Blame - Documentation/hwmon/zl6100 - kernel/msm-4.9

blob: 51f76a189feead958ae094ab9608b87c74bcdacb [file] [log] [blame]

Guenter Roeck	200855e	2011-07-29 22:21:53 -0700	[diff] [blame]	1	Kernel driver zl6100
				2	====================
				3
				4	Supported chips:
				5	* Intersil / Zilker Labs ZL2004
				6	Prefix: 'zl2004'
				7	Addresses scanned: -
				8	Datasheet: http://www.intersil.com/data/fn/fn6847.pdf
Guenter Roeck	bc581e6	2011-10-01 16:50:36 -0700	[diff] [blame]	9	* Intersil / Zilker Labs ZL2005
				10	Prefix: 'zl2005'
				11	Addresses scanned: -
				12	Datasheet: http://www.intersil.com/data/fn/fn6848.pdf
Guenter Roeck	200855e	2011-07-29 22:21:53 -0700	[diff] [blame]	13	* Intersil / Zilker Labs ZL2006
				14	Prefix: 'zl2006'
				15	Addresses scanned: -
				16	Datasheet: http://www.intersil.com/data/fn/fn6850.pdf
				17	* Intersil / Zilker Labs ZL2008
				18	Prefix: 'zl2008'
				19	Addresses scanned: -
				20	Datasheet: http://www.intersil.com/data/fn/fn6859.pdf
				21	* Intersil / Zilker Labs ZL2105
				22	Prefix: 'zl2105'
				23	Addresses scanned: -
				24	Datasheet: http://www.intersil.com/data/fn/fn6851.pdf
				25	* Intersil / Zilker Labs ZL2106
				26	Prefix: 'zl2106'
				27	Addresses scanned: -
				28	Datasheet: http://www.intersil.com/data/fn/fn6852.pdf
				29	* Intersil / Zilker Labs ZL6100
				30	Prefix: 'zl6100'
				31	Addresses scanned: -
				32	Datasheet: http://www.intersil.com/data/fn/fn6876.pdf
				33	* Intersil / Zilker Labs ZL6105
				34	Prefix: 'zl6105'
				35	Addresses scanned: -
				36	Datasheet: http://www.intersil.com/data/fn/fn6906.pdf
Guenter Roeck	443830f	2011-10-01 17:35:44 -0700	[diff] [blame]	37	* Ericsson BMR450, BMR451
				38	Prefix: 'bmr450', 'bmr451'
				39	Addresses scanned: -
				40	Datasheet:
				41	http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146401
				42	* Ericsson BMR462, BMR463, BMR464
				43	Prefixes: 'bmr462', 'bmr463', 'bmr464'
				44	Addresses scanned: -
				45	Datasheet:
				46	http://archive.ericsson.net/service/internet/picov/get?DocNo=28701-EN/LZT146256
				47
Guenter Roeck	200855e	2011-07-29 22:21:53 -0700	[diff] [blame]	48
				49	Author: Guenter Roeck <guenter.roeck@ericsson.com>
				50
				51
				52	Description
				53	-----------
				54
				55	This driver supports hardware montoring for Intersil / Zilker Labs ZL6100 and
				56	compatible digital DC-DC controllers.
				57
				58	The driver is a client driver to the core PMBus driver. Please see
				59	Documentation/hwmon/pmbus and Documentation.hwmon/pmbus-core for details
				60	on PMBus client drivers.
				61
				62
				63	Usage Notes
				64	-----------
				65
				66	This driver does not auto-detect devices. You will have to instantiate the
				67	devices explicitly. Please see Documentation/i2c/instantiating-devices for
				68	details.
				69
				70	WARNING: Do not access chip registers using the i2cdump command, and do not use
				71	any of the i2ctools commands on a command register used to save and restore
				72	configuration data (0x11, 0x12, 0x15, 0x16, and 0xf4). The chips supported by
				73	this driver interpret any access to those command registers (including read
				74	commands) as request to execute the command in question. Unless write accesses
				75	to those registers are protected, this may result in power loss, board resets,
				76	and/or Flash corruption. Worst case, your board may turn into a brick.
				77
				78
				79	Platform data support
				80	---------------------
				81
				82	The driver supports standard PMBus driver platform data.
				83
				84
				85	Module parameters
				86	-----------------
				87
				88	delay
				89	-----
				90
				91	Some Intersil/Zilker Labs DC-DC controllers require a minimum interval between
				92	I2C bus accesses. According to Intersil, the minimum interval is 2 ms, though
				93	1 ms appears to be sufficient and has not caused any problems in testing.
				94	The problem is known to affect ZL6100, ZL2105, and ZL2008. It is known not to
				95	affect ZL2004 and ZL6105. The driver automatically sets the interval to 1 ms
				96	except for ZL2004 and ZL6105. To enable manual override, the driver provides a
				97	writeable module parameter, 'delay', which can be used to set the interval to
				98	a value between 0 and 65,535 microseconds.
				99
				100
				101	Sysfs entries
				102	-------------
				103
				104	The following attributes are supported. Limits are read-write; all other
				105	attributes are read-only.
				106
				107	in1_label "vin"
				108	in1_input Measured input voltage.
				109	in1_min Minimum input voltage.
				110	in1_max Maximum input voltage.
				111	in1_lcrit Critical minumum input voltage.
				112	in1_crit Critical maximum input voltage.
				113	in1_min_alarm Input voltage low alarm.
				114	in1_max_alarm Input voltage high alarm.
				115	in1_lcrit_alarm Input voltage critical low alarm.
				116	in1_crit_alarm Input voltage critical high alarm.
				117
				118	in2_label "vout1"
				119	in2_input Measured output voltage.
				120	in2_lcrit Critical minumum output Voltage.
				121	in2_crit Critical maximum output voltage.
				122	in2_lcrit_alarm Critical output voltage critical low alarm.
				123	in2_crit_alarm Critical output voltage critical high alarm.
				124
				125	curr1_label "iout1"
				126	curr1_input Measured output current.
				127	curr1_lcrit Critical minimum output current.
				128	curr1_crit Critical maximum output current.
				129	curr1_lcrit_alarm Output current critical low alarm.
				130	curr1_crit_alarm Output current critical high alarm.
				131
				132	temp[12]_input Measured temperature.
				133	temp[12]_min Minimum temperature.
				134	temp[12]_max Maximum temperature.
				135	temp[12]_lcrit Critical low temperature.
				136	temp[12]_crit Critical high temperature.
				137	temp[12]_min_alarm Chip temperature low alarm.
				138	temp[12]_max_alarm Chip temperature high alarm.
				139	temp[12]_lcrit_alarm Chip temperature critical low alarm.
				140	temp[12]_crit_alarm Chip temperature critical high alarm.