blob: a5009c8300f3364a98e8982c9697f1dee789346f [file] [log] [blame]
Paolo 'Blaisorblade' Giarrussoe4845852005-09-22 21:44:29 -07001Device-mapper snapshot support
2==============================
3
4Device-mapper allows you, without massive data copying:
5
6*) To create snapshots of any block device i.e. mountable, saved states of
7the block device which are also writable without interfering with the
8original content;
9*) To create device "forks", i.e. multiple different versions of the
10same data stream.
11
12
13In both cases, dm copies only the chunks of data that get changed and
14uses a separate copy-on-write (COW) block device for storage.
15
16
17There are two dm targets available: snapshot and snapshot-origin.
18
19*) snapshot-origin <origin>
20
21which will normally have one or more snapshots based on it.
Paolo 'Blaisorblade' Giarrussoe4845852005-09-22 21:44:29 -070022Reads will be mapped directly to the backing device. For each write, the
23original data will be saved in the <COW device> of each snapshot to keep
24its visible content unchanged, at least until the <COW device> fills up.
25
26
27*) snapshot <origin> <COW device> <persistent?> <chunksize>
28
Paolo 'Blaisorblade' Giarrusso411f1142005-11-07 01:01:01 -080029A snapshot of the <origin> block device is created. Changed chunks of
Paolo 'Blaisorblade' Giarrussoe4845852005-09-22 21:44:29 -070030<chunksize> sectors will be stored on the <COW device>. Writes will
31only go to the <COW device>. Reads will come from the <COW device> or
32from <origin> for unchanged data. <COW device> will often be
33smaller than the origin and if it fills up the snapshot will become
34useless and be disabled, returning errors. So it is important to monitor
35the amount of free space and expand the <COW device> before it fills up.
36
37<persistent?> is P (Persistent) or N (Not persistent - will not survive
38after reboot).
Paolo 'Blaisorblade' Giarrusso411f1142005-11-07 01:01:01 -080039The difference is that for transient snapshots less metadata must be
40saved on disk - they can be kept in memory by the kernel.
Paolo 'Blaisorblade' Giarrussoe4845852005-09-22 21:44:29 -070041
42
43How this is used by LVM2
44========================
45When you create the first LVM2 snapshot of a volume, four dm devices are used:
46
471) a device containing the original mapping table of the source volume;
482) a device used as the <COW device>;
493) a "snapshot" device, combining #1 and #2, which is the visible snapshot
50 volume;
514) the "original" volume (which uses the device number used by the original
52 source volume), whose table is replaced by a "snapshot-origin" mapping
53 from device #1.
54
55A fixed naming scheme is used, so with the following commands:
56
57lvcreate -L 1G -n base volumeGroup
58lvcreate -L 100M --snapshot -n snap volumeGroup/base
59
60we'll have this situation (with volumes in above order):
61
62# dmsetup table|grep volumeGroup
63
64volumeGroup-base-real: 0 2097152 linear 8:19 384
65volumeGroup-snap-cow: 0 204800 linear 8:19 2097536
66volumeGroup-snap: 0 2097152 snapshot 254:11 254:12 P 16
67volumeGroup-base: 0 2097152 snapshot-origin 254:11
68
69# ls -lL /dev/mapper/volumeGroup-*
70brw------- 1 root root 254, 11 29 ago 18:15 /dev/mapper/volumeGroup-base-real
71brw------- 1 root root 254, 12 29 ago 18:15 /dev/mapper/volumeGroup-snap-cow
72brw------- 1 root root 254, 13 29 ago 18:15 /dev/mapper/volumeGroup-snap
73brw------- 1 root root 254, 10 29 ago 18:14 /dev/mapper/volumeGroup-base
74