drivers/media/i2c/soc_camera/ov2640.c

/*
 * ov2640 Camera Driver
 *
 * Copyright (C) 2010 Alberto Panizzo <maramaopercheseimorto@gmail.com>
 *
 * Based on ov772x, ov9640 drivers and previous non merged implementations.
 *
 * Copyright 2005-2009 Freescale Semiconductor, Inc. All Rights Reserved.
 * Copyright (C) 2006, OmniVision
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/init.h>
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/v4l2-mediabus.h>
#include <linux/videodev2.h>

#include <media/soc_camera.h>
#include <media/v4l2-clk.h>
#include <media/v4l2-subdev.h>
#include <media/v4l2-ctrls.h>

#define VAL_SET(x, mask, rshift, lshift)  \
		((((x) >> rshift) & mask) << lshift)
/*
 * DSP registers
 * register offset for BANK_SEL == BANK_SEL_DSP
 */
#define R_BYPASS    0x05 /* Bypass DSP */
#define   R_BYPASS_DSP_BYPAS    0x01 /* Bypass DSP, sensor out directly */
#define   R_BYPASS_USE_DSP      0x00 /* Use the internal DSP */
#define QS          0x44 /* Quantization Scale Factor */
#define CTRLI       0x50
#define   CTRLI_LP_DP           0x80
#define   CTRLI_ROUND           0x40
#define   CTRLI_V_DIV_SET(x)    VAL_SET(x, 0x3, 0, 3)
#define   CTRLI_H_DIV_SET(x)    VAL_SET(x, 0x3, 0, 0)
#define HSIZE       0x51 /* H_SIZE[7:0] (real/4) */
#define   HSIZE_SET(x)          VAL_SET(x, 0xFF, 2, 0)
#define VSIZE       0x52 /* V_SIZE[7:0] (real/4) */
#define   VSIZE_SET(x)          VAL_SET(x, 0xFF, 2, 0)
#define XOFFL       0x53 /* OFFSET_X[7:0] */
#define   XOFFL_SET(x)          VAL_SET(x, 0xFF, 0, 0)
#define YOFFL       0x54 /* OFFSET_Y[7:0] */
#define   YOFFL_SET(x)          VAL_SET(x, 0xFF, 0, 0)
#define VHYX        0x55 /* Offset and size completion */
#define   VHYX_VSIZE_SET(x)     VAL_SET(x, 0x1, (8+2), 7)
#define   VHYX_HSIZE_SET(x)     VAL_SET(x, 0x1, (8+2), 3)
#define   VHYX_YOFF_SET(x)      VAL_SET(x, 0x3, 8, 4)
#define   VHYX_XOFF_SET(x)      VAL_SET(x, 0x3, 8, 0)
#define DPRP        0x56
#define TEST        0x57 /* Horizontal size completion */
#define   TEST_HSIZE_SET(x)     VAL_SET(x, 0x1, (9+2), 7)
#define ZMOW        0x5A /* Zoom: Out Width  OUTW[7:0] (real/4) */
#define   ZMOW_OUTW_SET(x)      VAL_SET(x, 0xFF, 2, 0)
#define ZMOH        0x5B /* Zoom: Out Height OUTH[7:0] (real/4) */
#define   ZMOH_OUTH_SET(x)      VAL_SET(x, 0xFF, 2, 0)
#define ZMHH        0x5C /* Zoom: Speed and H&W completion */
#define   ZMHH_ZSPEED_SET(x)    VAL_SET(x, 0x0F, 0, 4)
#define   ZMHH_OUTH_SET(x)      VAL_SET(x, 0x1, (8+2), 2)
#define   ZMHH_OUTW_SET(x)      VAL_SET(x, 0x3, (8+2), 0)
#define BPADDR      0x7C /* SDE Indirect Register Access: Address */
#define BPDATA      0x7D /* SDE Indirect Register Access: Data */
#define CTRL2       0x86 /* DSP Module enable 2 */
#define   CTRL2_DCW_EN          0x20
#define   CTRL2_SDE_EN          0x10
#define   CTRL2_UV_ADJ_EN       0x08
#define   CTRL2_UV_AVG_EN       0x04
#define   CTRL2_CMX_EN          0x01
#define CTRL3       0x87 /* DSP Module enable 3 */
#define   CTRL3_BPC_EN          0x80
#define   CTRL3_WPC_EN          0x40
#define SIZEL       0x8C /* Image Size Completion */
#define   SIZEL_HSIZE8_11_SET(x) VAL_SET(x, 0x1, 11, 6)
#define   SIZEL_HSIZE8_SET(x)    VAL_SET(x, 0x7, 0, 3)
#define   SIZEL_VSIZE8_SET(x)    VAL_SET(x, 0x7, 0, 0)
#define HSIZE8      0xC0 /* Image Horizontal Size HSIZE[10:3] */
#define   HSIZE8_SET(x)         VAL_SET(x, 0xFF, 3, 0)
#define VSIZE8      0xC1 /* Image Vertical Size VSIZE[10:3] */
#define   VSIZE8_SET(x)         VAL_SET(x, 0xFF, 3, 0)
#define CTRL0       0xC2 /* DSP Module enable 0 */
#define   CTRL0_AEC_EN       0x80
#define   CTRL0_AEC_SEL      0x40
#define   CTRL0_STAT_SEL     0x20
#define   CTRL0_VFIRST       0x10
#define   CTRL0_YUV422       0x08
#define   CTRL0_YUV_EN       0x04
#define   CTRL0_RGB_EN       0x02
#define   CTRL0_RAW_EN       0x01
#define CTRL1       0xC3 /* DSP Module enable 1 */
#define   CTRL1_CIP          0x80
#define   CTRL1_DMY          0x40
#define   CTRL1_RAW_GMA      0x20
#define   CTRL1_DG           0x10
#define   CTRL1_AWB          0x08
#define   CTRL1_AWB_GAIN     0x04
#define   CTRL1_LENC         0x02
#define   CTRL1_PRE          0x01
#define R_DVP_SP    0xD3 /* DVP output speed control */
#define   R_DVP_SP_AUTO_MODE 0x80
#define   R_DVP_SP_DVP_MASK  0x3F /* DVP PCLK = sysclk (48)/[6:0] (YUV0);
				   *          = sysclk (48)/(2*[6:0]) (RAW);*/
#define IMAGE_MODE  0xDA /* Image Output Format Select */
#define   IMAGE_MODE_Y8_DVP_EN   0x40
#define   IMAGE_MODE_JPEG_EN     0x10
#define   IMAGE_MODE_YUV422      0x00
#define   IMAGE_MODE_RAW10       0x04 /* (DVP) */
#define   IMAGE_MODE_RGB565      0x08
#define   IMAGE_MODE_HREF_VSYNC  0x02 /* HREF timing select in DVP JPEG output
				       * mode (0 for HREF is same as sensor) */
#define   IMAGE_MODE_LBYTE_FIRST 0x01 /* Byte swap enable for DVP
				       *    1: Low byte first UYVY (C2[4] =0)
				       *        VYUY (C2[4] =1)
				       *    0: High byte first YUYV (C2[4]=0)
				       *        YVYU (C2[4] = 1) */
#define RESET       0xE0 /* Reset */
#define   RESET_MICROC       0x40
#define   RESET_SCCB         0x20
#define   RESET_JPEG         0x10
#define   RESET_DVP          0x04
#define   RESET_IPU          0x02
#define   RESET_CIF          0x01
#define REGED       0xED /* Register ED */
#define   REGED_CLK_OUT_DIS  0x10
#define MS_SP       0xF0 /* SCCB Master Speed */
#define SS_ID       0xF7 /* SCCB Slave ID */
#define SS_CTRL     0xF8 /* SCCB Slave Control */
#define   SS_CTRL_ADD_AUTO_INC  0x20
#define   SS_CTRL_EN            0x08
#define   SS_CTRL_DELAY_CLK     0x04
#define   SS_CTRL_ACC_EN        0x02
#define   SS_CTRL_SEN_PASS_THR  0x01
#define MC_BIST     0xF9 /* Microcontroller misc register */
#define   MC_BIST_RESET           0x80 /* Microcontroller Reset */
#define   MC_BIST_BOOT_ROM_SEL    0x40
#define   MC_BIST_12KB_SEL        0x20
#define   MC_BIST_12KB_MASK       0x30
#define   MC_BIST_512KB_SEL       0x08
#define   MC_BIST_512KB_MASK      0x0C
#define   MC_BIST_BUSY_BIT_R      0x02
#define   MC_BIST_MC_RES_ONE_SH_W 0x02
#define   MC_BIST_LAUNCH          0x01
#define BANK_SEL    0xFF /* Register Bank Select */
#define   BANK_SEL_DSP     0x00
#define   BANK_SEL_SENS    0x01

