blob: 6dc2897672a127822954853dfb32a792ce7a039f [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#define AUTOSENSE
2#define PSEUDO_DMA
3
4/*
5 * Trantor T128/T128F/T228 driver
6 * Note : architecturally, the T100 and T130 are different and won't
7 * work
8 *
9 * Copyright 1993, Drew Eckhardt
10 * Visionary Computing
11 * (Unix and Linux consulting and custom programming)
12 * drew@colorado.edu
13 * +1 (303) 440-4894
14 *
15 * DISTRIBUTION RELEASE 3.
16 *
17 * For more information, please consult
18 *
19 * Trantor Systems, Ltd.
20 * T128/T128F/T228 SCSI Host Adapter
21 * Hardware Specifications
22 *
23 * Trantor Systems, Ltd.
24 * 5415 Randall Place
25 * Fremont, CA 94538
26 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910
27 *
28 * and
29 *
30 * NCR 5380 Family
31 * SCSI Protocol Controller
32 * Databook
33 *
34 * NCR Microelectronics
35 * 1635 Aeroplaza Drive
36 * Colorado Springs, CO 80916
37 * 1+ (719) 578-3400
38 * 1+ (800) 334-5454
39 */
40
41/*
42 * Options :
43 * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
44 * for commands that return with a CHECK CONDITION status.
45 *
46 * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
47 * increase compared to polled I/O.
48 *
49 * PARITY - enable parity checking. Not supported.
50 *
51 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
52 *
53 *
54 * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. You
55 * only really want to use this if you're having a problem with
56 * dropped characters during high speed communications, and even
57 * then, you're going to be better off twiddling with transfersize.
58 *
59 * USLEEP - enable support for devices that don't disconnect. Untested.
60 *
61 * The card is detected and initialized in one of several ways :
62 * 1. Autoprobe (default) - since the board is memory mapped,
63 * a BIOS signature is scanned for to locate the registers.
64 * An interrupt is triggered to autoprobe for the interrupt
65 * line.
66 *
67 * 2. With command line overrides - t128=address,irq may be
68 * used on the LILO command line to override the defaults.
69 *
70 * 3. With the T128_OVERRIDE compile time define. This is
71 * specified as an array of address, irq tuples. Ie, for
72 * one board at the default 0xcc000 address, IRQ5, I could say
73 * -DT128_OVERRIDE={{0xcc000, 5}}
74 *
75 * Note that if the override methods are used, place holders must
76 * be specified for other boards in the system.
77 *
78 * T128/T128F jumper/dipswitch settings (note : on my sample, the switches
79 * were epoxy'd shut, meaning I couldn't change the 0xcc000 base address) :
80 *
81 * T128 Sw7 Sw8 Sw6 = 0ws Sw5 = boot
82 * T128F Sw6 Sw7 Sw5 = 0ws Sw4 = boot Sw8 = floppy disable
83 * cc000 off off
84 * c8000 off on
85 * dc000 on off
86 * d8000 on on
87 *
88 *
89 * Interrupts
90 * There is a 12 pin jumper block, jp1, numbered as follows :
91 * T128 (JP1) T128F (J5)
92 * 2 4 6 8 10 12 11 9 7 5 3 1
93 * 1 3 5 7 9 11 12 10 8 6 4 2
94 *
95 * 3 2-4
96 * 5 1-3
97 * 7 3-5
98 * T128F only
99 * 10 8-10
100 * 12 7-9
101 * 14 10-12
102 * 15 9-11
103 */
104
105/*
106 * $Log: t128.c,v $
107 */
108
109#include <asm/system.h>
110#include <linux/signal.h>
111#include <linux/sched.h>
112#include <asm/io.h>
113#include <linux/blkdev.h>
114#include <linux/interrupt.h>
115#include <linux/stat.h>
116#include <linux/init.h>
117#include <linux/module.h>
118#include <linux/delay.h>
119
120#include "scsi.h"
121#include <scsi/scsi_host.h>
122#include "t128.h"
123#define AUTOPROBE_IRQ
124#include "NCR5380.h"
125
126static struct override {
127 unsigned long address;
128 int irq;
129} overrides
130#ifdef T128_OVERRIDE
131 [] __initdata = T128_OVERRIDE;
132#else
133 [4] __initdata = {{0, IRQ_AUTO}, {0, IRQ_AUTO},
134 {0 ,IRQ_AUTO}, {0, IRQ_AUTO}};
135#endif
136
137#define NO_OVERRIDES (sizeof(overrides) / sizeof(struct override))
138
139static struct base {
140 unsigned int address;
141 int noauto;
142} bases[] __initdata = {
143 { 0xcc000, 0}, { 0xc8000, 0}, { 0xdc000, 0}, { 0xd8000, 0}
144};
145
146#define NO_BASES (sizeof (bases) / sizeof (struct base))
147
148static struct signature {
149 const char *string;
150 int offset;
151} signatures[] __initdata = {
152{"TSROM: SCSI BIOS, Version 1.12", 0x36},
153};
154
155#define NO_SIGNATURES (sizeof (signatures) / sizeof (struct signature))
156
157/*
158 * Function : t128_setup(char *str, int *ints)
159 *
160 * Purpose : LILO command line initialization of the overrides array,
161 *
162 * Inputs : str - unused, ints - array of integer parameters with ints[0]
163 * equal to the number of ints.
