Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 1 | /* |
| 2 | * Shared Transport Header file |
| 3 | * To be included by the protocol stack drivers for |
| 4 | * Texas Instruments BT,FM and GPS combo chip drivers |
| 5 | * and also serves the sub-modules of the shared transport driver. |
| 6 | * |
| 7 | * Copyright (C) 2009-2010 Texas Instruments |
| 8 | * Author: Pavan Savoy <pavan_savoy@ti.com> |
| 9 | * |
| 10 | * This program is free software; you can redistribute it and/or modify |
| 11 | * it under the terms of the GNU General Public License version 2 as |
| 12 | * published by the Free Software Foundation. |
| 13 | * |
| 14 | * This program is distributed in the hope that it will be useful, |
| 15 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 16 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 17 | * GNU General Public License for more details. |
| 18 | * |
| 19 | * You should have received a copy of the GNU General Public License |
| 20 | * along with this program; if not, write to the Free Software |
| 21 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| 22 | * |
| 23 | */ |
| 24 | |
| 25 | #ifndef TI_WILINK_ST_H |
| 26 | #define TI_WILINK_ST_H |
| 27 | |
Mircea Gherzan | 9624f61 | 2012-05-09 14:19:13 -0700 | [diff] [blame] | 28 | #include <linux/skbuff.h> |
| 29 | |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 30 | /** |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 31 | * enum proto-type - The protocol on WiLink chips which share a |
| 32 | * common physical interface like UART. |
| 33 | */ |
| 34 | enum proto_type { |
| 35 | ST_BT, |
| 36 | ST_FM, |
| 37 | ST_GPS, |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 38 | ST_MAX_CHANNELS = 16, |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 39 | }; |
| 40 | |
| 41 | /** |
| 42 | * struct st_proto_s - Per Protocol structure from BT/FM/GPS to ST |
| 43 | * @type: type of the protocol being registered among the |
| 44 | * available proto_type(BT, FM, GPS the protocol which share TTY). |
| 45 | * @recv: the receiver callback pointing to a function in the |
| 46 | * protocol drivers called by the ST driver upon receiving |
| 47 | * relevant data. |
| 48 | * @match_packet: reserved for future use, to make ST more generic |
| 49 | * @reg_complete_cb: callback handler pointing to a function in protocol |
| 50 | * handler called by ST when the pending registrations are complete. |
| 51 | * The registrations are marked pending, in situations when fw |
| 52 | * download is in progress. |
| 53 | * @write: pointer to function in ST provided to protocol drivers from ST, |
| 54 | * to be made use when protocol drivers have data to send to TTY. |
| 55 | * @priv_data: privdate data holder for the protocol drivers, sent |
| 56 | * from the protocol drivers during registration, and sent back on |
| 57 | * reg_complete_cb and recv. |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 58 | * @chnl_id: channel id the protocol driver is interested in, the channel |
| 59 | * id is nothing but the 1st byte of the packet in UART frame. |
| 60 | * @max_frame_size: size of the largest frame the protocol can receive. |
| 61 | * @hdr_len: length of the header structure of the protocol. |
| 62 | * @offset_len_in_hdr: this provides the offset of the length field in the |
| 63 | * header structure of the protocol header, to assist ST to know |
| 64 | * how much to receive, if the data is split across UART frames. |
| 65 | * @len_size: whether the length field inside the header is 2 bytes |
| 66 | * or 1 byte. |