/*
 * Sensor registers
 * register offset for BANK_SEL == BANK_SEL_SENS
 */
#define GAIN        0x00 /* AGC - Gain control gain setting */
#define COM1        0x03 /* Common control 1 */
#define   COM1_1_DUMMY_FR          0x40
#define   COM1_3_DUMMY_FR          0x80
#define   COM1_7_DUMMY_FR          0xC0
#define   COM1_VWIN_LSB_UXGA       0x0F
#define   COM1_VWIN_LSB_SVGA       0x0A
#define   COM1_VWIN_LSB_CIF        0x06
#define REG04       0x04 /* Register 04 */
#define   REG04_DEF             0x20 /* Always set */
#define   REG04_HFLIP_IMG       0x80 /* Horizontal mirror image ON/OFF */
#define   REG04_VFLIP_IMG       0x40 /* Vertical flip image ON/OFF */
#define   REG04_VREF_EN         0x10
#define   REG04_HREF_EN         0x08
#define   REG04_AEC_SET(x)      VAL_SET(x, 0x3, 0, 0)
#define REG08       0x08 /* Frame Exposure One-pin Control Pre-charge Row Num */
#define COM2        0x09 /* Common control 2 */
#define   COM2_SOFT_SLEEP_MODE  0x10 /* Soft sleep mode */
				     /* Output drive capability */
#define   COM2_OCAP_Nx_SET(N)   (((N) - 1) & 0x03) /* N = [1x .. 4x] */
#define PID         0x0A /* Product ID Number MSB */
#define VER         0x0B /* Product ID Number LSB */
#define COM3        0x0C /* Common control 3 */
#define   COM3_BAND_50H        0x04 /* 0 For Banding at 60H */
#define   COM3_BAND_AUTO       0x02 /* Auto Banding */
#define   COM3_SING_FR_SNAPSH  0x01 /* 0 For enable live video output after the
				     * snapshot sequence*/
#define AEC         0x10 /* AEC[9:2] Exposure Value */
#define CLKRC       0x11 /* Internal clock */
#define   CLKRC_EN             0x80
#define   CLKRC_DIV_SET(x)     (((x) - 1) & 0x1F) /* CLK = XVCLK/(x) */
#define COM7        0x12 /* Common control 7 */
#define   COM7_SRST            0x80 /* Initiates system reset. All registers are
				     * set to factory default values after which
				     * the chip resumes normal operation */
#define   COM7_RES_UXGA        0x00 /* Resolution selectors for UXGA */
#define   COM7_RES_SVGA        0x40 /* SVGA */
#define   COM7_RES_CIF         0x20 /* CIF */
#define   COM7_ZOOM_EN         0x04 /* Enable Zoom mode */
#define   COM7_COLOR_BAR_TEST  0x02 /* Enable Color Bar Test Pattern */
#define COM8        0x13 /* Common control 8 */
#define   COM8_DEF             0xC0 /* Banding filter ON/OFF */
#define   COM8_BNDF_EN         0x20 /* Banding filter ON/OFF */
#define   COM8_AGC_EN          0x04 /* AGC Auto/Manual control selection */
#define   COM8_AEC_EN          0x01 /* Auto/Manual Exposure control */
#define COM9        0x14 /* Common control 9
			  * Automatic gain ceiling - maximum AGC value [7:5]*/
#define   COM9_AGC_GAIN_2x     0x00 /* 000 :   2x */
#define   COM9_AGC_GAIN_4x     0x20 /* 001 :   4x */
#define   COM9_AGC_GAIN_8x     0x40 /* 010 :   8x */
#define   COM9_AGC_GAIN_16x    0x60 /* 011 :  16x */
#define   COM9_AGC_GAIN_32x    0x80 /* 100 :  32x */
#define   COM9_AGC_GAIN_64x    0xA0 /* 101 :  64x */
#define   COM9_AGC_GAIN_128x   0xC0 /* 110 : 128x */
#define COM10       0x15 /* Common control 10 */
#define   COM10_PCLK_HREF      0x20 /* PCLK output qualified by HREF */
#define   COM10_PCLK_RISE      0x10 /* Data is updated at the rising edge of
				     * PCLK (user can latch data at the next
				     * falling edge of PCLK).
				     * 0 otherwise. */
#define   COM10_HREF_INV       0x08 /* Invert HREF polarity:
				     * HREF negative for valid data*/
#define   COM10_VSINC_INV      0x02 /* Invert VSYNC polarity */
#define HSTART      0x17 /* Horizontal Window start MSB 8 bit */
#define HEND        0x18 /* Horizontal Window end MSB 8 bit */
#define VSTART      0x19 /* Vertical Window start MSB 8 bit */
#define VEND        0x1A /* Vertical Window end MSB 8 bit */
#define MIDH        0x1C /* Manufacturer ID byte - high */
#define MIDL        0x1D /* Manufacturer ID byte - low  */
#define AEW         0x24 /* AGC/AEC - Stable operating region (upper limit) */
#define AEB         0x25 /* AGC/AEC - Stable operating region (lower limit) */
#define VV          0x26 /* AGC/AEC Fast mode operating region */
#define   VV_HIGH_TH_SET(x)      VAL_SET(x, 0xF, 0, 4)
#define   VV_LOW_TH_SET(x)       VAL_SET(x, 0xF, 0, 0)
#define REG2A       0x2A /* Dummy pixel insert MSB */
#define FRARL       0x2B /* Dummy pixel insert LSB */
#define ADDVFL      0x2D /* LSB of insert dummy lines in Vertical direction */
#define ADDVFH      0x2E /* MSB of insert dummy lines in Vertical direction */
#define YAVG        0x2F /* Y/G Channel Average value */
#define REG32       0x32 /* Common Control 32 */
#define   REG32_PCLK_DIV_2    0x80 /* PCLK freq divided by 2 */
#define   REG32_PCLK_DIV_4    0xC0 /* PCLK freq divided by 4 */
#define ARCOM2      0x34 /* Zoom: Horizontal start point */
#define REG45       0x45 /* Register 45 */
#define FLL         0x46 /* Frame Length Adjustment LSBs */
#define FLH         0x47 /* Frame Length Adjustment MSBs */
#define COM19       0x48 /* Zoom: Vertical start point */
#define ZOOMS       0x49 /* Zoom: Vertical start point */
#define COM22       0x4B /* Flash light control */
#define COM25       0x4E /* For Banding operations */
#define BD50        0x4F /* 50Hz Banding AEC 8 LSBs */
#define BD60        0x50 /* 60Hz Banding AEC 8 LSBs */
#define REG5D       0x5D /* AVGsel[7:0],   16-zone average weight option */
#define REG5E       0x5E /* AVGsel[15:8],  16-zone average weight option */
#define REG5F       0x5F /* AVGsel[23:16], 16-zone average weight option */
#define REG60       0x60 /* AVGsel[31:24], 16-zone average weight option */
#define HISTO_LOW   0x61 /* Histogram Algorithm Low Level */
#define HISTO_HIGH  0x62 /* Histogram Algorithm High Level */