164 *
165 */
166
167void __init t128_setup(char *str, int *ints){
168 static int commandline_current = 0;
169 int i;
170 if (ints[0] != 2)
171 printk("t128_setup : usage t128=address,irq\n");
172 else
173 if (commandline_current < NO_OVERRIDES) {
174 overrides[commandline_current].address = ints[1];
175 overrides[commandline_current].irq = ints[2];
176 for (i = 0; i < NO_BASES; ++i)
177 if (bases[i].address == ints[1]) {
178 bases[i].noauto = 1;
179 break;
180 }
181 ++commandline_current;
182 }
183}
184
185/*
186 * Function : int t128_detect(Scsi_Host_Template * tpnt)
187 *
188 * Purpose : detects and initializes T128,T128F, or T228 controllers
189 * that were autoprobed, overridden on the LILO command line,
190 * or specified at compile time.
191 *
192 * Inputs : tpnt - template for this SCSI adapter.
193 *
194 * Returns : 1 if a host adapter was found, 0 if not.
195 *
196 */
197
198int __init t128_detect(Scsi_Host_Template * tpnt){
199 static int current_override = 0, current_base = 0;
200 struct Scsi_Host *instance;
201 unsigned long base;
202 void __iomem *p;
203 int sig, count;
204
205 tpnt->proc_name = "t128";
206 tpnt->proc_info = &t128_proc_info;
207
208 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
209 base = 0;
210 p = NULL;
211
212 if (overrides[current_override].address) {
213 base = overrides[current_override].address;
214 p = ioremap(bases[current_base].address, 0x2000);
215 if (!p)
216 base = 0;
217 } else
218 for (; !base && (current_base < NO_BASES); ++current_base) {
219#if (TDEBUG & TDEBUG_INIT)
220 printk("scsi-t128 : probing address %08x\n", bases[current_base].address);
221#endif
222 if (bases[current_base].noauto)
223 continue;
224 p = ioremap(bases[current_base].address, 0x2000);
225 if (!p)
226 continue;
227 for (sig = 0; sig < NO_SIGNATURES; ++sig)
228 if (check_signature(p + signatures[sig].offset,
229 signatures[sig].string,
230 strlen(signatures[sig].string))) {
231 base = bases[current_base].address;
232#if (TDEBUG & TDEBUG_INIT)
233 printk("scsi-t128 : detected board.\n");
234#endif
235 goto found;
236 }
237 iounmap(p);
238 }
239
240#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
241 printk("scsi-t128 : base = %08x\n", (unsigned int) base);
242#endif
243
244 if (!base)
245 break;
246
247found:
248 instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
249 if(instance == NULL)
250 break;
251
252 instance->base = base;
253 ((struct NCR5380_hostdata *)instance->hostdata)->base = p;
254
255 NCR5380_init(instance, 0);
256
257 if (overrides[current_override].irq != IRQ_AUTO)
258 instance->irq = overrides[current_override].irq;
259 else
260 instance->irq = NCR5380_probe_irq(instance, T128_IRQS);
261
262 if (instance->irq != SCSI_IRQ_NONE)
263 if (request_irq(instance->irq, t128_intr, SA_INTERRUPT, "t128", instance)) {
264 printk("scsi%d : IRQ%d not free, interrupts disabled\n",
265 instance->host_no, instance->irq);
266 instance->irq = SCSI_IRQ_NONE;
267 }
268
269 if (instance->irq == SCSI_IRQ_NONE) {
270 printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
271 printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
272 }
273
274#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
275 printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
276#endif
277
278 printk("scsi%d : at 0x%08lx", instance->host_no, instance->base);
279 if (instance->irq == SCSI_IRQ_NONE)
280 printk (" interrupts disabled");
281 else
282 printk (" irq %d", instance->irq);
283 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
284 CAN_QUEUE, CMD_PER_LUN, T128_PUBLIC_RELEASE);
285 NCR5380_print_options(instance);
286 printk("\n");
287
288 ++current_override;
289 ++count;
290 }
291 return count;
292}
293
294static int t128_release(struct Scsi_Host *shost)
295{
296 NCR5380_local_declare();
297 NCR5380_setup(shost);
298 if (shost->irq)
299 free_irq(shost->irq, NULL);
300 NCR5380_exit(shost);
301 if (shost->io_port && shost->n_io_port)
302 release_region(shost->io_port, shost->n_io_port);
303 scsi_unregister(shost);
304 iounmap(base);
305 return 0;
306}
307
308/*
309 * Function : int t128_biosparam(Disk * disk, struct block_device *dev, int *ip)
310 *
311 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
312 * the specified device / size.
