blob: 8c9e874c9118c494a74a42979e45c1c8f68030c0 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* hermes.h
2 *
3 * Driver core for the "Hermes" wireless MAC controller, as used in
4 * the Lucent Orinoco and Cabletron RoamAbout cards. It should also
5 * work on the hfa3841 and hfa3842 MAC controller chips used in the
6 * Prism I & II chipsets.
7 *
8 * This is not a complete driver, just low-level access routines for
9 * the MAC controller itself.
10 *
11 * Based on the prism2 driver from Absolute Value Systems' linux-wlan
12 * project, the Linux wvlan_cs driver, Lucent's HCF-Light
13 * (wvlan_hcf.c) library, and the NetBSD wireless driver.
14 *
15 * Copyright (C) 2000, David Gibson, Linuxcare Australia.
16 * (C) Copyright David Gibson, IBM Corp. 2001-2003.
17 *
18 * Portions taken from hfa384x.h, Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved.
19 *
20 * This file distributed under the GPL, version 2.
21 */
22
23#ifndef _HERMES_H
24#define _HERMES_H
25
26/* Notes on locking:
27 *
28 * As a module of low level hardware access routines, there is no
29 * locking. Users of this module should ensure that they serialize
30 * access to the hermes_t structure, and to the hardware
31*/
32
33#include <linux/delay.h>
34#include <linux/if_ether.h>
35#include <asm/byteorder.h>
36
37/*
38 * Limits and constants
39 */
40#define HERMES_ALLOC_LEN_MIN (4)
41#define HERMES_ALLOC_LEN_MAX (2400)
42#define HERMES_LTV_LEN_MAX (34)
43#define HERMES_BAP_DATALEN_MAX (4096)
44#define HERMES_BAP_OFFSET_MAX (4096)
45#define HERMES_PORTID_MAX (7)
46#define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1)
47#define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */
48#define HERMES_PDA_RECS_MAX (200) /* a guess */
49#define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */
50#define HERMES_SCANRESULT_MAX (35)
51#define HERMES_CHINFORESULT_MAX (8)
52#define HERMES_MAX_MULTICAST (16)
53#define HERMES_MAGIC (0x7d1f)
54
55/*
56 * Hermes register offsets
57 */
58#define HERMES_CMD (0x00)
59#define HERMES_PARAM0 (0x02)
60#define HERMES_PARAM1 (0x04)
61#define HERMES_PARAM2 (0x06)
62#define HERMES_STATUS (0x08)
63#define HERMES_RESP0 (0x0A)
64#define HERMES_RESP1 (0x0C)
65#define HERMES_RESP2 (0x0E)
66#define HERMES_INFOFID (0x10)
67#define HERMES_RXFID (0x20)
68#define HERMES_ALLOCFID (0x22)
69#define HERMES_TXCOMPLFID (0x24)
70#define HERMES_SELECT0 (0x18)
71#define HERMES_OFFSET0 (0x1C)
72#define HERMES_DATA0 (0x36)
73#define HERMES_SELECT1 (0x1A)
74#define HERMES_OFFSET1 (0x1E)
75#define HERMES_DATA1 (0x38)
76#define HERMES_EVSTAT (0x30)
77#define HERMES_INTEN (0x32)
78#define HERMES_EVACK (0x34)
79#define HERMES_CONTROL (0x14)
80#define HERMES_SWSUPPORT0 (0x28)
81#define HERMES_SWSUPPORT1 (0x2A)
82#define HERMES_SWSUPPORT2 (0x2C)
83#define HERMES_AUXPAGE (0x3A)
84#define HERMES_AUXOFFSET (0x3C)
85#define HERMES_AUXDATA (0x3E)
86
87/*
88 * CMD register bitmasks
89 */
90#define HERMES_CMD_BUSY (0x8000)
91#define HERMES_CMD_AINFO (0x7f00)
92#define HERMES_CMD_MACPORT (0x0700)
93#define HERMES_CMD_RECL (0x0100)
94#define HERMES_CMD_WRITE (0x0100)
95#define HERMES_CMD_PROGMODE (0x0300)
96#define HERMES_CMD_CMDCODE (0x003f)
97
98/*
99 * STATUS register bitmasks
100 */
101#define HERMES_STATUS_RESULT (0x7f00)
102#define HERMES_STATUS_CMDCODE (0x003f)
103
104/*
105 * OFFSET register bitmasks
106 */
107#define HERMES_OFFSET_BUSY (0x8000)
108#define HERMES_OFFSET_ERR (0x4000)
109#define HERMES_OFFSET_DATAOFF (0x0ffe)
110
111/*
112 * Event register bitmasks (INTEN, EVSTAT, EVACK)
113 */
114#define HERMES_EV_TICK (0x8000)
115#define HERMES_EV_WTERR (0x4000)
116#define HERMES_EV_INFDROP (0x2000)
117#define HERMES_EV_INFO (0x0080)
118#define HERMES_EV_DTIM (0x0020)
119#define HERMES_EV_CMD (0x0010)
120#define HERMES_EV_ALLOC (0x0008)
121#define HERMES_EV_TXEXC (0x0004)
122#define HERMES_EV_TX (0x0002)
123#define HERMES_EV_RX (0x0001)
124
125/*
126 * Command codes
127 */
128/*--- Controller Commands ----------------------------*/