/*
 * ID
 */
#define MANUFACTURER_ID	0x7FA2
#define PID_OV2640	0x2642
#define VERSION(pid, ver) ((pid << 8) | (ver & 0xFF))

/*
 * Struct
 */
struct regval_list {
	u8 reg_num;
	u8 value;
};

/* Supported resolutions */
enum ov2640_width {
	W_QCIF	= 176,
	W_QVGA	= 320,
	W_CIF	= 352,
	W_VGA	= 640,
	W_SVGA	= 800,
	W_XGA	= 1024,
	W_SXGA	= 1280,
	W_UXGA	= 1600,
};

enum ov2640_height {
	H_QCIF	= 144,
	H_QVGA	= 240,
	H_CIF	= 288,
	H_VGA	= 480,
	H_SVGA	= 600,
	H_XGA	= 768,
	H_SXGA	= 1024,
	H_UXGA	= 1200,
};

struct ov2640_win_size {
	char				*name;
	enum ov2640_width		width;
	enum ov2640_height		height;
	const struct regval_list	*regs;
};


struct ov2640_priv {
	struct v4l2_subdev		subdev;
	struct v4l2_ctrl_handler	hdl;
	enum v4l2_mbus_pixelcode	cfmt_code;
	struct v4l2_clk			*clk;
	const struct ov2640_win_size	*win;
};

