Blame - arch/sh/boards/Kconfig - kernel/msm-4.9

blob: 5e52d5362292b6f4db01872bcbdd08738711fd1e [file] [log] [blame]

Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	1	menu "Board support"
				2
				3	config SOLUTION_ENGINE
				4	bool
				5
Paul Mundt	704bf31	2011-01-13 18:31:25 +0900	[diff] [blame]	6	config SH_ALPHA_BOARD
				7	bool
				8
Rich Felker	7480e0a	2016-01-23 00:45:41 +0000	[diff] [blame]	9	config SH_DEVICE_TREE
				10	bool "Board Described by Device Tree"
				11	select OF
				12	select OF_EARLY_FLATTREE
				13	select CLKSRC_OF
				14	select GENERIC_CALIBRATE_DELAY
				15	help
				16	Select Board Described by Device Tree to build a kernel that
				17	does not hard-code any board-specific knowledge but instead uses
				18	a device tree blob provided by the boot-loader. You must enable
				19	drivers for any hardware you want to use separately. At this
				20	time, only boards based on the open-hardware J-Core processors
				21	have sufficient driver coverage to use this option; do not
				22	select it if you are using original SuperH hardware.
				23
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	24	config SH_SOLUTION_ENGINE
				25	bool "SolutionEngine"
				26	select SOLUTION_ENGINE
				27	select CPU_HAS_IPR_IRQ
				28	depends on CPU_SUBTYPE_SH7705 \|\| CPU_SUBTYPE_SH7709 \|\| CPU_SUBTYPE_SH7710 \|\| \
				29	CPU_SUBTYPE_SH7712 \|\| CPU_SUBTYPE_SH7750 \|\| CPU_SUBTYPE_SH7750S \|\| \
				30	CPU_SUBTYPE_SH7750R
				31	help
				32	Select SolutionEngine if configuring for a Hitachi SH7705, SH7709,
				33	SH7710, SH7712, SH7750, SH7750S or SH7750R evaluation board.
				34
				35	config SH_7206_SOLUTION_ENGINE
				36	bool "SolutionEngine7206"
				37	select SOLUTION_ENGINE
				38	depends on CPU_SUBTYPE_SH7206
				39	help
				40	Select 7206 SolutionEngine if configuring for a Hitachi SH7206
				41	evaluation board.
				42
				43	config SH_7619_SOLUTION_ENGINE
				44	bool "SolutionEngine7619"
				45	select SOLUTION_ENGINE
				46	depends on CPU_SUBTYPE_SH7619
				47	help
				48	Select 7619 SolutionEngine if configuring for a Hitachi SH7619
				49	evaluation board.
				50
				51	config SH_7721_SOLUTION_ENGINE
				52	bool "SolutionEngine7721"
				53	select SOLUTION_ENGINE
				54	depends on CPU_SUBTYPE_SH7721
				55	help
				56	Select 7721 SolutionEngine if configuring for a Hitachi SH7721
				57	evaluation board.
				58
				59	config SH_7722_SOLUTION_ENGINE
				60	bool "SolutionEngine7722"
				61	select SOLUTION_ENGINE
Paul Mundt	5df38b9	2012-05-24 18:24:32 +0900	[diff] [blame]	62	select GENERIC_IRQ_CHIP
				63	select IRQ_DOMAIN
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	64	depends on CPU_SUBTYPE_SH7722
				65	help
				66	Select 7722 SolutionEngine if configuring for a Hitachi SH772
				67	evaluation board.
				68
Kuninori Morimoto	287c129	2009-05-26 07:04:52 +0000	[diff] [blame]	69	config SH_7724_SOLUTION_ENGINE
				70	bool "SolutionEngine7724"
				71	select SOLUTION_ENGINE
				72	depends on CPU_SUBTYPE_SH7724
				73	select ARCH_REQUIRE_GPIOLIB
Kuninori Morimoto	af8a2fe	2012-04-08 21:18:28 -0700	[diff] [blame]	74	select SND_SOC_AK4642 if SND_SIMPLE_CARD
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	75	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Kuninori Morimoto	287c129	2009-05-26 07:04:52 +0000	[diff] [blame]	76	help
				77	Select 7724 SolutionEngine if configuring for a Hitachi SH7724
				78	evaluation board.