| 67 | * @reserve: the number of bytes ST needs to reserve in the skb being |
| 68 | * prepared for the protocol driver. |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 69 | */ |
| 70 | struct st_proto_s { |
| 71 | enum proto_type type; |
| 72 | long (*recv) (void *, struct sk_buff *); |
| 73 | unsigned char (*match_packet) (const unsigned char *data); |
| 74 | void (*reg_complete_cb) (void *, char data); |
| 75 | long (*write) (struct sk_buff *skb); |
| 76 | void *priv_data; |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 77 | |
| 78 | unsigned char chnl_id; |
| 79 | unsigned short max_frame_size; |
| 80 | unsigned char hdr_len; |
| 81 | unsigned char offset_len_in_hdr; |
| 82 | unsigned char len_size; |
| 83 | unsigned char reserve; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 84 | }; |
| 85 | |
| 86 | extern long st_register(struct st_proto_s *); |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 87 | extern long st_unregister(struct st_proto_s *); |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 88 | |
Gigi Joseph | 46d0d33 | 2015-01-09 03:45:02 +0000 | [diff] [blame^] | 89 | extern struct ti_st_plat_data *dt_pdata; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 90 | |
| 91 | /* |
| 92 | * header information used by st_core.c |
| 93 | */ |
| 94 | |
| 95 | /* states of protocol list */ |
| 96 | #define ST_NOTEMPTY 1 |
| 97 | #define ST_EMPTY 0 |
| 98 | |
| 99 | /* |
| 100 | * possible st_states |
| 101 | */ |
| 102 | #define ST_INITIALIZING 1 |
| 103 | #define ST_REG_IN_PROGRESS 2 |
| 104 | #define ST_REG_PENDING 3 |
| 105 | #define ST_WAITING_FOR_RESP 4 |
| 106 | |
| 107 | /** |
| 108 | * struct st_data_s - ST core internal structure |
| 109 | * @st_state: different states of ST like initializing, registration |
| 110 | * in progress, this is mainly used to return relevant err codes |
| 111 | * when protocol drivers are registering. It is also used to track |
| 112 | * the recv function, as in during fw download only HCI events |
| 113 | * can occur , where as during other times other events CH8, CH9 |
| 114 | * can occur. |
| 115 | * @tty: tty provided by the TTY core for line disciplines. |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 116 | * @tx_skb: If for some reason the tty's write returns lesser bytes written |
| 117 | * then to maintain the rest of data to be written on next instance. |
| 118 | * This needs to be protected, hence the lock inside wakeup func. |
| 119 | * @tx_state: if the data is being written onto the TTY and protocol driver |
| 120 | * wants to send more, queue up data and mark that there is |
| 121 | * more data to send. |
| 122 | * @list: the list of protocols registered, only MAX can exist, one protocol |
| 123 | * can register only once. |
| 124 | * @rx_state: states to be maintained inside st's tty receive |
| 125 | * @rx_count: count to be maintained inside st's tty receieve |
| 126 | * @rx_skb: the skb where all data for a protocol gets accumulated, |
| 127 | * since tty might not call receive when a complete event packet |
| 128 | * is received, the states, count and the skb needs to be maintained. |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 129 | * @rx_chnl: the channel ID for which the data is getting accumalated for. |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 130 | * @txq: the list of skbs which needs to be sent onto the TTY. |
| 131 | * @tx_waitq: if the chip is not in AWAKE state, the skbs needs to be queued |
| 132 | * up in here, PM(WAKEUP_IND) data needs to be sent and then the skbs |
