outgoing data flow over some other network device.
3091 The traffic that you want to slow down can then be routed through
3092 these virtual devices. See
3093 <file:Documentation/networking/shaper.txt> for more information.
3094
Jiri Slaby3b6a7922006-11-06 14:34:48 -08003095 An alternative to this traffic shaper are traffic schedulers which
3096 you'll get if you say Y to "QoS and/or fair queuing" in
3097 "Networking options".
Linus Torvalds1da177e2005-04-16 15:20:36 -07003098
Linus Torvalds1da177e2005-04-16 15:20:36 -07003099 To compile this driver as a module, choose M here: the module
3100 will be called shaper. If unsure, say N.
3101
3102config NETCONSOLE
3103 tristate "Network console logging support (EXPERIMENTAL)"
Matt Mackall5e43db72005-07-27 15:24:42 -07003104 depends on EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07003105 ---help---
3106 If you want to log kernel messages over the network, enable this.
3107 See <file:Documentation/networking/netconsole.txt> for details.
3108
Satyam Sharma0bcc1812007-08-10 15:35:05 -07003109config NETCONSOLE_DYNAMIC
3110 bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
3111 depends on NETCONSOLE && SYSFS && EXPERIMENTAL
3112 select CONFIGFS_FS
3113 help
3114 This option enables the ability to dynamically reconfigure target
3115 parameters (interface, IP addresses, port numbers, MAC addresses)
3116 at runtime through a userspace interface exported using configfs.
3117 See <file:Documentation/networking/netconsole.txt> for details.
3118
Randy Dunlap54208992005-07-18 13:45:12 -07003119config NETPOLL
3120 def_bool NETCONSOLE
3121
Randy Dunlap54208992005-07-18 13:45:12 -07003122config NETPOLL_TRAP
3123 bool "Netpoll traffic trapping"
3124 default n
3125 depends on NETPOLL
3126
3127config NET_POLL_CONTROLLER
3128 def_bool NETPOLL
3129
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07003130endif # NETDEVICES