313 *
314 * Inputs : size = size of device in sectors (512 bytes), dev = block device
315 * major / minor, ip[] = {heads, sectors, cylinders}
316 *
317 * Returns : always 0 (success), initializes ip
318 *
319 */
320
321/*
322 * XXX Most SCSI boards use this mapping, I could be incorrect. Some one
323 * using hard disks on a trantor should verify that this mapping corresponds
324 * to that used by the BIOS / ASPI driver by running the linux fdisk program
325 * and matching the H_C_S coordinates to what DOS uses.
326 */
327
328int t128_biosparam(struct scsi_device *sdev, struct block_device *bdev,
329 sector_t capacity, int * ip)
330{
331 ip[0] = 64;
332 ip[1] = 32;
333 ip[2] = capacity >> 11;
334 return 0;
335}
336
337/*
338 * Function : int NCR5380_pread (struct Scsi_Host *instance,
339 * unsigned char *dst, int len)
340 *
341 * Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to
342 * dst
343 *
344 * Inputs : dst = destination, len = length in bytes
345 *
346 * Returns : 0 on success, non zero on a failure such as a watchdog
347 * timeout.
348 */
349
350static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,
351 int len) {
352 NCR5380_local_declare();
353 void __iomem *reg;
354 unsigned char *d = dst;
355 register int i = len;
356
357 NCR5380_setup(instance);
358 reg = base + T_DATA_REG_OFFSET;
359
360#if 0
361 for (; i; --i) {
362 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
363#else
364 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
365 for (; i; --i) {
366#endif
367 *d++ = readb(reg);
368 }
369
370 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
371 unsigned char tmp;
372 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
373 tmp = readb(foo);
374 writeb(tmp | T_CR_CT, foo);
375 writeb(tmp, foo);
376 printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
377 instance->host_no);
378 return -1;
379 } else
380 return 0;
381}
382
383/*
384 * Function : int NCR5380_pwrite (struct Scsi_Host *instance,
385 * unsigned char *src, int len)
386 *
387 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
388 * src
389 *
390 * Inputs : src = source, len = length in bytes
391 *
392 * Returns : 0 on success, non zero on a failure such as a watchdog
393 * timeout.
394 */
395
396static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,
397 int len) {
398 NCR5380_local_declare();
399 void __iomem *reg;
400 unsigned char *s = src;
401 register int i = len;
402
403 NCR5380_setup(instance);
404 reg = base + T_DATA_REG_OFFSET;
405
406#if 0
407 for (; i; --i) {
408 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
409#else
410 while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
411 for (; i; --i) {
412#endif
413 writeb(*s++, reg);
414 }
415
416 if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
417 unsigned char tmp;
418 void __iomem *foo = base + T_CONTROL_REG_OFFSET;
419 tmp = readb(foo);
420 writeb(tmp | T_CR_CT, foo);
421 writeb(tmp, foo);
422 printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
423 instance->host_no);
424 return -1;
425 } else
426 return 0;
427}
428
429MODULE_LICENSE("GPL");
430
431#include "NCR5380.c"
432
433static Scsi_Host_Template driver_template = {
434 .name = "Trantor T128/T128F/T228",
435 .detect = t128_detect,
436 .release = t128_release,
437 .queuecommand = t128_queue_command,
438 .eh_abort_handler = t128_abort,
439 .eh_bus_reset_handler = t128_bus_reset,
440 .eh_host_reset_handler = t128_host_reset,
441 .eh_device_reset_handler = t128_device_reset,
442 .bios_param = t128_biosparam,
443 .can_queue = CAN_QUEUE,
444 .this_id = 7,
445 .sg_tablesize = SG_ALL,
446 .cmd_per_lun = CMD_PER_LUN,
447 .use_clustering = DISABLE_CLUSTERING,
448};
449#include "scsi_module.c"