| 133 | * from waitq can be moved onto the txq. |
| 134 | * Needs locking too. |
| 135 | * @lock: the lock to protect skbs, queues, and ST states. |
| 136 | * @protos_registered: count of the protocols registered, also when 0 the |
| 137 | * chip enable gpio can be toggled, and when it changes to 1 the fw |
| 138 | * needs to be downloaded to initialize chip side ST. |
| 139 | * @ll_state: the various PM states the chip can be, the states are notified |
| 140 | * to us, when the chip sends relevant PM packets(SLEEP_IND, WAKE_IND). |
| 141 | * @kim_data: reference to the parent encapsulating structure. |
| 142 | * |
| 143 | */ |
| 144 | struct st_data_s { |
| 145 | unsigned long st_state; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 146 | struct sk_buff *tx_skb; |
| 147 | #define ST_TX_SENDING 1 |
| 148 | #define ST_TX_WAKEUP 2 |
| 149 | unsigned long tx_state; |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 150 | struct st_proto_s *list[ST_MAX_CHANNELS]; |
Pavan Savoy | 764b0c4 | 2011-04-08 04:57:42 -0500 | [diff] [blame] | 151 | bool is_registered[ST_MAX_CHANNELS]; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 152 | unsigned long rx_state; |
| 153 | unsigned long rx_count; |
| 154 | struct sk_buff *rx_skb; |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 155 | unsigned char rx_chnl; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 156 | struct sk_buff_head txq, tx_waitq; |
| 157 | spinlock_t lock; |
| 158 | unsigned char protos_registered; |
| 159 | unsigned long ll_state; |
| 160 | void *kim_data; |
Pavan Savoy | 764b0c4 | 2011-04-08 04:57:42 -0500 | [diff] [blame] | 161 | struct tty_struct *tty; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 162 | }; |
| 163 | |
Pavan Savoy | ef04d12 | 2011-02-04 02:23:13 -0600 | [diff] [blame] | 164 | /* |
| 165 | * wrapper around tty->ops->write_room to check |
| 166 | * availability during firmware download |
| 167 | */ |
| 168 | int st_get_uart_wr_room(struct st_data_s *st_gdata); |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 169 | /** |
| 170 | * st_int_write - |
| 171 | * point this to tty->driver->write or tty->ops->write |
| 172 | * depending upon the kernel version |
| 173 | */ |
| 174 | int st_int_write(struct st_data_s*, const unsigned char*, int); |
| 175 | |
| 176 | /** |
| 177 | * st_write - |
| 178 | * internal write function, passed onto protocol drivers |
| 179 | * via the write function ptr of protocol struct |
| 180 | */ |
| 181 | long st_write(struct sk_buff *); |
| 182 | |
| 183 | /* function to be called from ST-LL */ |
| 184 | void st_ll_send_frame(enum proto_type, struct sk_buff *); |
| 185 | |
| 186 | /* internal wake up function */ |
| 187 | void st_tx_wakeup(struct st_data_s *st_data); |
| 188 | |
| 189 | /* init, exit entry funcs called from KIM */ |
| 190 | int st_core_init(struct st_data_s **); |
| 191 | void st_core_exit(struct st_data_s *); |
| 192 | |
| 193 | /* ask for reference from KIM */ |
| 194 | void st_kim_ref(struct st_data_s **, int); |
| 195 | |
| 196 | #define GPS_STUB_TEST |
| 197 | #ifdef GPS_STUB_TEST |
| 198 | int gps_chrdrv_stub_write(const unsigned char*, int); |
| 199 | void gps_chrdrv_stub_init(void); |
| 200 | #endif |
| 201 | |
| 202 | /* |
| 203 | * header information used by st_kim.c |
| 204 | */ |
| 205 | |
| 206 | /* time in msec to wait for |
| 207 | * line discipline to be installed |
| 208 | */ |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 209 | #define LDISC_TIME 1000 |
| 210 | #define CMD_RESP_TIME 800 |