/*
 * Registers settings
 */

#define ENDMARKER { 0xff, 0xff }

static const struct regval_list ov2640_init_regs[] = {
	{ BANK_SEL, BANK_SEL_DSP },
	{ 0x2c,   0xff },
	{ 0x2e,   0xdf },
	{ BANK_SEL, BANK_SEL_SENS },
	{ 0x3c,   0x32 },
	{ CLKRC, CLKRC_DIV_SET(1) },
	{ COM2, COM2_OCAP_Nx_SET(3) },
	{ REG04, REG04_DEF | REG04_HREF_EN },
	{ COM8,  COM8_DEF | COM8_BNDF_EN | COM8_AGC_EN | COM8_AEC_EN },
	{ COM9, COM9_AGC_GAIN_8x | 0x08},
	{ 0x2c,   0x0c },
	{ 0x33,   0x78 },
	{ 0x3a,   0x33 },
	{ 0x3b,   0xfb },
	{ 0x3e,   0x00 },
	{ 0x43,   0x11 },
	{ 0x16,   0x10 },
	{ 0x39,   0x02 },
	{ 0x35,   0x88 },
	{ 0x22,   0x0a },
	{ 0x37,   0x40 },
	{ 0x23,   0x00 },
	{ ARCOM2, 0xa0 },
	{ 0x06,   0x02 },
	{ 0x06,   0x88 },
	{ 0x07,   0xc0 },
	{ 0x0d,   0xb7 },
	{ 0x0e,   0x01 },
	{ 0x4c,   0x00 },
	{ 0x4a,   0x81 },
	{ 0x21,   0x99 },
	{ AEW,    0x40 },
	{ AEB,    0x38 },
	{ VV,     VV_HIGH_TH_SET(0x08) | VV_LOW_TH_SET(0x02) },
	{ 0x5c,   0x00 },
	{ 0x63,   0x00 },
	{ FLL,    0x22 },
	{ COM3,   0x38 | COM3_BAND_AUTO },
	{ REG5D,  0x55 },
	{ REG5E,  0x7d },
	{ REG5F,  0x7d },
	{ REG60,  0x55 },
	{ HISTO_LOW,   0x70 },
	{ HISTO_HIGH,  0x80 },
	{ 0x7c,   0x05 },
	{ 0x20,   0x80 },
	{ 0x28,   0x30 },
	{ 0x6c,   0x00 },
	{ 0x6d,   0x80 },
	{ 0x6e,   0x00 },
	{ 0x70,   0x02 },
	{ 0x71,   0x94 },
	{ 0x73,   0xc1 },
	{ 0x3d,   0x34 },
	{ COM7, COM7_RES_UXGA | COM7_ZOOM_EN },
	{ 0x5a,   0x57 },
	{ BD50,   0xbb },
	{ BD60,   0x9c },
	{ BANK_SEL, BANK_SEL_DSP },
	{ 0xe5,   0x7f },
	{ MC_BIST, MC_BIST_RESET | MC_BIST_BOOT_ROM_SEL },
	{ 0x41,   0x24 },
	{ RESET, RESET_JPEG | RESET_DVP },
	{ 0x76,   0xff },
	{ 0x33,   0xa0 },
	{ 0x42,   0x20 },
	{ 0x43,   0x18 },
	{ 0x4c,   0x00 },
	{ CTRL3, CTRL3_BPC_EN | CTRL3_WPC_EN | 0x10 },
	{ 0x88,   0x3f },
	{ 0xd7,   0x03 },
	{ 0xd9,   0x10 },
	{ R_DVP_SP , R_DVP_SP_AUTO_MODE | 0x2 },
	{ 0xc8,   0x08 },
	{ 0xc9,   0x80 },
	{ BPADDR, 0x00 },
	{ BPDATA, 0x00 },
	{ BPADDR, 0x03 },
	{ BPDATA, 0x48 },
	{ BPDATA, 0x48 },
	{ BPADDR, 0x08 },
	{ BPDATA, 0x20 },
	{ BPDATA, 0x10 },
	{ BPDATA, 0x0e },
	{ 0x90,   0x00 },
	{ 0x91,   0x0e },
	{ 0x91,   0x1a },
	{ 0x91,   0x31 },
	{ 0x91,   0x5a },
	{ 0x91,   0x69 },
	{ 0x91,   0x75 },
	{ 0x91,   0x7e },
	{ 0x91,   0x88 },
	{ 0x91,   0x8f },
	{ 0x91,   0x96 },
	{ 0x91,   0xa3 },
	{ 0x91,   0xaf },
	{ 0x91,   0xc4 },
	{ 0x91,   0xd7 },
	{ 0x91,   0xe8 },
	{ 0x91,   0x20 },
	{ 0x92,   0x00 },
	{ 0x93,   0x06 },
	{ 0x93,   0xe3 },
	{ 0x93,   0x03 },
	{ 0x93,   0x03 },
	{ 0x93,   0x00 },
	{ 0x93,   0x02 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x93,   0x00 },
	{ 0x96,   0x00 },
	{ 0x97,   0x08 },
	{ 0x97,   0x19 },
	{ 0x97,   0x02 },
	{ 0x97,   0x0c },
	{ 0x97,   0x24 },
	{ 0x97,   0x30 },
	{ 0x97,   0x28 },
	{ 0x97,   0x26 },
	{ 0x97,   0x02 },
	{ 0x97,   0x98 },
	{ 0x97,   0x80 },
	{ 0x97,   0x00 },
	{ 0x97,   0x00 },
	{ 0xa4,   0x00 },
	{ 0xa8,   0x00 },
	{ 0xc5,   0x11 },
	{ 0xc6,   0x51 },
	{ 0xbf,   0x80 },
	{ 0xc7,   0x10 },
	{ 0xb6,   0x66 },
	{ 0xb8,   0xA5 },
	{ 0xb7,   0x64 },
	{ 0xb9,   0x7C },
	{ 0xb3,   0xaf },
	{ 0xb4,   0x97 },
	{ 0xb5,   0xFF },
	{ 0xb0,   0xC5 },
	{ 0xb1,   0x94 },
	{ 0xb2,   0x0f },
	{ 0xc4,   0x5c },
	{ 0xa6,   0x00 },
	{ 0xa7,   0x20 },
	{ 0xa7,   0xd8 },
	{ 0xa7,   0x1b },
	{ 0xa7,   0x31 },
	{ 0xa7,   0x00 },
	{ 0xa7,   0x18 },
	{ 0xa7,   0x20 },
	{ 0xa7,   0xd8 },
	{ 0xa7,   0x19 },
	{ 0xa7,   0x31 },
	{ 0xa7,   0x00 },
	{ 0xa7,   0x18 },
	{ 0xa7,   0x20 },
	{ 0xa7,   0xd8 },
	{ 0xa7,   0x19 },
	{ 0xa7,   0x31 },
	{ 0xa7,   0x00 },
	{ 0xa7,   0x18 },
	{ 0x7f,   0x00 },
	{ 0xe5,   0x1f },
	{ 0xe1,   0x77 },
	{ 0xdd,   0x7f },
	{ CTRL0,  CTRL0_YUV422 | CTRL0_YUV_EN | CTRL0_RGB_EN },
	ENDMARKER,
};