129#define HERMES_CMD_INIT (0x0000)
130#define HERMES_CMD_ENABLE (0x0001)
131#define HERMES_CMD_DISABLE (0x0002)
132#define HERMES_CMD_DIAG (0x0003)
133
134/*--- Buffer Mgmt Commands ---------------------------*/
135#define HERMES_CMD_ALLOC (0x000A)
136#define HERMES_CMD_TX (0x000B)
137
138/*--- Regulate Commands ------------------------------*/
139#define HERMES_CMD_NOTIFY (0x0010)
140#define HERMES_CMD_INQUIRE (0x0011)
141
142/*--- Configure Commands -----------------------------*/
143#define HERMES_CMD_ACCESS (0x0021)
144#define HERMES_CMD_DOWNLD (0x0022)
145
146/*--- Serial I/O Commands ----------------------------*/
147#define HERMES_CMD_READMIF (0x0030)
148#define HERMES_CMD_WRITEMIF (0x0031)
149
150/*--- Debugging Commands -----------------------------*/
151#define HERMES_CMD_TEST (0x0038)
152
153
154/* Test command arguments */
155#define HERMES_TEST_SET_CHANNEL 0x0800
156#define HERMES_TEST_MONITOR 0x0b00
157#define HERMES_TEST_STOP 0x0f00
158
159/* Authentication algorithms */
160#define HERMES_AUTH_OPEN 1
161#define HERMES_AUTH_SHARED_KEY 2
162
163/* WEP settings */
164#define HERMES_WEP_PRIVACY_INVOKED 0x0001
165#define HERMES_WEP_EXCL_UNENCRYPTED 0x0002
166#define HERMES_WEP_HOST_ENCRYPT 0x0010
167#define HERMES_WEP_HOST_DECRYPT 0x0080
168
169/* Symbol hostscan options */
170#define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001
171#define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002
172#define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040
173#define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080
174
175/*
176 * Frame structures and constants
177 */
178
179#define HERMES_DESCRIPTOR_OFFSET 0
180#define HERMES_802_11_OFFSET (14)
181#define HERMES_802_3_OFFSET (14+32)
182#define HERMES_802_2_OFFSET (14+32+14)
183
184#define HERMES_RXSTAT_ERR (0x0003)
185#define HERMES_RXSTAT_BADCRC (0x0001)
186#define HERMES_RXSTAT_UNDECRYPTABLE (0x0002)
187#define HERMES_RXSTAT_MACPORT (0x0700)
188#define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */
189#define HERMES_RXSTAT_MSGTYPE (0xE000)
190#define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */
191#define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */
192#define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */
193
194struct hermes_tx_descriptor {
195 u16 status;
196 u16 reserved1;
197 u16 reserved2;
198 u32 sw_support;
199 u8 retry_count;
200 u8 tx_rate;
201 u16 tx_control;
202} __attribute__ ((packed));
203
204#define HERMES_TXSTAT_RETRYERR (0x0001)
205#define HERMES_TXSTAT_AGEDERR (0x0002)
206#define HERMES_TXSTAT_DISCON (0x0004)
207#define HERMES_TXSTAT_FORMERR (0x0008)
208
209#define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */
210#define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */
211#define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */
212#define HERMES_TXCTRL_ALT_RTRY (0x0020)
213
214/* Inquiry constants and data types */
215
216#define HERMES_INQ_TALLIES (0xF100)
217#define HERMES_INQ_SCAN (0xF101)
218#define HERMES_INQ_CHANNELINFO (0xF102)
219#define HERMES_INQ_HOSTSCAN (0xF103)
220#define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104)
221#define HERMES_INQ_LINKSTATUS (0xF200)
222#define HERMES_INQ_SEC_STAT_AGERE (0xF202)
223
224struct hermes_tallies_frame {
225 u16 TxUnicastFrames;
226 u16 TxMulticastFrames;
227 u16 TxFragments;
228 u16 TxUnicastOctets;
229 u16 TxMulticastOctets;
230 u16 TxDeferredTransmissions;
231 u16 TxSingleRetryFrames;
232 u16 TxMultipleRetryFrames;
233 u16 TxRetryLimitExceeded;
234 u16 TxDiscards;
235 u16 RxUnicastFrames;
236 u16 RxMulticastFrames;
237 u16 RxFragments;
238 u16 RxUnicastOctets;
239 u16 RxMulticastOctets;
240 u16 RxFCSErrors;
241 u16 RxDiscards_NoBuffer;
242 u16 TxDiscardsWrongSA;
243 u16 RxWEPUndecryptable;
244 u16 RxMsgInMsgFragments;
245 u16 RxMsgInBadMsgFragments;
246 /* Those last are probably not available in very old firmwares */
247 u16 RxDiscards_WEPICVError;
248 u16 RxDiscards_WEPExcluded;
249} __attribute__ ((packed));