Pavan Savoy | ef04d12 | 2011-02-04 02:23:13 -0600 | [diff] [blame] | 211 | #define CMD_WR_TIME 5000 |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 212 | #define MAKEWORD(a, b) ((unsigned short)(((unsigned char)(a)) \ |
| 213 | | ((unsigned short)((unsigned char)(b))) << 8)) |
| 214 | |
| 215 | #define GPIO_HIGH 1 |
| 216 | #define GPIO_LOW 0 |
| 217 | |
| 218 | /* the Power-On-Reset logic, requires to attempt |
| 219 | * to download firmware onto chip more than once |
| 220 | * since the self-test for chip takes a while |
| 221 | */ |
| 222 | #define POR_RETRY_COUNT 5 |
| 223 | |
| 224 | /** |
| 225 | * struct chip_version - save the chip version |
| 226 | */ |
| 227 | struct chip_version { |
| 228 | unsigned short full; |
| 229 | unsigned short chip; |
| 230 | unsigned short min_ver; |
| 231 | unsigned short maj_ver; |
| 232 | }; |
| 233 | |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 234 | #define UART_DEV_NAME_LEN 32 |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 235 | /** |
| 236 | * struct kim_data_s - the KIM internal data, embedded as the |
| 237 | * platform's drv data. One for each ST device in the system. |
| 238 | * @uim_pid: KIM needs to communicate with UIM to request to install |
| 239 | * the ldisc by opening UART when protocol drivers register. |
| 240 | * @kim_pdev: the platform device added in one of the board-XX.c file |
| 241 | * in arch/XX/ directory, 1 for each ST device. |
| 242 | * @kim_rcvd: completion handler to notify when data was received, |
| 243 | * mainly used during fw download, which involves multiple send/wait |
| 244 | * for each of the HCI-VS commands. |
| 245 | * @ldisc_installed: completion handler to notify that the UIM accepted |
| 246 | * the request to install ldisc, notify from tty_open which suggests |
| 247 | * the ldisc was properly installed. |
| 248 | * @resp_buffer: data buffer for the .bts fw file name. |
| 249 | * @fw_entry: firmware class struct to request/release the fw. |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 250 | * @rx_state: the rx state for kim's receive func during fw download. |
| 251 | * @rx_count: the rx count for the kim's receive func during fw download. |
| 252 | * @rx_skb: all of fw data might not come at once, and hence data storage for |
| 253 | * whole of the fw response, only HCI_EVENTs and hence diff from ST's |
| 254 | * response. |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 255 | * @core_data: ST core's data, which mainly is the tty's disc_data |
| 256 | * @version: chip version available via a sysfs entry. |
| 257 | * |
| 258 | */ |
| 259 | struct kim_data_s { |
| 260 | long uim_pid; |
| 261 | struct platform_device *kim_pdev; |
| 262 | struct completion kim_rcvd, ldisc_installed; |
| 263 | char resp_buffer[30]; |
| 264 | const struct firmware *fw_entry; |
Pavan Savoy | 781a739 | 2011-02-04 02:23:15 -0600 | [diff] [blame] | 265 | long nshutdown; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 266 | unsigned long rx_state; |
| 267 | unsigned long rx_count; |
| 268 | struct sk_buff *rx_skb; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 269 | struct st_data_s *core_data; |
| 270 | struct chip_version version; |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 271 | unsigned char ldisc_install; |
Lee Jones | ffdbb71 | 2014-08-28 14:14:09 +0100 | [diff] [blame] | 272 | unsigned char dev_name[UART_DEV_NAME_LEN + 1]; |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 273 | unsigned char flow_cntrl; |