/*
 * Register settings for window size
 * The preamble, setup the internal DSP to input an UXGA (1600x1200) image.
 * Then the different zooming configurations will setup the output image size.
 */
static const struct regval_list ov2640_size_change_preamble_regs[] = {
	{ BANK_SEL, BANK_SEL_DSP },
	{ RESET, RESET_DVP },
	{ HSIZE8, HSIZE8_SET(W_UXGA) },
	{ VSIZE8, VSIZE8_SET(H_UXGA) },
	{ CTRL2, CTRL2_DCW_EN | CTRL2_SDE_EN |
		 CTRL2_UV_AVG_EN | CTRL2_CMX_EN | CTRL2_UV_ADJ_EN },
	{ HSIZE, HSIZE_SET(W_UXGA) },
	{ VSIZE, VSIZE_SET(H_UXGA) },
	{ XOFFL, XOFFL_SET(0) },
	{ YOFFL, YOFFL_SET(0) },
	{ VHYX, VHYX_HSIZE_SET(W_UXGA) | VHYX_VSIZE_SET(H_UXGA) |
		VHYX_XOFF_SET(0) | VHYX_YOFF_SET(0)},
	{ TEST, TEST_HSIZE_SET(W_UXGA) },
	ENDMARKER,
};

#define PER_SIZE_REG_SEQ(x, y, v_div, h_div, pclk_div)	\
	{ CTRLI, CTRLI_LP_DP | CTRLI_V_DIV_SET(v_div) |	\
		 CTRLI_H_DIV_SET(h_div)},		\
	{ ZMOW, ZMOW_OUTW_SET(x) },			\
	{ ZMOH, ZMOH_OUTH_SET(y) },			\
	{ ZMHH, ZMHH_OUTW_SET(x) | ZMHH_OUTH_SET(y) },	\
	{ R_DVP_SP, pclk_div },				\
	{ RESET, 0x00}

static const struct regval_list ov2640_qcif_regs[] = {
	PER_SIZE_REG_SEQ(W_QCIF, H_QCIF, 3, 3, 4),
	ENDMARKER,
};

static const struct regval_list ov2640_qvga_regs[] = {
	PER_SIZE_REG_SEQ(W_QVGA, H_QVGA, 2, 2, 4),
	ENDMARKER,
};

static const struct regval_list ov2640_cif_regs[] = {
	PER_SIZE_REG_SEQ(W_CIF, H_CIF, 2, 2, 8),
	ENDMARKER,
};

static const struct regval_list ov2640_vga_regs[] = {
	PER_SIZE_REG_SEQ(W_VGA, H_VGA, 0, 0, 2),
	ENDMARKER,
};

static const struct regval_list ov2640_svga_regs[] = {
	PER_SIZE_REG_SEQ(W_SVGA, H_SVGA, 1, 1, 2),
	ENDMARKER,
};

static const struct regval_list ov2640_xga_regs[] = {
	PER_SIZE_REG_SEQ(W_XGA, H_XGA, 0, 0, 2),
	{ CTRLI,    0x00},
	ENDMARKER,
};

static const struct regval_list ov2640_sxga_regs[] = {
	PER_SIZE_REG_SEQ(W_SXGA, H_SXGA, 0, 0, 2),
	{ CTRLI,    0x00},
	{ R_DVP_SP, 2 | R_DVP_SP_AUTO_MODE },
	ENDMARKER,
};

static const struct regval_list ov2640_uxga_regs[] = {
	PER_SIZE_REG_SEQ(W_UXGA, H_UXGA, 0, 0, 0),
	{ CTRLI,    0x00},
	{ R_DVP_SP, 0 | R_DVP_SP_AUTO_MODE },
	ENDMARKER,
};

#define OV2640_SIZE(n, w, h, r) \
	{.name = n, .width = w , .height = h, .regs = r }

static const struct ov2640_win_size ov2640_supported_win_sizes[] = {
	OV2640_SIZE("QCIF", W_QCIF, H_QCIF, ov2640_qcif_regs),
	OV2640_SIZE("QVGA", W_QVGA, H_QVGA, ov2640_qvga_regs),
	OV2640_SIZE("CIF", W_CIF, H_CIF, ov2640_cif_regs),
	OV2640_SIZE("VGA", W_VGA, H_VGA, ov2640_vga_regs),
	OV2640_SIZE("SVGA", W_SVGA, H_SVGA, ov2640_svga_regs),
	OV2640_SIZE("XGA", W_XGA, H_XGA, ov2640_xga_regs),
	OV2640_SIZE("SXGA", W_SXGA, H_SXGA, ov2640_sxga_regs),
	OV2640_SIZE("UXGA", W_UXGA, H_UXGA, ov2640_uxga_regs),
};

