Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame^] | 1 | /* |
| 2 | * sgiseeq.h: Defines for the Seeq8003 ethernet controller. |
| 3 | * |
| 4 | * Copyright (C) 1996 David S. Miller (dm@engr.sgi.com) |
| 5 | */ |
| 6 | #ifndef _SGISEEQ_H |
| 7 | #define _SGISEEQ_H |
| 8 | |
| 9 | struct sgiseeq_wregs { |
| 10 | volatile unsigned int multicase_high[2]; |
| 11 | volatile unsigned int frame_gap; |
| 12 | volatile unsigned int control; |
| 13 | }; |
| 14 | |
| 15 | struct sgiseeq_rregs { |
| 16 | volatile unsigned int collision_tx[2]; |
| 17 | volatile unsigned int collision_all[2]; |
| 18 | volatile unsigned int _unused0; |
| 19 | volatile unsigned int rflags; |
| 20 | }; |
| 21 | |
| 22 | struct sgiseeq_regs { |
| 23 | union { |
| 24 | volatile unsigned int eth_addr[6]; |
| 25 | volatile unsigned int multicast_low[6]; |
| 26 | struct sgiseeq_wregs wregs; |
| 27 | struct sgiseeq_rregs rregs; |
| 28 | } rw; |
| 29 | volatile unsigned int rstat; |
| 30 | volatile unsigned int tstat; |
| 31 | }; |
| 32 | |
| 33 | /* Seeq8003 receive status register */ |
| 34 | #define SEEQ_RSTAT_OVERF 0x001 /* Overflow */ |
| 35 | #define SEEQ_RSTAT_CERROR 0x002 /* CRC error */ |
| 36 | #define SEEQ_RSTAT_DERROR 0x004 /* Dribble error */ |
| 37 | #define SEEQ_RSTAT_SFRAME 0x008 /* Short frame */ |
| 38 | #define SEEQ_RSTAT_REOF 0x010 /* Received end of frame */ |
| 39 | #define SEEQ_RSTAT_FIG 0x020 /* Frame is good */ |
| 40 | #define SEEQ_RSTAT_TIMEO 0x040 /* Timeout, or late receive */ |
| 41 | #define SEEQ_RSTAT_WHICH 0x080 /* Which status, 1=old 0=new */ |
| 42 | #define SEEQ_RSTAT_LITTLE 0x100 /* DMA is done in little endian format */ |
| 43 | #define SEEQ_RSTAT_SDMA 0x200 /* DMA has started */ |
| 44 | #define SEEQ_RSTAT_ADMA 0x400 /* DMA is active */ |
| 45 | #define SEEQ_RSTAT_ROVERF 0x800 /* Receive buffer overflow */ |
| 46 | |
| 47 | /* Seeq8003 receive command register */ |
| 48 | #define SEEQ_RCMD_RDISAB 0x000 /* Disable receiver on the Seeq8003 */ |
| 49 | #define SEEQ_RCMD_IOVERF 0x001 /* IRQ on buffer overflows */ |
| 50 | #define SEEQ_RCMD_ICRC 0x002 /* IRQ on CRC errors */ |
| 51 | #define SEEQ_RCMD_IDRIB 0x004 /* IRQ on dribble errors */ |
| 52 | #define SEEQ_RCMD_ISHORT 0x008 /* IRQ on short frames */ |
| 53 | #define SEEQ_RCMD_IEOF 0x010 /* IRQ on end of frame */ |
| 54 | #define SEEQ_RCMD_IGOOD 0x020 /* IRQ on good frames */ |
| 55 | #define SEEQ_RCMD_RANY 0x040 /* Receive any frame */ |
| 56 | #define SEEQ_RCMD_RBCAST 0x080 /* Receive broadcasts */ |
| 57 | #define SEEQ_RCMD_RBMCAST 0x0c0 /* Receive broadcasts/multicasts */ |
| 58 | |
| 59 | /* Seeq8003 transmit status register */ |
| 60 | #define SEEQ_TSTAT_UFLOW 0x001 /* Transmit buffer underflow */ |
