arch/arm64/boot/dts/qcom/sdw3100-msm8909w-wtp.dts

/*
 * Copyright (c) 2017-2018 The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

/dts-v1/;

#include "msm8909-mtp.dtsi"
#include "msm8909w-gpu.dtsi"
#include "msm8909w.dtsi"
#include "msm8909w-bg-memory.dtsi"
#include "8909w-pm660.dtsi"
#include "msm8909-audio-bg_codec.dtsi"

/ {
	model = "Qualcomm Technologies, Inc. MSM8909W-PM660 BG WTP SDW3100";
	compatible = "qcom,msm8909-mtp", "qcom,msm8909", "qcom,mtp";
	qcom,msm-id =   <245 0>,
			<258 0>,
			<275 0>,
			<300 0>;
	qcom,board-id = <8 0x10f>,
			<8 0x117>;
	qcom,pmic-id =  <0x0001001b 0x0 0x0 0x0>,
			<0x0001011b 0x0 0x0 0x0>;
};

&soc {
	i2c@78b9000 { /* BLSP1 QUP5 */
		synaptics@20 {
			compatible = "synaptics,dsx-i2c";
			reg = <0x20>;
			interrupt-parent = <&msm_gpio>;
			interrupts = <98 0x2008>;
			vdd_ana-supply = <&pm660_l18>;
			vcc_i2c-supply = <&pm660_l13>;
			synaptics,pwr-reg-name = "vdd_ana";
			synaptics,bus-reg-name = "vcc_i2c";
			pinctrl-names = "pmx_ts_active", "pmx_ts_suspend",
							"pmx_ts_release";
			pinctrl-0 = <&ts_int_active &ts_reset_active>;
			pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
			pinctrl-2 = <&ts_release>;
			synaptics,irq-gpio = <&msm_gpio 98 0x2008>;
			synaptics,irq-on-state = <0>;
			synaptics,irq-flags = <0x2008>;
			synaptics,power-delay-ms = <200>;
			synaptics,reset-delay-ms = <200>;
			synaptics,max-y-for-2d = <389>;
			synaptics,bus-lpm-cur-uA = <450>;
			synaptics,do-not-disable-regulators;
			synaptics,wakeup-gestures-en;
			synaptics,resume-in-workqueue;
			synaptics,fw-name = "PR1814809-s1222_30303032.img";
			/delete-property/ synaptics,reset-gpio;
			/delete-property/ synaptics,display-coords;
			/delete-property/ synaptics,panel-coords;
			/delete-property/ synaptics,power-down;
			/delete-property/ synaptics,disable-gpios;
			/delete-property/ synaptics,is_wake;
		};

		/delete-node/ it7260@46;
	};

	qcom,blackghost {
		compatible = "qcom,pil-blackghost";
		qcom,pil-force-shutdown;
		qcom,firmware-name = "bg-wear";
		/* GPIO inputs from blackghost */
		qcom,bg2ap-status-gpio = <&msm_gpio 97 0>;
		qcom,bg2ap-errfatal-gpio = <&msm_gpio 95 0>;
		/* GPIO output to blackghost */
		qcom,ap2bg-status-gpio = <&msm_gpio 17 0>;
		qcom,ap2bg-errfatal-gpio = <&msm_gpio 23 0>;
	};

	qcom,msm-ssc-sensors {
		compatible = "qcom,msm-ssc-sensors";
	};

	qcom,glink-bgcom-xprt-bg {
		compatible = "qcom,glink-bgcom-xprt";
		label = "bg";
		qcom,qos-config = <&glink_qos_bg>;
		qcom,ramp-time = <0x10>,
				     <0x20>,
				     <0x30>,
				     <0x40>;
	};

	glink_qos_bg: qcom,glink-qos-config-bg {
		compatible = "qcom,glink-qos-config";
		qcom,flow-info = <0x80 0x0>,
				 <0x70 0x1>,
				 <0x60 0x2>,
				 <0x50 0x3>;
		qcom,mtu-size = <0x800>;
		qcom,tput-stats-cycle = <0xa>;
	};

	qcom,glink_pkt {
		compatible = "qcom,glinkpkt";

		qcom,glinkpkt-bg-daemon {
			qcom,glinkpkt-transport = "bgcom";
			qcom,glinkpkt-edge = "bg";
			qcom,glinkpkt-ch-name = "bg-daemon";
			qcom,glinkpkt-dev-name = "glink_pkt_bg_daemon";
		};

		qcom,glinkpkt-bg-display-ctrl {
			qcom,glinkpkt-transport = "bgcom";
			qcom,glinkpkt-edge = "bg";
			qcom,glinkpkt-ch-name = "display-ctrl";
			qcom,glinkpkt-dev-name = "glink_pkt_bg_display_ctrl";
		};

		qcom,glinkpkt-bg-display-data {
			qcom,glinkpkt-transport = "bgcom";
			qcom,glinkpkt-edge = "bg";
			qcom,glinkpkt-ch-name = "display-data";
			qcom,glinkpkt-dev-name = "glink_pkt_bg_display_data";
		};

		qcom,glinkpkt-bg-rsb-ctrl {
			qcom,glinkpkt-transport = "bgcom";
			qcom,glinkpkt-edge = "bg";
			qcom,glinkpkt-ch-name = "RSB_CTRL";
			qcom,glinkpkt-dev-name = "glink_pkt_bg_rsb_ctrl";
		};

		qcom,glinkpkt-bg-sso-ctrl {
			qcom,glinkpkt-transport = "bgcom";
			qcom,glinkpkt-edge = "bg";
			qcom,glinkpkt-ch-name = "sso-ctrl";
			qcom,glinkpkt-dev-name = "glink_pkt_bg_sso_ctrl";
		};
	};