				79
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	80	config SH_7751_SOLUTION_ENGINE
				81	bool "SolutionEngine7751"
				82	select SOLUTION_ENGINE
				83	select CPU_HAS_IPR_IRQ
				84	depends on CPU_SUBTYPE_SH7751
				85	help
				86	Select 7751 SolutionEngine if configuring for a Hitachi SH7751
				87	evaluation board.
				88
				89	config SH_7780_SOLUTION_ENGINE
				90	bool "SolutionEngine7780"
				91	select SOLUTION_ENGINE
				92	select SYS_SUPPORTS_PCI
				93	depends on CPU_SUBTYPE_SH7780
				94	help
				95	Select 7780 SolutionEngine if configuring for a Renesas SH7780
				96	evaluation board.
				97
				98	config SH_7343_SOLUTION_ENGINE
				99	bool "SolutionEngine7343"
				100	select SOLUTION_ENGINE
Paul Mundt	197b58e	2012-05-24 19:07:18 +0900	[diff] [blame]	101	select GENERIC_IRQ_CHIP
				102	select IRQ_DOMAIN
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	103	depends on CPU_SUBTYPE_SH7343
				104	help
				105	Select 7343 SolutionEngine if configuring for a Hitachi
				106	SH7343 (SH-Mobile 3AS) evaluation board.
				107
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	108	config SH_HP6XX
				109	bool "HP6XX"
				110	select SYS_SUPPORTS_APM_EMULATION
				111	select HD6446X_SERIES
				112	depends on CPU_SUBTYPE_SH7709
				113	help
				114	Select HP6XX if configuring for a HP jornada HP6xx.
				115	More information (hardware only) at
				116	<http://www.hp.com/jornada/>.
				117
				118	config SH_DREAMCAST
				119	bool "Dreamcast"
				120	select SYS_SUPPORTS_PCI
				121	depends on CPU_SUBTYPE_SH7091
				122	help
				123	Select Dreamcast if configuring for a SEGA Dreamcast.
				124	More information at <http://www.linux-sh.org>
				125
				126	config SH_SH03
				127	bool "Interface CTP/PCI-SH03"
				128	depends on CPU_SUBTYPE_SH7751
				129	select CPU_HAS_IPR_IRQ
				130	select SYS_SUPPORTS_PCI
				131	help
				132	CTP/PCI-SH03 is a CPU module computer that is produced
				133	by Interface Corporation.
				134	More information at <http://www.interface.co.jp>
				135
				136	config SH_SECUREEDGE5410
				137	bool "SecureEdge5410"
				138	depends on CPU_SUBTYPE_SH7751R
				139	select CPU_HAS_IPR_IRQ
				140	select SYS_SUPPORTS_PCI
				141	help
				142	Select SecureEdge5410 if configuring for a SnapGear SH board.
				143	This includes both the OEM SecureEdge products as well as the
				144	SME product line.
				145
				146	config SH_RTS7751R2D
				147	bool "RTS7751R2D"
				148	depends on CPU_SUBTYPE_SH7751R
				149	select SYS_SUPPORTS_PCI
Magnus Damm	e6be3a2	2009-04-30 12:56:37 +0900	[diff] [blame]	150	select IO_TRAPPED if MMU
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	151	help
				152	Select RTS7751R2D if configuring for a Renesas Technology
				153	Sales SH-Graphics board.
				154
Paul Mundt	ea0aac1	2008-12-08 14:32:03 +0900	[diff] [blame]	155	config SH_RSK
				156	bool "Renesas Starter Kit"
Phil Edworthy	b6397435	2012-05-10 09:26:53 +0100	[diff] [blame]	157	depends on CPU_SUBTYPE_SH7201 \|\| CPU_SUBTYPE_SH7203 \|\| \
				158	CPU_SUBTYPE_SH7264 \|\| CPU_SUBTYPE_SH7269
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	159	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	ea0aac1	2008-12-08 14:32:03 +0900	[diff] [blame]	160	help
				161	Select this option if configuring for any of the RSK+ MCU
				162	evaluation platforms.
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	163
				164	config SH_SDK7780
				165	bool "SDK7780R3"
				166	depends on CPU_SUBTYPE_SH7780
				167	select SYS_SUPPORTS_PCI
				168	help
				169	Select SDK7780 if configuring for a Renesas SH7780 SDK7780R3
				170	evaluation board.