/*
 * Register settings for pixel formats
 */
static const struct regval_list ov2640_format_change_preamble_regs[] = {
	{ BANK_SEL, BANK_SEL_DSP },
	{ R_BYPASS, R_BYPASS_USE_DSP },
	ENDMARKER,
};

static const struct regval_list ov2640_yuyv_regs[] = {
	{ IMAGE_MODE, IMAGE_MODE_YUV422 },
	{ 0xd7, 0x03 },
	{ 0x33, 0xa0 },
	{ 0xe5, 0x1f },
	{ 0xe1, 0x67 },
	{ RESET,  0x00 },
	{ R_BYPASS, R_BYPASS_USE_DSP },
	ENDMARKER,
};

static const struct regval_list ov2640_uyvy_regs[] = {
	{ IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_YUV422 },
	{ 0xd7, 0x01 },
	{ 0x33, 0xa0 },
	{ 0xe1, 0x67 },
	{ RESET,  0x00 },
	{ R_BYPASS, R_BYPASS_USE_DSP },
	ENDMARKER,
};

static const struct regval_list ov2640_rgb565_be_regs[] = {
	{ IMAGE_MODE, IMAGE_MODE_RGB565 },
	{ 0xd7, 0x03 },
	{ RESET,  0x00 },
	{ R_BYPASS, R_BYPASS_USE_DSP },
	ENDMARKER,
};

static const struct regval_list ov2640_rgb565_le_regs[] = {
	{ IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_RGB565 },
	{ 0xd7, 0x03 },
	{ RESET,  0x00 },
	{ R_BYPASS, R_BYPASS_USE_DSP },
	ENDMARKER,
};

static enum v4l2_mbus_pixelcode ov2640_codes[] = {
	V4L2_MBUS_FMT_YUYV8_2X8,
	V4L2_MBUS_FMT_UYVY8_2X8,
	V4L2_MBUS_FMT_RGB565_2X8_BE,
	V4L2_MBUS_FMT_RGB565_2X8_LE,
};

/*
 * General functions
 */
static struct ov2640_priv *to_ov2640(const struct i2c_client *client)
{
	return container_of(i2c_get_clientdata(client), struct ov2640_priv,
			    subdev);
}

static int ov2640_write_array(struct i2c_client *client,
			      const struct regval_list *vals)
{
	int ret;

	while ((vals->reg_num != 0xff) || (vals->value != 0xff)) {
		ret = i2c_smbus_write_byte_data(client,
						vals->reg_num, vals->value);
		dev_vdbg(&client->dev, "array: 0x%02x, 0x%02x",
			 vals->reg_num, vals->value);

		if (ret < 0)
			return ret;
		vals++;
	}
	return 0;
}

static int ov2640_mask_set(struct i2c_client *client,
			   u8  reg, u8  mask, u8  set)
{
	s32 val = i2c_smbus_read_byte_data(client, reg);
	if (val < 0)
		return val;

	val &= ~mask;
	val |= set & mask;

	dev_vdbg(&client->dev, "masks: 0x%02x, 0x%02x", reg, val);

	return i2c_smbus_write_byte_data(client, reg, val);
}

static int ov2640_reset(struct i2c_client *client)
{
	int ret;
	const struct regval_list reset_seq[] = {
		{BANK_SEL, BANK_SEL_SENS},
		{COM7, COM7_SRST},
		ENDMARKER,
	};

	ret = ov2640_write_array(client, reset_seq);
	if (ret)
		goto err;

	msleep(5);
err:
	dev_dbg(&client->dev, "%s: (ret %d)", __func__, ret);
	return ret;
}

/*
 * soc_camera_ops functions
 */
static int ov2640_s_stream(struct v4l2_subdev *sd, int enable)
{
	return 0;
}

static int ov2640_s_ctrl(struct v4l2_ctrl *ctrl)
{
	struct v4l2_subdev *sd =
		&container_of(ctrl->handler, struct ov2640_priv, hdl)->subdev;
	struct i2c_client  *client = v4l2_get_subdevdata(sd);
	u8 val;
	int ret;

	ret = i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS);
	if (ret < 0)
		return ret;

	switch (ctrl->id) {
	case V4L2_CID_VFLIP:
		val = ctrl->val ? REG04_VFLIP_IMG : 0x00;
		return ov2640_mask_set(client, REG04, REG04_VFLIP_IMG, val);
	case V4L2_CID_HFLIP:
		val = ctrl->val ? REG04_HFLIP_IMG : 0x00;
		return ov2640_mask_set(client, REG04, REG04_HFLIP_IMG, val);
	}

	return -EINVAL;
}

#ifdef CONFIG_VIDEO_ADV_DEBUG
static int ov2640_g_register(struct v4l2_subdev *sd,
			     struct v4l2_dbg_register *reg)
{
	struct i2c_client *client = v4l2_get_subdevdata(sd);
	int ret;

	reg->size = 1;
	if (reg->reg > 0xff)
		return -EINVAL;

	ret = i2c_smbus_read_byte_data(client, reg->reg);
	if (ret < 0)
		return ret;

	reg->val = ret;

	return 0;
}

static int ov2640_s_register(struct v4l2_subdev *sd,
			     const struct v4l2_dbg_register *reg)
{
	struct i2c_client *client = v4l2_get_subdevdata(sd);

	if (reg->reg > 0xff ||
	    reg->val > 0xff)
		return -EINVAL;

	return i2c_smbus_write_byte_data(client, reg->reg, reg->val);
}
#endif

static int ov2640_s_power(struct v4l2_subdev *sd, int on)
{
	struct i2c_client *client = v4l2_get_subdevdata(sd);
	struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
	struct ov2640_priv *priv = to_ov2640(client);

	return soc_camera_set_power(&client->dev, ssdd, priv->clk, on);
}

/* Select the nearest higher resolution for capture */
static const struct ov2640_win_size *ov2640_select_win(u32 *width, u32 *height)
{
	int i, default_size = ARRAY_SIZE(ov2640_supported_win_sizes) - 1;

	for (i = 0; i < ARRAY_SIZE(ov2640_supported_win_sizes); i++) {
		if (ov2640_supported_win_sizes[i].width  >= *width &&
		    ov2640_supported_win_sizes[i].height >= *height) {
			*width = ov2640_supported_win_sizes[i].width;
			*height = ov2640_supported_win_sizes[i].height;
			return &ov2640_supported_win_sizes[i];
		}
	}

	*width = ov2640_supported_win_sizes[default_size].width;
	*height = ov2640_supported_win_sizes[default_size].height;
	return &ov2640_supported_win_sizes[default_size];
}

static int ov2640_set_params(struct i2c_client *client, u32 *width, u32 *height,
			     enum v4l2_mbus_pixelcode code)
{
	struct ov2640_priv       *priv = to_ov2640(client);
	const struct regval_list *selected_cfmt_regs;
	int ret;