	spi@78B8000 {  /* BLSP1 QUP4 */
		status = "ok";
		qcom,bg-spi {
			compatible = "qcom,bg-spi";
			reg = <0>;
			spi-max-frequency = <16000000>;
			interrupt-parent = <&msm_gpio>;
			qcom,irq-gpio = <&msm_gpio 110 1>;
		};
	};

	qcom,msm-thermal {
		vdd-dig-supply = <&pm660_s2_floor_corner>;

		msm_thermal_freq: qcom,vdd-apps-rstr {
			qcom,vdd-rstr-reg = "vdd-apps";
			qcom,levels = <1094400>;
			qcom,freq-req;
		};
	};

	qcom,bg-rsb {
		compatible = "qcom,bg-rsb";
		vdd-ldo1-supply = <&pm660_l11>;
		vdd-ldo2-supply = <&pm660_l15>;
	};

	qcom,bg-daemon {
		compatible = "qcom,bg-daemon";
		qcom,bg-reset-gpio = <&pm660_gpios 5 0>;
		ssr-reg1-supply = <&pm660_l3>;
		ssr-reg2-supply = <&pm660_l9>;
	};

	qcom,bcl {
		compatible = "qcom,bcl";
		qcom,bcl-enable;
		qcom,bcl-framework-interface;
		qcom,bcl-freq-control-list = <&CPU0 &CPU1 &CPU2 &CPU3>;
		qcom,bcl-hotplug-list = <&CPU2 &CPU3>;
		qcom,bcl-soc-hotplug-list = <&CPU2 &CPU3>;
		qcom,ibat-monitor {
			qcom,low-threshold-uamp = <1000000>;
			qcom,high-threshold-uamp = <2000000>;
			qcom,mitigation-freq-khz = <1094400>;
			qcom,vph-high-threshold-uv = <3500000>;
			qcom,vph-low-threshold-uv = <3200000>;
			qcom,soc-low-threshold = <10>;
			qcom,thermal-handle = <&msm_thermal_freq>;
		};
	};
};

&audio_codec_mtp {
	status = "disabled";
};

&audio_codec_bg {
	status = "ok";
};

&bg_cdc {
	status = "ok";
	vdd-spkr-supply = <&pm660_l11>;
};

&i2c_1 {
	status = "okay";
	nq@28 {
		compatible = "qcom,nq-nci";
		reg = <0x28>;
		qcom,nq-irq = <&msm_gpio 50 0x00>;
		qcom,nq-ven = <&msm_gpio 36 0x00>;
		qcom,nq-firm = <&msm_gpio 38 0x00>;
		qcom,nq-esepwr = <&msm_gpio 49 0x00>;
		qcom,nq-clkreq = <&pm660_gpios 4 0x00>;
		qcom,clk-src = "BBCLK3";
		interrupt-parent = <&msm_gpio>;
		interrupts = <50 0>;
		interrupt-names = "nfc_irq";
		pinctrl-names = "nfc_active","nfc_suspend";
		pinctrl-0 = <&nfcw_int_active
			     &nfcw_disable_active
			     &nfc_clk_default>;
		pinctrl-1 = <&nfcw_int_suspend &nfcw_disable_suspend>;
		clocks = <&clock_rpm clk_bb_clk3_pin>;
		clock-names = "ref_clk";
	};
};

&spi_0 {
	status = "disabled";
};

&i2c_3 {
	status = "disabled";
};

&i2c_4 {
	status = "disabled";
};

&i2c_2 {
	status = "disabled";
};

&sdc1_clk_off {
	config {
		pins = "sdc1_clk";
		bias-disable; /* NO pull */
		drive-strength = <2>; /* 2 MA */
		output-low;
	};
};

&sdc1_cmd_off {
	config {
		pins = "sdc1_cmd";
		bias-disable; /* NO pull */
		drive-strength = <2>; /* 2 MA */
		output-low;
	};
};

&sdc1_data_off {
	config {
		pins = "sdc1_data";
		bias-disable; /* NO pull */
		drive-strength = <2>; /* 2 MA */
		output-low;
	};
};

&sdhc_2 {
	status = "disabled";
};

&blsp1_uart1 {
	status = "ok";
	pinctrl-names = "default";
	pinctrl-0 = <&uart_console_sleep>;
};

/* Pinctrl dt nodes for interrupt & reset gpio for Synaptics touch controller */
&ts_int_active {
	mux {
		pins = "gpio98";
	};

	config {
		pins = "gpio98";
	};
};

&ts_int_suspend {
	mux {
		pins = "gpio98";
	};

	config {
		pins = "gpio98";
		/delete-property/ bias-pull-down;
		bias-disable; /* No PULL */
	};
};

&ts_reset_active {
	mux {
		pins = "gpio16";
	};

	config {
		pins = "gpio16";
	};
};

&ts_reset_suspend {
	mux {
		pins = "gpio16";
	};

	config {
		pins = "gpio16";
	};
};

&ts_release {
	mux {
		pins = "gpio98", "gpio16";
	};

	config {
		pins = "gpio98", "gpio16";
	};
};

&spi4_cs0_active {
	mux {
		pins = "gpio14";
		function = "blsp_spi4";
	};
	config {
		pins = "gpio14";
		drive-strength = <2>;
		bias-disable; /* No PULL */
		output-high;
	};
};

&mdss_dsi0 {
	qcom,dsi-pref-prim-pan = <&dsi_auo_390p_cmd>;
	qcom,platform-bklight-en-gpio = <&msm_gpio 52 0>;
	qcom,platform-enable-gpio = <&msm_gpio 59 0>;
};