				171
Paul Mundt	02bf6cc	2010-01-14 20:58:58 +0900	[diff] [blame]	172	config SH_SDK7786
				173	bool "SDK7786"
				174	depends on CPU_SUBTYPE_SH7786
Paul Mundt	7dcaa8e	2010-01-15 19:13:56 +0900	[diff] [blame]	175	select SYS_SUPPORTS_PCI
Uwe Kleine-König	ce816fa	2014-04-07 15:39:19 -0700	[diff] [blame]	176	select NO_IOPORT_MAP if !PCI
Paul Mundt	47da88f	2010-10-14 03:04:44 +0900	[diff] [blame]	177	select ARCH_WANT_OPTIONAL_GPIOLIB
Paul Mundt	d8d6b90	2010-10-15 02:13:04 +0900	[diff] [blame]	178	select HAVE_SRAM_POOL
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	179	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	02bf6cc	2010-01-14 20:58:58 +0900	[diff] [blame]	180	help
				181	Select SDK7786 if configuring for a Renesas Technology Europe
				182	SH7786-65nm board.
				183
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	184	config SH_HIGHLANDER
				185	bool "Highlander"
				186	depends on CPU_SUBTYPE_SH7780 \|\| CPU_SUBTYPE_SH7785
				187	select SYS_SUPPORTS_PCI
Magnus Damm	e6be3a2	2009-04-30 12:56:37 +0900	[diff] [blame]	188	select IO_TRAPPED if MMU
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	189
Yoshihiro Shimoda	36239c6	2010-07-06 04:32:16 +0000	[diff] [blame]	190	config SH_SH7757LCR
				191	bool "SH7757LCR"
				192	depends on CPU_SUBTYPE_SH7757
				193	select ARCH_REQUIRE_GPIOLIB
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	194	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Yoshihiro Shimoda	36239c6	2010-07-06 04:32:16 +0000	[diff] [blame]	195
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	196	config SH_SH7785LCR
				197	bool "SH7785LCR"
				198	depends on CPU_SUBTYPE_SH7785
				199	select SYS_SUPPORTS_PCI
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	200
				201	config SH_SH7785LCR_29BIT_PHYSMAPS
				202	bool "SH7785LCR 29bit physmaps"
Yoshihiro Shimoda	df4d4f1	2009-03-10 15:50:44 +0900	[diff] [blame]	203	depends on SH_SH7785LCR && 29BIT
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	204	default y
				205	help
				206	This board has 2 physical memory maps. It can be changed with
				207	DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
				208	you can access all on-board device in 29bit address mode.
				209
Yoshihiro Shimoda	e79d574	2009-08-27 13:57:26 +0000	[diff] [blame]	210	config SH_SH7785LCR_PT
				211	bool "SH7785LCR prototype board on 32-bit MMU mode"
				212	depends on SH_SH7785LCR && 32BIT
				213	default n
				214	help
				215	If you use prototype board, this option is enabled.
				216
Kuninori Morimoto	5ac072e	2009-03-03 16:22:00 +0900	[diff] [blame]	217	config SH_URQUELL
				218	bool "Urquell"
				219	depends on CPU_SUBTYPE_SH7786
				220	select ARCH_REQUIRE_GPIOLIB
Paul Mundt	5713e60	2009-06-17 18:20:48 +0900	[diff] [blame]	221	select SYS_SUPPORTS_PCI
Uwe Kleine-König	ce816fa	2014-04-07 15:39:19 -0700	[diff] [blame]	222	select NO_IOPORT_MAP if !PCI
Kuninori Morimoto	5ac072e	2009-03-03 16:22:00 +0900	[diff] [blame]	223
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	224	config SH_MIGOR
				225	bool "Migo-R"
				226	depends on CPU_SUBTYPE_SH7722
Magnus Damm	69edbba	2008-12-25 18:17:34 +0900	[diff] [blame]	227	select ARCH_REQUIRE_GPIOLIB
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	228	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	229	help
				230	Select Migo-R if configuring for the SH7722 Migo-R platform
				231	by Renesas System Solutions Asia Pte. Ltd.
				232
				233	config SH_AP325RXA
				234	bool "AP-325RXA"
				235	depends on CPU_SUBTYPE_SH7723
Magnus Damm	69edbba	2008-12-25 18:17:34 +0900	[diff] [blame]	236	select ARCH_REQUIRE_GPIOLIB
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	237	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	238	help
				239	Renesas "AP-325RXA" support.
				240	Compatible with ALGO SYSTEM CO.,LTD. "AP-320A"
				241
Magnus Damm	e7d1651	2009-07-22 16:20:54 +0000	[diff] [blame]	242	config SH_KFR2R09
				243	bool "KFR2R09"
				244	depends on CPU_SUBTYPE_SH7724
				245	select ARCH_REQUIRE_GPIOLIB
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	246	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Magnus Damm	e7d1651	2009-07-22 16:20:54 +0000	[diff] [blame]	247	help
				248	"Kit For R2R for 2009" support.