	/* select win */
	priv->win = ov2640_select_win(width, height);

	/* select format */
	priv->cfmt_code = 0;
	switch (code) {
	case V4L2_MBUS_FMT_RGB565_2X8_BE:
		dev_dbg(&client->dev, "%s: Selected cfmt RGB565 BE", __func__);
		selected_cfmt_regs = ov2640_rgb565_be_regs;
		break;
	case V4L2_MBUS_FMT_RGB565_2X8_LE:
		dev_dbg(&client->dev, "%s: Selected cfmt RGB565 LE", __func__);
		selected_cfmt_regs = ov2640_rgb565_le_regs;
		break;
	case V4L2_MBUS_FMT_YUYV8_2X8:
		dev_dbg(&client->dev, "%s: Selected cfmt YUYV (YUV422)", __func__);
		selected_cfmt_regs = ov2640_yuyv_regs;
		break;
	default:
	case V4L2_MBUS_FMT_UYVY8_2X8:
		dev_dbg(&client->dev, "%s: Selected cfmt UYVY", __func__);
		selected_cfmt_regs = ov2640_uyvy_regs;
	}

	/* reset hardware */
	ov2640_reset(client);

	/* initialize the sensor with default data */
	dev_dbg(&client->dev, "%s: Init default", __func__);
	ret = ov2640_write_array(client, ov2640_init_regs);
	if (ret < 0)
		goto err;

	/* select preamble */
	dev_dbg(&client->dev, "%s: Set size to %s", __func__, priv->win->name);
	ret = ov2640_write_array(client, ov2640_size_change_preamble_regs);
	if (ret < 0)
		goto err;

	/* set size win */
	ret = ov2640_write_array(client, priv->win->regs);
	if (ret < 0)
		goto err;

	/* cfmt preamble */
	dev_dbg(&client->dev, "%s: Set cfmt", __func__);
	ret = ov2640_write_array(client, ov2640_format_change_preamble_regs);
	if (ret < 0)
		goto err;

	/* set cfmt */
	ret = ov2640_write_array(client, selected_cfmt_regs);
	if (ret < 0)
		goto err;

	priv->cfmt_code = code;
	*width = priv->win->width;
	*height = priv->win->height;

	return 0;

err:
	dev_err(&client->dev, "%s: Error %d", __func__, ret);
	ov2640_reset(client);
	priv->win = NULL;

	return ret;
}

static int ov2640_g_fmt(struct v4l2_subdev *sd,
			struct v4l2_mbus_framefmt *mf)
{
	struct i2c_client  *client = v4l2_get_subdevdata(sd);
	struct ov2640_priv *priv = to_ov2640(client);

	if (!priv->win) {
		u32 width = W_SVGA, height = H_SVGA;
		priv->win = ov2640_select_win(&width, &height);
		priv->cfmt_code = V4L2_MBUS_FMT_UYVY8_2X8;
	}

	mf->width	= priv->win->width;
	mf->height	= priv->win->height;
	mf->code	= priv->cfmt_code;

	switch (mf->code) {
	case V4L2_MBUS_FMT_RGB565_2X8_BE:
	case V4L2_MBUS_FMT_RGB565_2X8_LE:
		mf->colorspace = V4L2_COLORSPACE_SRGB;
		break;
	default:
	case V4L2_MBUS_FMT_YUYV8_2X8:
	case V4L2_MBUS_FMT_UYVY8_2X8:
		mf->colorspace = V4L2_COLORSPACE_JPEG;
	}
	mf->field	= V4L2_FIELD_NONE;

	return 0;
}

static int ov2640_s_fmt(struct v4l2_subdev *sd,
			struct v4l2_mbus_framefmt *mf)
{
	struct i2c_client *client = v4l2_get_subdevdata(sd);
	int ret;


	switch (mf->code) {
	case V4L2_MBUS_FMT_RGB565_2X8_BE:
	case V4L2_MBUS_FMT_RGB565_2X8_LE:
		mf->colorspace = V4L2_COLORSPACE_SRGB;
		break;
	default:
		mf->code = V4L2_MBUS_FMT_UYVY8_2X8;
	case V4L2_MBUS_FMT_YUYV8_2X8:
	case V4L2_MBUS_FMT_UYVY8_2X8:
		mf->colorspace = V4L2_COLORSPACE_JPEG;
	}

	ret = ov2640_set_params(client, &mf->width, &mf->height, mf->code);

	return ret;
}

static int ov2640_try_fmt(struct v4l2_subdev *sd,
			  struct v4l2_mbus_framefmt *mf)
{
	/*
	 * select suitable win, but don't store it
	 */
	ov2640_select_win(&mf->width, &mf->height);

	mf->field	= V4L2_FIELD_NONE;

	switch (mf->code) {
	case V4L2_MBUS_FMT_RGB565_2X8_BE:
	case V4L2_MBUS_FMT_RGB565_2X8_LE:
		mf->colorspace = V4L2_COLORSPACE_SRGB;
		break;
	default:
		mf->code = V4L2_MBUS_FMT_UYVY8_2X8;
	case V4L2_MBUS_FMT_YUYV8_2X8:
	case V4L2_MBUS_FMT_UYVY8_2X8:
		mf->colorspace = V4L2_COLORSPACE_JPEG;
	}

	return 0;
}

static int ov2640_enum_fmt(struct v4l2_subdev *sd, unsigned int index,
			   enum v4l2_mbus_pixelcode *code)
{
	if (index >= ARRAY_SIZE(ov2640_codes))
		return -EINVAL;

