Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame^] | 1 | #include <linux/kernel.h> |
| 2 | #include <linux/init.h> |
| 3 | #include <linux/types.h> |
| 4 | #include <linux/pci.h> |
| 5 | |
| 6 | #include <asm/debug.h> |
| 7 | |
| 8 | #include <asm/ddb5xxx/ddb5xxx.h> |
| 9 | |
| 10 | static struct resource extpci_io_resource = { |
| 11 | "pci IO space", |
| 12 | 0x1000, /* leave some room for ISA bus */ |
| 13 | DDB_PCI_IO_SIZE - 1, |
| 14 | IORESOURCE_IO |
| 15 | }; |
| 16 | |
| 17 | static struct resource extpci_mem_resource = { |
| 18 | "pci memory space", |
| 19 | DDB_PCI_MEM_BASE + 0x00100000, /* leave 1 MB for RTC */ |
| 20 | DDB_PCI_MEM_BASE + DDB_PCI_MEM_SIZE - 1, |
| 21 | IORESOURCE_MEM |
| 22 | }; |
| 23 | |
| 24 | extern struct pci_ops ddb5476_ext_pci_ops; |
| 25 | |
| 26 | struct pci_controller ddb5476_controller = { |
| 27 | .pci_ops = &ddb5476_ext_pci_ops, |
| 28 | .io_resource = &extpci_io_resource, |
| 29 | .mem_resource = &extpci_mem_resource |
| 30 | }; |
| 31 | |
| 32 | |
| 33 | /* |
| 34 | * we fix up irqs based on the slot number. |
| 35 | * The first entry is at AD:11. |
| 36 | * |
| 37 | * This does not work for devices on sub-buses yet. |
| 38 | */ |
| 39 | |
| 40 | /* |
| 41 | * temporary |
| 42 | */ |
| 43 | |
| 44 | #define PCI_EXT_INTA 8 |
| 45 | #define PCI_EXT_INTB 9 |
| 46 | #define PCI_EXT_INTC 10 |
| 47 | #define PCI_EXT_INTD 11 |
| 48 | #define PCI_EXT_INTE 12 |
| 49 | |
| 50 | /* |
| 51 | * based on ddb5477 manual page 11 |
| 52 | */ |
| 53 | #define MAX_SLOT_NUM 21 |
| 54 | static unsigned char irq_map[MAX_SLOT_NUM] = { |
| 55 | [ 2] = 9, /* AD:13 USB */ |
| 56 | [ 3] = 10, /* AD:14 PMU */ |
| 57 | [ 5] = 0, /* AD:16 P2P bridge */ |
| 58 | [ 6] = nile4_to_irq(PCI_EXT_INTB), /* AD:17 */ |
| 59 | [ 7] = nile4_to_irq(PCI_EXT_INTC), /* AD:18 */ |
| 60 | [ 8] = nile4_to_irq(PCI_EXT_INTD), /* AD:19 */ |
| 61 | [ 9] = nile4_to_irq(PCI_EXT_INTA), /* AD:20 */ |
| 62 | [13] = 14, /* AD:24 HD controller, M5229 */ |
| 63 | }; |
| 64 | |
| 65 | int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin) |
| 66 | { |
| 67 | return irq_map[slot]; |
| 68 | } |
| 69 | |
| 70 | /* Do platform specific device initialization at pci_enable_device() time */ |
| 71 | int pcibios_plat_dev_init(struct pci_dev *dev) |
| 72 | { |
| 73 | return 0; |
| 74 | } |
| 75 | |
| 76 | void __init ddb_pci_reset_bus(void) |
| 77 | { |
| 78 | u32 temp; |
| 79 | |
| 80 | /* |
| 81 | * I am not sure about the "official" procedure, the following |
| 82 | * steps work as far as I know: |
| 83 | * We first set PCI cold reset bit (bit 31) in PCICTRL-H. |
| 84 | * Then we clear the PCI warm reset bit (bit 30) to 0 in PCICTRL-H. |
| 85 | * The same is true for both PCI channels. |
| 86 | */ |
| 87 | temp = ddb_in32(DDB_PCICTRL + 4); |
| 88 | temp |= 0x80000000; |
| 89 | ddb_out32(DDB_PCICTRL + 4, temp); |
| 90 | temp &= ~0xc0000000; |
| 91 | ddb_out32(DDB_PCICTRL + 4, temp); |
| 92 | |
| 93 | } |