| 61 | #define SEEQ_TSTAT_CLS 0x002 /* Collision detected */ |
| 62 | #define SEEQ_TSTAT_R16 0x004 /* Did 16 retries to tx a frame */ |
| 63 | #define SEEQ_TSTAT_PTRANS 0x008 /* Packet was transmitted ok */ |
| 64 | #define SEEQ_TSTAT_LCLS 0x010 /* Late collision occurred */ |
| 65 | #define SEEQ_TSTAT_WHICH 0x080 /* Which status, 1=old 0=new */ |
| 66 | #define SEEQ_TSTAT_TLE 0x100 /* DMA is done in little endian format */ |
| 67 | #define SEEQ_TSTAT_SDMA 0x200 /* DMA has started */ |
| 68 | #define SEEQ_TSTAT_ADMA 0x400 /* DMA is active */ |
| 69 | |
| 70 | /* Seeq8003 transmit command register */ |
| 71 | #define SEEQ_TCMD_RB0 0x00 /* Register bank zero w/station addr */ |
| 72 | #define SEEQ_TCMD_IUF 0x01 /* IRQ on tx underflow */ |
| 73 | #define SEEQ_TCMD_IC 0x02 /* IRQ on collisions */ |
| 74 | #define SEEQ_TCMD_I16 0x04 /* IRQ after 16 failed attempts to tx frame */ |
| 75 | #define SEEQ_TCMD_IPT 0x08 /* IRQ when packet successfully transmitted */ |
| 76 | #define SEEQ_TCMD_RB1 0x20 /* Register bank one w/multi-cast low byte */ |
| 77 | #define SEEQ_TCMD_RB2 0x40 /* Register bank two w/multi-cast high byte */ |
| 78 | |
| 79 | /* Seeq8003 control register */ |
| 80 | #define SEEQ_CTRL_XCNT 0x01 |
| 81 | #define SEEQ_CTRL_ACCNT 0x02 |
| 82 | #define SEEQ_CTRL_SFLAG 0x04 |
| 83 | #define SEEQ_CTRL_EMULTI 0x08 |
| 84 | #define SEEQ_CTRL_ESHORT 0x10 |
| 85 | #define SEEQ_CTRL_ENCARR 0x20 |
| 86 | |
| 87 | /* Seeq8003 control registers on the SGI Hollywood HPC. */ |
| 88 | #define SEEQ_HPIO_P1BITS 0x00000001 /* cycles to stay in P1 phase for PIO */ |
| 89 | #define SEEQ_HPIO_P2BITS 0x00000060 /* cycles to stay in P2 phase for PIO */ |
| 90 | #define SEEQ_HPIO_P3BITS 0x00000100 /* cycles to stay in P3 phase for PIO */ |
| 91 | #define SEEQ_HDMA_D1BITS 0x00000006 /* cycles to stay in D1 phase for DMA */ |
| 92 | #define SEEQ_HDMA_D2BITS 0x00000020 /* cycles to stay in D2 phase for DMA */ |
| 93 | #define SEEQ_HDMA_D3BITS 0x00000000 /* cycles to stay in D3 phase for DMA */ |
| 94 | #define SEEQ_HDMA_TIMEO 0x00030000 /* cycles for DMA timeout */ |
| 95 | #define SEEQ_HCTL_NORM 0x00000000 /* Normal operation mode */ |
| 96 | #define SEEQ_HCTL_RESET 0x00000001 /* Reset Seeq8003 and HPC interface */ |
| 97 | #define SEEQ_HCTL_IPEND 0x00000002 /* IRQ is pending for the chip */ |
| 98 | #define SEEQ_HCTL_IPG 0x00001000 /* Inter-packet gap */ |
| 99 | #define SEEQ_HCTL_RFIX 0x00002000 /* At rxdc, clear end-of-packet */ |
| 100 | #define SEEQ_HCTL_EFIX 0x00004000 /* fixes intr status bit settings */ |
| 101 | #define SEEQ_HCTL_IFIX 0x00008000 /* enable startup timeouts */ |
| 102 | |
| 103 | #endif /* !(_SGISEEQ_H) */ |