				249
Kuninori Morimoto	4138b74	2009-08-19 12:08:33 +0000	[diff] [blame]	250	config SH_ECOVEC
				251	bool "EcoVec"
				252	depends on CPU_SUBTYPE_SH7724
				253	select ARCH_REQUIRE_GPIOLIB
Kuninori Morimoto	064bfad	2012-04-08 21:19:25 -0700	[diff] [blame]	254	select SND_SOC_DA7210 if SND_SIMPLE_CARD
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	255	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Kuninori Morimoto	4138b74	2009-08-19 12:08:33 +0000	[diff] [blame]	256	help
				257	Renesas "R0P7724LC0011/21RL (EcoVec)" support.
				258
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	259	config SH_SH7763RDP
				260	bool "SH7763RDP"
				261	depends on CPU_SUBTYPE_SH7763
				262	help
				263	Select SH7763RDP if configuring for a Renesas SH7763
				264	evaluation board.
				265
Nobuhiro Iwamatsu	32910e2	2009-03-17 05:54:37 +0000	[diff] [blame]	266	config SH_ESPT
				267	bool "ESPT"
				268	depends on CPU_SUBTYPE_SH7763
				269	help
				270	Select ESPT if configuring for a Renesas SH7763
				271	with gigabit ether evaluation board.
				272
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	273	config SH_EDOSK7705
				274	bool "EDOSK7705"
				275	depends on CPU_SUBTYPE_SH7705
				276
Luca Santini	3db9170	2008-09-08 12:01:15 +0900	[diff] [blame]	277	config SH_EDOSK7760
				278	bool "EDOSK7760"
				279	depends on CPU_SUBTYPE_SH7760
				280	help
				281	Select if configuring for a Renesas EDOSK7760
				282	evaluation board.
				283
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	284	config SH_SH4202_MICRODEV
				285	bool "SH4-202 MicroDev"
				286	depends on CPU_SUBTYPE_SH4_202
				287	help
				288	Select SH4-202 MicroDev if configuring for a SuperH MicroDev board
				289	with an SH4-202 CPU.
				290
				291	config SH_LANDISK
				292	bool "LANDISK"
				293	depends on CPU_SUBTYPE_SH7751R
				294	select SYS_SUPPORTS_PCI
				295	help
				296	I-O DATA DEVICE, INC. "LANDISK Series" support.
				297
				298	config SH_TITAN
				299	bool "TITAN"
				300	depends on CPU_SUBTYPE_SH7751R
				301	select CPU_HAS_IPR_IRQ
				302	select SYS_SUPPORTS_PCI
				303	help
				304	Select Titan if you are configuring for a Nimble Microsystems
				305	NetEngine NP51R.
				306
				307	config SH_SHMIN
				308	bool "SHMIN"
				309	depends on CPU_SUBTYPE_SH7706
				310	select CPU_HAS_IPR_IRQ
				311	help
				312	Select SHMIN if configuring for the SHMIN board.
				313
				314	config SH_LBOX_RE2
				315	bool "L-BOX RE2"
				316	depends on CPU_SUBTYPE_SH7751R
				317	select SYS_SUPPORTS_PCI
				318	help
				319	Select L-BOX RE2 if configuring for the NTT COMWARE L-BOX RE2.
				320
				321	config SH_X3PROTO
				322	bool "SH-X3 Prototype board"
				323	depends on CPU_SUBTYPE_SHX3
Uwe Kleine-König	ce816fa	2014-04-07 15:39:19 -0700	[diff] [blame]	324	select NO_IOPORT_MAP if !PCI
Paul Mundt	b98b358	2012-05-24 15:24:39 +0900	[diff] [blame]	325	select IRQ_DOMAIN
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	326
				327	config SH_MAGIC_PANEL_R2
				328	bool "Magic Panel R2"
				329	depends on CPU_SUBTYPE_SH7720
Paul Mundt	ae5e6d0	2009-01-07 17:16:25 +0900	[diff] [blame]	330	select ARCH_REQUIRE_GPIOLIB
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	331	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	332	help