	*code = ov2640_codes[index];
	return 0;
}

static int ov2640_g_crop(struct v4l2_subdev *sd, struct v4l2_crop *a)
{
	a->c.left	= 0;
	a->c.top	= 0;
	a->c.width	= W_UXGA;
	a->c.height	= H_UXGA;
	a->type		= V4L2_BUF_TYPE_VIDEO_CAPTURE;

	return 0;
}

static int ov2640_cropcap(struct v4l2_subdev *sd, struct v4l2_cropcap *a)
{
	a->bounds.left			= 0;
	a->bounds.top			= 0;
	a->bounds.width			= W_UXGA;
	a->bounds.height		= H_UXGA;
	a->defrect			= a->bounds;
	a->type				= V4L2_BUF_TYPE_VIDEO_CAPTURE;
	a->pixelaspect.numerator	= 1;
	a->pixelaspect.denominator	= 1;

	return 0;
}

static int ov2640_video_probe(struct i2c_client *client)
{
	struct ov2640_priv *priv = to_ov2640(client);
	u8 pid, ver, midh, midl;
	const char *devname;
	int ret;

	ret = ov2640_s_power(&priv->subdev, 1);
	if (ret < 0)
		return ret;

	/*
	 * check and show product ID and manufacturer ID
	 */
	i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS);
	pid  = i2c_smbus_read_byte_data(client, PID);
	ver  = i2c_smbus_read_byte_data(client, VER);
	midh = i2c_smbus_read_byte_data(client, MIDH);
	midl = i2c_smbus_read_byte_data(client, MIDL);

	switch (VERSION(pid, ver)) {
	case PID_OV2640:
		devname     = "ov2640";
		break;
	default:
		dev_err(&client->dev,
			"Product ID error %x:%x\n", pid, ver);
		ret = -ENODEV;
		goto done;
	}

	dev_info(&client->dev,
		 "%s Product ID %0x:%0x Manufacturer ID %x:%x\n",
		 devname, pid, ver, midh, midl);

	ret = v4l2_ctrl_handler_setup(&priv->hdl);

done:
	ov2640_s_power(&priv->subdev, 0);
	return ret;
}

static const struct v4l2_ctrl_ops ov2640_ctrl_ops = {
	.s_ctrl = ov2640_s_ctrl,
};

static struct v4l2_subdev_core_ops ov2640_subdev_core_ops = {
#ifdef CONFIG_VIDEO_ADV_DEBUG
	.g_register	= ov2640_g_register,
	.s_register	= ov2640_s_register,
#endif
	.s_power	= ov2640_s_power,
};

static int ov2640_g_mbus_config(struct v4l2_subdev *sd,
				struct v4l2_mbus_config *cfg)
{
	struct i2c_client *client = v4l2_get_subdevdata(sd);
	struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);

	cfg->flags = V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_MASTER |
		V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_HIGH |
		V4L2_MBUS_DATA_ACTIVE_HIGH;
	cfg->type = V4L2_MBUS_PARALLEL;
	cfg->flags = soc_camera_apply_board_flags(ssdd, cfg);

	return 0;
}

static struct v4l2_subdev_video_ops ov2640_subdev_video_ops = {
	.s_stream	= ov2640_s_stream,
	.g_mbus_fmt	= ov2640_g_fmt,
	.s_mbus_fmt	= ov2640_s_fmt,
	.try_mbus_fmt	= ov2640_try_fmt,
	.cropcap	= ov2640_cropcap,
	.g_crop		= ov2640_g_crop,
	.enum_mbus_fmt	= ov2640_enum_fmt,
	.g_mbus_config	= ov2640_g_mbus_config,
};

static struct v4l2_subdev_ops ov2640_subdev_ops = {
	.core	= &ov2640_subdev_core_ops,
	.video	= &ov2640_subdev_video_ops,
};

/*
 * i2c_driver functions
 */
static int ov2640_probe(struct i2c_client *client,
			const struct i2c_device_id *did)
{
	struct ov2640_priv	*priv;
	struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
	struct i2c_adapter	*adapter = to_i2c_adapter(client->dev.parent);
	int			ret;

	if (!ssdd) {
		dev_err(&adapter->dev,
			"OV2640: Missing platform_data for driver\n");
		return -EINVAL;
	}

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
		dev_err(&adapter->dev,
			"OV2640: I2C-Adapter doesn't support SMBUS\n");
		return -EIO;
	}

	priv = devm_kzalloc(&client->dev, sizeof(struct ov2640_priv), GFP_KERNEL);
	if (!priv) {
		dev_err(&adapter->dev,
			"Failed to allocate memory for private data!\n");
		return -ENOMEM;
	}

	v4l2_i2c_subdev_init(&priv->subdev, client, &ov2640_subdev_ops);
	v4l2_ctrl_handler_init(&priv->hdl, 2);
	v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops,
			V4L2_CID_VFLIP, 0, 1, 1, 0);
	v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops,
			V4L2_CID_HFLIP, 0, 1, 1, 0);
	priv->subdev.ctrl_handler = &priv->hdl;
	if (priv->hdl.error)
		return priv->hdl.error;

	priv->clk = v4l2_clk_get(&client->dev, "mclk");
	if (IS_ERR(priv->clk)) {
		ret = PTR_ERR(priv->clk);
		goto eclkget;
	}

	ret = ov2640_video_probe(client);
	if (ret) {
		v4l2_clk_put(priv->clk);
eclkget:
		v4l2_ctrl_handler_free(&priv->hdl);
	} else {
		dev_info(&adapter->dev, "OV2640 Probed\n");
	}

	return ret;
}

static int ov2640_remove(struct i2c_client *client)
{
	struct ov2640_priv       *priv = to_ov2640(client);

	v4l2_clk_put(priv->clk);
	v4l2_device_unregister_subdev(&priv->subdev);
	v4l2_ctrl_handler_free(&priv->hdl);
	return 0;
}

static const struct i2c_device_id ov2640_id[] = {
	{ "ov2640", 0 },
	{ }
};
MODULE_DEVICE_TABLE(i2c, ov2640_id);

static struct i2c_driver ov2640_i2c_driver = {
	.driver = {
		.name = "ov2640",
	},
	.probe    = ov2640_probe,
	.remove   = ov2640_remove,
	.id_table = ov2640_id,
};

module_i2c_driver(ov2640_i2c_driver);

MODULE_DESCRIPTION("SoC Camera driver for Omni Vision 2640 sensor");
MODULE_AUTHOR("Alberto Panizzo");
MODULE_LICENSE("GPL v2");