250
251/* Grabbed from wlan-ng - Thanks Mark... - Jean II
252 * This is the result of a scan inquiry command */
253/* Structure describing info about an Access Point */
254struct prism2_scan_apinfo {
255 u16 channel; /* Channel where the AP sits */
256 u16 noise; /* Noise level */
257 u16 level; /* Signal level */
258 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
259 u16 beacon_interv; /* Beacon interval */
260 u16 capabilities; /* Capabilities */
261 u16 essid_len; /* ESSID length */
262 u8 essid[32]; /* ESSID of the network */
263 u8 rates[10]; /* Bit rate supported */
264 u16 proberesp_rate; /* Data rate of the response frame */
265 u16 atim; /* ATIM window time, Kus (hostscan only) */
266} __attribute__ ((packed));
267
268/* Same stuff for the Lucent/Agere card.
269 * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */
270struct agere_scan_apinfo {
271 u16 channel; /* Channel where the AP sits */
272 u16 noise; /* Noise level */
273 u16 level; /* Signal level */
274 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
275 u16 beacon_interv; /* Beacon interval */
276 u16 capabilities; /* Capabilities */
277 /* bits: 0-ess, 1-ibss, 4-privacy [wep] */
278 u16 essid_len; /* ESSID length */
279 u8 essid[32]; /* ESSID of the network */
280} __attribute__ ((packed));
281
282/* Moustafa: Scan structure for Symbol cards */
283struct symbol_scan_apinfo {
284 u8 channel; /* Channel where the AP sits */
285 u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */
286 u16 noise; /* Noise level */
287 u16 level; /* Signal level */
288 u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */
289 u16 beacon_interv; /* Beacon interval */
290 u16 capabilities; /* Capabilities */
291 /* bits: 0-ess, 1-ibss, 4-privacy [wep] */
292 u16 essid_len; /* ESSID length */
293 u8 essid[32]; /* ESSID of the network */
294 u16 rates[5]; /* Bit rate supported */
295 u16 basic_rates; /* Basic rates bitmask */
296 u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */
297 u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */
298} __attribute__ ((packed));
299
300union hermes_scan_info {
301 struct agere_scan_apinfo a;
302 struct prism2_scan_apinfo p;
303 struct symbol_scan_apinfo s;
304};
305
306#define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000)
307#define HERMES_LINKSTATUS_CONNECTED (0x0001)
308#define HERMES_LINKSTATUS_DISCONNECTED (0x0002)
309#define HERMES_LINKSTATUS_AP_CHANGE (0x0003)
310#define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004)
311#define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005)
312#define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006)
313
314struct hermes_linkstatus {
315 u16 linkstatus; /* Link status */
316} __attribute__ ((packed));
317
318struct hermes_response {
319 u16 status, resp0, resp1, resp2;
320};
321
322/* "ID" structure - used for ESSID and station nickname */
323struct hermes_idstring {
324 u16 len;
325 u16 val[16];
326} __attribute__ ((packed));
327
328struct hermes_multicast {
329 u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN];
330} __attribute__ ((packed));
331
332// #define HERMES_DEBUG_BUFFER 1
333#define HERMES_DEBUG_BUFSIZE 4096
334struct hermes_debug_entry {
335 int bap;
336 u16 id, offset;
337 int cycles;
338};
339
340#ifdef __KERNEL__
341
342/* Timeouts */
343#define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */
344
345/* Basic control structure */
346typedef struct hermes {
347 void __iomem *iobase;
348 int reg_spacing;
349#define HERMES_16BIT_REGSPACING 0
350#define HERMES_32BIT_REGSPACING 1
351
352 u16 inten; /* Which interrupts should be enabled? */
353
354#ifdef HERMES_DEBUG_BUFFER
355 struct hermes_debug_entry dbuf[HERMES_DEBUG_BUFSIZE];
356 unsigned long dbufp;
357 unsigned long profile[HERMES_BAP_BUSY_TIMEOUT+1];
358#endif
359} hermes_t;
360
361/* Register access convenience macros */
362#define hermes_read_reg(hw, off) \
363 (ioread16((hw)->iobase + ( (off) << (hw)->reg_spacing )))
364#define hermes_write_reg(hw, off, val) \