				333	Select Magic Panel R2 if configuring for Magic Panel R2.
				334
				335	config SH_CAYMAN
				336	bool "Hitachi Cayman"
				337	depends on CPU_SUBTYPE_SH5_101 \|\| CPU_SUBTYPE_SH5_103
				338	select SYS_SUPPORTS_PCI
Mark Salter	82ef5b8	2014-01-01 11:32:52 -0800	[diff] [blame]	339	select ARCH_MIGHT_HAVE_PC_SERIO
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	340
Steve Glendinning	eaeed5d	2009-03-20 14:16:29 +0000	[diff] [blame]	341	config SH_POLARIS
				342	bool "SMSC Polaris"
				343	select CPU_HAS_IPR_IRQ
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	344	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Steve Glendinning	eaeed5d	2009-03-20 14:16:29 +0000	[diff] [blame]	345	depends on CPU_SUBTYPE_SH7709
				346	help
				347	Select if configuring for an SMSC Polaris development board
				348
Hitoshi Mitake	3a59826	2010-06-21 15:10:51 +0900	[diff] [blame]	349	config SH_SH2007
				350	bool "SH-2007 board"
Uwe Kleine-König	ce816fa	2014-04-07 15:39:19 -0700	[diff] [blame]	351	select NO_IOPORT_MAP
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	352	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Hitoshi Mitake	3a59826	2010-06-21 15:10:51 +0900	[diff] [blame]	353	depends on CPU_SUBTYPE_SH7780
				354	help
				355	SH-2007 is a single-board computer based around SH7780 chip
				356	intended for embedded applications.
				357	It has an Ethernet interface (SMC9118), direct connected
				358	Compact Flash socket, two serial ports and PC-104 bus.
				359	More information at <http://sh2000.sh-linux.org>.
				360
Paul Mundt	bc34b08	2011-01-13 18:32:42 +0900	[diff] [blame]	361	config SH_APSH4A3A
				362	bool "AP-SH4A-3A"
				363	select SH_ALPHA_BOARD
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	364	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	bc34b08	2011-01-13 18:32:42 +0900	[diff] [blame]	365	depends on CPU_SUBTYPE_SH7785
				366	help
				367	Select AP-SH4A-3A if configuring for an ALPHAPROJECT AP-SH4A-3A.
				368
Paul Mundt	8a453ca	2011-01-13 18:36:21 +0900	[diff] [blame]	369	config SH_APSH4AD0A
				370	bool "AP-SH4AD-0A"
				371	select SH_ALPHA_BOARD
				372	select SYS_SUPPORTS_PCI
Guennadi Liakhovetski	89d7148	2012-07-05 15:18:50 +0200	[diff] [blame]	373	select REGULATOR_FIXED_VOLTAGE if REGULATOR
Paul Mundt	8a453ca	2011-01-13 18:36:21 +0900	[diff] [blame]	374	depends on CPU_SUBTYPE_SH7786
				375	help
				376	Select AP-SH4AD-0A if configuring for an ALPHAPROJECT AP-SH4AD-0A.
				377
Paul Mundt	939a24a	2008-07-29 21:41:37 +0900	[diff] [blame]	378	source "arch/sh/boards/mach-r2d/Kconfig"
				379	source "arch/sh/boards/mach-highlander/Kconfig"
				380	source "arch/sh/boards/mach-sdk7780/Kconfig"
				381	source "arch/sh/boards/mach-migor/Kconfig"
Paul Mundt	ea0aac1	2008-12-08 14:32:03 +0900	[diff] [blame]	382	source "arch/sh/boards/mach-rsk/Kconfig"
Paul Mundt	c8b5d9d	2008-07-30 00:13:39 +0900	[diff] [blame]	383
				384	if SH_MAGIC_PANEL_R2
				385
				386	menu "Magic Panel R2 options"
				387
				388	config SH_MAGIC_PANEL_R2_VERSION
Paul Bolle	e70cfe4	2014-06-11 12:03:49 +0200	[diff] [blame]	389	int "Magic Panel R2 Version"
Paul Mundt	c8b5d9d	2008-07-30 00:13:39 +0900	[diff] [blame]	390	default "3"
				391	help
				392	Set the version of the Magic Panel R2
				393
				394	endmenu
				395
				396	endif
Stuart Menefy	9e7f60a	2012-04-19 17:29:38 +0900	[diff] [blame]	397
				398	endmenu