| 274 | unsigned long baud_rate; |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 275 | }; |
| 276 | |
| 277 | /** |
| 278 | * functions called when 1 of the protocol drivers gets |
| 279 | * registered, these need to communicate with UIM to request |
| 280 | * ldisc installed, read chip_version, download relevant fw |
| 281 | */ |
| 282 | long st_kim_start(void *); |
| 283 | long st_kim_stop(void *); |
| 284 | |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 285 | void st_kim_complete(void *); |
| 286 | void kim_st_list_protocols(struct st_data_s *, void *); |
Pavan Savoy | 27712b3 | 2012-08-03 14:49:40 -0500 | [diff] [blame] | 287 | void st_kim_recv(void *, const unsigned char *, long); |
| 288 | |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 289 | |
| 290 | /* |
| 291 | * BTS headers |
| 292 | */ |
| 293 | #define ACTION_SEND_COMMAND 1 |
| 294 | #define ACTION_WAIT_EVENT 2 |
| 295 | #define ACTION_SERIAL 3 |
| 296 | #define ACTION_DELAY 4 |
| 297 | #define ACTION_RUN_SCRIPT 5 |
| 298 | #define ACTION_REMARKS 6 |
| 299 | |
| 300 | /** |
| 301 | * struct bts_header - the fw file is NOT binary which can |
| 302 | * be sent onto TTY as is. The .bts is more a script |
| 303 | * file which has different types of actions. |
| 304 | * Each such action needs to be parsed by the KIM and |
| 305 | * relevant procedure to be called. |
| 306 | */ |
| 307 | struct bts_header { |
| 308 | u32 magic; |
| 309 | u32 version; |
| 310 | u8 future[24]; |
| 311 | u8 actions[0]; |
| 312 | } __attribute__ ((packed)); |
| 313 | |
| 314 | /** |
| 315 | * struct bts_action - Each .bts action has its own type of |
| 316 | * data. |
| 317 | */ |
| 318 | struct bts_action { |
| 319 | u16 type; |
| 320 | u16 size; |
| 321 | u8 data[0]; |
| 322 | } __attribute__ ((packed)); |
| 323 | |
| 324 | struct bts_action_send { |
| 325 | u8 data[0]; |
| 326 | } __attribute__ ((packed)); |
| 327 | |
| 328 | struct bts_action_wait { |
| 329 | u32 msec; |
| 330 | u32 size; |
| 331 | u8 data[0]; |
| 332 | } __attribute__ ((packed)); |
| 333 | |
| 334 | struct bts_action_delay { |
| 335 | u32 msec; |
| 336 | } __attribute__ ((packed)); |
| 337 | |
| 338 | struct bts_action_serial { |
| 339 | u32 baud; |
| 340 | u32 flow_control; |
| 341 | } __attribute__ ((packed)); |
| 342 | |
| 343 | /** |
| 344 | * struct hci_command - the HCI-VS for intrepreting |
| 345 | * the change baud rate of host-side UART, which |
| 346 | * needs to be ignored, since UIM would do that |
| 347 | * when it receives request from KIM for ldisc installation. |
| 348 | */ |
| 349 | struct hci_command { |
| 350 | u8 prefix; |
| 351 | u16 opcode; |
| 352 | u8 plen; |
| 353 | u32 speed; |
| 354 | } __attribute__ ((packed)); |
| 355 | |
| 356 | /* |
| 357 | * header information used by st_ll.c |
| 358 | */ |
| 359 | |
| 360 | /* ST LL receiver states */ |
| 361 | #define ST_W4_PACKET_TYPE 0 |
Pavan Savoy | 5c88b02 | 2011-02-04 02:23:09 -0600 | [diff] [blame] | 362 | #define ST_W4_HEADER 1 |
| 363 | #define ST_W4_DATA 2 |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 364 | |
| 365 | /* ST LL state machines */ |
| 366 | #define ST_LL_ASLEEP 0 |
| 367 | #define ST_LL_ASLEEP_TO_AWAKE 1 |
| 368 | #define ST_LL_AWAKE 2 |
| 369 | #define ST_LL_AWAKE_TO_ASLEEP 3 |
| 370 | #define ST_LL_INVALID 4 |
| 371 | |
| 372 | /* different PM notifications coming from chip */ |
| 373 | #define LL_SLEEP_IND 0x30 |
| 374 | #define LL_SLEEP_ACK 0x31 |
| 375 | #define LL_WAKE_UP_IND 0x32 |
| 376 | #define LL_WAKE_UP_ACK 0x33 |
| 377 | |
| 378 | /* initialize and de-init ST LL */ |