365 (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing)))
366#define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name)
367#define hermes_write_regn(hw, name, val) hermes_write_reg((hw), HERMES_##name, (val))
368
369/* Function prototypes */
370void hermes_struct_init(hermes_t *hw, void __iomem *address, int reg_spacing);
371int hermes_init(hermes_t *hw);
372int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0,
373 struct hermes_response *resp);
374int hermes_allocate(hermes_t *hw, u16 size, u16 *fid);
375
376int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len,
377 u16 id, u16 offset);
378int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, unsigned len,
379 u16 id, u16 offset);
380int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned buflen,
381 u16 *length, void *buf);
382int hermes_write_ltv(hermes_t *hw, int bap, u16 rid,
383 u16 length, const void *value);
384
385/* Inline functions */
386
387static inline int hermes_present(hermes_t *hw)
388{
389 return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC;
390}
391
392static inline void hermes_set_irqmask(hermes_t *hw, u16 events)
393{
394 hw->inten = events;
395 hermes_write_regn(hw, INTEN, events);
396}
397
398static inline int hermes_enable_port(hermes_t *hw, int port)
399{
400 return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8),
401 0, NULL);
402}
403
404static inline int hermes_disable_port(hermes_t *hw, int port)
405{
406 return hermes_docmd_wait(hw, HERMES_CMD_DISABLE | (port << 8),
407 0, NULL);
408}
409
410/* Initiate an INQUIRE command (tallies or scan). The result will come as an
411 * information frame in __orinoco_ev_info() */
412static inline int hermes_inquire(hermes_t *hw, u16 rid)
413{
414 return hermes_docmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL);
415}
416
417#define HERMES_BYTES_TO_RECLEN(n) ( (((n)+1)/2) + 1 )
418#define HERMES_RECLEN_TO_BYTES(n) ( ((n)-1) * 2 )
419
420/* Note that for the next two, the count is in 16-bit words, not bytes */
421static inline void hermes_read_words(struct hermes *hw, int off, void *buf, unsigned count)
422{
423 off = off << hw->reg_spacing;
424 ioread16_rep(hw->iobase + off, buf, count);
425}
426
427static inline void hermes_write_words(struct hermes *hw, int off, const void *buf, unsigned count)
428{
429 off = off << hw->reg_spacing;
430 iowrite16_rep(hw->iobase + off, buf, count);
431}
432
433static inline void hermes_clear_words(struct hermes *hw, int off, unsigned count)
434{
435 unsigned i;
436
437 off = off << hw->reg_spacing;
438
439 for (i = 0; i < count; i++)
440 iowrite16(0, hw->iobase + off);
441}
442
443#define HERMES_READ_RECORD(hw, bap, rid, buf) \
444 (hermes_read_ltv((hw),(bap),(rid), sizeof(*buf), NULL, (buf)))
445#define HERMES_WRITE_RECORD(hw, bap, rid, buf) \
446 (hermes_write_ltv((hw),(bap),(rid),HERMES_BYTES_TO_RECLEN(sizeof(*buf)),(buf)))
447
448static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word)
449{
450 u16 rec;
451 int err;
452
453 err = HERMES_READ_RECORD(hw, bap, rid, &rec);
454 *word = le16_to_cpu(rec);
455 return err;
456}
457
458static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word)
459{
460 u16 rec = cpu_to_le16(word);
461 return HERMES_WRITE_RECORD(hw, bap, rid, &rec);
462}
463
464#else /* ! __KERNEL__ */
465
466/* These are provided for the benefit of userspace drivers and testing programs
467 which use ioperm() or iopl() */
468
469#define hermes_read_reg(base, off) (inw((base) + (off)))
470#define hermes_write_reg(base, off, val) (outw((val), (base) + (off)))
471
472#define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name))
473#define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val)))
474
475/* Note that for the next two, the count is in 16-bit words, not bytes */
476#define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count)))
477#define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count)))
478
479#endif /* ! __KERNEL__ */
480
481#endif /* _HERMES_H */