| 379 | long st_ll_init(struct st_data_s *); |
| 380 | long st_ll_deinit(struct st_data_s *); |
| 381 | |
| 382 | /** |
| 383 | * enable/disable ST LL along with KIM start/stop |
| 384 | * called by ST Core |
| 385 | */ |
| 386 | void st_ll_enable(struct st_data_s *); |
| 387 | void st_ll_disable(struct st_data_s *); |
| 388 | |
| 389 | /** |
| 390 | * various funcs used by ST core to set/get the various PM states |
| 391 | * of the chip. |
| 392 | */ |
| 393 | unsigned long st_ll_getstate(struct st_data_s *); |
| 394 | unsigned long st_ll_sleep_state(struct st_data_s *, unsigned char); |
| 395 | void st_ll_wakeup(struct st_data_s *); |
| 396 | |
| 397 | /* |
| 398 | * header information used by st_core.c for FM and GPS |
| 399 | * packet parsing, the bluetooth headers are already available |
| 400 | * at net/bluetooth/ |
| 401 | */ |
| 402 | |
| 403 | struct fm_event_hdr { |
| 404 | u8 plen; |
| 405 | } __attribute__ ((packed)); |
| 406 | |
| 407 | #define FM_MAX_FRAME_SIZE 0xFF /* TODO: */ |
| 408 | #define FM_EVENT_HDR_SIZE 1 /* size of fm_event_hdr */ |
| 409 | #define ST_FM_CH8_PKT 0x8 |
| 410 | |
| 411 | /* gps stuff */ |
| 412 | struct gps_event_hdr { |
| 413 | u8 opcode; |
| 414 | u16 plen; |
| 415 | } __attribute__ ((packed)); |
| 416 | |
Pavan Savoy | 0d7c5f2 | 2011-08-10 10:18:31 -0500 | [diff] [blame] | 417 | /** |
| 418 | * struct ti_st_plat_data - platform data shared between ST driver and |
| 419 | * platform specific board file which adds the ST device. |
| 420 | * @nshutdown_gpio: Host's GPIO line to which chip's BT_EN is connected. |
| 421 | * @dev_name: The UART/TTY name to which chip is interfaced. (eg: /dev/ttyS1) |
| 422 | * @flow_cntrl: Should always be 1, since UART's CTS/RTS is used for PM |
| 423 | * purposes. |
| 424 | * @baud_rate: The baud rate supported by the Host UART controller, this will |
| 425 | * be shared across with the chip via a HCI VS command from User-Space Init |
| 426 | * Mgr application. |
| 427 | * @suspend: |
| 428 | * @resume: legacy PM routines hooked to platform specific board file, so as |
| 429 | * to take chip-host interface specific action. |
| 430 | * @chip_enable: |
| 431 | * @chip_disable: Platform/Interface specific mux mode setting, GPIO |
| 432 | * configuring, Host side PM disabling etc.. can be done here. |
| 433 | * @chip_asleep: |
| 434 | * @chip_awake: Chip specific deep sleep states is communicated to Host |
| 435 | * specific board-xx.c to take actions such as cut UART clocks when chip |
| 436 | * asleep or run host faster when chip awake etc.. |
| 437 | * |
| 438 | */ |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 439 | struct ti_st_plat_data { |
Pavan Savoy | 781a739 | 2011-02-04 02:23:15 -0600 | [diff] [blame] | 440 | long nshutdown_gpio; |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 441 | unsigned char dev_name[UART_DEV_NAME_LEN]; /* uart name */ |
| 442 | unsigned char flow_cntrl; /* flow control flag */ |
| 443 | unsigned long baud_rate; |
| 444 | int (*suspend)(struct platform_device *, pm_message_t); |
| 445 | int (*resume)(struct platform_device *); |
Pavan Savoy | 0d7c5f2 | 2011-08-10 10:18:31 -0500 | [diff] [blame] | 446 | int (*chip_enable) (struct kim_data_s *); |
| 447 | int (*chip_disable) (struct kim_data_s *); |
| 448 | int (*chip_asleep) (struct kim_data_s *); |
| 449 | int (*chip_awake) (struct kim_data_s *); |
Pavan Savoy | ec60d0a | 2011-02-04 02:23:10 -0600 | [diff] [blame] | 450 | }; |
| 451 | |
Pavan Savoy | 83ef41f | 2010-09-17 12:06:11 -0400 | [diff] [blame] | 452 | #endif /* TI_WILINK_ST_H */ |